Installation and User Manual
Contents
1. be mounted on the motor and then connected to the ACCO1 as shown on the wiring diagram page Addendum Shutter Door Applications cont Motor Preparation Steps continued The shutterdoor motor is supplied with a wall control console which consists of three buttons which allow the user to raise lower and stop the door It is of the wired type and looks identical or similar to the one shown as follows HSI1ON3 Wired Control Console The ACCO 1 when installed with the SHUTTERDOOR firmware allows control of the shutter door motor as per normal by simply connecting the wires of the control console directly to the ACCO1 Before that can be done it is necessary to determine which wires are connected to the buttons by using a multimeter UP OPEN STOP EN CLOSE Internal Wiring Diagram of Control Console Addendum Shutter Door Applications cont Motor Preparation Steps continued Control Console Connections continued HSI1ON3 From the diagram it is clear that the open and close or up and down buttons are normally open contacts whereas the STOP button is a normally closed contact NB The colour code shown is frequently correct unfortunately there may be variances so it is important to check which wires are connected to which buttons to ensure no installation errors occur Using a multimeter determine which two wires are shorted and then press the STOP button to confirm that the2. JO s 4 lt r gt O m m 2 2 S gt n SSS 1 2 Os High Voltage Side Terminals amp Descriptions WARNING The Lamp Relay contact is not fused fuse or E Earth suitable circuit breaker MUST be N Mains Netural L Mains Live Conductor used in the lamp circuit to prevent damage the ACCO1 FWD Motor Forward Winding N Motor Neutral or common REV Motor Reverse Winding Motor Capacitor The motor LAMP capacitor should be connected Contact across the FWD and REV B Contact Potential Free Relay Contact for Pillar lamp or other use terminals Y This card must be earthed via the E terminal otherwise the effectiveness of the lightning protection will be severely impaired HSITSNA ACCOT Detailed Description Low Voltage Signal Side Terminal Descriptions Pin Name Description Function TRIG MAIN TRIGGER INPUT Controls the Motor in the sequence of Forward gt Stop gt Reverse gt Stop This input is protected against lightning and may be used over a distance i e intercom handset PED PEDESTRIAN INPUT Opens the gate door approx 1 5th of the total travel Initiates a warning by causing the lamp relay to flash before starting the motor IRB SAFETY BEAM INPUT Input for a safety beam Normally Closed circuit that will either stop or reverse the motor depending on state During Forward opening
3. a maximum of 240 seconds 4 minutes with the pot turned fully clockwise Notes about auto close Turning the control fully anti clockwise until it stops turns off auto close completely Turning the control slightly clockwise sets auto close time to the minimum about 15 seconds Turning the control fully clockwise until it stops sets auto close to 240 seconds or four minutes It is MANDATORY to have a safety beam connected to the system when using auto close as this will prevent accidents and collisions from occuring with a gate that could open at any time Pedestrian mode auto close is not adjustable therefore this setting does not affect the pedestrian gate door in any way Even if auto close is fully disabled the pedestrian gate door will still auto close Auto Close Override Facility If auto close is enabled it may be temporarily disabled that is for the current gate door cycle by pressing and holding the TRIGGER or the remote control for 5 seconds when opening the gate door from the FULLY CLOSED state When the trigger is held for 5 seconds at least the gate door will stop and pause providing acknowledgement that the override has been set When the trigger is released the gate door will resume opening and open fully and remain so until commanded to close by a trigger When commanded to close and the gate door reaches its closed limit the override set will be cleared and auto close will become operational again P
