User Guide - Performance Audio
Contents
1. no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The Fusion FX Bar 5 is a seven channel DMX unit The DMX address is set on the rear panel of the Fusion FX Bar 5 Your unit and your DMX controller require a approved DMX 512 110 Ohm Data cable for data input and data output We recommend Accu Cable DMX cables If you are making your own cables be sure to use stan dard 110 120 Ohm shielded cable This cable may be purchased at almost all professional sound and lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split a Figure 1 American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 8 Fusion FX Bar 5 Set Up Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR XLR Male Socket XLR Female Socket 1 Ground F 2 Cold Figure 3 Figure 2 XLR Pin Configuration 1 2 Cold I 1 Ground i Pin 1 Ground 1 s i Pin 2 Data Compliment negative 1 1 Pin 3 Data True2. 3R levels Many of the individual beams are potentially hazardous to the eyes Do not that because the laser light is moving it is safe This is not true Nor do the laser beams always move Since eye injuries can occur instantly it is critical to prevent even the smallest possibility of any direct eye exposure In the laser safety regulation it is not legal to aim Class 3R lasers in areas which people can get exposed This is true even if it is aimed below people s faces such as on a dance floor Do not operate the laser without first reading and understanding all safety and technical data in this manual Always set up and install all laser effects so that all laser light is at least 3 meters 9 8 feet above the floor on which people can stand After setting up and before public use test laser to ensure proper American DJ www americandj com Fusion FX Bar 5 Instruction Manual Page 5 Fusion FX Bar 5 function Do not use if any defect is detected Do not use if laser emits only one or two laser beams rather than dozens hundreds as this could indicate damage to the diffraction grating optic and could allow emission of higher laser levels above Class 3R Laser Warnings amp Safety Do not point lasers at people or animals Never look into the laser aperture or laser beams Do not point lasers in areas in which people can potentially get exposed such as uncontrolled balconies etc Do not point lasers at highly re
3. has been removed located the fuse holder located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder has built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse Fusion FX Bar 5 Cleaning Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses must be carried out periodically to optimize light output 1 Use a soft cloth to wipe down the outside casing Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew Fusion FX Bar 5 Trouble Shooting Listed below are a few common problems the user may encounter with solutions Unit not responding to DMX 1 Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on some other DMX devices pin 2 may be hot Also check that all cables are connected to the right connectors it does matter which way the inputs and outputs are connected Unit does not respond to sound 1 Quiet or high pitched sounds will not activate the unit If problems are not resolved Contact American DJ for service 1 800 322 6337 American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 19 Fusion FX Bar 5 MANUFACTURER S LIMITED WARRANTY A American DJ Inc hereby warrants to the origin
4. limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall American Du Inc be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS All American Audio Products 1 year 865 day Limited Warranty except V Plus Series Ampli fiers All American Audio V Plus Series Amplifiers 3 year 1095 day Limited Warranty American DJ Lighting and American DJ Branded Products 1 year 365 day Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding Laser Products lamps and Star Tec Series American DJ Laser Products and Star Tec Products 90 Day Limited Warranty American DJ L E D Products 2 year 730 day Limited Warranty excluding motors which have a 1 year 365 day Limited Warranty
5. positive Passe sssesssesses5 Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems O and interference It is always advisable Z P to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion Conductor 3 Pin XLR Female Out 5 Pin XLR Male In Ground Shield Pin 1 Pin 1 Data Compliment signal Pin 2 Pin 2 Data True signal Pin3 Pin 3 Not Used Do Not Use Not Used Do Not Use American DJ Supply www americandj com Fusion FX Bar 5 In
