FS-Y1901D User Guide-EN
Contents
1. XX 11966 2 2015 GPIO There are four pins on the RJ9 GPIO connector Each pin has a pre programmed function assigned to it The function is initiated when the pin is grounded Pin 1 Pin 3 Primary and Secondary Swap Grounding Record Indicator The record indicator is this pin will swap the primary and second displayed in the top left corner when the ary image pin is ground to pin 4 The indicator will vanish when the contact is opened S Pin 4 Pin 2 Connector Ground This is the common PIP PBP1 PBP2 Single Continuously ground location grounding this pin causes the position and size choices to cycle Monitor RJ9 PIP PBP1 SINGLE Power Management This monitor does not adhere to the VESA DPMS standard when no signal is present on the video input Status LED sign Power Consumption FS Y1901D Normal mode Off 60W Standby mode Blinking 13W OSD power off Constant 13W DC power off Off 13W FSN1966 2 2015 JJ O TQ MA English 17 On Screen Display OSD Menus FSN display monitors come equipped with a rich set of features for system set up image adjustments and screen layout control These features are managed through the On Screen Display or OSD Some options presented in the OSD are contextual and vary dep2. X X X 11966 2 2015 Indicates proof of conformity to applicable European Economic Community Council directives and to harmonized standards published in the official journal of the European Communities Medical Equipment is in accordance with UL 60601 1 and CAN CSA C22 2 No 601 1 in regards to electric shock fire hazards and mechanical hazard Tested to comply with FCC Class B standard Indicates the display is approved according to the CCC regulations KM china RoHS labens This symbol indicates that the waste of electronic equipment must not be disposed as unsorted municipal waste and must be collected separately Please contact the manufacturer or other authorized disposal company to decommission your equipment Language English Note A printed copy of the manual in English is provided with the product Users within EU member states please contact local distributor for other languages or refer to the CD manual enclosed with the product This applies to EU member states where the product has been pur chased through authorized channels 1966 2 2015 D M English 5 Safety Instructions On Safety 1 Before connecting the AC power cord to the DC adapter outlet make sure the voltage desig nation of the DC adapter corresponds to the local electrical supply 2 Neverinsert anything metallic into the cabinet openings of the medical LCD moni
3. O jaanananama c c c cec uuu ac ac ac ac ac ac ac ac ar ac ac OOOOOOOOOOO aaaaaaaaaaa 00000000000 22222222222 zzzzzz2222zz 22222222222 MY NY NN IIIIIIIIIII 00000000000 aoaaaaoan M OVER SCAN 333333333 vM FSN1966 2 2015 On Screen Display OSD System Overview continued Submenu Descriptions Function Description IMAGE SETTING Save the 5 user s setting for BRIGHTNESS CONTRAST BACKLIGHT COLOR TEMP FILTER value separately PRESET1 PRESET2 USER1 USER2 USER3 ZOOM PAN Controls image ZOOM in out gt gt gt gt gt gt gt ko mo loO000000000 DOOOOOOOOU Immmmmmmmmm D mnnnnnnnnn O lnooo0000000l LILDIICIITIIXIIT Ecccececccecc IAAAAAAAAARARA ff lt lt lt lt lt lt lt lt lt lt lt lt 2222222222222 900 UU UU UV V 20 2020 2020 20 2020 2020 2020 20 lnnnnnnnnnnnnn 444444444 leeececcececcc ct D E 9 A mmmmmmm mnnnnnn 0000000 becom RKRRRRRRRRR fe ie es a EED 000000000 VVUVUVVUVUUUU OOOOOOO0O00 D20 202020 2020 2020 20 wn oO k C C
4. 4 Place your medical LCD monitor near an easily accessible AC outlet 5 High temperature can cause problems Don t use your medical LCD monitor in direct sunlight and keep it away from heaters stoves fireplaces and sources of heat 6 Don place your medical LCD Monitor on an unstable stand Medical LCD monitor may mal function or fall 7 This medical LCD monitor should not topple over when tilted at a 5 angle in any position during NORMAL USE excluding transport 8 Inthe position specified for transport medical LCD monitor shall not overbalance when tilted ata 10 degree angle 9 When carrying this product please use both handles if included on the left and right side of the product and carry using two people If you want the product to be installed in another place please call your service center 10 Do not use other cables or accessories that are not provided 11 Do not lay this monitor on the other equipment Environmental Conditions for Operation and Storage Temperature range within 0 to 40 operation 20 to 60 storage Relative humidity range 1096 to 8596 Atmospheric pressure range within 500 to 1060hPa Intended Use This Medical LCD Monitor is an accessory intended for use with Medical Equipment to display alphabetical numerical and graphical data FSN1966 2 2015 QM M MU M P English 7 Cautions Caution CAUTION RISK OF ELECTRICAL SHOCK DO NOT OPEN This
5. Power Supply AC DC Adaptor AC 100 240V DC 12V 7A Mounting Hole VESA standard 100mm X 100 mm 423 W x 351 5 H x 76 5 D mm 5 8 Kg 16 653 W x 13 838 H x 3 011 D inch 12 79 165 Dimensions Size and Weight 32 English X X 111966 2 2015 Cleaning Instructions Precautions Before cleaning switch the display in stand by position to prevent the control touch panel from being activated inadvertently by sweeping over the front filter In stand by position the touch panel cannot be activated by just sweeping over them To switch the display on again you must press the stand by key again Take care not to damage or scratch the front filter or LCD panel careful with rings or other jewelry that can touch the front filter not apply pressure on the front filter or LCD panel Do not apply or spray liquid directly to the front filter panel or cabinet as excess liquid may cause damage to internal electronics Instead apply the liquid to the cleaning cloth Follow your hospital protocol for the handling of blood and body fluids The display is not disinfected or packed in sterile environment Follow your hospital protocol in case the display needs to be disinfected prior to installation Front Filter Proceed as follows 1 Remove dust with a dry lint free non abrasive soft cotton cloth
