Home

Lenovo S205S User's Manual

1. Ifthe problem continues go to Lenovo IdeaPad S205s on page 27 Note Noise from the AC adapter does not always indicate a defect Checking operational charging To check whether the battery charges properly during operation use a discharged battery pack or a battery pack that has less than 50 of the total power remaining when installed in the computer 21 d IdeaPad S205s Hardware Maintenance Manual 22 Perform operational charging If the battery status indicator or icon does not light on remove the battery pack and let it return to room temperature Reinstall the battery pack If the charge indicator or icon is still off replace the battery pack If the charge indicator still does not light on replace the system board Then reinstall the battery pack If it is still not charged go to the next section Checking the battery pack Battery charging does not start until the Power Meter shows that less than 9596 of the total power remains under this condition the battery pack can charge to 1009 of its capacity This protects the battery pack from being overcharged or from having a shortened life To check your battery move your cursor to the Power Meter icon in the icon tray of the Windows taskbar and wait for a moment but do not click it and the percentage of battery power remaining is displayed To get detailed information about the battery double click the Power Meter icon Note If the battery pack becomes
2. Safety information This chapter presents the following safety information that you need to get familiar with before you service an IdeaPad S205s computer General safety on page 2 Electrical safety on page 3 e Safety inspection guide on page 5 e Handling devices that are sensitive to electrostatic discharge on page 6 Grounding requirements on page 6 e Safety notices multilingual translations on page 7 Laser compliance statement on page 14 d IdeaPad S205s Hardware Maintenance Manual General safety safety Follow these rules below to ensure general safety Observe a good housekeeping in the area where the machines are put during and after the maintenance When lifting any heavy object 1 Make sure that you can stand safely without slipping 2 Distribute the weight of the object equally between your feet 3 Use a slow lifting force Never move suddenly or twist when you attempt to lift it 4 Lift it by standing or pushing up with your leg muscles this action could avoid the strain from the muscles in your back Do not attempt to lift any object that weighs more than 16 kg 35 Ib or that you think is too heavy for you Do not perform any action that causes hazards to the customer or that makes the machine unsafe Before you start the machine make sure that other service representatives and the customer are not in a hazardous position Place removed covers and other p
3. Safety information Safety notice 8 A DANGER Before removing any FRU turn off the computer unplug all power cords from electrical outlets remove the battery pack and then disconnect any interconnecting cables Avant de retirer une unit remplacable en client le mettez le syst me hors tension d branchez tous les cordons d alimentation des socles de prise de courant retirez la batterie et d connectez tous les cordons d interface Die Stromzufuhr muB abgeschaltet alle Stromkabel aus der Steckdose gezogen der Akku entfernt und alle Verbindungskabel abgenommen sein bevor eine FRU entfernt wird AUtian NN maa v 1n v55 FRU pro 0995 103115 bon YUN INVAN 9923 55 NN PMII DANN n 9949 05035 180 n55105 TANI DN OND v ON Prima di rimuovere qualsiasi FRU spegnere il sistema scollegare dalle prese elettriche tutti 1 cavi di alimentazione rimuovere la batteria e poi scollegare 1 cavi di interconnessione FRU SPD ARINC ThinkPad OER E Uo C 3 CORRA FALE V bBAULCCESUN KIL RYT I RVD EAL BERRIN ZLTE Antes de quitar una FRU apague el sistema desenchufe todos los cables de las tomas de corriente el ctrica quite la bater a y a continuaci n desconecte cualquier cable de conexi n entre dispositivos 13 d IdeaPad S205s Hardware Maintenance Manual Laser compliance statement compliance statement Some models of Lenovo IdeaPad computer are equipped from the factory with an optical storage device such a
4. When using testers set the controls correctly and use the approved probe leads and accessories for that tester Stand on suitable rubber mats obtained locally if necessary to insulate you from grounds such as metal floor strips and machine frames Observe the special safety precautions when you work with very high voltages instructions for these precautions are in the safety sections of maintenance information Be extremely careful when you measure the high voltages Regularly inspect and maintain your electrical hand tools for safe operational condition Do not use worn or broken tools and testers Never assume that power has been disconnected from a circuit First check it to make sure that it has been powered off d IdeaPad S205s Hardware Maintenance Manual Always look carefully for possible hazards in your work area Examples of these hazards are moist floors nongrounded power extension cables power surges and missing safety grounds Do not touch live electrical circuits with the reflective surface of a plastic dental mirror The surface is conductive such touching can cause personal injury and machine damage Do not service the following parts with the power on when they are removed from their normal operating places in a machine Power supply units Pumps Blowers and fans Motor generators and similar units This practice ensures correct grounding of the units e f an electrical accident
5. e Some computers have both a processor board and a system board If you are instructed to replace either of them and replacing one of them does not solve the problem reinstall that board and then replace the other one e If an adapter or a device consists of more than one FRU any of the FRUs may be the cause of the error Before replacing the adapter or device remove the FRUs one by one to see if the symptoms change Replace only the FRU that changed the symptoms Attention The setup configuration on the computer you are servicing may have been customized Running Automatic Configuration may alter the settings Note the current configuration settings using the View Configuration option then when service has been completed verify that those settings remain in effect Strategy for replacing a hard disk drive Always try to run a low level format before replacing a hard disk drive This will cause all customer data on the hard disk to be lost Make sure that the customer has a current backup of the data before performing this action Attention The drive startup sequence in the computer you are servicing may have been changed Be extremely careful during write operations such as copying saving or formatting If you select an incorrect drive data or programs can be overwritten Important notice for replacing a system board Some components mounted on a system board are very sensitive Improper handling can cause damage to those