6. American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 20 Fusion FX Bar 5 Notes Fusion FX Bar 5 Notes American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 21 American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 22 Fusion FX Bar 5 Specifications Model Fusion FX Bar 5 Voltage 100V 240V 50 60Hz Power Cord Daisy Chain 10 Fixtures Max LEDs 90 x 5mm White LEDs 1 TRI Color LED Laser 30mW Green Laser 80mW Red Laser Power Consumption 32W Fuse 7Amp Power Cord Daisy Chain 10 Fixtures Max Weight 11lbs 4 7Kgs Dimensions w Bracket 21 5 L x 7 W x 5 75 H 542 x 178 x 143mm Colors RGB amp W DMX Channels 7 DMX Channels Working Position Any safe working position Warranty 2 Years 730 days LEDs 90 Days Laser Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 23 American DJ Supply American DJ World Headquarters 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 582 2610 Web www americandj com E mail info americandj com American D
7. J Europe Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu www americandj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On FTE facebook com americandj twitter com americandj youtube com adjlighting
8. Rev 3 14 User Instructions Fusion FX Bar 5 Introduction Unpacking Thank you for purchasing the Fusion FX Bar 5 by Ameri can DJe Every Fusion FX Bar 5 has been thoroughly tested and has been shipped in perfect operating condition Carefully check the ship ping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are miss ing please contact our toll free customer support number for further instructions Do not return this unit to your dealer without first contact ing customer support Introduction The Fusion FX Bar 5 is part of American DJ s continu ing pursuit for creating high quality affordable intelligent fixtures The Fusion FX Bar 5 is a DMX intelligent LED wash amp laser fixture The unit has 3 operating modes Sound Active with adjustable sound sensitiv ity Show Mode or DMX Control This unit can be used as a stand alone fixture or in a Master Slave configuration Customer Support American DJe provides a toll free customer sup port line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www americandj com for any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pa
9. X Bar 5 Instruction Manual Page 7 Fusion FX Bar 5 Set Up Power Supply The American DJe Fusion FX Bar 5 contains a auto matic voltage switch which will auto sense the voltage when it is plugged into the power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compli ant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit
10. al purchaser American DJ and American Audio products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by ac ceptable evidence at the time service is sought Warranty B For warranty service you must obtain a Return Authorization number RA before sending back the product Contact American Du Inc Service Department at 800 322 6337 Send the product only to the American Du Inc factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty American Du Inc will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product American Du Inc shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof G This warranty is void if the serial number has been altered or removed if the product is modified in any manner which American DJ Inc concludes after inspection affects the reliability
11. and then press and hold the MENU button for at least three seconds to confirm and lock the change into the system memory If the MENU button is not pressed and held within eight seconds the fixture will automatically confirm and lock the change into the system memory To exit without making any changes press the MENU button MZ M Ht OR DMX Address Setting via control board 1 Press the MENU button until ADDR ENTER 2 X will now be displayed X represents the displayed address Press the UP or DOWN buttons to find your desired address 3 Press ENTER to confirm then connect your DMX controller NOTE lf after you connect your DMX controller the unit does not fall into DMX mode press and hold the MENU button for at least 3 seconds is displayed press DINN os SLN This will let you set unit as a slave in a master slave configuration 1 Press the MENU button until SLND is displayed press ENTER Either Si P or Si 2 will be displayed 2 Press the UP or DOWN buttons until your desired setting is displayed press ENTER to confim NOTE In a Master Slave configuration you can make one fixture the Master and then set the next fixture to SL 2 the American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 11 Fusion FX Bar 5 fixtures will now have contrast movement to each other System Menu D E LuU a Li oy SH 5 Show modes 0 16 Factory prog
12. ate this unit when it s cover is removed e Never plug this unit in to a dimmer pack e Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged e This unit is intended for indoor use only use of this product out doors voids all warranties e During long periods of non use disconnect the unit s main power e Always mount this unit in safe and stable matter e Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 19 for cleaning details e Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances inclu ding amplifiers that produce heat The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 4 Fusion FX Bar 5 Laser Warnings am