4. cycle the input is ignored During Reverse closing cycle the input will cause the motor to stop pause a short while and then reverse During Open state activation of this input resets the auto close timer if enabled If not used this input must be tied to COM with a wire link LED STATUS LED OUTPUT A Status LED output designed to drive an external remote LED inside an intercom handset over a distance The pin is protected against lightning LIT LIGHT CONTROL INPUT Control input for manual control of the lamp relay from a remote location by using a push button Brief activation turns lamp on for the lamp time Press and hold for 5 seconds invokes override mode where lamp is permanently on FRX FREE EXIT INPUT A special trigger input that will cause the motor to drive forward open only It will also reset the auto close timer if the system is in the open state It will also cause a reversal stop and reverse open if the system is in the process of closing OLS CLS OPEN LIMIT SWITCH CLOSED LIMIT SWITCH Limit switch input Opening the circuit will register the open limit resulting in the motor stopping if it was travelling forward opening Limit swith input Opening the circuit will register the closed limit resulting in the motor stopping if it was travelling in reverse closing 12V AUXILLARY POWER SUPPLY Unregulated DC 12V output for auxillary equipment such as th
5. if the installer so wishes The next few pages go into detail on how to connect these motors to the ACC01 Addendum Shutter Door Applications cont Accessories Required for Installation HSITSNA MOTOR ADAPTER BOARD ADBO1b The motor adapter board is purchased separately In addition you will need suitable lengths of 1mm wire to connect the ACCO 1 to this board Preparing the Motor for Retrofit single phase models Virtually all the shutter door motors have a cover cup at the top end of the motor where all the electrical connections are made Within this space is a pair of relays or contactors depending on the manufacturer and motor type For a single phase motor there is usually two relays contactors present to which many electrical connections are made Prepare the motor for installation as follows 1 Remove the relays contactors completely and disconnect all wiring including the mains lead and wall control three button up down stop panel All that should remain is a wiring loom that runs into the side of the motor where a cover exists to hold the motor capacitor and two thin wires coming out the top The wiring loom will contain 9 wires which includes the three motor wires two wires to the thermal cut out and two pairs of wires one to each limit switch 2 Retain the plastic panel that held the relays as it will be used for mounting the ADAPTER BOARD which has holes to match those on the plastic pane
6. special shutterdoor variant is that provision is made for the inverted limit switches as well as the three button control panel which is usually supplied with these types of motors The ACCO 1 s wireless remote control receiver however works the same as previously and will provide the expected start stop reverse stop sequence There are two types of shutter door motor in existence one is a single phase model the other is a three phase variant the ACCO1 can be configured to operate either type The difference is how the connections are made Most shutter door motors include a magnetic clutch and to operate this clutch correctly requires the addition of an adapter board the ADBO1b which can be purchased separately from your distributor The ADBO1b provides the control voltage for the clutch ensuring it engages and disengages correctly when the motor is started and stopped It also provides a convenient bonding point for the existing motor wiring to the ACCO1 Shutter Door Motor Types the ACCO1 has been tested with Hualin Brand HL series single phase HL 200 1P thru HL 1000 1P J amp G Brand series motors Both these products are virtually identical from an electrical standpoint and operate on the same principle the differences being mainly mechanical These products often include a wireless remote control unit with remotes and a keyswitch which are not needed when the ACC01 is installed However these components can still be used
