Quick Start Guide of DS-7200HVI-ST DVR
Contents
1. Next button to enter the Export menu 6 Select device to export to from drop down list USB Flash Drive USB HDD and DVD Writer If backup device is not recognized Click the Refresh button Reconnect device Check for compatibility from vendor 7 Click Start to begin backup process 8 After the backup process has completed you may select the files from your device and click the Play button to verify that it has been exported successfully Note Video Player software will automatically be copied on to the device that the recorded files were exported on Quick Start Guide DS 7200HVI ST Series DVR Quick Start Guide IS OE a R HIK VISION Using the Front Panel Controls DS 7204HVI ST Front Panel 1 Status Indicators POWER the POWER indicator turns green when DVR is powered up STATUS the indicator lights when compound key switches to numeric letter input mode Tx Rx TX RX indictor flickers green when network connection is functioning normally IR Receiver operation by IR remote control 3 Compound Buttons 1 MENU 1 Enter numeral 1 2 Access the main menu interface 2ABC F1 1 Enter numeral 2 2 Enter letters ABC 3 The F1 button when used in a list field will select all items on the list In PTZ Control mode it will turn on off PTZ light 3DEF F2 1 Enter numeral 3 2 Enter letters DEF 3 The F2 button is used to cycle through tab pages It wi2. aii gdadid a af a enable the recording schedule and have it record continuously all day 15 Click the OK button This will take you ede pepe pete deb batetabe peped pe EE Beg ERR eee Peds pepe ad pete kh beaded ids peted pe ET NNE BERS EEPEEBEE ED ERE BERS EESBERER TD ERE EE ERE Eee DES RPE pe Eee Pees SRB SEU Aee a e a ease I Bw E back to the Schedule tab To copy the schedule to a different channel select the channel or all under Copy To and click the Copy button 16 Click the Next Enter Network Settings button This will i take you to the Network Settings window Previous Next Cancel 17 To configure network settings click the Enter button 18 Enter the IP Address Subnet Mask and Default Gateway 19 Click the OK button to return to the Setup Wizard 20 Click the Next button Neteok Settings sone Lananced Pinetvort Status This will take you to TANGO Ao E the Camera nisin anmenn Management msn window 21 Select Add to add IP camera and click OK to return to Setup Wizard 22 If all the settings are entered as desired click the Done button to finish and exit the Setup Wizard Congratulations You ve completed the Setup Wizard The next step in the initial setup process is to setup the system date and time Setting Date amp Time It is extremely important to setup the system date and time to accurately timestamp recordings
3. in the live preview window provides a series of PTZ control buttons as shown in the following figure 2 l Zoom Preset 3 i Focus Patrol z iris Patten Speed 3 DWP AQEs Exit 1 Directional Pad Auto scan Buttons Controls the movements and directions of the PTZ The center button is also used to start auto scan of PTZ Zoom Used to zoom in and out with the PTZ Focus Used to adjust the focus of the PTZ Iris Used to open up or close the iris of the PTZ Speed Adjusts the movement speed of the PTZ Light Turns PTZ light if applicable on and off Wiper Turns PTZ wiper if applicable on and off Zoom In Instantly zooms PTZ in gt P Fee eS MN Center Centers PTZ Camera Select a PTZ camera Preview Menu Call Preset Call a PTZ preset Camera Call Patrol Call a PTZ patrol Call Presel Call Pattern Call a PTZ Call Patrol pattern Call Pattem Presel Sellings Preset Settings Enter PTZ Patrol Settings preset configuration menu Pattern Settings PTZM Patrol Settings Enter PTZ zaila PTZ Settings patrol configuration menu sca FUIK VISION Pattern Settings Enter PTZ pattern configuration menu PTZ Menu Enter PTZ menu PTZ Settings Enter PTZ settings menu Playback Playback by Search To playback files from a general search 1 Enter into the Video Search menu by clicking Menu gt Video Search 2 Select General tab and Set the search param
