ASSEMBLY INSTRUCTIONS
Contents
1. ASSEMBLY INSTRUCTIONS ATTENTION THIS PRODUCT IS NOT FOR COMMERCIAL USE INTENDED FOR RESIDENTIAL USE ONLY RUS422W wm A Do not discard any of the packaging until you have checked that you have all the parts and pack of fittings R TT children away during assembly This item contains small parts which can be swallowed by children Children should always be under direct adult supervision while using the product a Retain the assembly instructions for future reference A Please quote following FQC NO when contacting service center E E SERVICE CENTER TOLL FREE NO TEL 1 877 539 7436 FAX 1 877 539 7439 DON T RETURN TO STORE PAGE 1 OF 6 COURTYARD CREATIONS INC A Please read instructions thoroughly Acquaint yourself with the inventory of parts and the accompanying drawings to ensure safe and proper assembly B You will need the following tools Phillios Screwdriver Not Included Nut Wrench See Part 29 Hex Key Wrench See Part 28 C Lay out all parts on a flat surface and identify them using the table below 6 17C01A0822071Y4 pe BOLT M8 75 17C01A0725101Y4 6 YY BOLT M6 75 17C01A0716072Y4 BOLT M6 45 PARTS eo MATERIAL CODE PART OOTY RUS422W CS02 F TOP CROSS BEAM W ADJUSTABLE TEETH Ss j ooh DM 2 Noy 18 9 17017A1306001Y4 WASHER d6 5 D16 1 2 WASHER d8 5 D17 1 6 1800023001 PLASTIC NUT M6 P1 0 PLASTIC NUT M 62RUS422WN102. 2 REAR UPRIGHT SUPPORT 43 62RUS422WN101 FRONT UPRIGHT SUPPORT SCREW ST4 2 16 fo 62RUS422W1101 LATERAL CROSS BRACE m 62RUS459FH102 O1 A EE Ehra REAR GROSS BRAGE He RUS4060 CS02N SWING ARM SEAT ASSEMBLY 62RUS422WM101 SWING ARM TUBE SIDE CANOPY BRACE FRONT REAR CANOPY BRACE FRONT LEG CAP 12 2800221024 REAR LEG CAP SUSPENSION SPRING 14 17C01A0714003Y4 6 om 5 OP i Bas BOLT CAP M6 BOLT CAP M8 CANOPY FRAME CONNECTOR PLASTIC _ HEX KEY a 6MM arwa aes D a CG NUT WRENCH 138 amp 17MM CANOPY 31 61R422WCO00001BA Ls pracawconorey LJ BOLT M6 40 17C01A0722011Y4 Om 4 BOLT M6 65 stor DON T RETURN TO STORE PAGE 2 OF 6 ASSEMBLY Note For all nuts and bolts fastening always use a washer 20 or 21 between the tube and bolt or the tube and nut Step A 1 and Step A 2 Insert the top cross beam w adjustable teeth 1 into the upright supports 2 and 3 Fasten them by using bolts 14 washers 20 and plastic nuts 22 Repeat the procedure for the other side Do not tighten bolts amp plastic nuts yet Step A 3 Fasten the lateral cross braces 4 to the upright supports 2 and 3 by using bolts 15 washers 20 and plastic nuts 22 Repeat the procedure for the other side Do not tighten bolts amp plastic nuts yet Step A 4 Fasten the rear cross brace 5 to the rear upright supports 2 by using bol
3. D IN SHIPMENT The store where you made your purchase amp SHOULD YOU EXPERIENCE ANY DIFFICULTY DURING ASSEMBLY OR IF ANY Eo elo ea eu Sl PART IS MISSING OR DAMAGED PLEASE CALL THE HELP LINE 1 877 539 7436 arenes sete freee BEFORE RETURNING THE ITEM TO THE STORE Call Toll Free PLEASE PROVIDE THE FOLLOWING INFORMATION Ural eee 1 MODEL NUMBER OF THE PRODUCT Call us between 9 00 AM and 4 30 PM 2 PART NUMBER AND MATERIAL CODE OF THE PART FROM THE PARTS LIST AN ASSN ANUS Easy SHOWN ON ASSEMBLY INSTRUCTIONS MOST PROBLEMS CAN BE RESOLVED WITHOUT RETURNING THIS PRODUCT TO THE RETAILER DON T RETURN TO STORE PAGE 6 OF 6
