User Manual of DS-8104HMI-A Series Mobile DVR
Contents
1. interface Fig 5 8 There is one small yellow pane on the upper left side of the interface For PAL camera the whole screen is divided into 22 18 panes 22 15 for 36 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 NTSC Firstly move the yellow pane to your hope position and press EDIT key the yellow pane will be turned into red then you can use to expand downward amp to shrink upward to expand rightward fl to shrink leftward After you make sure the red mask area press EDIT key to save the mask area The area will be blacked in the preview image Fig 5 9 Press ESC key to cancel the mask area The maximum mask area is the full screen and the minimum size is only one pane You can setup 4 mask areas at most Press A key to clear all mask areas Fig 5 9 Preview Image with Mask Fig 5 8 Mask Area Setup Interface Note The mask areas can not be copied to other cameras There is no preview image and record image in the areas 5 2 6 Preview Properties In Preview menu you can setup preview mode screen switch time enable or disable audio preview and preview layout Step 1 Enter into Preview menu Fig 5 10 Step 2 Preview properties O Preview mode You can use dk or key to select one mode There are 1 Screen and 4 Screen option 37 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 O Switch time That is image preview switch time You can use dk or2. then move to the second window and do the same operation If you press O then the corresponding window will display x without an image O Save setup Press Confirm button to save preview properties Press Cancel or ESC key to abort Fig 5 10 5 3 Alarm setup 5 3 1 External Alarm Input and Relay Output External Alarm Input and Relay Output is used to setup every external alarm input and output parameters in Alarms menu Fig 5 11 Fig 5 11 38 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 External alarm input setup Select one alarm input from 1 2 3 4 and then choose an alarm type from Normal Open and Normal Close according to the sensor type External alarm input setup includes alarm in handling and alarm in schedule Alarm in handling includes record camera PTZ linkage trigger alarm out etc Fig 5 12 Fig 5 13 You can select channels to record for each alarm input VW means enable Only the selected camera can record link with PTZ and warn on screen after alarm in The linkage order is Alarm in gt Trigger camera gt Recording please refer to section 5 4 PTZ linkage order is Alarm in gt Trigger camera gt PTZ PTZ linkage can be setup in Alarms and PTZ Linkage interfaces Fig 5 13 Please make sure the camera has already linked with alarm in and preset points sequences cruises have been set The maximum number of preset points is 128
3. 2 Check the battery s power 3 Make sure the remote controller is not tampered 4 Check around and make sure there is no fluorescent lamp used After exclude all of above reasons please change a new remote controller if it still does not work please contact the supplier After exclude all of above reasons please change a new GPS module if it still does not work please contact the supplier Note In caves tunnels and some other environments there is no GPS signal Q Why dial up is failed A 1 Please make sure the device have wireless module inside 2 Please check the antenna is connected correctly and vertical 3 Please check the status of SIM card make sure it can work for dial up 4 Please check the module selection and corresponding parameters in Mobile setup gt Dial up setup 5 The weak 3G signal may also cause dial up failure please make sure the parameters are correct reboot the DVR and try again 62
4. 5 6 In Image Setup menu Fig 5 7 you can setup time display position in the image Move Active Frame to Position button on the right side of OSD and enter setup image you can usel dl YF Il l keys to move the OSD position Press EDIT key to select OSD format There are following OSD formats MM DD YYYY W hh mm ss default MM DD YYYY hh mm ss YYYY MM DD W hh mm ss YYYY MM DD hh mm ss Note Here YYYY means year MM means month DD means day W means weekday hh means hour mm means minute and ss means second In Image Setup menu you can define name for each camera On the right side of camera name is Position button you can setup camera name position by pressing this button You can copy the position to any other camera but please note that camera s name can not be copied Fig 5 7 5 2 4 Video Parameters Setup The video parameters include brightness contrast hue and saturation The parameters will affect the preview image and recorded image In Image Setup menu Fig 5 7 you can modify the parameters by entering Adjust interface 5 2 5 Mask Area Setup In some cases maybe you want mask the sensitive area This area will not be preview and recorded You can setup the area in Image Setup menu Enable the check box beside Privacy Mask item changes the flag into yY Press Area button on the right of mask check box and enter mask area setup
5. 56M 384k 168M 1 00M 450M 160k 70M 448k 196M 1 25M 562M 192k 84M 512k 225M 1 50M 675M 224k 98M 640k 281M 1 75M 787M 256k 112M 768k 337M 2 00M 900M 57 4 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Appendix B ETHERNET Connect Cable Made Method Material and tool One twist cable 8 pin the length can be defined as to the actual demand but must be within 100m 2 standard RJ45 head one tool for RJ45 Suggestion have a network cable test tool to test each cable made Pin definition To make the network cable according to the actual situation there are two options 1 Use the following left side method to make the network cable when DVR is connected with network hub or switch 2 Use the following right side method to make the cross network cable when DVR is directly connected with client end PC 1 white orange 1 white orange 1 white orange 1 white green 2 Orange 2 Orange 2 Orange 2 green 3 white green 3 white green 3 white green 3 white orange 4 blue 4 blue 4 blue 4 blue 5 white blue 5 white blue 5 white blue 5 white blue 6 green 6 green 6 green 6 Orange 7 white brown 7 white brown 7 white brown 7 white brown 8 brown 8
6. DVR V1 20 00 4 7 Backup Recorded Files 4 7 1 USB Backup Note The user must have Playback right Please connect with backup devices first such as USB flash USB HDD and SATA device Please enter the layback interface to apply the backup operation Fig 4 9 There are two methods of backup 1 Backup the selected recorded files In the playback interface search the matched files move Active Frame and press Edit key to select the files The symbol v is the selecting tag Then select backup device move Active Frame to Copy button and press ENTER key to start backup You also can back up the image segments when the image is being playback The steps are as follow Step 1 Enter the interface of playback the files or playback by time Step 2 Press EDIT key to start selecting the current playback image and press EDIT again to stop Fig 4 9 Backup Recorded Files selecting This segment is selected Step 3 You can repeat step 2 to select more segments 30 MAX Step 4 After you select all segments Press ESC key a message window will pop up If you press Confirm button DVR will start to back up the selected segments If you press Cancel button DVR will abort the backup 29 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 2 Backup all the files in a certain period of time After entering the playback interface move Active Frame to Backup Setup butt
7. The alarm input connection is as Fig 2 9 Alarm Output connection DS 8104HMI M XX series mobile DVR is applied closed signal to trigger the alarm output That means when alarm output is triggered the Alarm OUT and GND will be connected status that means user must connect alarm device with power supply The alarm output connection is as Fig 2 10 Connection Description Detailed steps are as below 1 Pull out the green plug in the device 2 Loosen the screws in the plug with mini cross screw insert the signal wire into the corresponding pinholes 3 Then insert the green plug into the corresponding socket 16 Mobile DVR IN Gm Alarm Button DC 6 36v Fig 2 9 Alarm Input Connection Mobile DVR Alerter Fig 2 10 Alarm Output Connection User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 3 Operation Guide 3 1 Wire Control No Name Description OOO 1 POWER Reserved gt Numeric Input number upper and lower case symbol and Chinese character 1 Enter the edit state and then delete the character in the front of the cursor 2 Switch between Y and x in the status box 1 Switch between input methods Number English Chinese Symbol 2 Display or hide the channel status in the preview interface e rec Manual Recording Cs mo reserved OSOS SCS CS Co vow Resena OSOSOSC C S S sS s sS S S S S 10 menu switch from preview inter
