Home

User Manual

image

Contents

1. lt 1617 gt 2 9 xxxxxx 1 2 9 xx 2 9 xxxxxx 011 2 9 x 3469 11 Explanation of example rule reading from left to right 41900x prevents dialing any number started with 1900 lt 161 7 gt 2 9 xxxxxx allows dialing to local area code 617 numbers by dialing 7 numbers and 1617 area code will be added automatically 1 2 9 xx 2 9 xxxxxx allows dialing to any US Canada Number with 11 digits length 011 2 9 x allows international calls starting with 011 3469 11 allow dialing special and emergency numbers 311 411 611 and 911 Note In some cases user wishes to dial strings such as 123 to activate voice mail or other application provided Oo Oo MM YO Unicorn 3112 User Manual Page 26 of 39 Firmware 1 0 0 46 Last Updated SUBSCRIBE for MWI Send Anonymous Anonymous Call Rejection Check SIP User ID for incoming INVITE Session Expiration Min SE Caller Request Timer Callee Request Timer Force Timer UAC Specify Refresher UAS Specify Refresher Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY by service provider In this case should be predefined inside dial plan feature and the Dial Plan should be x More information can be availabled at Dail Plan Notes Default is No When set to Yes a SUBSCRIBE for Message Waiting Indication will be sent periodically lf this parameter is set to Yes the From header in outgoing INVITE message will be set to anonymous essentially bl
2. Busy ON Solid Green Line Available OFF Fast blinking Ringing Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 14 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 y HAN TECHN G 0 0 lt LOG 6 CONFIGURATION GUIDE 6 1 Configuring Unicorn 3112 using Web Browser Unicorn 3112 has embedded Web server and HTML pages that allow users to configure the Unicorn 3112 through an easy to use Web browser interface such as Microsoft s Internet Explorer or Netscape browser Below is a screen shot of the Unicorn 3112 configuration page Admin Password Oppose not displayed for security protection pomene ER Layer 3 QoS 48 Diffserv or Precedence value Layer 2 QoS B021QVLANTag 802p priority value 0 7 STUN server is tr iP porp keep alive interval a n seconds default 20 seconds DEVICE STATUS BASIC OPTIONS Upgrade Via TFTP HTTP SUPER OPTIONS Firmware Server Path 192 163 0 98 FXS PORT Config Server Path 192 168 0 88 FXO PORT Firmware File Prefix Firmware File Poste Config File Prefix Config File Postfix Automatic Upgrade O No Yes check for upgrade every minutes default 7 days Always Check for New Firmware Check New Firmware only when FAY pre suffix changes NTP Server time gist gov KURI IP address Lock Keypad Update No Yes configuration update via keypad is disabled if setto Yes Firmware Upgrade a
3. Broadsoft Howdy WHAT IS IN THE PACKAGE The Unicorn 3112 package contains e One Unicorn 3112 VoIP adapter One universal power supply One Ethernet cable One phone cable Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 3 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 Ez m HANLON GG a ECHNOLOGY 3 PRODUCT OVERVIEW 3 1 Key Features e Supports SIP 2 0 RFC 3261 TCP UDP IP RTP RTCP HTTP ICMP ARP RARP DNS DHCP both client and server NTP PPPoE STUN TFTP etc Built in router NAT Gateway and DMZ port forwarding Supports call origination and termination from to the PSTN network via FXO Port Powerful digital signal processing DSP to ensure superb audio quality advanced adaptive jitter control and packet loss concealment technology Support various vocoders including G 711 a law and u law G 723 1 5 3K 6 3K G 726 40K 382K 24K 16K as well as G 728 G 729A B and iLBC Pending Support Caller ID Name display or block Hold Call Waiting Flash Call Transfer Call Forward in band and out of band DTMF Dial Plans etc Support fax pass through T 30 and T 38 Support Silence Suppression VAD Voice Activity Detection CNG Comfort Noise Generation Line Echo Cancellation G 168 and AGC Automatic Gain Control e Support standard encryption and authentication DIGEST using MD5 and MD5 sess Signaling and call encryption via TLS and SRTP enabling e
4. ccc ccccceecccceeeeseeeeeeeeeeseeeeeeeseeeeeeesseseessaeeeeeeeas 10 523 Blind VAST ON seasicceataseciecterdces lt tawsiniie camsamtcdaiisintehuickeninmed e Eien a ERES 11 529 Attended Tansel 5 ieee eee se eee et er pene en er ER 11 5 2 10 Send and Receive PSTN CalllS ccccceecccecceeeeeeeeeseeeeseeeeeeeeeeeeeeeens 12 5 211 VOIPIO PSTIN Galles aben ke rasen dere R RATAR ANRE 12 52312 PSTNHONO IP GAS 0 arrene ee eee ene ene 12 5 213 Route Calls to PSTN 525 nen san reen heel en anret hed 12 5 3 Gal PO AU CS 92 Er E E E 13 5 3 1 PSTN Pass TAO UAH czar NE EET KERNE E RaR E 14 5 4 EO A E E 14 5 5 Status LIONI IACI AIO W armor nesae deseecsnateaeeeeaeasesene 14 6 CONFIGURATION GUIDE sisiccsccecccecciscececetesscstessceestersxssebiccensceciceesseceisindeweseeectccvons 15 6 1 Configuring Unicorn 3112 using Web Browse ccccsseeeeeeeeeeeeeeeeeees 15 6 1 1 Accessing the Web Configuration cccccccccccscsseeeeeeeeeeeeeseeeeeesaaees 15 6 1 2 Programming Unicorn 3112 via the LAN Polt ccccsseeeeeeeeeeeeeees 16 6 1 3 Programming Unicorn 3112 via the WAN Polt cccsseeeeeeeeeeeeees 16 6 1 4 User Programming and Configuration ccccccsseeceeeeeeseeeeeeeeeeeees 17 ed TAS SV OS erie creer oases EE E E E EE 17 6 16 End User SENSE esenee EE AEREE a 17 BET Device SIGS score REEE 17 6 1 6 2 Basic Options vesecaiszedcagackeestemnsecdannondsnsemsepdatddereesiennagadiveteestenseadie 18 616o S
5. INVITE Send 200 OK Until FXO Has Detected Polarity Reversal FXO Pick Up Incoming Call After Receive 200 OK Form Server Special Feature Caller ID Minimum RX Level dB Caller ID Scheme Caller ID Transport Type Volume Amplification Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY As a Callee select UAC to use caller or proxy server as the refresher or UAS to use the device as the refresher Default is UAC Session Timer can be refreshed using INVITE method or UPDATE method Select Yes to use INVITE method to refresh the session timer Default is NO Default No Check with your PSTN carrier before set to Yes Default No Choose the selection to meet some special requirements from Soft Switch vendors Default is standard An adjustable value for the Caller ID signal to help this device to recognize Caller ID from different networks 50 OdB Default 30dB select caller ID to suit standard of different area According to customer s choice CID information will be transferred from PSTN network to VoIP network using following rules 1 via SIP from PSTN CID is in the SIP From field 2 via P Asserted Identity SIP From field uses the pre configured account user Id PSTN CID is in the P Asserted ldentity field 3 Send anonymous SIP From field uses anonymous PSTN CID is put in the P Asserted ldentity field 4 Disable PSTN CID will not be sent SIP From field uses the pre configured accou
6. Option E Mode If user selects Dynamic IP Mode the device will retrieve all IP address information from DHCP server automatically when user ERED ee en een eee nr _feboots thedevice The current WAN IP address is announced MP Address IP 02 Enter 12 digit new IP address if in Static IP address a EA LL g FO ee E Subnet IP address Same as Menu option 02 0000 Ui Gateway IP address Same as Menu option 02 DNS Server IP 05 Same as Menu option 02 meeen z address S E Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 7 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY 0 oo MAC Address Announces the Mac address of the unit Enter 9 to go to the next selection in the list PCMU PCMA 07 Preferred Vocoder G 726 G 723 Su Se re D SE ee EEN ERE Enter 9 to toggle between enable and 12 WAN Port Web Access gt ee i o reer disable Firmware Server IP Announces current Firmware Server IP 13 a Address address Enter 12 digit new IP address 44 Configuration Server IP Announces current Config Server Path IP Address address Enter 12 digit new IP address Upgrade protocol for firmware and 15 Upgrade Protocol configuration update EELISTE EE Rarer Enter 9 to toggle between TFTP and RTTP we Firmware Version Firmware version information i Firmware upgrade mode E
7. Unicorn 3112 User Manual Page 9 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY 5 2 6 Bellcore Style 3 way Conference Bellcore style 3 way conference is also supported To do this user needs to enable Use Bell style 3 way Conference in FXS web configuration Assuming that call party A and B are in conversation A wants to bring C in a conference 1 A presses FLASH on the analog phone or Hook Flash for old model phones to get a dial tone 2 A dials C s number then or wait for 4 seconds 3 If C answers the call then A press flash to bring B C in the conference 4 If C does not answer the call A can press flash back to talk to B 5 2 7 Direct IP to IP Calls Direct IP calling allows two parties that is a FXS Port with an analog phone and another VoIP Device to talk to each other in an ad hoc fashion without a SIP proxy Elements necessary to completing a Direct IP Call 1 Both Unicorn3112 and other VoIP Device have public IP addresses or 2 Both Unicorn3112 and other VoIP Device are on the same LAN using private IP addresses or 3 Both Unicorn3112 and other VolP Device can be connected through a router using public or private IP addresses with necessary port forwarding or DMZ Unicorn3112 supports two ways to make Direct IP Calling Using IVR 1 Pick up the analog phone then access the voice menu prompt by dial 2 Dial 47 to access the direct IP call menu 3 Enter the IP
