Home

TPL 80 / 82.5 Ticket Printer

1. 1B 34 n Name Set reset italic mode Format ASCII ESC 4 Hex 1B 34 Decimal 27 52 n Range 0 lt lt 1 48 lt lt 49 Description Turns italic mode on or off based on the following values of n n Function 0 48 Turns off italic mode 1 49 Turns on italic mode Notes The printer can print any character in italic mode When italic mode is turned off by setting the value of n to 0 or 48 the data which follows is printed in normal mode Italic mode can also be turned on or off using 1B 21 Note however that the last received command is the effective one Default n 0 Reference 1B 21 Example 1B 3D n Name Select peripheral device Format ASCII ESC Hex 1B 3D n Decimal 27 61 Range lt lt 255 Description Select the device to which the host computer sends data using n as follows Bit Off On Hex Decimal Function 0 Off 00 0 Printer disabled On 01 1 Printer enabled 1 2 RESERVED 2 RESERVED 3 RESERVED 4 RESERVED 5 RESERVED 6 RESERVED 7 RESERVED Notes When the printer is disabled it ignores all transmitted data until the printer is enabled through this command Default n 1 Reference Example TPL 80 82 5 3 42 CUSTOM 3 PRINTER FUNCTIONS 1B 3F n Name Cancel user defined characters Format ASCII ESC n Hex 1B n Decimal 27 63 n Range 32 lt lt 126 Description Cancels user defined characters
2. 80 82 5 Prints a bar code 3 2 3 PRINTER FUNCTIONS Com HEX Com ASCII Descrizione 1D 76 GS v Extended status request C 10 77 n GS wn Selects bar code width 1D E0 n GS 1n Enable disable automatic FULL STATUS back 1D E2 n GS n Reading number of cuts performed from teh printer 1D E3 GS Reading of length cm of printed paper 1D E5 GS Reading number of power up i In the table listed above the command marked with this symbol are defined only for the serial interface Given below are more detailed descriptions of each command 0A Name Print and line feed Format ASCII LF Hex 0A Decimal 10 Description Prints the data in the buffer and feeds one line based on the current line spacing Notes Sets the print position to the beginning of the line Default Reference Example 0B Name Vertical tab Format ASCII VT Hex 0B Decimale 11 Description When this character is received the paper forward feeds by n lines default value 10 This value can be modified by using the command 1B 7A When the printer is next initialized the default value is reset Notes Default Reference Example 0C Name Form Feed Format ASCII FF Hex 0 Decimal 12 Description If the buffer contains any characters these are printed and the paper forward feeds until the detection of a reference mark on the paper signalled by the
3. 1B FB Name Format Description Notes Default Reference Example 1B FC n Name Format Range Description Print graphic bank 608 x 431 dots ASCII ESC nxH xL Hex 1B FA n XH xL Decimal 27 250 n xH xL yH yL 0 lt lt 3 0 XH xL yL x 255 Prints graphic bank from flash or ram n selects the graphic source as follows n Function 0 Print ram bank 1 Print flash bank logo 1 2 Print flash bank logo 2 3 Print flash bank logo 3 XL xH x 256 specifies the starting dotline 1 431 yL yH x 256 specifies the number of lines to print If xL xH x 256 gt 608 the printer does not execute the command If xL xH x 256 yL yH x 256 gt 431the printer prints only 431 xL xH x 256 1 dotline 1B FC 1B FD 1B FE To print from ram bank dotline 100 to dotline 299 send 1B FA 00 00 64 00 C7 Transmit ram bank to serial port ASCII ESC nL nH Hex 1B FB nL nH Decimal 27 251 nL nH Transmits nH x 256 nL bytes of ram bank to serial port The size of ram bank for graphic printing is 640 horizontal dots 80 bytes dotline x 409 vertical dots 32720 bytes 16360 words 1B FC 1B FD 1B FE Transfer flash bank into ram bank ASCII ESC n Hex 1B FC n Decimal 27 252 n 1 lt n lt 3 Transfers flash bank into ram bank 32768 bytes n selects the bank as follows
4. ASCII ESC d n Hex 1B 64 n Decimal 27 100 n 0 lt lt 255 Prints the data the print buffer and feeds the paper n lines Sets the print starting position at the beginning of the line The maximum paper feed amount is 200 lines Even if a paper feed amount of more than 200 lines is set the printer feeds the paper only 200 lines Sets the default font ASCII ESC f n Hex 1B 66 n Decimal 27 102 n This command sets the default font The font currently in use is also changed n 01 Font 8x16 n 02 Font 16x24 n 03 Font 24x32 TPL 80 82 5 3 16 CUSTOM 1B 69 Name Format Description Notes Default Reference Example 1B 6D Name Format Description Notes Default Reference Example 1B 72 n Name Format Range Description Notes Default Reference 3 PRINTER FUNCTIONS Total cut ASCII ESC i Hex 1B 69 Decimal 27 105 This command enables cutter operation If there is no cutter a disabling flag is set and any subsequent cut commands will be ignored The printer waits to complete all paper movement commands before it executes a total cut Partial cut ASCII ESC m Hex 1B eD Decimal 27 109 This command enables partial cutter operation If there is no cutter a disabling flag is set and any subsequent cut commands will be ignored The printer waits to complete all paper movement commands before it executes a partial cut Copy ram b
5. Justification Left 2 Centered or Right With ESC POS emulation Char line A 43 B 60 columns or 60 B 76 columns A 45 B 64 columns A 64 B 80 columns With CUSTOM TPT emulation Font Size 25 col 38 col 76 col 26 col 40 col 80 col Q 24x32 16x24 8x16 24x32 16x24 8x16 Speed Quality Normal Draft or High Quality Paper Autoload Deactivated or Activated Reset buffer Not implemented At paper end 2 Print density Normal 2 Light Very light Dark Very dark Double copy gt General notes The parameters marked with the symbol are the default values The symbol indicates TPL 80 model The symbol indicates TPL 82 5 model Settings remain active even after the printer has been turned off The settings made are stored in EEPROM nonvolative memory During power up if both the LINE FEED and FORM FEED keys are held down the printer enters configuration mode and prints out the setup report it will remain in standby until a key is pressed or characters are received through the communication port see Hexadecimal dump When the LINE FEED key is pressed the printer skips the setup mode and terminates the Hexadecimal dump function When the FORM FEED key is pressed the printer enters the parameter entry mode 1 4 HEXADECIMAL DUMP This function is used to diagnose the characters received through the communication p
6. Name Format Description Notes Default Reference Example 1B 41 n1 n2 Name Format Description Notes Default Reference Example TPL 80 82 5 3 10 3 PRINTER FUNCTIONS with n 3 UD Function Indicates Bar Code size Indicates HRI printing position Not used Not used Not used NIDIA 3 Co These bits correspond to the coding assigned with the GS w and GS H commands Byte2 Indicates Bar Code height Initialize printer ASCII ESC Hex 1B 40 Decimal 27 64 When this command is received the printer resets restoring the default programming and erasing the RAM The machine requires approx seconds from reception of the command to regain its full operating capacity Same as hardware reset Moves stepping motor ASCII ESC A n1 n2 Hex 1B 41 n1 n2 Decimal 27 65 n1 n2 This command moves the paper feeding step motor by a number of steps equal to n1 256 n2 1B 44 n Name Format Range Description Notes Default Reference Example 1B 46 n Name Format Range Description Notes Default Reference Example 1B 47 n Name Format Range Description Notes Default Reference Example 3 PRINTER FUNCTIONS Sets the default paper sensibility ASCII ESC D n Hex 1B 44 n Decimal 27 68 n This command sets the default pa
7. Notes This command cancels the pattern defined for the character code specified by n After the user defined character is cancelled the corresponding pattern for the internal character is printed This command deletes the pattern defined for the specified character code in the font selected by 1B 21 If the user defined character has not been defined for the specified character code the printer ignores this command Default Reference 1B 26 1B 25 Example 1B 40 Name Initialize printer Format ASCII ESC Hex 1B 40 Decimal 27 64 Description Clears the data in the print buffer and resets the printer mode to that in effect when power was turned on Notes The data in the receiver buffer is not cleared The macro definitions are not cleared Default Reference Example 1B 44 n1 nk 00 Name Set horizontal tab positions Format ASCII ESC D n1 nk NUL Hex 1B 44 n1 nk 00 Decimal 27 68 n1 nk 0 Range 1 lt n lt 255 0 lt lt 32 Description Sets horizontal tab positions n specifies the column number for setting a horizontal tab position calculated from the beginning of the line k indicates the total number of horizontal tab positions to be set Notes The horizontal tab position is stored as a value of character width x n measured from the beginning of the line The character width includes the right side character spacing and double width characters are set
8. Reference Example 1B 33 n Name Format Range Description Notes Default Reference Example right side character spacing The printer cannot underline 90 rotated characters and white black inverted characters When underline mode is turned off by setting the value of n to 0 or 48 the data which follows is not underlined Underline mode can also be turned on or off by using 1B 21 Note however that the last received command is the effective one n 0 1B 21 Select 1 8 inch line spacing ASCII ESC 0 Hex 1B 30 Decimal 27 48 Selects 1 8 inch line spacing 1B 32 1B 33 Select 1 6 inch line spacing ASCII ESC 2 Hex 1B 32 Decimal 27 50 Selects 1 6 inch line spacing 1B 30 1B 33 Set line spacing ASCII ESC 3 n Hex 1B 33 n Decimal 27 51 n 0 lt lt 255 Sets line spacing to n x vertical or horizontal motion unit inches The horizontal and vertical motion unit are specified by 1D 50 Changing the horizontal or vertical motion unit does not affect the current line spacing The 1D 50 command can change the horizontal and vertical motion unit However the value cannot be less than the minimum vertical movement amount standard mode the vertical motion unit is used The maximum line spacing is n 255 32 mm n 32 1 6 inch 1B 30 1B 32 1D 50 3 41 TPL 80 82 5 3 PRINTER FUNCTIONS
9. TPL 80 82 5 4 4 CUSTOM 5 1 CHARACTER SETS The printer has six fonts each with 224 characters two font for every emulation 5 CHARACTER SETS ESC POS Emulation PC437 USA Standard Europe FONT 14X24 FONT 10X24 FONT 8X24 0123456789ABCDEF 91234567 9AECDEF 0123456789080 SKB det f 2 WX Ose OPA OS 3 0123456789 lt 7 3 0123456789 3 012346789 207 4 QABCDEFGH JKLMNO 4 4 5 PORSTUVWXYZI 4_ 5 PORSTUWXYZII 5 PORSTUMAYZT AI 6 abodefghiikImno B abcdefghi ik leno 6 abedelghi klanu 7 parstuvwxyz i 7 parsluwxyzii 8 6 e a eii iA alla 9 9 3 A 1 MET iroi s B Sail t E E MU E srzx 4m 4 Fig 5 1 Custom TPT Emulation FONT 16X24 FONT 24X32 FONT 8X16 01234567 89ABCDEF 01 234567 89ABCDEF 1 34887808 DSF AW oo Jtt un 2 R et of 3 cn 3 1 4 BCDEF GH A MX 4 ABCDEFGNIJKimo 0123456789 lt gt 7 s emer 5 PORSTUVWXYZ 1 4 ABCDEFGH JKLMNO 1 we 5 PQRSTUVWXYZ 4_ t munda at A a 6 abcdefghi jkimno eim 9 emery 7 parstuvwxyz A wis ore 8 1 hae TUM dpa 1 9 me 6600 j
10. When the LSB of m 1 after waiting for the period specified by t the LED indicator blinks and the printer waits for the FORM FEED button to be pressed After the button is pressed the printer executes the macro once The printer repeats the operation rtimes Notes This command has an interval of tx 100 msec after a macro is executed by t If this command is received while a macro is being defined the macro definition is aborted and the definition is cleared If the macro is not defined or if ris 0 nothing is executed CUSTOM 3 25 TPL 80 82 5 Default Reference Example 1D 63 Name Format Description Notes Default Reference Example 1D 65 n m I Name Format Range Description TPL 80 82 5 3 26 3 PRINTER FUNCTIONS When the macro is executed by pressing the FORM FEED button m 1 the paper cannot be fed using the FORM FEED button 1D 3A Print counter ASCII GS c Hex 1D 63 Decimal 29 99 Sets the serial counter value in the print buffer and increments or decrements the counter value After setting the current counter value in the print buffer as print data a character string the printer counts up or down based on the count mode set The counter value in the print buffer is printed when the printer receives a print command or the buffer is full The counter print mode is set using 1D 43 30 The counter mode is set using 1D 43 31 or
11. 1B 69 Name Format Description Notes Default Reference Example TPL 80 82 5 3 48 3 PRINTER FUNCTIONS Enable disable front panel buttons ASCII ESC c 5 n Hex 1B 63 35 n Decimal 27 99 53 n 0 lt lt 255 Enables disables the buttons on the front panel When the LSB of nis 0 the panel buttons are enabled When the LSB of nis 1 the panel buttons are disabled Only the LSB of nis effective On the printer the panel buttons are LINE FEED and FORM FEED When the panel buttons are disabled the buttons may only be used after the printer has been reset When the panel buttons are disabled is possible to know the status through the 10 04 command n 0 10 04 Print and feed paper n lines ASCII ESC d n Hex 1B 64 n Decimal 27 100 n 0 lt lt 255 Prints the data in the print buffer and feeds the paper n lines Sets the print starting position at the beginning of the line This command does not affect the line spacing set by 1B 32 or 1B 33 The maximum paper feed amount is 200 lines Even if a paper feed amount of more than 200 lines is set the printer feeds the paper only 200 lines 1B 32 1B 33 Total cut ASCII ESC i Hex 1B 69 Decimal 27 105 This command enables cutter operation If there is no cutter a disabling flag is set and any subsequent cut commands will be ignored The printer waits to complete all paper movement commands before it executes a tota
12. 1D 43 3B In count up mode if the counter value set by this command goes out of the counter operation range set by 1D 43 31 or 1D 43 3B it is forced to revert to the minimum value In count down mode if the counter value set by this command goes out of the counter operation range set by 10 43 31 or 1D 43 3B it is forced to revert to the maximum value 1D 43 30 1D 43 31 1D 43 32 1D 43 3B Ejector commands ASCII GS e n m I Hex 1D 65 n m 1 Decimal 29 101 n m I 0 lt lt 3 5 lt lt 8 This command checks tickets ejector n 0 Ticket produced with defined number of steps see command notes 1 Ejector motor off n 2 Ejector motor on n ticket presenting with 3 x m steps 1 step 36 mm 3 x 12 mm n 5 ticket espulsion n 6 transmits ejector byte status 3 PRINTER FUNCTIONS Notes Default Reference Example 1D 68 n Bit Off On Hex Decimal Function Off 00 0 Not near paper end 01 1 Near paper 1 Off 00 0 Fixed to 0 2 Off 00 0 Paper end sensor On 04 4 Paper is present Off 00 0 Tickets out On 08 8 Ticket present on ejector mouth 4 Off 00 0 Printer stepping motor off On 10 16 Printer stepping motor on Off 00 0 Ejector motor off 20 32 Ejector motor Off 00 0 No error On 40 64 Error occurs 7 Off 00 0 Fixed to 0 n 7 sets maximum ticket length The maximum t
