Delta .68 - Wolfpack Paintball Team
Contents
1.2. D Valve Cap 21 Gas Clamp Screw 22 Grip Frame 23 Main Body 24 Grip Frame Screws 25 Safety Assembly 26 Trigger Plate 27 Sear 28 Sear Spring 29 Valve Face Seal O Ring 30 Grip Frame Pin Set eee DELTA 68 PAINTBALL MARKER D gt DELTA 68 Loading Paintballs The performance of your marker is directly affected by the quality of paintballs used We highly recommend Diablo paintballs to give you satisfaction and success on the playing field 1 Confirm that the Barrel Plug is properly installed and the marker in on Safe 2 Push forward the pin on the side of the feed tube to the front and lock down the spring latch 3 Point the marker into a safe direction and remove the plug on the rear of the feed tube Now proceed to load paintballs individually into the Feed Tube Be sure to leave room for the plug 4 Place plug back into the feed tube and ensure it is secure in place before unlatch ing the Feed Tube spring Chronographing Never operate your marker without first checking the velocity and confirming that you are firing below that required on the field of play At no time should the marker fire paintballs in excess of 300 feet per second Higher velocities are not only potentially dangerous they often result in a substantial increase in paintballs broken in the marker 1 Confirm that the Barrel Plug is properly installed and the marker is on Safe 2 Using a hex key not included make sur
3. Sanne This lightweight assault paintball pistol is custom milled from high grade aluminum for superb bal ance and precision The compact construction of this competition paintball pistol will give you a mobile edge in the heat of battle In competition training or back yard fun this paintball pistol will give you safe and reliable paint ball play Paintball Pistol AWARNING This is NOT a toy Misuse may cause serious injury or death Eye protection designed for paintball use must be worn by user and any person within range Recommended at least 18 years old to purchase 14 years old to use with adult supervision or 10 years old to use on a paintball field meeting ASTM standards F177797 Read Operation Manual before using USER MANUAL eee DELTA 68 PAJNTBALL MARKER A WARNING Thisis nota toy Misuse may cause serious injury or death Eye protection designed specifically for paintball must be wom by the user and persons within range Recommend 18 years of age or older to purchase Persons under 18 years of age must have adult supervision READ OWNER S MANUAL BEFORE USING Rules of Safe Marker Handling 1 2 10 11 12 13 Treat every marker as if it were loaded Never look down the barrel of a paintball marker Keep your finger off the trigger until ready to shoot Never point the marker at anything you don t wish to shoot Keep the marker on safe until read
4. plunger on the front of the Gas Clamp 19 with your finger Fe ccc eo 6 Point the marker downward and in a safe direction 7 Swiftly force down the gas clamp all the way puncturing the 12g CO2 cartridge The marker is now gassed and ready to operate ok Attaching Feed Tube 1 Confirm that the Barrel Plug is properly installed on the marker and is on Safe 2 Taking the feed tube hook on the back retaining stud on the body of the Delta 68 23 Pulling back the front retaining stud clip into place See Diagram below Installing the feed tube _ Removing the feed tube A k 1 Hook retaining stud _ 1 Pull back retaining stud and un clip from 2 Pull back retaining stud the seat and clip into place eee DELTA 68 PAJNTBALL MARKER Sone 14 23 oe PT 16 1 Li 20A 206 21 fo H Terns 20D i 1 29 16 y Aii 16 i Delta 68 Parts List 1 Hammer Main Spring Recoil Pad Velocity Adjuster A Spring Strut B Hammer Plug fe OOS Air Plate Screws 5 6 Valve Stop Pin 7 Gas Valve 8 Cupseal 9 Valve Spring 10 Valve Gas Plug 11 Gasket 12 Air Transfer Plate 13 Quick Release Pin w R Clip 14 Bolt 15 Metal Ball Detent 16 Multi Use O Ring 17 Wrap Around Grip Panels 18 Grip Panel Screws 19 Gas Clamp 20 Valve Face A Pressure Spring B Piercing Pin C Air Filter