4. 2 Enter letters DEF 3 The F2 button is used to cycle through tab pages It will also bring up the Channel amp OSD Position settings 4GHI ESC 1 Enter numeral 4 2 Enter letters GHP 3 Exit and back to the previous menu 5JKL EDIT 1 Enter numeral 5 2 Enter letters JKL 3 Delete characters before cursor 4 Select the checkbox and ON OFF switch 5 Start stop record clipping in playback 6MNO PLAY 1 Enter numeral 6 2 Enter letters MNO 3 Playback for direct access to playback interface TPQRS REC 1 Enter numeral 7 2 Enter letters PQRS 3 Manual record for direct access to manual record interface manually enable disable record STUV PTZ 1 Enter numeral 8 2 Enter letters TUV 3 Access PTZ control interface 9WXYZ PREV 1 Enter numeral 9 2 Enter letters WXYZ 3 Multi camera display in preview 0 A 1 Enter numeral 0 2 switch between input methods upper and lowercase alphabet symbols and numeric input SHIFT Switch of compound keys between the numeric letter input and functional control Control Buttons Directional buttons In menu mode the direction buttons are used to navigate between different fields and items and select setting parameters In playback mode the Up and Down buttons are used to speed up and slow down record play and the Left and Right buttons are used to select the recording 30s forwards or ba
5. Quick Start Guide DS 7200HVI ST Series DVR V1 0 2 Menu Structure The menu structure of the DS 7200HVI ST Series DVR is as followed VENU ee EE EE EE mna meo AR manua woo sermos wumac neir suur oom I CENERAL UPGRADE LOCK 1 i l CAMERA LOG SEARCH SHUT DOWN I I RECORD OEFAULT REBOOT I I NETWORK COW GURAT HON I i ALARM INFORMATION L PTZ I Rin 1 OGPLAY i EXCEPTION i USER Startup and Shutdown Proper startup and shutdown procedures are crucial to expanding the life of your DVR To start your DVR 1 Ensure the power supply is plugged into an electrical outlet It is HIGHLY recommended that an Uninterruptible Power Supply UPS is used in conjunction with the unit 2 Press the POWER switch on the rear panel After the power has been started up the POWER indicator will light green To shut down the DVR 1 Enter the Shutdown menu by clicking on Menu gt ShutDown Shut Down A ShutDown Reboot Cancel 2 Select the ShutDown button 3 Click the Yes button Using the Setup Wizard By default the Setup Wizard will start once the DVR has loaded The Setup Wizard will walk you through some of the MIK VISION more important settings of your DVR If you do not wish to use the Setup Wizard at this time click the Cancel button You may also choose to use the Setup Wizard at a later time by leaving the Start Wizard when DVR starts checkbox checked To
6. REC 1 Enter numeral 7 2 Enter letters PQRS 3 Manual record for direct access to manual record interface manually enable disable record STUV PTZ 1 Enter numeral 8 2 Enter letters TUV 3 Access PTZ control interface 9WXYZ PREV 1 Enter numeral 9 2 Enter letters WXYZ 3 Multi camera Quick Start Guide DS 7200HVI ST Series DVR 7 FUK VISION display in preview e O A 1 Enter numeral 0 2 switch between input methods upper and lowercase alphabet symbols and numeric input 8 JOGSHUTTLE Control The JOG SHUTTLE control can be used to move the active selection in a menu The inner ring will move the selection up and down the outer ring will move it left and right In the Playback mode the inner ring is used to jump 30 seconds forward backward in a video The outer ring can be used to speed up slow down the video In Preview mode it can be used to cycle through different channels 8 Quick Start Guide DS 7200HVI ST Series DVR
7. and events To set date and time Generel Settings enetal FROST Settings Mion Settings 1 Enter General Settings z pl rc ike Une menu by clicking m z Cv ai Standard PAL ot TENSHI GMT O 00 Bajing Une WO ye TAA E General War Teen Menu gt Settings gt 2 Enter the correct date and time under System Time 3 Click the Apply button to save the setting Live View Some icons are provided on screen in Live Preview mode to indicate different camera status These icons include M Main Output Lay Aux Output Event Alarm Indicates video loss video tampering motion detection or relay alarm ete Record Indicates the current channel is recording The recording may have been started manually from a schedule and or triggered from motion or alarm Event Alarm amp Record PTZ Control Settings for a PTZ camera must be configured before it is used Before proceeding verify that the PTZ and RS 485 of 2 Quick Start Guide DS 7200HVI ST Series DVR the DVR are connected properly PTZ Settings To configure PTZ settings 1 Click Menu gt Settings gt PTZ to enter the PTZ Settings menu 2 Select channel where PTZ camera is installed next to Camera label 3 Configure the settings of baud rate date bit stop bit parity flow control PTZ protocol and address 4 Click OK to save settings and exit the PTZ Settings menu PTZ Control The PTZ control panel