8. assuming that Use as Dial Key is set to YES during web configuration of your Unicorn 3112 Other functions available during the call are call waiting flash call transfer and call forward Your SIP gatekeeper proxy server needs to support these features in order for them to work 5 2 2 Call Hold While in conversation pressing the FLASH button on the attached phone will put the remote end on hold Pressing the FLASH button again will release the previously Hold party and the bi directional media will resume 5 2 3 Call Waiting lf call waiting feature is enabled while the user is in a conversation he will hear a special stutter tone if there is another incoming call User can press the flash button to put the current call party on hold and switch to the other call Pressing flash button toggles between two active calls 5 2 4 3 way Conferencing Unicorn3112 supports 3 way conference in two styles star code style or Bellcore style 5 2 5 Star Code Style 3 way Conference Assuming that call party A and B are in conversation A wants to bring C in a conference 1 A presses FLASH on the analog phone or Hook Flash for old model phones to get a dial tone 2 A dials 23 then C s number then ff or wait for 4 seconds 3 If C answers the call then A press flash to bring B C in the conference 4 If C does not answer the call A can press flash back to talk to B Hanlong Technology Co Ltd
9. choosing STUN and a STUN server is also specified then the Unicorn 2101 will behave according to the STUN client specification Under this mode the embedded STUN client inside the Unicorn 2101 will attempt to detect if and what type of firewall NAT it is sitting behind through communication with the specified STUN server If the detected NAT is a Full Cone Restricted Cone or a Port Restricted Cone the Unicorn 2101 will attempt to use its mapped public IP address and port in all its SIP and SDP messages If choosing STUN with no specified STUN server the Unicorn 2101 will periodically every 20 seconds or so send a blank UDP packet with no payload data to the SIP server to keep the hole on the NAT open lf choosing UPNP the embedded UPNP client inside the Unicorn 2101 will attempt to mapping ports with the router by upnp protocol SIP service subscriber s User ID SIP service subscriber s Authenticate ID Can be identical to or different from SIP User ID SIP service subscriber s account password SIP service subscriber s name which will be used for Caller ID display Default is No If set to Yes the client will use DNS SRV for server lookup Unicorn 3112 User Manual Page 29 of 39 Firmware 1 0 0 46 Last Updated User ID is phone number SIP Registration Unregister On Reboot Register Expiration Outgoing Call without Registration Local SIP port Local RTP port Use random port Refer To Use Target Contact DTMF P
10. tone This setting can be configured to suit the telephone company s standard in different country If set to Yes the Polarity Reversal is used as the disconnect signal If set Yes the device terminate the call when Silence timer expire Silence timer value default is 60 minutes You have two options If choose Power off mode the fxs will connect to the PSTN only when power off lf choose auto mode device will connect to PSTN when VOIP is not working Default is 500ms This needs to be equal to or greater than the Current Disconnect threshold setting Once the threshold is reached the gateway can dial out This parameter should only be used if there are PSTN line detection issues Default value is 11dB Digit length and Dial Pause are port digit dialing configurations FXO needs to dial out digits for VOIP to PSTN 1 stage calls and unconditional call forward to PSTN and route to PSTN Digit Length is the play time for each digit Note In order to receive the caller ID information the delay should be set to a value larger than the delay required to complete the PSTN caller ID delivery Please note that the value will be multiplied by 10ms Dial pause is the time between 2 digits for the same scenario as explained above Unicorn 3112 User Manual Page 35 of 39 Firmware 1 0 0 46 Last Updated Ez HANLON G TECHNOLOGY Please note that the value will be multiplied by 10ms This configuration is applicable for VoIP t
11. 008 This parameter when set to YES will force random generation of both the local SIP and RTP ports This is usually necessary when multiple Unicorn 2101 are behind the same NAT Default is NO If set to YES then for Attended Transfer the Refer To header uses the transferred target s Contact header information Sets the payload type for DIMF using RFC2833 This parameter specifies the mechanism to transmit DTMF digit in audio which means DTMF is combined in audio signal not very reliable with low bit rate codec Default is YES This parameter specifies the mechanism to transmit DTMF digit via RTP RFC2833 Default YES Unicorn 3112 User Manual Page 30 of 39 Firmware 1 0 0 46 Last Updated DTMF via SIP INFO Proxy Require Use NAT IP Preferred Vocoder Voice Frames per TX G723 Rate SRTP Mode Optional VAD Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY This parameter specifies the mechanism to transmit DTMF digit via SIP INFO Default is NO SIP Extension to notify SIP server that the unit is behind the NAT Firewall NAT IP address used in SIP SDP message Default is blank The Unicorn2101 supports up to 5 different Vocoder types including G 711 A U law G 726 Supports bit rates 32K G 723 1 G 729A B The user can configure Vocoders in a preference list that will be included with the same preference order in SDP message The first Vocoder is entered by choosing the appropriate option in Cho
12. A wants to Attend Transfer party B to party C Party A presses FLASH on the analog phone or Hook Flash for old model phones to get a dial tone Party A then dials party C s number then or wait for 4 seconds Party A and party C now are in conversation Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 11 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 Party A can hang Note When Attended Transfer failed and if party A hangs up the Unicorn 3112 will ring party A again to remind party A that party B is still on the call by pressing FLASH or Hook again will restore the conversation between party A and party B 5 2 10 Send and Receive PSTN Calls Users can send and receive calls from PSTN To receive PSTN calls simply take the phone off hook when the analog phone rings To makea PSTN call first press 00 or your own PSTN Access Code to get the PSTN line dial tone and dial the PSTN number 9 2 11 VoIP to PSTN Calls To make a VoIP to PSTN call users need to dial the FXO SIP account phone number first A ring tone is played once followed by a dial tone At this time users can dial a PSTN telephone number or a mobile telephone number then or wait for 4 seconds The call will be established afterwards If no PSTN number is entered after the dial tone Unicorn 3112 will hang up automatically in 10 seconds In the web configuration page if the Route to PSTN field is configured the second stage dialing is elim
13. ACT Email Support mail hanlongtek com Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 39 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012
14. NVITE message will be set to anonymous essentially blocking the Caller ID from displaying The session timer extension enables SIP sessions to be periodically refreshed via a re INVITE request Once the session interval expires if there is no refresh via a re INVITE message the session will be terminated Session Expiration is the time in seconds at which the session is considered timed out if no successful session refresh transaction occurs beforehand The default value is 180 seconds Default is 180 seconds The minimum session expiration in seconds Default is 90 seconds lf selecting Yes the device will use session timer when it makes outbound calls if remote party supports session timer Default is NO If selecting Yes the phone will use session timer when it receives inbound calls with session timer request Default is NO If selecting Yes the device will use session timer even if the remote party does not support this feature Selecting No will allow the device to enable session timer only when the remote party support this feature To turn off Session Timer select No for Caller Request Timer Callee Request Timer and Force Timer Default is NO As a Caller select UAC to use the device as the refresher or UAS to use the Callee or proxy server as the refresher Default is Omit Unicorn 3112 User Manual Page 33 of 39 Firmware 1 0 0 46 Last Updated UAS Specify Refresher Force
