User Manual
Contents
1. 11 3 8 16 Threaded Rod 12 3 8 16 Nut 13 3 8 ID Washer 14 Top Press Plate 15 Bottom Press Plate 16 Alignment Pin 17 Outside Double Press Cylinder 18 Compression Spring 19 Spring Plunger 20 Base Bushings INCLUDED ITEMS 1 Mechanical Frappe Press 5Four ER ee Part Trays 1 Hand Tool a lt a 2 m s y gt x gt Py tie AA Fee lt Fag g mr vs D a4 TA vagal a 7 ht wer dre 3 s gt BASIC OPERATION MECHANICAL PRESS OPERATION Place the mechanical press on a sturdy level surface with the given non slip pads Ensure the press is in a comfortable position to press the handle without adding unneeded stress to the arm and body 2 For ease of operation place the four part tray 1 on the base plate 10 before the flip caps are added to the tray as seen in Figure 1 Figure Tray Placement in Press 3 Take four clean flip caps and insert them into the four part tray 1 as shown in Figure 2 The cap should fit into the designated cap slot Make sure that the outer lip of the cap sits on top of the tray with the flat part facing down Outer Lip on Tray Flat Part of Cap Facing Down Cap in Cap slot Figure 3 Flip Caps in Tray 4 Insert the duckbills into the four part tray as shown in Figure 4 The duckbills should have the nipple facing up and set into the outer ring of the flip cap Nipple Facing Up2. Good job overall and good use of pictures to illustrate the operation The Maintenance section could be improved with pictures and the replacement parts list is incomplete Mechanical Frappe Press Operation Manual CONTENTS OPERATIONAL INSTRUCTIONS PRECAUTIONS PART NAMES INCLUDED ITEMS BASIC OPERATION MAINTENANCE REPLACEMENT PARTS Thank you for using The Frapptastic Five Mechanical Frappe Press Please read this manual carefully before operating This manual should be kept in a safe place for referencing its uses PRECAUTIONS WARNINGS BEFORE USE Never insert hands or other body parts inside the moving components Doing so could result in injury if the press handle were to fall or be pressed down 2 Do not use press for anything other than the intended use Pressing objects other than Frappe valves could damage or break the press which could potentially cause injury to the user 3 Keep your hands and other body parts away from moving parts especially on the handle when the press is in use Failure to do so could result in pinching or more serious injury 4 Only use the press on a sturdy level surface If operating on a portable table the structure must be able to withstand 351b Failure to do so could cause the press to work improperly or fall potentially causing injury 5 Never allow someone else to press the handle while you are handling the tray Serious injury can occur 6 Do not operate th
3. a pir g P i p B Duckbill set inside outer ring lle Figure 4 Proper duckbill alignment 5 Ensure that the press handle 4 is all the way up using your hand to hold it in place Slide the four part tray into the press until the front of the tray lays firmly into the spring steel indicator For further indication of alignment make sure that the back of the tray 1s flush with the marked line as seen in Figure 5 Ensure the handle is all the way up before moving the tray Align the back of the tray with d the marked line on the press E Figure 5 Proper tray placement 6 Press the handle all the way down until it is vertical as seen in Figure 6 Press linkage should be linear Figure 6 Press in down position If the user is unable to complete the pressing motion please pull the tray out and remove one or more of the assemblies to reduce the required force for the pressing motion 7 Ensure that the handle is all the way up before sliding the tray back out Slide the tray out of the press and inspect that all of the duckbills are properly seated in the flip caps per manufacturer s requirements Place the retaining rings on the duckbills with the slots properly lined up with the duckbill nipples Each of the retaining rings should rest on top of the duckbills with the flat side facing up The retaining ring should set inside the outer ring of the flip cap Use Figure 7 for a visual Always follow the manufa
4. akening causing too less of a force to push the flip caps back into the tray This can be done through the following steps Pull the 10 screws out of the Top Mounting Plate 3 using a Phillips head screwdriver Once the Top Mounting Plate 3 is off of the press frame flip the removed sub assembly over so that the Double Press Cylinders 17 and Alignment Pins 16 are facing toward you The Nut 12 on the bottom side of the Bottom Press Plate 15 can be removed with a 3 8 socket Once the Nut 12 1s removed the Top and Bottom Press Plates 14 and 15 can be slid off of the Threaded Rod 11 Remove the Top press Plate 14 from the Bottom Press Plate 15 and the springs will be present Remove the springs and replace with recommended springs Install the Top Press Plate 14 and slide it back onto the Threaded Rod 11 up against the Nut 12 Thread the bottom Nut 12 back onto the Bottom Press Plate 15 with the 3 8 socket to a snug fit Place 3 back onto the press frame and insert the 10 screws to a snug fit to lock the Top Mounting Plate 3 back into place REPLACEMENT PARTS part Name Number Supplier Supplier P N 3 8 16 Threaded Rod 11 Any Hardware Store 3 8 16 Nut 12 Any Hardware Store 3 8 16 ID Washer 13 Any Hardware Store
