Gyro LED User Manual ()
Contents
1. CAUTION Please read and understand these instructions before installing or operating this unit Introduction The Gyro LED is a 7 channel DMX intelligent scanner unit The Gyro LED has 3 operating modes sound active mode auto program mode or it can be controlled by a DMX controller The unit can be run as a stand alone unit or in a Master Slave configuration This unit has been tested at the factory there is no assembly required The unit is ready to be plugged in to a power outlet To enhance the beams effects you can use a fog machine This unit looks good in pairs CAUTION Please read and understand these instructions before installing or operating this unit Fuse Replacement Locate and remove the unit s power cord Once the cord has been removed located the fuse holder located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder has a built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse Eliminator Los Angeles CA SPECIFICATIONS Model LED Weight Size Fuse Power Consumption Supply Voltage Working Position Duty Cycle DMX Channels Gobos Colors Warranty Gyro LED 1 x 25W LED 9 4lbs 4 3kgs 12 75 H x 6 W x 5 L 2 Amp 50W 110V 240V 50 60Hz Any Safe position None 7 DMX Channels 11 plus Spot 8 Colors2. White 1 Year wwwi EliminatorLighting com MENUS To access these menus you must press the ESC button twice and then press the UP or DOWN buttons until you find the specific menu you are looking for ADDR At this menu you can set the DMX address Press the Enter button and the A will start flashing Press the UP or Down buttons to find your desired address When you have found your desired address press the Enter button to set it SOUN Sound Active In this menu you can activate Sound Active mode Using the Up button scroll to SOUN and press Enter Either MAST Master in sound mode or ALON Stand Alone unit in sound mode will be displayed Use the Up and Down buttons toggle between the two modes and press Enter to make your selection AUTO Auto Program In this menu you can activate the auto program mode Using the Up or Down buttons scroll to AUTO and press Enter Either MAST Master in Auto mode or ALON Stand Alone unit in Auto mode will be displayed Use the Up and Down buttons toggle between the two modes and press Enter to make your selection RPAN Reverse Pan In this menu you can reverse the Pan function Using the Up button scroll to RPAN and press Enter Press the Up button until On is displayed and press Enter This func tion works better when you have two units connected in a Master Slave setup Have one unit set to reverse Pan and the other unit left in norma
3. ALL MOTOR RESET 100 119 INTERNAL PROGRAM 1 120 139 INTERNAL PROGRAM 2 140 159 INTERNAL PROGRAM 3 160 179 INTERNAL PROGRAM 4 180 199 INTERNAL PROGRAM 5 200 219 INTERNAL PROGRAM 6 220 239 INTERNAL PROGRAM 7 240 255 INTERNAL PROGRAM 8 www EliminatorLighting com
4. ect your DMX Controller Use the controller s faders to control the various DMX fixture traits For longer cable runs more than a 100 feet use a terminator on the last fixture For help operating in DMX mode consult the manual included with your DMX controller AO Qe N gt Eliminator Los Angeles CA www EliminatorLighting com MASTER SLAVE OPERATION SOUND ACTIVE OR AUTO MODE This function will allow you to link up to 16 units together and operate without a controller The units can be sound activate or run in a auto mode In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 This is a very simple process Using standard XLR microphone cables daisy chain your units together via the XLR connector on the rear of the units Remember the Male XLR connector is the input and the Fe male XLR connector is the output For longer cable runs we suggest a terminator at the last fixture 2 See Sound Active mode or Auto mode to select the Master option 1 Year Limited Warranty Eliminator Lighting warranty is valid from the date of purchase Our 1 year limited warranty covers manufacturing defects only Serial number place of purchase with dated valid receipt must be submitted at time of service Eliminator Lighting warranty does not cover items or parts prone to wear and tear motors fuses brushes and belts Elim
5. inator Lighting warranty is only valid with in the United States Eliminator Los Angeles CA www EliminatorLighting com DMX TRAITS 7 CHANNELS CHANNEL 1 CHANNEL 2 CHANNEL 3 0 13 14 27 28 41 42 55 56 69 70 83 84 97 98 111 112 127 128 190 191 255 CHANNEL 4 0 8 9 17 18 26 27 35 36 44 45 53 54 62 63 71 72 80 81 89 90 98 99 107 108 116 117 125 126 134 135 143 144 152 153 161 162 170 171 179 180 188 189 197 198 206 207 255 CHANNEL 5 0 9 10 19 20 127 128 137 PAN TILT COLOR WHEEL WHITE YELLOW PINK GREEN PURPLE BLUE LIGHT GREEN ORANGE RED RAINBOW CLOCKWISE ROTATION RAINBOW COUNTER CLOCKWISE GOBO WHEEL SPOT GOBO 1 GOBO 2 GOBO 3 GOBO 4 GOBO 5 GOBO 6 GOBO 7 GOBO 8 GOBO 9 GOBO 10 GOBO 11 GOBO 1 SHAKE GOBO 2 SHAKE GOBO 3 SHAKE GOBO 4 SHAKE GOBO 5 SHAKE GOBO 6 SHAKE GOBO 7 SHAKE GOBO 8 SHAKE GOBO 9 SHAKE GOBO 10 SHAKE GOBO 11 SHAKE GOBO WHEEL CLOCKWISE ROTATION SLOW FAST SHUTTER CLOSED OPEN STROBE EFFECT 1 SLOW FAST OPEN Eliminator Los Angeles CA CHANNEL 5 SHUTTER CONT 138 201 STROBE EFFECT 2 SLOW FAST 202 255 OPEN CHANNEL 6 MASTER DIMMER 0 255 0 100 CHANNEL 7 FUNCTIONS PROGRAMS 0 59 RESERVED 60 79 COLOR MOTOR amp GOBO MOTOR RESET 80 99
6. l Pan RTIL Reverse Tilt In this menu you can reverse the Tilt function Using the Up button scroll to RTIL and press Enter Press the Up button until On is displayed and press Enter This function works better when you have two units connected in a Master Slave setup Have one unit set to re verse Tilt and the other unit left in normal Tilt RDIS Display In this menu you can flip the display 180 Using the Up button scroll to RDIS and press Enter Either ON or OFF will now be displayed If you want to flip the display press the Up button so that ON is displayed and press Enter REST Reset In this menu you can activate reset function Using the Up button scroll to REST and press Enter The unit will now begin to reset LOAD In this menu you can activate reset function Using the Up button scroll to LOAD and press Enter The unit will now begin to reset UNIVERSAL DMX CONTROL This unit allows you to use any universal DMX 512 controller to control head movement the color wheel the gobo wheel and the shutter strobe A DMX controller allows you to create unique programs tailored to your individual needs Follow the set up specifications that are included with your DMX controller The Gyro LED is a 7 Channel DMX unit Press the Up or Down buttons until ADDR is displayed an press Enter Use the Up and Down buttons to find your desired address and press Enter Conn
Download Pdf Manuals
Related Search