6. 1090 DIMM 47 1100 Fan assembly and heat sink assembly 48 1110 System board E 50 1120 e 53 1130 Bluetooth card gegen 54 1140 LCD front bezel 55 1150 LCD panel LCD cable and hinges 56 1160 Integrated camera 58 1170 Antenna assembly and LCD cover 59 LOcatiONS E 60 Front WOW c REY 60 Right side view 61 Bottom and Left side view 61 o NRI RR RR RR 62 Overall Y A 63 LCD Eege 65 i i DOE eec M 67 Miscellaneous parts 69 E A 70 OWED COTOS cues 71 NG CES ainia 74 Trademarks scans 15 lii About this manual IV This manual contains service and reference information for the following Lenovo IdeaPad product Lenovo IdeaPad S205s Use this manual to troubleshoot problems The manual is divided into the following sections The common sections provide general information guidelines and safety information required for servicing computers The product specific section includes service reference and product specific parts information Important This manual is intended only for trained servicers who are familiar with Lenovo IdeaPad products Use this manual to troubleshoot problems effectively Before servicing a Lenovo IdeaPad product make sure to read all the information under Safety information on page and Important service information on page 16 Safety information
7. Italy e Longwell LP 22 HO3VV F LS 18 1m Korea e Longwell LP 486 KTLHO3VV F LS 5 1m P N 145000524 145000535 145000534 145000533 145000532 145000531 145000530 145000528 145000527 145000526 145000525 145000568 145000567 145000566 145000565 145000564 145000563 145000562 145000561 145000560 145000559 145000558 Table 9 Parts list 3 pin power cords continued Region Australia Longwell LP 23A LFC 3R LS 18 1m Taiwan Longwell LP 71 VCTF LS 33 1m Japan Longwell LP 54 VCTF LS 18 1m Africa e Longwell LP 39 H03VV F LS 18 1m CE e Longwell LP 34A HO3VV F LS 18 1m Lenovo IdeaPad S205s P N 145000557 145000556 145000555 145000554 145000553 13 d IdeaPad S205s Hardware Maintenance Manual 0000000000000000000000000000000000000000 60000000000000000000000000000000000000000 74 00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Lenovo may not offer the products services or features discussed in this document in all countries Consult your local Lenovo representative for information on the products and services
8. quel No las desmonte ni recargue ni las eche al fuego o al agua ni las cortocircuite Des chelas tal como dispone la normativa local Utilice s lo bater as que se encuentren en la lista de piezas al sustituir la bater a La utilizaci n de una bater a no apropiada puede provocar la ignici n o explosi n de la misma d IdeaPad S205s Hardware Maintenance Manual 10 Safety notice 4 A DANGER The lithium battery can cause a fire an explosion or a severe burn Do not recharge it remove its polarized connector disassemble it heat it above 100 C 212 F incinerate it or expose its cell contents to water Dispose of the battery as required by local ordinances or regulations Use only the battery in the appropriate parts listing Use of an incorrect battery can result in ignition or explosion of the battery La pile de sauvegarde contient du lithium Elle pr sente des risques d incendie d explosion ou de br lures graves Ne la rechargez pas ne retirez pas son connecteur polaris et ne la d montez pas Ne l exposez pas une temperature sup rieure 100 C ne la faites pas br ler et n en exposez pas le contenu l eau Mettez la pile au rebut conform ment la r glementation en vigueur Une pile inappropri e risque de prendre feu ou d exploser Die Systembatterie ist eine Lithiumbatterie Sie kann sich entz nden explodieren oder schwere Verbrennungen hervorrufen Batterien dieses Typs d rfen nicht aufgeladen
9. zerlegt ber 100 C erhitzt oder verbrannt werden Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden Bei der Entsorgung die rtlichen Bestimmungen f r Sonderm ll beachten Beim Ersetzen der Batterie nur Batterien des Typs verwenden der in der Ersatzteilliste aufgef hrt ist Der Einsatz falscher Batterien kann zu Entz ndung oder Explosion f hren IN mssnonn n9 5v5 135 nby mynn NIDO SANNA DN PIO WINN ANN YWSWOS PN NNW N99 11055205 ANN ONT IN ANN 2595 n5v 30172n PNI 155101 NN 41305 PN GN MIYA 100 Du nyn w n55Yon NN p5 v5 v 09199 xnn DIN NN UNS MINA 7 wnnwn v O gt MIDNA DIN mans n55103 UMP V D DP DPIN mua 03 913n yssnonn IN n2 gt gt W MIDI 01999 5159 NINN La batteria di supporto e una batteria al litio e puo incendiarsi esplodere o procurare gravi ustioni Evitare di ricaricarla smontarne il connettore polarizzato smontarla riscaldarla ad una temperatura superiore ai 100 gradi centigradi incendiarla o gettarla in acqua Smaltirla secondo la normativa in vigore DPR 915 82 successive disposizioni e disposizioni locali L impiego di una batteria non adatta potrebbe determinare l incendio o l esplosione della batteria stessa FDA RY FV ih KK HR SHEET PERAZA KEE EE RYT V ORB E EE Z DNA L Ay TJ ABOG 100 C 212 PL E O RR PR EMO PERICO EURO ES VN SYT YERERE SRAM BARRO FRANCES TS HSV MBR Y EM E Lekt TV EN SALTS RSV Roc ed
10. 44 1080 Hard disk drive HDD on page 46 e 1090 DIMM on page 47 1100 Fan assembly and heat sink assembly on page 48 e 1110 System board on page 50 Figure 12 Removal steps of speakers Remove two screws Ml and release the cables from the cable guides B Step Screw quantity Color Torque B M2 x 3 mm flat head nylok coated 2 Black 1 6 kgfcm Remove the speakers in the direction shown by arrows El 53 d IdeaPad S205s Hardware Maintenance Manual 1130 Bluetooth card For access remove these FRUs in order e 1010 Battery pack on page 34 1020 Dummy card on page 35 e 1040 Keyboard on page 37 1050 Base cover on page 39 e 1060 PCI Express Mini Card for wireless LAN on page 42 e 1070 LCD unit on page 44 1080 Hard disk drive HDD on page 46 e 1090 DIMM on page 47 e 1100 Fan assembly and heat sink assembly on page 48 e 1110 System board on page 50 Figure 13 Removal steps of bluetooth card Remove the bluetooth card in the direction shown by arrow Mil 54 Lenovo IdeaPad S205s 1140 LCD front bezel For access remove these FRUs in order e 1010 Battery pack on page 34 e 1020 Dummy card on page 35 e 1040 Keyboard on page 37 1050 Base cover on page 39 e 1060 PCI Express Mini Card for wireless LAN on page 42 e 1070 LCD unit on page 44 Figure 14 Removal steps of LCD front bez
11. WAN TON ON JWI 002 PD DNDN 0 YN NN 190Y OD TD IN D Yy OY DYIIN DYNADN ON PME nw POD 29 mn9 mp1 15 AVVN ANNI DIM DIN DY Mann Nel caso che caso l LCD si dovesse rompere ed il liquido in esso contenuto entrasse in contatto con gli occhi o le mani lavare immediatamente le parti interessate con acqua corrente per almeno 15 minuti poi consultare un medico se 1 sintomi dovessero permanere LCD SIAL LCD OT O HICAoO7U Fiche O LESA dk ARARA TE BBS amp DIRS P b 15 i UL T 725v Dev LL REUS co Cf DOPOR RANEGA EMO ASEO C lt CC Vv Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos lave inmediatamente las reas afectadas con agua durante 15 minutos como minimo Obtenga atenci n medica si se presenta algun sintoma del fluido despues de lavarse 11 d IdeaPad S205s Hardware Maintenance Manual 12 Safety notice 6 N DANGER To avoid shock do not remove the plastic cover that protects the lower part of the inverter card Afin d viter tout risque de choc lectrique ne retirez pas le cache en plastique prot geant la partie inf rieure de la carte d alimentation Aus Sicherheitsgr nden die Kunststoffabdeckung die den unteren Teil der Spannungswandlerplatine umgibt nicht entfernen DUDIN DOI NN PONY PN mbnawnnn MIDD 15 Pann 090995 SY ymnnn IPIN Sy van Per evitare scosse elettriche non rimuovere la copertura in plastica che avvolge la parte inferiore della sche
