adaptat on nstruct ons SM6-36
Contents
1. mu he lt lt replacing a resistor 11 S1B22867 revision 01 disassembling the resistor and reassembling the new resistor For DM1 A DM1 D DM1 W IM and SM cubicles For the other cubicles except DM1 A DM1 D DM1 W IM and SM cubicles S1B22867 revision 01 Schneider Electric service centers are there for engineering and technical assistance start up training preventive and corrective maintenance adaptation work spare parts Call your sales representative who will put you in touch with your nearest Schneider Electric service centre Schneider Electric Industries SAS 89 boulevard Franklin Roosevelt F 92500 Malmaison France Tel 33 0 1 41 29 85 00 http www schneider electric com S1B22867 revision 01 As standards specifications and designs change from time to time please ask for confirmation of the information given in this publication Conception r daction Service Documentation Technique T amp D Edition 04 07 20112. SM6 36 English distribution MT adaptation instructions heating resistors Scheider symbols and conventions S1B22867 revision 01 SCHNEIDER ELECTRIC foreword Caution you will find all the symbols below throughout the document indicating the hazard levels depending on the different types of situation as per iso 3864 2 U gt Z a m I DANGER failure to follow this instruction will result in death or serious injury as per 150 3864 2 gt WARNING failure to follow this instruction may result in death serious injury A CAUTION as per iso 3864 2 CAUTION failure to follow this instruction may result in injuries This alert signal can also be used to indicate practices that could damage the SM6 unit INFORMATION ADVICE We draw your attention to this specific point contact the Schneider Electric service unit for diagnosis and advice D Call your sales representative who will put you in contact with the closest SCHNEIDER ELECTRIC group service centre You can log on to www schneider electric com distribution rules A CAUTION The aim of this publication is to enable the SM6 unit to be installed correctly A CAUTION This document is not a commercial document It is a strictly technical document drawn up by Schneider Electric S1B22867 revision 01 safety rules S1B22867 revision 01 A CAUTION A
3. ables and housing C Connection pack preparation The operations allowing access to the various compartments and for reassembling the cubicle are described in the user manual field of application No restrictions access to the subset To reach the subset remove the following parts 1 front panel 2 low voltage compartment cover fixing parts 2 3 2 bolts 6 x 12 2 contact washers 5 heating resistor S1B22867 revision 01 heating resistor cabling electrical diagram For these cubicles electrical connection of heating resistor A is performed by means of a 220 V 50 Hz auxiliary supply S1B22867 revision 01 wiring feed through Pass the resistor wires from LV Compartment to operating mechanism compartment and through the hole in the frame and lower them inside the cable duct to the cable connection compartment Take off the resistor wires from cable duct and pass them into the cover and connect with heater 8 S1B22867 revision 01 procedure resistor S1B22867 revision 01 D DM1 assembling in DM1 A and DM1 W cubicles assembling in IM and SM cubicles Val LL s _ ee ee ae am m S1B22867 revision 01 10 En V O lt y v CN gt lt o assembling in CM CM2 DM2 GAM IMB gt E ca gt O O a IMC cubicles
4. ll the operations described below must be performed in compliance with applicable safety standards under the responsibility of a competent authority A WARNING The contractor must be certified and authorised to manipulate and perform work on the SM6 unit A CAUTION Only undertake the work after having read and understood all the explanations given in this document If you have any difficulty complying with these rules please contact Schneider Electric 4 S1B22867 revision 01 concerning this document safety requirements special tools kit contents For IM IMB IMC QM QMB SM TM GBC A GBC B GAM GAM2 CM CM2 DM2 cubicles use 51000107F For DM1 A DM1 D DM1 W DM2 W QMC cubicles use 51000107E S1B22867 revision 01 general This publication is intended strictly for use within Schneider Electric and is not a sales document lt contains instructions concerning the modification or the adaptation of assemblies The parts referred to form part of a kit and are not available separately This document may not be reproduced in any form or by any means and is reserved exclusively for use by Schneider Electric representatives The busbar compartment and cable connection compartment will be de energised The line disconnector will be in the earth position and the HVA cables de energised no A Terminal rail with terminal blocks and thermostat B Heating resistor with c
Download Pdf Manuals
Related Search