15. UPE OPIO ac O Ei 20 6 1 6 4 FXS Port SettingS ccccccccsseseecccccseecescsseeeeccseeeeecceeeeecceeees 22 6 165 FXO Pon Senge sesaieseroiroinno roue rar ere NE EET 29 Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 2 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 aa 1 TECHNOLOGY 6 1 7 Saving the Configuration Changes cccccccssseceseeseeeeseeeeeeeseeneeeeens 36 6 1 8 Rebooting the Unicorn 3112 cc cceeeeccsseeeeceeeeeceeseeseeeeeseeseessaeeeeas 37 6 2 Configuring Unicorn 3112 via Voice Prompt ccceeceeeseeeeeeeeeeeeeeeaeeees 37 6 2 1 DHCP Mode aerer e e ee EEE EET aeiaai E 37 622 SUT IP MOOG erpinen innr enian nE EAEE NEEESE E EEEE oF 6 3 Configuration through a Central Server ccccceccccccseeeeeeseeeeeeeaeeeeeesaeeeees 37 SOFTWARE UPGRADE 2222 HEEL nn nnmnnn EEN ENE 38 RESTORE FACTORY DEFAULT SETTINGG c csssseeeesccsssseeeeecessseeeeseeeeseeees 38 TECHNICAL SUPPORT CONTACT ssceceeeccsssseeeeseeessseeeseeeenseeesecoanseeesseonaaes 39 WELCOME Unicorn 3112 is an all in one VoIP integrated access device that features superb audio quality rich functionalities high level of integration compactness and ultra atfordability The Unicorn 3112 is fully compatible with SIP industry standard and can interoperate with many other SIP compliant devices and software on the market Special compatibility features include Zs Nortel MCS Standard SIP
16. User Manual Unicorn 3112 Analog Telephone Adaptor a crs Hanlong Technology Co Ltd http www hanlongtek com TECHNOLOGY k WELCOME erm re ae nS ee ee ee eee eee ee ree eer eer 3 2 WHAT IS IN THE PACKAGE 2 ccccccsnssseeececcnnseesceecnnesseeeecnnnsseseeeennsssseeesanees 3 3 PRODUCT OVERVIEW 2 22202ccccucu cee ssscceeecescetencseseseeeececeatasieeeseanseitececstexkdeesedexssaceesenn 4 3 1 KOV FOTOS ornare cee tec gate cme E EEG 4 3 2 Hardware specification ccccsecccseecccseeceeeecneeeeeeeeeseeeeseeeeseeeeseeeeseeeeseneensees 4 4 INSTALEATIONS een ee en eee ee ee ee eee eee 5 4 1 O a E E E E E N eae 6 5 BASIC OPERATIONS rece te snd sc canes 2c ects capes cece ae meee 7 5 1 Get Familiar With Voice cccccceecccceeeccceseceeeeeeeeaeecesaueceeseeeessueeeesaeeesseeeees 7 52 Make Phone call ciscwserisunisticietmnicisctnndntecictisiemnietneadnliclottidauiesiemanaatcGuidaueseacsnatintincoiatdmotenesiie 9 5 2 1 Calling Phone or Extension NUMDEIS cccccseeeeeceeeeeeeeeeeeeesaeees 9 522 Gall ONG aenieei EE EE 9 523 Call WANG sassone e SEENE EEA 9 5 2 4 3 way CONPErENCING ccccccccseecceeeeeceeeceeeceeeseeceeeseeueeeeauaeeeesuaeeeessnaes 9 5 2 5 Star Code Style 3 way Conference ccccccccseeceeseeeeseeseeeseeeeeeaeeeeaees 9 5 2 6 Bellcore Style 3 way COnference ccccccccceseeeeeeeeeeeeseeeeseeseeeeeeeens 10 5 2 7 Direct IP to IP Calls
17. address using format ex 192 168 0 160 after the dial tone Using Star Code 1 Pick up the analog phone then dial 47 2 Enter the target IP address using same format as above Note NO dial tone will be played between step 1 and 2 Destination ports can be specified by using number kkk 66 37 encoding for followed by the port Examples a If the target IP address is 192 168 0 160 the dialing convention is 47 or Voice Prompt with option 47 then 192 168 0 160 followed by pressing the key if it is configured as a send key or wait 4 seconds In this case the default destination port 5060 is used if no port is specified b If the target IP address port is 192 168 1 20 5062 then the dialing convention would be 47 or Voice Prompt with option 47 then 192 168 0 160 5062 followed by pressing the P key if it is configured as a send key or wait for 4 seconds NOTE When completing direct IP call the Use Random Port should set to NO Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 10 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY 5 2 8 Blind Transfer Assuming that call party A and party B are talking to each other on the phone Party A wants to transfer party B to party C Party A presses FLASH on the analog phone or Hook Flash for old model phones to get a dial tone e Then party A dials 87 then dials party C s number and then or wait for 4
18. arameter located on the FXS Port Configuration page lf call volume is too low when using the FXS port ie the ATA is at user site adjust volume using the Rx Gain Level parameter under the FXS Port Configuration page If voice volume is too low at the other end user may increase the far end volume using the Tx Gain Level parameter under the FXS Port Configuration page This function lets you configure ring tone cadence preferences User has 10 choices The configuration completed in Distinctive Ring Tones block in the same page applies to ring tones cadences configured here Unicorn 3112 User Manual Page 28 of 39 Firmware 1 0 0 46 Last Updated TECHNOLOGY 6 1 6 5 FXO Port Settings Setting options Account Active SIP Server Outbound Proxy SIP transport Optional NAT Traversal SIP User ID Authenticate ID Authenticate Password Name Use DNS SRV Hanlong Technology Co Ltd 1 19 2012 FXS PORT Definitions Set to the YES the account can be available SIP Server s URI or IP address SIP Outbound Proxy Server s URI or IP address Select transport between UDP and TLS default is UDP This parameter defines whether the Unicorn 2101 NAT traversal mechanism will be activated or not lf Choosing No nothing to do lf Choosing No but send keep alive the Unicorn 2101 will periodically every 20 seconds or so send a blank UDP packet with no payload data to the SIP server to keep the hole on the NAT open lf
19. ate for G723 vocoder By default 6 3kbps rate is chosen Enable SRTP mode based on selection Default is No Default is No VAD allows detecting the absence of audio and conserve bandwidth by preventing the transmission of silent packets over the network Default is No When set to Yes the device will change the destination to send RTP packets to the source IP address and port of the inbound RTP packet last received by the device Default is T 30 Fax Pass Through or T 38 Auto Detect FoIP Default is Callee This decides whether Caller or Callee sends out the re INVITE for T 38 or Fax Pass Through Select either Fixed or Adaptive based on network conditions Select Low Medium or High based on network conditions Caller ID must be configured Select a Distinctive Ring Tone 1 through 3 for a particular Caller ID The device will ONLY use selected ring tones for particular Caller IDs For all other calls the device will use System Ring Tone When selected and no Caller ID is configured the selected ring tone will be used for all incoming calls Conference mode default option is No If set to yes the feature code for coference 23 would be disabled Default is NO User can use star codes to enable disable call waiting Default is NO This is to disable the stutter call waiting tone when a call waiting call arrived An incoming call will stop ringing when not picked up given a specific period of time Default is 4 s
20. ayload Type DTMF in Audio DTMF via RFC2833 Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY lf the Unicorn 2101 has an assigned PSTN telephone number this field should be set to Yes Otherwise set it to No If Yes is set a user phone parameter will be attached to the From header in SIP request This parameter controls whether the Unicorn 2101 needs to send REGISTER messages to the proxy server The default setting is Yes Default is No If set to Yes the SIP user will be unregistered on reboot This parameter allows the user to specify the time frequency in minutes the Unicorn 2101refreshes its registration with the specified registrar The default interval is 6 minutes The maximum interval is 65535 minutes about 45 days Default is No If set to Yes user can place outgoing calls even when not registered if allowed by ITSP but is unable to receive incoming calls This parameter defines the local SIP port the Unicorn 2101 will listen and transmit The default value for FXS port is 5060 The default value for FXO port is 5062 This parameter defines the local RTP RTCP port pair the Unicorn 2101 will listen and transmit It is the base RTP port for channel 0 When configured channel 0 will use this port value for RTP and the port value 1 for its RTCP channel 1 will use port value 2 for RTP and port value 3 for its RTCP The default value for FXS port is 5004 The default value for FXO port is 5
21. ber with leading digit 2 and 10 digit numbers of leading digit 1 and leading exchange number between 2 and 9 if leading digit is 2 replace leading digit 2 with 011 before dialing 3 Default Outgoing x Example of a simple dial plan used in a Home Office in the US 1900x lt 1617 gt 2 9 xxxxxx 1 2 9 xx 2 9 xxxxxx 011 2 9 x 3469 11 Explanation of example rule reading from left to right 1900x prevents dialing any number started with 1900 lt 1617 gt 2 9 xxxxxx allows dialing to local area code 617 numbers by dialing 7 numbers and 1617 area code will be added automatically Unicorn 3112 User Manual Page 32 of 39 Firmware 1 0 0 46 Last Updated Send Anonymous Session Expiration Min SE Caller Request Timer Callee Request Timer Force Timer UAC Specify Refresher Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY 1 2 9 xx 2 9 xxxxxx allows dialing to any US Canada Number with 11 digits length 011 2 9 x allows international calls starting with 011 3469 11 allow dialing special and emergency numbers 311 411 611 and 911 Note In some cases user wishes to dial strings such as 123 to activate voice mail or other application provided by service provider In this case should be predefined inside dial plan feature and the Dial Plan should be x More information can be availabled at Dail Plan Notes lf this parameter is set to Yes the From header in outgoing I