12. a wireless LAN card that has three antenna connectors plug the black cable 1st MAIN into the jack labeled 1 the grey cable 3rd into jack labeled 3 and the white cable 2nd AUX into jack labeled 2 on the card 43 d IdeaPad S205s Hardware Maintenance Manual 1070 LCD unit remove these FRUs in order 1010 Battery pack 1020 Dummy card For access on page 34 on page 35 on page 37 5 C 1040 Keyboard C 1050 Base cover on page 39 1060 PCI Express Mini Card for wireless LAN on page 42 Di Figure 7 Removal steps of LCD unit Remove the LCD connector ll and release the LCD cable and antenna cables from the cable guides El Remove two screws E1 DI HD _ _ A 0 Torgue Color Black Screw guantity M2 x 5 mm flat head nylok coated 2 Step 1 6 kgfcm 44 Lenovo IdeaPad S205s Figure 7 Removal steps of LCD unit continued Swing the LCD hinges in the direction shown by arrows B Remove the LCD unit in the direction shown by arrow B 45 d IdeaPad S205s Hardware Maintenance Manual 1080 Hard disk drive HDD For access remove these FRUs in order e 1010 Battery pack on page 34 1020 Dummy card on page 35 1040 Keyboard on page 37 1050 Base cover on page 39 1060 PCI Express Mini Card for wireless LAN on page 42 e 1070 LCD unit on page 44 Attention Do not drop the hard disk dr
13. components and may cause a system malfunction Attention When handling a system board Do not drop the system board or apply any excessive force to it Avoid rough handling of any kind Avoid bending the system board and hard pushing to prevent cracking at each BGA Ball Grid Array chipset 17 d IdeaPad S205s Hardware Maintenance Manual Important information about replacing RoHS compliant FRUs 18 RoHS The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive 2002 95 EC is a European Union legal requirement affecting the global electronics industry RoHS requirements must be implemented on Lenovo products placed on the market after June 2006 Products on the market before June 2006 are not required to have RoHS compliant parts If the original FRU parts are non compliant replacement parts can also be non compliant In all cases if the original FRU parts are RoHS compliant the replacement part must also be RoHS compliant Note RoHS and non RoHS FRU part numbers with the same fit and function are identified with unique FRU part numbers Lenovo plans to transit to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo s requirements and schedule in the EU Products sold in 2005 and 2006 will contain some RoHS compliant FRUs The following statement pertains to these products and any product Lenovo produces containing RoHS compliant F
14. occurs Caution do not become a victim yourself Switch off the power Send the victim to get medical aid Safety information Safety inspection guide inspection guide The purpose of this inspection guide is to assist you in identifying potential unsafe conditions As each machine was designed and built reguired safety items were installed to protect users and service personnel from injury This guide addresses only those items You should use good judgment to identify potential safety hazards according to the attachment of non Lenovo IdeaPad features or options not covered by this inspection guide If any unsafe conditions are present you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem Consider these conditions and the safety hazards they present Electrical hazards especially primary power primary voltage on the frame can cause serious or fatal electrical shock Explosive hazards such as a damaged CRT face or a bulging capacitor Mechanical hazards such as loose or missing hardware To determine whether there are any potential unsafe conditions use the following checklist at the beginning of every service task Begin the checks with the power off and the power cord disconnected Checklist 1 Check exterior covers for damage loose broken or sharp edges 2 Turn off the computer Disconnect the power cord 3 Check the p
15. pack on page 34 e 1020 Dummy card on page 35 e 1040 Keyboard on page 37 e 1050 Base cover on page 39 e 1060 PCI Express Mini Card for wireless LAN on page 42 e 1070 LCD unit on page 44 Figure 10 Removal steps of fan assembly and heat sink assembly Note Loosen six screws lll but do not remove them Detach the fan connector in the direction shown by arrow Pl When installing Make sure that the fan connector is attached firmly to the system board 48 Lenovo IdeaPad S205s Figure 10 Removal steps of fan assembly and heat sink assembly continued Lift the fan assembly and heat sink assembly in the direction shown by arrows H Be careful not to damage the connector When installing Before you attach the fan assembly to the computer apply thermal grease at an amount of 0 2 grams to the EX E3 part shown in the figure above Either too much or too less grease application can cause a thermal problem due to imperfect contact with a component 49 d IdeaPad S205s Hardware Maintenance Manual 1110 System board Important notices for handling the system board When handling the system board bear the following in mind Be careful not to drop the system board on a bench top that has a hard surface such as metal wood or composite Avoid rough handling of any kind In the whole process make sure not to drop or stack the system board f you put a system board down make sur
16. 00000000000000000000000000000000000000000000000000000000000 This chapter presents the following important service information Strategy for replacing FRUs on page 16 Strategy for replacing a hard disk drive on page 17 Important notice for replacing a system board on page 17 Important information about replacing RoHS compliant FRUs on page 18 Important BIOS and device driver fixes are customer installable The BIOS and device drivers are posted on the customer support site http consumersupport lenovo com Strategy for replacing FRUS for replacing FRUs Before replacing parts Make sure that all software fixes drivers and BIOS downloads are installed before replacing any FRUS listed in this manual After a system board is replaced ensure that the latest BIOS is loaded to the system board before completing the service action To download software fixes drivers and BIOS follow the steps below 1 Go to http consumersupport lenovo com 2 Enter a serial number or select a product or use Lenovo smart downloading 3 Select the BIOS Driver Applications and download 4 Follow the directions on the screen and install the necessary software 16 Important service information Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs If you are instructed to replace an FRU but the replacement does not solve the problem reinstall the original FRU before you continue
17. 00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 This chapter presents the following product specific service references and product specific parts information Specifications on page 27 Status indicators on page 29 Fn key combinations on page 31 FRU replacement notices on page 32 Removing and replacing an FRU on page 33 Locations on page 60 Parts list on page 62 Specifications The following table lists the specifications of the Lenovo IdeaPad S205s Table 1 Specifications Feature Description Processor Core Chipset Bus architecture e Graphic memory chip Display Standard memory CMOS RAM Hard disk drive Optical drive Intel Calpella Platform 18W U5600 1 33G dual core HM55 1066 MHz FSB 800 MHz DDR3 SDRAM PC3 6400 PCI Bus PCI Express Bus DMI Intel HD Gfx 11 6 HD LED backlight Wedge type 1366 x 768 pixel WXGA 200 nit 255g DDR3 800MHz Support Dual Channel SODIMM socket x 1 2GB 512 bytes 2 5 9 5mm or 7mm SATA II 5400rpm External 12 7mm 2 5 USB RAMBO is Tray in type 27 d IdeaPad S205s Hardware Maintenance Manual 28 Table 1 Specifications continue