13. 3 PRINTER FUNCTIONS Description Notes Default Reference Example 1B 24 n1 n2 Name Format Description Notes Default Reference Example 1B 25 n1 n2 Name Format Description Notes Default Example This receives an array of data an arranges it in a graphic page at the given coordinates The coordinates define the vertices of a window in which the data is stored x1 y1 2 2 1 1 256 n2 1 y2 n7 256 n8 The values of coordinates x1 and x2 are aligned with the byte Sets bar code printing position ASCII ESC n1 n2 Hex 1B 24 n1 n2 Decimal 27 36 n1 n2 The bar code is printed at position n1 256 n2 If the value exceeds 640 it is rejected Prints grahic page ASCII ESC n1 n2 Hex 1B 25 n1 n2 Decimal 27 37 n1 n2 Prints graphic page starting from the beginning for a number of lines eqaul to n1 256 n2 if the vaule is higher than the lines availables 209 it prints the entire page 1B 2A m nL nH d1 dk Name Format Select bit image mode ASCII ESC m nL nH d1 dk Hex 1B 2A m nL nH d1 dk Decimal 27 42 m nL nH d1 dk 3 5 TPL 80 82 5 3 PRINTER FUNCTIONS Range m 0 1 32 33 0 lt lt 255 0 lt lt 7 0xdx255 Description Selects a bit image mode using m for the number of dots specified by nL and nH as follows m Mode Vertical direction Horizontal direction
14. However the last received setting command is the effective one 1D 21 can also be used to select character height width However the last received setting command is the effective one n 0 1B 2D 1B 45 1B 34 1D 21 Name Format Range Description Notes Default Reference Example 1B 25 Name Format Range Description Notes Default TPL 80 82 5 3 38 Set absolute print position ASCII ESC nL nH Hex 1B 24 nL nH Decimal 27 36 nL nH O lt nL lt 255 lt lt 255 Sets the distance from the beginning of the line to the position at which subsequent characters are to be printed The distance from the beginning of the line to the print position is nL nH x 256 x vertical or horizontal motion unit inches Settings outside the specified printable area are ignored The horizontal and vertical motion unit are specified by 1D 50 1D 50 can change the horizontal and vertical motion unit However the value cannot be less than the minimum horizontal movement amount In standard mode the horizontal motion unit x is used If the setting is outside the printing area width it sets the absolute print position but the left or right margin is set at default value 1B 5C 1D 50 Select cancel user defined characters ASCII ESC n Hex 1B 25 n Decimal 27 37 n 0 lt lt 255 Selects cancels the user defined character set Wh
15. RESERVED 3 49 TPL 80 82 5 Notes Default Reference Example 1B 78 Name Format Range Description Notes Default Reference Example 1B 7B n Name Format Range Description Notes Default Reference Example TPL 80 82 5 3 50 3 PRINTER FUNCTIONS This command is executed immediately even when the data buffer is full Busy 10 04 Select speed quality mode ASCII ESC X n Hex 1B 78 n Decimal 27 120 n 0 lt lt 2 Selects printing speed quality mode n Function 0 Draft mode high speed 1 Normal mode 2 High quality low speed In high quality mode n 2 the printer may be noisy n 1 Turn upside down printing mode on off ASCII ESC n Hex 1B 7B n Decimal 27 123 n 0 lt lt 255 Turns upside down printing mode on or off When the LSB of nis 0 the upside down printing mode is off When the LSB of nis 1 the upside down printing mode is on Only the LSB of nis effective This command is valid only if entered at the beginning of a line In upside down printing mode the printer rotates the line to be printed 180 and then prints it n 0 Upside down printing Off ABCDEFG Upside down printing On Odaqqosv 9SvECLO 0123456 Printing direction 3 PRINTER FUNCTIONS 1B FA n xH xL yH yL Name Format Range Description Notes Default Reference Example
16. n Function 1 Transfers flash bank logo 1 into ram 2 Transfers flash bank logo 2 into ram 3 Transfers flash bank logo 3 into ram 3 51 TPL 80 82 5 Notes Default Reference Example 1B FD nL nH Name Format Range Description Notes Default Reference Example 1B FE n Name Format Range Description Notes Default Reference Example 1D 21n Name Format Range Description TPL 80 82 5 3 PRINTER FUNCTIONS 1B FA 1B FD 1B FE Receive ram bank from serial port ASCII ESC nL nH Hex 1B FD nL nH Decimal 27 253 nL nH 0 lt nL nH lt 255 Receives nL nH x 256 words from the port and puts them into the ram bank The number of data bytes received is nL nH x 256 x 2 Each word is first received as MSByte and then as LSByte If nL nH x 256 is greater than 16384 the data which follows is processed as normal data horizontal dotline is represented to 40 words 91 FA 1B FC 1B FE Transfer ram bank into flash bank ASCII ESC n Hex 1B FE n Decimal 27 254 n 1 lt n lt 3 Transfers the ram bank into the flash bank 32768 bytes n selects the bank as follows n Function 1 Transfers ram bank into flash bank logo 1 2 Transfers ram bank into flash bank logo 2 3 Transfers ram bank into flash bank logo 1B FA 1B FC 1B FD Select character size ASCII GS
17. 1 N dots DPI DPI N of Data k 0 8 dot single density 8 67 100 nL nH x 256 1 8 dot double density 8 67 200 nL nH x 256 32 24 dot single density 24 200 100 nL nH x 256 x 3 33 24 dot double density 24 200 200 nL nH x 256 x 3 Notes The nL and nH indicates the number of bytes If the bit image data input exceeds the number of dots to be printed on a line the excess data is ignored d indicates the bit image data Set a corresponding bit to 1 to print a dot or to 0 to not print the dot If the value of mis outside the specified range nL and data following it are processed as normal data To print the bit image use 0A 0D or 1D 64 After printing a bit image the printer returns to normal data processing mode This command is not affected by the emphasized double strike underline etc print modes except for the upside down mode The relationship between the image data and the dots to be printed is as follows 8 dot bit image 24 dot bit image MSB MSB Bit Bit image image data data LSB LSB Print data Default Reference Example TPL 80 82 5 3 6 CUST M 3 PRINTER FUNCTIONS 1B 2B n1 n2 Name Format Description Notes Default Reference Example 1B 34 n Name Format Range Description Semi graphic printing mode ASCII ESC n1 n2 Hex 1B 2B n1 n2 Decimal 27 43 n1 n2 The bar code is printed at position n1 256 n2 If the
18. 22 characters n 6 CODEBAR max 16 characters n 7 UPC A max 16 characters The rotation command does not affect on bar code printing 1D 68 Request expanded status ASCII GS V Hex 1D 76 Decimal 29 118 This command transmits two bytes each bit indicates the printer status to serial port First byte Bit Off On Hex Decimal Function 0 Off 00 0 Near paper end On 01 1 Paper presence in abundance 1 RESERVED 2 Off 00 0 Paper out On 04 4 Paper presence 3 Off 00 0 Line Feed key released On 08 8 Line Feed key pressed 4 Off 00 0 Form Feed key released On 10 16 Form Feed key pressed 5 Off 00 0 Head temperature correct On 20 32 Head temperature error 6 Off 00 0 Motor off On 40 64 Motor on 7 Off 00 0 No error On 80 128 Error due to paper end Head up etc TPL 80 82 5 3 28 CUSTOM Notes Default Reference Example 1D 77 n Name Format Range Description Notes Default Reference Example 10 E0 n Name Format Range Description 3 PRINTER FUNCTIONS Second byte Bit Off On Hex Decimal Function 0 On 01 1 Printing 1 On 02 2 Head up 2 RESERVED 3 On 08 8 Ticket on the exit mouth 4 RESERVED 5 RESERVED 6 RESERVED 7 RESERVED This command is executed immediately even when the data buffer is full Busy Set bar c
19. 3 1 0A LF Print and line feed 0B VT Vertical tab 0C FF Form feed 0D CR Print and carriage return 18 CAN Cancels line buffer 1B 21 n ESC n Sets print mode 1B 23 n1 n8 ESC Receives data in graphic page 1B 24 n1 n2 ESC 1 2 Sets bar code print position 1B 25 n1 n2 ESC n Prints graphic page 1B 2A m nL nH ESC m nL nH Sets bit image mode 1B 2B n1 n2 ESC n1 n2 Prints in semi graphic mode CUSTOM 3 1 TPL 80 82 5 3 PRINTER FUNCTIONS HEX ASCII Description 1B 34 n ESC Sets resets script mode 1B 3D n ESC n Enables disables form feed key 1B 3F n ESC n Requests printer setting 1B 40 ESC Resets the printer 1B 41 n1 n2 ESC Ant n2 Moves stepping motor 1B 44 n ESC Dn Sets default paper sensitbility 1B 46 n ESC Fn Copies flash bank into ram bank 16Bytes 1B 47 n ESC Gn Sets resets double strike mode 1B 4E n ESC Sets negative mode 1B 50 ESC P Fills ram bank from port 16384 BYTES 1B 52 n ESC Rn Sets font in use 1B 53 ESC Sn Sets paper sensibility in use 1B 55 n ESC Un Sets underline mode 1B 56n ESCVn Sets print mode rotated by 90 1B 57 ESC W Prints a graphic dotline 1B 5A n1 n2 ESC 7 1 n2 Sets form feed steps number 1B 5C nL nH ESC nH Sets relative print position 1B 61 n ESC an Selects justification 1B 63 34 n ESC c4n Selects paper sensor
20. Default Reference Example 1D E3 Name Format Description Notes Default Reference Example TPL 80 82 5 3 30 Reading the number of cuts performed from the printer The command return a string that points out how many cuts are performed by the printer for example if there are performed 2376 cuts it will be 2376 cuts Reading of length cm of printed paper ASCII GS Hex 1D E3 Decimal 29 227 Reading of length cm of printed paper The command return a string pointing out how much paper is printed for example if the printer has print about 2515 5 m it will be 251550cm 3 PRINTER FUNCTIONS 1D E5 Name Reading number of power up Format ASCII GS Hex 1D E5 Decimal 29 229 Description Reading number of power up of the printer Notes The command return a string pointing out the number of turning on of the printer for example if the printer is turned on 512 times it will be 512on Default Reference Example 3 2 2 ESC POS emulation The following table lists all the commands for function management in ESC POS emulation of the printer The commands can be transmitted to the printer at any moment but they will only be carried out when the com mands ahead of them have been executed The commands are carried out when the circular buffer is free to do So The table 3 2 shows the commmands list ordered by their hexadecimal value LEGEND Symbol Funct
21. NICK photocell Alterna tively the paper forward feeds by the number of dotlines preset by the command 1B 5A Notes Default Reference Example CUSTOM 3 3 TPL 80 82 5 3 PRINTER FUNCTIONS 0D Name Carriage return Format ASCII CR Hex 00 Decimal 13 Description When autofeed is CR enabled this command functions in the same way as 0A otherwise it is disregarded Notes The command sets the print position at the beginning of the line Default Reference 0A Example 18 Name Cancel print data buffer Format ASCII CAN Hex 18 Decimal 24 Description Deletes all the print data in the current print buffer Notes The command set the print position to the beginning of the line Default Reference Example 1B 21 n Name Select print modes Format ASCII ESC n Hex 1B 21 n Decimal 27 33 n Description This command sets the print mode Each bit of n is read as follows Bit FUNCTION 0 1 0 1 nu 2 Selects superscript or subscript only for 8x16 Superscript Subscript 3 nu 4 Double height Cancel Set 5 Double width Cancel Set 6 Quadruple height Cancel Set 7 Quadruple width Cancel Set Notes Height and width commands set the mode for a whole line Default n 0 Reference Example 1B 23 n1 n8 Name Receives data in graphic page Format ASCII ESC n1 n8 Hex 1B 23 n1 n8 Decimal 27 35 n1 n8 TPL 80 82 5 3 4 CUSTOM
22. RESERVED On line Off line RESERVED RESERVED RESERVED RESERVED z o 1 1 1 n 2 Off line status Bit Off On Hex Decimal Function 0 RESERVED 1 RESERVED 2 Off 00 0 Cover closed On 04 4 Cover opened 3 Off 00 0 Paper isn t feeded by FEED button On 08 8 Paper is feeded by FEED button 4 RESERVED 5 Off 00 0 Paper presence On 20 32 Printing stop due to paper end 6 Off 00 0 No error On 40 64 Error 7 RESERVED TPL 80 82 5 3 34 CUSTOM 3 PRINTER FUNCTIONS n 3 Error status Bit Off On Hex Decimal Function RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED Off 00 0 No auto recoverable error On 40 64 Auto recoverable error 7 RESERVED 4 Paper roll sensor status Bit Off On Hex Decimal Function 0 RESERVED 1 RESERVED 2 3 Off 00 0 Paper present in abundance On 0C 12 Near paper end 4 RESERVED 5 6 Off 00 0 Paper present On 60 96 Paper not present 7 RESERVED n 20 FULL status 6 bytes 1 Byte 10 DLE 2 byte 0F 3 byte Paper status Bit Off On Hex Decimal Functi
23. bytes To print a dot set the corresponding bit to 1 to not have it print set to O This command can define different user defined character patterns for each font To select the font use 1B 21 The user defined character definitions are cleared when 1B 40 or 1B 3F are executed or the printer is reset or the power shut off Default Internal character set Reference 1B 25 1B 3F Example 1B 2A m nL nH d1 dk Name Select bit image mode Format ASCII ESC i m nL nH d1 dk Hex 1B 2A m nL nH d1 dk Decimal 27 42 m nL nH d1 dk Range m 0 1 32 33 lt lt 255 0 lt lt 2 0 lt 4 lt 255 Description Selects a bit image mode using m for the number of dots specified by nL and nH as follows CUSTOM 3 39 TPL 80 82 5 Notes Default Reference Example 1B 2D n Name Format Range Description Notes TPL 80 82 5 3 40 3 PRINTER FUNCTIONS m Mode Vertical direction Horizontal direction 1 N dots DPI DPI N of Data k 0 8 dot single density 8 67 100 nL nH x 256 1 8 dot double density 8 67 200 nL nH x 256 32 24 dot single density 24 200 100 nL nH x 256 x 3 33 24 dot double density 24 200 200 nL nH x 256 x 3 The nL and nH commands indicate the number of dots of the bit image in the horizontal direction The number of dots is calculated using nL nH x 256 If the bit image data input exceeds
24. of power up ASCII GS Hex 1D E5 Decimal 29 229 Reading number of power up of the printer The command return a string pointing out the number of turning on of the printer for example if the printer is turned on 512 times it will be 512on 3 67 TPL 80 82 5 3 PRINTER FUNCTIONS Blank Page TPL 80 82 5 3 68 CUST M 4 TECHNICAL SPECIFICATIONS 4 1 TECHNICAL SPECIFICATIONS Table 4 1 gives the main technical specifications for the printer models Tab 4 1 TPL 80 TPL 82 5 203 DPI 8 dot mm Paper end head open near paper end Paper anti jamming head temperature A o 5 Thermal fixed head 8 dot mm Straight 90 180 360 Custom TPT emulation 6 logos 608 x 215 each ESC POS emulation 3 logos 608 x 431 each 110 mm sec 130 mm sec 24Vdc Type of paper Recommended types of paper Paper thickness Paper roll size Core thickness Core type Printing method Printing mode Printing format Characters font Flash memory Graphic memory U em 3 5 n gt Note The recommended minimum basis weight is 58 g m 2 Printer weight is given without paper roll CUSTOM 4 1 TPL 80 82 5 4 TECHNICAL SPECIFICATIONS Environmental conditions Operating temperature 0 C 50 C Relative humidity 10 80 w o condensation Storage temperature humidity 20 C 70 C 10 90 ESC POS EMULATION Number of columns Characters L x H