4. e Do not use bleach acid or other solvents on the fabric or frame parts e In order to prolong the life and beauty of your swing we recommend that the swing be stored in a dry area when not in use For example overnight or on rainy days e Please inspect and tighten all bolts or fasteners on a regular basis to ensure proper performance and safety of your swing Special Warnings The user of this swing should always inspect it before each use 1 It is essential to place the swing on level ground and not less than 6 feet from any obstruction such as fences garages the house overhanging branches laundry lines or electrical wires Check all bolts and nuts for tightness on a regular basis Make sure the suspension springs are always properly hooked before each use Oil all metallic moving parts during usage season Always remove the canopy in heavy wind conditions otherwise the canopy may tip over and may cause damage to its parts The manufacturer will not accept responsibly for unauthorized repair or modifications to the swing 7 Weight limit 750 Ibs O AOUN O PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY STOP amp PLEASE SEPARATE AND IDENTIFY ALL PARTS MAKING SURE THAT YOU i z HAVE ALL OF THE PARTS LISTED Missing A Part X SHOULD YOU NOT LOCATE ALL OF THE ABOVE PARTS PLEASE INSPECT ALL No Need To Go Back To PACKING MATERIAL FOR ANY SMALL PARTS THAT MAY HAVE BECOME The Store SEPARATE
5. ross beam w adjustable teeth 1 and the swing arm tubes 8 stop DON T RETURN TO STORE PAGE 4 OF 6 Step E 1 amp StepE 2 Slide the canopy frame connectors 26 into the side canopy braces 9 Fasten them together by using screws 19 in the pre drilled holes Ensure that the teeth on the canopy frame connectors are facing toward the inside of the frame Step E 3 Insert the front rear canopy braces 10 into the sleeves of the canopy 30 on both sides Step E 4 Insert the tube ends of the front and rear canopy braces 10 into the side canopy braces 9 Step E 5 Velcro the canopy 30 to the side canopy braces 9 Step F Fasten the canopy frame connectors 26 to the adjustable teeth on the top cross beam w adjustable teeth 1 by using a plastic screw 27 Do this procedure for both sides DON T RETURN TO STORE PAGE 5 OF 6 Step G Place the cushions 31 onto the seat assembly 7 Secure the cushions to the seat assembly by using ties To assure stability double check that all of the bolts have been completely tightened and then cover them with bolt caps 24 and 25 Warning To avoid danger of suffocation please keep plastic bags or small parts away from babies and children Cleaning and Maintenance e Wash frame parts and fabric with mild soap and water rinse thoroughly Dry frame completely and allow the fabric to drip dry
6. ts 14 washers 20 and plastic nuts 22 Tighten all of the bolts amp plastic nuts now Step A 5 Insert the leg caps 11 and 12 to the rear and front base feet Note The labels marked A and B on the legs caps 11 and 12 should Step A 5 to ensure proper assembly Fig A Do not tighten bolts nuts after Step 1 Fasten all bolts nuts after Fig A stop DON T RETURN TO STORE PAGE 3 OF 6 Step B Open the seat assembly 7 and fasten a swing arm tube 8 and a swing arm 6 to the seat back by using bolt 17 washers 20 and plastic nut 22 Do the same procedure for both sides Fasten another swing arm tube 8 to the swing arm 6 at the front bend by using bolt 18 washers 20 and plastic nut 22 Do the same procedure for both sides Fasten the other end of the swing arm 6 to the front of the seat assembly 7 by using bolt 16 washers 21 and plastic nut 23 Do the same procedure for both sides See Fig B Step C Hook the suspension springs 13 into the top of both swing arm tubes 8 Do the same procedure for both sides Step D Hang the opposite ends of the suspension springs 13 into the holes located on the angled braces of the top cross beam w adjustable teeth 1 Do the same procedure for both sides Warning Make sure that both ends of the suspension springs 13 go completely through the holes on the top c
Download Pdf Manuals
Related Search