18. 10 SNE 1 Fn PriSc Fn Pause Fn Delete Fn 4 y Fn Description Turn on off the integrated camera Enter sleep mode Turn on off the LCD screen Open the interface for the display device switch to select notebook or external display Open the interface for integrated wireless devices settings enable disable Enable Disable the touchpad Start Pause playback of Windows Media Player Stop playback of Windows Media Player Skip to the previous track Skip to the next track Activate the F12 function You can press Fn F11 during computer startup to open the boot selection menu Activate the system request Activate the break function Enable Disable the Scroll Lock Increase Decrease display brightness Increase Decrease volume level 31 d IdeaPad S205s Hardware Maintenance Manual FRU replacement notices replacement notices This section presents notices related to removing and replacing parts Read this section carefully before replacing any FRU Screw notices Loose screws can cause a reliability problem In the Lenovo IdeaPad computer this problem is addressed with special nylon coated screws that have the following characteristics They maintain tight connections They do not easily come loose even with shock or vibration They are harder to tighten Each one should be used only once Do the following when you service this machine Keep the screw kit in your t
19. 205s Miscellaneous parts Table 7 Parts list Miscellaneous parts FRU P N System miscellaneous parts e a LU16 HDD BRACKET 31044111 e 6 LS205 LCD SCREW RUBBER 31049241 Cable miscellaneous parts 31044106 c LU16 BLUETOOTH CABLE Note Italicized letters in parentheses are references to the exploded view in Overall on page 63 and LCD FRUs on page 65 69 d IdeaPad S205s Hardware Maintenance Manual 70 AC adapters Table 8 Parts list 3 pin AC adapters FRU 40Wh Brazil PA 1400 12LB adapter 40Wh Delta ADP 40NH B adapter 40Wh Liteon PA 1400 12LC adapter 40Wh HIPRO LN A0403A3C adapter P N 36001715 36001648 36001653 36001672 Lenovo IdeaPad S205s Power cords A Lenovo IdeaPad power cord for a specific country or region is usually available only in that country or region Table 9 Parts list 3 pin power cords Region P N CCC 145000602 e SSD YD 118 1 IEC53RVV SSD 3 2B 1 1m CCC 145000600 e LINETEK PC323 RVV300 300 LS15 1m Argentina 145000599 LINETEK LS15 HO3VV F LP39 1m Danmark 145000598 e LINETEK LS15 HO3VV F LP 38 1m Switzerland 145000597 LINETEK LS15 HO3VV F LP 37 1m Brazil 145000596 LINETEK LS15 HO3VV F LP26A 1m Israel 145000595 LINETEK LS15 HO3VV F LP 41 1m UL 145000594 LINETEK LP 30B SPT 2 LS15 1m UK 145000593 e LINETEK LP 61L HO3VV F L S15 1m Indian 145000592 LINETEK PE 361 HO5VV F LS15 1m Italy 145000591 e LINETEK LS15 HO3VV F PE 336 1
20. 7mm 250G HDD 320G 5400rpm SATA Seagate ST320LT020 5400RPM 7MM 320G HDD 320G 5400rpm SATA HGST HTS545032A7E380 5400PRM7mm 320G Battery pack 2 2Ah 6Cell 48Wh S205 Sanyo L09S6Y 14 3S2P 48Wh Bty Battery pack 2 2Ah 6Cell 48Wh S205 SMP S LO9M6Y14 3S2P 48Wh Bty Battery pack 2 2Ah 6Cell 48Wh S205 Celx L LO9C6Y14 3S2P 48Wh Bty LU16 LOWER CASE BLACK AC adapter see AC adapters on page 70 FRU no 31044103 31044121 20002266 20002326 31047377 11014170 11012219 31044101 11012808 11012197 11200060 11013171 11200058 11012761 20002515 20002357 16005023 16005210 16004641 16200021 16200069 16005211 16200068 121001141 121001138 121001117 31044109 Lenovo IdeaPad S205s LCD FRUs In Lenovo IdeaPad S205s there are following types of LCDs e 11 6 in WXGA TFT 65 d IdeaPad S205s Hardware Maintenance Manual 66 11 6 in WXGA TFT Table 5 Parts list 11 6 in WXGA TFT No NO OP Go Go Ga M A FRU LS205s LCD Bezel TEX W Camera Hole LS205 HINGE CAP 11 6 Wedge B116XW02 VO HD HW3A 11 6 Wedge LP116WH1 TLN1 11 6 Wedge N116B6 L02 LU16 LCD HINGE PACK AMD L R LU16 CAMEAR 0 3M LS205s LCD Cable W Camera Cable LS205s LCD Cover W Antenna 4 For WWAN FRU no 31051972 31049238 18200130 18004193 18004189 31044113 31044155 31051971 31050787 Keyboard Table 6 Parts list Keyboard Language Sunrex Chicony English Bulgarian Int
21. IdeaPad S205s Hardware Maintenance Manual 1010 Battery pack A DANGER Only use the battery specified in the parts list for your computer Any other battery could ignite or explode Figure 1 Removal steps of battery pack Unlock the battery release lever ll Holding the battery release lever in the unlocked position Ell remove the battery pack in the direction shown by arrow El When installing Install the battery pack along the slide rails of the slot Then make sure that the battery release lever is in the locked position 34 Lenovo IdeaPad S205s 1020 Dummy card For access remove this FRU e 1010 Battery pack on page 34 Figure 2 Removal steps of dummy card Remove the dummy card in the direction shown by arrows ll El SE BS EE SF 35 d IdeaPad S205s Hardware Maintenance Manual 1030 SIM card For access remove this FRU e 1010 Battery pack on page 34 Figure 3 Removal steps of SIM card Push the SIM card in until you hear a click and then pull the SIM card out in the direction shown by arrow Bl 36 Lenovo IdeaPad S205s 1040 Keyboard For access remove this FRU 1010 Battery pack on page 34 Figure 4 Removal steps of keyboard Remove three screws Bl Step Screw quantity Color Torque E M2 x 2 mm flat head nylok coated 3 Black 1 6 kgfcm 37 d IdeaPad S205s Hardware Maintenance Manual Figure 4 Removal steps of keyboard continued L
22. Notes Each FRU is available for all types or models unless specific types or models are specified 62 Lenovo IdeaPad S205s Overall 63 d IdeaPad S205s Hardware Maintenance Manual 64 Table 4 Parts list Overall No ar Ga h A al 10 10 10 10 11 11 12 12 12 12 12 12 12 13 13 13 14 FRU LCD unit see LCD FRUs on page 65 Keyboard see Keyboard on page 67 LU16 TOUCH BUTTON BOARD AMD LU16 UPPER CASE AMD W TP8 SPEAKER BT2 1 amp BT3 0 Fcn BCM92070 BT2 1 EDR Flash U NB Bluetooth card BT2 1 amp BT3 0 USI BCM92070 BT2 1 EDR Flash U NB Bluetooth card LU16 XD DUMMY CARD INTEL 42 4J104 001 LS205s MB U5600 1 33G W THM 3G BT LU16 IO BOARD AMD W CABLE LU16 LED BOARD DDRIII 1333 2GB SAM M471B5773DH0 CH9 DDR3 1333 2GB DDRIII 1333 2GB HYN HMT325S6BFR8C H9 NO DDR3 1333 2GB DDRIII 1333 2GB RMT3010EC58E8F 1333 C 2Gb 40nm DDRIII 1333 2GB RMT3010KC58E8F 1333 Samsung C 2Gb 46nm DDRIII 1333 2GB SP321NHO8HAF C 2Gb 45nm DDRIII 1333 2GB NAN NT2GC64B88BONS CG DDR3 1333 2GB WLAN card Cbt RT3090 MOW M PCIE NB HMC WLAN card Liteon AR9285 HB95 BGN MOW NB HDD 250G 5400rpm SATA HGST HTS543225A7A384 5400RPM7MM 250G HDD 250G 5400rpm SATA Seagate ST250LT003 5400RPM 7MM 250G HDD 250G 5400rpm SATA Toshiba MK2565GSX 5400RPM 250G HDD 250G 5400rpm SATA WD WD2500BPVT 5400RPM 250G HDD 250G 5400rpm SATA HGST HTS545025A7E380 5400PRM
23. O 9000 as fully effective When handling ESD sensitive parts Keep the parts in protective packages until they are inserted into the product Avoid contact with other people Wear a grounded wrist strap against your skin to eliminate static on your body Prevent the part from touching your clothing Most clothing is insulative and retains a charge even when you are wearing a wrist strap Use the black side of a grounded work mat to provide a static free work surface The mat is especially useful when handling ESD sensitive devices Select a grounding system such as those listed below to provide protection that meets the specific service requirement Note The use of a grounding system to guard against ESD damage is desirable but not necessary Attach the ESD ground clip to any frame ground ground braid or green wire ground When working on a double insulated or battery operated system use an ESD common ground or reference point You can use coax or connector outside shells on these systems Use the round ground prong of the ac plug on ac operated computers Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function Proper grounding of the electrical outlet can be verified by a certified electrician Safety information Safety notices multilingual translations The safety notices in this section are provided in English F