7. where a similar control card is used such as sliding gates swing gates shutter door automation and garage door automation systems The ACCO 1 is designed to work with limit switches which signal to the system when either the closed or open limit is reached Out the box the ACC01 is a drop in replacement for current and legacy mechanical actuators manufactured by REMEZ HANSA and others The advantage of the ACCO is that it features an on board code hopping receiver capable of storing up to sixteen unique buttons or transmitters The ACC01 is also capable of supplying large currents up to 1A on its auxillary supply terminal enabling the product to provide a supply for locks that are typically used on some types of swing gate The ACCO also features motor run timing which allows the motor to run for a maximum of sixty 60 seconds under all conditions This avoids damage to the motor should the limit switches fail The ACCO also features a PEDESTRIAN mode for gate applications Auto Close facility with override mode and a fully controllable pillar lamp relay All inputs are provided with STATUS indicators and a test button is included on the card itself The ACCO includes full lightning and surge protection as standard The motor relays are also protected against excessive arcing by zero crossing switching All connections are pluggable ensuring quick and easy replacement Pin connection order and signals are industry compatibl
8. ACCO1 UNIVERSAL SINGLE PHASE AC CONTROLLER CARD SENTRY Installation and User Manual Manufactured By Martin Electronics cc PO BOX 49284 ROSETTENVILE 2130 Republic of South Africa Vervaardig Deur Martin Electronics cc Posbus 49284 ROSETTENVILE 2130 Republiek van Suid Afrika Fabricado por Martin Electronics cc PO BOX 49284 ROSETTENVILE 2130 la Rep blica Surafricana Hergestellt durch Martin Electronics cc PO Kasten 49284 ROSETTENVILE 2130 Republik S dafrika POWERED BY oft 3 freescale semiconductor Technical Support For technical queries relating to use installation of this product 27 11 433 4084 Table of Contents Company PROTO 5 5 creen teen td ease ne cee sea 4 Warnings and Cautions for Use eese 5 CES 6 Product Description and Applications 6 Package contents and Optional Extras 7 Compatible Systems and Replacement 8 Required Equipment eese enenatis 9 Module Detailed Description 10 Card Features ccccccccccccccccccceeeeeeeeseeeeaeaeeeeeeeeeceseceeeeceeeeseeeeuenenea 10 Electrical Terminals and Descriptions 11 High Voltage Connections sssssssssese
9. CCO1 and replace it with a 1A quick blow fuse Return the ACCO 1 for repair testing Check for disconnection by bridging IRB terminal to COM If card operates then replace repair wiring Check beam and adjust repair as necessary Locate AC fuse F2 on the ACC01 and replace with a 5A slow blow fuse Replace the Motor Capactior with a similar type Test the motor without the presence of the ACC01 and repair replace if necessary Disconnect all wiring from the 12V terminal Replace fuse and if the card powers up investigate for short circuits on the auxillary line Return the ACCO 1 for repair testing Addendum Shutter Door Applications Using the ACCO1 to control Shutter Door Motors The ACC01 is a suitable candidate for controlling generic shutter door motors In most cases the motor will need to be modified to work with the ACC01 this entails modifications to the wiring and removal of some unnecessary components from the shutter door motor This section is intended for professional installers who supply and fit a range of Chinese shutter door motors which are of the tubular type HSI1ON3 To operate the available types of shutter door motor requires the ACCO 1 to be supplied with a special software installation This can be done on production when you order your ACCO 1 or you can return the board to your distributor and request that the SHUTTERDOOR software be installed The difference between normal software and the
10. ation Step 1 amp 2 22 Motor Wire Functions innt ir tin 23 Lirfut SWIIChes e rint nee na ei ni 25 Control Gonsole te ea 27 Wiring Diagram Single Phase sse 29 Product Specification 30 Technical Specifications amp Dimensions 30 HSITSNA Company Profile Martin Electronics is a respected and well known gueeepess a manufacturer of RF HET HSITSNA remote controls and security MARTIN products and has i TEL 433 4084 SENTRY established itself as the leader in RF remote control for the past 20 years The company manufactures remote controls receivers infrared beams and garage door automation products under the Sentry brand name The company also manufactures products for OEM Original Equipment Manufacturers and custom markets and is deeply respected in this regard as it designs and manufactures not only its own products but specialised and custom products for specific customers and provides support for these products MARTIN ELECTRONICS strives to give service and backup second to none Technical staff as well as our engineers are available to give answers to technical or installation problems The equipment is installed countrywide and is available through a network of distributors in South Africa Further
