Hobby King Apache OSD User Manual
Contents
1. Hobby King Apache OSD User Manual Yellow Red Black Audio Video Link Red Black Voltage Auxiliary Red Blue GPS Serial Blue Red Black Serial Auxiliary Red Blue Infrared Sensor Orange Red Brown PPM Signal 1 1 Hardware Connection Red Green Yellow Accessory Orange Red Brown PPM Signal 2 Red Green Yellow Accessory Red Green Yellow Accessory Black Red Green Yellow Accessory Red E Co Pilot i White Red White Yellow Power Module Yellow Figure 1 1 OSD Main Board Ports Figure 1 2 Port Group A Figure 1 11 Port Group B A Port Group A 1 1 Audio Video Port Its for connecting the camera 1 2 GPS USB Module Port Its for connecting GPS module or USB data module but they cannot connect the main board meantime to Figure 1 5 USB Data Module 1 4 Other Sensor Module Ports We supply four couples of ports for connecting the other OSD modules they have the same function Any port can connect to our other supplied modules OSD main board can automatically detect the module type Figure 1 6 IR Receiver Module Figure 1 7 IR Remote Controller 1 5 OSD Power Module Port Its a must part for AEO OSD it must be connected to supply power to all the OSD parts and meantime it can sensor the real current Amps and Volt of the power battery B Port Group B 1 6 Aux Voltage Detection Port There re two modes for this port When it s set auxiliary voltage detection mode pls us2. d land the plane when The power battery is low The video battery is low The video link is not stable The RSSI reading is low The HDOP reading is close to 3 The GPS signal quality indication is low And the plane must be landed as soon as possible when The video link is not stable The RSSI warning is indicated Any GPS failure is indicated The HDOP reading is suddenly increased for more than 3 After Landing After landing you may press the red reset button on the infrared remote controller while the OSD system is in the in flight interface screen to reset the Relative Altitude Maximum Altitude Reached Distance to Home Home Direction and also the Timer if it is set to the Take Off Start mode back to zero In the same time the home position recorded in the system will be replaced by the current location coordinate Thanks for using our products Entire Contents Copyright 2011 2 V1 03
3. e the cables in Figure 1 12 to connect and measure the power For example video transmitter and camera usually use the male JST to supply power When it s set RSSI mode connect receiver RSSI output to this port pls no tice the red is positive and black is negative Figure 1 10 Power Module Other Ports TF Card Slot Slot the TF can record the flight data The TF card supports max 8GB The card has to be pre formatted with FAT32 before using 2 OSD In flight Interface Screen amp Setting Menu Figure 1 12 Aux Volt Detetion Cable Entire Contents Copyright 2011 1 V1 03 2 1 4 Temperature 2 3 3 Main Sea Level Altitude 2 4 2 Direction Heading s A 3 1 1 Unit Setting 3 4 1 Flight Recorder 2 1 1 Timer 000 00 ee 2 4 7 Max Alti Reached Metric On Off Switch 1 3 1 2 GPS Time 2 1 2 Date 2 4 8 Distance to Home 2 1 3 Time en 3 2 1 Power Battery Fuel Gauge Setting 2 4 9 Speed Scale 3 1 3 Home Distance Z Z lt 5 Cone Rae Mode Setting 3 2 2 Power Battery 3 3 2 Aux Port Sensor Calibration 2 4 4 Relative Altitude A 2 6 1 Horizontal Datum 3 3 Aux Volt 2 2 2 Power Battery 3 2 2 Power Battery Gauge Voltage Port Settings 2 4 5 Altitude Scale 3PS 1 2 Y ai 2 2 4 Power Battery kem aE 30 6472 3 2 2 Power Battery EA anaa emery 3 4 2 OSD Consume d Energy ees TF Card Ready 2 3 1 GPS Status Current POWER 12 3 Display Setting POWER 00 3A 2 2 1 Power Battery Volt 2 2 3 Power Batter
4. y Current 2 6 2 Flight Recorder Status 2 3 2 Position Coordinate Figure 2 1 On Screen Display Contents Figure 3 1 OSD Configuration Menu 3 How to Use Before Powering Up the System All connection must be made before powering up the system Ensure the GPS antenna is facing up and not blocked from the sky Make sure all components are securely fixed in the plane The GPS must be kept away from all electronic components especially the electrical speed controller video transmitter and wireless mo dem transceiver Before Taking Off Connect battery for the on board video system if there is any turn on the ground video receiver and display system Turn the RC transmitter on make sure the throttle stick is pulled at the low position and then connect the power battery to power up the OSD system If there is any separated battery pack for RC receiver power the RC receiver up before the power battery is connected Place the plane at the taking off position and keep it to be stationary until the position is locked by the GPS and the HDOP reading is not more than 3 It may take some time for the position to be locked and the HDOP reading is dropped to 3 in the poor weather con dition It is not recommended to take off if the HDOP reading is more than 3 After Taking Off You may take off the plane after a standard range check for the radio system and the plane condition before the flight Do please prepare to return to the take off position an
Download Pdf Manuals
Related Search