8. Up shrink red pane dk Set whole screen as motion area PTZ Clear all motion areas A Save and return Image Setup menu ENTER Cancel setup and return Image Setup menu ESC Fig 5 16 Motion Alarm Handle Motion alarm policy Fig 5 16 1 Motion alarm schedule You can setup it in Motion Det gt Policy menu The setup steps are the same as external alarm in schedule please refer to section 5 3 1 2 Alarm linkage setup The alarm linkage setup includes recording handle method etc All the linkages can be set in Policy menu Fig 5 16 The linkage order of motion detection is Alarm in gt Trigger camera gt Recording Record setup please refer to section 5 4 The alarm handle method includes on screen warning audible warning upload to center trigger alarm out Note If you want to disable motion alarm area and motion alarm policy you just need to select the motion alarm sensitivity as Off 41 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 5 3 3 Video Loss Alarm When the video cable or camera has something wrong the video image is lost If you enable video loss alarm in such case DVR will make alarm In Image Setup menu select Handle in Signal Loss list Enter Policy menu to setup alarm schedule and handle methods The steps please refer to section 5 3 1 5 3 4 View Tampering Alarm If you enable this function when someone
9. Video stream and other is Video stream only If you want to record video and audio please select Audio amp Video option otherwise you can select Video option to record only video O Resolution The higher resolution is the clearer the image is The resolution options from low to high are QCIF CIF 2CIF DCIF 4CIF O Bit Rate Type There are two options Variable and Fixed The main features of Variable bit rate is it can maintain the image quality under the max bit rate In this case DVR can save HDD usage and network bandwidth If you select fixed bit rate DVR will use the fixed bit rate to compress image O Max Bit Rate The max bit rate selection has relations with resolution If you select high resolution you must select high bit rate For CIF resolution the typical max bit rate is 384K 768Kbps It is better to select the proper max bit rate based on the camera background and image quality requirement O Image Quality If you select variable bit rate type you can define image quality There are 6 options Highest Higher High Average Low and Lowest High image quality needs high bit rate size O Frame Rate Frame per second For low frame rate you can select low bit rate size 5 4 2 Pre Record Time and Post Record Time Pre Record Time When you enable motion detection recording or external alarm recording you can define prerecord time MaxPreRecord is to save all data in Pre Record buffer The Pr
10. again please disconnect KEY and reconnect it before booting the device 2 When booting the DVR beyond the auto on off time if there is no operation or user login in 5 min the device will auto halt 5 8 2 GPS Setup DS 8104HMI M supports build in GPS module When using the DVR with GPS module please connect antenna correctly details please refer to section 2 3 When receiving GPS signal it starts positioning function Note To ensure the GPS module works effectively please put the antenna on car roof or under windshield glass and make sure it is not be shielded O Time correct yY means the GPS time correction is enable You can choose the corresponding time zone The default time zone is GMT 08 00 Range GMT 12 00 to GMT 12 00 When the GPS signals are received the system will correct time every 5 mins O Speed Unit Max Speed Speed Unit and Max Speed is used to control the vehicle s speed by GPS information You can set a maximum speed and setup warning handle method in Exceptions menu When the vehicle is over speed the DVR will trigger the alarm Please refer to section 5 7 The speed unit has two options KPH MPH The default max speed is 100KPH and 62MPH this can be modified O Display Channel You can set whether the GPS information display on each channel y means the selected channel will display the GPS information including the latitude longitude speed of the vehicle Please refer to s
11. and preview the corresponding camera Press PREV you can switch the preview layout 4 3 User name and password Note When DVR is delivered from factory there is only one default administrator named admin and password is 12345 The administrator s name can not be modified while the password can be modified Please change the default password to ensure the data security The administrator can create 15 users and define 24 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 their user rights Modify password for the users created by admin For example a user named user The method of adding and deleting user please refer to section 5 1 2 please modify the password as follow Step 1 Enter the main menu and select User icon Fig 4 2 Step 2 Input the new password and confirm it Fig 4 3 Fig 4 2 Fig 4 3 25 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 4 4 PTZ Control Note The user must have the PTZ Control right Under the main menu mode press the PTZ to enter the PTZ control interface PTZ control keys description Direction control keys a Y 4 P ZOOM control keys ZOOM ZOOM FOCCUS control keys FOCUS FOCUS IRIS control keys IRIS IRIS Adjust preset keys REC SHOT three numeric key example REC SHOT 001 means call preset 1 Auto control key PLAY AUTO Exit the PTZ control operati
12. pole of vehicle battery and supply high signal as in Fig 2 4 2 Negative pole ignition switch ignition switch is connected to the negative pole of vehicle battery and supply low signal as in Fig 2 5 Ignition Switch Fig 2 4 Positive pole ignition switch Fig 2 5 Negative pole ignition switch Mobile DVR 2 5 1 Connection for Time Delay Shutdown Connect DC and DC to power supply battery positive and negative poles connect KEY interface to the vehicle ignition switch for DVR function of vehicle ignition startup and time delay shutdown There are two kinds of vehicle ignition switch 1 Connection of Positive Pole Switch Fig 2 6 Connect the DC IN of DVR to the positive pole of vehicle batteries Ignition Switch Connect the KEY of DVR to the vehicle ignition switch Positive Pole Connect the GND and KEY of DVR to the negative pole of vehicle batteries Fig 2 6 KEY connect with positive ignition switch 14 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Mobile DVR 2 Connection of Negative Pole Switch Fig 2 7 L AA Connect the DC IN and KEY of DVR to the positive pole of vehicle batteries Connect the KEY of DVR to the vehicle ignition switch Connect the GND of DVR to the negative pole of vehicle batteries Ignition Switch Negative Pole After KEY connected to the switch when switch on the DVR will start up with the vehicle
13. send information to that host IP This is reserved e Download Server IP when you use wifi or other network to upload recording files you need to set the download server IP O Wireless Modem It includes None CDMA EVDO WCDMA the default option is None When user use internal wireless module or connect the external module with USB to login the remote server it is necessary to setup the modem according to the wireless module Note 1 The items with means LAN configurations If you want to communicate in different network segments you need to set gateway 2 The bandwidth of every channel please refers to the Max bit rate setup of section 5 4 1 5 6 PTZ In PTZ menu you can setup the PTZ parameters and G mouse mode Fig 5 21 PTZ parameters include RS 485 parameters protocol PTZ address preset point sequence and cruise G mouse mode only has one parameter bit rate Firstly you need to select one camera the other parameters are as following RS 485 parameters Including baud rate data bit stop bit parity flow control etc These parameters must be the same as those of PTZ Protocol O PTZ parameters The PTZ protocol of DVR includes Hikvision Pelco p Pelco D SAE YAAN Samsung Howell Panasonic Philips etc The PTZ address in this interface should match the dialed address on PTZ Oo Preset setup Preset is using one number to represent camera s position zoom focus and iris One device has 128 preset point
14. sub menu Press Confirm to save parameters and return to parent menu Press Cancel button to cancel and return to parent menu The button in grey means it can be operated only after it is enabled Exit Menu You can press ESC to return to previous or preview interface also press PREV to return from menu to preview interface 3 3 Input Method In the submenu interface if entered the edit mode there will be an item at the bottom of the screen you can input the characters in the edit box by pressing Numeric Keys on the IR control If you want to input English i e uppercase just switch the input method to Uppercase by pressing A until the item shown as follow then you can input uppercase in the edit box with Numeric Keys buttons on the IR control The same as the method of entering the letters in mobile phones Besides the following input methods are supported as well Lowercase and Symbol There are 24 symbols in all and divided into 4 pages for choice you can turn over the pages by pressing 0 on the IR control Note In this user manual the button on IR control is denoted as Button Name e g Playback denote playback button Enter denote enter The parameter in the menu interface is denoted as Parameter Name e g Name denote camera name edit box User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 4 Basic Operation Guide Note The user must have the ap