11. cker wires included with two pairs of thinner wires one set is orange one set is brown note that colour variances may mean a different colour wire is used If one looks through the plastic cover you will usually be able to see that the one pair of thin wires is attached to one limit switch while the other pair is usually attached to the other limit Switch To Determine which limit switch is which Use a multimeter to determine which limit switch is open and closed limits respectively by measuring across wire pairs with the same colour an open circuit or OL reading indicates the door is on its limit So for example if the shutter door is closed the limit switch that is reading open circuit is the CLOSED LIMIT switch Make a note of which pair was open circuit and wire as follows Addendum Shutter Door Applications cont Motor Preparation Steps continued Limit switch unit internal wiring diagram HSITSNA The thinner wires are the BROWN BROWN and ORANGE ORANGE pairs The thicker wires are not used when connecting the ACCO1 and can therefore be cut off or taped up into the wiring loom Having noted which limit switch pair is the CLOSED LIMIT wire the limit switch pairs onto the ADBO 1 as follows n a We ID FO 5 TO 9 m OPEN LIMIT z z S SWITCH D Ps 3E TO CLOSED oh LIMIT SWITCH e Once these connections are complete the ADBO1
12. cturer to manufacturer HSITSNA FORWARD NEUTRAL REVERSE thermal THERMAL THERMAL mag brake NN e Note Reading C will usually be 2xAorB FREQUENTLY USED COLOURS THICK BLUE x 2 THERMAL CUTOUT THICK RED MOTOR FWD WINDING THICK YELLOW NEUTRAL THICK GREEN MOTOR REV WINDING THIN RED AND BLACK PAIR MOTOR BRAKE 0Q multimeter set to ohms Once you have determined the correct wire functions from the above tests the ADB01b can be connected to the motor wires as shown THERMAL THERMAL REVERSE NEUTRAL FORWARD 1SEQREN SNES Addendum Shutter Door Applications cont Motor Preparation Steps continued The next step is to connect the limit switches correctly and to confirm that they are working correctly These types of motor operate on an inverted limit switch principle meaning that the contact is broken on the switch when the limit is reached and therefore when the door moves away from the respective limit the contact is once again made HSI1ON3 The shutter door motors employ a mechanical limit switch mechanism which looks identical or similar to the following MECHANICAL LIMIT SWITCH MODULE The switches within this unit are of the double pole type therefore a total of eight wires including an earth exit from this unit There are usually three thi
13. e Finally the ACCO 1 is fully customizable for OEMs and for volume customers Please contact MARTIN ELECTRONICS for further details Applications Swing Arm Gates typically in ground type units Hydraulic Actuator Swing Gates FAAC etc AC Sliding Gate Motors Shutter Door Actuator Systems Curtain Actuation Systems AC Garage Door Actuator Systems Introduction HSITSNA 1 pc Controller Card and Instruction Manual Optional Extras SENTRY Code Hopping Remotes 1 3 4 Button SENTRY Utility Enclosure SENTRY Infra Red Beam IRB WO1 Introduction Compatible Systems For Replacement m The ACCO1 is compatible with the following actuators as a rough guide Other operators may exist that will work well with this product 5 Brand Model Number s Type s Swing Standard Swing Fast REMEZ Swing Heavy Duty 1103 Slidert 1105 Slidert 413 LS 415 LS FAAC Ferni 230V Version FAST 230V Version t CAME ZA3N Control Panel FROG A FROG AV HANSA DELUXE HANSA NICE VF Series using three phase contactors tt BONFIGLIOLI CP91 Controller Card CENTURION The above is not an exhaustive list In general any single phase AC motor fitted with limit switches is suitable for the ACCO1 Please bear mind the upper limit of the motor power is approximatel