25. or bL bH specify the counter range nindicates the stepping amount when counting up or down rindicates the repetition number when the counter value is fixed Count up mode is specified when aL aH x 256 lt bL bH x 256 and n 0 and rzO Count down mode is specified when aL aH x 256 gt bL bH x 256 and n zO and rzO Counting stops when aL aH x 256 bL x 256 orn or r 0 Setting the count up mode the minimum counter value is aL aH x 256 and the maximum value is bL bH x 256 If the counting up reaches a value that exceeds the maximum it resets to the minimum value Setting the count down mode the maximum counter value is aL aH x 256 and the minimum value is bL 65 x 256 If the counting down reaches a value less than the minimum it resets to the maximum value When this command is executed the internal count that indicates the repetition number specified by ris cleared aL 1 aH 0 bL 255 bH 255 n 1 r 1 1D 43 30 1D 43 32 1D 43 3B 1D 63 Set counter ASCII GS C 2 nL nH Hex 1D 43 32 nL nH Decimal 29 67 50 nL nH 0 lt nL nH lt 255 Sets the serial number counter value nL and nH determine the value of the serial number counter set by nL nH x 256 In count up mode if the counter value specified by this command goes out of the counter operation range specified by 1D 43 31 or 1D 43 3B it is forced to conve
26. the number of dots to be printed on a line the excess data is ignored d indicates the bit image data Set a corresponding bit to 1 to print a dot or to O to not print the dot Ifthe value of mis outside the specified range nL and data following it are processed as normal data e If the width of the printing area set by 10 4C and 10 57 is less than the width required by the data set using 1B 2A the excess data are ignored To print the bit image use 0A 0D 1B 4A or 1B 64 After printing a bit image the printer returns to normal data processing mode This command is not affected by the emphasized double strike underline etc print modes except for the upside down mode The relationship between the image data and the dots to be printed is as follows 8 dot bit image 24 dot bit image Print data Print data Turn underline mode on off ASCII ESC Hex 1B 2D n Decimal 27 45 0 lt lt 2 48 lt lt 50 Turns underline mode or off based on the following values of n n 0 48 Turns off underline mode 1 49 Turns underline mode 1 dot thick n 2 50 Turns on underline mode 2 dot thick The printer can underline all characters but cannot underline the space set by 09 and 3 PRINTER FUNCTIONS Default Reference Example 1B 30 Name Format Description Notes Default Reference Example 1B 32 Name Format Description Notes Default
27. to stop printing 1B 63 35 n ESC c5n Enables disables panel buttons 1B 64 n ESC dn Prints and feed paper n lines 1B 66 n ESC fn Sets default font 1B 69 ESC i Cuts paper completely 1B 6D ESC m Cuts paper partially 1B 72 ESC Copies RAM bank into flash bank 16kbytes 1B 73 ESC s Sends RAM bank to port 16kbytes Ci 1B 76 ESC v Transmit printer status a 1B 7A ESCz Sets vertical tab value 1B 7B n ESC n Sets cancels upside down character printing 1B 7C ESC Cancels graphic page 1B FA n xL xH yH yL ESC n xL xH yH yL Prints graphic bank 1B FB nL nH ESC nL nH Transmits RAM bank to serial port C 1B FC n ESC n Transfers flash bank into RAM bank 1B FD nL nH ESC nL nH Receives RAM bank from serial port 1B FE n ESC n Transfers RAM bank into flash bank 1D 3A GS Sets start end of macro definition 1D 43 30 nm GSCOnm Selects counter print mode 1D 43 31 aL aH bL bHnr GS C 1 aL aH bLbHn r Selects counter mode A 1D 43 32 nL nH GS C 2 nL nH Sets counter 1D 43 3B sa 3B sb 3B sn 3B sr 3B sc 3B GS sa sb sn Sr SC Selects counter mode B 1D 48 n GS Hn Selects HRI print position 1D 49 n GS In Transmit printer ID 1D 5Ertm GS rtm Executes macro 1D 63 GS c Print counter 1D 65 n m GS e n m I Ejector commands 1D 68 n GS hn Selects bar code height 10 6B n HRICR GS lt gt
28. used The horizontal direction is perpendicular to the paper feed direction standard mode the following commands use x or y regardless of character rotation upside down or 90 clockwise rotation Commands using x 1B 24 1B 5C 1D 4C 1D 57 Commands using y 1B 33 1B 4A This command does not affect the previously specified values The calculated result from combining this command with others is truncated to the minimum value of the mechanical pitch or an exact multiple of that value x 200 y 200 1B 24 1B 5C 1B 33 1B 4A 1D 4C 1D 57 Set printing area width ASCII GS nL nH Hex 1D 57 nL nH Decimal 29 87 nL nH OxnL nH lt 255 0 lt nH x 256 lt 832 Sets the printing area width to the area specified by nL and nH The printing area width is set to nL nH x 256 x horizontal motion unit inches Printable area I He TC Left margin Printing area width This command is only enabled if set at the beginning of the line 3 PRINTER FUNCTIONS If the right margin is greater than the printable area the printing area width is set at maximum value If the printing area width 0 it is set at the maximum value The horizontal and vertical motion units are specified by 1D 50 Changing the horizontal or vertical motion unit does not affect the current left margin The 1D 50 command can change the horizontal and vertical motion unit H
29. 0 75 n 3 1D 6B Set printing density ASCII GS n Hex 1D 7C n Decimal 29 124 n 0 lt lt 4 48 lt lt 52 Sets printing density n specifies printing density as follows 3 65 TPL 80 82 5 3 PRINTER FUNCTIONS n Printing density 0 48 Very light 1 49 Light 2 50 Normal 3 51 Dark 4 52 Very dark Notes Printing density reverts to the default value when the printer is reset or turned off Default n 2 Reference Example 1D 7E n Name Set superscript subscript Format ASCII GS 0 n Hex 1D Decimal 29 126 n Range n 0 1 48 49 Description Sets superscript or subscript character position n specifies the position as follows n Function 0 48 Subscript character position 1 49 Superscript character position Notes This command is executed if there are characters of different height on the same line Default n 0 Reference 1B 21 1D 21 Example 1D E0 n Name Enable disable automatic FULL STATUS back Format ASCII GS n Hex 1D EO n Decimal 29 224 n Range 0 lt lt 255 Description Enable disable automatic full status back n specifies the composition of FULL STATUS as follows Bit Off On Hex Decimal Function 0 Off 00 0 Disable Paper status On 01 1 Enable Paper status 1 Off 00 0 Disable User status On 02 2 Enable User status 2 Off 00 0 Disable Recoverable Er
30. 2 CGOMANDS DESCRIPTION aeo oe Fen neo ne dae ao eek aes 3 1 3 2 1 Custom TPT emulation 1 00000 3 1 3 2 2 ESC POS 3 31 4 TECHNICAL SPECIFICATIONS 4 1 TECHNICAL SPECIFICATIONS 2 4 1 4 2 DIMENSIONS EE 4 3 5 CHARACTER SETS SETS uc 5 1 APPENDIX A ACCESSORIES AND SPARE PARTS AJ AGCGESSORIES ERREUR RAIN EE I A 1 huMMEZeUSEBgE es A 1 A2 SUPPLIES ce A 2 INTRODUCTION MANUAL CONTENTS In addition to the Introduction which includes a description of the explanatory notes used in the manual general safety information how to unpack the printer and a brief description of the printer including its basic features this manual is organized as follows Chapter 1 Contains the information required for correct printer installation and its proper use Chapter 2 Contains information on interface specifications Chapter 3 Contains a description of the printer command set Chapter 4 Contains Technical Specifications of the printer Chapter 5 Contains the character sets fonts used by the printer EXPLANATORY NOTES USED IN THIS MANUAL Gives important information or s
31. 48 n m Range 0 lt lt 5 m 0 1 2 48 49 50 Description Selects a print mode for the serial number counter n specifies the number of digits to be printed as follows when n 0 the printer prints the actual digits indicated by the numeric value when n 1 to 5 the command sets the number of digits to be printed m specifies the printing position within the entire range of printed digits as follows m Printing position Processing of digits less than those specified 0 48 Flush right Adds spaces to the left 1 49 Flush right Adds 0 to the left 2 50 Flush left Adds spaces to the right Notes Default Reference Example O indicates a space If normis out of the defined range the previously set print mode is not changed If n 0 mis not applicable 10 43 31 aL aH Name Format Range Description TPL 80 82 5 n 0 m 0 1D 43 31 1D 43 32 1D 43 3B 1D 63 n 3 m 0 n 3 m 1 n 3 m 2 001 001 100 Select count mode A ASCII GS C 1 aL aH bL bH n r Hex 1D 43 31 aL aH bL bH n r Decimal 29 67 49 aL aH bL bH n r O lt aL aH lt 255 0 lt bL bH lt 255 0 lt lt 255 Selects a count mode for the serial number counter 3 22 CUSTOM 3 PRINTER FUNCTIONS Notes Default Reference Example GS C 2 nL nH Name Format Range Description Notes Default Reference Example aL aH or bL bH specify the c
32. 9 mm below tihs value the ticket espulsion could have some problems 1D 6B Select font for HRI characters ASCII GS f n Hex 1D 66 n Decimal 29 102 n n 0 1 48 49 Selects a font for the HRI characters used when printing a bar code n selects a font from the following table n Font 0 48 FontA 14x24 1 49 Font B 10x24 HRI characters are printed at the position specified by 1D 48 n 0 1D 48 1D 6B Set bar code height ASCII GS h n Hex 1D 68 n Decimal 29 104 1 lt n lt 255 Sets the height of the bar code n specifies the number of vertical dots n 96 12mm 1D 6B 10 6B m d1 dk NUL 10 6B m n d1 dn Name Format Print bar code ASCII GS k m NUL Hex 1D 6B m 00 Decimal 29 107 m 0 3 61 TPL 80 82 5 3 PRINTER FUNCTIONS ASCII GS m n Hex 1D 6B m n Decimal 29 107 m n Range 0 lt lt 6 65 lt m lt 73 Description Selects a bar code system and prints the bar code m selects a bar code system as follows m Bar code system No of characters Remarks 0 UPC A 11 lt k lt 12 48 lt lt 57 1 11 lt lt 12 48 lt d lt 57 2 1 JAN 12 lt lt 13 48 lt lt 57 3 EANB JAN 7 lt k lt 8 48 lt d lt 57 48 lt d lt 57 65 lt d lt 90 32 4 CODESS 36 37 43 45 46 47 5 ITF 1 lt
33. CU EXP f D ai OURN 9 emin E e P 905e9c t cesses Widin 15124 Fig 5 2 CUSTOM 5 1 TPL 80 82 5 5 CHARACTER SETS Blank page APPENDIX A ACCESSORIES AND SPARE PARTS A 1 ACCESSORIES A 1 1 Power supply The figure below illustrates the power supply provided by Custom to be utilized for operating printers RANGE TOLERANCE B lt 8 0 1 8 25 0 15 25 80 0 25 80 250 0 4 250 800 0 8 800 2600 ERE ANGULAR 0 3 Note Dimensioni mm Output specifications 20 85 Rh w o condensation 10 C 75 C 10 95 w o condensation Protection devices Shortcircuit overload CUSTOM 1 TPL 80 82 5 APPENDIX A ACCESSORIES AND SPARE PARTS A 2 SPARE PARTS Paper roll Tab A 2 RCT80X48 25MM Thermal paper roll 80 mm RCT82 5X48 25MM Thermal paper roll 82 5 mm
34. D 4 30 n m Decimal 29 67 48 n m Range 0 lt lt 5 m 0 1 2 48 49 50 Description Selects a print mode for the serial number counter n specifies the number of digits to be printed as follows when n 0 the printer prints the actual digits indicated by the numeric value when n 1 to 5 the command sets the number of digits to be printed m specifies the printing position within the entire range of printed digits as follows m Printing position Processing of digits less than those specified 0 48 Align right Adds spaces to the left 1 49 Align right Adds a 0 to the left 2 50 Align left Adds spaces to the right Notes If normis out of the defined range the previously set print mode is not changed Ifn 0 mis not applicable Default n 0 m 0 Reference 1D 43 31 1D 43 32 1D 43 3B 1D 63 Example n 3 m 0 n 3 m 1 n 3 2 001 001 100 indicates a space 10 43 31 aL aH bL nr Name Select count mode A Format ASCII GS C 1 aL aH bL bH n r Hex 1D 43 31 aL aH bL bH n r Decimal 29 67 49 aL aH bL bH n r Range 0 lt aH lt 255 0 bL bH lt 255 O lt n r lt 255 TPL 80 82 5 3 54 CUSTOM 3 PRINTER FUNCTIONS Description Notes Default Reference Example 1D 43 32 nL nH Name Format Range Description Notes Default Reference Example Selects a count mode for the serial number counter aL aH
35. H xL yH yL Name Format Range Description Print graphic bank 608 x 215 dots ASCII ESC nxH xL Hex 1B FA n xH xL yL Decimal 27 250 n xH xL yH yL 0xns6 0 xH xL yL x 255 Prints graphic bank from flash or ram n selects the graphic source as follows 3 19 TPL 80 82 5 Notes Default Reference Example 1B FB Name Format Description Notes Default Reference Example 1B FC n Name Format Range Description Notes 3 PRINTER FUNCTIONS Function Print ram bank Print flash bank logo 1 Print flash bank logo 2 Print flash bank logo 3 Print flash bank logo 4 Print flash bank logo 5 a gt wo N a Print flash bank logo 6 xL XHx 256 specifies the starting dotline 1 215 yL yH x 256 specifies the number of lines to print If xL xH x 256 gt 215the printer does not execute the command If xL XH x 256 yL x 256 gt 215 the printer prints only 215 xL xH x 256 1 dotline 1B FC 1B FD 1B 4FE To print from ram bank dotline 100 to dotline 299 send 1B FA 00 00 64 00 C7 Transmit ram bank to serial port ASCII ESC nL nH Hex 1B FB nL nH Decimal 27 251 nL nH Transmits nH x 256 nL bytes of ram bank to serial port The size of ram bank for graphic printing is 640 horizontal dots 80 bytes dotline x 409 vertic
36. SC n Hex 1B FE n Decimal 27 254 n 1 lt n lt 6 Transfers the ram bank into the flash bank 32768 bytes n selects the bank as follows n Function 1 Transfers ram bank into flash bank logo 1 Transfers ram bank into flash bank logo 2 Transfers ram bank into flash bank logo 3 Transfers ram bank into flash bank logo 4 Transfers ram bank into flash bank logo 5 IAJ AJOJN Transfers ram bank into flash bank logo 6 1B FA 1B FC 1B FD Start end macro definition ASCII GS Hex 1D 3A Decimal 29 58 Starts or ends macro definition 3 21 TPL 80 82 5 3 PRINTER FUNCTIONS Notes Default Reference Example 1D 43 30 nm Macro definition starts when this command is received during normal operation When 1D 5E is received during macro definition the printer ends macro definition and clears all definitions Macros are not defined when power is turned on to the machine Macro content is not cancelled by the 1B 40 command Therefore 1B 40 may be included in the content of macro definitions If the printer receives 1D 3A a second time after previously receiving 1D 3A the printer remains in macro undefined status The contents of the macro can be defined up to 2048 bytes If the macro definition exceeds 2048 bytes excess data is not stored 1D 5E Name Select counter print mode Format ASCII GS C 0 n m Hex 1D 43 30 n m Decimal 29 67