5. position Point the marker in a safe direction Lock forward the feed tube spring in preparation for unloading Open the feed tube plug on the back of the marker and remove all the paintballs from within the Feed Tube Remove the Feed Tube from the top of the marker Take the Barrel Plug out of the marker and face the marker into a safe direction NOTE There may still be a ball in the chamber Make sure you are in a safe area to fire the marker safely 7 Fire the marker until it runs out of CO2 NOTE When the marker un cocks Re cock the marker and fire it repeatedly until the gun doesn t release any more air 8 Place your Barrel Plug back into your barrel and open the front Gas Clamp 19 by pushing it down and forward to release pressure on the 12 gram CO2 9 Remove the 12 Gram CO2 and dispose of it properly These cannot be reused ak WP O Maintenance WARNING All maintenance should be performed with an unloaded and degassed marker ONLY Bolt and Hammer 1 De gas the marker according to previous directions 2 Always perform maintenance over a smooth clean work surface This will help prevent the accidental loss of small parts 3 Make sure the bolt is in the forward position before proceeding 4 Remove the Quick Release Pin 13 5 Remove the Hammer Plug 4B from the rear of the Main Body 6 Pull the Bolt 14 from the rear This will also remove the Spring Strut 4A Main Spring 2 Recoil Pad
6. 3 and Hammer 1 7 Clean the Bolt thoroughly includes rinsing in warm water if needed Be sure to dry all parts well before the next step 8 Lubricate the Bolt and Hammer with non corrosive lubricant such as Empire Lube or Empire Oil 9 Place the Bolt s Connecting Pin into the hole on top of the Hammer and while pointing the marker downward Guide this assembly in to the rear of the Main Body 10 The Striker will likely stop when it makes contact with the top of the Sear 27 11 While putting slight pressure on the rear of the bolt pull the trigger this depresses the Sear and allows the Bolt Hammer assembly to travel forward 12 Return the Main Spring Recoil Pad and Spring Strut to their proper position following the schematic on Page 4 5 13 Place the Hammer Plug into the rear of the Main Body with the longest portion of the Main Spring Spring Strut 14 Push the Hammer Plug in and replace the Quick Release Pin eee DELTA 68 PAJNTBALL MARKER Sone Storage Always set the marker on Safe and remove the Feed Tube all paintballs and the propellant source Place the marker in a secure location where it cannot be accessed by unauthorized persons Troubleshooting Guide Symptom Does not Fire Leaks Air Down Barrel Leaks Air from where the 12 gram seats against the Valve Face Does not Re cock Goes Full Auto Excessive Ball Breakage Cause Not Cocked On Safe Out of Gas B
7. ad Cup Seal Not Cocked Bad Valve Face O Ring Low on Gas Bad Hammer or Hammer O Ring Needs Lubrication Debris Around Bolt Hammer Sear not catching Low on Gas Propellant Source Bad Hammer or Hammer O Ring Needs Lubrication Low Quality Paintballs Cure Cock the Bolt to the Rear Push Safety to Fire Replace 12 Gram CO2 Replace Reset Cupseal Cock the Bolt to the Rear Replace Valve Face O Ring Replace 12 Gram CO2 Replace Hammer O Ring or Hammer Lubricate Hammer Bolt Remove the Bolt Hammer and clean parts and breach Tighten Grip Frame Screws Replace 12 Gram CO2 Replace Hammer O Ring or Hammer Lubricate Hammer and Bolt Use better Paintballs such as Diablo brand When in doubt thoroughly clean and lubricate the marker Many marker function problems are caused by excessive dirt or lack of lubrication For further assistance go to www paintballsolutions com or call 1 800 220 3222 Warranty Registration To assist us in providing the best customer service possible and to increase your war ranty from 90 days to one year at no additional cost Complete and mail this to Paintball Solutions 570 Mantua Blvd Sewell NJ 08080 Or register online at www PaintballSolutions com Marker Type Delta 68 Name Address City State Zip Country Email Address Serial Number located on left side of marker Date of Purchase Place of Purchase
8. e the Velocity Adjuster 4 set screw is backed out without removing it 3 Make sure that you and anyone within range is wearing eye protection designed specifically for paintball While pointing the paintball marker in a safe direction remove the Barrel Plug and move the safety to the fire position Point the marker over the chronograph and in a safe direction Pull the trigger and observe the reading on the chronograph To increase the velocity turn the Velocity Adjuster 4 clockwise To decrease the velocity turn the Velocity Adjuster 4 counter clockwise Once the desired velocity has been reached use the hex key not included to turn the Velocity Adjuster 4 Set screw in until it binds against the Hammer Plug 4B This will prevent the Velocity Adjuster from moving during play and is required by most competitions and fields 10 Re install the Barrel Plug and place the marker on Safe 11 Proceed to the playing field 12 Keep the safety in the Safe position and the Barrel Plug in place until ready to play p gt oong De Gassing A NOTE Do NOT remove a 12 Gram CO2 unless it is completely empty The 12 Gram CO2 can become a projectile if not completely empty Failure to do so will crack and dry out the o rings inside the marker causing a leak Make sure that you and anyone within range is wearing eye protection specifically designed for paintball Set the safety in the Safe