15. the Activity Frame stops at one icon you can press ENTER to enter the submenu of corresponding icon shown as Fig 3 3 For example move the Active Frame to Image icon press ENTER to enter into the secondary menu show as Fig 3 4 Take Image interface as an example to explain the menu and operation rules Each menu contains different kinds of items There is a small rectangular frame named Active Frame which is pointing to the selected item This Active Frame can be moved by 4 or P keys There are such kinds of menu items a Check Box Provide 2 options Y means enable and x means disable You can use ENTER or EDIT key to switch over b List Box Provide more than 2 options However only one of them can be selected You can use amp and to select one option For example on the right side of Select Camera there is a list box for you to select one camera c Edit Box This is for you to input characters Press EDIT key to enter into edit status you can input characters as following i Press A key to select number upper case lower case or symbols ii Use and BP keys to move cursor iii Use EDIT key to delete the character in front of cursor 21 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 iv Press ENTER or ESC to exit edit d Button Execute a special function or enter into next sub menu For example press Policy button to enter into
16. the PTZ you are using can support preset point sequence and cruise 46 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 i A 1 i i Rec Gru m e 2009 06 23 16 01 50 Fig 5 23 Fig 5 24 5 7 Exceptions The exceptions can be handled include Hard disk full Hard disk error illegal access IP address conflict network failure NTSC PAL differ and speed limit etc The parameters can be set in Exceptions menu Fig 5 25 You can choose an exception type then select the handle methods as following O Audible Warning DVR beep warning e Upload to Center Send exception information to center host PC Oo Trigger Alarm Output Trigger local relay output 47 Har dD skFul User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 You can select more than one handle methods For example if you choose exception type as HD Error you can select Audible Warning and Upload to Center When the HDD has an error the DVR will warning and the center host PC will receive a warning message Note Speed limit function need GPS user can set that in Mobile gt GPS 5 8 Mobile Setup Mobile setup is a special menu for mobile DVR Fig 5 25 including O Boot amp Halt control the power on off time of mobile DVR GPS GPS functions and parameters PPP Set wireless modem type and parameters WVS the parameters for login the wireless remote monitoring server iVMS
17. the parameters for login the IVMS7000 platform Fig 5 26 Mobile Setup 5 8 1 Boot amp Halt Setup In the boot amp halt menu Fig 5 27 you can setup the shutdown mode and time There are two normal modes 1 Halt Delay When the KEY interface of the device link with the vehicle s ignition switch you can delay halt by setup the parameters The connection method please refer to section 2 3 3 As in Fig 5 27 user can set a halt delay time which means the DVR will continuously working after the vehicle power off until exceeding the halt delay time The minimum delay time is O min the maximum delay time is 6 hours The recommended period is between 30 min to 2 hours 2 Auto Work Fig 5 27 Boot amp Halt 48 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 If you have directly connected the positive pole of DVR KEY to vehicle battery Please refer to section 2 3 3 you can also select auto work function The auto work time can be set in Boot amp Halt menu The device will auto power on off according to the setup time O Auto Work V means start the auto work function Press EDIT to switch O Date the auto work setup is set by day you can copy the schedule to the other days Oo Period 1 Period 2 you can set two auto work periods for one day The periods cannot overlap O Copy to Copy the settled time can be copied to other days Note 1 After auto halt of device if user need to boot it
18. when switch off the DVR will shut down within the preset delay time More information on the time delay shutdown function can be found in section 5 8 1 Note Please contact the vehicle battery manufacture for the information on the voltage polarity Fig 2 7 KEY connect with negative ignition switch Mobile DVR 2 5 2 Connection for auto power on off Connect DC and KEY to the vehicle batteries positive pole and DC and KEY to the vehicle batteries negative pole for the DVR auto on off function The connection is as Fig 2 8 The settings details please refer to section 5 8 1 DS 8104HMI M XX series mobile DVR working consumption is less than 10W If you need a long auto working time please considering standby power supply according to the conditions Fig 2 8 KEY connect with vehicle batteries 15 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Note 1 When testing the DVR please refer to the power connection When the basic two power on conditions are met the DVR will work 2 To make sure the DVR can power on normally the power consumption should be more than 36W the working voltage is DC 6V to 36V 2 6 Alarm Output Connection Guide Alarm Input connection DS 8104HMI M XX series mobile DVR is applied high and low level signal to trigger the alarm input DC OV to 5V is low level signal DC 6V to 36V is high level signal To avoid misidentification signal between DC 5V to 6V will not be handled
19. 2 4 SIM UIM Card Installation When the DVR supports 3G function please follow the steps below to install SIM UIM card 12 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 SIMUM SIM UIM SD SD 1 Use the L screwdriver in 2 Then you will see the SIM 3 Press the yellow bar on the right of accessories box to twist off the UIM socket Indicated by red SIM UIM slot as shown on the left screws on the cover of SIM SD frame and SD SDHC socket figure to pop up the card as shown card Indicated by blue frame on the right figure 4 Extract the board and put 5 Insert the board to the slot 6 Reinstall the cover of SIM SD slot the card on the board and connect the 2 antenna 2 5 KEY Ignition Switch Connection Note 1 The basic two power on conditions for mobile DVR 13 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 1 Power supply interface has correct power connection 2 KEY interface has correct power connection In practice please connect of DC IN to vehicle battery and KEY to ignition switch or batteries the details please refer to the below connection figures 2 Please make sure that the positive pole of DVR power line connects the positive pole of vehicle batteries with the fuse 3 There are two kinds of vehicle ignition switch connection positive and negative connections 1 Positive pole ignition switch ignition switch is connected to the positive
20. 32 e Management locking ensures the security of key information e Pre allocation and low seeking technology ensure recorded data be effectively scanned e SMART e Cycle and non cycle recording modes e Support USB 2 0 recordings backup and clip Preview and playback e Portion or whole video mask e Portion or whole video mask alarm e Playback modes fast forward slow forward and single frame Search by recording type and time e Indication of recording and alarm status Alarm e Support speed limit alarm e 7 ch level signal alarm input and 1 ch reserved pulsing signal alarm input 2 ch alarm output e Choice of alarm types motion detected mask video loss and sensor input e Alarm schedule setup e Exception alarms configurable such as Hard Disk error and video format conflict Security e Customizing authority for operators by the administrator Support multi administrators more flexible security management e Channel based authority for remote preview and playback and local playback e A supper user with user name admin password 12345 by default Network e TCP IP based e Wireless comfortable compression technology e Software for alarms e g triggered signal exception and GPS alarm User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 e Audio preview and screen capture at client software e PPP enabled Client developing e Network protocol provided for platform system development e SDK provided for client devel
