Pro 1800 LED
Contents
1. the headlamp mounting bracket and battery are securely fastened e Always disconnect the battery from the headlamp when transporting the light system PROTECTING YOUR INVESTMENT Properly charge your battery to maximize its lifespan see the Battery Charging and Care section for detailed information The Pro 1800 Race will perform in wet weather conditions but submerging it in water will damage the system NiteRider SUPPORT Technical Lighting Systems If you experience difficulties during product installation or operation NiteRider provides free telephone support on weekdays from 8 00 AM to 4 30 PM Pacific Time at 800 466 8366 ext 4 You may also e mail us at support niterider com WARRANTY NiteRider stands behind its products with the following warranties e Lifetime warranty on all mechanical components e 2 years on electrical components e 180 days on rechargeable batteries To obtain warranty service it is preferable to have your original sales receipt Contact the NiteRider customer service department at 800 466 8366 ext 4 to obtain a Return Merchandise Authorization RMA number The RMA number must be prominently displayed on the outside of your package The product must be properly packaged to prevent damage in transit For complete warranty information please visit our website at www niterider com RUN TIMES The Pro 1800 Race will run up to Time Lumens Light Level High 1 30 1800 M2. Fuel Gauge The 8 step LED fuel gauge is located on top of the headlamp in front of the power button When all four LED s are lit solid green the battery is fully charged As the battery discharges increments of Capacity the LED s from right to left successively go from solid to blinking green to out With only the final s capacity remaining one LED blinks red At this time the headlamp should be turned off and the battery recharged BATTERY CHARGING 1 Plug the AC Power Adapter into an electric outlet then plug the cable from the AC Power Adapter into the Battery 2 The indicator light will be red until the battery is fully charged then it changes to blue 3 Unplug the AC Adapter from the Battery by grasping the connectors rather than the cable 4 Leaving the Battery and AC Adapter connected indefinitely will not harm the batteries 5 When storing for an extended period of time charge battery every three months to maximize battery life RIDING AT NIGHT While a Pro 1800 Race lighting system will improve your view control and enjoyment of night riding please remember that cycling at night is an inherently dangerous activity In addition to using your lighting system properly and riding with extreme caution NiteRider urges you to e Never ride alone e Always let someone know where you are going e Wear a helmet and reflective clothing e Carry an auxiliary light and emergency supplies e Make sure
3. cess the daylight saftey flash mode press and hold the power button until the headlamp starts to flash 4 With the headlamp in flash mode press and release the power button to access Beacon S O S or Walk From walk mode you can return to normal mode by pressing and releasing the power button 5 To turn the headlamp off from normal flash or walk modes press and hold the power button until the headlamp shuts off 6 Always disconnect the battery from the headlamp when transporting the light system to prevent accidentally turning on the headlamp which may cause overheating and potential damage from high heat or even a risk of fire
4. ed 3 00 700 Low 6 00 400 Walk 25 00 80 Run Times are approximations and will vary NiteRider Technical Lighting Systems Inc 8295 Aero Place Suite 200 San Diego CA 92123 www niterider com 150 22842 Rev A PRO 1800 RACE USER GUIDE DISCOVER THE NIGHT Thank you for choosing the Pro 1800 Race from NiteRider the innovator in technical lighting systems The Pro 1800 Race combines a high powered white LED headlamp and a Li lon Battery To get the most from your NiteRider light we urge you to familiarize yourself with the following safety and operating instructions PARTS LIST AND IDENTIFICATION Please verify the contents of your Pro 1800 Race system Pro 1800 Race Headlamp Li lon Race Battery 4 cell 7 4v 5 2aHr Universal Handlebar Mount UHM Helmet Mount 36 Extension Cable A C Adapter nmo MOUNTING THE HEADLAMP The Pro Series headlamp can be mounted to the handlebar or tk a helmet Universal Handlebar Mount The Universal Handlebar Mount UHM is designed to fit on virtually any handlebar Included with the mount is a 2 5 mm Allen cc ten T wrench for adjusting the mount N a 1 Turn the knob counter clockwise allowing the hinge to swing open SCREW 2 Place the UHM on the ew handlebar on the left side the stem orienting the rectangular notch in the slider clip to the rear SLIDER CLIP 3 Swing the hinge down to make contact with the handlebar 4 Swing the bo
5. lt up seating the knob into its recess 5 Turn the knob clockwise to tighten and secure the mount to the handlebar The UHM can be adjusted to accommodate any handlebar angle By loosening the 2 5 x 30 mm Allen screw you can move the swing arm back and forth to straighten the headlamp Tighten the 2 5 x 30 mm screw after the adjustment To pivot the headlamp loosen the 2 5 x 12 mm screw located under the slider clip and swing arm and rotate the headlamp to the desired position Make this adjustment before tightening the 2 5 x 30 mm screw Inserting the Headlamp into the Handlebar or Helmet Mount Insert the headlamp into the handlebar or helmet mount slider clip from the rear forward Gently rocking the lamp as you slide it may help Do not push the release lever when inserting the headlamp into the slider clip let the lamp snap into place by itself Release Lever To remove the headlamp push the release lever forward and slide the lamp backward Note After mounting the headlamp adjust it so the beam illuminates the road properly without distracting oncoming riders Helmet Mount 1 Unclamp the straps on each side of the helmet mount and pull them free 2 Position the plastic mounting plate as close to the centerline of the helmet as possible orienting the parallel grooves on the slider clip to the rear 3 Feed each strap into and out of two helmet vents circling each strap back to the upper edge
6. of the corresponding Clamp 4 Fasten the straps by inserting them into the clamps and snap shut a MOUNTING THE BATTERY SYSTEM Warning For safety reasons a cyclist should never be tethered to the bike If the headlamp is mounted to the helmet do not mount the battery to the frame Conversely if the headlamp is mounted to the handlebar do not place the battery in a pocket or pack Frame Mount 1 Thread the Velcro straps through the 2 slots on the bottom of the battery tray 2 Attach the concave surface of the tray to a safe convenient location on the frame typically under the top or down tube placing the Velcro strap over the tube but under any shift or brake cables The cable from the tray should extend toward the stem 3 Secure the headlamp and battery cable to the frame using the thin Velcro strapettes Make sure the cables do not interfere with any moving parts Pocket or Pack 1 Route the 36 extension cable through a helmet vent or along the outside of the helmet using the thin Velcro strapette to secure the cable 2 Connect the 36 extension cable to the battery making sure the cable does not interfere with any moving parts 3 Simply place the battery in a pocket or pack OPERATION 1 Connect the headlamp cable to the battery 2 Press and release the headlamp power button to turn the light on Cycle through the three brightness levels by pressing and releasing the power button 3 To ac
Download Pdf Manuals
Related Search