37. SCII GS c Hex 1D 63 Decimal 29 99 Description Sets the serial counter value in the print buffer and increments or decrements the counter value Notes After setting the current counter value in the print buffer as print data a character string the printer counts up or down based on the count mode set The counter value in 3 59 TPL 80 82 5 3 PRINTER FUNCTIONS the print buffer is printed when the printer receives a print command or the buffer is full The counter print mode is set using 1D 43 30 The counter mode is set using 1D 43 31 or 1D 43 3B In count up mode if the counter value set by this command goes out of the counter operation range set by 1D 43 31 or 1D 43 3B it is forced to revert to the minimum value In count down mode if the counter value set by this command goes out of the counter operation range set by 1D 43 31 or 1D 43 3B it is forced to revert to the maximum value Default Reference 1D 43 30 1D 43 31 1D 43 32 1D 43 3B Example 1D 65 n m I Name Ejector commands Format ASCII GS e n m I Hex 1D 65 n m 1 Decimal 29 101 n m I Range 0 lt lt 3 5 lt lt 8 Description This command checks tickets ejector n 0 Ticket produced with defined number of steps see command notes 1 Ejector motor off n 2 Ejector motor on n ticket presenting with 3 x m steps 1 step 36 mm 3 x 12 mm n 5 ticket espulsion n 6 transmits e
38. TIONS d i EA 4 JL 2 AUDIT Denm Fig 1 1 1 1 1 Power supply For the power supply every model of the printer is equipped with a male 90 mobile screw pitch 5 08mm terminal J5 The signals on the power suppy connector pins are as follows WARNING Respect power supply polarity Pin no Signal Tab 1 1 1 GND 2 24Vcc power supply 1 2 SELF TEST Printer operating status is indicated in the configuration print out in which next to the name of the components displayed see fig 1 2 and fig 1 3 the following information is given e under INTERFACE is given the interface present RS232 CENTRONICS USB under EEPROM TEST and CUTTER TEST the message OK appears if functioning and NOT OK if faulty under EJECTER TEST the message OK appears if functioning NONE if not present and NOT OK if faulty under HEAD TEMPERATURE is given the temperature of the head e under PAPER PRINTED is given the number of centimeters of paper printed TPL 80 82 5 1 INSTALLATION AND USE under CUT COUNTER is given the number of cuts made under POWER ON COUNTER is given the number of power ups made 5 NOTE f the printer has a USB interface and the cable is plugged into the printer connector the message USB will appear next to the address assigned by the Host to the USB peripheral de
39. Thermal printer for information kiosks and ATMs TPL 80 82 5 mm User Manual CUSTZM www custom it TPL 80 82 5 All rights reserved Total or partial reproduction of this manual in whatever form whether by printed or electronic means is forbidden While guaranteeing that the information contained in it has been carefully checked CUSTOM ENGINEERING SPA and other entities utilized in the realization of this manual bear no responsibility for how the manual is used Information regarding any errors found in it or suggestions on how it could be improved are appreciated Since products are subject to continuous check and improvement CUSTOM ENGINEERING SPA reserves the right to make changes in information contained in this manual without prior notification COD DOME TPL82 5 REV 1 01 Copyright 2005 CUSTOM ENGINEERING SPA Italy CUSTOM ENGINEERING SPA Str Berettine 2 43010 Fontevivo PARMA Italy Tel 39 0521 680111 Fax 39 0521 610701 http www custom it Customer Service Department OEM AREA Tel 39 059 88 69 587 Email support custom it PRINTER COMPONENTS A TPL825 S Front external view 1 Printer frame 2 Paper roll support Near paper end sensor Paper roll Printing mechanism Cutter 7 Paper outfeed B Rear external view with RS232 serial interface 1 Power supply connector 2 RS232 serial connector 3 Near paper end led 4 Status led 5 Power on led 6 Form Feed K
40. al dots 32720 bytes 16360 words 1B FC 1B FD 1B FE Transfer flash bank into ram bank ASCII ESC n Hex 1B FC n Decimal 27 252 n 1 lt n lt 6 Transfers flash bank into ram bank 32768 bytes n selects the bank as follows n Function Transfers flash bank logo 1 into ram Transfers flash bank logo 2 into ram Transfers flash bank logo 3 into ram Transfers flash bank logo 4 into ram Transfers flash bank logo 5 into ram OJJ AJOJN Transfers flash bank ogo 6 into ram TPL 80 82 5 3 20 Default Reference Example 1B FD nL nH Name Format Range Description Notes Default Reference Example 1B FE n Name Format Range Description Notes Default Reference Example 1D 3A Name Format Description 3 PRINTER FUNCTIONS 1B FA 1B FD 1B FE Receive ram bank from serial port ASCII ESC nL nH Hex 1B FD nL nH Decimal 27 253 nL nH 0 lt nL nH x 255 Receives nL nH x 256 words from the port and puts them into the ram bank The number of data bytes received is nL nH x 256 x 2 Each word is first received as MSByte and then as LSByte If nL nH x 256 is greater than 16384 the data which follows is processed as normal data horizontal dotline is represented to 40 words 1B FA 1B FC 1B FE Transfer ram bank into flash bank ASCII E
41. and off the emphasized mode However the last received command is the effective one n 0 1B 21 Turn double strike mode on off ASCII ESC G n Hex 1B 47 n Decimal 27 71 n 0 lt lt 255 Turns double strike mode on or off When the LSB of nis 0 the double strike mode is off When the LSB of nis 1 the double strike mode is on e Only the LSB of n is effective Printer output is the same in double strike and emphasized mode n 0 1B 45 Print and paper feed ASCII ESC J n Hex 1B 4A n Decimal 27 74 n 0 lt lt 255 Prints the data in the print buffer and feeds the paper n x vertical or horizontal motion 3 PRINTER FUNCTIONS unit inches Notes After printing has been completed this command sets the print starting position to the beginning of the line The paper feed amount set by this command does not affect the values set by 1B 32 or 1B 33 The horizontal and vertical motion units are specified by 1D 50 1D 50 can change the vertical and horizontal motion unit However the value cannot be less than the minimum vertical movement amount In standard mode the vertical motion unit is used The maximum paper feed amount is 31 8 mm Default Reference 1D 50 Example 1B 52 Name Select an international character set Format ASCII ESC R n Hex 1B 52 n Decimal 27 82 n Range 0 lt lt 12 Description Selects the international character set n according to the
42. ange Description Notes Default Reference Example TPL 80 82 5 3 46 Set relative print position ASCII ESC nL nH Hex 1B 5C nL nH Decimal 27 92 nL nH O0 lt nL lt 255 0 lt nH lt 255 Sets the print starting position based on the current position by using the horizontal or vertical motion unit This command sets the distance from the current position to nL nH x 256 x horizontal or vertical motion unit Any setting that exceeds the printable area is ignored When the starting position is specified by n motion units to the right nL nH x 256 When the starting position is specified by n motion units to the left negative direction use the complement of 65536 nL nH x 256 65536 n If setting exceeds the printing area width the left or right margin is set to the default value The horizontal and vertical motion unit are specified by 1D 50 1D 50 can change the horizontal and vertical motion units However the value cannot be less than the minimum horizontal movement amount standard mode the horizontal motion unit is used 1B 24 1D 50 3 PRINTER FUNCTIONS 1B 61 n Name Select justification Format ASCII ESC a n Hex 1B 61 n Decimal 27 97 n Range 0 lt lt 2 48 lt lt 50 Description Aligns all data in one line to the specified position n selects the type of justification as follows n Justifi
43. ank into flash bank 16Kbytes ASCII ESC r n Hex 1B 72 n Decimal 27 114 n 1 lt n lt 6 The value of n selects the flash bank n 1 1 bank n 2 2 bank n 3 3 bank n 4 4 bank n 5 5 bank n 6 6 bank If n 0 or n gt 6 the command is ignored For about 1 sec the printer does not receive characters or commands The serial version return 77 if flash memory is not programmed 88 if flash memory is not erased AA if flash memory is programmed 3 17 TPL 80 82 5 3 PRINTER FUNCTIONS Example 1B 73 Name Format Description Notes Default Reference Example 1B 76 Name Format Description Notes Default Reference Example 1B 7A Name Format Description TPL 80 82 5 3 18 Sends ram bank to port 16Kbytes ASCII ESC s Hex 1B 73 Decimal 27 115 This commands sends 16384 RAM bytes to serial port Transmit status request ASCII ESC V Hex 1B 76 Decimal 27 118 This command transmits a byte where each bit indicates the printer status to serial port Bit Off On Hex Decimal Function 0 Off 00 0 Near paper end On 01 1 Paper presence in abundance 1 RESERVED 2 Off 00 0 Paper out On 04 4 Paper presence 3 Off 00 0 Line Feed key released On 08 8 Line Feed key pressed 4 Off 00 0 Form Feed key released On 10 16 Form Feed key pressed 5 Off 00 0 Head temperature correct On 20 32 Hea
44. bit 3 13 TPL 80 82 5 3 PRINTER FUNCTIONS 1B 57 80 bytes Name Prints a graphic dotline Format ASCII ESC W 76bytes 80 bytes Hex 1B 57 76bytes 80 bytes Decimal 27 87 80 bytes Description This command prints a dotline 608 8640 dots after amp 76 80 bytes and feeds the paper Notes indicates TPL 80 Oindicates TPL 82 5 Default Reference Example 1B 5A n1 n2 Name Sets the number of steps for form feed Format ASCII ESC Z n1 n2 Hex 1B 5A n1 n2 Decimale 27 90 n1 n2 Description When the printer receives an FF 0C character or when the FF key is pressed the paper forward feeds until the photocell finds a reference point or up to the distance preset in the Eeprom The default value which is 240 30 mm can be modified by the user The number of steps is given by n1 256 n2 The set value is stored in the Eeprom and continues to be stored even when the printer is switched off Notes Default Reference Example 1B 5C nL nH Name Set relative print position Format ASCII ESC nL nH Hex 1B 5C nL nH Decimal 27 92 nL nH Range 0xnL lt 255 0 lt lt 255 Description Sets the print starting position based on the current position by using the horizontal or vertical motion unit This command sets the distance from the current position to nL nH x 256 x horizontal or vertical motion unit Notes Any setting that exceeds the printable area
45. cation 0 48 Flush left 1 49 Centered 2 50 Flush right Notes This command is only enabled when inserted at the beginning of a line Lines are justified within the specified printing area Spaces set by 09 1B 24 and 1B 5C will be justified according to the previously entered mode Default n 0 Reference Example Flush left Centered Flush right ABC ABC ABC ABCD ABCD ABCD ABCDE ABCDE ABCDE 1B 63 34 n Name Select paper sensor to stop printing Format ASCII ESC C 4 n Hex 1B 63 34 n Decimale 27 99 52 n Range lt lt 255 Description Selects the paper sensor used to stop printing when a near paper end is deleted using n as follows Bit Off On Hex Decimal Function 0 Off 00 0 Paper roll end sensor enabled On 01 1 Paper roll near end sensor enabled 1 RESERVED 2 RESERVED 3 RESERVED 4 RESERVED 5 RESERVED 6 RESERVED 7 RESERVED Notes When a near paper end is detected printing stops after printing the current line and feeding the paper The paper roll near end sensor is enabled when either bit 0 is 1 This setting is not cleared by printer resetting because it is stored in the Eeprom Default n 0 Reference CUSTOM 3 47 TPL 80 82 5 Example 1B 63 35 n Name Format Range Description Notes Default Reference Example ESC dn Name Format Range Description Notes Default Reference Example
46. cimal 27 52 n 0 lt lt 1 48 lt lt 49 Turns italic mode on off based on the following values of n n Function 0 48 Turns off italic mode 1 49 Turns on italic mode 3 7 TPL 80 82 5 3 PRINTER FUNCTIONS Notes The printer can print any character in italic mode When italic mode is turned off by setting the value of n to 0 or 48 the data which follows is printed in normal mode talic mode can also be turned on or off using 1B 21 Note however that the last received command is the effective one Default n 0 Reference 1B 21 Example 1B 3D n Name Enables Disables Form Feed key Format ASCII ESC n Hex 1B 3D n Decimal 27 61 n Description This command is used to control the Form Feed key Normally when this key is pressed the paper forward feeds until a reference mark is detected or until the steps set by the 1B 5A command have been completed When the key is released a character FF 0C is transmitted In this way a controller can check the output of receipts with progressive number etc directly n 0 Disables transmission Enables the Form Feed key n gt 0 Enables transmission when the Form Feed key is pressed Notes Default Reference Example 1B 3F n Name Printer setting request Format ASCII ESC Hex 1B 3F n Decimal 27 63 Range 32 lt lt 126 Description This command transmits two bytes to serial port when each bit indicates the
47. combining two characters and one character ASCII character is defined by transmitting twice consecutively Specific character Data transmission ASCII Hex Decimal SHIFT S 7B 53 123 83 CODE A A 7B 41 123 65 CODE B B 7B 42 123 66 CODE C C 7B 43 123 67 FNC1 1 7B 31 123 49 FNC2 2 7B 32 123 50 FNC3 3 7B 33 123 51 FNC4 4 7B 34 123 52 7 7 123 123 Default Reference 1D 48 1D 66 1D 68 Example 3 63 TPL 80 82 5 3 PRINTER FUNCTIONS 10 72 Name Transmit status Format ASCII GS r n Hex 1D 72 n Decimal 29 114 n Range n 1 49 Description Transmits the status specified by n as follows n Function 1 49 Transmits paper sensor status same as 1B 76 Paper sensor status n 1 49 Bit Off On Hex Decimal Function 0 RESERVED 1 RESERVED 2 3 Off 00 0 Paper end sensor paper present On 0 12 Paper end sensor paper not present 4 Off 00 0 Not used Fixed to Off 5 RESERVED 6 RESERVED 7 RESERVED Notes This command is executed when the data is processed in the data buffer Therefore there may be a time lag between receiving the command and transmitting the status depending on data buffer status Default Reference 10 04 1B 76 Example 1D 76 Name Request expanded status Format ASCII GS V Hex 1D 76 Decima
48. cutes macro 1D 63 GSc Print counter 10 66 n GS fn Selects font for HRI characters 10 68 n GS hn Selects bar code height 1D 6B n lt HRI gt CR GS k n lt HRI gt CR Prints a bar code 1D 72 GSrn Transmit status 1D 76 GS v Request extended status 1D 77 n GS wn Selects horizontal dimension enlargement of bar code 1D 7E n GS n Set superscript subscript 1D 7C n GS 1n Sets print density 1D EO n GS n Enable disable automatic FULL STATUS back 1D E2 GS Reading number of cuts performed from the printer 1D E3 GS Reading of length cm of printed paper 1D E5 GS Reading number of power up TPL 80 82 5 3 32 CUSTOM 3 PRINTER FUNCTIONS In the table listed above the command marked with this symbol defined only for the serial interface Given below are more detailed descriptions of each command 08 Name Back space Format ASCII BS Hex 08 Decimal 8 Description Moves print position to previous character Notes Can be used to put two characters at the same position Default Reference Example 09 Name Horizontal tab Format ASCII HT Hex 09 Decimal 9 Description Moves the print position to the next horizontal tab position Notes Ignored unless the next horizontal tab position has been set If the command is received when the printing position is at the right margin the printer executes print buffer full printing and horizontal tab processing from the beginning o