21. D volume Unit GB a TIN Unit Hour UN Unit Hour OS TIT Unit Hour 1 Unit Hour E a oO 1136 E FO OOO O O e a E A rs Cao oo oo a a EEE TO 10 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Declaration Recording time may be not so precise it is just for reference and we will not take the responsibility for this HDD installation steps UN 1 Please prepare all the tools 2 Firstly open the HD Lock with 3 The HDD bracket is fixed with and materials 2 5 inch SATA HD the key and loosen the screw wire rope Each side has a gap for anti static gloves HDD Lock key alone the anti clockwise Then HDD installation cross screwdriver HD screws pull out the HD box with uniform force 5 Please wear antistatic gloves 5 When insert the whole HDD 6 Put in the second HDD on the Carefully put in the first HD on please gently push it into the bracket PCB face up aim at the the bracket PCB face down aim under position HDD interface and insert it at the HD interface and insert it tightly 11 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 7 After inserting the second 8 Install the HD screws and 9 After the HDD installation HDD face the HDD connector to fasten the HDDs 4 screws per push in the HDD box and screw the socket on bracket and HDD follow the order on the up Don t forget to lock the tighten it figure HD Lock
22. DS 8104HMI A XX Embedded Mobile Net DVR User Manual V1 20 00 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Statement Please kindly note and understand that there may be misprints and technically inaccurate description The contents of this manual are subject to change without notice from time to time accompanying with the release of new version The listed products or programs will be improved or renewed whenever necessary Tips for users e Please install the DVR in well ventilated places e Please make sure the DVR work in the allowed range of temperature and humidity e The dust board will cause a short circuit after damping Please dedust regularly for the board connector chassis fan etc with brush e Please select the SD card manufacturers recommended SD which can meet the demand of DVR long time reading and writing large amount of data User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Table of Contents Production DESC A PU dato 5 LI A hata Re suet A one ie sages ado oluec tame aca ned aucan same Saeed oluiaa anes nea haa saeaa samen amnnae plus ceueeesanee eruetsamed wnosee ehumasaneteiaaue a 5 LZ MEE C EVN S scsi tcctesecs teas css se T nlc ca ic oases clare caste mete talib ca cco carina coca a et eee carseat came N 5 Stadion Mel ic o ios caia 8 Ak Checkdeviceand accEs SOM ia 8 22 Interface Descrip ace O a a a soap encase aa a sane same S 8 Dict HODDIAStala ON tte 10
23. N LAN Server IP input the WVS server static WAN IP Port should be as same as the client port of server the default is 5660 Login id and Login Psw the id and password assigned by the manage system you can get these from the manage system The ID is beginning with 1 and has 9 numbers 2 iVMS login settings The VMS 7000 series platform login interface is shown in Fig 5 31 Server IP input the IVMS 7000 center server static WAN IP Port connect port between DVR and center server the default is 7660 Login id the ID assigned by the server you can get these from the VWMS7000 server Please add the ID in iVMS7000 management center before using The setup of the server login parameters will become effective after reboot When the device connects to Fig 5 30 wireless network successfully it will login the central manage center automatically and show online status Then user can preview the video via client server Note 1 WVS platform is priority If you want to login iVMS platform please set WVS platform IP address as O 2 Considering the network bandwidth will affect the video transmission when preview with sub stream at client 3 channels are maximum This is valid for both iVMS platform and other client software Fig 5 31 51 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 6 Utilities The Utilities menu is used for day to day management and maintenance of DVR Including
24. Time Alarm Out Schedule Copy to Alarm Out Multi cast IP Http Port Network DNS IP Alarms Remote Host amp Port Download Server Exception Type Exceptions Handle Method Audible Warning Upload to Center Trigger Alarm Out PPPoE Camera Preview Mode Baud Rate Data Bits Stop Bits Parity Switch Time PTZ Flow Control Protocol RS232 Reserved Preview Audio Preview PTZ Address Preset Sequence Cruise Display Delay Layout 19 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 tame S o S S Boot amp Halt GPS PPP WVS IVMS Add Del User Password amp Verify Mobile Default amp Set Right 3 2 2 Menu Operations You can enter the menu interface by using IR control Press MENU button to enter the menu interface Press PLAY button to enter the playback interface Press REC button to enter the manual record interface Press PTZ button to enter the PTZ control interface Note Password is required and the default user name is admin password is 12345 20 Utilities Save Parameters Restore Parameters Upgrade HDD Stop Alarm Out Reboot Power Off View Log System Information User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Fig 3 3 Fig 3 4 There is a rectangular box in the main menu interface which is referred to as Activity Frame you can move it from one icon to another by pressing or E on the IR control When
25. W keys to select switch time There are many options including 5 Seconds 10 Seconds 20 Seconds 30 Seconds 1 Minutes 5 Minutes and Never If you select Never the preview image will not be switched automatically For example if you select 1 Screen preview mode and 20 Seconds switch time DVR will cycle display 1 channels image every 10 seconds O Audio preview If you need audio preview please use ENTER or EDIT to enable audio preview as Y If not please set it as x O Alarm display delay You can setup the display delay time of switching to the alarm channel by using dl Jor W keys to select a time in the Display Delay list The options have 1s 25 35 4s 5s 6s 7s 8s 9s and 10s For example if you select 4 Screen preview mode 10s alarm display delay time DVR will display 4 channels when there is an alarm from camera 1 the screen will switch to camera 1 after 10 seconds Oo Preview layout setup There is a square frame divided into many windows If you select 4 Screen preview mode this frame is divided into 4 windows Each window represents one camera You can move Active Frame among the windows There is one bar under the square to display the default preview order of all cameras To change the order you can move active frame to the first small window and press numeric keys to input camera index
26. ZA SIN WAN asta HON read 12 25 gt REVIEntion gt Witen Connect i ica 13 25 L lt CONMECUON TOR Time Delay SNULIO Wir AAA AAA AAA AAA AAA AT AA 14 252 Connection torauto pOWer on Of tn AAA ia 15 26 Alarm OUtput CONNECHON GUIAS Lara AAA AA AAA Ai 16 Operi Uon GUI ir a 17 3L MRE CONTO LA AA AS AAA AAA ASADA T 17 32 Mena Describe Ai 19 32l AMENA Starr 19 S272 Meni ODE AUN dana 20 gt INPUEMeSINO det E E E O EAEE E 22 Basic Operation GUIE esae N A E E E E 23 BA POW E OR ainia 23 Ez PEE AON a A E oan 24 43 Username and pass WOrO isie A AA AAA AAA AAA A 24 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 4A AE A a A A SP ne ee ee 26 E MA SRR rte Rs E A Eo oe 26 PO RIID ICKE em Ngee Se Pe Ee ee ee 27 AT BACK RECOL GCC NOS as ors o ita 29 AD Ae USB o o bn O 29 A AD A e A 30 Ads Backuo ENE EIAN ACK aci dei ii 30 Parameters SEUD QUA E o a A 32 Did BASIC SEINE oria o a a eamasee neuen cone Secuane sata coaehanaausenemt name eetors 32 Dade AdMiM rnor and PASS Words dea 32 S142 Aduana CUS I Ge a A A eens suisse gu siete iia 33 S1 UNEN an ea DD a eee 34 5 2 OCA Prev WS CUIDA AA inde AAA AAA AAA A 35 SAL WCCO QUtpUt tandai Chests sees asa seat tw stead dese a tps aaa 35 LA Z x SOROS SAV CN CEU DA AAA snc osc asia E EEEE 35 I2 USD CUP aa a 35 S24 Vide Parameters o UD AA A AAA AAA AA AA AAA AA AA AA aces duitiecds 36 I2 Mas ers Seti ana 36 2O PreVEWPTODOIC S cisse o S ias 37 SS ANSE a o A EA er rere
27. arameters Note If any network parameter is modified you must save and reboot DVR to make it into 11C Type 1OM 100N Auto effective The parameters can be setup in Network menu Fig 5 20 O NIC type Default is 10M 100M Auto the order options are 10M Half Dup 10M Full Dup 100M Half Dup and 100M Full Dup o IP ThisIP address must not be conflict with other IP If there is DHCP server in network you can set IP as 0 0 0 0 save and reboot DVR In reboot process DVR will search the DHCP server and get one dynamic IP address If DVR uses PPPoE function also DVR can dialup into internet and this item will display the dynamic internet IP address Oo Port Network access port number must be from 2000 to 65535 the default port is 8000 O Mask This is sub net mask Fig 5 20 44 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 O Gateway when the mobile DVR connects to server through a wireless router or communicates in different network segments you need to setup the gateway IP O Multicast IP it is one D class IP address among 224 0 0 0 to 239 255 255 255 We suggest using 239 252 0 0 to 239 255 255 255 If you do not use multicast function you do not need to set O Http Port the port is for IE browser The default value is 80 It can be modified O DNS Server reserved O Remote Host IP and Port If you set this IP and Port when there is an alarm or an exception happened DVR will