24. RUs RoHS compliant FRUs have unique FRU part numbers Before or after the RoHS implementation date failed RoHS compliant parts must always be replaced with RoHS compliant ones so only the FRUs identified as compliant in the system HMM or direct substitutions for those FRUs may be used Products marketed before June 2006 Products marketed after June 2006 Current or Replacement FRU Current or Replacement FRU original part original part Non RoHS Can be Non RoHS Non RoHS Can be RoHS Must be RoHS Must be RoHS Non RoHS Can sub to RoHS RoHS Must be RoHS Note A direct substitution is a part with a different FRU part number that is automatically shipped by the distribution center at the time of the order General checkout General checkout This chapter presents the following information e What to do first on page 20 Power system checkout on page 21 Before you go to the checkout make sure to read the following important notes Important notes Only certified trained personnel can service the computer Before replacing any FRU read the entire page on removing and replacing FRUs When you replace FRUs use new nylon coated screws Be extremely careful during such write operations as copying saving or formatting Drives in the computer that you are servicing sequence might have been altered If you select an incorrect drive data or programs might be overwritten Replace an FRU only with another FRU of th
25. XX 7 Sau IS When installing Make sure that the metal connector is attached firmly 97 d IdeaPad S205s Hardware Maintenance Manual 1160 Integrated camera For access remove these FRUs in order e 1010 Battery pack on page 34 1020 Dummy card on page 35 e 1040 Keyboard on page 37 1050 Base cover on page 39 e 1060 PCI Express Mini Card for wireless LAN on page 42 e 1070 LCD unit on page 44 e 1140 LCD front bezel on page 55 e 1190 LCD panel LCD cable and hinges on page 56 Figure 16 Removal steps of integrated camera Note The integrated camera is stuck on the top center of the LCD cover Remove the integrated camera from the LCD cover in the direction shown by arrow ll When installing Stick the integrated camera to the top center of the LCD cover and ajust the placement of it to make sure the connector is attached firmly 58 Lenovo IdeaPad S205s 1170 Antenna assembly and LCD cover For access remove these FRUs in order e 1010 Battery pack on page 34 1020 Dummy card on page 35 e 1040 Keyboard on page 37 e 1050 Base cover on page 39 e 1060 PCI Express Mini Card for wireless LAN on page 42 e 1070 LCD unit on page 44 e 1140 LCD front bezel on page 55 e 1190 LCD panel LCD cable and hinges on page 56 Figure 17 Removal steps of antenna assembly and LCD cover Peel off the adhesive tapes securin
26. arts in a safe place keeping them away from all personnel while you are servicing the machine Keep your toolcase away from walk areas so that other people will not trip it over Do not wear loose clothing that can be trapped in the moving parts of the machine Make sure that your sleeves are fastened or rolled up above your elbows If your hair is long fasten it Insert the ends of your necktie or scarf inside clothing or fasten it with the nonconductive clip about 8 centimeters 3 inches from the end Do not wear jewelry chains metal frame eyeglasses or metal fasteners for your clothing Attention Metal objects are good electrical conductors Wear safety glasses when you are hammering drilling soldering cutting wire attaching springs using solvents or working in any other conditions that may be hazardous to your eyes After service reinstall all safety shields guards labels and ground wires Replace any safety device that is worn or defective Reinstall all covers correctly before returning the machine to the customer Fan louvers on the machine help to prevent the overheating of internal components Do not obstruct fan louvers or cover them with labels or stickers Safety information Electrical safety safety Observe the following rules when working on electrical eguipments Important Use only approved tools and test eguipments Some hand tools have handles covered with a soft material that d
27. currently available in your area Any reference to a Lenovo product program or service is not intended to state or imply that only that Lenovo product program or service may be used Any functionally equivalent product program or service that does not infringe any Lenovo intellectual property right may be used instead However it is the user s responsibility to evaluate and verify the operation of any other product program or service Lenovo may have patents or pending patent applications covering subject matter described in this document The furnishing of this document does not give you any license to these patents LENOVO GROUP LTD PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication Lenovo may make improvements and or changes in the product s and or the program s described in this publication at any time without notice The products described in this document are not intended for use in implantation or other life suppor
28. d Feature I O port MODEM slot Audio Video Ethernet on the system board PCI Express Mini Card slot Bluetooth wireless Keyboard Touch pad Integrated camera Battery AC adapter Pre installed operating system Description Stereo headphone jack Microphone jack VGA x 1 RJ45 x 1 on planar USB 2 0 port x 2 on planar eSATA USB combo port x 1 on planar HDMI x 1 5 in 1 card reader SD MMC MS MS pro xD N A 1 8 Stereo Headphone Output Jack 1 8 Input Jack Microphone Built in Stereo Speakers 2 x 1 5W with 6 cc chamber CRT port x 1 on planar 10 100 1000M Wireless LAN MiniCard PCle slot x 1 half size Wireless WAN MiniCard PCle slot x 1 full size select Models Built in antenna with min USB interface select Models 6 Row ISO Full Size Keyboard Two clicks and 1 LED indicator 0 3Million pixels 6 cell 2200mAh 20 V 40 W Win 7 Home Premium 32bit Lenovo IdeaPad S205s Status indicators indicators The system status indicators below show the computer status Table 2 Status indicators Indicator Meaning E Poweron White System is enabled b Blinking white System is in sleep mode Off System is in hibernate mode or shut down 29 d IdeaPad S205s Hardware Maintenance Manual Table 2 Status indicators continued Indicator Battery status 30 Wireless status UU Drive in use E Touchpad Meaning Blinking amber 500ms off 1s on The
29. da invertitore RREEE QIGO 4L4wA A X3 WOTWEDBRG UCCO SZZATyZ X vie SS TEV CS HEV Para evitar descargas no quite la cubierta de plastico que rodea la parte baja de la tarjeta invertida Safety notice 7 N DANGER Though the main batteries have low voltage a shorted or grounded battery can produce enough current to burn personnel or combustible materials Bien que le voltage des batteries principales soit peu lev le court circuit ou la mise la masse d une batterie peut produire suffisamment de courant pour br ler des mat riaux combustibles ou causer des br lures corporelles graves Obwohl Hauptbatterien eine niedrige Spannung haben k nnen sie doch bei Kurzschluf oder Erdung genug Strom abgeben um brennbare Materialien zu entz nden oder Verletzungen bei Personen hervorzurufen NIN T123 nn MIV IN n gt wN n m55Yonv qx DD 7991019 0 1 POAT n5129 MINI IN NINPA 9954 t 55210 HAYA IN MIMI Sebbene le batterie di alimentazione siano a basso voltaggio una batteria in corto circuito o a massa puo fornire corrente sufficiente da bruciare materiali combustibili o provocare ustioni ai tecnici di manutenzione FA ZAyTVU ORBIERAKS TH Va LURO HLc v7 VBR ROO PLEADED EROTICO DERE RE S ESBORD OES Aunque las baterias principales tienen un voltaje bajo una bateria cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal
