User`s Manual Advanced Wind/Solar Hybrid Controller - Solar
Contents
1. do not meet the description or can not return to normal please contact our service department or salesman to repair or replace s10 www neoenerji com2. solar curve wind energy curve or all three showing at the same time Parameter menu 1 Parameter menu Set menu Users can set or modify the unload voltage point unload current point RMP of fan stop input impedance range and initial charging voltage Password is needed when modify the parameters and factory default is 123456 2 Parameter menu Control menu lt can control the wind turbine Notes Password is needed when modify the parameters Enter the password and click OK twice when there is set successfully setting parameters is succeed otherwise it should be reset 7 Parameters Rated Battery Voltage 48V Rated Wind Turbine Voltage Rated Wind Turbine Maximum Power 1000W Input Impedance Range factory default 2 300 adjustable 60 R Wind Turbine Maxi ated Wind Turbine Maximum Input 0 40A current www neoenerji com Rated Wind Turbine Maximum instantaneous Input current Wind Turbine Charge Voltage factory Continuous Adjustable 8V default Unload Voltage factory default 52v 60V adjustable 54V Unload Current lt factory default 0 20A adjustable 18A 0 600rmp adjustable recover automaticlly 10 minutes later 500rmp Rated PV Maximum Power 600W 5mv C 2V Over Discharge Protection over discharge recovery Wind Turbine over Speed factory default Temperature Compensation voltage unload voltage compensation Control Mode Display Mode B Vol i
3. the first light control of first second loade of first lpad one load I 1 light control on and light control off load 1 light control on and light control off KKK Va output off 2 light control on and time control off output off 2 light control on and time control offe 3 continuously one 3 continuously one 5 4 Manual Brake Setting Press the Enter key and Esc key simultaneously LCD displays the symbol BRAKE that suggests fan is in brake status Press the Enter key and Esc key simultaneously in brake status the symbol BRAKE will disappear and the brake status is released In normal situation the fan can not be set in brake status 6 Control Software Process one Software Installation Double click WinController exe file click Install read the agreement of license click I agree if users agree to the terms and conditions Next Success Software installation process is same as general software installation process Process two Usage of the software 1 The choice of serial port By default the serial port is COM1 the 9 needles serial port back in the general desktop is COM1 Connect the RS232 interface of the controller to COM1 serial port of the computer with serial cable lf it is R8485 you need is a R8485 converter RS232 and then connect it to COM1 Connect the controller s power supply then open the software and complete the connection After the connection the light in bot
4. User s Manual Advanced Wind Solar Hybrid Controller Model WWS10A 48 Version 1 0 www neoenerji com neven erji Clean Energy AN Notes 1 Thank you very much for purchasing Wind Solar Hybrid Controller made by Neoenerji Corp Please read the instructions carefully before installation and usage and keep it properly 2 The installation operation must be done by experienced technical personnel and be strictly in accordance with the using manual to ensure the product can work properly 3 This product should be avoided long term exposure to corrosive gas and moisture environment 4 Do not put this product in wet rain exposure severe dust shock corrosion and strong electromagnetic interference environment 5 Do not open the shell to repair this product by yourself www neoenerji com 24 CONTENTS tE FEN 1 2 MEDINA 2 EG PAU EEE NT stein 3 4 0116 1 0 0 T 1m 216 01 1110 0 s sorsi er aea a Ea EE EAEE ea ERREEN EES 3 5 LCD Operation and Display Instructions aaan eneen eener enennneenen enen envensrenen eneen rene 4 Ol DEN EIKEN eneren 4 5 2 Displaying Contents Description one eneeneeenenenvenenennnnennen enen envensvenenneen eneen enn 5 5 3 Browsing Parameters and Output Modes Description aanne eneen enen ener eneen nnen 5 Oe Mente EE ER ao EEE neven eonn reren etste eeen 6 Bx SES OE EEG 6 Tae WAV AMC LONG EEE ETE A EE an nee 8 8 Abnormal Phenomenon and Treatment annen ee ee eee cnet eee e ena e te
5. ase seen enn ene eneen eens 10 www neoenerji com 1 General Description The advanced wind solar hybrid controller is specially designed for high end small scale wind solar hybrid system and especially suitable for wind solar hybrid power generation system system and wind solar hybrid monitoring system It can simultaneously control the wind turbines and solar batteries on the battery for safe and efficient charging The controller adopts PWM to control wind turbine and solar cell charge the battery with voltage limitting and current limitting namely the controller will charge battery with current limitting when battery power is low and charge battery with voltage limitting when battery power is high When the total charge current of wind turbine and solar cell is lower than current limitting point the controller will charge the battery with the whole power generated by wind turbine and solar cell When the total charge current of wind turbine and solar cell is more than current limitting point the controller will charge the battery with the current limitting point the excess energy will be unloaded by PWM When battery voltage is lower than voltage limitting point the controller will charge the battery with the whole power generated by wind turbine and solar cell When battery voltage is up to voltage limitting point the controller will charge battery with voltage limitting point and the excess power will be unloaded by PWM For specify wind tu