28. blocks the camera spitefully DVR will make warning alarm Tampering alarm includes area setup alarm schedule and handle methods The setup can be done in Image Setup gt View Tampering gt Area and Policy The default is Off there are 3 options low Normal and High Select one of them will active Area and Policy Enter into area setup interface the setup methods are same as that of mask area setup Only one view tampering area can be setup Please refer to section 5 2 5 Enter into policy setup interface to setup alarm schedule and handle method The steps please refer to section 5 3 1 Select Off option for View Tampering you can disable the view tampering function 5 4 Recording Setup In the Recording channel Configuration menu you can setup record image parameters schedule pre record and post record Fig 5 18 42 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Before the recording parameters you need to decide whether Overwrite or Stop Recording when HD is full If you select Overwrite when HD in DVR are full DVR will overwrite the earliest recorded files and continue recording If you select Stop recording when HD is full DVR will handle it as HD Full exception please refer to chapter 5 17 for exception menu 5 4 1 Recording parameters description O Stream Type There are two options one is Audio amp
29. brown 8 brown 8 brown Straight line connection Cross line connection 58 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Appendix C Specifications Video Input 4 ch 1 0Vp p 75Q PAL NTSC adaptive PAL 1 16 25fps NTSC 1 16 30fps Audio Output 1 ch Linear 600Q Stream Type Video Video amp Audio Alarm Input 7 level inputs 1 impulse input Alarm Output 2 alarm outputs Wireless Network Built in WCDMA or EVDO module optional GP Built in high sensitivity GPS module HDD Interface Dual 2 5 inch SATA SSD HDDs Hard disk backup USB Backup 59 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 10 95 236 W x73 H x210 D About 3Kg Device Control IR remote control 60 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Appendix D FAQ Q Why a new machine has di di di di voice warning after boot A Reason1 there is no HDD in DVR Reason2 the HDD is not initialized Reason3 HDD is broken If do not need the HDD please go to the exception settings menu disable the voice warning of Hard Disk error as x If it has HDD please go to HDD management menu and initialize the HDD If the HDD is broken please change a new one Q Why the monitor has no response when operating the remote controller A The correct way of using the remote controller is make sure the battery has been installed correctly before use the remote control
30. ceiving the device Fig 5 2 Step 1 Open the main menu and enter User menu Fig 5 2 Step 2 Use W key to choose a user name 32 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Step 3 Use dl B key to move Active Frame to password edit box input the new password Move Active Frame to Verify password edit box input the verify password Then choose the Confirm button the password will be saved and taken into effective Note When the Active Frame on the user name please use dk W key to choose one user use 4 key move the active frame to other options If password and verify password are not same a warning message box will be appeared Suggestion To facilitate the operation of first time setting you can disable the password in the Display menu Fig 5 6 Setting the Require Password status as x Note For security reason it is better for you to set Require Password as Y after completing all the setup 5 1 2 Add and Delete User Select Add in User Management interface to add new user in pop up Add menu and Fig 5 3 return User Management menu to define password and rights 15 User MAX i User rights description Local Rights Local rights are for local operation such as the operation using IR controller and RS 485 keyboard PTZ control Locally control PTZ Record Manual start stop re
31. cording Parameters Setup Locally setup the DVR parameters Log Locally view the log on DVR Utilities Locally upgrade firmware format HDD reboot DVR and shut down DVR etc Playback Local playback and backup the recorded files Fig 5 4 33 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Remote Rights Remote rights define the rights of operating by IE or Client Server O PTZ control Remote control PTZ O Record Remote manual start stop recording O Parameters setup Remote setup the DVR parameters O Log Remote view the log on DVR e Utilities Remote upgrade firmware format HDD reboot DVR and shut down DVR etc O Voice Client talks with DVR O Alarm Remote control DVR alarm output O Local video out Remote control DVR video output O Com control DVR RS 232 transparent channel function Oo Preview Network live preview Oo Playback Remote playback download the recorded files on DVR MAC address This MAC address is not the address of DVR but the PC that will access DVR If you setup this MAC address only the PC with this MAC address can access this DVR At PC end in DOS prompt you can use ipconfig command to get the PC MAC address 6 bytes Delete user In User Management interface you can select one user then move active frame to Del button press ENTER in the pop up confirmation dialog press Confirm button to delete the selected user and re
32. des motion detection area schedule and policy In Image Setup menu you need to set detection sensitivity before the other parameters There are 7 options from O the lowest to 5 the highest and Off Motion area setup Move active frame to Area button on the right of sensitivity list box and enter into Motion Area Setup interface The whole screen is divided into 22 18 panes NTSC 22 15 There is one yellow panel on the upper left side Firstly move the yellow pane to your hope position and press EDIT key the yellow pane will be turned into red then you can use to expand downward amp to shrink upward to expand rightward 4 to shrink leftward After you make sure the red mask area press EDIT key to save the motion area Press ESC key to cancel the motion area Fig 5 15 Motion Detection Area Setup 40 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 You can use PTZ key to set the whole screen as motion area and multi motion areas can be defined Press A key to clear all motion areas The minimum area is one panel After you setup the areas press ENTER key to return Image Setup menu The keys used to setup motion areas are following Move yellow pane to any position dk Y 4 P Yellow pane and red pane switch key EDIT Yellow pane and black pane switch key EDIT Left shrink red pane 8 Right enlarge red pane Down enlarge red pane
33. e Connect to wire remote control or IR remote repeater when required Interface 7 RS 485 T T R R PTZ Connect to PTZ 3 GG Alarm Input GND The GND corresponding to alarm input G 5V G 12V Power Output 5VDC 2A 12VDC 2A power output for external devices 9 RS 232 RS 232 Connect to RS 232 devices e g modem PC and etc N k 10 LAN oe Connect to network e g router switch hub and etc Interface 11 USB USB Connect to USB devices e g flash disk USB HDD 10 SIM CARD SIM card Socket SIM UIM card socket for 3G the DVR should support 3G SD CARD SD SDHC Socket Reserved SD SDHC card socket 13 ANT1 ANT2 3G Antenna Connect to 3G antenna ANT1 is main antenna ANT2 is aux antenna 4 pin definition of aviation connector User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 DC 12V Figure 2 2 Input Aviation Connector Figure 2 3 Output Aviation Connector 2 3 HDD Installation Note 1 Tips for HDD purchase please choose recommended high quality 2 5 HDD from creditable provider e g Seagate Hitachi and etc that should be comfortable for longtime and frequent read amp write 2 HDD should be formatted after the installation or there may be HDD error with alarm Format method please refer to section 6 4 3 With the default configuration the corresponding recording times for different Volume are Recording time Bit Rate Recording time Bit Rate Recording time Bit Rate Recording time Bit Rate HD