14. e plastic platform as shown The mounting holes are indicated with arrows the ADBO1b is designed specifically to align with the holes that were used to hold the previous controls HSI1ON3 Mount the board as shown in the diagram using the screws that were removed when you removed the contactors relays and screw it down firmly into place Depending on which side the wiring harness into the motor is the ADBO1b can be installed either way round depending on your preference and your convenience Checking Motor Wire Functions At this point prior to wiring the motor into the ADBO1 adapter board it is necessary to confirm the wire functions on the supplied motor as variances are common due to the nature of the product The motor s internal wiring diagram is as follows FORWARD NEUTRAL REVERSE thermal THERMAL THERMAL mag brake HN C BRAKE BRAKE Thermal The motor is fitted with a thermal cut out switch which is used to protect the motor Mag Brake This is the electromagnetic brake used to stop the motor when power is removed preventing free race Applying DC power to these terminals disengages the braking mechanism Addendum Shutter Door Applications cont Motor Preparation Steps continued Confirm the motor wire functions using a multimeter set to measure ohms measuring between the points as shown Note motor winding and brake winding resistances are approximate and may vary from manufa
15. e lost or stolen remote controls HSI1ON3 Programming amp Advanced Features Lamp Control Input The ACCO 1 provides a lamp control input which operates in an industry standard manner via a push button or toggle switch Activating the input will turn on the lamp and another activation will turn off the lamp When the lamp is turned on the STATUS LED will indicate this by means of short duration flashes HSITSNA Troubleshooting Guide Basic Troubeshooting Guide for the ACCO1 The following is a basic guide to fault finding the ACCO1 In many cases working through these will solve common problems However when in doubt please call technical support or send the card in for testing repair either HSI1ON3 directly to MARTIN ELECTRONICS or via your distributor Problem No response to triggers AC ON LED does not light System unresponsive System powered up and appears to work but will not respond to a TRIGGER nor a FREE EXIT input Relays Click when triggered but gate door motor does not start DC side fuse F1 keeps blowing Possible Cause No AC Power DC Fuse Blown Card Faulty Beam Input Disconnected Faulty IR beam AC FUSE Blown Motor Capacitor Faulty Motor Faulty Short Circuit Overload on auxillary terminal Card Faulty Possible Solution Check for presence of AC mains if not present check for tripped circuit breakers upstream of the supply Locate DC fuse F1 on the A
16. e safety beams additional remote control receivers access control keypads etc Max current that may be drawn is 1A COM COMMON NEGATIVE Common terminal negative for signals and auxillary power supply 5 in total to an intercom handset via a long cable run as they are protected All other inputs T The TRIG input and LED output are the only two signals designed to be connected are not designed for use over long cable runs Failure to observe this will result in the risk of lightning damage to the 1 HSITSNA ACCOT Detailed Description General Connection Diagram m a Fuse Breaker 9 Pillar Courtesy Capacitor o Lamp e 1 ph LIVE NDS TT Motor i NEUTRAL OQOOOOOOQOO B A REV NFWDL N E Trigger Pedestrian Opening Safety B S by neue ERJ Fit wire link as shown 44 if beam is not fitted STATUS LED Isolator LIGHT CONTROL BUTTON Free Exit Opening Open Limit Switch XE Closed Limit Switch 2 To DC Output Distribution Point The ACCO 1 is equipped with diagnostic indicators that are useful for fault finding and verifying installation Normally Open Inputs TRIGGER PEDESTRIAN FREE EXIT These inputs have RED indicators that light when the circuit is closed Normally Closed Inputs IR BEAM OPEN LIMIT SWITCH EE CLOSED LIMIT SWITCH LIMIT SW 22208 These inputs have GREEN i
17. eeeeerennneenne 11 Low Voltage Connections sssesssssseeeeen eee 12 General Connection Diagram 13 ACCO1 Operational Details 14 Auto Close Fealure ntt tte E ERE 14 Auto Close Override iecit ete stet rtp ian 14 Pillar Courtesy nt eet ret ertt te eee zn 14 Pedestrian MOE eet nt e hh axe RR RE R 14 zn 14 Safety Beam 2 15 Status LED Output 2 rad ised a aere e eet 15 Zero Crossing Feature 15 Auxillary Power Output 15 System Programming and Advanced Features 16 Auto Close Setting sse 16 Auto Close Override Facility esee 16 Programming Remote Controls 17 Erasing Remote Controls esses 17 Lamp Control Button zt tete Er reete tec ie Lee dovete RE eeu 18 Troubleshooting Guide cesses 19 Addendum Shutter Door Applications esee 20 Shutter Door Software and Ordering Information 20 Accessory Board ADBO1b amp Motor Preparation 21 Motor Prepar