13. cific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail support americandj com To purchase parts online visit http parts americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact American DJe PLEASE recycle the shipping carton when ever possible American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 2 Fusion FX Bar 5 General Instructions To optimize the performance of this product please read these operat ing instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference CAUTION IMPORTANT When installing this projector make sure that it is mounted in a manner that prevents the audience from looking directly into the beam and the beam from striking the audience Fusion FX Bar 5 Features e White LED Wash Strobe Effect 1 TRI Color LED Moonflower amp 1 Green Laser Strobing e Built in Microphone e DMX 512 protocol Seven DMX Modes 16 Show Modes 1 Radom Show Mode 3 Operating Modes Sound Activ
14. e Show Mode or DMX Control Sound Sensitivity Adjustable e UC3 Remote Control Compatiable Not Included e Power Cord Daisy Chaining See page 16 Fusion FX Bar 5 Warranty Registration The Fusion FX Bar 5 carries a 2 year 730 days limited warranty for LEDs and a 90 Day limited warranty for the laser Please fill out the enclosed warranty card to validate your purchase and warranty You may also register your product online at www americandj com All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of pur chase invoice Please contact American DJ customer support for a R A number American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 3 Fusion FX Bar 5 Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside e Never oper
15. eat of the music 1 Press the MENU button until SOUN is displayed and press ENTER 2 Press the UP or DOWN buttons until ON is displayed and press ENTER and then press and hold the MENU button to confirm 3 To adjust the sound sensitivity press the MENU button until SENS is displayed Use the UP or DOWN buttons to adjust sen sitivity See page 12 for more info 4 The optional UC3 Controller not included may be used to con trol different functions including blackout See page 18 for UC3 controls and functions Show Mode This mode allows a single unit or several units linked together to run your desired factory show 1 Press the MENU button until SAND is displayed and press ENTER 2 Press the UP or DOWN buttons until you find your desired show press ENTER then press and hold the MENU button to confirm 3 The optional UC3 Controller not included may be used to con trol different functions including blackout See page 18 for UC3 controls and functions Fusion FX Bar 5 With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 10 fixtures maximum After 10 fixtures you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures Power Cord Daisy Chain American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 16 Fusion FX Bar 5 DMX Channe
16. flective surfaces such as windows mirrors and shiny metal Even laser reflections can be hazardous Never point a laser at aircraft this is a federal offense Never point un terminated laser beams into the sky Do not expose the output optic aperture to cleaning chemicals Do not use laser if the laser appears to be emitting only one or two beams Do not use the laser if the housing is damaged the housing is open or if the optics appear damaged in any way Never open the laser housing The high laser power levels inside of the protective housing can start fires burn skin and will cause instant eye injury Never leave this device running unattended The operation of a class 3R laser show is only allowed if the show is controlled by a skilled and well trained operator familiar with the data included in this manual The legal requirements for using laser entertainment products vary from country to country The user is responsible for the legal require ments at the location country of use Always use proper lighting safety cables when hanging lights and effects overhead American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 6 Fusion FX Bar 5 Laser Warning Labels 40mm 40mm American DJ Supply CA 90040 USA DJ Supply inc 6122 S Eastern Ave American Specification stickers wwz ingal 41mm www americandj com Fusion F