5. cturer s standards for lining up the retaining ring The flat part of the retaining ring must be facing up The slit in the duckbill must be lined up with the duckbill nipple Retaining ring should setontopofthe duckbill and rest inside the outer ring of the flip cap Figure 7 Proper Retaining Ring Alignment 9 Repeat steps 5 and 6 to press the retaining rings into the final assembly 10 Ensure that the handle is all the way up before sliding the tray back out Slide the tray out of the press and inspect that all of the retaining rings are properly seated in the flip caps per manufacturers requirements 1 1 Remove the completed assembly by dumping the parts into their assigned completed parts box for inspection as shown in Figure 8 Figure 8 Dumping of tray 12 Repeat steps 2 11 as needed HAND TOOL OPERATION Insert four flip caps into Four Part Tray 1 The cap should fit into the designated cap slot Make sure that the outer lip of the cap sits on top of the tray with the flat part facing down Also shown in step 3 of the press operation 2 Insert the duck bills into the flip caps Align the nipple on the duck bill with the lid on the flip cap Also shown in step 4 of the press operation 3 Hold hand tool by the base and press duck bills into place vertically while using a rolling motion to seat the entire duck bill into the flip cap The hand tool will press the inside and outside of t
6. e press without the front and back safety guard on Failure to do so could cause extra risk of injury to the user and increase the chance of damage to the press 7 If pain or discomfort occurs during use stop and consult a medical professional before continuing use CAUTIONS FOR USE Always inspect press components such as trays outside double press cylinders top and bottom press plates vertical mounting plate and front and rear triangle supports and scan other areas for cracks or malfunctioning parts before and during use Damaged or malfunctioning parts could cause the press to work improperly or break 2 If the alignment pins do not properly line up with the tray maintenance may need to be performed before using press see the Maintenance section of this manual NEVER force the press down Doing so may cause damage to the press and injury to the user 3 Check to ensure the non slip surface on the bottom of the press is not worn or torn prior to use If the non slip surface is damaged the press may slip and cause injury 4 Never disassemble or reassemble the press without proper training Disassembling or reassembling the press without proper training could cause alignment or safety issues PART NAMES p Four Part Tray Front Guard Top Mounting Plate Press Handle Vertical Mounting Plate Front Triangle Support Rear Triangle Support Rear Guard N A AA A amp N Side Guide Plate 10 Base Plate
7. he duck bill in place with this single motion 4 Align the retaining rings so that the slot fits over the nipple on the duck bills 5 Hold hand tool by the base and press retaining rings into place with a vertical force The hand tool can be pressed in a rotation motion to help insert the retaining rings ae 7 T ee al LE a 2e Ter Le 2 re e Sat ee Sa ae i ae pa 6 Make sure that the retaining rings are properly seated into the flip caps 7 Dump the tray of finished parts into the bin MAINTENANCE Does the Press Handle 4 not slide smoothly Lubricate shaft sleeve with a light film of Dupont food grade lubricant Do the Alignment Pins 16 bind or rub against the Base Plate 15 Base Bushings 20 and or Four Part Tray 1 Remove Front Guard 2 by unscrewing the 3 screws This will allow hand access into the pressing area Grab the Alignment Pins 16 with one hand while firmly holding onto the press with the other Slowly spin the pressing system to the correct alignment position so that the Alignment Pins 16 will go through the Four Part Tray 1 holes and Base Bushings 20 smoothly It may be difficult to spin the Alignment Pins 16 due to the Nut 12 being tight The Alignment Pins are still capable to be adjusted Replace Front Guard 2 and the 3 screws Does the press not fully snap the retaining rings into the flip caps If it appears that the problem is due to the Ou
8. tside Double Press Cylinder 17 not pressing far enough Pull the 10 screws out of the Top Mounting Plate 3 using a Phillips head screwdriver Once 3 is off of the press frame flip the removed sub assembly over so that the Double Press Cylinders 17 and Alignment Pins 16 are facing toward you The Nut 12 on the bottom side of the Bottom Press Plate 15 can be loosened with a 3 8 socket The Nut 12 on the top of the Top Press Plate 14 can then be screwed either out to lower the press or further into the Threaded Rod 13 toward the lever to raise the press depending on the resulting press height Once the Nut 12 is in the correct place screw the bottom Nut 12 back onto the Bottom Press Plate 15 with the 3 8 socket to a snug fit Place 3 back onto the press frame and insert the 10 screws to a snug fit to lock the Top Mounting Plate 3 back into place Are there valve components stuck on the inside of the pressing area Slide the Four Part Tray 1 through the pressing area to push any loose parts through the back of the press If the parts are stuck to the Outside Double Press Cylinder 17 remove Front Guard 2 by unscrewing the 3 screws This will allow hand access into the pressing area Are the duckbills not pressing firmly into the flip cap or is the flip cap sticking to the Outside Double Press Cylinder 17 The Compression Springs 18 may need replaced due to the springs we
Download Pdf Manuals
Related Search