22. calls by pressing 00 Without pressing 00 all your calls will be VoIP You can also receive PSTN calls and VolP calls The following photo illustrates the Interconnection Diagram of the of a Unicorn 3112 Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 5 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 Ez HANLON GG TECHNOLOGY Internet Network Analog Phone FXO FXS PSTN Following are the steps to install a Unicorn 3112 e Connect a standard touch tone analog telephone to the Phone port Insert a standard RJ11 telephone cable included with package into the Line port and connect the other end of the telephone cable to a wall jack Connect a PC to the LAN port of Unicorn 3112 Ethernet cable is included with package Insert another Ethernet cable into the WAN port of Unicorn 3112 and connect the other end of the Ethernet cable to an uplink port a router switch hub modem etc Insert the powers supply included with package into the Unicorn 3112 and connect it to a power outlet 4 1 Safety The Unicorn 3112 is compliant with various safety standards including FCC CE and C Tick Its power adaptor is compliant with UL standard The Unicorn 3112 should only operate with the universal power adaptor provided in the package Warning Please do not use a different power adapter Using other power adapter may damage the Unicorn 3112 and will void the manufacturer warranty Hanlon
23. e Alternatively you can reboot by unplugging the power supply of the Unicorn 3112 and then powering it on again If your Unicorn 3112 ever becomes stuck or un responsive you can unplug the power supply to reboot it Frequent rebooting by unplugging the power supply is not recommended and should not be necessary 6 2 Configuring Unicorn 3112 via Voice Prompt 6 2 1 DHCP Mode Follow section 5 1 with voice menu option 01 to enable Unicorn 3112 to use DHCP 6 2 2 Static IP Mode Follow section 5 1 with voice menu option 01 to enable Unicorn 3112 to use STATIC IP mode then use option 02 03 04 to set up Unicorn 3112 s IP Subnet Mask Gateway respectively 6 3 Configuration through a Central Server Unicorn 3112 devices can be automatically configured from a central provisioning system When Unicorn 3112 boots up it will send TFTP or HTTP request to download configuration files There are two configuration files one is cfg txt and the other is cfg001fc1xxxxxx where O01 fc1xxxxxx is the MAC address of the Unicorn 3112 For more information regarding configuration file format please refer to the related technical documentation The configuration file can be downloaded via TFTP or HTTP from the central server A service provider or an enterprise with large deployment of Unicorn 3112s can easily manage the configuration and service provisioning of individual devices remotely and automatically from a central serv
24. e of audio and conserve bandwidth by preventing the Unicorn 3112 User Manual Page 31 of 39 Firmware 1 0 0 46 Last Updated Symmetric RTP Fax Mode Fax Tone Detection Mode Jitter Buffer Type Jitter Buffer Length Dial Plan Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY transmission of silent packets over the network Default is No When set to Yes the device will change the destination to send RTP packets to the source IP address and port of the inbound RTP packet last received by the device Default is T 30 Fax Pass Through or T 38 Auto Detect FoIP Default is Callee This decides whether Caller or Callee sends out the re INVITE for T 38 or Fax Pass Through Select either Fixed or Adaptive based on network conditions Select Low Medium or High based on network conditions Dial Plan Rules 1 Accept Digits 1 2 3 4 5 6 7 8 9 0 A a B b C c D d 2 Grammar x any digit from 0 9 a XX at least 2 digits number b xx at least 2 digits number c exclude d 3 5 any digit of 3 4 or 5 e 147 any digit 1 4 or 7 f lt 2 011 gt replace digit 2 with 011 when dialing Example 1 869 11 1617xxxxxxx Allow 311 611 911 and any 10 digit numbers of leading digits 1617 Example 2 1900x lt 1617 gt xxxxxxx Block any number of leading digits 1900 and add prefix 1617 for any dialed 7 digit numbers Example 3 1xxx 2 9 xxxxxx lt 2 011 gt x Allow any length of num
25. econds Unicorn 3112 User Manual Firmware 1 0 0 46 Page 25 of 39 Last Updated Use as Dial Key Dial Plan Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY This parameter allows users to configure the key to be used as the Send or Dial key If set to Yes pressing this key will immediately trigger the sending of dialed string collected so far In this case this key is essentially equivalent to the Re Dial key If set to No this key will then be included as part of the dial string to be sent out Dial Plan Rules Accept Digits 1 2 3 4 5 6 7 8 9 0 A a B b C c D d Grammar x any digit from 0 9 XX at least 2 digits number XX at least 2 digits number exclude 8 5 any digit of 3 4 or 5 e 147 any digit 1 4 or 7 f lt 2 011 gt replace digit 2 with 011 when dialing Example 1 869 11 161 7xxxxxxx Allow 311 611 911 and any 10 digit numbers of leading digits 1617 Example 2 1900x lt 1617 gt xxxxxxx Block any number of leading digits 1900 and add prefix 1617 for any dialed 7 digit numbers Example 3 1xxx 2 9 xxxxxx lt 2 011 gt x Allow any length of number with leading digit 2 and 10 digit numbers of leading digit 1 and leading exchange number between 2 and 9 if leading digit is 2 replace leading digit 2 with 011 before dialing 3 Default Outgoing x Example of a simple dial plan used in a Home Office in the US 1900x
26. er The central provisioning system uses enhanced NAT friendly TFTP or HTTP thus no NAT issues and other communication protocols to communicate with each individual Unicorn 3112 for firmware upgrade etc Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 37 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY 7 SOFTWARE UPGRADE To upgrade software Unicorn 3112 can be configured with a TFTP server where the new code image is located The TF TP upgrade can work in either static IP or DHCP mode using private or public IP address It is recommended to set the TFTP server address in either a public IP address or on the same LAN with the Unicorn 3112 There are two ways to set up the TFTP server to upgrade the firmware namely through voice menu prompt or via the Unicorn 3112 s Web configuration interface To configure the TFTP server via voice prompt follow section 5 1 with option 06 once set up the TFTP IP address power cycle the ATA the firmware will be fetched once the ATA boots up To configure the TFTP server via the Web configuration interface open up your browser to point at the IP address of the Unicorn 3112 Input the admin password to enter the configuration screen From there enter the TFTP server address in the designated field towards the bottom of the configuration screen Once the TFTP server is configured please power cycle the Unicorn 3112 TFTP process may take as long as 1 to 2 minutes over the Inter
27. erence ssssssss i lt iCO 870 Blind Transfer 0 Block Caller ID for all subsequent calls LL o Send Caller ID for all subsequent calls i 67 OOO Block Caller ID per cal D Send Caller ID per cal i 50 OOOO Disable Call Waiting for all subsequent calls 00 f 51 Enable Call Waiting for all subsequent calls 000 20 Disable Gat Wale Perea CC 474 Enable Call Waiting Per Call _ Unconditional Call Forward 8 72 To use this feature dial 72 and get the dial tone Then dial the forward number and for a dial tone then hang up Cancel Unconditional Call Forward 173 To cancel Unconditional Call Forward dial 73 and get the dial tone oo nen hang up Busy Call Forward 90 To use this feature dial 90 and get the dial tone Then dial the forward ae number and for a dial tone then hang up _ ee ee ene Cancel Busy Call Forward 91 To cancel Busy Call Forward dial 91 and get the dial tone then hang ee Res acre eee eR A E Ne ee E Delayed Call Forward l 92 To use this feature dial 92 and get the dial tone Dial the forward ee number and for a dial tone and then hang up E Cancel Delayed Call Forward l TEA To cancel this feature dial 93 get the dial tone and then hang up Call waiting indication Flash Hook When in conversation without an incoming call this actio