49. d temperature error 6 Off 00 0 Motor off On 40 64 Motor on 7 Off 00 0 No error On 80 128 Error due to paper end Head up etc This command is executed immediately even when the data buffer is full Busy Sets the vertical tab value ASCII ESC 2 1B Decimal 27 122 Sets the number of feeds lines when a vertical tab character is received The default value on switching on the printer is 10 The set value is valid until the printer is next initialized Notes Default Reference Example 1B 7B n Name Format Range Description Notes Default Reference Example 1B 7C Name Format Description Notes Default Reference Example 3 PRINTER FUNCTIONS Turn upside down printing mode on off ASCII ESC n Hex 1B 7B n Decimal 27 123 n 0 lt lt 255 Turns upside down printing mode on or off When the LSB of nis 0 the upside down printing mode is off When the LSB of nis 1 the upside down printing mode is on e Only the LSB of n is effective This command is valid only if entered at the beginning of a line In upside down printing mode the printer rotates the line to be printed 180 and then prints it n 0 Upside down printing Off ABCDEFG Upside down printing On 9SVECLO Odaqqogsv 0123456 Printing direction Delete graphic page ASCII ESC Hex 1B 7C Decimale 27 124 This command deletes graphic page 1B FA n x
50. dards and have the following specifications Communication speed 12 Mbit sec Receptacle series B type connector Refer to the table 2 3 for the connector pin signals and connection to a device PIN SIGNAL DESCRIPTION Tab 2 3 1 VBUS N C 2 D Data 3 D Data 4 GND Ground signal Shell Shield Cable shield TPL 80 82 5 2 4 CUSTZM 3 PRINTER FUNCTIONS 3 1 PRINT DIRECTION The printer has two printing directions which can be selected by means of the control characters normal and Eb bd ee TPL 82 5 J9jund Ticket printer 681141 m A T m m A m Z Fig 3 1 3 2 COMMANDS DESCRIPTION 3 2 1 Custom TPT Emulation The following table lists all the commands for function management in Custom TPT Emulation of the printer The commands can be transmitted to the printer at any moment but they will only be carried out when the commands ahead of them have been executed The commands are carried out when the circular buffer is free to do so The table 3 1 shows the commmands list ordered by their hexadecimal value LEGEND Symbol Function indicates the representation of the command hexadecimal value for example 40 means HEX 40 ASCII character not performable are optional parameters that can have different values COMMAND DESCRIPTION TABLE Tab
51. e 1B 21n Name Select print modes Format ASCII ESC n Hex 1B 21 n Decimal 27 33 n Range 0 lt lt 255 Description Selects print modes using n see table below Bit Off On Hex Decimal Function 0 Off 00 0 Character font A selected On 01 1 Character font B selected 1 RESERVED 2 RESERVED 3 Off 00 0 Expanded mode not selected On 08 8 Expanded mode selected 4 Off 00 0 Double height mode not selected On 10 16 Double height mode selected 5 Off 00 0 Double width mode not selected On 20 32 Double width mode selected 6 Off 00 0 Italic mode not selected On 40 64 Italic mode selected 7 Off 00 0 Underline mode not selected On 80 128 Underline mode selected Notes The printer can underline all characters but cannot underline the spaces set by 09 TPL 80 82 5 3 PRINTER FUNCTIONS Default Reference Example 1B 24 nL nH 1B 24 1B 5C and 90 rotated characters When characters are enlarged to different heights on one line the characters are aligned at the baseline or topline see 1D 7E This command resets the left and right margin at default value see 1D 4C 1D 57 1B 45 can also be used to turn the emphasized mode on off However the last received setting command is the effective one 1B 2D can also be used to turn the underlining mode on off However the last received setting command is the effective one 1B 34 can also be used to turn the italic mode on off
52. en the Least Significant Bit LSB of n is 0 the user defined character set is canceled When the LSB of n is 1 the user defined character set is selected Only the LSB of n is applicable When the user defined character set is canceled the internal character set is automatically selected n 0 3 PRINTER FUNCTIONS Reference 1B 26 1B 3F Example 1B 26 y c1 c2 1 d1 d y x x1 xkd1 d y x xk Name Defines user defined characters Format ASCII ESC amp y c1 c2 Hex 1B 26 y c1 c2 Decimal 27 37 y c1 c2 Range y 3 32 lt 1 lt 2 lt 126 0 lt lt 14 Font 14 24 0 lt lt 10 Font 10 x24 0 lt x lt 8 Font 8 24 0 lt 41 lt 255 k c2 c1 1 Description Defines user defined characters Y specifies the number of bytes in the vertical direction C1 specifies the beginning character code for the definition and C2 specifies the final code X specifies the number of dots in the horizontal direction Notes The allowable character code range is from ASCII 20 32 to 7E 126 95 characters Itis possible to define multiple characters for consecutive character codes If only one character is desired use c1 c2 If c2 lt c1 the command is not executed dis the dot data for the characters The dot pattern is in the horizontal direction starting from the left Any remaining dots on the right remain blank The data to define a user defined character is x x y
53. etect Printer ON active at level RS232 high 2 TXD Output RXD Receive data Serial output from Host 3 RXD Input TXD Transmit data Serial data input towards Host 4 N C N C Not connected 5 GND GND Ground signal 6 DSR Output DSR Data Set Ready Printer on and operating active at RS232 level high 7 N C N C Not connected 8 RTS OUT CTS Clear to send Ready to receive data active at RS232 high level 9 N C N C Not connected CUSTOM 2 1 TPL 80 82 5 2 INTERFACES The following diagrams show examples of connections between the printer and the Personal Computer using 25 and 9 pin female connectors Fig 2 2 DCD RXD TXD SIGNAL GND DSR CTS OMAN DOA AO N gt AO N gt 7 Oo TPL 80 82 5 S Fig 2 3 DCD TXD RXD 11 O2 O4 O5 16 O7 8 019 110 O11 O12 O13 O14 O15 16 O17 C 18 O19 20 21 0 22 O 23 O 24 25 TPL 80 82 5 S PC CTS DSR SIGNAL GND AO N gt 2 INTERFACES 22 PARALLEL CENTRONICS Fig 2 4 FRE T Z e C n i n PARALLEL 43 1 ooooooooooo oooooooooo 25 14 The printer has a Cen
54. ex Decimal 0 Off 00 0 On 01 1 Function Paper roll end sensor enabled Paper roll near end sensor enabled RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED NIJA 1 1 When a near paper end is detected printing stops after printing the current line and feeding the paper The paper roll near end sensor is enabled when either bit O is 1 This setting is not cleared by printer resetting because it is stored in the Eeprom n 0 TPL 80 82 5 Name Format Range Description Notes Default Reference Example 1B 64n Name Format Range Description Notes Default Reference Example 1B 66 n Name Format Description Notes Default Reference Example 3 PRINTER FUNCTIONS 1B 43 35 n Enable disable front panel buttons ASCII ESC c 5 n Hex 1B 63 35 n Decimal 27 99 53 n 0 lt lt 255 Enables disables the buttons on the front panel When the LSB of n is 0 the panel buttons are enabled When the LSB of nis 1 the panel buttons are disabled Only the LSB of nis effective On the printer the panel buttons are LINE FEED and FORM FEED When the panel buttons are disabled the buttons may only be used after the printer has been reset When the panel buttons are disabled they re available only during the reset procedure n 0 Print and feed paper n lines
55. ey 7 Line Feed Key 8 Paper input TABLE OF CONTENTS INTRODUCTION MANUAL CONTENTS 2 CR cance 1 EXPLANATORY NOTES USED IN THIS MANUAL 00 1 GENERAL SAFETY INFORMATION 5 5 tet ette deer ern orn etra un nn ra d decere ee e ere EY Ee veda 1 UNPACKING THE PRINTER 2 2 PRINTER FEATURES e egeret geret etre 2 PRINTER DESCRIPTION 3 1 INSTALLATION AND USE 11 1 1 17 7 Zee 1 1 NIME 1 1 1 3 CONFIGURATION 1 3 TA HEXADECIMAL DUMP cesta n under eh ta reu vii ge Ya ne dee neem 1 3 1 5 zie 1 4 1 5 1 Changing the paper roll e 1 4 1 5 2 Using adaptation stirrup for 80mm paper width 1 6 2 INTERFACES 27 VRSZ3Z SERIAL EEUU 2 1 2 2 PARALLEL CENTRONIGS eter enn nte Expo Ene e Penna ccetedsnseatetacdadeceaddvedadadsceusadadensesedauatecnioenasnaadectees 2 3 EXE 2 4 3 PRINTER FUNCTIONS 3 1 PRINTING 5 279 3 1 3
56. f the next line Horizontal tab positions are set using 1B 44 Default Reference 1B 44 Example 0A Name Print and line feed Format ASCII LF Hex 0A Decimal 10 Description Prints the data in the buffer and feeds one line based on the current line spacing Notes Sets the print position to the beginning of the line Default Reference 1B 32 1B 33 Example 0D Name Print and carriage return Format ASCII CR Hex 00 Decimal 13 Description When autofeed is CR enabled this command functions in the same way as 0A 3 33 TPL 80 82 5 3 PRINTER FUNCTIONS otherwise it is disregarded Notes This command sets the print position to the beginning of the line Default Reference 0A Example 10 04 n Name Real time status transmission Format ASCII DLE EOT n Hex 10 04 n Decimal 16 4 n Range 1 lt n lt 4 n 20 Description Transmits the selected printer status specified by n in real time according to the following parameters n 1 transmit printer status n 2 transmit off line status n 3 transmit error status n 4 transmit paper roll sensor status n 20 transmit FULL STATUS Notes This command is executed when the data buffer is full This status is transmitted whenever data sequence 10 04 n is received 1 n 4 Default Reference See tables below Example n 1 Printer status Bit Off On Hex Decimal Function RESERVED RESERVED
57. gh 1D 63 In count down mode if the counter value specified by this command goes out of the counter operation range specified by 1D 43 31 or 1D 43 3B it is forced to convert to the maximum value through 1D 63 nL 1 nH 0 1D 43 30 1D 43 31 1D 43 3B 1D 63 1D 43 3B sa 3B sb 3B sn 3B sr 3B sc 3B Name Format Range Description Select count mode ASCII GS C sb sn sr SC Hex 1D 43 3B sa 3B sb 3B sn 3B sr 3B sc 3B Decimal 29 67 59 sa59 sb 59 sn 59 sr 59 sc 59 0 sa sb sc lt 65535 0 sn sr lt 255 These values are all character strings Selects a count mode for the serial number counter and specifies the value of the counter sa Sb sn sr and sc are all displayed as ASCII characters using codes from 0 to 9 3 23 TPL 80 82 5 3 PRINTER FUNCTIONS sa and sb specify the counter range snindicates the unit amount for counting up or down srindicates the repetition number when the counter value is fixed sc indicates the counter value Notes Count up mode is specified when lt sb and sn 0 and sr z 0 Count down mode is specified when sa gt sb and sn 0 and sr 0 Counting stops when sa sbor sn 0orsr 0 In setting count up mode the minimum value of the counter is sa and the maximum value is sb If counting up reaches a value exceeding the maximum it resets to the minimum value If the counter value set by sc is o
58. graphic page is 76x215 16340 the others 44 bytes 80x204 16320 the others 64 bytes must be sent but are not important indicates TPL 80 indicates TPL 82 5 n 0 Sets font ASCII ESC R n Hex 1B 52 n Decimal 27 82 n 0 lt lt 12 It sets the font currently being used This setting is maintained until new command given or the machine is reset 01 Font 8x16 02 Font 16x24 03 Font 24x32 n 0 TPL 80 82 5 3 12 CUSTOM 1B 53 n Name Format Description Notes Default Reference Example 1B 55 Name Format Description Notes Default Reference Example 1B 56 Name Format Description Notes Default Reference Example 3 PRINTER FUNCTIONS Sets paper sensibility ASCII ESC 5 n Hex 1B 53 n Decimal 27 83 n It sets the paper sensibility currently in used This setting is maintained until a new command is given or the machine is reset n 00 High n 01 Normal n 02 Medium n 03 Low n 04 Double copy Sets underlined mode ASCII ESC U n Hex 1B 55 n Decimal 27 85 n Sets or cancels the underline printing mode n 0 Normal print lt gt 0 Underlined mode Sets the print mode rotated by 90 ASCIl ESC n Hex 1B 56 n Decimal 27 86 n Sets or cancels the 90 printing flag rotation in according to n n 0 Normal print lt gt 0 Rotated print The printing direction depends of the reverse
59. he feed connector has been damaged Liquid has seeped inside the printer The printer has been exposed to rain or water The printer is not functioning normally despite the fact that all instructions in the users manual have been followed The printer has been dropped and its outer casing damaged Printer performance is poor The printer is not functioning Dor CUSTOM 1 TPL 80 82 5 INTRODUCTION UNPACKING THE PRINTER Remove the printer from its carton being careful not to damage the packing material so that it may be re used if the printer is to be transported in the future Make sure that all the components listed below are present and that there are no signs of damage If there are contact Customer Service Upper foam packing shell Paper roll 80 82 5 Manual or CD Rom Paper adaptation stirrup for 80mm Printer 4 Lower foam packing shell m Box NOaRWN gt Open the printer packaging Remove the paper roll the manual or CD Rom and paper adaptation stirrup Take out the upper foam packing shell Take out the printer Keep the box trays and packing materials the event the printer must be transported shipped in the future PRINTER FEATURES The printer is comprised of printers designed to emit high resolution thermal printed tickets ideal for use in information and multimedia kiosks self service machines no queue systems parking areas gaming machines and toll receipt
60. icket length is m 256 1 vertical motion unit inches Max ticket length recommended is 20cm 8 ticket presenting with m steps 1 step 12 mm m must be sent with n 3 7 must be sent with n 7 if n 3 and ticket is not cut yet before execute the command a total cutting will be make if n 0 the fixed value of ticket presenting is on power on and after a reset command both hardware and software 47mm the last distance saved to a 1D 65 3 or 1D 65 8 commands Ticket presenting lenght can change of 12 mm The minimum ticket presenting lenght is 89 mm below tihs value the ticket espulsion could have some problems 1D 6B Name Format Range Description Notes Default Reference Example Set bar code height ASCII GS h n Hex 1D 68 n Decimal 29 104 n 1 lt n lt 255 Sets the height of the bar code n specifies the number of vertical dots n 96 12 1D 6B 3 27 TPL 80 82 5 3 PRINTER FUNCTIONS 1D 6B n lt HRI gt CR Name Formato Range Description Notes Default Reference Example 1D 76 Name Format Description Prints bar code ASCII GS k n lt HRI gt CR Hex 1D 6B n lt HRI gt OD Decimale 29 107 n lt HRI gt 13 1 lt n lt 7 Prints a bar code The value of n selects the bar code type to print n 1UPC E n 2EAN 13 n 3EAN8 n 4 CODE 39 max 12 characters n 5ITF Interleaved 2 of 5 max
