Use Manual - Hosen lighting technology limited Since 2003, Welcome!
Contents
1. Product Introduction 1 1 Product Feature gt 4kinds of running mode mM External control mode Slave mode DMX 512 controller control 2 kinds channel modes Master salve model control auto match the signal from controller and the Master light no need to set by menu E Auto run mode Master mode Different kind of Gradual change amp Random change Different kind of Strobe speed change strobe slow to fast mixing strobe Strobe basic color Strobe Gradual change E static mode Master mode Itcan fix any color without the controller also work this color with strobe E Sound mode Master mode Included 2 kinds of commonly used sound mode gt Software cutting E The light would be turn off when the dimmer channel is 0 procedure would keep working E The difference with BLACKOUT key controller keys amp Software cutting only work this light and do not clear up the controller data gt No liner dimmer amp liner dimmer E The Effect get high praise from the professional technologist gt Screen Protect E It will enter blank screen without any operate on the keyboard in 30 seconds Press any keys then it can quit screen protection gt Temperature Protection E Itcan be set to temperature protection mode gt Speed of the Fan E The fan will start to work when the working temperature reach 40 degree and the speed will be changed according to the change of temperature gt Can support reverse di2. and safety warning described in this user manual 3 Manufacture will not with responsibility for those operation not according to this instruction Operation attentions 1 Do not connect power cable of other electric products with this unit 2 Do not connect DMX512 signal cable of other electric products with this unit 3 Check the fixture and power cord time to time make sure the power cord is not crimped or damaged by sharp edges 4 Do not shake the fixture Avoid brute force when installing or operating do not permit operation by person not qualified for operating the device 5 Always make sure that the products are connected the proper voltage and that the line voltage of the products connecting to is not higher than that stated on the decal or rear panel of the fixture 6 During long period of non use disconnect the unit s main power 7 Do not attempt to operate this unit if the power has been frayed or broken If the exterior cord of the fixture is damaged it must be replaced by manufactory agent or qualified technician 8 There are no serviceable parts inside the unit Do not open the housing or attempt any repairs yourself 9 Maximum ambient temperature Ta is 35 C Do not operate unit at temperature higher than this 10 The surface temperature of the light can reach to 65 C cool down at least 15 minutes before the light operated 11 Avoid looking into the source directly especially those who suffer from epileptic fit
3. be controlled in single and also be controller in many units 2 Overview 169mm_ 643mm Hosen lighting Technology Limited 3 Photographic Chart Red Led Lux F200 1450650 300 200 140 Geen Led Luk JODO 1450670 Bhie Led Loe White Led Lux Full Led Lum Caistancel m Diameter m Of 046 092 1 39145 231 277 3 23 369416 462 Red Led Lux Green bed Lin 4000 Ste Blue Led Lux 3350 720 White Led Lux 3250 Ful Led Lur Sm 3m Im Im 3m Sm Distancelm Diameter m Hosen lighting Technology Limited Installation 1 Installation When installation keep the device for away the heat sensitive objects and explosives sensitive objects leave at least 50CM of free space around the device When the device put on horizontal place the device must be placed directly on the place and device must be secures with a mounting holder When rigging the device on the truss and the head face to the floor the screw one clamp each via a M12 screw and nut onto the mounting holder Insert the quick lock fasteners of the first mounting holder into the respective holder on the bottom of the device Tighten the quick lock fasteners fully clockwise Install the second mounting holder And the safety rope must be used at same time Hosen lighting Technology Limited Please use qualified safety rope which can hold at least 10 times the weight of the fixture You must only use safety ropes wi
4. it s the vice menu it will back to main menu eee Key of ENTER Press it and can save the data Stag 0 20 If it s the main menu and it have vice menu it will enter the vice menu LEP 0 If it s the vice menu it will exchange to the next vice menu gt AREER 40 120 Key of UP DOWN od SP It s no function if the menu not include the decimal point If the menu include the decimal point it can set the data after cESt the decimal point And it need press ENTER to save the data Hosen lighting Technology Limited 2 2 Menu Menu State Operation Remark Main menu Vice menu No menu A advance UP DOW adjust ID address disconnect the N controller and External control ENTER Save ID address connect the master mode light then it will standard channel follow the master model light No vice menu d dmx UP DOW Adjust ID address It will flicker when N no signal External control ENTER Save ID address mode basic channel model UP DOW choose the program N SP speed UP DOW adjust speed N choose the auto run ENTER save the data ae a e No menu Sod sound UP DOW change to sound eee n G b Wats UP DOW change the color SON TE a set the color ENTER save the data change to vice N St strobe UP DOW change the strobe eee the strobe and its ENTER save and exchange oe er have 2 vice tEMp temperature ENTER menus temperature control function a cur
5. Hosen lighting Technology Limited Led Profile Spot light 200W 2in1 cool warm white amber HS PS20021 Use Manual Instruction Hosen lighting Technology Limited OVERVIEW Thank you for using our product this unit is designed for indoor using it s widely used for stage building disco etc as high power led effects lighting this unit can be operated as a single unit or multipe units for large applications Direct input of DMX512 signal to unit to allow it controlled by any DMX controller powerful internal programs and friendly and convenient operation interface allows customers to program freely to any different lighting project requirements for installation or showing This high power par can has gotten the nice sculpt efficient save electricity and durable This product complies with the following standards EN61000 3 2 2006 A2 2009 EN60598 1 2008 A1 1 2009 Technical Parameter e Input voltage AC110V 240V 50 60Hz e Power consumption 260W e Lamp Cool Warm white 200W super brightness Module LED e Control Mode DMX512 Master Slave Sound active Auto run e DMX channel 2 5CH e Beam Angel 19 26 36 e Housing Die casting Aluminum e Color temperature 2000k 6500k e Fan Noise 12 1 20dB e Fan speed 900 2 000RPM 10 e Fan life 30000 hours e Refresh rate 4000HZ flick free for TV and Studio e IP Grade IP20 e N W 6 kgs e G W 8kgs e Dimensions 660x285x295mm Hosen lighting Technology Limited 1