6. 19 FS Y1901D Monitor Connector GROUND ON OFF VGA IN RS 232C SVC S VIDEO C VIDEO IN IN S VIDEO IN C OOO O DCIN DVI 1 IN DVI 1 OUT Mechanical Product Drawing 19 FS Y1901D Dimension 395 mm 15 55 in R Pr IN B Pb IN VS IN GIY IN HS CS IN t gt i lt Ar e i lt b pe 2 lt 2 Er lt A m 2 76 5 3 0 423 16 65 31 122 o gt 2 2 o 351 5 100 1304 VESA MOUNT dod o z HOLES Poo HU So 000000000 o 050 membrane switch 949 woe FSN1966 2 2015 c J co 00000 Controls On Screen Display OSD Buttons An 8 button keypad located in bottom right corner on the front of the display allows the user to make adjustments to various display parameters using the On Screen Dis play OSD system QUICK ADJUST Press QUICK ADJUST Press to enable PIP No Light Normal display has to decrease the display Press to decrease Picture in Picture power and an active signal contrast No need to the display bright function enter the OSD main ness No need to Blinking Light Standby Mode no menu enter the OSD main Select from active
7. 2 Remove fingerprints or grease using a lint free non abrasive soft cotton cloth that is lightly moistened with plain water or a mild commercial glass cleaning product suited for coated glass surfaces 3 Gently wipe dry with a dry cloth The following products are tested and approved Misty Clear Lemon 10 Disinfectant e Bohle glass cleaner Zep Heavy duty glass amp all surface cleaner Klear Screen Screen TFT Kontakt Chemie Incidin Foam Ecolab Microzid Mild detergent Isopropyl alcohol with concentration lt 5 Household bleach generic sodium hypochlorite solutions of 5 2596 sodium hypochlorite diluted with water between 1 10 and 1 100 FSN1966 2 2015 O A m English 33 Cleaning Instructions continued Precautions Do NOT use on front filter Alcohol solvents at higher concentration gt 5 Strong alkalis strong solvents Acid Detergents with fluoride Detergents with ammonia Detergents with abrasives Steel wool Sponge with abrasives Steel blades Cloth with steel thread Cabinet Proceed as follows Clean the cabinet using a soft cotton cloth lightly moistened with a recognized cleaning prod uct for medical equipment Repeat with water only Wipe dry with a dry cloth The cabinet has been tested for resistance to the following products Virex Ready to use Disinfectant Cleaner Misty Clear Lemon 10 Disinfectant
8. FSN Medical Technologies Medical Display FS Y1901D User s Guide Before connecting operating or adjusting this product please read this instruction booklet carefully and completely Table of Contents RO pa rn LE 3 Symbol Definitions llle 4 Safety Instructions ee eee 6 CAULIONS 8 Information eig Y RR REA 10 a quate S dieat E i Sate ah dc ack 14 Connectors Mechanical 15 CONOIS jects tat tase yo Boa otra ey a E 16 On Screen Display OSD llle 18 Standard Signal Tables 28 Signal Connector Pin Assignments 29 GeneralSpecification 2l 32 Cleaning Instt ctlons sss son x Rr A eons 33 Fiber 1 5 35 Contacts r va RA RR VUE NOE 36 The specifications and information in this document are subject to change without notice 2 English FSN1966 2 2015 Overview FS Y1901D This product from FSN Medical Technologies is a high end surgical display monitor designed for advanced digital OR applications This medical display is uniquely equipped to handle tasks in the demanding operating room environment This unit features LED backlight technology We have implemented methods to
9. Range 0 100 3 GREEN Green balance Only works with USER mode Range 0 100 4 BLUE Blue balance Only works with USER mode Range 0 100 Submenus under the IMAGE menu 1 IMAGE SIZE Changes the image size FULL FILL ASPECT 1 1 NORMAL 2 H POSITION Adjusts the horizontal position of the displayed source image Range 0 100 3 V POSITION Adjusts the vertical position of the displayed source image Range 0 100 4 GAMMA Adjusts GAMMA value VIDEO BYPASS 1 8 2 0 2 2 2 4 2 6 PACS 5 FILTER Sets the sharpness of image Softest Soft Normal Sharp Sharpest 6 OVER SCAN Adjusts the displayed size 0 8 7 IMAGE SETTING Changes the image setting Preset 1 2 User 1 2 3 8 ZOOM PAN Enlarges the image moves images left and right 9 FREEZE Keeps the image still Submenus under the SETUP menu 1 LANGUAGE Changes the OSD language 8 languages 2 OSD COLOR Adjusts the OSD background from white opaque to translucent 3 OSD POSITION Changes the OSD position 9 Positions 4 DURATION Adjusts the length of time the OSD Menu is present on the screen 5 10 20 30 60 90 120 180 240 seconds 5 RESET SETTINGS Changes all the OSD values to factory default 6 AUTO SOURCE SELECT Disables or enables auto source select ON Searches through all possible input sources until an active video source is found OFF Video input is manually selected 7 INACTIVE INPUT Change the input source between RGBs and YP
10. 100 4 BLUE Blue balance Only works with USER mode Range 0 100 Submenus under the IMAGE menu 1 IMAGE SIZE Changes the image size FULL FILL ASPECT 1 1 NORMAL 2 GAMMA Adjusts GAMMA value VIDEO BYPASS 1 8 2 0 2 2 2 4 2 6 PACS 3 FILTER Sets the sharpness of image Softest Soft Normal Sharp Sharpest 4 OVER SCAN Adjusts the displayed size 0 8 5 IMAGE SETTING Changes the image setting Preset 1 2 User 1 2 3 6 ZOOM PAN Enlarges the image moves images left and right 7 FREEZE Keeps the image still Submenus under the SETUP menu 1 LANGUAGE Changes the OSD language 8 languages 2 OSD COLOR Adjusts the OSD background from white opaque to translucent 3 OSD POSITION Changes the OSD position 9 Positions 4 DURATION Adjusts the length of time the OSD Menu is present on the screen 5 10 20 30 60 90 120 180 240 seconds 5 RESET SETTINGS Changes all the OSD values to factory default 6 AUTO SOURCE SELECT Disables or enables auto source select ON Searches through all possible input sources until an active video source is found OFF Video input is manually selected 7 INACTIVE INPUT Change the input source between RGBs and YPbPr 8 PICTURE DELAY Adjust the picture delay 0 Disable deinteracer engine 1 Enable deinteracer engine Submenus under the PIP menu 1 LAYOUT Changes the layout OFF PIP PBP1 PBP2 2 SOURCE Changes the secondary source 3 SIZE Changes the PIP size