6. e wind turbine in brake status and then connect the output line of the wind turbine to the WIND INPUT terminal in back panel 4 Cover the solar panel with a shelter and the connect the solar panels to the SOLAR INPUT terminal in back panel 5 Install remote control software then connect RS232 or 485 interface to computer by data connection The computer will display the system parameters 6 Users can check the parameters through the key of LCD 5 LCD operation and Display Instructions Picture 3 the key of LCD 5 1 Description of the Key Press any key LCD backlight lights The backlight will auto off while stop pressing the key 10 seconds later oC en key symbolizes increase or next one In browsing window press this key to display next parameter Press this key to look the next parameter which can be modified or increase the value of the current parameter e vO key symbolizes decrease or previous one In browsing window press this key to display the previous parameter In setting window press this key to look the previous www neoenerji com parameter which can be modified or decrease the value of the current parameter e Enter key symbolizes set or confirm key In browsing window press this key to access setting window In setting window press this key to save parameter and return to browsing window e Esc key symbolizes cancel or manual switch In setting window press this key to retur
7. i i i Display Parameters attery Voltage Wind Turbine Voltage PV Voltage Wind Turbine Current PV Current Wind Turbine Power PV Power Etc Communication Interface Module RS 232C RS485 is selection Range of working Temperature amp Humidity 20 55 C 35 85 RH Without Condensation Quiescent Current 20 2 mA 100mA if the interface is RS485 Solar cells reverse charging solar cells anti reverse battery over charge battery over discharge battery anti reverse Overloading lightning protecting wind Protection Type turbine current limitting wind turbine automatic brake and manual brake 0 www neoenerji com 8 Abnormal phenomenon and treatment Phenomenon Description The symbolllnashino Battery is over voltage check battery voltage and the cable is without charge or connected or not reconnect all components discharge a First of all Parameter menu Control menu through the software to see if set to brake cancel the brake status LCD controller always b Brake state is usually caused by over speed of wind turbine It will displays brake automatically return to normal after 10 minutes under normal circumstances BRAKE and the c If not the above first disconnect the fan and controller and then manual can not cancel disconnect the battery and controller After a few minutes to start re wiring work observing whether it has returned to normal If the phenomenon
8. isplays the wind turbine s parameters followed by current voltage power quantity of electricity The bottom right corner shows the light and the speed of fan The light shows yellow and character No Signal when there is no signal green and character Normal when there is signal red and character Unload when controller is unloading red and character Low Battery when battery is low voltage The interface displays the speed of fan when the system works well Menu Bar Instruction Viewing saving and deleting of power www neoenerji com File The month consumption to see the electricity of the month 2 File Inquire electricity to see the previous electricity 3 File Save electricity to save the electricity of the month 4 File Delete the electricity of the month Set menu 1 set menu Serial port menu select the port 2 set menu Background menu set the company name and main form 3 set menu scale menu set the scale of P T curve and U T curve 4 set menu speed of fan menu select fan speed showing or no fan speed showing 5 set menu system selection select 12V system or 24V system in controller system bar and select Chinese English or English LCD display interface in LCD interface View menu Users can select which curve will be displayed in the pull down menu of View menu There are battery curve
9. mple structure powerful function stable performance gt PWM charging with voltage limiting and current limiting users can set the stop rotation speed of fan precisely gt Optional step up charging module the module s input impedance and the beginning charge voltage can be adjusted to suit the fixed feature of the different wind turbine gt Optional RS232 RS485 interface output gt TVS lightning protection gt Using the LCD professionally designed for wind solar hybrid street light The LCD can displays all system status and system parameters with intuitive digital and graph gt Perfect protection function 4 Operational Regulations The wind amp solar hybrid system connection diagram a is as follows After wind solar hybrid generator system and the various components of photovoltaic panels installed and the construction of the external circuit completed the following order should be carry out to make the connection and operation safely and reliably www neoenerji com 1 Open the package and ensure whether the equipment is damaged due to transportation or not 2 Connect the battery s positive pole to the positive of BATTERY terminal and connect the battery s negative pole to the negative of BATTERY terminal with copper core cable section surface gt 6mm and length lt 1m Despite the controller has the battery reversed protection but reversing battery is still forbidden 3 Make th