28. ess This field shows IP address of device Product Model This product model is Unicorn2101 Software Version Information of software System Uptime Show system uptime since last reboot Indicates where the PPPoE connection is up if the PPPoE Link Up NAT Uicorn2101 is connected to the DSL modem Indicate the NAT type behind which the device is when the stun feature Is defined Indicate the current status of the device such as hook on off registion registered unregistered etc Port Status 6 1 6 2 Basic Options Setting options Web Port IP Address Time Zone Allow DHCP Option 2 to override Time Zone setting Daylight Savings Time Hanlong Technology Co Ltd 1 19 2012 BASIC OPTIONS Setting Definitions The default is 80 There are 3 modes under which the Unicorn 2101 can operate lf DHCP mode is enabled then all the field values for the Static IP mode are not used even though they are still saved in the chipset s memory The Unicorn 2101 will acquire its IP address from the first DHCP server it discovers from the office home network it is connected to To use the PPPoE feature the PPPoE account settings need to be set The Unicorn 2101 will attempt to establish a PPPoE session if any of the PPPoE fields have been entered with data If Static IP mode is enabled then the IP address Subnet Mask Default Router IP address DNS Server 1 primary DNS Server 2 secondary fields will need to be con
29. fault is Omit As a Callee select UAC to use caller or proxy server as Unicorn 3112 User Manual Firmware 1 0 0 46 Page 27 of 39 Last Updated Force INVITE Special Feature FXS impedance Caller ID Scheme Onhook Voltage Polarity Reversal Hook Flash Timing Volume Amplification Ring Tones Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY the refresher or UAS to use the device as the refresher Default is UAC Session Timer can be refreshed using INVITE method or UPDATE method Select Yes to use INVITE method to refresh the session timer Default is NO Choose the selection to meet some special requirements from Soft Switch vendors Default is standard Select the impedance of analog telephone connected to phone port select caller ID to suit standard of different area Select onhook voltage to suit standard of different area or PBX Select Polarity Reversal to adapt some call charge billing system Default is NO Time period when the cradle is pressed Hook Flash to simulate FLASH To prevent unwanted activation of the Flash Hold and automatic phone ring back adjust this time value Voice path volume adjustment Rx is a gain level for signals transmitted by FXS Tx is a gain level for signals received by FXS Default OdB for both parameters Loudest volume 6dB Lowest volume 6dB User can adjust volume of call on either end using the Rx Gain Level parameter and the Tx Gain Level p
30. figured by the user These fields are reset to zero by default This parameter controls how the displayed date time will be adjusted according to the specified time zone If set yes and under DHCP mode the device will try to get option 2 from DHCP configure and overwrite Time Zone This parameter controls whether the displayed time will Unicorn 3112 User Manual Page 18 of 39 Firmware 1 0 0 46 Last Updated Device Mode LAN Subnet Mask LAN DHCP Base IP DHCP IP Lease Time Port Map End User Password Reply to ICMP on WAN Port WAN Side Http Access Number of Rings PSTN Ring Thru FXS PSTN Ring Thru Delay sec PSTN Access Code PIN for PSTN Calls PIN for VOIP Calls Unconditional Call Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY be daylight savings time or not If set to Yes then the displayed time will be 1 hour ahead of normal time This parameter controls whether the device is working in NAT router mode or Bridge mode Need save the setting and reboot the device before the setting start to work Sets the LAN subnet mask Default value is 255 255 255 0 Base IP for the LAN port which functions as a Gateway for the subnet Default value is 192 168 22 1 Value is set in units of hours Default value is 120 hrs 5 Days The time IP address is assigned to the LAN clients Forwards a matching TCP UDP port to a specific LAN IP address with a specific TCP UDP port This contains the password to acces
31. g Technology Co Ltd Unicorn 3112 User Manual Page 6 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY Caution Changes or modifications to this product not expressly approved by Hanlong Technology or operation of this product in any way other than as detailed by this User Manual could void your manufacturer warranty Information in this document is subject to change without notice No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of Hanlong Technology 5 BASIC OPERATIONS 5 1 Get Familiar with Voice Unicorn 3112 has stored a voice prompt menu for quick access to settings and simple configuration You can enter this voice prompt menu as follows Pick up the receiver or press the Handsfree button of the analog telephone and press A voice will say Enter the new option At this point you can select from the following menu voice prompt options to begin using the Unicorn 3112 Voice Will Say the F ollowing Enter for the next menu option Enter 4 to return to the main menu Enter 01 07 12 17 47 86 or 99 Menu lee rr option en Enter 9 to toggle the selection If user selects Static IP Mode user need configure all the IP address information DHCP Mode Static IP gt through menu 02 to 05 Main Menu i Enter a Menu
32. gy Co Ltd 1 19 2012 TECHNOLOGY DTMF digit via RTP RFC2833 Default YES This parameter specifies the mechanism to transmit DTMF digit via SIP INFO Default is NO This parameter allows users to control whether to send an SIP NOTIFY message indicating the Flash event or just to switch to the voice channel when users press the Flash key Default is No If set to Yes Call Forwarding amp Do Not Disturb are supported locally This parameter allows users to configure a User ID or extension number to be automatically dialed upon offhook Please note that only the user part of a SIP address needs to be entered here The Unicorn 2101 will automatically append the and the host portion of the corresponding SIP address SIP Extension to notify SIP server that the unit is behind the NAT Firewall NAT IP address used in SIP SDP message Default is blank The Unicorn2101 supports up to 5 different Vocoder types including G 711 A U law G 726 Supports bit rates 32k G 723 1 G 729A B The user can configure Vocoders in a preference list that will be included with the same preference order in SDP message The first Vocoder is entered by choosing the appropriate option in Choice 1 The last Vocoder is entered by choosing the appropriate option in Choice 6 This field contains the number of voice frames to be transmitted in a single packet When setting this value the user should be aware of the requested packet ti
33. ice 1 The last Vocoder is entered by choosing the appropriate option in Choice 6 This field contains the number of voice frames to be transmitted in a single packet When setting this value the user should be aware of the requested packet time used in SDP message as a result of configuring this parameter This parameter is associated with the first vocoder in the above vocoder Preference List or the actual used payload type negotiated between the 2 conversation parties at run time e g if the first vocoder is configured as G723 and the Voice Frames per TX is set to be 2 then the ptime value in the SDP message of an INVITE request will be 60ms because each G723 voice frame contains 30ms of audio Similarly if this field is set to be 2 and if the first vocoder chosen is G729 or G711 or G726 then the ptime value in the SDP message of an INVITE request will be 20ms If the configured voice frames per TX exceeds the maximum allowed value the Unicorn 2002 will use and save the maximum allowed value for the corresponding first vocoder choice The maximum value for PCM is 10 x10ms frames for G726 it is 20 x10ms frames for G 723 it is 32 x30ms frames for G729 G728 64 x10ms and 64 x2 5ms frames respectively This defines the encoding rate for G723 vocoder By default 6 3kbps rate is chosen Enable SRTP mode based on selection Default is No Default is No VAD allows detecting the absenc
34. inated That is after users dial the FXO SIP account number the PSTN number will be called automatically 9 2 12 PSTN to VoIP Calls To make a PSTN to VoIP call PSTN callers need to originate a call to the FXO port telephone number first If no one answers the FXS phone after 4 default value can be configured ring tones a dial tone is played At this time users can dial a VoIP telephone number then or wait for 4 seconds The call will be established afterwards If no VoIP number is entered after the dial tone Unicorn 3112 will hang up automatically in 10 seconds In the web configuration page if the Route to VoIP field is configured the second stage dialing is eliminated That is after users dial the FXO port telephone number the VoIP number will be called automatically 5 2 13 Route Calls to PSTN lf configured certain calls will be routed to PSTN line automatically This call feature is especially useful for emergency calls or local telephone calls To use this feature users need to specify a prefix or a telephone number in the Route to PSTN field in the web Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 12 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY configuration page If the dialed digits match one of the specified prefix outbound calls will be routed to PSTN port 5 3 Call Features Call Features Tables Following table shows the call features of Unicorn 3112 723 3 way conf