11. Any such ground must be installed in accordance with applicable electrical codes The ground post is shown on the mechanical drawing found in this user s guide Recycling Follow local governing ordinances and recycling plans regarding the recycling or disposal of this equipment Cleaning Instructions Follow your hospital protocol for the handling of blood and body fluids Clean the display with a diluted mixture of mild detergent and water Use a soft towel or swab Use of certain detergents may cause degradation to the labels and plastic components of the product Consult cleanser manufacturer to see if agent is compatible Do not allow liquid to enter the display Servicing Do not attempt to service the medical LCD monitor yourself as opening or removing covers may expose you to dangerous voltages or other hazards and will void the warranty Refer all servicing to qualified service personnel Unplug the medical LCD monitor from its power source and refer servicing to qualified personnel under the following conditions If the power cord or plug is damaged or frayed If liquid has been spilled into the medical LCD monitor If objects have fallen into the medical LCD monitor If the medical LCD monitor has been exposed to rain or moisture If the medical LCD monitor has been subjected to excessive shock by being dropped If the cabinet has been damaged If the medical LCD monitor seems to be overheated If the medica
12. C C RAAAA rr T K lt lt lt S zzz DOO CII Controls the image PAN left right up down The maximum ZOOM size is ten times as large as the original FREEZE Freezes the main image Does not freeze secondary image in PIP mode LANGUAGE Changes the OSD to one of 9 languages ENGLISH GERMAN FRENCH SPANISH ITALIAN JAPANESE CHINESE KOREAN Adjusts the transparency of the OSD menu box OSD COLOR i OSD POSITION 26 English FSN1966 2 2015 On Screen Display OSD System Overview continued Submenu Descriptions Function Description OSD DURATION Adjusts the time until the OSD menu will disappear after making adjustments RESET SETTINGS Resets the unit to its original status when it left the factory When set to ON the monitor will automatically search for connected input sources AVTOINPUT SELECT Does not affect the sub window when in PIP mode INACTIVE INPUT Change the input source between RGBs and YPbPr Change sub window layout SINGLE PIPPBP1 PBP2 PIP Main Sub window doesn t change aspect ratio PBP1 Main Sub window doesn t change aspect ratio PBP2 Main Sub window H V display 1 1 size Selects the PIP source input Change other sub windows through OSD pip menu The following table shows PIP matching options with the main and sub window Sub window Input DVI DSUB source DIGITAL 1 ANALOG DVI DIGITAL 1 DSUB ANALOG SDI PIP SOURC
13. UT for 5 cycle 70 Ut 30 dip in Ur for 25 cycle lt 5 Ut lt 95 dip in Ur for 5 sec 3V m 80 0 MHz to 2 5 GHz Power frequency magnetic fields should be at levels characteristic of a typical location in atypical commercial or hospital environment Main power quality should be that of a typical commercial or hospital environment If the user of monitor requires continued operation during power mains interruptions itis recommended that monitor be powered from an uninterruptible power supply or a battery Note Ur is the A C mains voltage prior to application of the test level Recommended separation distance 80MHz to 800MHz le 80MHz to E 2 5GHz Where P is the maximum output power rat ing of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in meters m Field strengths from fixed RF transmit ters as determined by an electromagnetic site survey should be less than the compli ance level in each frequency range FSN1966 2 2015 4 Recommended separation distances between portable and mobile RF communications equipment and this medical LCD monitor The medical LCD monitor is intended for use in an electromagnetic environment in which radi ated RF disturbances are controlled The customer or the user of the monitor can help prevent electromagnetic interference by maintaining a minimum distance between portable and mo
14. d OOOOOOOOOC 0 0 0 0 0n 0 n a o OOOOOOOOO 222222222 zzzz2222zz 21212121 IIICIIIEI OO0000000 LL LLL LL n 2 OQOOOOOQO aaa a a o a 2222222 gt gt gt gt gt gt gt 5555555555555 ln uua nnn la a cc cc oc oc oc oc c ox acce looooooooooooo 2222222222222 2525555555555 5555555555555 v VV vv cC ac ac ec ac ac ac ec ac n 0 0 0 n n n n a d 2222222222 zzzzzzzzz3 pa a a OcOOOooooo oe a Ee E a zzzzzzzz EE M rum T Irrrrrrrrrrrr loco 00000009000 aaaaaaoaaaaaa iaoooo2aaa I c c c t lt lt IIIIIIIIIj LL LLL LL LL LL LLL 4r QOOOOOQU ITIIIIIII LL LL m paw 5555555555555 A IE nuno wu lec acc oc cc oc cc ac ac oc oc loococoocoooooo a na a a looooooooooooo 2222222222222 gt gt gt gt gt gt gt gt gt gt gt gt gt 2255555555555 zz V IIrrrrrrrrrrr loO00000000000 uc u u tcu Qaaaaaaaaa
15. fine tune the properties of FSN displays Distinct color space settings have been calibrated to well known surgical color preferences providing the user with the ideal surgical visualization system Features include Rapid signal detection robust mode tables Artifact free HD images Fanless sterile field compatible Calibrated to clinical color Image pan zoom freeze picture in picture FSN Medical Technologies has solutions for managing your operating room video signals Our products are engineered and built for compatibility with other highly specialized surgical and diagnostic equipment used in surgical suites operating rooms emergency rooms and proce dural facilities FSN1966 2 2015 D M English 3 Symbol Definitions The following symbols appear on the product its labeling or the product packing Each symbol carries a special definition as defined below Dangerous High Voltage Power adapter Indicates equipotential earth Direct Current ground Indicates protective earth Indicates top bottom ground direction Do not get wet B Maximum Stacking Consult the operating instruc Indicates the tions manufacturer Indicates the Authorized representative manufacturing date the European community E Serial Number Humidity limitation t Atmospheric pressure Temperature limitation P limitation 4 English