18. gainst lightning The status LED indicates system status as follows System State LED Indication Fully Closed LED is off Running Open LED flashes slowly 1 flash sec LED flashes fast 2 flash sec Pedestrian Opening LED flashes very fast 4 flash sec Zero crossing Switching To reduce mains borne switching noise and primarily to prolong the life of the control relays the ACCO 1 is equipped with zero crossing switching This means that the motor is switched on or off during the zero crossing point of the mains waveform While this does not entirely eliminate relay contact arcing it does substantially reduce the severe arcing that would otherwise result which if left uncontrolled leads to premature failure of the ACCO1 Auxillary Power Output The ACCO 1 can provide up to 1 Ampere of current for external equipment on its auxillary output terminal The output is protected by fuse F1 which is closely mounted to the signal connector Programming amp Advanced Features Programming the ACCO1 The ACCO 1 involves minimal programming aside from learning remote controls into the built in receiver Setting up the Auto Close Timer C12 The auto close time may be adjusted by turning the potentiometer located on the ACCO1 as shown Turning the pot fully anti clockwise will DISABLE the auto close timer completely Turning the pot clockwise will adjust the auto close time from between 15 seconds and
19. information is available on our website www martin electronics co za Martin Electronics cc 2009 Martin Electronics cc reserves the right to make changes to the products described in this manual without notice and without obligation of Martin Electronics cc to notify any persons of any such revisions or changes Additionally Martin Electronics cc makes no representations or warranties with respect to this manual No part of this document may be copied stored in a retrieval system or transmitted in any form or by any means electronic mechanical optical or photographic without the express prior written consent of Martin Electronics cc N WARNINGS AND CAUTIONS 1 PLEASE READ THE FOLLOWING WARNINGS AND CAUTIONS BEFORE INSTALLING OR USING THE PRODUCT RISK OF ELECTRIC SHOCK AND OR FIRE DO NOT TOUCH ANY COMPONENTS WHEN POWER IS APPLIED Read all instructions and warnings 9 carefully before installing the product The product must only be installed by suitably qualified persons NEVER allow children to play with the system or its remote controls 10 Secure all remote controls and opening devices to prevent unauthorized access to the display system Before attempting any work or maintenance on the product disconnect the power and remove the batteries if applicable 11 All modifications not expressly approved by the manufacturer are forbidden Do not install the product in an explosive atmosphere o
20. l Since these motors are manufactured in the Far East there are often variances in motor wire colours Always double check the wire functions before attempting to install the ACCO1 on these motors Addendum Shutter Door Applications cont Motor Preparation Steps Existing Controls Removed Once the relays contactors are removed all that remains is a plastic platform as shown alongside in the diagram Note the arrow pointing to the earth conductor which should be retained and attached to the EARTH terminal of the ACCO1 The plastic platform is to be kept in place as it will be used in the next step Motor Top Section with cover removed This is where the main control logic of the motor is to be found consisting of two relays or contactors The first step is to remove both relays contactors and superfluous wiring In some cases there will be a small PC board with some components this is the brake actuating circuit and can be removed Once you have removed all the wiring and components you should be left with two thin wires going down the top which are the brake wires and the main wiring harness going into the motor down a side hole and on to the limit switch unit HSITSNA Note Retain the screws used to mount the contactors relays as they will be re used Addendum Shutter Door Applications cont Motor Preparation Steps continued Fitting the ADBO1b The ADBO1b is designed to mount on th
21. m SENTRY MA ELECTRONICS