35. lf this parameter is set to Yes the configuration update via keypad is disabled Default is NO The IP address or URL of System log server This feature is especially useful for the ITSP Internet Telephone Service Provider Default is blank the feature is useful for the Internet Telephone Service Provider User can download configuration from the web page and save to configuration file Using these settings users can configure tone frequencies and cadence according to their preference By default they are set to North American frequencies Configure these settings with known values to avoid uncomfortable high pitch sounds ON is the period of ringing On time in ms while OFF is the period of silence In order to set a continuous tone OFF should be zero Otherwise it will ring ON ms and a pause of OFF ms and then repeat the pattern Example configuration for N A Dialtone 11 350 13 f2 440 13 c 0 0 Syntax f1 freq vol f2 freq vol c 0n1 off1 on2 off2 on3 off3 Note freq 0 4000HZz vol 30 OdBm User can import the TLS Certification Unicorn 3112 User Manual Firmware 1 0 0 46 Page 21 of 39 Last Updated Restore Configuration TECHNOLOGY User can restore the before configuration from the configuration file saved at local pc 6 1 6 4 FXS Port Settings Setting options Account Active SIP Server Outbound Proxy SIP transport Optional NAT Traversal SIP User ID Authenticate ID Au
36. lowing screen shot of the Unicorn 3112 basic option page Reply to ICMP on WAN port O No Yes Unitwill not respond to PING from WAN side if set to No WAN side http access O No ves WAN side access to http server will be rejected if set to No P HEE O HE o Number of rings for a PSTN incoming call to FXO port before FXO port picks up default 4 ON ilf setto yes PSTN Ring Thru FXS Yes Default Yes all incoming PSTN calls will ring the FXS port after the Ring Thru Delay PSTN Ring Thru Delay sec 4 4 10 seconds Default 4 seconds PIN for PSTN Calls Enter digits to authorize calling PSTN numbers from VOIP no default PIN for VOIP Calls Enter digits to authorize calling VOIP terminals from PSTN no default PSTN access code key pattern to use PSTN line default is 00 Unconditional Call Forward to PSTN VOIP calls will be forwarded to the specified PSTN number Sip Destination UserID Sip Server Port fxo001 home xanadu hanlongtec cn 5060 Reboot Unconditional Call Forward to VOIP After enabling WAN access be sure that the WAN port of the Unicorn 3112 is connected to an uplink i e router hub switch etc Then get the WAN IP address of the Unicorn 3112 and selecting menu option 02 Then access the Unicorn 3112 via your web browser by entering the WAN IP address http Unicorn 3112 s IP Address Be sure that your PC is connected to the router hub switch directly or via the LAN
37. me used in SDP message as a result of configuring this parameter This parameter is associated with the first vocoder in the above vocoder Preference List or the actual used payload type negotiated between the 2 conversation parties at run time e g if the first vocoder is configured as G723 and the Voice Frames per TX is set to be 2 then the ptime value in the SDP message of an INVITE request will be 60ms because each G723 voice frame contains 30ms of audio Similarly if this field is set to be 2 and if the first vocoder chosen is G729 or G711 or Unicorn 3112 User Manual Page 24 of 39 Firmware 1 0 0 46 Last Updated G723 Rate SRTP Mode Optional VAD Symmetric RTP Fax Mode Fax Tone Detection Mode Jitter Buffer Type Jitter Buffer Length Distinctive Ring Tone Use Bell style 3 way Conference Disable Call Waiting Disable Call Waiting Tone Ring Timeout No Key Entry Timeout Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY G726 then the ptime value in the SDP message of an INVITE request will be 20ms If the configured voice frames per TX exceeds the maximum allowed value the Unicorn 2002 will use and save the maximum allowed value for the corresponding first vocoder choice The maximum value for PCM is 10 x10ms frames for G726 it is 20 x10ms frames for G723 it is 32 x30ms frames for G729 G728 64 x10ms and 64 x2 5ms frames respectively This defines the encoding r
38. n will switch to a new channel to make a new call Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 13 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY 5 3 1 PSTN Pass Through When Unicorn 3112 is out of power or loses registration or if the network connection is down the RJ 11 line jack on the side of Unicorn 3112 will function as a pass through connection for PSTN calls Users will be able to use the same analog phone for PSTN calls 5 4 FAX Unicorn3112 supports FAX in two modes T 38 Fax over IP and fax pass through T 38 is the preferred method because it is more reliable and works well in most network conditions If the service provider supports T 38 please use this method by selecting Fax mode to be T 38 If the service provider does not support T 38 pass through mode may be used To send or receive faxes in fax pass through mode users will need to select all the Preferred Codecs to be PCMU PCMA 5 5 Status Light Indicator ASAs Eana the bald 3112 button light pattern indication 1 second ON then 1 second OFF Indicates device software is running Run Light Fast blinking indicate the product in firmware upgrading or provision i Indicate status of the FXS Port on the back panel Busy ON Solid Green Phone Light Available OFF Fast blinking Ringing eee Slow blinking FXS LEDs indicates voicemail for that port I Indicate Status of the Line Port on the back panel
39. nd Provisioning 6 1 1 Accessing the Web Configuration The Unicorn 3112 configuration page can be accessed via the LAN or WAN port The GUI interface can be download at bellow http Awww hanlongtek com books 3112 gui rar This gui include bellow pages 1 SCREENSHOT OF DEVICE STATUS PAGE 2 SCREENSHOT OF BASIC OPTIONS PAGE 3 SCREENSHOT OF SUPPER OPTIONS PAGE 4 SCREENSHOT OF FXS PORT PAGE 5 SCREENSHOT OF FXO PORT PAGE Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 15 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 San HANLON G TECHNOLOGY 6 1 2 Programming Unicorn 3112 via the LAN Port To program Unicorn 3112 via the LAN port directly connect an Ethernet cable from your PC to the LAN port of the Unicorn 3112 After connecting the cable confirm that the green light of the LAN port is on If the green light is not on this means that your PC is not yet properly connected to the Unicorn 3112 via the LAN port For LAN port configuration use the following default IP address to access the device http 192 168 22 1 6 1 3 Programming Unicorn 3112 via the WAN Port The WAN port access for web configuration is disabled by default from the factory To access the web configuration menu from the WAN port you must first access the device via the device LAN port see instructions above Programming Unicorn 3112 via the LAN port and enable the Enable WAN Web Access option Please see the fol
40. nd ignore the Config Server Path Option 66 TFTP server name if you select Upgrade Via gt TFTP HTTP server name if you select Upgrade Via gt HTTP Option 128 TFPT Server IP address if you select Upgrade Via gt TFIP HTTP Server IP address if you select Upgrade Via gt HTTP Option 150 TFTP server address if you selectUpgrade Via gt T FTP HTTP server address if you select Upgrade Unicorn 3112 User Manual Page 20 of 39 Firmware 1 0 0 46 Last Updated Authenticate Conf File SNMP Service Enable SNMP Get Community SNMP Set Community SNMP Manager IP 1 SNMP Manager IP 2 SNMP Manager IP 3 SNMP Manager IP 4 NTP Server Allow DHCP Option 42 to override NTP server Lock Keypad Update Disable Voice Prompt Syslog Server Syslog Level Download Device Configuration Call Progress Tones Import TLS Certificate File Optional Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY Via gt HTTP configure file would be authenticated before acceptance if set to Yes If set Yes The SNMP function will be work Set the community of read operation Set the community of write operation Set the ip address of snmp trap Set another ip address of snmp trap Set another ip address of snmp trap Set another ip address of snmp trap This parameter defines the URI or IP address of the NTP server which is used by the Unicorn 2101 to set the current date time If set Yes device can get NTP server from DHCP option 42