34. e Record time is related with bit rate The lower bit rate the longer Pre Record time is The actual time maybe have deviation Post Record Time This is the DVR continue recording time when external alarm or motion alarm is stopped The time can be setup according to the requirement 5 4 3 Record Schedule Setup In recording menu enable record function Y flag press Schedule button to enter into recording schedule menu Fig 5 19 O Day The recording is settled by day If everyday has the same schedule you can copy one day schedule to the other days 43 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 O All Day Rec Type If you need to record 24 hours you can enable All Day option and select a record type O Period If you do not need record all day or you need to record different types in different period there are 4 time periods for one day and each time period can select start time stop time and different record type O Copy to Copy The setup schedule can be copied to other days Note 1 If record type is Motion Detect you must setup Motion Detection in order to trigger motion recording Refer to section 5 3 2 2 If record type is Alarm you must setup Alarms in order to trigger alarm recording Refer to section 5 13 3 The time period is among 00 00 24 00 5 5 Network Parameters Fig 5 19 If you want use network to access DVR you must setup network p
35. e is 10 29 on 2008 8 7 1 Playback multi channel backup files MVA software can be used to playback multi channel backup files If DVR has GPS function the recording file can be playback with the position displayed on the map The details please refer to the MVA user manual 30 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 2 Playback one backup file Please use our company s player which can be found in the CD to play the file You can also download the plug in from our website to play it with other software 31 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 5 Parameters Setup Guide Note Only the users have Parameters Setup right can set the parameters You must reboot the DVR to make the new parameters take into effective when the following parameters are modified and saved Fig 5 1 Other parameters do not need to reboot O Any network parameters Stream type resolution and record schedule External alarm sensor type Fig 5 1 View tampering alarm schedule Video lost alarm schedule Motion detection alarm schedule External alarm schedule Login server parameters Wireless network parameters 5 1 Basic Setting 5 1 1 Administrator and Password When DVR is left from factory there is one default administrator The name is admin and password is 12345 The name cannot be changed while the password can be For security reason please change the password after you re
36. ection 4 2 Fig 5 28 49 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 5 8 3 PPP settings For DS 8104HMI A there are 3 options of wireless modem including WCDMA and EVDO cdma2000 In this menu user can set the parameters of the build in module for the wireless network transmission The menu is shown in Fig 5 29 The default option is None the module type can be distinguished by the device name DS 8104 HM A GW WCDMA DS 8104 HM A GE EVDO Before enable wireless module please get the information of the network including APN number username and password from ISP Before parameters setup please connect antenna and keep it vertical Select the correct module type and input corresponding parameters in PPP menu After rebooting the device will dial up automatically and get the WAN IP Fig 5 29 Note When setting dial up parameters user needs to input numbers letters and symbols The input details please refer to section 3 3 5 8 4 Server Login Setup DS 8104HMI A XX series mobile DVR can support WVS platform and iVMS platform the corresponding login parameters have to be set before the device login the wireless network server in WVS menu and VMS menu 1 WVS login settings 50 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 The WVS login interface is shown in Fig 5 30 Used For there are 4 options for the network environments CDMA EDGE GPRS 3G WLA
37. ee eee eee 38 SoL JEXternal Alani inputiana Relay OUTPUT esurire e EA E E 38 592 Moon Detection Alar tati ii 40 SRo Vdeo Loss Ala bli taba aii 42 ee NOME iOS AM doses 42 54 RECOTdINE SEDA A E nee ee eee ee 42 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 54 1 Recording parameters describo i124 tose ies Siena ea E a a tat lece ds 43 541 2 Pre Recora TIme ana POSt R ECONO TIN Orein T aesied oa scare isa 43 SS Record Enea ue CU andas 43 Did INCUWORK Par o sica 44 S0 A A O A a 45 A O 47 Deo IMODE Sets aio aici 48 SeA BOCS Hate tU a coa 48 J02 O A A O 49 So CRE SOLANO SS A aa 50 o OV FEOS II O re oia 50 E UM e doo 52 o Save Para meters oca A NAAA 52 OZ Restore Parametros AAA a agen sees 52 A A a e o O E E O O A 53 64 Hara DISManaemen tinas A A ee er eon a ee 53 65 A A un e OOO sana snd ca T ie danas te 54 GO SIRO Be ag Sa Bi cae ses siete a apes ne ett Sie Dev ec wk Pow alan Sede ca tc oe adele ed emcee a eee ee 54 GF ROWER Dias dada 54 Do VOW LOO o use waa eases atwuca E Nadia 54 67 SVSCOM IMT ORIN ARON cesen aiii 55 Appena A HDD Capacity Calculator iii 56 Appendix B ETHERNET Connect Cable Made Method scsi 58 APPENA COP CANCION aa A A don 59 Appendix DFA imisi AAA TEA DAA AREA AA E 61 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 1 Production Introduction 1 1 Overview The DS 8104HMI A XX Embedded DVR is an excellent product designed for veh
38. face to menu interface 17 17 14 15 16 18 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Direction Keys Up WN Down VW Left Right gt 1 In menu mode moving the activity frame by press amp gt and selecting the data items by press MM amp WV 2 PTZ Position Control 3 Playback fast slow forward and rewind 1 Confirm when in menu mode 2 Switch between VY and x in the status box 3 Pause when playback 13 PTZ Enter PTZ Control mode ESC Cancel and return to previous menu Reserved 15 16 F1 Reserved SO L 17 rae Adjust Iris focus and zoom Control 18 F2 Reserved SS 18 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 3 2 Menu Description 3 2 1 Menu items Item Option Item Option Item Option Unit Name Select Camera Device ID Name amp Position Require Password Brightness Contrast Hue Screen Saver Saturation Video Standard OSD amp Position Enable Scaler Privacy Mask Menu Transparency View Tampering DST Signal Loss Date amp Time Motion Detection Copy to Camera If HDD full Overwrite Stop Recording Stream Type Resolution Bit Rate Type Max Bit Rate Image Quality Frame Rate Enable Recording Pre Recording Time amp Post Recording Time Copy to Camera Display Image Recording asic network parameters e g ay Alarm In amp Type Alarm Handling Copy to Alarm In Alarm Out amp
39. iCom Stop Stop Voice Talk Net Upgrade Net File Play Net Time Play Net PTZ and so on For alarm major type the minor type includes External Alarm In External Alarm Out Motion Detect Start Motion Detect Stop View Tamper Start View Tamper Stop and so on For exception minor type the minor type includes Video Signal Loss Illegal Access Hard Disk Error Hard Disk Full IP Conflict DCD Lost and so on Search by time Select By Time input start time and stop time After finish searching DVR will list the matched log information 2000 items maximum Search by type amp time Select By Type Time input major type minor type start time and stop time DVR will list the matched log information Note After the DVR listing the matched log information you can check more items by pressing Morelnfo including panel user net user host address parameter type channel No Hard Disk No alarm in and alarm out You can use Page No to change page 6 9 System Information Press System Info icon you can get DVR system information includes Unit Name Device Model Serial Number Firmware Version and Encode Version Please provide accurate and total system information when consult with supplier Fig 6 8 55 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Appendix A HDD Capacity Calculation Calculate total capacity needed by each DVR according to video recording video record
40. icle surveillance It supports local recording of HDD driving information recording voice talk GPS wireless alarm triggering etc This mini mobile DVR with lower power consumption is very easy to install The chassis is made from aluminum and designed according to the requirement of thermal dissipation It can work without fans and be prevented from dust water and rust Key features Support 2 5 inch pluggable HDD reserved SD SDHC card socket Build in 3G wireless network module Support GPS Support G sensor for driving behavior data connection Shutdown delay and auto power on off Ignition power on and power off delay Specific platform for vehicle remote monitoring 1 2 Key Functions Compression technology e 4 ch PAL NTSC Vin H 264 based Support variable bit rate and frame rate and configurable video quality and data rate e Each channel supports 4CIF 6fps DCIF 12fps 2CIF 15fps CIF full frame and QCIF full frame encoding e 2 chAIN 16kps OggVorbis standard real time compression e Video amp audio or single video stream supported e Dual stream local storage and wireless network transmission can be set separately User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 e Video parameters dynamic setting e OSD and LOGO display Feature of local process Video recording e Variety of recording models Schedule recording manual recording alarm recording etc e Support HDD storage e HDD file format FAT
