- Eliptix
Contents
1. ClockWatch User Manual interspace _ industries Cueing and Presentation Control Specialists Contents Introduction Environmental Electrical Compliance Safety Instructions Diagrams Regulations Compliance Operating Instructions Programming Technical Support Contact Introduction ClockWatch combines clear traffic light type signalling with a simple to use timekeeping system The intuitive control module has been designed especially for non technical users so that formal timekeeping can be easily managed in a wide variety of applications Signalling to speakers to ensure everything runs to time is the key to a smooth professional meeting and ClockWatch silently prompts presenters when to speak green light when to summarise amber light and when to finish red light Feed back to a timekeeper and or the meeting chairperson can also be provided via a variety of visual or numeric displays Designed for reliability and versatility ClockWatch is based on AV industry proven rugged design uses readily available 3pin XLR mic cable connectors and the system can be set up in just 1 2 minutes or be permanently installed if required Meeting Control Made Easy We hope ClockWatch exceeds your expectations and welcome any feedback that you have about this or any of our products Thank you The Interspace Industries Team www interspaceind com Environmental WEEE and RoHS Compliance ClockWatch and its2. associated accessories have been manufactured and sold in accordance with the requirements of the EC WEEE and RoHS directives Please return all end of life items to your supplier or Interspace Industries directly for appropriate disposal Packaging Materials Cardboard box Grade 150 K T B Single Walled Corrugated Brown Kraft Protective Foam Grade HLB 22 Grey Foam High Load Bearing Electrical CE Mark ClockWatch and its associated accessories have been designed manufactured and certified to comply with all requirements ofthe European CE standard Safety Instructions All safety and operating instructions should be read before this product is operated and should be retained for further reference Please adhere to all the warnings on this product and in these operating instructions Please follow these instructions carefully Power Only use the power source indicated on the device Devices equipped with a grounded plug should only be used with a grounded type outlet In no way should this grounding be disconnected modified or suppressed Power Supply Lead To unplug the device always pull by the plug itself not the power supply lead The power source outlet should always be near the MicroCue main unit and easily accessible Ensure the power supply lead cannot be walked on or damaged by items placed on or against it Do not use if the power supply lead is damaged Using the device with a damaged power supply lead may expose y
3. button 3 The system then stores the new sequence and resets This new sequence will now run each time the PRESET button that was chosen in 1 above is pressed For Technical Support or Sales Enquiries Interspace Industries Head Office 44 0 870 770 8088 Emergency Technical Support Hot Line 44 0 7976 385046 Website www interspaceind com interspace _ industries 28 High Street Arlesey Bedfordshire SG15 6RA UK Tel 44 0 870 770 8088 Fax 44 0 870 770 8089 Email moreinfo interspaceind com www interspaceind com
4. ce is running any of the LightTower lamp control buttons KD O Or can be pressed This immediately illuminates whichever lamp has been selected and cancels the timer sequence Programming Preset Timing Sequences 1 After resetting ClockWatch by briefly pressing the RESET button press and hold the RESET button together with whichever one of the preset time sequence buttons that you wish to program Hold both buttons down for around 5 seconds When the preset button glows brighter ClockWatch is now in programming mode and you can release both buttons When programming a new timing sequence the system assumes the LightTower is always going to start from Green when the timing sequence commences To program the time interval until the LightTower turns from Green to Amber pressing the PAUSE button amp increases the time interval by 5 seconds To decrease the time interval press the PAUSE button while holding down the RESET button 9 The numeric display updates with each press of the PAUSE button you can see the time interval you are programming When the required interval has been programmed release all buttons then momentarily press the AMBER button O The system is now ready to program the time interval until the LightTower changes from Amber to Red To program the time interval until the LightTower changes from Amber to Red repeat step 2 above When the required interval has been programmed momentarily press the RED
5. he source Quick Start Operation Manual Mode By simply pressing any of the LightTower lamp control buttons Q or the corresponding lamp on the LightTower and or visual displays will illuniMate atcordingty The selected lamp will remain illuminated until either the same button is pressed again this extinguishes the lamp or an alternative coloured lamp is pressed It is not possible to have more than one coloured lamp illuminated By pressing the PAUSE button Q any of the LightTower lamps are illuminated the lamp will flash intermittently thus Signalling that the time keeping has been paused Pressing the PAUSE O will stop the lamp from flashing Quick Start Operation Auto Mode Refer to Programming section overleaf for instruc tions on how to pre program the preset time sequence buttons By pressing either of the preset time sequence buttons A the pre programmed timer sequence starts immedi ately and the LightTower m urs according to the pre programmed timing profile At any time during the timer sequence the PAUSE button Q can be pressed to pause the sequence While paused the LightTower lamp will flash intermittently to signal that the se quence has been paused To resume the timing sequence press the PAUSI pp tton again 6 Should it be necessary to cancel a timing sequence simple press the RESET button This extinguishes all displays and resets the timer display O At any time while a preset timing sequen
6. ou to electric shock or other hazards Check the condition of the power supply lead regularly Contact your dealer or service centre immediately for a replacement if damaged Keep Away From Harmful Substances To prevent the risk of electric shock and fire do not expose this device to rain humidity or intense heat sources such as radiators or direct sunlight Avoid using this equipment in environments where there is excessive heat dust moisture chemicals vibration or mechanical shocks Slots and Openings These are designed into the device for ventilation and to avoid overheating Always ensure these openings remain clear Do not attempt to insert anything into these openings under any circumstances If liquids have been spilled on or objects have fallen into the product it must be checked by a qualified technician before re using Connections All inputs and outputs except for power input are TBTS defined under EN60950 eo DO NOT OPEN SYSTEM DUE TO HIGH VOLTAGE DO NOT IMMERSE IN WATER If you have any queries regarding these safety instructions or how to maintain the unit please do not hesitate to contact us on 44 0 870 770 8088 Servicing Do not attempt to service this product yourself Opening or removing covers and screws may expose you to electric shocks or other hazards Refer all servicing to qualified service personnel Diagrams Figure 1 ClockWatch Connections Diagram Iter Lamga A Light T
7. ower labi Larga A Muse Dalas O HA LISA Mun On On apum Clock Watch j meri pace laua ry A We iera ponad com RoHs Figure 2 ClockWatch Front and Rear Panel Controls 5 DECLARATION OF CONFORMITY We declare under our sole responsibility that the product ClockWatch To which this declaration relates is in conformity with the following standards or other norma tive documents EN55103 1 amp EN55103 2 1966 Specific for professional Audio Visual Products Used in environment as defined under E2 Commercial and Light industry example Theatres EN60950 1 2000 Following the provisions ofthe EEC Directive 89 336 EEC and 73 23 EEC pro kg Dave Humphrys F Managing Director Interspace Industries Ltd Issued on Date 14 May 2008 Operating Instructions Unpacking and Connections Unpack the main unit and place on a flat surface within easy access for the Operator Adjust the angle of the main unit by loosening the bracket securing fasteners on each side of the main unit and re tightening once the most comfortable angle is achieved Position the LightTower and any other display units for best viewing and connect the Light Tower s to connections amp and any numeric or intelligent lamps to connections 8 ga on the rear panel 9 Q unit using 3 pin XLR mic cables see figures M maxtnum combined cable distances can be as much as 100m 300ft Connect the IEC power cable to ClockWatch and switch on the power at t
Download Pdf Manuals
Related Search