30. e correct model When you replace an FRU make sure that the machine model and the FRU part number are correct by referring to the FRU parts list An FRU should not be replaced just because of a single unreproducible failure Single failures can occur for a variety of reasons that have nothing to do with a hardware defect such as cosmic radiation electrostatic discharge or software errors Consider replacing an FRU only when a problem recurs If you suspect that an FRU is defective clear the error logs and run the test again If the error does not recur do not replace the FRU Be careful not to replace a nondefective FRU 19 d IdeaPad S205s Hardware Maintenance Manual What to do E to do first When you do return an FRU you must include the following information in the parts exchange form or parts return form that you attach to it 1 Name and phone number of servicer Date of service Date on which the machine failed Date of purchase Procedure index and page number in which the failing FRU was detected Failing FRU name and part number Machine type model number and serial number Customer s name and address o S OG EN guo de Note for warranty During the warranty period the customer may be responsible for repair costs if the computer damage was caused by misuse accident modification unsuitable physical or operating environment or improper maintenance by the customer The following is a list of some common
31. e following information Restoring the factory contents by using OneKey Recovery on page 23 e Passwords on page 24 e Power management on page 25 Restoring the factory contents by using OneKey Recovery Restore of factory default The IdeaPad S205s computers come with pre installed OneKey Rescue System In order to save application files and the initial backed up files of the system the hard disk in a Lenovo computer includes a hidden partition when it is shipped If you need to restore the system to the point of your first boot up just enter Lenovo OneKey Rescue System and run Restore to factory default For details of OneKey Rescue System see the User Guide for OneKey Rescue System Note This will delete all the new data on the system partition C drive which is not recoverable Make sure to back up your critical data before you perform this action Using recovery discs When you replace a hard disk drive in your computer you are unable to use the pre installed Lenovo OneKey Recovery and OneKey Rescue However you can use the recovery discs that store your backed up data to restore your new hard drive to a previous backup status Note You can create recovery discs by burning the backup image to a CD DVD as recovery discs For details of Create recovery discs see the User Guide for OneKey Rescue System 23 d IdeaPad S205s Hardware Maintenance Manual When you use the recovery discs to boot yo
32. e order in which they are listed 4 Follow the correct sequence in the steps to remove the FRU as given in the figures by the numbers in square callouts 5 When turning a screw to replace an FRU turn it in the direction as given by the arrow in the figure 6 When removing the FRU move it in the direction as given by the arrow in the figure 7 To put the new FRU in place reverse the removal procedures and follow any of the notes that pertain to replacement For information about connecting and arranging internal cables see Locations on page 60 8 When replacing an FRU use the correct screw as shown in the procedures A DANGER Before removing any FRU turn off the computer unplug all power cords from electrical outlets remove the battery pack and then disconnect any of the interconnecting cables Attention After replacing an FRU do not turn on the computer until you have made sure that all screws springs and other small parts are in place and none are loose inside the computer Verify this by shaking the computer gently and listening for rattling sounds Metallic parts or metal flakes can cause electrical short circuits Attention The system board is sensitive to and can be damaged by electrostatic discharge Before touching it establish personal grounding by touching a ground point with one hand or using an electrostatic discharge ESD strap P N 6405959 to remove potential shock reasons 33 d
33. e to put it only on a padded surface such as an ESD mat or conductive corrugated material For access remove these FRUS in order e 1010 Battery pack on page 34 1020 Dummy card on page 35 e 1040 Keyboard on page 37 1050 Base cover on page 39 e 1060 PCI Express Mini Card for wireless LAN on page 42 e 1070 LCD unit on page 44 1080 Hard disk drive HDD on page 46 e 1090 DIMM on page 47 e 1100 Fan assembly and heat sink assembly on page 48 50 Lenovo IdeaPad S205s Figure 11 Removal steps of system board Detach two connectors in the direction shown by arrows M El Remove three screws Kl detach the speakers connector in the direction shown by arrow Ell and unplug the FPC connector in the direction shown by arrow El When installing Make sure that all the connectors are attached firmly Step Screw quantity Color Torque M2 x 5 mm flat head nylok coated 3 Black 1 6 kgfcm 51 d IdeaPad S205s Hardware Maintenance Manual Figure 11 Removal steps of system board continued Remove the system board in the direction shown by arrow KA 52 Lenovo IdeaPad S205s 1120 Speakers For access remove these FRUs in order e 1010 Battery pack on page 34 1020 Dummy card on page 35 e 1040 Keyboard on page 37 e 1050 Base cover on page 39 1060 PCI Express Mini Card for wireless LAN on page 42 e 1070 LCD unit on page
34. el Remove two screws Ml Step Screw quantity Color Torque M2 x 5 mm flat head nylok coated 2 Black 1 6 kgfcm Remove the LCD front bezel in the direction shown by arrows Pl 55 d IdeaPad S205s Hardware Maintenance Manual 1150 LCD panel LCD cable and hinges For access remove these FRUs in order e 1010 Battery pack on page 34 1020 Dummy card on page 35 e 1040 Keyboard on page 37 e 1050 Base cover on page 39 e 1060 PCI Express Mini Card for wireless LAN on page 42 e 1070 LCD unit on page 44 e 1140 LCD front bezel on page 55 Figure 15 Removal steps of LCD panel LCD cable and hinges Remove four screws W detach the integrated camera connector in the direction shown by arrow PB and then remove the LCD panel in the direction shown by arrow E Step Screw quantity Color Torque M2 x 3 mm flat head nylok coated 4 Black 1 6 kgfcm 56 Lenovo IdeaPad S205s Figure 15 Removal steps of LCD panel LCD cable and hinges continued Remove four screws EM and then detach the hinges in the direction shown by arrows El Step Screw quantity Color Torque M2 x 2 5 mm flat head nylok coated 4 White 1 6 kgfcm When installing Make sure that the connector is attached firmly Note The LCD cables are attached to the LCD panel by a metal connector Peel off the adhesive tape and detach the metal connector in the direction shown by arrow D yd i ES