41. ing type and video file storage time Step 1 According to Formula 1 to calculate storage capacity that is the capacity q ofeach channel needed for every hour unit Mbyte q d 8x3600 1024 1 i i In the formula d the bit rate unit Kbit s Step 2 After video time requirement is confirmed according to Formula 2 to calculate the storage capacity m which is storage of each channel needed unit Mbyte m q xh x D 2 l In the formula h The recording time for each day hour D Number of days for which the video shall be kept Step 3 According to Formula 3 to calculate total capacity accumulation q that is needed for all channels in the DVR during scheduled video recording C Ge m 3 1 In the formula c Total number of channels in one DVR Step 4 According to Formula 4 to calculate total capacity accumulation q that is needed for all channels in DVR during alarm video recording including motion detection 56 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 C dr gt m xa i l In the formula a Alarm occurrence rate For example According to the above formula if the bit rate type is FIXED for different bit rate the file size of ONE channel in ONE hour is Bit Rate Max TENI Bit Rate Max Sees Bit Rate Max TES Bit Rate File Size Bit Rate File Size Bit Rate File Size 96k 42M 320k 140M 896k 393M 128k
42. ion after rebooting please contact the supplier to repair 6 4 Hard Disk Management Check HDD work status Capacity Free space Stand by or not Normal status or not Format HDD Before formatting stop all recording After formatting you must reboot DVR otherwise DVR will not work normally Fig 6 6 53 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 6 5 Clear Alarm Out Clear the alarm output manually 6 6 Reboot Reboot DVR 6 7 Power Off Not available for mobile DVR 6 8 View Log After enter into the LOG menu you can check the log Fig 6 7 Press key on the front panel to view all the log this will list the earliest 2000 record log 8 items per page 250 pages Also you can select options to search Search by type Type is divided into Major type and Minor type Major type includes operation alarm exception and all The operation major type include Power On Shut Down Abnormal Shut Panel Login Panel Logout Panel Config Panel File Play Panel Time Play Local Start Record Local Stop Record Panel PTZ Panel Preview Panel Set Time Local Upgrade Net Login Net Logout Net start Record Net Stop Record Net Start Transparent Channel Net Stop Transparent Channel Net Get Parameter Net Config Net 54 Fig 6 7 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 get Status Net Alert On Net Alert Off Net Reboot BiComStart Start Voice Talk B
43. ist box use d F keys to move the scroll bar to the file press ENTER key to playback the file If directly press Play button after setting the channel record type and time section DVR will start to playback based on time section If DVR cannot find the matched files then a failure dialog will pop up as shown in Fig 4 7 At the bottom of image there is an information bar with the Volume Play Process Play Speed Played Time and File Total Time Fig 4 8 Playback control keys description O Display Hide information bar MENU Open Close sound PLAY under the mute mode x will appear on the bar Adjust play progress Backward Forward The unit is Adjust play speed Use dl to increase play speed use F to decrease play speed MAX 4x Pause Continue Press ENTER to pause continue playback If played frame by frame press ENTER to play one frame O Exit ESC Note 1 When the DVR is busy working if select high speed playback the actual speed will has some deviation non x 2 When the DVR is recording high speed playback may affect the recording N O VI DEO Exit playback In playback interface press ESC key to exit and enter preview mode In playback interface press MENU key to enter main menu press REC key to enter manual record and press PTZ key to enter into PTZ control mode Fig 4 8 Playback Image 28 User Manual of DS 8104HMI A XX Series Mobile Net
44. ler After the device power on ready press Device button input gt device code press ENTER Then you can control the device by pressing MENU If the device code is 255 you can directly control the device with this remote controller by pressing MENU button The default device code is 255 If it still does not work after repeating many times Please check the reasons 1 Check the battery s positive and negative polarity 2 Check the battery s power 3 Check the connected wire is in good condition After exclude all of above reasons please change a new remote controller if it still does not work please contact the supplier Q Why DVR cannot display GPS information after antenna connecting A Please check the following conditions 1 The GPS antenna is outdoor or out of car 2 The GPS antenna is not covered or blocked by other objects 3 When using for the first time please choose an open space 4 The GPS information display channel is set in GPS menu Press Device button input device code gt press ENTER Then you can control the device by pressing MENU If the device code is 255 you can directly control the device with this remote controller by pressing MENU button The default device code is 61 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 255 If it still does not work after repeating many times Please check the reasons 1 Check the battery s positive and negative polarity
45. n o m SavePara RestorePara Upgrade Hard Disk Stop Alarm Out Reboot Power Off View Log and System Info The Utilities menu is shown in Fig 6 1 6 1 Save Parameters Save current parameters to device FLASH this change will take effective after reboot Fig 6 1 Fig 6 2 6 2 Restore Parameters Fig 6 1 Restore factory parameters for DVR The IP address gateway port number and mask will not be restored Fig 6 1 Fig 6 3 Fig 6 2 Fig 6 3 Fig 6 4 52 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 6 3 Upgrade You can use this function to upgrade the firmware Please confirm the language is matched Press Upgrade icon in the pop up dialog you can select either FTP or USB upgrade mode Fig 6 4 If you select FTP mode you will enter into FTP Upgrade menu Fig6 5 In this method you need a host PC that is in the same LAN as DVR and the host PC starts FTP service Copy the upgrade firmware to the ftp server Input the ftp server IP and press Enter DVR will connect Fig 6 5 with FTP server through network and download the upgrade firmware file If you select USB mode please make sure you connect one USB flash memory with DVR and the firmware file is in its root directory Reboot after successfully upgrading the system will use the new firmware Note Upgrade failure will give rise to except
46. nd the device start up ready Note If the HDD is undetected or not installed there will be an audible warning from buzzer as the DVR starts up You can cancel the audible warning by changing the Audible Warning status in the Hard Disk Error option of the Exceptions submenu We suggest you to enable this warning function to make sure that you can get the working status 23 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 4 2 Preview The preview interface will show up after the device started up The date time channel name and GPS info Enable GPS function can be seen in the preview interface if you want to reset them please refer to the section 5 2 3 OSD Setup There are recording and alarm status of each channel displayed at the bottom of the screen The two kinds of status will switch over automatically which will hide or display by pressing A Icons Descriptions of Recording amp Alarm status O White NoVideo O White Videotost O Yellow Videolmpuee S O Yelow ViewTampering Pink ManualRecordings Pik Motion Detection amp Sensor Alarm Green Schedule Recordings Gren NoAlam Bue Motion Detection Recording O Blue MotionDetecti n 0 Red External Alarm Recordins red Sensor Alarm Press Numeric Keys buttons you can switch to the channel directly Press EDIT you can switch the channel in order
