User Manual - HeliPal.com
Contents
1. Note Channels must be supporting the transmitter 2 2 Auto Searching Confirm that the transmitter has entered a normal working condition Press to turn on the monitor press S MODE to select RF signal Long pressing gt CH Q Auto Searching will display on the top left corner of the screen means the machine start to auto scan When the screen on the upper left corner shows the BAND X CH X image displaymeans finished searching Now it can receive the signal 6 2 3 Manual channel scan and setting Confirm that the transmitter has entered a normal working condition Press to turn on the monitor press S MODE to select RF signal Press gt CH Q button BAND X CH X will display on the top left corner of the screen press S BAND button to switch BAND A B E F channels and then press CH Q button to select 1 8 channels If the transmitter has worked receiver and transmitter frequency in agreement the receiver will receive the signal sent from the transmitter and displayed on the monitor Note The effect of receiving the distance has a great relationship with the reception power of the transmitter and the receiver venues If the reception is poor the antenna can be replaced with three leaves four leaf antenna or panel antenna Replace the antenna should pay attention to the antenna and receiving the same frequency 3 Operation instru2. To adjust the OSD position in vertical X OSD Timeout To adjust the clock X Transparent To adjust the level of transparent EF unction 1920x1080 60HZ Reset Back to original setting x System No use in PC state Psouna X Volume To adjust the volume ln HDMI DVI VIDEO State W color In HDMI DVI VIDEO state color menu is different In HDMI State Brightness Contrast Hue Saturation Color Temp Brightness Contrast Saturation Color Temp Brightness Contrast Hue Saturation X Brightness To adjust the image brightness X Contrast To adjust the brightest and darkest ratio of the image please note the sense of picture when adjust proportion too large or small will make the picture lose the color of showy X Saturation To adjust color saturation X Hue To adjust the hue in NTSC mode or in HDMI or VIDEO Mode Color Temp OSD IN HDMI DVI mode the image s color Temp could be chosen and adjusted When select User It could be chosen R G B to adjust the corresponding analog value to meet the different user s requirement on the color of the image Language English H Position E 5 V Position 6S C50 OSD Timeout Off Transparent Off X Language To choose OSD language check below English fi 4 X Fran ais Italiano Deutsch Espanol H 5 ZAO Pycc Portugues X H Position To adjust the OSD position in horizontal X V Position To adjust the OSD position
3. 32 Channel Auto Searching Wireless FPV Monitor with Dual Receiver LCD Monitor lt BAND DICH EN 0 a ee User Manua Product description Wireless FPV monitor with dual receiver LCD monitor is a new multi function product adopts advanced integrated circuits and high quality new HD LCD monitor It integrates a high sensitivity 32channel and dual 5 8GHZ AV wireless receivers It is with Aerial receiver high definition monitor easy to operate which can be used for FPV ground station security monitoring baby monitors photography viewfinder construction site video surveillance advertising and other venues AN To insure best use of the unit please read the user s manual carefully CAUTION 1 Do not use any damaged or leaking battery and please replace the battery immediately if it s working life becomes short significantly 2 Do not expose this product to direct sunlight heat or humid conditions 3 Keep away from strong light while using this product so as to obtain the clearest and the most colorful picture Please use sun shade for the outdoor necessary 4 Please avoid heavy impact or drop on the ground 5 Do not use chemical solutions to clean this unit Please simply wipe with a clean soft cloth to keep the brightness of the surface 6 Without adjustable component in the unit please do not take apart or repair the unit by yourself to avoid damage the product Product Feature eDual antenna recei
4. crease the adjustment of value button 3 2 OSD Operation Instruction in PC VGA State W color Brightness a 6 S C50 Contrast a 6S C50 Saturation E 5 Color Temp 6500K 1920x1080 60HZ X Brightness To adjust the Image brightness X Contrast To adjust the brightest and darkest ratio of the image please note the sense of picture when adjust proportion too large or small will make the picture lose the color of showy X Saturation To adjust color saturation X Color Temp OSD IN PC mode the image s Color Temp could be chosen and adjusted When select User It could be chosen R G B to adjust the corresponding analog value to meet the different user s requirement on the color of the image adjust Auto Config H Position V Position Phase Clock 1920x1080 60HZ XAuto Config To adjust automatically If the auto adjust does not satisfy your request you can adjust manually XH Position To adjust the picture in horizontal XV Position To adjust the picture in vertical XPhase To adjust the phase XClock To adjust the clock make field and line synchronization Blosn Language English H Position ZS C50 V Position ZS C50 OSD Timeout Off Transparent Off 1920x1080 60HZ X Language To choose OSD language check below English fk X Francais Italiano Deutsch Espanol H zg ZAO Pycc Portugues 11 X H Position To adjust the OSD position in horizontal X V Position