22. ndicators that light when the circuit is the correct state and turn off when the circuit is broken e g IR Beam is ums CLOSED broken LIMIT SW m m 1 The AC STATUS indicator is always on when the card is powered up AC jmd i it does not light it means there is no power on the STATUS _ 01 Operation ACCO1 Operational Details The ACCO 1 operates in an industry standard manner providing full gate door control via a trigger input The general method of operation is that each activation of the trigger will stop all motion if the gate door was in motion and will start the gate door moving if it was stationary HSI1ON3 Auto Close The ACCO 1 provides an auto close function which can be set between OFF and a maximum of four minutes Turning the shaft on the board fully anti clockwise will disable AUTO CLOSE Turning the shaft clockwise allows adjustment of the auto close time from a minimum of 15 seconds to a maximum of four minutes Auto close will close the gate door automatically if it was open or partially open Auto Close Override Mode The auto close mode can be overridden i e disabled for the current cycle by holding the TRIGGER trigger input or remote control continuously when opening the gate door from the fully closed position Once the remote trigger input has been detected as being held for 5 seconds or more the gate d
23. oor will stop as acknowledgement and when the remote control trigger input is released the gate door resumes opening The override mode is cancelled once the gate door is fully closed Pillar Courtesy Lamp The ACCO 1 provides a relay for controlling the standard pillar courtesy lamp When the gate door is triggered to open the lamp will be turned on When the gate door is stopped by either the user pressing the remote or it reaching its open limit the lamp will remain on However if auto close is disabled the lamp will turn off after two minutes The lamp also turns off 2 minutes after the last gate transaction is completed The LIT lamp control input allows for manual control of the lamp and is designed for connection to a push button Pressing the button briefly with the gate in the fully closed state will turn on the pillar lamp and it will remain on indefnitely This override state is indicated by short flashes on the STATUS LED Activating the input again clears this mode Pedestrian Mode The ACCO 1 provides a standard Pedestrian Key switch input When activated the pillar lamp relay will pulse for 5 seconds thereby flashing the pillar lamp as a warning that the gate door is about to open The gate door will then be open about 3096 of the nominal travel and then stop If the trigger input is invoked during the pedestrian mode running or when the gate door has opened partially pedestrian mode will be cancelled and the gate will o
24. pen fully as per normal Free Exit The ACCO 1 provides a free exit input which as the name implies allows only an exit condition This input will only invoke opening cycles and if the system is closing will _ACCO1 Operation ACCO1 Operational Details cont Free Exit cont result in a full stop a short pause and re opening known as a reversal If the gate door is fully open activation of the FREE EXIT input will reset the auto close timer if enabled Generally the auto close timer should always be activated when using the FREE EXIT input otherwise there will be no way of closing the gate door Safety Beam Input The ACCO 1 provides a standard safety beam input which is designed to prevent the gate door crushing or colliding with people objects in its path The beam input is a normally closed circuit which if not used must be bridged with a wire link between IRB and COM terminals The beam input will reset the auto close timer if the system is fully open and during closing a short beam break will result in a pause i e the gate door stops for about 1 1 2 seconds then resumes closing A longer beam break will result in a reversal and the gate door will re open fully Status LED Output The ACCO 1 has a standard STATUS LED output as well as an LED on board to indicate the status during installation testing The output pin is designed to directly drive a standard LED over a long cable run and is fully protected a