8. annels Enter The Enter button is used to confirm selection in menu mode or used to select checkbox fields and ON OFF switch In playback mode it can be used to play or pause the video In single frame play mode pressing the Enter button will advance the video by a single frame And in auto sequence preview mode the buttons can be used to pause resume auto sequence 6 USB Interface Connects USB mouse or USB flash memory devices Quick Start Guide DS 7200HVI ST Series DVR 5 6 FUK VISION DS 7208HVI ST Front Panel 2 3 4 5 6 1 USB Interface Connects USB mouse or USB flash memory devices 2 Status Indicators POWER the indicator lights in green when DVR is powered up READY the indicator lights in green when the device is running normally STATUS the indicator lights when compound key switches to numeric letter input mode ALARM the indicator lights in red when there is sensor alarm occurring HDD the indicator flickers in red when HDD is reading writing Tx Rx TX RX indictor flickers green when network connection is functioning normally 3 IR Receiver operation by IR remote control 4 Compound Buttons 1 MENU 1 Enter numeral 1 2 Access the main menu interface 2ABC F1 1 Enter numeral 2 2 Enter letters ABC 3 The F1 button when used in a list field will select all items on the list In PTZ Control mode it will turn on off PTZ light 3DEF F2 1 Enter numeral 3
9. ckwards In preview mode these buttons can be used to cycle through channels Enter The Enter button is used to confirm selection in menu mode or used to select checkbox fields and ON OFF switch In playback mode it can be used to play or pause the video In single frame play mode pressing the Enter button will advance the video by a single frame And in auto sequence preview mode the buttons can be used to pause resume auto sequence Quick Start Guide DS 7200HVI ST Series DVR FIIK VISION DS 7216HVI ST Front Panel 3 6 4 5 7 8 1 IR Receiver operation by IR remote control USB Interface Connects USB mouse or USB flash memory devices 3 Status Indicators POWER the indicator lights in green when DVR is powered up READY the indicator lights in green when the device is running normally STATUS the indicator lights when the compound key switches to numeric letter input mode ALARM the indicator lights in red when there is sensor alarm occurring HDD the indicator flickers in red when HDD is reading writing Tx Rx TX RX indictor flickers green when network connection is functioning normally 4 DVD ROM Space for DVD ROM 5 Control Buttons Directional buttons In menu mode the direction buttons are used to navigate between different fields and items and select setting parameters In playback mode the Up and Down buttons are used to speed up and slow down record play and the Left and Right buttons are use
10. d to select the recording 30s forwards or backwards In preview mode these buttons can be used to cycle through channels Enter The Enter button is used to confirm selection in menu mode or used to select checkbox fields and ON OFF switch In playback mode it can be used to play or pause the video In single frame play mode pressing the Enter button will advance the video by a single frame And in auto sequence preview mode the buttons can be used to pause resume auto sequence 6 SHIFT Switch of compound keys between the numeric letter input and functional control 7 Compound Buttons 1 MENU 1 Enter numeral 1 2 Access the main menu interface 2ABC F1 1 Enter numeral 2 2 Enter letters ABC 3 The F1 button when used in a list field will select all items on the list In PTZ Control mode it will turn on off PTZ light 3DEF F2 1 Enter numeral 3 2 Enter letters DEF 3 The F2 button is used to cycle through tab pages It will also bring up the Channel amp OSD Position settings 4GHI ESC 1 Enter numeral 4 2 Enter letters GHP 3 Exit and back to the previous menu 5JKL EDIT 1 Enter numeral 5 2 Enter letters JKL 3 Delete characters before cursor 4 Select the checkbox and ON OFF switch 5 Start stop record clipping in playback 6MNO PLAY 1 Enter numeral 6 2 Enter letters MNO 3 Playback for direct access to playback interface TPQRS
11. eters by selecting cameras to search video file type and the start end time 3 Click the Play button 16 11 20 Mow 11 3 1 to start playback of all the files found with the specified search criteria or click the Search button to bring up the list of search results After search results are presented select the file you would like to playback and press Play to enter synchronous playback cameras selection 4 Recordings will automatically be played back in the Playback interface Playback from Live Preview You may also instantly playback from a channel while watching a Live Preview The playback will be of recordings from the past 5 minutes To playback from a channel instantly in Live Preview e Using a Mouse 1 Right click the mouse on desired channel and select the Playback button 2 Recordings from 29 12 2009 Tue 12 52 19 the selected channel will start playing back in the Playback interface An Attention Quick Start Guide DS 7200HVI ST Series DVR 3 FUIK VISION message will appear if there are no recordings found from the previous 5 minutes You may also press the Play button to view the day s recording for the selected channel You may also select additional channels for playback from the channel list on the right hand side of the Playback interface e Using the Front Panel Remote 1 Press the PLAY button This will take you into the Playback interface Enter the cha