61. ion indicates the representation of the command hexadecimal value for example 40 means HEX 40 indicates an ASCII character not performable are optional parameters that can have different values COMMAND DESCRIPTION TABLE Tab 3 2 10 04 n DLEEOTn Real time status transmission SC 1B 26 y c1 c2 ESC amp yc1 c2 Define user defined characters oo ESC mnL nH d1 dk Select image print mode 1B 2D n ESC n Turn underline mode on off 1B 30 ESC 0 Select 1 8 inch line spacing 1B 32 ESC 2 Select 1 6 inch line spacing 1B 33 n ESC 3n Set line spacing using minimum units 1B 34 n ESC 4n Set reset script mode 1B 3D n ESC Select device 1B 3F n ESC n Cancel user defined characters 1B 40 ESC Initialize printer 1B 44 n1 nk 00 ESC D n1 nk NUL Set horizontal tab positions CUSTOM 3 31 TPL 80 82 5 3 PRINTER FUNCTIONS HEX ASCII Description 1B 45 n ESCE n Select emphasized mode 1B 47 n ESC Gn Select double strike mode 1B 4A n ESCJn Print and feed paper 1B 52 n ESC Rn Select international character set 1B 56 n ESC Vn Select print mode 90 turned 1B 5C nL nH ESC nH Set relative print position 1B 61 n ESC an Select justification 1B 63 34 n ESC c4n Select paper sensor for printing in
62. is ignored When the starting position is specified by n motion units to the right nL nH x 256 n When the starting position is specified by n motion units to the left negative direction use the complement of 65536 nL nH x 256 2 65536 n If setting exceeds the printing area width the left or right margin is set to the default value Default Reference Example TPL 80 82 5 3 14 CUSTOM ESCan Name Format Range Description Notes Default Reference Example 1B 63 34 n Name Format Range Description Notes Default Reference Example 3 PRINTER FUNCTIONS Select justification ASCII ESC a n Hex 1B 61 n Decimal 27 97 n 0 lt lt 2 48 lt lt 50 Aligns all data in one line to the specified position n selects the type of justification as follows n Justification 0 48 Flush left 1 49 Centered 2 50 Flush right This command is only enabled when inserted at the beginning of a line Lines are justified within the specified printing area Spaces set by 1B 24 and 1B 5C will be justified according to the previously entered mode n 0 Flush left Centered Flush right ABC ABC ABC ABCD ABCD ABCD ABCDE ABCDE ABCDE Select paper sensor to stop printing ASCII ESC c 4 n Hex 1B 63 34 n Decimale 27 99 52 n 0 lt lt 255 Selects the paper sensor used to stop printing when a near paper end is deleted using n as follows Bit Off On H
63. isabled Print Mode Normal Panel key Enabled Height Mode 1 Print Mode Normal Width Mode x 1 Height Mode jx 1 Justification Left Width Mode jx 1 Character set U S A Justification Left Font Dimension 16x24 28 col Font Dimension 16x24 28 col Speed Quality Normal Speed Quality Normal Current Normal Current Normal Paper autoload Enabled Paper autoload Enabled Reset buffer At Paper End Reset buffer At Paper End Print Density Normal Print Density Normal FF Key to enter setup FF Key to enter setup LF Key to skip setup LF Key to skip setup Fig 1 2 Fig 1 3 TPL 80 82 5 1 2 1 INSTALLATION AND USE 1 3 CONFIGURATION This printer permits the configuration of default parameters The printer s configurable parameters are Printer emulation ESC POS CUSTOM TPT 2 If serial interface is present Baud Rate 57600 38400 19200 9600 4800 2400 1200 Data length 7 8 bits char Parity None even or odd Handshaking XON XOFF Por Hardware If parallel interface is present Select line Select 2 Ticket Present Paper Low Fault line Error P Ticket Present Paper Low USB address N 0 2 1 2 3 4 5 6 7 8 9 USB Status Monitor Activated deactivated 2 Autofeed CR deactivated P or CR activated Panel keys Activated P or deactivated Print mode Normal or Reverse Height mode x1 2 x2 or x4 Width mode x1 x2 or x4
64. jector byte status Bit Off On Hex Decimal Function 0 Off 00 0 Not near paper end On 01 1 Near paper end 1 Off 00 0 Fixed to 0 2 Off 00 0 Paper end sensor On 04 4 Paper is present Off 00 0 Tickets out 08 8 Ticket present ejector mouth 4 Off 00 0 Printer stepping motor off On 10 16 Printer stepping motor on Off 00 0 Ejector motor off 20 32 Ejector motor on Off 00 0 No error 40 64 Error occurs 7 Off 00 0 Fixed to 0 n 7 7 sets maximum ticket length The maximum ticket length is m 256 vertical motion unit inches Max ticket length recommended is 20cm n 8ticket presenting with m steps 1 step 12 mm Notes m must be sent with n 3 7 must be sent with n 7 if n 3 and ticket is not cut yet before execute the command a total cutting will be make TPL 80 82 5 3 60 CUSTOM Default Reference Example 1D 66 n Name Format Range Description Notes Default Reference Example 1D 68 n Name Format Range Description Notes Default Reference Example 3 PRINTER FUNCTIONS if n 0 the fixed value of ticket presenting is on power on and after a reset command both hardware and software 47mm the last distance saved to a 1D 65 3 or 1D 65 8 commands Ticket presenting lenght can change of 12 mm The minimum ticket presenting lenght is 8
65. k even number 48 lt d 57 48 lt d lt 57 65 lt d1 lt 68 36 6 CODABAR 1 lt k 43 45 46 47 58 7 CODE93 1 lt k lt 255 1 lt d lt 127 8 CODE128 2 lt k lt 255 1 lt d lt 127 20 CODE32 8 lt k lt 9 48 lt d lt 57 65 UPC A 11 lt lt 12 48 lt lt 57 66 UPC E 11 lt lt 12 48 lt d lt 57 67 EAN13 JAN 12 lt n lt 13 48 lt d lt 57 68 EANS JAN 7 lt n lt 8 48 lt d lt 57 48 lt lt 57 65 lt d lt 90 32 69 CODE39 1 lt n lt 255 36 37 43 45 46 47 70 ITF 1 lt n lt 255 48 lt d lt 57 48 lt d lt 57 65 lt d1 lt 68 36 71 CODABAR 1 lt n lt 255 43 45 46 47 58 72 CODE93 1 lt n lt 255 0 lt 4 lt 127 73 CODE128 2 lt n lt 255 0 lt 4 lt 127 90 CODE32 8 lt lt 9 48 lt d lt 57 Notes If d is outside of the specified range the printer prints the following message BAR CODE GENERATOR IS NOT OK and processes the data which follows as normal data If the horizontal size exceeds the printing area the printer only feeds the paper This command feeds as much paper as is required to print the bar code regardless of the line spacing specified by 1B 32 or 1B 33 After printing the bar code this command sets the print position to the beginning of the line This command is not affected by print modes emphasized double strike underline TPL 80 82 5 3 62 CUSTOM 3 PRINTER FUNCTIONS Notes per Notes per 2 or character size except for upside down and justification mode This command e
66. l cut 1B 6D Name Format Description Notes Default Reference Example 1B 74n Name Format Range Description Notes Default Reference Example 1B 76 Name Format Description 3 PRINTER FUNCTIONS Partial cut ASCII ESC m Hex 1B eD Decimal 27 109 This command enables partial cutter operation If there is no cutter a disabling flag is set and any subsequent cut commands will be ignored The printer waits to complete all paper movement commands before it executes a partial cut Select character code table ASCII ESC t n Hex 1B 74 n Decimal 27 116 n 0 19 255 Selects a page n from the character code table as follows n Page 0 0 PC437 U S A Standard Europe 19 19 PC858 for Euro symbol at position 213 255 Space page n 0 See character code tables For printing Euro symbol the command sequence is 1B 74 13 D5 Transmit paper sensor status ASCII ESC V Hex 1B 76 Decimal 27 118 When this command is received transmit the current status of the paper sensor The status to be transmitted is shown in the table below Bit Off On Hex Decimal Function 0 1 Off 00 0 Paper is present On 03 3 Near paper end 23 Off 00 0 Paper end sensor Paper is present On 0C 12 Paper end sensor Paper is not present 4 RESERVED 5 RESERVED 6 RESERVED 7
67. l 29 118 Description This command transmits two bytes each bit indicates the printer status to serial port First byte Bit Off On Hex Decimal Function 0 Off 00 0 Paper presence in abundance On 01 1 Near paper end 1 RESERVED 2 Off 00 0 Paper out On 04 4 Paper presence 3 Off 00 0 Line Feed key released On 08 8 Line Feed key pressed 4 Off 00 0 Form Feed key released On 10 16 Form Feed key pressed 5 Off 00 0 Head temperature correct On 20 32 Head temperature error 6 Off 00 0 Motor off On 40 64 Motor on 7 Off 00 0 No error On 80 128 Error due to paper end Head up etc TPL 80 82 5 3 64 CUSTOM Notes Default Reference Example 10 77 n Name Format Range Description Notes Default Reference Example 1D 7C n Name Format Range Description 3 PRINTER FUNCTIONS Second byte Bit Off On Hex Decimal Function 0 On 01 1 Printing 1 On 02 2 Head up 2 RESERVED 3 On 08 8 Ticket on the exit mouth 4 RESERVED 5 RESERVED 6 RESERVED 7 RESERVED This command is executed immediately even when the data buffer is full Busy 10 04 Set bar code width ASCII GS w n Hex 1D 77 n Decimal 29 119 n 1 lt n lt 6 Sets the horizontal size of the bar code n specifies the bar code width as follows n Module width mm 1 0 125 2 0 25 3 0 375 4 0 5 5 0 625 6
68. machines The printer offers a wide range of options in addition to normal print features e Ticket width 80 82 5 mm High speed printing 130mm sec Interfaces RS232 USB optional CENTRONICS parallel ESC POS and CUSTOM TPT emulation Bar code UPC A UPC E EAN13 EAN8 CODE39 ITF CODABAR CODE93 CODE128 and CODE32 INTRODUCTION 6 standard and international character set fonts Completely or partially programmable fonts Double width height quadruple width height expanded italic rotated 90 180 and 270 Receive buffer 16Kbytes Definition of function macros for automatic operation repetition Internal programmable counter Graphic print mode Print density ESC POS Emulation 6 programmable logos 640 x 215 each dots CUSTOM TPT Emulation 3 programmable logos 640 x 431 each dots Anti jamming and near paper end sensors Paper cutter PRINTER DESCRIPTION The printer fig 1 is comprised of a metal frame 1 paper roll holder 2 printing mechanism 3 and cutter 4 The following keys are located on the control panel FORM FEED 5 LINE FEED 6 Power On LED 7 Paper Low LED 8 and Status LED 9 Fig 1 e When the LINE FEED 6 key is pressed the printer advances the paper so that it may be inserted manually in the printing mechanism During power up if the LINE FEED key is held down the printer will perform the FONT TEST routine e fthe FORM FEED 5 ke
69. mm CUSTOM TPT EMULATION Number of columns TPL 80 model TPL 82 5 model 9 9 Characters L x H mm TPL 80 82 5 4 2 CUST M 4 TECHNICAL SPECIFICATIONS 4 2 DIMENSIONS Front view B section view B M 1 N e 22 Fig 4 1 Side view 180 3 130 ul ry 1 T 1 d N A P C 5 E a PY NI printer Pore oO T T Y Y Y 19 5111 igh 88 1 129872 8 L 105 2 5 L 180 1 2127 Fig 4 2 287 7 1 CUSTOM 4 3 TPL 80 82 5 4 TECHNICAL SPECIFICATIONS Tap view 168 Fig 4 3 150 90 k pt 180 150 150 e 15 a A pa Lai 47 7 000000003
70. n Hex 1D 21 Decimal 29 33 n 0 lt lt 255 Selects character height width as follows 3 52 CUSTOM 3 PRINTER FUNCTIONS Bits 0 to 3 to select character height see table 2 Bits 4 to 7 to select character width see table 1 Table 1 Character Width selection Table 2 Character Height selection Hex Decimal Width Hex Decimal Height 00 0 1 normal 00 0 1 normal 10 16 2 double width 01 1 2 double height 20 32 3 quadruple width 02 2 3 quadruple height 30 48 03 3 40 64 04 4 50 80 05 5 60 96 06 6 70 112 07 7 Notes This command is effective for all characters except HRI characters If n falls outside the defined range this command is ignored e Characters enlarged to different heights on the same line are aligned at the baseline or topline see 1D 7E 1B 21 can also be used to select character size However the setting of the last received command is the effective one Default n 0 Reference 1B 21 Example 1D 3A Name Start end macro definition Format ASCII GS Hex 1D 3A Decimal 29 58 Description Notes Default Reference Example 10 42 n Name Format Starts or ends macro definition Macro definition starts when this command is received during normal operation When 1D 5E is received during macro definition the printer ends macro definition and clears all definiti
71. nds with a NUL code When the bar code system used is UPC A or UPC E the printer prints the bar code data after receiving 11 without check digit or 12 with check digit bytes bar code data When the bar code system used is EAN13 the printer prints the bar code data after receiving 12 without check digit or 13 with check digit bytes bar code data When the bar code system used is EAN8 the printer prints the bar code data after receiving 7 without check digit or 8 with check digit bytes bar code data The number of data for ITF bar code must be even numbers When an odd number of data is input the printer ignores the last received data If nis outside of the specified range the printer stops command processing and processes the following data as normal data When CODE93 is used The printer prints an HRI character o as a start character at the beginning of the HRI character string The printer prints an HRI character o as a stop character at the end of the HRI character string The printer prints an HRI character n as a control character 00 to 1F and 7F When CODE 128 is used When using CODE 128 in this printer please note the following regarding data transmission The top part of the bar code data string must be a code set selection character CODE A CODE B or CODE C which selects the first code set Special characters are defined by
72. ode width ASCII GS Ww n Hex 1D 77 n Decimal 29 119 n 2 lt n lt 6 Sets the horizontal size of the bar code n specifies the bar code width as follows n Module width mm 2 0 25 3 0 375 4 0 5 5 0 625 6 0 75 3 1D 6B Enable disable automatic FULL STATUS back ASCII GS Q n Hex 1D EO n Decimal 29 224 n 0 lt lt 255 Enable disable automatic full status back nspecifies the composition of FULL STATUS as follows 3 29 TPL 80 82 5 3 PRINTER FUNCTIONS Bit Off On Hex Decimal Function 0 Off 00 0 Disable Paper status On 01 1 Enable Paper status 1 Off 00 0 Disable User status On 02 2 Enable User status 2 Off 00 0 Disable Recoverable Error Status On 04 4 Enable Recoverable Error Status 3 Off 00 0 Disable Unrecoverable Error Status On 08 8 Enable Unrecoverable Error Status 4 RESERVED 5 RESERVED 6 RESERVED 7 RESERVED Notes Once enable at least one byte of the FULL STATUS for each change of at least one of the bits which compose the required status the status sent in automatic from the printer will be so composed as follows 1 Byte 10 DLE 2 Byte n Next byte depends how many bits are active in n Reference Example 1D E2 Name Reading number of cuts performed from the printer Format ASCII GS Hex 1D E2 Decimal 29 226 Description Notes