17. ing time of the fixture will now be displayed Press MENU to exit ER This will display the software version 1 Press the MENU button until VER is displayed Press the ENTER button and the software vesion will be displayed 2 Press the MENU button to leave this function American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 14 Fusion FX Bar 5 Operation CAUTION IMPORTANT When installing this projector make sure that it is mounted in a manner that prevents the audience from looking directly into the beam and the beam from striking the audience Universal DMX Control This function allows you to use a Elatione universal DMX 512 controller to control the chases and patterns dim mer and strobe A DMX controller allows you to create unique pro grams tailored to your individual needs 1 The Fusion FX Bar 5 is a 7 DMX channel unit See pages 17 18 for a detailed description of the DMX traits 2 To control your fixture in DMX mode follow the set up procedures on pages 8 9 as well as the set up specifications that are included with your DMX controller Use the controller s faders to control the various DMX fixture traits This will allow you to create your own programs Follow the instructions on page 11 to set the DMX address then connect your DMX Controller 6 For longer cable runs more than a 100 feet use a terminator on the last fixture 7 For help operating in DMX mode consult the ma
18. ls amp Functions Fusion FX Bar 5 DMX Values and Functions Function Function WHITE DIMMER STROBE 5 RED LASER 0 7 OFF 0 127 LASER OFF 8 190 MASTER DIMMER 0 100 128 255 LASER ON 191 200 SOUND ACTIVE GENAST 201 247 STROBING SLOW FAST 0 127 LASER FF 248 255 FULL ON Jod a255 ARON MOON FLOWER DIMMER STROBE 7 N gee OFF 0 9 NO ROTATION 8 190 MASTER DIMMER 0 100 10 120 CLOCKWISE ROTATION FAST SLOW 191 200 SOUND ACTIVE 404 134 NOROTATION an eer STROBING SLOW FAST 135 245 COUNTER CLOCKWISE ROTATION 248 255 FULL ON SLOW FAST MOON FLOWER COLOR 246 255 NO ROTATION 0 18 RED 19 36 RED amp GREEN 37 54 GREEN Fusion FX Bar 5 UC3 Control 55 73 GREEN amp BLUE 74 91 BLUE Stand By Blackout the unit 92 109 RED amp BLUE 110 127 RED GREEN amp BLUE unction 1 White LED strobe Select Shows 128 159 RED GREEN unction 160 191 GREEN BLUE 2 Moonflower Strobe 1 16 192 223 RED BLUE 224 255 RED GREEN BLUE Mode Sound LED OFF Speed LED ON MOON FLOWER ROTATION 0 9 NO ROTATION 10 120 CLOCKWISE ROTATION FAST SLOW 121 134 NO ROTATION 135 245 COUNTER CLOCKWISE ROTATION SLOW FAST 246 255 NO ROTATION American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 17 American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 18 Fusion FX Bar 5 Fuse Replacement Locate and remove the unit s power cord Once the cord
19. nual included with your DMX controller ae 2 Master Slave Operation This function will allow you to link up to 16 units together and operate without a controller In Master Slave opera tion one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Using appropriate XLR cables daisy chain your units together via the XLR connector on the rear of the units Remember the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a terminator at the last fixture 2 On the Master unit find your desired show or choose sound act tive mode 3 On the slave units tap the MENU button until SLND is display ed and Press ENTER Use the UP or DOWN buttons to switch American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 15 Fusion FX Bar 5 between either SL1 or SL2 Once you have made your choice press ENTER Please see page 11 for more info 4 The slave units will now follow the Master unit 5 The optional UC3 Controller not included may be used to con trol different functions including blackout Operation Sound Active Mode This mode allows a single unit or several units linked together to run to the b
20. of the product if the product has been repaired or serviced by anyone other than the American DJ Inc factory unless prior written authorization was issued to purchaser by American DJ Inc if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintenance cleaning or periodic check up During the period specified above American DJ Inc will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of Ameri can DJ Inc under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of American DJ All products covered by this warranty were manufactured after January 1 1990 and bear identifying marks to that effect E American DJ Inc reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore man ufactured No warranty whether expressed or implied is given or made with respect to any acces sory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by American DJ Inc in connection with this product including warranties of merchantability or fitness are