10. n to browsing window and do not save the modification In browsing window the key is as a manual reset key when the load short circuit or overload occur 5 2 Displaying Contents Description LCD screen displays the following picture Arm Er f O SET BRAKE VIND Pv 2 B888 S 1 N symbolizes the wind turbine 2 XX symbolizes the day 3 symbolizes the moon 3 symbolizes the battery internal strip graph represents the status of battery power When the battery is full 5 power bars in the battery box will show all the instructions When the battery is over voltage the symbol E flashing the flashing will not stop until over voltage s recovering 4 8 0 0 B is parameters showing The LCD can displays system parameters with intuitive digital 5 3 Browsing Parameters and Output Modes Description 1 Turn on the power the LCD displays browsing window and battery voltage XX X V 2 In browsing window LCD will circularly display the following parameters by pressing Pt key battery voltage wind turbine voltage photoelectric voltage wind power PV power wind turbine current PV current and so on LCD will display parameters in reverse order by pressing PC key Notes The controller just uses liquid crystal to display some www neoenerji com Voltage of light control one voltage af The time Controlling output model of the The time Controlling output model of
11. nder low speed Because the wind turbine has low energy at low speed so the charging current should not be too large when the fan speed is slow The low voltage charging module enables the wind turbine to charge the battery with constant input impedance under low voltage charging status namely the charging current is proportional to charging voltage Depending on the different characteristics of wind turbines the input impedance can be modified through serial communication In addition users can set wind turbine start charge voltage point through serial communication Only when the wind turbine voltage is greater than the wind turbine start charging voltage the wind turbine will charge the battery The wind turbine start charging voltage can be modified through the serial communication The controller has intelligent and modularized design simple structure powerful function The controller use high quality industrial components and excellent production activity which make the controller is suitable for relatively poor working environment and has reliable performance and service life 2 Model Description WWS XX A XX L Rated Battery Voltage Advanced Rated Wind Power e g 10 represents the rated wind power is 10 x 100 1000W Solar Power Wind Power Alternative Power eg WWS 10A 48 Advanced Wind Solar Hybrid Controller Battery Voltage is 48V www neoenerji com Q3 Features gt intelligently and modularized design si
12. rbine the controller can achieve accurate speed control namely you can set the stop rotation speed When the wind turbine exceeds this speed the controller will stop the wind turbine working and the controller will not run the wind turbine untill 10 minutes later The controller adopts LCD module especially designed for wind solar hybrid system The LCD can display battery voltage wind turbine voltage photoelectric voltage wind power PV power wind turbine current PV current and battery power status Users can browse the parameters through the four keys of LCD The controller is equipped with dedicated remote monitoring software The software can monitor system status in real time such as battery voltage wind turbine voltage solar battery voltage battery charging current wind turbine charging current solar charging current battery charging power solar charging power wind turbine charging power fan speed and so on The software can configure and modify the system parameters while the software can control running status of wind turbine and load www neoenerji com In addition the controller has perfect protection functions including solar cells reverse charging solar cells anti reverse battery over charge battery anti reverse lightning protecting wind turbine current limitting wind turbine automatic brake and manual brake The low voltage charging module is optional The module will enable wind turbine to charge the battery u
13. tom right corner of the software is green and the status bar up the light displays Normal If your computer is not COM1 you can set it by the following step Q Firstly identify your computer s serial port Right click My Computer Properties Hardware Device Manager Ports check your serial port 2 Open the software click Set menu serial port popup the dialog box and select your serial port www neoenerji com Graphic Displaying Instruction Chant P T shows the relationship between power and time the horizontal axis represents time I the vertical axis represents power W Chart U T shows the relationship between voltage and time the horizontal axis represents time T the vertical axis said power U Chart P T U T is a polar chart of power time and voltage time The chart shows the date and the time at the same time The interface of the software instruction Remote Management File Setup E View Parameter P Language L Remote management of Wind Solar hybrid Controlle PT th toda EE ME oo KE erm EN KEN mn Serialport normal Transmit Number Valid data Have Singal Normal Parameters Displaying Instruction The first column displays battery s parameters followed by current voltage power quantity of electricity The second column displays solar energy s parameters followed by current voltage power quantity of electricity The third column d
Download Pdf Manuals
Related Search