Manual Transmission Clutch Adaptor for 3-drive・AC manual
Contents
1. Affix the male sleeve to the places as product s wire Turn back the tip of the wires one 10 mm e Ve Wrap around both wire Connect the male connector to the end X After connecting the male and female coils XWhen crimping please of the cable connectors make sure to firmly twist the use crimpers or use Male Connector male sleeve inside the female sleeve pliers to bend and then ra mm solder together SS n Connecting The Wires Connect to the Clutch Switch Signal Common for both THA MA1 and THA MA2 After confirming the connection position for your model car as shown on the attached sheet Wiring Chart MT connect the Brown or wire using one of the supplied cut connectors X Some models may have two clutch switches please connect to the same connector as listed under Connector Design in the Wiring Chart MT Refer to Reference 2 How to use the Cut Connectors Ea customers using THA MA1 make sure to insulate the wire Brown A or Green left unconnected e g HONDA CIVIC Wiring Chart MT x 7 HS PATR ARIR AIK ES mE TAAR P 4 Wire Color HONDA Sty7 THA mat MTC 2 Bon m n Clutch i ee Switch Connector ile Brown r M2. TC 2 Wire leading from product 2 Connect for Adaptor Power For THA MA1 Using one of the supplied cut connectors connect the wire of the Adaptor to the GE wire of the 3 drive AC For THA MA2 Using one of the supplied cut connectors connect the wire of the Adaptor to the clutch switch IGN wire 12V with key ON Installing The Product Please be sure to bundle away A all wires with tape etc While in use if wires become free they may interfere with driving and cause accidents Also wires which are smashed or crushed may result in a short and can be extremely dangerous As shown in the diagram below use the double sided tape included to fasten the units into positions not usually affected by water Example of Installation Under the steering column cover Ba Ww How to Install Double sided tape Included Clean to remove low positions oil and dust HEA 3 Connect to the Brake Switch Signal Common for both THA MA1 and THA MA2 Cut the wire of the 3 drive AC at an appropriate place Using the supplied connectors attach the female connector to the brake switch wire and the male connector to the 3 drive AC wire gt Refer to Reference 1 How to use the Connectors 3 drive AC Female Connector Male to Brake Connector Switch Connect the wire and the wire from the adaptor to the just at
3. cdh A A As of June 2010 No 1 U S ER S MAN UAL Manual Transmission Clutch Adaptor for 3 drive AC This product is a Manual Transmission Clutch Adaptor specifically designed for use with our 3 drive AC products CAUTION Improper use or disregard of these warnings NOTE Improper use or disregard of these warnings may cause may result in the injury or death of people injury to persons damage the product and or other things Do not use in conjunction with products from other manufacturers When installing this product we recommend that if technical knowledge In such a case PIVOT Corporation accepts no responsibility in any becomes necessary please consult a qualified mechanic manner whatsoever for any damage or trouble direct or indirect PIVOT accepts no responsibility whatsoever direct or indirect for any lf the product is not installed properly it may result in poor operation troubles that may occur if this product is modified or used in conjunction including that the product does not work or the Auto cruise function with another company s product does not run properly Do not use electrotap Please check the contents of the package o S ES A D R Cut Male Connector Female Connector Double sided User s Manual Wiring Chart MT Zip Tie Tape i Connectorsx 3 Male Sleeve Female Sleeve 25x35 mm This Book in Japanese If the clutch switch wiring ha
4. or there Please reconfirm whether wiring and connections are correct or not AUTO CRUISE is automatically deactivated and the display switches to throttle controller is a poor connection Each wire may have been improperly wired or there Please reconfirm whether wiring and connections are correct or not The clutch pedal is pressed down The clutch pedal is not fully pressed down all the way Make sure to press down fully on the clutch pedal but Auto Cruise does not deactivate wired or there is a poor connection he or Green wires may have been improperly Please reconfirm whether wiring and connections are correct or not PIVOT CORPORATION 87 3 Shimookada Okada Matsumoto shi Nagano 390 0313 Japan TEL0263 46 5901 http pivotjp com
5. s been changed in any way to connect to a different product make sure to return it to its original condition A Basic Wiri ng X For details about the connection position for the clutch switch signal please see the attached sheet Wiring Chart MT THA MA1 Clutch THA MA2 Switch Signal Brown o Green Yellow Ke c Brown H Clutch Clutch Clutch Adapter Adapter Switch Signal gt Red Gray Purple Vy Gray Purple fe Earth Black x Clutch Clutch gt Pedal Pedal 3 drive AC mM to Brake 3 drive AC to Brake Red Switch Switch X Use Connector included Ml Use Cut Connector included foi KI Use Connector included Ml Use Cut Connector included Reference 1 How to use the Connectors Figure is shown using a male connector Reference 2 How to use the Cut Connectors Pull the cable through the male sleeve Crimp down with crimpers to make sure that Peel off of the vinyl Close tightly with cut Male sleeve f the inner wires are firmly connected to the cover at connection connector Z e inner part of the connector and that the Hoa gt 50 cable section is connected to the outer part 10 mm of the connector gt a Remove about 10 mm of the cable Crimp an a casing P 10 mm CH Peel off of the vinyl Insulate with vinyl tape FE tT cover at the end of the
6. tached connectors Clutch Adapter 3 drive AC on to Brake Switch 4 Connect for Earth Common for both THA MA1 and THA MA2 Using one of the supplied cut connectors connect the wire of the Adaptor to the GEE wire of the 3 drive gt AC Refer to Reference 2 How to use the Cut Connectors A After installation make sure to carry out INITIAL SETTINGS and Speed Pulse Settings Make sure to carry out all Initial Settings and Speed Pulse Settings by following directions shown on pages 7 and 8 of the 3 drive AC User s Manual If these settings are not carried out the product will not run properly After having fully read sections Basic Operation and How to Operate found on pages 8 to 11 of the 3 drive AC User s Manual take a test drive as described on page 11 Test Drive If while in Auto Cruise pressing down on the clutch pedal deactivates the Auto Cruise function the adaptor is working properly VAN Usage Note In some car models it is necessary to fully press down on the clutch to activate the clutch switch signal When deactivating Auto Cruise make sure to fully depress the clutch Pushing down only half way will cause the engine rpm to increase Troubleshooting Trouble Possible Causes Possible Solutions AUTO CRUISE does not Operate is a poor connection Each wire may have been improperly wired
Download Pdf Manuals
Related Search