47. on press ENTER key to enter the backup menu Fig 4 10 Firstly select the Save Device and Camera V means the camera is selected press EDIT to switch x and v Secondly select Rec Type and set Date and Period Finally move the Active Frame to Start Backup and press ENTER to start backup If there is no file in the selected period after pressing ENTER will back to playback interface Note 1 The backup disk should be FAT32 if not please format it first Format method is after choosing the Save Device the Active Frame will on Format press EDIT to start formatting 2 If Device Error dialog Fig 4 11 pop up please check the device connection 4 7 2 HDD Backup Fig 4 10 Backup the files in a certain period User can directly push out the HDD bracket insert it into DS 1004HMI Mobile DVR backup device and use MVA Mobile Video Analysis software to playback and download recorded files The details please refer to the user manual of MVA 4 7 3 Backup File Playback Backup files naming rule Backup files will be saved in the file named with the DVR name Please refer 5 1 3 for the DVR name details The files can be searched by their names for example in a folder named CABX 5523 there is a file with name ch01 200808071029 mp4 that means this file is the record video of DVR named CABX 5523 channel 1 the beginning tim
48. on menu If you want to do the other operation such as playback manual record and so on you need to exit the PTZ operation menu Press the ESC button to exit and go back to the preview mode 4 5 Manual Record Note The user must have the corresponding right Press REC key to enter the Manual Record interface Fig 4 4 MOD Start Recording you can start corresponding channel recording by set Start Stop status as x or press Start All to start all channels recording Stop Recording you can stop corresponding channel recording by set Start Stop status as v or press Stop All to stop all channels recording Fig 4 4 26 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Exit manual record Press ESC key to exit manual record and enter preview mode Press MENU key to enter main menu Press Play key to enter into playback menu Press PTZ key to enter PTZ control mode 4 6 Playback Note The user must have Playback right Press PLAY key enter Playback interface Fig 4 5 Fig 4 5 Fig 4 6 27 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Playback operations In the playback interface you can set search channels record type time section and select Search button DVR will search and list the matched files Fig 4 6 If the matched files are more than8 you can use Page No to select page In the file l
49. opment e DEMOs with source code provided User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 2 Installation help 2 1 Check device and accessories Please check carefully according to the list inside once you get it 2 2 Interface Description DS 8104HMI A XX front panel is shown as below Note the descriptions are subject to the physical product 13 12 11 10 9 B A 9 Fig 2 1 DS 8104HMI A front panel User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 No Symbol Physical Name Description DC IN 1 Power Input Connect to DC supply DC 6V to 36V The power should be over 36W OT hod Details ol F KEY enim canta Connect to ignition switch or battery according to booting method Details please refer 1 to section 2 5 Standby Power l DC IN2 input Standby interface for DC IN1 the same connection as DC IN1 2 GPS antenas Connect to GPS antenna Interface E Video audio and 12VDC power output 4 pin definition 1 Video output 2 Audio a eee pu output 3 12VDC output 4 GND l Video audio and 12VDC power input 4 pin definition 1 Video input 2 Audio input 4 H1 CH4 1 Pan signal Input 3 12vDC output 4 GND 5 ALARM IN 1 8 Alarm Input 1 7 channels are high level signal triggered alarm input 8 channel is reserved ALARM OUT 1A 1B 2A 2B Alarm Output 2 alarm output 1A and 1B is a pair 2A and 2B is a pair R l 6 KB ena ea
50. propriate rights for basic operations described in this chapter The following Fig 4 1 are login prompt boxes In this box you can use di and F to select one username then press B to move to password After entering the password please press ENTER to exit the password box and press confirm to enter the menu If there is an alarm Fig 4 1 which means the input password mismatched the username If the mismatch happened three times the system will logout automatically Note admin is the administrator with the highest authority 4 1 Power On Note Please confirm that the power supply matches the working requirement of DVR and make sure the grounding is good Please make sure that there is a monitor connected to VOUT interface on the rear panel of DVR so as to operate the device with the visible menu After power on and switch on the ignition the device begin to start up the POWER indicator is turn green When Ready turn green means this device is ready to be controlled by IR control The initialization status of DSP will show up in the first row up the display or monitor if the DSP icon is marked with x it means initialization failed please contact the supplier in time The initialization status of HDD will show up in the second row if the HDD icon is marked with x it means the HDD is undetected or not installed You can control the device with wire control only if the Ready indicator is turn green a
51. s You can press Setup button on the right side of Preset item to enter Set Preset interface Fig 5 22 In this menu you can add adjust and delete preset points Note PTZ control and external alarm in can call the preset points Please refer to section4 4 and section 5 3 1 O Sequence setup Press Setup button on the right side of Sequence No tem to add cruise point and delete cruise point 45 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 ad 2000 06 23 16 00 37 Fig 5 21 The parameters of adding cruise point are Cruise No 1 to 16 Preset 1 to 128 please ensure the preset point has already been defined Dwell Time the dwell time on the preset point Dwell Speed the speed from one preset point to another point Note PTZ control and external alarm in can call the sequence Please refer to section 5 3 1 Cruise setup Cruise is remembering the track of PTZ movement This movement is manual controlled In PTZ menu press Setup button on the right side of Cruise item you can enter into Cruise setup menu to setup cruise and run the defined cruises Press PecCru button you will enter into PTZ control interface You can start controlling PTZ with direction keys press ENTER to save the operation track and return Cruise setup menu Press StartCru button to repeat the PTZ track until you press Stop button Note Please make sure
52. sequence is 16 and cruise is 1 Note One alarm in can trigger different channels preset point sequence and cruise but can only use one of them The order of warning on screen is Alarm in gt Trigger camera gt Warn on screen This can be setup by select On Screen Warning in Alarm In Handling menu If more than one alarm in or linked with more than one camera the display images will switch every 10 seconds until the alarm stopping 39 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 tl In Handle Method you can also setup Audible warning Upload to Center and Trigger Alarm Out The alarm in schedule is in Alarm In Handling menu Note The schedule is settled by day you can copy this to the other days The alarm in parameters can be copied to other alarm in channels in Alarms menu Alarm relay output setup In Alarms menu you can set output delay time The options are 5 Seconds 10 Seconds 30 Seconds 1 Minute 2 Minutes 5 Minutes 10 Minutes and Manual Stop If you select Manual option the alarm output will not stop until you press Stop AlmOut button in Utilities So the actual alarm output time is made up of alarm input time and this delay time You can set the alarm output schedule by entering Schedule menu from Alarms interface Fig 5 14 Fig 5 14 5 3 2 Motion Detection Alarm Motion Detection Alarm setup inclu
53. turn Fig 5 5 Please notice that admin is undeletable Fig 5 5 5 1 3 Unit Name and Device ID The unit name and device ID can be set in Display menu Fig 5 6 34 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 Unit name is the name of DVR it can be modified according to the requirement of monitoring For example it can be named as the car license number to facilitate the search of backup files Device ID is the ID for IR control The default device ID of DVR is 255 The device ID value is ranged among 01 255 5 2 Local Preview Setup 5 2 1 Video output standard The device supports PAL or NTSC video output The video input standard is adaptive You can modify video output standard to match video input in Display menu Fig 5 6 5 2 2 Screen Saver Setup If the user operates nothing for a period of time the device will return to preview automatically The screen saver is used to control the time This parameter can be set in Display menu Fig 5 6 The options have 1min 2min 5min 10min 20min 30min and NEVER 5 2 3 OSD Setup OSD is abbreviation of On Screen Display It includes displaying system time and camera name OSD setting include System time time format time display position camera name camera name display position etc 35 User Manual of DS 8104HMI A XX Series Mobile Net DVR V1 20 00 In Display menu you can setup DVR system date and time Fig
Download Pdf Manuals
Related Search