73. on 0 Off 00 0 Paper present On 01 1 Paper not present 1 RESERVED 2 Off 00 0 Paper present in abundance On 04 4 Near paper end 3 RESERVED 4 RESERVED 5 RESERVED 6 Off 00 0 Not virtual paper end 9 On 40 64 Virtual paper end 7 RESERVED Virtual paper end is set when the paper length available readed by GS 0 is 0 CUSTOM 3 35 TPL 80 82 5 3 PRINTER FUNCTIONS 18 Name Format Description 4 byte USER STATUS Bit Off On Hex Decimal Function 0 Off 00 0 Thermal head down On 01 1 Thermal head up 1 RESERVED 2 RESERVED 3 Off 00 0 Drag paper motor off On 08 8 Drag paper motor on 4 RESERVED 5 Off 00 LF key released On 20 32 LF key pressed 6 Off 00 0 FF key released On 40 64 FF key pressed 7 RESERVED 5 byte Recoverable error Status Bit Off On Hex Decimal Function 0 Off 00 0 Head temperature ok On 01 1 Head temperature error 1 RESERVED 2 RESERVED 3 Off 00 0 Power supply voltage ok Off 00 0 Power supply voltage error 4 RESERVED 5 Off 00 Acknowledge command On 20 32 Not acknowledge command error 6 Off 00 0 Free paper route On 40 64 Paper jam 7 RESERVED 6 byte Unrecoverable error Status Bit Off On He
74. ons e Macros are not defined when power is turned on to the machine Macro content is not cancelled by the 1B 40 command Therefore 1B 40 may be included in the content of macro definitions If the printer receives 1D 3A a second time after previously receiving 1D 3A the printer remains in macro undefined status The contents of the macro can be defined up to 2048 bytes If the macro definition exceeds 2048 bytes excess data is not stored 1D 5E Turn white black reverse printing mode on off ASCII GS B n Hex 1D 42 n Decimal 29 66 n CUSTOM 3 53 TPL 80 82 5 3 PRINTER FUNCTIONS Range 0 lt lt 255 Description Turns white black reverse printing mode on or off When the LSB of n is 0 white black reverse printing is turned off When the LSB of n is 1 white black reverse printing is turned on Notes e Only the LSB of n is effective This command is available for both built in and user defined characters This command does not affect bit image downloaded bit image bar code HRI characters and spacing skipped by 09 1B 24 and 1B 5C This command does not affect white space between lines White black reverse mode has a higher priority than underline mode Even if underline mode is on it will be disabled but not cancelled when white black reverse mode is selected Default n 0 Reference Example 1D 43 30 nm Name Select counter print mode Format ASCII GS C 0 n m Hex 1
75. ort the characters are printed out both as hexadecimal codes and ASCII codes Once the self test routine has finished the printer enters Hexadecimal Dump mode The printer remains in CUSTOM 1 3 TPL 80 82 5 1 INSTALLATION AND USE standby until a key is pressed or characters are received through the communication port For every 10 characters received the hexadecimal and corresponding ASCII codes are printed out if the characters are underlined the receive buffer is full Shown below is an example of a Hexadecimal Dump 48 6 78 61 64 6 6 69 D 61 Hexadecima eC 20 64 75 6D 70 20 66 75 6E 1 dump fun 63 74 69 6F 20 30 31 32 33 ction 0123 34 35 36 37 385 39 61 62 63 64 456789abcd 65 66 67 68 69 6A 6B 6C 6D 6E efghijklmn 6F 70 71 72 73 74 75 76 77 78 opqrstuvwx 79 2 1 5 MAINTENANCE 1 5 1 Changing the paper roll Depending on how the printer Paper Autoload parameter is set one of two procedures must be followed If enabled Position the paper roll 1 so that it unrolls correctly as shown in fig 1 4 insert the paper into the infeed slot 2 and wait for the roll to load automatically If not enabled proceed as follows 1 Position the paper roll 1 so that it unrolls correctly as shown in fig 1 4 2 Raise the print head by lifting the lever 4 in the direction indicated by the arrow as shown in fig 1 5 3 Insert the end of the paper roll into the infeed slot 2 and have it pass beyond the print head 4 L
76. ounter range nindicates the unit amount when counting up or down rindicates the repetition number when the counter value is fixed Count up mode is specified when aL aH x 256 lt bL bH x 256 and n 0 and 0 Count down mode is specified when aL aH x 256 gt bL bH x 256 and n 0 and rzO Counting stops when aL aH x 256 bL x 256 orn 2 or r 0 Setting the count up mode the minimum counter value is aL aH x 256 and the maximum value is bL bH x 256 If the counting up reaches a value that exceeds the maximum it resets to the minimum value Setting the count down mode the maximum counter value is aL aH x 256 and the minimum value is bL 65 x 256 If the counting down reaches a value less than the minimum it resets to the maximum value When this command is executed the internal count that indicates the repetition number specified by ris cleared aL 1 aH 0 bL 255 bH 255 n 1 r 1 1D 43 30 1D 43 32 1D 43 3B 1D 63 Set counter ASCII GS C 2 nL nH Hex 1D 43 32 nL nH Decimal 29 67 50 nL nH O lt nL nH lt 255 Sets the serial number counter value nL and nH determine the value of the serial number counter set by nL nH x 256 In count up mode if the counter value specified by this command goes out of the counter operation range specified by 1D 43 31 or 1D 43 3B it is forced to convert to the minimum value throu
77. ower the head lever and press the LINE FEED key so that the paper will feed a few centimeters out of the printer 3 PRINTER SECTION VIEW Wes iw Fig 1 4 E i Ur TPL 80 82 5 1 4 CUSTOM 1 INSTALLATION AND USE Fig 1 5 N ATTENTION Fig 1 6 Before inserting the paper make sure it is cut cleanly NOTE the changing paper procedure is the same for all the printer models avalaible CUSTOM 1 5 TPL 80 82 5 1 INSTALLATION AND USE 1 5 2 Using adaptation stirrup for 80 mm paper width 1 Extract the pivot by unscrewing the screw as shown in fig 1 7 Fig 1 7 2 Fig 1 8 TPL 80 82 5 1 6 CUSTOM 1 INSTALLATION AND USE 3 Re assemble the pivot inside the two stirrup and fixing itself with the two screw as shown in fig 1 9 Fig 1 9 CUSTOM 1 7 TPL 80 82 5 2 INTERFACES 21 RS232 SERIAL Fig 2 1 SERIAL The printer has an RS232 serial interface and is connected by means of a 9 pin female connector see fig 2 1 In the following table the signals present on the connector are listed PIN SIGNAL DIRECTION TO DESCRIPTION Tab 2 1 1 DCD Output DCD Data Carrier d
78. owever the value cannot be less than the minimum horizontal movement amount and it must be in even units of the minimum horizontal movement amount Default If 40 and 56 col nL nH 0 If 72 col nL 14 nH 0 Reference Example 10 5E rtm Name Execute macro Format ASCII GS r t m Hex 1D t m Decimal 29 94 r t m Range O lt r t lt 255 0 lt lt 1 Description Executes a macro rspecifies the number of times to execute the macro t specifies the waiting time for executing the macro The waiting time is t x 100 msec for each macro execution m specifies macro executing mode When the LSB of m 7 0 the macro is executed rtimes continuously at the interval specified by t When the LSB of m 1 after waiting for the period specified by t the LED indicator blinks and the printer waits for the FEED button to be pressed After the button is pressed the printer executes the macro once The printer repeats the operation rtimes Notes This command has an interval of tx 100 msec after a macro is executed by t If this command is received while a macro is being defined the macro definition is aborted and the definition is cleared If the macro is not defined or if ris 0 nothing is executed When the macro is executed by pressing the FORM FEED button m 1 the paper cannot be fed using the FORM FEED button Default Reference 1D 3A Example 1D 63 Name Print counter Format A
79. per sensibility The current paper sensibility in use is also changed Copy flash bank into ram bank 16kbytes ASCII ESC F n Hex 1B 46 n Decimal 27 70 n 1 lt n lt 6 The value of n determines flash bank n 1 1 bank n 2 27 bank n 3 3 bank n 4 4 bank n 5 5 bank n 6 6 bank ifn 0 orn gt 6 the command is ignored Turn double strike mode On Off ASCII ESC G n Hex 1B 47 n Decimal 27 71 n 0 lt lt 255 Turn double strike mode or Off When the LSB of nis 0 double strike mode is turned off When the LSB of n is 1 double strike mode is turned on Only the LSB of n is active Printer output is the same in double strike mode and emphasized mode n 0 3 11 TPL 80 82 5 1B 4E n Name Format Description Notes Default Reference Example 1B 50 Name Format Description Notes Default Reference Example 1B 52n Name Format Range Description Notes Default Reference Example 3 PRINTER FUNCTIONS Sets negative mode ASCII ESC N n Hex 1B 4E n Decimal 27 78 n Sets or cancel printing negative mode n 0 Normal print lt gt 0 Negative print n 0 Fill ram bank from port ASCII ESC 16384 bytes Hex 1B 50 16384 bytes Decimal 27 80 16384 bytes This command can transfer graphic page into ram O80 bytes is an horizontal dotline of 608 640 dots for 8215 204 dotlines The number of bytes that make
80. printer setting The meaning of these bytes depends on the n parameter with n 0 Byte 1 Bit 1 Bit 0 Function Description 0 0 Normal H mode 0 1 Double H mode 1 0 Quadruple H mode 1 1 Not used H mode Bit Bit 2 Function Description 0 0 Normal V mode 0 1 Double V mode 1 0 Quadruple V mode 1 1 Not used V mode TPL 80 82 5 3 8 CUSTOM 3 PRINTER FUNCTIONS Bit 4 Function Description Not used Bit 5 Function Description 0 S ipt 1 Su mE Superscript Subscript Bit 6 Function Description 0 Reverse OFF Beis 1 Reverse ON Bit 7 Function Description 0 Rotation OFF Rotation 1 Rotation ON Byte2 Bit 0 Function 0 Cutter enabled 1 Cutter disabled Bit 1 Function 0 Paper end enabled 1 Paper end disabled Bit 2 Function 0 Form Feed enabled 1 Form Feed disabled Bit 3 Function 0 Autofeed enabled 1 Autofeed disabled Bit4 Function 0 Font 24x32 1 Font 8x16 or Font 16x24 Bit 5 Bit 6 Bit 7 Function Not used with n 21 Byte 1 Indicates number of line feeds for VTAB Vertical TAB Byte 2 Indicates printing head value with n 22 Byte 1 Byte 2 Description H L Indicates number of dot lines for FORM FEED CUSTOM 3 9 TPL 80 82 5 Byte 1 Notes Default Reference Example 1B 40
81. ror Status On 04 4 Enable Recoverable Error Status 3 Off 00 0 Disable Unrecoverable Error Status On 08 8 Enable Unrecoverable Error Status 4 RESERVED 5 RESERVED 6 RESERVED 7 RESERVED TPL 80 82 5 3 66 CUSTOM Notes Reference Example 1D E2 n Name Format Description Notes Default Reference Example 1D E3 n Name Format Description Notes Default Reference Example 1D E5 Name Format Description Notes Default Reference Example 3 PRINTER FUNCTIONS Once enable at least one byte of the FULL STATUS for each change of at least one of the bits which compose the required status the status sent in automatic from the printer will be so composed as follows 1 Byte 10 DLE 2 Byte n Next byte depends how many bits are active in n 10 04n Reading number of cuts performed from the printer ASCII GS Hex 1D E2 Decimal 29 226 Reading the number of cuts performed from the printer The command return a string that points out how many cuts are performed by the printer for example if there are performed 2376 cuts it will be 2376 cuts Reading of length cm of printed paper ASCII GS Hex 1D E3 Decimal 29 227 Reading of length cm of printed paper The command return a string pointing out how much paper is printed for example if the printer has print about 2515 5 m it will be 251550cm Reading number
82. rt to the minimum value through 1D 63 In count down mode if the counter value specified by this command goes out of the counter operation range specified by 1D 43 31 or 1D 43 3B it is forced to convert to the maximum value through 1D 63 nL 1 nH 0 1D 43 30 1D 43 31 1D 43 3B 1D 63 1D 43 3B sa 3B sb 3B sn 3B sr 3B sc 3B Name Format Range Description Select count mode ASCII GS C sa sb sn sr sc Hex 1D 43 sa sb 3B sn 3B sr sc3B Decimal 29 67 59 sa 59 sb 59 sn 59 sr 59 sc59 0 lt sa sb sc lt 65535 0 lt sn sr x 255 These values are all character strings Selects a count mode for the serial number counter and specifies the value of the counter sa sb sn sr and sc are all displayed as ASCII characters using codes from 0 to 9 3 55 TPL 80 82 5 3 PRINTER FUNCTIONS sa and sb specify the counter range snindicates the unit amount for counting up or down srindicates the repetition number when the counter value is fixed sc indicates the counter value Notes Count up mode is specified when lt sb and sn 0 and sr z 0 Count down mode is specified when sa gt sb sn 0 and sr z 0 Counting stops when sa sbor sn 0orsr 0 In setting count up mode the minimum value of the counter is sa and the maximum value is sb If counting up reaches a value exceeding the maximum i
83. t lt 51 TPL 80 82 5 3 56 3 PRINTER FUNCTIONS Description Transmits the printer ID specified by n follows n Printer ID Specification 1 49 Printer model ID 72 2 50 Type ID See table below 3 51 ROM version ID Depends on ROM version 4 character n 7 2 Type ID Bit Off On Hex Decimal Function 0 Off 00 0 2 byte character codes not supported 1 Off 00 0 Autocutter not equipped Autocutter equipped 2 Off 00 0 Non label thermal paper On 04 4 Label thermal paper 3 Undefined 4 RESERVED 5 RESERVED 6 RESERVED 7 RESERVED Notes When the DTR DSR control is selected the printer only transmits 1 byte printer ID without confirmation that the host is ready to receive data If host is not ready the printer waits until is ready When the XON XOFF control is selected the printer only transmits 1 byte printer ID without confirmation that the host is ready to receive data This command is executed when the data is processed in the data buffer Therefore there could be a time lag between command reception and data transmission depending on data buffer status Default Reference Example 1D 4C nL nH Name Set left margin Format ASCII GS L nL nH Hex 1D 4C nL nH Decimal 29 76 nL nH Range Ox nH lt 255 Description Sets the left margin The left margin is setto nL nH x 256 x horizon
84. t resets to the minimum value If the counter value set by sc is outside the counter operation range the counter value is forced to convert to the minimum value by executing 1D 63 In setting count down mode the maximum value of the counter is sa and the minimum value is sb If counting down reaches a value less than the minimum it resets to the maximum value If the counter value set by sc is outside the counter operation range the counter value is forced to convert to the maximum value by executing 1D 63 Parameters sa to sc can be omitted If omitted they remain unchanged Parameters sa to sc cannot contain characters other than 0 to 9 Default sa 1 sb 65535 sn 1 1 1 Reference 1D 43 30 1D 43 31 1D 43 32 1D 63 Example 1D 48 n Name Select printing position of Human Readable Interpretation HRI characters Format ASCII GS H n Hex 1D 48 n Decimal 29 72 n Range 0 lt lt 3 48 lt lt 51 Description Selects the printing position of HRI characters when printing bar codes n selects the printing positions as follows n Function 0 48 Not printed 1 49 Above the bar code 2 50 Below the bar code 3 51 Both above and below the bar code Notes HRI characters are printed using the font specified by 1D 66 Default n 0 Reference 1D 66 1D 6B Example GS In Name Transmit printer ID Format ASCII GS n Hex 1D 49 n Decimal 29 73 n Range 1 lt lt 3 49 l