41. net or just 20 seconds if it is performed on a LAN Users are recommended to conduct TF IP upgrade in a controlled LAN environment if possible For those who do not have a local TF TP server Hanlong technology provides a NAT friendly TFTP server on the public Internet for firmware upgrade Please check the Service section of Hanlong s Web site to obtain this TFTP server s IP address NOTES When Hanlong ATA boot up it will send TFTP or HTTP request to download configuration files there are two configuration files one is cfg txt and the other is cfg001fc1xxxxxx where 001fc1xxxxxx is the MAC address of the Unicorn 3112 These two files are for initial automatically provisioning purpose only for normal TFTP or HTTP firmware upgrade the following error messages in a TFTP or HTTP server log can be ignored 8 RESTORE FACTORY DEFAULT SETTINGS Warning Restoring to the factory default settings will delete all configuration information of the device Steps to follow in restoring to factory default settings kkk a Press or for voice prompt b Enter 99 and then you will hear the voice prompt Reset Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 38 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY c Enter the number 862584658050 A click sound will be heard d Wait for 15 seconds The device is now restored to the factory default setting 9 TECHNICAL SUPPORT CONT
42. not registered if allowed by ITSP but is unable to receive incoming calls This parameter defines the local SIP port the Unicorn 2101 will listen and transmit The default value for FXS port is 5060 The default value for FXO port is 5062 This parameter defines the local RTP RTCP port pair the Unicorn 2101 will listen and transmit It is the base RTP port for channel 0 When configured channel 0 will use this port value for RTP and the port value 1 for its RTCP channel 1 will use port value 2 for RTP and port value 3 for its RTCP The default value for FXS port is 5004 The default value for FXO port is 5008 This parameter when set to YES will force random generation of both the local SIP and RTP ports This is usually necessary when multiple Unicorn 2101 are behind the same NAT Default is NO If set to YES then for Attended Transfer the Refer To header uses the transferred target s Contact header information Sets the payload type for DIMF using RFC2833 This parameter specifies the mechanism to transmit DTMF digit in audio which means DTMF is combined in audio signal not very reliable with low bit rate codec Default is YES This parameter specifies the mechanism to transmit Unicorn 3112 User Manual Firmware 1 0 0 46 Page 23 of 39 Last Updated DTMF via SIP INFO Send Flash Event Enable Call Features Offhook Auto Dial Proxy Require Use NAT IP Preferred Vocoder Voice Frames per TX Hanlong Technolo
43. nt user ID Voice path volume adjustment Rx is a gain level for signals transmitted by FXS Tx is a gain level for signals received by FXS Default OdB for both parameters Loudest volume 6dB Lowest volume 6dB User can adjust volume of call on either end using the Rx Gain Level parameter and the Tx Gain Level parameter located on the FXS Port Configuration page lf call volume is too low when using the FXS port ie the ATA is at user site adjust volume using the Rx Gain Unicorn 3112 User Manual Page 34 of 39 Firmware 1 0 0 46 Last Updated PSTN AC Termination Enable PSTN Disconnect Tone Detection PSTN Disconnect Tone Enable Polarity Reversal Disconnect Enable Terminate Call After PSTN Silence Timeout PSTN Silence Timeout Life Line Mode Min Delay Before Dial PSTN ms DTMF Digit Volume dB DTMF Digit Length x10ms DTMF Dial Pause x10ms Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY Level parameter under the FXS Port Configuration page If voice volume is too low at the other end user may increase the far end volume using the Tx Gain Level parameter under the FXS Port Configuration page You can select the AC termination by Country or by Impedance If set to Yes arrived Busy Tone is used as the disconnect signal This configuration should be configured by the VoIP service provider Some country use single frequency tone to signal PSTN disconnection some country use double frequency
44. nter 9 to rotate among the following three options 17 Firmware Upgrade pale always check 12 check when pre suffix changes e never upgrade Se 5 Enter the target IP address to make a direct 47 Direct IP Calling IP call after dial tone See Make a Direct IP Call Enter 9 to reboot the device or Enter MAC address to restore factory default 99 RESET setting See Restore Factory Default Setting ae rere P E oer Section Invalid Entry Automatically returns to Main Menu Other Menu Prompt Features gt shifts down to the next menu option returns to the main menu 9 functions as the ENTER key in many cases to confirm an option e All entered digit sequences have known lengths 2 digits for menu option and 12 digits for IP address Once all of the digits are collected the input will be processed e Incorrect keyed entry cannot be deleted or undone The Unicorn 3112 will prompt you to start over by telling you that you made an error Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 8 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY 5 2 Make Phone call 5 2 1 Calling Phone or Extension Numbers Dial the number directly and wait for 4 seconds Default is 4 seconds To change the default change the settings via the web configuration page under No Key Entry Timeout Or Dial the number directly and press
45. nterprise class security Support snmp v2 e Support for Layer 2 802 1Q VLAN 802 1p and Layer 3 QoS ToS DiffServ MPLS Support automated NAT traversal without manual manipulation of firewall NAT Support device configuration via built in IVR Web browser or central configuration file through TFTP or HTTP Support firmware upgrade via TFTP or HTTP with encrypted configuration files Ultra compact wallet size and lightweight design great companion for travelers Compact lightweight Universal Power adapter 3 2 Hardware specification Unicorn 3112 LAN interface mn 1x RJ45 100MBase T 0000 Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 4 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY WAN interface et 1 x RJ45 100MBase T o FXS telephone port 1XFXS i FXO port PIESTA ee E E ee l LED light reen coke O ae _ Input 100 240VAC 50 60 Hz Universal switching power supply Output 5VDC 1200mA ee ULcertified Dimension 70mm W _X 130mm D x27mm H Weight 0 30kg i Ser 40 130F 4 INSTALLATIONS The Unicorn 3112 is an all in one VolP integrated device designed to be a total solution for networks providing VolP services The Unicorn 3112 VolP features are available when you connect any regular analog telephone to it Unicorn 3112 has one FXS port labeled Phone and one PSTN pass through port labeled Line After setting up the Unicorn 3112 you can make PSTN
46. o PSTN calls Stage Method 1 2 and indicates one or two stage dialing methods 6 1 7 Saving the Configuration Changes Once a change is made users should click on the SaveSet button in the Configuration page as follow End User Password O No Yes Unit will not respond to PING from WAN side if set to No O No Yes WAN side access to http server will be rejected if set to No Number of Rings PSTN Ring Thru FXS SDR eM ll0 MT a sSO B Reply to ICMP on WAN port f VAN side http access O No Yes Default Yes ilf set to yes all incoming PSTN calls will ring the FXS port after the Ring Thru Delay Sip Destination Port Al Rig shts Re d Hamong Eng Techaslogy CO LTD 2005 2008 The Unicorn 3112 will then display the following screen to confirm that the changes have been saved Please allow 5 to 10 seconds before rebooting the device SAVING Your changes have been saved Hanlong sboot the device VOIP Device TEE All Rights Reserved Handlong Technology CO LTD 2005 2008 Configuration sii pass Akasa DEVICE STATUS BASIC OPTIONS SUPER OPTIONS FXS PORT FXO PORT Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 36 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY 6 1 8 Rebooting the Unicorn 3112 You can reboot the Unicorn 3112 by clicking on the Reboot button after each update to the configuration pag
47. oIP number Calls are unconditionally forwarded to the specified VoIP phone number once users dial the FXO port PSTN number 6 1 6 3 Super Option Setting options Admin Password Layer 3 QoS Layer 2 QoS Data VLAN Tag STUN server keep alive interval Firmware Upgrade and Provisioning Hanlong Technology Co Ltd 1 19 2012 SUPER OPTIONS Definitions This contains the password to access the Advanced Web Configuration page This field is case sensitive Only the administrator can configure the Advanced Settings page Password field is purposely left blank for security reasons after clicking update and saved The maximum password length is 26 characters only digit or letter This field defines the layer 3 QoS parameter which can be the value used for IP Precedence or Diff Serv or MPLS Default value is 48 This contains the value used for layer 2 VLAN tag Default setting is 0 When using Bridge Mode Data VLAN Tag is supported when your PC connect to LAN Port data from your PC to switch will be tagged with Data VLAN Tag IP address or domain name of stun server This parameter specifies how often the Unicorn 2101 sends a blank UDP packet to the SIP server in order to keep the hole on the NAT open Upgrade or provisioning through TFTP or TFTP server Upgrade Via select HTTP or TFTP mode Allow DHCP Option support 66 128 150 If select yes device will get server information from DHCP option a