16. input source between RGBs and YPbPr 8 PICTURE DELAY Adjust the picture delay 0 Disable deinteracer engine 1 Enable deinteracer engine Submenus under the PIP menu 1 LAYOUT Changes the layout OFF PIP PBP1 PBP2 2 SOURCE Changes the secondary source 3 SIZE Changes the PIP size Small Large 4 POSITION Changes the PIP position 5 SWAP Swaps the position of the Primary and Secondary images 20 English X XX w 111966 2 2015 Submenus for the following signal types YPbPr After selecting a main menu category press the button to enter the associated submenus as shown below Next use the UP and Down V buttons to navigate to the desired submenu then adjust as needed with the and buttons Select the MENU button to exit from the submenu or main menu FSN1966 2 2015 Submenus under the ADJUST menu 1 BRIGHTNESS Increases or decreases the brightness Range 0 100 2 CONTRAST Increases or decreases the contrast Range 0 100 3 SHARPNESS Adjusts the sharpness of video image Range 0 100 4 SATURATION Changes the tone of color Range 0 100 5 COLOR Changes the richness of color Range green 0 50 red 0 50 6 BACKLIGHT Adjust backlight dimming level Range 0 100 7 CLOCK Increases or decreases the sampling frequency Range 0 100 8 PHASE Increases or decreases the Pha
17. signal is present menu PIP When the OSD menu PBP1 Constant Light Off Mode power is activated press to When the OSD PBP2 to the LCD screen has been turned decrease the adjust menu is activated off using the OSD power button ment of the selected press to move the however the display unit is still con function menu selection nected to a power source downward Note 1 Normal and Off Mode behavior of the Power Indicator Light can be changed according to the requirements of the customer Constant light can be changed to indicate Normal if desired Note 2 The main AC power switch on the dis play s back panel should be in the ON position The front OSD power button is used to turn on the LCD screen on and off INPUT MINUS PLUS Press to showthe QUICK ADJUST QUICK ADJUST Press to activate Press to turn input selection Press to increase Press to increase the OSD menu power on off to menu and to the display the display bright the display s front change the display contrast No need ness No need to When the OSD LCD screen signal source to enter the OSD enter the OSD menu is active main menu main menu press to exit from Input choices the main menu or DVI 1 SDI When the OSD When the OSD submenu VGA RGBS YPbPr menu is activated menu is activated S VIDEO C VIDEO press to increase press to move the the adjustment of menu selection the selected func upward tion 16 English
18. symbol alerts the user that important literature concerning the operation of this unit has been included Therefore it should be read carefully in order to avoid potential problems This symbol warns users that un insulated voltage within the unit may have sufficient magnitude to cause electrical shock Therefore it is dangerous to make contact with any part inside the unit To reduce the risk of electrical shock DO NOT remove cover or back There are no user serviceable parts inside Refer servicing to qualified service personnel To prevent fire or shock hazards do not expose this unit to rain or moisture Do not use this unit s polarized plug with an extension cord receptacle or other outlets unless the prongs can be fully inserted This display is designed to meet the medical safety requirements for a patient vicinity device This device may not be used in connection with life support equipment m Underwriters Laboratories UL Classification UL safety Compliance This medical LCD monitor is U L Classified WITH RESPECT TO ELECTRIC SHOCK FIRE AND ME CHANICAL HAZARDS ONLY IN ACCORDANCE WITH UL 60601 1 CAN CSA C22 2 601 1 EEC Safety Compliance This medical LCD monitor unit meets the requirements of EN 60601 1 so as to conform to the Medical Device Directive 93 42 EEC general safety information Use 120V rating 5 15P type plug only in the U S This medical LCD monitor complies to the above standards only when used with
19. 01 1 respectively safety re quirements for medical electrical systems Any person who has formed a combination system is responsible for the system to comply with the requirements of IEC 60601 1 1 or clause 16 of the 3 Ed of IEC 60601 1 respectively If in doubt contact qualified technician or your local representative Warning To avoid risk of electric shock this equipment must only be connected to a supply mains with protective earth Power supply AC DC Adapter is specified as a part of the LCD Color Display Do not to position equipment so that it is difficult to disconnect the power cord plug from the appliance inlet Warning Do not modify this equipment without authorization of the manufacturer 6 English FSN1966 2 2015 On installation 1 Openingsin the medical LCD monitor cabinet are provided for ventilation To prevent over heating these openings should not be blocked or covered If you put the medical LCD moni tor in a bookcase or some other enclosed space be sure to provide adequate ventilation 2 Putyour medical LCD monitor in a location with low humidity and a minimum of dust 3 Donot expose the medical LCD monitor to rain or use it near water in kitchens near swim ming pools etc If the medical LCD monitor accidentally gets wet unplug it and contact an authorized dealer immediately You can clean the medical LCD monitor with a damp cloth if necessary but be sure to unplug the medical LCD monitor first