35. ernational English Swiss Slovenian Slovak Icelandic Belgian Four Nordic countries Hungarian Hebrew Greek Dutch Czech Japanese Brazilian Arabic German French Russian Traditional Chinese Korean French amp English Latin Portuguese Thai Turkish Spanish Italian U K English English Czech Slovakia P N 25013514 25010563 25010564 25010565 25010566 25010567 25010568 25010569 25010570 25010571 25010572 25010573 25010574 25010575 25010576 25010577 25010578 25010579 25010580 25010581 25010582 25010678 25010679 25010680 25010681 25010682 25010683 25010684 25010685 25010686 25010687 25011162 Lenovo IdeaPad S205s 67 d IdeaPad S205s Hardware Maintenance Manual 68 Language ALPS Table 6 Parts list Keyboard continued Portuguese Bulgarian International English Swiss Slovenian Slovak Icelandic Belgian Four Nordic countries Hungarian Hebrew Greek Dutch Czech Japanese Brazilian Arabic German French Russian Traditional Chinese Korean French amp English Latin Thai Turkish Spanish Italian U K English English Czech Slovakia P N 25010606 25010607 25010608 25010609 25010610 25010611 25010612 25010613 25010614 25010615 25010616 25010617 25010618 25010619 25010620 25010621 25010622 25010623 25010624 25010625 25010626 25010627 25010628 25010629 25010630 25010631 25010632 25010633 25010634 25010635 25011167 Lenovo IdeaPad S
36. g the antenna boards release the cables from the cable guide and then remove the antenna assembly in the direction shown by arrows Bl When installing Route the antenna cables along the cable guides and secure the antenna boards with adhesive tapes As you route the cables make sure that they are not subjected to any tension Tension could cause the cables to be damaged by the cable guides or a wire to be broken 99 d IdeaPad S205s Hardware Maintenance Manual Front view W Integrated camera Built in microphone Wireless module antennas Power button OneKey Rescue System button al System status indicators Note For the description of each indicator see Status indicators on page 29 Touchpad 60 Lenovo IdeaPad S205s Right side view ll Headphone jack Microphone jack Integrated wireless device switch HDMI port USB port fal Kensington slot RJ 45 port Bottom and Left side view BM Memory card slot Fan louvers eSATA USB combo port VGA port AC power adapter jack D Battery latch manual Battery pack El SIM card slot selected models only El Battery latch spring loaded Speakers 61 d IdeaPad S205s Hardware Maintenance Manual Parts ist WE This section presents the following service parts Overall on page 63 e LCD FRUS on page 65 e Keyboard on page 67 Miscellaneous parts on page 69 AC adapters on page 70 Power cords on page 71
37. hot it may not be able to be charged Remove it from the computer and leave it at room temperature for a while After it cools down reinstall and recharge it To check the battery pack follow the steps below 1 Turn off the computer 2 Remove the battery pack and measure the voltage between battery terminals 1 and 7 See the following figure Terminal Voltage V DC 0 to 14 Ground 3 If the voltage is less than 11 0 V DC the battery pack has been discharged Note Recharging will be continued for at least 3 hours even though the indicator does not light on If the voltage is still less than 11 0 V DC after recharging replace the battery 4 f the voltage is more than 11 0 V DC measure the resistance between battery terminals 5 and 7 The resistance must be 4 to 30 KO If the resistance is not correct replace the battery pack If the resistance is correct replace the system board Related service information 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 06000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 This chapter presents th
38. ific environment Trademarks The following terms are either registered trademarks or trademarks of Lenovo in the United States and or other countries Lenovo Lenovo logo IdeaPad VeriFace OneKey Rescue OneKey Recovery OneKey Antivirus APS Power Express Energy Management and ReadyComm The following terms are trademarks of Microsoft Corporation in the United States other countries or both Windows Windows Vista Windows 7 The following are trademarks of Intel Corporation or its subsidiaries in the United States other countries or both Intel Intel Core 2 Duo Other company product or service names may be the trademarks or service marks of others 75
39. ift the keyboard a little detach the connector in the direction shown by arrows El and then remove the keyboard E When installing Make sure that the FPC connector is attached firmly 38 Lenovo IdeaPad S205s 1050 Base cover For access remove these FRUs in order e 1010 Battery pack on page 34 e 1040 Keyboard on page 37 Figure 5 Removal steps of base cover Remove four screws I Step Screw quantity Color Torque El M2 x 5 mm flat head nylok coated 4 Black 1 6 kgfcm 39 d IdeaPad S205s Hardware Maintenance Manual Figure 5 Removal steps of base cover continued Remove eight screws EM on the bottom Remove the base cover in the direction shown by arrow E Step Screw quantity Color Torque M2 x 5 mm flat head nylok coated 8 Black 1 6 kgfcm 40 Lenovo IdeaPad S205s Note Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds When you replace the base cover you need to apply the following label The following labels need to be peeled off from the old base cover and need to be put on the new base cover PAINT Label DEVICE Label FOR SYSTEM SYSTEM BARCODE Label LAN ID Label COA Label Rating Label For some models you also need to apply one or two FCC labels Check the old base cover if it has one or two FCC labels find duplicates of them in the label kit and apply them to the new base cover For the locati
40. information about replacing RoHS compliant TEE 18 General checkout 19 What to UO first A 20 Power system checkout 21 Checking the AC adapter 21 Checking operational charging 21 Checking the battery pack 22 Related service information 23 Restoring the factory contents by using OneKey Recovery cooccccccccccoccnoncccnnccnonononancnons 23 Restore of factory default 23 USING fe TT 23 See 24 Power on password E 24 Supervisor password cooocccccccccccnonccncccnnnncnnnnnnnnos 24 Power management eese 25 Screen blank mode sess 25 Sleep standby mode 25 Hibernation mode Reb iatis 26 Lenovo IdeaPad S205s 27 Specifications T R 27 Status indicators EE 29 Fn key combinations al FRU replacement notices 32 Screw notices STRUM 32 Removing and replacing an FRU 33 AA 34 1020 Dummy card uscite ta rna YA 35 TOJO SIM Card c 36 1040 Keyboard 37 1050 Base COVBlO ie teren grengen deni ei 39 1060 PCI Express Mini Card for wireless LAN 42 A r 44 1080 Hard disk drive HDD 46
41. it SZ SL SKYFI BEKLE BHBLEYVITSZAILEBSVET La bateria de repuesto es una bateria de litio y puede provocar incendios explosiones o quemaduras graves No la recargue ni quite el conector polarizado ni la desmonte ni caliente por encima de los 100 C 212 F ni la incinere ni exponga el contenido de sus celdas al agua Des chela tal como dispone la normativa local Safety information Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands immediately wash the affected areas with water at least for 15 minutes Seek medical care if any symptoms caused by the fluid are present after washing Si le panneau d affichage a cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide rincez les abondamment pendant au moins quinze minutes Consultez un m decin si des sympt mes persistent apres le lavage Die Leuchtstoffr hre im LCD Bildschirm enthalt Quecksilber Bei der Entsorgung die rtlichen Bestimmungen f r Sonderm ll beachten Der LCD Bildschirm besteht aus Glas und kann zerbrechen wenn er unsachgem h behandelt wird oder der Computer auf den Boden f llt Wenn der Bildschirm besch digt ist und die darin befindliche Fl ssigkeit in Kontakt mit Haut und Augen gerat sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgesp lt und bei Beschwerden anschlieBend ein Arzt aufgesucht werden y3oa N2 JOIN TIN 21om 11 LCD 521597