12. ll also bring up the Channel amp OSD Position settings 4GHI ESC 1 Enter numeral 4 2 Enter letters GHP 3 Exit and back to the previous menu 5JKL EDIT 1 Enter numeral 5 2 Enter letters JKL 3 Delete characters before cursor 4 Select the checkbox and ON OFF switch 5 Start stop record clipping in playback 6MNO PLAY 1 Enter numeral 6 2 Enter letters MNO 3 Playback for direct access to playback interface TPQRS REC 1 Enter numeral 7 2 Enter letters PQRS 3 Manual record for direct access to manual record interface manually enable disable record STUV PTZ 1 Enter numeral 8 2 Enter letters TUV 3 Access PTZ control interface SWXYZ PREV 1 Enter numeral 9 2 Enter letters WXYZ 3 Multi camera display in preview 0 A 1 Enter numeral 0 2 switch between input methods upper and lowercase alphabet symbols and numeric input 4 SHIFT Switch of compound keys between the numeric letter input and functional control 5 Control Buttons Directional buttons In menu mode the direction buttons are used to navigate between different fields and items and select setting parameters In playback mode the Up and Down buttons are used to speed up and slow down record play and the Left and Right buttons are used to select the recording 30s forwards or backwards In preview mode these buttons can be used to cycle through ch
13. nnel you would like to view recordings for on the front panel or remote i e press SHIFT the STATUS light will turn green then press 1 for channel 1 press 2 for channel 2 Recordings will begin for the selected channel Playback from System Log You may also playback recordings from the System Log To playback video from the System Log 1 aw gt SY Enter the Log Search menu by clicking Menu gt Maintenance gt Log Search Set Major Type setting to Information Set Minor Type setting to Start Record or End Record Set Start Time and End Time Click the Search button A list of results with your search criteria will be displayed Select the video log to playback and click Play The recording will begin to play in the Playback interface Backup Recorded files can be backed up to various devices such as USB flash drives USB HDDs or a DVD writer To export recorded files 1 4 Enter the Export Video menu by clicking Menu gt Video Export 2 Select desired parameters to search for files to export 3 Press the Export button This will take you to the Video Search menu 4 Select the files to export You may also click the Play button to verify that these files are indeed the ones you would like to export 5 The size of the currently selected files is displayed in the lower left corner of the window Select the fer rou teen Pay roms San cance
14. start using the Setup vara amp Start wizard when DYR starts Wizard 1 Click the Next button on the Wizard window 2 This will take you to the User Permission window 3 Navigate to the Admin Password input field 4 Enter the admin password into the Admin Password input field By default Wizard the password is Enter HDO Management 12345 5 To change the admin password check the New Admin Password checkbox Enter the new password and confirm the password in the given fields 6 Click the Next button This will take you to the HDD Management window 7 To start HDD management click the Enter button 8 Ifa new HDD was recently installed select the HDD from the list to initialize it Initializing the HDD will format and remove all data from it 9 After the HDD has been initialized click the OK button which will take you back to the Setup Wizard window 10 Click the Next button This will take you to the Record Quick Start Guide DS 7200HVI ST Series DVR 1 FAK VISION Settings Window 11 To enter the Record Wizard Settings window Enter Record Settings click the Enter mer button 12 Select the Schedule tab Previous EXT Cancer 13 Click the Edit button This will open up a new recording schedule 14 Check both the Enable Schedule and All Day ib ai T O T E J checkbox This will ii h i b Bi oopan oo N F ooo 2 E E E E E E E
Download Pdf Manuals
Related Search