20. 1 BRIGHTNESS Increases or decreases the brightness Range 0 100 2 CONTRAST Increases or decreases the contrast Range 0 100 3 CLOCK Increases or decreases the sampling frequency Range 0 100 4 PHASE Increases or decreases the phase level Range 0 100 5 BACKLIGHT Adjusts backlight dimming level Range 0 100 6 AUTO ADJUST fits to the most appropriate screen on the D SUB Analog RGBs signal Submenus under the COLOR TEMP menu 1 MODE Changes the color mode C1 C2 USER 2 RED Red balance Only works with USER mode Range 0 100 3 GREEN Green balance Only works with USER mode Range 0 100 4 BLUE Blue balance Only works with USER mode Range 0 100 Submenus under the IMAGE menu 1 IMAGE SIZE Changes the image size FULL FILL ASPECT 1 1 NORMAL 2 H POSITION Adjusts the horizontal position of the displayed source image Range 0 100 3 V POSITION Adjusts the vertical position of the displayed source image Range 0 100 4 GAMMA Adjusts GAMMA value VIDEO BYPASS 1 8 2 0 2 2 2 4 2 6 PACS 5 FILTER Sets the sharpness of image Softest Soft Normal Sharp Sharpest 6 OVER SCAN Adjusts the displayed size 0 8 7 IMAGE SETTING Changes the image setting Preset 1 2 User 1 2 3 8 ZOOM PAN Enlarges the image moves images left and right 9 FREEZE Keeps the image still Submenus under the SETUP menu 1 LANGUAGE Changes the OSD language 8 languages 2 OSD COLOR Adju
21. E YPbPr RGBS CVIDEO SVIDEOS O supported X not supported O supported up to UXGA 60Hz 162MHz Changes the size of the sub window when using PIP mode CAUTION DO not change input source sub Sub aspect ratio The PIP PIP SIZE aspect ratio depends on input timing Small 25 of panel size Large 33 of panel size Changes the on screen position of the PIP sub window to 1 of 9 locations PIP POSITION English 27 Main window FSN1966 2 2015 On Screen Display OSD System Overview continued Submenu Descriptions Function Description Swap main window and sub window contents in PIP PBP1 PBP2 Picture in picture PIP PIP SWAP Picture by Picture 1 PBP1 Picture by Picture 2 PBP2 lt gt Standard Signal Table p Horizontal Frequency Vertical Frequency Clock Frequency KHz MHz 28 English XXXX 51966 2 2015 Horizontal Frequency Vertical Frequency Clock Frequency KHz MHz 1280 x 1024 85Hz 91 146 85 024 157 500 1920 x 1080 60Hz 67 500 60 000 148 500 Signal Connector Pin Assignments VGA Interface Connector Pin No X oa o eno creer L eese ma DATA HORIZONTAL SY
22. EMP C2 Default 9300K color setting COLOR TEMP USER Default 7200K color setting value can be changed by user IMAGE SIZE DSUB DVI OPTICAL DVI DIGITAL input source FILL ASPECT NORMAL CAUTION FILL ASPECT NORMAL Size are dependant on input size ratio MAGE SIZE YPbPr RGBS SDI CVIDEO SVIDEO input source Ne gt 2 ANAMORPHIC FILL ASPECT NORMAL CAUTION FILL ASPECT NORMAL ANAMORPHIC Size are depend on input size ratio 24 English FSN1966 2 2015 continued isplay OSD System Overv On Screen D ions Submenu Descript Function Description Submenu Adjusts the horizontal position of the image This setting will return to the default state when executing AUTO ADJUST or RESET SETTINGS Adjusts the verticall position of the image This setting will return to the default state when executing AUTO ADJUST or RESET SETTINGS H POSITION V POSITION c c o o c o lt a gt ea gt o z o E gt o gt 5 o 2 a 5 o lt gamma value please refer to the panel specification gt gt gt gt gt gt gt gt gt gt gt gt gt 2222222222222 ac ac ac ac
23. Misty Multi Purpose Disinfectant Cleaner Misty Multi Purpose Disinfectant Cleaner 1 Zep Heavy duty glass amp all surface cleaner Klear Screen Screen TFT Kontakt Chemie Incidin Foam Ecolab Microzid Mild detergent Isopropyl alchohol with concentration 596 Household bleach generic sodium hypochlorite solutions of 5 2596 sodium hypochlorite diluted with water between 1 10 and 1 100 Precise Hospital Foam Cleaner Disinfectant 34 English XX 111966 2 2015 Thank you for choosing our product Service Please contact our customer service if you need any information or help with our products Warranty One year parts and labor EC Representative FORESEESON GmbH Industriestrasse 38a 63150 Heusenstamm Germany Tel 49 0 6104 643980 FORESEESON UK Ltd Unit 71 Barwell Business Park Leatherhead Road Chessington Surrey KT9 2NY UK Tel 44 0 208 546 1047 FORESEESON KOREA 404B Pangyoinnovalley B 253 Pangyo ro Bundang gu Seongnam si Gyeonggi do Korea 463 400 Tel 82 31 8018 0780 Fax 82 31 8018 0786 FORESEESON Shanghai Medical Equip Co Ltd Room 307 3F No 56 461 Hongcao Road Caohejing Development District Xuhui Shanghai 200233 Tel 86 21 6113 4188 FSN FORESEESON CUSTOM DISPLAYS INC 2210 E Winston Road Anaheim CA 92806 USA Tel 1 714 300 0540 Fax 1 714 300 0546 Specifications are
24. NC VERITICAL SYNC DDC CLOCK FSN1966 2 2015 mm English 29 Signal Connector Pin Assignments RS232C interface connector 1 5 ooooQ JE NoConnecion 9 NoConnecion DVI Input output interface connector Pin No Assignment Pinno Assignment TMDS ataz 13 No Connection imos Daan 3 oaa zasna 35 ND Lo oe mg _ 5 botta ms O 29 NoComecin s TMDS Data 1 21 No Connection TMS Data 1 22 TMDS Clock shield SDI interface connector 30 English 11966 2 2015 Signal Connector Pin Assignments continued Component RGBS YPbPr interface connector mm E RGBS YPbPr Fa GREEN 3 BLUE 4 HSync CSync V Sync No Connection R Pr 1 C Video interface connector wwe I mem 1 2 S Video interface connector Tn GND mw cord Indicator Equipotential earth terminal This should be connected to other equipment s earth terminal FSN1966 2 2015 English 31 Specification FS Y1901D Tm Power Consumption Front Side INPUT V PIP MENU POWER 1 x DVI D 1 x SDI SD HD 3G 1 x VGA Input Signal Video 1 x C VIDEO 1 x S VIDEO 1 x Component RGBS YPbPr 1x DVI D Output Signal Video 1 x SDI SD HD 3G
25. Small Large 4 POSITION Changes the PIP position 5 SWAP Swaps the position of the Primary and Secondary images 1966 2 2015 nmmnm M English 23 On Screen Display OSD System Overview Submenu Descriptions Function Description Quick Adjust Method Press the UP or DOWN W buttons BRIGHTNESS Or select BRIGHTNESS submenu and adjust with the PLUS and MINUS Setting the brightness too high or too low will decrease the amount of visible gray scales Quick Adjust Method Press the PLUS or MINUS buttons CONTRAST Or select CONTRAST submenu and adjust with the PLUS and MINUS Setting the contrast too high or too low will cause loss of some gray scales Do not adjust This setting will adjust automatically after auto adjustment When CLOCK frequency value is wrong the horizontal image may display incorrectly or picture noise may be present PHASE Do not adjust This setting will adjust automatically after auto adjustment When frequency value is wrong picture noise may be present BACKLIGHT Adjust backlight dimming level Setting the backlight too low will causes dark im age and too high will decrease the backlight lifetime AUTO ADJUST Fits to the most appropriate screen on the D SUB Analog signal SHARPNESS Adjusts the sharpness of a video image SATURATION Changes the color tone COLOR Changes the richness of color Range Green 0 50 Red 0 50 COLOR TEMP C1 Default 6500K color setting COLOR T