85. table below Cp e p 28 ao se 5e so 5e 99 76 76 o n Characters of USA s Fae 15 2 151 81 3 unitedkingdom sjej pi e ip e 4 emai 5 Jeje a EINE NN e tw z Sem 8 sa ee 9 noway 0 oa al m spain2 s a al EIE CN e 81 Default n 0 Reference Example CUSTOM 3 45 TPL 80 82 5 3 PRINTER FUNCTIONS 1B 56 n Name Format Range Description Notes Default Reference 1B 5C nL nH Set 90 rotated print mode ASCII ESC V n Hex 1B 56 n Decimal 27 86 0 lt lt 1 48 lt lt 49 Turns 90 rotation mode on off n is used as follows n Function 0 48 Turns off 90 rotation mode 1 49 Turns on 90 rotation mode When underlined mode is turned on the printer does not underline 90 rotated characters All the same it s possible select the underline mode Double width and double height commands in 90 rotation mode enlarge characters in the opposite directions from double height and double width commands in normal mode This command is not available in Page mode If this command is entered in Page mode the printer all the same save the setting n 0 1B 21 1B 2D Name Format R
86. tal motion unit inches Printable area Yt Left margin Printing area width Notes This command is enabled only if set at the beginning of the line If the setting exceeds the printable area the maximum value of the printable area is used If the left margin printing area width is greater than the printable area the printing area width is set at maximum value CUSTOM 3 57 TPL 80 82 5 Default Reference Example 1D 50 x y Name Format Range Description Notes Default Reference Example 1D 57 nL nH Name Format Range Description Notes TPL 80 82 5 3 58 3 PRINTER FUNCTIONS The horizontal and vertical motion unit are specified by 1D 50 Changing the horizontal or vertical motion unit does not affect the current left margin The 1D 50 command can change the horizontal and vertical motion unit However the value cannot be less than the minimum horizontal movement amount and it must be in even units of the minimum horizontal movement amount If 40 and 56 col nL nH 0 If 72 col nL 14 nH 0 Set horizontal and vertical motion units ASCII GS P X y Hex 1D 50 x y Decimal 29 80 X y x 100 200 y 100 200 Sets the horizontal and vertical motion units to 1 x inch and 1 y inch respectively When x is set to 0 the default setting value is used When y is set to 0 the default setting value is
87. terruption 1B 63 35 n ESC c5n Enable disable front panel buttons 1B 64 n ESC dn Print and feed paper n lines 1B 69 ESC i Total cut 1B 6D ESC m Partial cut 1B 74 n ESC tn Select character code table 1B 76 ESC v Transmit printer status 1B 78n ESC Select speed quality mode 1B 7B n ESC n Set cancel upside down character printing 1 FA nxL xH yHyL ESC nxLxH yHyL Print graphic 1B FB nL nH ESC nL nH Transmit graphic page to communication port 1B n ESC n Transfer flash bank into graphic page 1B FD nL nH ESC nH Receive graphic page from communication port 1B FE n ESC n Transfer graphic page into flash bank 1D 21 n GS n Select character size 1D 3A GS Set start end of macro definition 1D 42 n GS Bn Turn white black reverse printing mode on off 1D 43 30 nm GS COnm Select counter print mode 1D 43 31 aL aH bL bHnr GS C 1aLaH bLbHn Select count mode 1D 43 32 nH GS C 2 nL nH Sets counter 1D 43 3B sa 3B sb 3B sn 3B sr 3B sc 3B GS sa sb sn sr 5 Selects counter mode 10 48 n GSHn Selects HRI print position 1D 49 n GS Transmit printer ID 1D 4C nL nH GS L nL nH Set left margin 1D 50 xy GS P xy Set horizontal and vertical motion units mode 1 10 57 nL nH GS W nL nH Set printing area width 1D 5E rtm GS rtm Exe
88. tronics parallel interface and is connected by means of a 25 pin female connector see fig 2 4 In the following table the signals present on the connector are listed PIN SIGNAL FUNCTION 1 Strobe Strobe input 2 DO Data input bit 0 3 D1 Data input bit 1 4 D2 Data input bit 2 5 D3 Data input bit 3 6 D4 Data input bit 4 7 D5 Data input bit 5 8 D6 Data input bit 6 9 D7 Data input bit 7 10 ACK Acknowledge 11 BUSY Busy 12 PE Paper end 13 SELECT Select Ticket presence Near paper end 14 N C Not connected 15 FAULT Fault Ticket presence Near paper end 16 RESET Printer reset 17 GND GND 18 N C Not connected 19 25 GND GND Tab 2 2 TPL 80 82 5 2 INTERFACES For the parallel connector the connection between printer and Personal Computer must be made with a 25 pin to pin connector 9 NOTE Functions selecting through the parameter setting mode to the start The signals Select and Fault respond to the logic of functioning of the Centronics parallel port The signal Ticket Presence is high if the ticket is present on the mouth of exit the signal Near paper end is high when the RED LED has turned on 2 3 USB qe 4 P i amp 1 D Fig 2 5 Printers with USB serial interface conform to USB 1 0 stan
89. ts the printer ID specified by n follows n Printer ID Specification 1 49 Printer model ID 72 2 50 Type ID See table below 3 51 ROM version ID Depends on ROM version 4 character n 7 2 Type ID Bit Off On Hex Decimal Function 0 Off 00 0 2 byte character codes not supported 1 Off 00 0 Autocutter not supplied On 02 2 Autocutter supplied 2 Off 00 0 Thermal paper w o label On 04 4 Thermal paper with label 3 RESERVED 4 RESERVED 5 RESERVED 6 RESERVED 7 Off 00 0 Custom TPT emulation On 80 128 ESC POS emulation Notes Tthe printer only transmits 1 byte printer ID without confirmation that the host is ready to receive data This command is executed when the data is processed in the data buffer Therefore there could be a time lag between command reception and data transmission depending on data buffer status Default Reference Example 1D 5E rtm Name Execute macro Format ASCII GS r t m Hex 1D 5E r t m Decimal 29 94 r t m Range O lt r t lt 255 0 lt lt 1 Description Executes a macro r specifies the number of times to execute the macro t specifies the waiting time for executing the macro The waiting time is tx 100 msec for each macro execution m specifies macro executing mode When the LSB of m 7 0 the macro is executed rtimes continuously at the interval specified by t
90. uggestions relative to the use of the printer WARNING Information marked with this symbol must be carefully followed to guard against damaging the printer DANGER Information marked with this symbol must be carefully followed to guard against operator injury or damage GENERAL SAFETY INFORMATION Read and keep the instructions which follow Follow all warnings and instructions indicated on the printer Before cleaning the printer disconnect the power supply Clean the printer with a damp cloth Do not use liquid or spray products Do not operate the printer near water Do not use the printer on unstable surfaces that might cause it to fall and be seriously damaged Only use the printer on hard surfaces and in environments that guarantee proper ventilation Make sure the printer is placed in such a way as to avoid damage to its wiring Use the type of electrical power supply indicated on the printer label If in doubt contact your retailer Do not block the ventilation openings Do not introduce foreign objects of any kind into the printer as this could cause a short circuit or damage parts that could jeopardize printer functioning Do not spill liquids onto the printer Do not carry out technical operations on the printer with the exception of the scheduled maintenance procedures specifically indicated in the user manual Disconnect the printer from the electricity supply and have it repaired by a specialized technician when T
91. utside the counter operation range the counter value is forced to convert to the minimum value by executing 1D 63 In setting count down mode the maximum value of the counter is sa and the minimum value is sb If counting down reaches a value less than the minimum it resets to the maximum value If the counter value set by sc is outside the counter operation range the counter value is forced to convert to the maximum value by executing 1D 63 Parameters sa to sc can be omitted If omitted they remain unchanged Parameters sa to sc cannot contain characters other than 0 to 9 Default sa 1 sb 65535 sn 1 1 1 Reference 1D 43 30 1D 43 32 1D 43 31 1D 63 Example 1D 48 n Name Select printing position of Human Readable Interpretation HRI characters Format ASCII GS H n Hex 1D 48 n Decimal 29 72 n Range 0 lt lt 3 48 lt lt 51 Description Selects the printing position of HRI characters when printing bar codes n selects the printing positions as follows n Function 0 48 Not printed 1 49 Above the bar code 2 50 Below the bar code 3 51 Both above the below the bar code Notes Default n 0 Reference 1D 6B Example 1D 49 n Name Transmit printer ID Format ASCII GS n Hex 1D 49 n Decimal 29 73 n Range 1 lt lt 3 49 lt lt 51 TPL 80 82 5 3 24 CUSTOM 3 PRINTER FUNCTIONS Description Transmi
92. value exceeds 640 it is rejected The number of characters to be received is n1 256 n2 In this mode the bytes received are input in the line buffer at the current position of the cursor and in a different order from that of the previous command Let s imagine that a print line consists of an array of 24 rows containing bytes each the characters received after this command will be input starting from the top line and proceeding towards the bottom line After 24 characters the pointer increases and proceeds to the next position At the 676 80 position the line is printed and filling continues on the next line Thanks to this procedure text and graphics can be combined In fact if for example there were any characters present in the print buffer the bytes subsequent to this command would be input in the position immediately after Figure 1 shows a line buffer each box corresponds to 8 dots which on paper correspond to 1 mm both horizontally and vertically To fill the memory completely 1224 1920 bytes are required For example to print a filled bar 608 8640 dots long and 24 dots high send the following command 1B 2B 07 20 1824 FF 1B 2B 07 80 1920 FF buffer position 76 TPL 80 80 TPL 82 5 indicates TPL 80 TPL 82 5 Set reset italic mode ASCII ESC 4 n Hex 1B 34 n De
93. vice in use see fig 1 3 02 NOTE f the printer has an USB interface the serial interface configuration parameters are not displayed 9 NOTE This parameter is displayed if the printer has an USB interface it s used to identify univocally the USB printer by a numerical address code if on the PC are connected two printers with USB interface 0 NOTE This parameter is displayed if the printer has an USB interface The Status Monitor is an additional printing driver component that allows the printer status monitoring It must be enabled only if it was installed the Status Monitor specific driver Model with serial interface Model with USB interface PRINTER SETUP PRINTER SETUP RS232 INTERFAGE 2 USB 2 EEPROM OK EEPROM TEST OK CUTTER TEST OK CUTTER OK TEST ue OK EJECTER AEST OK HEAD TEMPERATURE C 22 5 HEAD TEMPERATURE C 22 5 PAPER PRINTED cm 9860 PAPER PRINTED cm 9860 CUT COUNTER 604 CUT COUNTER 604 POWER ON COUNTER 135 POWER ON COUNTER 135 Printer emulation CUSTOM TPT Printer emulation CUSTOM TPT Baud Rate 0 9600 bps USB Address 9 0 Data length 2 8 bits chr USB Status Monitor Enabled Parity 2 None Autofeed CR disabled Handshaking Xon Xoff Panel key Enabled Autofeed CR d
94. with twice the width of normal characters This command cancels previous tab settings When setting n 8 the print position is moved to column 9 by sending 09 Up to 32 tab positions k 32 can be set Data exceeding 32 tab positions is processed as normal data CUSTOM 3 43 TPL 80 82 5 Default Reference Example 1B 45 n Name Format Range Description Notes Default Reference Example 1B 47 n Name Format Range Description Notes Default Reference Example 1B 4An Name Format Range Description TPL 80 82 5 3 44 3 PRINTER FUNCTIONS Send n k in ascending order and place a 0 NUL code at the end When n kis less than or equal to the preceding value n k 1 the setting is complete and the data which follows is processed as normal data 1D 44 00 cancels all horizontal tab positions The previously specified horizontal tab position does not change even if the character width is modified Default tab positions are set at intervals of 8 characters columns 9 17 25 for FontA when the right side character spacing is O 09 Turn emphasized mode on off ASCII ESC E n Hex 1B 45 n Decimal 27 69 n 0 lt lt 255 Turns emphasized mode on off When the LSB of n is 0 the emphasized mode is off When the LSB of n is 1 the emphasized mode is on e Only the LSB of n is effective 1B 21 also turns on
95. x Decimal Function 0 Off 00 0 Cutter ok On 01 1 Cutter error 1 RESERVED 2 RESERVED 3 Off 00 0 EEPROM ok On 08 8 EEPROM error 4 RESERVED 5 RESERVED 6 RESERVED 7 RESERVED Cancel current line transmitted ASCII CAN Hex 18 Decimal 24 Deletes current line transmitted TPL 80 82 5 3 36 CUSTOM 3 PRINTER FUNCTIONS Notes Sets the print position to the beginning of the line Default Reference Example 1B 20 n Name Set right side character spacing Format ASCII ESC SP n Hex 1B 20 n Decimal 27 32 n Range lt lt 255 Description Sets the character spacing for the right side of the character to n x horizontal or vertical motion units Notes The right character spacing for double width mode is twice the normal value When the characters are enlarged the right side character spacing is m 2 or 4 times the normal value The horizontal and vertical motion units are specified by 1D 50 Changing the horizontal or vertical motion units does not affect the current right side spacing The 1D 50 command can change the horizontal and vertical motion unit However the value cannot be less than the minimum horizontal movement amount In standard mode the horizontal motion unit is used The maximum right side spacing is 255 200 inches Default n 0 Reference 1D 50 Exampl
96. y is enabled when it is pressed the printer advances the paper the number of increments programmed in the Eeprom If the FORM FEED key is not enabled and the printer is in Custom Emulation mode when the key is pressed the code 12 HEX is transmitted on the RS232 serial line This function may be modified by the ESC software command see section on software commands CUSTOM 3 TPL 80 82 5 INTRODUCTION e During power up if both keys are held down the printer enters the print setup routine Following the print out of the setup report the printer remains in standby until a key is pressed or signals arrive from the serial port each 10 characters it prints out hexadecimal and ASCII codes if the characters are underlined the receive buffer is full see Receive buffer hexidecimal print out e The Power On LED green indicates that the printer is on The Paper Low LED red indicates that the paper is about to run out e The Status LED yellow indicates printer status the check is made on line Given in the table below are the various LED signals and the corresponding printer status Tab 1 LED status Description Steady Printer ON no malfunction Rapid blinking Overheating Slow blinking lit for extended period No Paper message Slow blinking lit for short period Head turned upwards Remains off Printer malfunction TPL 80 82 5 4 CUSTOM 1 INSTALLATION AND USE 1 1 CONNEC

TPL 80 / 82.5 Ticket Printer

Contents

Download Pdf Manuals

Related Search

Related Contents