5. ctions 3 1 Button instructions O gt ON OFF Key S MODE gt gt Input signal switch button in OSD for exit button gt Menu key under a signal input mode pressing this button to pop up the menu and the current menu and sub menu item to confirm the adjustment gt CH Q gt Multi button In different input state it has different functions In RF state Auto Searching Long press this button for 23 seconds to enter the channel scan Manual adjustment directly press this button to set 1 8CH In VIDEO HDMI DVI VGA state No menu is displayed press this button to increase the volume In OSD Enter the menu operation press button to confirm and enter sub menu then press this button to select or set adjustment items Enter the adjustment items it is used to set and increase the adjustment of value button lt BAND gt Multi button In different input state it has different functions In RF State Manual adjustment to set BAND A B E F Volume adjustment in RF state need to press this button to confirm When screen appears the volume adjustment press this button to decrease the volume press2 CH button to increase the volume In VIDEO HDMI DVI VGA state No menu is displayed directly press this button to decrease the volume In OSD Enter the menu operation press button to confirm and enter sub menu then press this button to select or set adjustment items Enter the adjustment items it is used to set And de
6. em is consistent with the input video color system can choose other system to check 5 4 No Sound 1 Volume control did not open press the volume button gt CH Q try increasing the volume 2 Check if the audio input is normal or not In RF receiving please check if the transmitting terminal has a Audio signal emission 5 5 Open the RF no signal detected Transmitter is working properly or not 2 If transmitter frequency matches with the receiver frequency band 3 If customer change the receiving antenna please note that must be matched with the transmitter otherwise may cause receiving sensitivity is low even can t receive signals 4 Channel research or Manually set the channel m Remark If there are still any problems you can connect with the related deals As we constantly strive to improve product features and product performance if there is any change to Operation Manuel without prior notice
7. in vertical X OSD Timeout To adjust the clock x Transparent To adjust the level of transparent dF unction Reset System X Reset Back to original setting X System In VIDEO State to choose the color video Formats In HDMI DVI State the function is useless e XVolume To adjust the volume 4 Parameters Panel Size Panel Type Resolution 4 3 Display Raio fo Ea 480i 480p 576i 576p 720p 1080i 1080p 50 60Hz Headphone output Input Voltage DC 6 24V 5 8 G broadband FM audio and video synchronization RF receiving receiving other frequencies optional frequency Storage Temperature 30 65 C 16 32 channel auto searching Automatic channel search 5 Trouble shooting 5 1 Only black and white image 1 Make the level of color Saturation Brightness and Contrast is proper 2 Enter the menu item Function check whether the color system is consistent with the input video color system can choose other system to check 5 2 Power on but no picture 1 Make sure the signal output connect to the signal input of the monitor are in good condition press MODE button to check If in RF channel Please check to see if the transmitter has been working 2 Make sure you are using the standard power adapter to connect the monitor 5 3 Images are not synchronized RF Signal is too weak 2 Enter the menu item Function check whether the color syst
8. ue button 3 4 lt BAND Multi button in VIDEO HDMI DVI VGA input state volume down button In RF state Press gt CH Q button to enter the manual channel to set BAND A B E F transformation In OSD to select or set adjustment items and the decrease adjustment of value button 5 E Menu Button 6 gt MODE nput signal selection or exit the menu 1 2 Rear View 1 7 Power input jack When clients use their own power supply please make sure that the supply current shall not be less than 1 2 A and 4 voltage range in 6 24 v qualified dc power supply 2 HDMI IN HD HDMI signal input jack 3 DVI IN Digital video signal input jack 4 VGA IN VGA signal input jack 5 4 Stereo headphone output jack 6 Black DC jack DC input 7 Red RCA jack Analog audio signal input 8 Yellow RCA Jack VIDEO signal input 2 Wireless transmits receiver operation Take the form a complete set of the antenna assemble on the unit s antenna input ports the assembly should be secured locked on the buckle 2 1 Frequency band selection Wireless transmitter channel and receiver channel must be strictly consistent otherwise it will not receive a transmitter signal This unit can auto searching for 32 receiver channels also can accept simultaneously multi transmitters and receivers together work to avoid co channel interference Wireless 3 8GHz Diversity Recelver BAND CH1 CH2 CH3
9. ver high sensitivity strong anti interference e5 8G wireless receiver a monitor for the integration of multi functional combination machine compact suitable for a variety of purposes e 90dbm high sensitivity 5 8G wireless receiver 32 Channel Auto scan effectively avoid signal interference eChannel auto scan and channel choice of menu buttons function improve the accuracy and convenience of channel choice eAerial video receives no blue screen eHigh brightness Contrast Anti glare screen with a sun shade Sun clearly visible eWith VIDEO AUDIO HDMI DVI VGA input suitable for a Variety of sources eColor Control Systems support enter the menu to manually select the appropriate format and adaptable eHeadphone monitors playback audio effects CONTENTS 1 Product description 3 2 Wireless transmits receiver operation 5 3 Operation instructions 8 4 Parameters 16 5 Trouble shooting 17 1 Product description 1 1 Front view 76543 2 1 Power Indicator 2 ON OFF Key 3 2 CH Q Multi button in VIDEO HDMI DVI VGA input state Volume up button ln RF state long press this button for about 3 seconds to enter the channel auto scan Press this button for Manual channel setting to set channel 1 8CH ln OSD to select or set adjustment items and the increase adjustment of val
Download Pdf Manuals
Related Search