26. ac ac ac ec ac ec aaa 000000000000 2222222222222 zzzzzzzzzzzzz 5555555555559 Irrrrrrrrrrrr 00 00 00000000 Daaaaoaaaaaaai mmmmmmmmmmmmam C CC lt lt lt lt lt lt lt lt lt lt Adjusts the sharpness of a video image SHARPEST gt gt gt gt gt gt gt gt gt gt gt gt gt 5555555555555 n nutu wu wu lac ac ac ac ec ac ec ac aca ec loooocooooooooo aaa aaa looooooooooooo 2222222222222 5 A Irrrrrrrrrrrzr o 00000 000 00 0 uc uci uuu uu loaaaaaaaaaaaon loDDDOOOOOUOUU o mmm ml eo 10 maximum over scan of orignal input image Enables an 8 step TTT TI da aaaaaaaaaal 100000000000 22222222222 0222222222224 ILIIIIIIIIIIII Dooooo0000000 hu aaaaaaaad m mm mmm mm ac ac ec ac ac ac c ac
27. ast Range 0 100 3 BACKLIGHT Adjusts backlight dimming level Range 0 100 Submenus under the COLOR TEMP menu 1 MODE Changes the color mode C1 C2 USER 2 RED Red balance Only works with USER mode Range 0 100 3 GREEN Green balance Only works with USER mode Range 0 100 4 BLUE Blue balance Only works with USER mode Range 0 100 Submenus under the IMAGE menu 1 IMAGE SIZE Changes the image size FULL FILL ASPECT 1 1 NORMAL 2 Adjusts GAMMA value VIDEO BYPASS 1 8 2 0 2 2 2 4 2 6 PACS 3 FILTER Sets the sharpness of image Softest Soft Normal Sharp Sharpest 4 OVER SCAN Adjusts the displayed size 0 8 5 IMAGE SETTING Changes the image setting Preset 1 2 User 1 2 3 6 ZOOM PAN Enlarges the image moves images left and right 7 FREEZE Keeps the image still Submenus under the SETUP menu 1 LANGUAGE Changes the OSD language 8 languages 2 OSD COLOR Adjusts the OSD background from white opaque to translucent 3 OSD POSITION Changes the OSD position 9 Positions 4 DURATION Adjusts the length of time the OSD Menu is present on the screen 5 10 20 30 60 90 120 180 240 seconds 5 RESET SETTINGS Changes all the OSD values to factory default 6 AUTO SOURCE SELECT Disables or enables auto source select ON Searches through all possible input sources until an active video source is found OFF Video input is manually selected 7 INACTIVE INPUT Change the
28. bPr 8 PICTURE DELAY Adjust the picture delay 0 Disable deinteracer engine 1 Enable deinteracer engine Submenus under the PIP menu 1 LAYOUT Changes the layout OFF PIP PBP1 PBP2 2 SOURCE Changes the secondary source 3 SIZE Changes the PIP size Small Large 4 POSITION Changes the PIP position 5 SWAP Swaps the position of the Primary and Secondary images 22 English 111966 2 2015 Submenus for the following signal types SDI After selecting a main menu category press the button to enter the associated submenus as shown below Next use the UP and Down V buttons to navigate to the desired submenu then adjust as needed with the buttons Select the MENU button to exit from the submenu or main menu Submenus under the ADJUST menu 1 BRIGHTNESS Increases or decreases the brightness Range 0 100 2 CONTRAST Increases or decreases the contrast Range 0 100 3 SATURATION Changes the tone of color Range 0 100 4 COLOR Changes the richness of color Range green 0 50 red 0 50 5 BACKLIGHT Adjust backlight dimming level Range 0 100 Submenus under the COLOR TEMP menu 1 MODE Changes the color mode C1 C2 USER 2 RED Red balance Only works with USER mode Range 0 100 3 GREEN Green balance Only works with USER mode Range 0
29. bile RF communications equipment transmitters and the medical LCD monitor as recommended below according to the maximum output power of the communications equipment Separation distance according to frequency of transmitter m 150kHz to 80MHz 80MHz to 800MHz 800MHz to 2 5GHz Rated maximum 3 5 output power W 1 V1 3Vrms E1 3V m Ee ze of transmitter 3 6872 0 7375 11 6600 23 333 For transmitters rated at a maximum output power not listed above the recommended separation dis tance d in meters m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer Note 1 At 80 MHz and 800 MHz the separation distance for the higher frequency range applies Note 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by ab sorption and reflection from structures objects and people 1966 2 2015 m English 13 Parts Monitor FS Y1901D Accessories gt lt User Manual AC DC Adaptor AC Power Cord DVI D Cable JMW190KB1200F04 6ft 1 8 m US UK EU China 6ft 1 8m 6 23ft 1 9m Hospital Grade A A BNC Cable D SUB Cable S Video Y C Cable Screw BH M4 x 10 6ft 1 8m 6ft 1 8m 6ft 1 8m available for purchase available for purchase 14 English FSN1966 2 2015 Connectors
30. ble input sources until an active video source is found OFF Video input is manually selected 7 INACTIVE INPUT Change the input source between RGBs and YPbPr 8 PICTURE DELAY Adjust the picture delay 0 Disable deinteracer engine 1 Enable deinteracer engine Submenus under the PIP menu 1 LAYOUT Changes the layout OFF PIP PBP1 PBP2 2 SOURCE Changes the secondary source 3 SIZE Changes the PIP size Small Large 4 POSITION Changes the PIP position 5 SWAP Swaps the position of the Primary and Secondary images English 21 Submenus for the following signal types S VIDEO C VIDEO After selecting a main menu category press the button to enter the associated submenus as shown below Next use the UP and Down V buttons to navigate to the desired submenu then adjust as needed with the and buttons Select the MENU button to exit from the submenu or main menu Submenus under the ADJUST menu 1 BRIGHTNESS Increases or decreases the brightness Range 0 100 2 CONTRAST Increases or decreases the contrast Range 0 100 3 SHARPNESS Adjusts the sharpness of video image Range 0 100 4 SATURATION Changes the tone of color Range 0 100 5 COLOR Changes the richness of color Range green 0 50 red 0 50 6 BACKLIGHT Adjust backlight dimming level Range 0 100 Submenus under the COLOR TEMP menu 1 MODE Changes the color mode C1 C2 USER 2 RED Red balance Only works with USER mode