48. ocking the Caller ID from displaying Default is NO if set to YES the anonymous call will be rejected with busy message Check the SIP User ID in Request URI If they don t match the call will be rejected The session timer extension enables SIP sessions to be periodically refreshed via a re INVITE request Once the session interval expires if there is no refresh via a re INVITE message the session will be terminated Session Expiration is the time in seconds at which the session is considered timed out if no successful session refresh transaction occurs beforehand The default value is 180 seconds Default is 180 seconds The minimum session expiration in seconds Default is 90 seconds lf selecting Yes the device will use session timer when it makes outbound calls if remote party supports session timer Default is NO If selecting Yes the phone will use session timer when it receives inbound calls with session timer request Default is NO If selecting Yes the device will use session timer even if the remote party does not support this feature Selecting No will allow the device to enable session timer only when the remote party support this feature To turn off Session Timer select No for Caller Request Timer Callee Request Timer and Force Timer Default is NO As a Caller select UAC to use the device as the refresher or UAS to use the Callee or proxy server as the refresher De
49. port which also serves as a pass through connection for internet network access for your PC of the Unicorn 3112 Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 16 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 HAN LON G TECHNOLOGY 6 1 4 User Programming and Configuration From your web browser the Unicorn 3112 will show the following login screen Hanlong VOIP Device Configuration gin All Rights Reserved Hanlong Technology CO LTD 2005 2008 Enter the password and click on the Login button 6 1 5 Passwords Passwords are case sensitive and all Unicorn devices come with factory default passwords as indicated below Advanced User Password for access to Super User Options admin End User Password for access to Basic User Options 1234 Pages available for the end user are e Device Status e Basic Options Additional pagess available to super user are e Super Options e FXS port e FXO port 6 1 6 End User Settings After a correct password is entered in the login screen the embedded web server inside the Unicorn 3112 will show the configuration page which is explained in details below 6 1 6 1 Device Status DEVICE STATUS Hanlong Technology Co Ltd Unicorn 3112 User Manual Page 17 of 39 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY Setting Options Definitions MAC Address The device ID f HEX format This is a very important ID for ISP troubleshooting WAN IP Addr
50. s the Web Configuration Menu This field is case sensitive If set to Yes the Unicorn2101 will respond to the PING command from other computers but it also is vulnerable to the DOS attack Default is No lf this parameter is set to No the Http access via WAN port is disabled Default is 4 This setting specifies number of phone rings on the phone connected to the FXS port before a PSTN incoming call is bridged to VoIP Note The number of rings feature serves as a PSTN answer delay and should be set to a larger value to allow enough time for the Unicorn3112 to decode the Caller ID signal set by the central office lf Yes the phone connected to the FXS port will ring a configured amount of times See above If not the phone connected to the FXS port will not ring lf the PSTN Ring Thru Delay is set to Yes all incoming PSTN calls through FXO will ring the phone connected to the FXS port after this delay or after caller id is detected whichever comes first This field allows users to customize their own code to access PSTN Default is 00 Enter digits to authorize calling PSTN numbers from VOIP default is no Enter digits to authorize calling VOIP terminals from PSTN default is no Calls are unconditionally forwarded to the specified PSTN Unicorn 3112 User Manual Page 19 of 39 Firmware 1 0 0 46 Last Updated Forward to PSTN Unconditional Call Forward to VOIP TECHNOLOGY phone number once users dial the FXO port V
51. seconds Party A can hangs up the phone e Note Call features have to be activated during web configuration by selecting YES to Enable Call Features These features need to be supported by your SIP gatekeeper proxy server in order to work Party A can hold on to the phone and wait for one of the three following events 1 Aquick confirmation tone temporarily using the call waiting indication tone followed by a dial tone This indicates the transfer is successful transferee has received a 200 OK signal from transfer target At this point party A can either hang up or make another call 2 Aquick busy tone followed by a restored call on supported SIP gatekeeper platforms only This means the transferee has received a 4xx response signal for the INVITE and will try to recover the call The busy tone is just to indicate to the transferor that the transfer has failed 3 Busy tone keeps playing This means the Unicorn 3112 has failed to receive the second NOTIFY signal from the transferee and decided to time out Note this does not indicate the transfer has been successful nor does it indicate the transfer has failed When transferee uses a device that does not support the second NOTIFY signal this will be the case In poor or unstable network scenarios this could also happen although the transfer may have been completed successfully 5 2 9 Attended Transfer Assuming that call party A and party B are in conversation Party
52. thenticate Password Name Hanlong Technology Co Ltd 1 19 2012 FXS PORT Definitions Set to the YES the account can be available SIP Server s URI or IP address SIP Outbound Proxy Server s URI or IP address Select transport between UDP and TLS default is UDP This parameter defines whether the Unicorn 2101 NAT traversal mechanism will be activated or not lf Choosing No nothing to do lf Choosing No but send keep alive the Unicorn 2101 will periodically every 20 seconds or so send a blank UDP packet with no payload data to the SIP server to keep the hole on the NAT open lf choosing STUN and a STUN server is also specified then the Unicorn 2101 will behave according to the STUN client specification Under this mode the embedded STUN client inside the Unicorn 2101 will attempt to detect if and what type of firewall NAT it is sitting behind through communication with the specified STUN server If the detected NAT is a Full Cone Restricted Cone or a Port Restricted Cone the Unicorn 2101 will attempt to use its mapped public IP address and port in all its SIP and SDP messages If choosing STUN with no specified STUN server the Unicorn 2101 will periodically every 20 seconds or so send a blank UDP packet with no payload data to the SIP server to keep the hole on the NAT open lf choosing UPNP the embedded UPNP client inside the Unicorn 2101 will attempt to mapping ports with the router by upnp protocol SIP ser
53. vice subscriber s User ID SIP service subscriber s Authenticate ID Can be identical to or different from SIP User ID SIP service subscriber s account password SIP service subscriber s name which will be used for Caller ID display Unicorn 3112 User Manual Page 22 of 39 Firmware 1 0 0 46 Last Updated Use DNS SRV User ID is phone number SIP Registration Unregister On Reboot Register Expiration Outgoing Call without Registration Local SIP port Local RTP port Use random port Refer To Use Target Contact DTMF Payload Type DTMF in Audio DTMF via RFC2833 Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY Default is No If set to Yes the client will use DNS SRV for server lookup lf the Unicorn 2101 has an assigned PSTN telephone number this field should be set to Yes Otherwise set it to No If Yes is set a user phone parameter will be attached to the From header in SIP request This parameter controls whether the Unicorn 2101 needs to send REGISTER messages to the proxy server The default setting is Yes Default is No If set to Yes the SIP user will be unregistered on reboot This parameter allows the user to specify the time frequency in minutes the Unicorn 2101refreshes its registration with the specified registrar The default interval is 6 minutes The maximum interval is 65535 minutes about 45 days Default is No If set to Yes user can place outgoing calls even when

Download Pdf Manuals

image

Related Search

Related Contents

TGR-T2 series MANUALE UTENTE  KOHLER K-7273-BN Installation Guide  user manual  Philips myGarden Pedestal/post 16941/87/16  MANUEL D`UTILISATION - Aéroclub ASPTT Poitiers  Samsung Galaxy S4 User Manual(LL)    

Copyright © All rights reserved.
Failed to retrieve file