9. ically be extended for an additional year Numbers shown in parentheses following part names correspond to the numbers on the Parts key located on the centerfold pages of this manual Initial Assembly 1 Place a Barrel Plug into the end of the barrel The barrel is the top chamber of the Main Body 23 2 Push the safety 25 into the safe position pushing from left to right looking down the sights Attaching Propellant Source 1 Confirm that the Barrel Plug is properly installed and the marker is on Safe 2 Cock the marker by pulling the Bolt 14 in the rearward direction until it clicks into place This compresses the Main Spring 2 and allows the Cupseal 8 to properly seat 3 Place a few drops of non corrosive lubricant made specifically for use in paintball Empire Oil into the center of the bottom chamber of the Main Body 23 where the CO2 will be punctured This must be done for every 12 Gram CO2 put into the marker This will run the oil through the valve to ensure the puncture O Rings stay moist and do not dry or crack Failure to do so will cause the marker to leak Place the 12 Gram CO2 cylinder into the tube with the narrow end in first Lower the clamp down so the lever is at a 45 degree angle when the plunger makes contact with the 12 gram CO2 but doesn t puncture it See Diagram Below If it doesn t touch or touches earlier you may have to remove the 12 gram and screw in or back out the
10. sn t everything it sure beats the alternative Play Hard play safe play to win WARRANTY INFORMATION Standard Warranty The manufacturer warranties to the original customer that this product is free from defects in material and workmanship under normal use and service for a period of 90 days from the original date of purchase by the initial owner purchaser The manufactur er agrees to repair or replace at its discretion any product within a reasonable period of time This warranty does not cover o rings scratches nicks normal wear and tear of parts any modifications or normal fading of anodizing or damage caused by dropping or hitting of the product This warranty shall not apply if it is shown by the manufacturer that the consumer caused the defect or malfunction because of misuse This warranty only covers original factory parts Any modifications or tampering of original factory parts will not be covered by this warranty Warranty work can only be conducted by the manufac ture technicians and or authorized technicians If product needs to be repaired package it carefully and send it together with your name address phone number and a brief description of the malfunction to Paintball Solutions 570 Mantua Blvd Sewell NJ 08080 Extended Warranty By returning the enclosed warranty registration card or registering your warranty on line at www PaintballSolutions com within fifteen days of purchase the warranty will auto mat
11. y to shoot Keep the barrel blocking device in on the marker s muzzle when not shooting Always remove paintballs and propellant source before disassembly After removing propellant source point marker in safe direction and discharge until marker is degassed Store the marker unloaded and de gassed in a secure place Follow warnings listed on propellant source for handling and storage Do not shoot at fragile objects such as windows Every person within range must wear eye face and ear protection designed specifically to stop paintballs and meeting ASTM standard F1776 Always measure your marker s velocity before playing paintball and never shoot at velocities in excess of 91 44 meters 300 feet per second C TABLE OF CONTENTS Page Topic s DELTA 68 Welcome Warranty Information Initial Assembly Attaching Propellant Source Attaching Feeder Hopper Exploded Diagram Parts Key Loading Paintballs Chronographing De Gassing Maintenance Storage Troubleshooting Guide Warranty Registration O DELTA 68 PAINTBALL MARKER D gt DELTA 68 Welcome Thank you for purchasing this Delta 68 Paintball marker The Delta 68 represents the culmination of a great deal of research by Psychoballistics along with input from players such as you We believe that the affordability of a reliable feature packed marker will improve your playing experience and winning percentage While winning i
Download Pdf Manuals
Related Search