31. ending on the active input signal See the Controls section for a complete description of each OSD button 1 Enter the OSD RP To activate the OSD menu press the MENU y 5 button on the front of the display monitor close the OSD menu press the menu button to lr ENU POWER exit from the main menu or a sub menu 2 Pick a Main Menu Category After entering the OSD use the UP and Down W buttons on the front of the display monitor to navigate to a main menu category or The ADJUST menu controls brightness contrast and more The COLOR SETTING menu controls customized color settings El The IMAGE menu controls horizontal vertical positioning and sharpness BJ The SETUP menu controls language OSD behavior and more The PIP menu controls picture in picture layouts 3 Pick a Submenu Category After using the UP and Down W buttons to navigate to the desired main menu category press the button to enter the submenus associated with the selected main menu 18 English FSN1966 2 2015 Submenus for the following signal types VGA Analog RGB After selecting a main menu category press the button to enter the associated submenus as shown below Next use the UP and Down V buttons to navigate to the desired submenu then adjust as needed with the and buttons Select the MENU button to exit from the submenu or main menu Submenus under the ADJUST menu
32. l LCD monitor emits smoke or abnormal odor If the medical LCD monitor fails to operate in accordance with the operating instructions Accessories Use only accessories specified by the manufacturer or sold with the medical LCD monitor Classification Protection against electric shock Class including AC DC Adapter Applied Parts No Applied Parts Degree of safety in the presence of flammable anesthetics mixture with air or with oxygen or with nitrous oxide Not suitable for use in the presence of a flammable anesthetics mixture with oxygen or with nitrous oxide Mode of operation Continuous 1966 2 2015 I QE English 9 FCC Information This medical LCD monitor unit has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reason able protection against interference This monitor can radiate radio frequency energy and if not installed and used in accordance with the instructions it may interfere with other radio com munications equipment There is guarantee that interference will not occur a particular installation If this equipment is found to cause harmful interference to radio or television recep tion the user is encouraged to try to correct the interference by carrying out one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the di
33. l LCD monitor should assure that it is used in such an environment The medical LCD monitor uses RF energy only for its internal function Therefore its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment RF Emissions CISPR 11 RF Emissions The medical LCD monitor is suitable for use in all establish Harmonic emissions ments including domestic establishments and those directly IEC 61000 3 2 connected to the public low voltage power supply network that supplies buildings used for domestic purposes IEC 61000 3 3 2 Guidance and manufacturer s declaration electromagnetic immunity This medical LCD monitor is intended for use in the electromagnetic environment specified below The customer or the user of the medical LCD monitor should assure that it is used in such an environment Immunity test IEC 60601 Test Electromagnetic environment guidance level level Electrostatic 6 kV contact 6 kV contact Floors should be wood concrete or discharge ESD 8 kV air 8 kV air ceramic tile If floors are covered with IEC 61000 4 2 synthetic material the relative humidity should be at least 3096 Electrical fast 2 kV for power 2kVforpower Main power quality should be that of a typical transient burst supply lines supply lines commercial or hospital environment IEC 61000 4 4 1 kV for input 1 kV for input output lines output lines Surge 1kV differential mode 1kV differential mode Main
34. power quality should be that of a typical IEC 61000 4 5 2 kV common mode 2 common mode commercial or hospital environment Portable and mobile RF communications equip ment should be used no closer to any part of the LCD monitor including cables than the recommended separation distance calculated from the equation applicable to the frequency 3Vrms 3Vrms of the transmitter 150 kHzto 150 kHzto Recommended separation distance d 80MHz 80MHz ae d vP LZ Conducted RF IEC 61000 4 6 Where P is the maximum output power rating of the transmitter in watts W 1966 2 2015 English 11 3 Guidance and manufacturer s declaration electromagnetic immunity This medical LCD monitor is intended for use in the electromagnetic environment specified below The customer or the user of monitor should assure that it is used in such an environment Immunity test IEC 60601 Test Compliance level Electromagnetic environment guidance level Power frequency 50 60 Magnetic field IEC 61000 4 8 Voltage dips short Interrup tions and voltage variations on power supply input lines IEC 61000 4 I 1 Radiated RF IEC 61000 4 3 12 English 3 0 A m 596 Ut 29596 dip in Ur for 0 5 4096 Ur 6096 dip in UT for 5 cycle 70 Ut 3096 dip in Ut for 25 cycle lt 5 Ut 9596 dip in Ut for 5 sec 3V m 80 0 MHz to 2 5 GHz 596 Ut 9596 dip in for 0 5 cycle 4096 Ut 6096 dip in
35. se level Range 0 100 Submenus under the COLOR TEMP menu 1 MODE Changes the color mode C1 C2 USER 2 RED Red balance Only works with USER mode Range 0 100 3 GREEN Green balance Only works with USER mode Range 0 100 4 BLUE Blue balance Only works with USER mode Range 0 100 Submenus under the IMAGE menu 1 IMAGE SIZE Changes the image size FULL FILL ASPECT 1 1 NORMAL 2 H POSITION Adjusts the horizontal position of the displayed source image Range 0 100 3 V POSITION Adjusts the vertical position of the displayed source image Range 0 100 4 GAMMA Adjusts GAMMA value VIDEO BYPASS 1 8 2 0 2 2 2 4 2 6 PACS 5 FILTER Sets the sharpness of image Softest Soft Normal Sharp Sharpest 6 OVER SCAN Adjusts the displayed size 0 8 7 IMAGE SETTING Changes the image setting Preset 1 2 User 1 2 3 8 ZOOM PAN Enlarges the image moves images left and right 9 FREEZE Keeps the image still Submenus under the SETUP menu 1 LANGUAGE Changes the OSD language 8 languages 2 OSD COLOR Adjusts the OSD background from white opaque to translucent 3 OSD POSITION Changes the OSD position 9 Positions 4 DURATION Adjusts the length of time the OSD Menu is present on the screen 5 10 20 30 60 90 120 180 240 seconds 5 RESET SETTINGS Changes all the OSD values to factory default 6 AUTO SOURCE SELECT Disables or enables auto source select ON Searches through all possi