21. p Safety NON INTERLOCKED HOUSING WARNING The Fusion FX Bar 5 contains high power laser devices internally Do not open the laser housing due to the potential exposure to unsafe levels of laser radiation The laser power levels if the unit is opened can cause instant blindness skin burns and fires STOP AND READ ALL LASER SAFETY DATA OPERATION INSTRUCTIONS AND LASER SAFETY The light source emitted from this product can potentially cause eye injury if not set up and used properly The light source emitted from a laser is very different from any other light sources with which you may be aware of Laser light is thousands of times more concentrated than any light from any other kind of light source This concentration of light can cause instant eye injuries primarily by burning the retina the back of your eyeball contatining cells that are sensitive to light Even if you cannot feel heat from a laser beam it can still potentially injure or blind you or your audience Even very small amounts of laser beam light are potentially hazardous even at long distances Laser eye injuries can be sustained faster than you can blink Do not think that because this laser splits the laser beam into hun dreds of beams and that the laser beam is scanned out in high speed that an individual laser beam is safe for eye exposure This laser uses dozens of milliwatts of laser power Class 3B levels internally before it splits into multiple beams Class
22. rams 1 Show mide can run with or without sound active mode on With sound active mode on the shows will tend to run faster 1 Press the MENU button until SAND is displayed press ENTER 2 SH X will now be displayed X representing a number between 0 16 Shows 1 16 are preset shows while SH D is random show Press the UP or DOWN buttons to find your desired show 3 Press ENTER and then press and hold the MENU button for at least 3 seconds to confirm WW HIN UL I In this mode you can run in sound active mode 1 Press the MENU button until SUUN is displayed press ENTER 2 Either ON or OFF will now be displayed Press the UP or DOWN buttons to select one or the other 3 When you have made your selection press the ENTER and then press and hold the MENU button for at least 3 seconds to confirm SENS Sound sensitivity control 1 Press the MENU button until SENS is displayed press ENTER 2 The display will show a number between 0 100 Press the UP or DOWN buttons to adjust the sound sensitivity 0 being the least sensi tive and 100 the most sensitive 3 Press the ENTER and then press and hold the MENU button for at least 3 seconds to confirm American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 12 Fusion FX Bar 5 System Menu NL This will control blackout 1 Press the MENU button until BLNO is displayed p
23. ress ENTER 2 Either YES or NU will now be displayed Press the UP or DOWN buttons to select one or the other 3 Press ENTER and then press and hold the MENU button for at least three seconds to confirm LEL With this function the LED display will turn off after 2 minutes 1 Press the MENU button until LEU is displayed press ENTER 2 Either ON or GFF will now be displayed Press the UP or DOWN buttons to select UN to keep the LED display on at all times or OFF to allow the LED display to turn off after 2 min utes Press any button to turn on the LED display again 3 Press ENTER and then press and hold the MENU button for at least three seconds to confirm LOM This will flip the LED display 1 Press the MENU button until DSP is displayed press ENTER 2 Press ENTER to flip the display Press ENTER to flip it again Press MENU when you have decided on your desired display setup 1 This function will run a self test program 1 Press the MENU button until TEST is displayed press ENTER American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 13 Fusion FX Bar 5 2 The fixture will now run a self test Press the MENU button to exit System Menu FHRS With this function you can display the running time of the unit 1 Press the MENU button until FARS is displayed press ENTER 2 The runn
24. struction Manual Page 9 Fusion FX Bar 5 System Menu J Addr E a DMX512 Address Setting l l vA GL Slave Mode Normal SLi 1 3 SL 2 Slave mode 2 Light Show 5h O T i Shad ab ShowMode Sh 16 cnn an Sound Mode on So BES offl Sound Mode off m _ m MENU SPASH _ Sound Sensitivity IDD Burd 42S Blackout Mode Yes Blackout na Blackout Mode No Blackout iz LEDon Lt Og an wes OFF LEDoff JISP dior Normal dG P Inversion EEO Self test FHS Fixture Hours ufr S oftware Version American DJ Supply www americandj com Fusion FX Bar 5 Instruction Manual Page 10 Fusion FX Bar 5 System Menu On Board System Menu The Fusion FX Bar 5 comes with an easy to navigate system menu This next section will detail the functions of each command in the system menu Please read the next section thoroughly To access the main menu press the MENU button Tap the UP or DOWN buttons until you reach function you wish to change When you reach the function you wish to change press the ENTER button When a function is selected use the UP or DOWN buttons to change the func tion settings Once your changes are made press the ENTER button
Download Pdf Manuals
Related Search