25. r any location subject to heavy 12 moisture ingress Never short circuit any wiring to and from this equipment for any reason The installer has a responsibility to explain to the owner user how the system operates and how to deal with potential emergencies that may arise during the scope and course of the product s application The installer must also pass on these instructions to the owner user The product is designed and manufactured only for the applications intended in this manual Any other use renders the warranty null and void and neither the manufacturer or its distributors affiliates servants etc shall be held liable for any loss or damages whatsoever This product is designed to be compatible with the systems indicated and updated from time to time Satisfactory performance cannot be guaranteed for systems that are not expressly listed as compatible Use of this product may render the warranty of the target system null and void unless use of this module is approved by the manufacturer or its authorized distributor Technical Support For technical queries relating to use installation of this product 27 11 433 4084 HSI1ON3 Introduction The SENTRY ACCO1 is a general purpose or universal AC Motor Control Card for general applications where it is necessary to control a single phase AC motor within defined limits HSITSNA It is designed to be a compatible replacement for systems
26. rogramming amp Advanced Features Programming the ACCO1 continued Programming Remote Controls The 1 allows up to sixteen 16 remote controls to be stored in its memory Remote control storage is automatically managed To learn a new remote control 1 Press and release the LEARN button on the ACCO1 The STATUS LED emits short flashes 2 Operate the button on the remote control you wish to program into the ACCO 1 at a distance of at least 1 metre away from the ACCO1 When successfully learnt the STATUS LED will turn on for 1 second Thereafter learn mode is exited and the product resumes normal operation To Erase all remote controls 1 Press and hold the LEARN button on the ACCO 1 2 After about 5 seconds the STATUS LED will flash slowly Release the LEARN button 3 The STATUS LED will begin to flash rapidly for up to 10 seconds as all data is erased When finished the ACCO 1 enters learn mode allowing a new transmitter to be learnt in at that point If the user does not wish to learn new remotes in at this point simply leave the ACCO 1 to time out after 10 seconds in which case normal operation resumes Learn mode exits automatically when either a remote control is learnt into the system or the system is left to time out after 15 seconds i e no remote is learnt into the system e It is not possible to erase an individual remote Only a mass erase of all remote controls can be performed to eras
27. short clears Either one of the wires could be a COMMON Using either of these press the UP OPEN button and search amongst the other wires until you find the correct one Note which of the two first wires gave you a reading this is the COMMON The control console is wired into the ACC01 as follows OPEN UP Button TRIGGER INPUT TERMINAL COMMON COMMON TERMINAL CLOSE DOWN Button PEDESTRIAN INPUT TERMINAL STOP Button FREE EXIT INPUT TERMINAL Addendum Shutter Door Applications cont Single Phase Wiring Diagram EUEN 1ulog uonnquisid 7 OL CUT MOTOR JOjejos Qe REU FWD FHO THERM eSesesses Yo 3H V 1 UO DAJIP 1294109 BU ui UIN 0j 10 OW 106 01 AJY pue GMA qrLogav dems y uonejeisui uo Hulpuedeq 910N motor side to motor EARTH chassis Product Specification Operating Voltage 200 250V AC 50 60Hz Motor Rating 650W max Auxillary Power Out 12 14V DC maximum load 1A Lamp Relay Contact 5A at 220VAC 500 watt tungsten load max 250 watt metal halide lamp wattage max Onboard Receiver 433 92MHz code hopping rolling code Card Dimensions 134 4 ALL DIMENSIONS IN MILLIMETRES HOLE DIAMETER 4m
28. y 650 watts Larger and three phase motors may be controlled by using two three phase contactors with single phase coils T The 1 may not fit inside the original enclosure but can certainly be mounted external to the actual gate motor i Not all features may be identical Tt Use of RVS Limit Switch Device is mandatory Required Equipment for Installation _ 9 Philips screwdriver amp Flat screwdriver 75 Small Side Cutter 9 HSITDNG ACCOT Detailed Description Card Features HSITSNA 1 High Voltage Side Terminals 6 On board STATUS LED 2 Pillar Lamp Relay Potential Free 7 Integrated 433MHz Receiver Module 3 Motor Relays 8 Antenna 4 Signal Low Voltage Side Terminals 9 Transformer 5 Auto Close Adjustment 10 LEARN Button operation It is always mandatory to isolate all power before working on any of the electrical connections Lethal Voltages Exist on this card module during normal ACCOT Detailed Description ACC01 Electrical Terminals and Descriptions HIGH VOLTAGE TERMINALS MARTIN ELECTRONICS ACCO REVI 1 WARNING ISOLATE BEFORE WORKING ON CARD Swi GA2 o 7 B EROR
Download Pdf Manuals
Related Search