36. stance between the medical LCD monitor and the subject of interference 3 Plug the monitor into an outlet on a different electrical circuit than that to which the subject of interference is connected 4 Consult the dealer or an experienced radio TV technician for help NOTICES TO USER This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interfer ence received including interference that may cause undesired operation FCCWARNING This medical LCD monitor generates or uses radio frequency energy Changes or modifications to this medical LCD monitor may cause harmful interference unless the modifications are ex pressly approved in the instruction manual The user could lose authority to operate this equip ment if an unauthorized change or modification is made PRODUCT LIFETIME The average lifespan of this LCD monitor has been determined to be approximately 5 years con sidering the LCD flat panel which has been specified with a lifetime of 50 000 hours 10 English X X 111966 2 2015 1 Guidance and manufacturer s declaration electromagnetic emission The medical LCD monitor is intended for use in the electromagnetic environment specified below The customer or the user of the medica
37. sts the OSD background from white opaque to translucent 3 OSD POSITION Changes the OSD position 9 Positions 4 DURATION Adjusts the length of time the OSD Menu is present on the screen 5 10 20 30 60 90 120 180 240 seconds 5 RESET SETTINGS Changes all the OSD values to factory default 6 AUTO INPUT SELECT Disables or enables auto source select ON Searches through all possible input sources until an active video source is found OFF Video input is manually selected 7 INACTIVE INPUT Change the input source between RGBs and YPbPr 8 PICTURE DELAY Adjust the picture delay 0 Disable deinteracer engine 1 Enable deinteracer engine Submenus under the PIP menu 1 LAYOUT Changes the layout OFF PIP PBP1 PBP2 2 SOURCE Changes the secondary source 3 SIZE Changes the PIP size Small Large 4 POSITION Changes the PIP position 5 SWAP Swaps the position of the Primary and Secondary images FSN1966 2 2015 English 19 Submenus for the following signal types DVI After selecting a main menu category press the button to enter the associated submenus as shown below Next use the UP and Down V buttons to navigate to the desired submenu then adjust as needed with the and buttons Select the MENU button to exit from the submenu or main menu Submenus under the ADJUST menu 1 BRIGHTNESS Increases or decrease the brightness Range 0 100 2 CONTRAST Increases or decreases the contr
38. subject to change with or without notice SASSI Fse us FC CE FSN www fsnmed com 5 d co Medical Technologies
39. the supplied medical grade power supply FS Y1901D JMW190KB1200F04 Caution Make sure the power cord is the correct type that is required in your area This medical LCD monitor has a universal power supply that allows operation in either 100 120V AC or 200 240V AC voltage areas no user adjustment is required Use the proper power cord with correct attachment plug type If the power source is 120 V AC use a power cord which is a Hospital Grade Power Cord with NEMA 5 15 style plug labeled for 125 volts AC with UL and C UL approvals If the power source is a 240 V AC supply use the tan dem T blade type attachment plug with ground conductor power cord that meets the respec tive European country s safety regulations 8 English XXX X 11966 2 2015 The hospital grade plug for medical products intended for use Denmark has DEMKO approval and is rated 13 amps at 250Vac Plug is recommended for use in medical applications and specifica tions are being added to the standard SB 107 2 D1 Plug mates with maker s Danish hospital grade socket Hospital sockets have slightly different shaped openings allowing only the hospital plug not the standard Danish plug to be inserted to protect the ac circuit in specific medical settings A ground post located on the back of the display may be used for the purpose of grounding the display s chassis
40. tor Doing so may create the danger of electric shock 3 Toreduce the risk of electric shock do not remove cover No user serviceable parts inside Only a qualified technician should open the case of the medical LCD monitor 4 Never use your medical LCD monitor if the power cord has been damaged Do not allow anything to rest on the power cord and keep the cord away from areas where people can trip over it 5 Besureto hold the plug not the cord when disconnecting the medical LCD monitor power cord from an electric socket 6 Unplug your medical LCD monitor power cord when it is going to be left unused for an ex tended period of time 7 Unplug your medical LCD monitor power cord from the AC outlet before any service 8 If your medical LCD monitor does not operate normally in particular if there are any unusual sounds or smells coming from it unplug it immediately and contact an authorized dealer or service center 9 Please contact the manufacturer if the set should be installed in an inaccessible area Warning Do not touch input or output connectors and the patient simultaneously Warning This medical LCD monitor is intended for connection to input output signals and other connectors that comply with relevant IEC standard e g IEC60950 for IT equipment and IEC60601 series for medical electrical equipment In addition all such combination system shall comply with the standard IEC 60601 1 1 or clause 16 of the 3 Ed of IEC 606
Download Pdf Manuals
Related Search