6. rent temperature ENTER Hosen lighting Technology Limited t top UP DOW Change the temperature protection data set the temperature ENTER save and m protect ssi No vice menu diSP display ENTER reverse set to reverse No vice menu reSt reset ENTER enter a interface The password is of key UP DONW UP DOWN return Initial State 2 3 Channel data 2 3 1 Standard channel model fe fess dimmer O a toss fo O s fos foo O S this channel control the speed when running 11 255 the speed of strobe 255 is the the build in program ma fastest 5 0 20 speed of dimmer 4 the slowest and aana speed of dimmer 2 61 80 speed of dimmer 1 81 99 speed of dimmer off fastest and no any delay OO F i ee 190 199 ime progami0 200 240 change cotor vy sound cont 241 255 tobe by sound contol o Hosen lighting Technology Limited 2 3 2 Basic channel model 0 255 color 1 1 Description of the Device 1 Profile With the idea of energy saving and environment projection the device use lower power loss and extremely high efficiency led The device housing cover is made of used the new high strength heat resistance engineering plastics with the IEC standard The device is suitable in the large scale theatrical performance the performance hall the bar night club and so on The product conforms to the international standard DMS512 agreement completely the device can
7. s 12 Do not install the fixture on combustible surface Away mount this unit in safe and stable mater DISCLAIMER 1 The device is with one year warranty The warranty period appear non artificial quality problem this company is responsible for free maintenance 2 User violate operation caused the machine failure this is user responsibility 3 If due to the wrong operation or intense impact caused product destroy even safety accidents the manufacturer does not undertake any responsibility 4 Prohibit replaced product components by any person therefore caused any consequences will be whose responsible
8. splay Hosen lighting Technology Limited 1 2 Multi light working in the same time When using controller to control multi lights to work in strobe the controller just send the channel data The strobe effect will be depend on each light itself And please take attention for the follow situation 1 There will be many situations make the lights are not synchronization in the beginning For example the different time of opening the light or different time of them connect to the controller In this case you can change value of the controller for example push 20 to 0 and back to 20 then it can be synchronization 2 Due to crystal frequency of different lights are not the same exactly soit may not be synchronization after long time 3 If need to keep synchronization for long time there are two ways to do so A Using the controller to edit program make the strobe auto run effect then they must be synchronization B Using the Maser Slave model 2 Operation 2 1 Key operation PE 1 512 ae The first list is the main menu press MENU to exchange the 3000 1 54 2 second list is vice menu press ENTER to get in or exchange If the menu include the decimal point that s the data and can RED 1 0 be set by the Key of Up Donw HA 1 20 Key operation Sod 1 e Key of MENU Press it and can save the data If it s the main menu it will exchange to next main menu SERE r c55 Q 255 If
9. th quick links with screw cap Pull the safety rope trough the hole on the bottom of the base and over the trussing system etc Insert the end in the quick link and tighten the fixation screw A safety rope which already hold the strain of the crash or which is defective must not be used again 2 DMX512 Connection Please use xlr xlr wires connect the DMX output of the controller with the DMX input of the first device and connect the DMX output of the first device with the DMX input of the second device always connect one output with the input of the next device until all device are connected DMX OUT DMX IN Please use qualified xlr xlr dmx cables Hosen lighting Technology Limited 3 Connection with mains The person involved with the power connection must be qualified And has the electrical engineering certificate Connect the device to the mains with the power plug The earth has to be connected Power consumption 260w input power supply AC 100V 240v 50 60Hz 4 The use of gobo frame Take out the gobo frame loose the screws insert the gobos and lock the screws again Insert the gobo in the slot When you exchange the gobo please insert it after unscrew the screw of teh gobo then tighten the screw again Put the gobo in the slot shown in the c Picture The gobo support Hosen lighting Technology Limited 5 Use iris Iris is not included when the projec
10. tor leave factory user can purchase the iris if needed Loose the screw and insert the iris 1 Unscrew the screws of the plastic card move the card till the slot revealed completely 2 Insert iris in the slot 6 Replacing fuse Before replace the fuse unplug mains lead Procedure Step 1 Unscrew the fuse holder on the rearpanel with a fitting screwdriver from the housing anti clockwise Step 2 Remove the old fuse from the fuse holder Step 3 Install the new fuse in the fuse holder Step 4 Replace the fuse holder in the housing and fix it 7 Focus The objective lens cylinder is usually shrinked before leaving factory after connect the projector to the mains user may loose the screws and pull out the lens cylinder till the white light output circular is clearly presented locking tightly the two screws again When the projection distance is changed user can follow previous operation steps and focus the projector Unscrew the screws of the lens move the lens re in perfect position tighten the screws of the lensagain Hosen lighting Technology Limited SAFETY INSTRUCTIONS When use this product please pay close attention to the following items 1 The product must be installed by a qualified professional 2 The product left the place of manufacture in perfect condition In order to maintain this condition and for safe operation the user must always follow the instructions
Download Pdf Manuals
Related Search