42. items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use Before checking problems with the computer determine whether the damage is covered under the warranty by referring to the following list The following are not covered under warranty LCD panel cracked from the application of excessive force or from being dropped Scratched cosmetic parts Distortion deformation or discoloration of the cosmetic parts Plastic parts latches pins or connectors that have been cracked or broken by excessive force e Damage caused by liquid spilled into the system e Damage caused by the improper insertion of a PC Card or the installation of an incompatible card Improper disc insertion or use of an optical drive Diskette drive damage caused by pressure on the diskette drive cover foreign material in the drive or the insertion of a diskette with multiple labels e Damaged or bent diskette eject button Fuses blown by attachment of a nonsupported device Forgotten computer password making the computer unusable Sticky keys caused by spilling a liquid onto the keyboard Use of an incorrect AC adapter on laptop products The following symptoms might indicate damage caused by nonwarranted activities Missing parts might be a symptom of unauthorized service or modification Ifthe spindle of a hard disk drive becomes noisy it may have been s
43. ive or apply any physical shock to it The hard disk drive is sensitive to physical shock Improper handling can cause damages and permanent loss of data Before removing the drive suggest the customer to backup all the information on it 1f possible Never remove the drive while the system is operating or is in suspend mode Figure 8 Removal steps of hard disk drive Note Remove two screws Wl and then remove the hard disk drive in the direction shown by arrow Pl Step Screw quantity Color Torque E M2 x 5 mm flat head nylok coated 2 Black 1 6 kgfcm 46 Lenovo IdeaPad S205s 1090 DIMM For access remove these FRUs in order e 1010 Battery pack on page 34 1020 Dummy card on page 35 e 1040 Keyboard on page 37 e 1050 Base cover on page 39 e 1060 PCI Express Mini Card for wireless LAN on page 42 e 1070 LCD unit on page 44 Figure 9 Removal steps of DIMM Release the two latches on both edges of the socket at the same time in the direction shown by arrows Bl and then unplug the DIMM in the direction shown by arrow E1 When installing Insert the notched end of the DIMM into the socket Push the DIMM firmly and pivot it until it snaps into the place Make sure that it is firmly fixed in the slot and difficult to be moved 47 d IdeaPad S205s Hardware Maintenance Manual 1100 Fan assembly and heat sink assembly For access remove this FRU e 1010 Battery
44. lenovo IdeaPad S205s Hardware Maintenance Manual Note Before using this information and the product it supports be sure to read the general information under Notices on page 74 First Edition October 2011 Copyright Lenovo 2011 All rights reserved LIMITED AND RESTRICTED RIGHTS NOTICE If data or software is delivered pursuant a General Services Administration GSA contract use reproduction or disclosure is subject to restrictions set forth in Contract No GS 35F 05925 2011 Lenovo 00000000000O0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Contents 00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 About this TT IR iv Safety information 1 General safety sese 2 Electrical safety pensaria 3 Safety inspection guide 5 Handling devices that are sensitive to electrostatic dscharge 6 Grounding requirements 6 Safety notices multilingual translations 7 Laser compliance statement 14 Important service information 16 Strategy for replacing FRUS 16 Strategy for replacing a hard disk drive 17 Important notice for replacing a system board 17 Important
45. m Korea 145000590 LINETEK LS15 HO5VV F LP E04A 1m Australia 145000589 e LINETEK LS15 HO3VV F LP 23A 1m Taiwan 145000588 LINETEK LS15 VCTF LP 53 1m Japan 145000587 LINETEK LS15 VCTF LP 54 1m Africa 145000586 e LINETEK LS15 HO3VV F PE 364 1m CE 145000585 e LINETEK LP 34 HO3VV F LS15 1m CCC 145000538 e VOLEX GB10S3 RVV 300 500 VAC5S 1m UL 145000537 Volex US15S3 SPT 2 VAC5S 1m UK 145000605 e VOLEX MP5004 HO3VV F VAC5S 1m Indian 145000536 e VOLEX IA6A3 19694 VAC5S 1m 1 d IdeaPad S205s Hardware Maintenance Manual 12 Table 9 Parts list 3 pin power cords continued Region Switzerland e VOLEX MP232 H03VV F VAC5S 1m Italy e VOLEX IT10S3 HO3VV F VAC5S 1m Denmark e VOLEX MP233D HO03VV F VAC5S 1m Korea e VOLEX M2511 KETI IEC VAC5S 1m Australia e VOLEX AU10S3 HO3VV F VAC5S 1m Taiwan e VOLEX TW15CS3 VCTF VAC5S 1m Japan e VOLEX VAC5S VCTF M755 1m Argentina e VOLEX VA2073 H03VV F VAC5S 1m Brazil e VOLEX CH10S3 HO3VV F VAC5S 1m Israel e VOLEX SI16S3 HO3VV F VAC5S 1m CE e VOLEX M2511 HO3VV F VAC5S 1m CCC Longwell LSG 31 RVV300 300 LS 18 1m Argentina e Longwell LP 24 H03VV F LS 18 1m Danmark e Longwell LP 40 HO3VV F LS 18 1m Switzerland e Longwell LP 37 HO3VV F LS 18 1m Brazil e Longwell LP 46 HO3VV F LS 18 1m Israel e Longwell LP 41 HO3VV F LS 18 1m UL Longwell LP 30B SPT 2 18AWG LS 18 1m UK Longwell LP 61L HO3VV F LS 18 1m Indian Longwell LP 67 BIS LS 18 1m
46. mputer has three power management modes screen blank sleep standby and hibernation Screen blank mode If the time set on the Turn off monitor timer in the operating system expires the LCD backlight turns off You can also turn off the LCD backlight by pressing Fn F2 To end screen blank mode and resume normal operation press any key Sleep standby mode When the computer enters sleep standby mode the following events occur in addition to what occurs in screen blank mode e The LCD is powered off e The hard disk drive is powered off e The CPU stops To enter sleep standby mode press Fn F1 In certain circumstances the computer goes into sleep standby mode automatically e f a suspend time has been set on the timer and the user does not do any operation with the keyboard the hard disk the parallel connector or the diskette drive within that time f the battery indicator starts blinking indicating that the battery power is low Alternatively if Hibernate when battery becomes low has been selected in the Power Management Properties window the computer goes into hibernation mode To cause the computer to return from sleep standby mode and resume the operation do one of the following Press the Fn key Open the lid Turn on the power switch Also in the following event the computer automatically returns from sleep standby mode and resumes the operation The time set on the
47. n adatta potrebbe determinare l incendio o l esplosione della batteria stessa Ti 7U otnmic ibiE Eo yzvbxgRgivBAMAEIvOCOS602 595 ET Lat PASITO PEE KERO POOR dza bsu5 cHERUCQDARvCQEsAv y7 EBNX 2 Beidio BRO FRAN ES T 725v Bic VAR HON YT IER LC ESV Bok y 7 VU EEE ASTUR KUED RBELEVTSZILRBHVET Algunas bater as de reserva contienen una pequefia cantidad de n quel y cadmio No las desmonte ni recargue ni las eche al fuego o al agua ni las cortocircuite Des chelas tal como dispone la normativa local Utilice s lo bater as que se encuentren en la lista de piezas La utilizaci n de una bater a no apropiada puede provocar la ignici n o explosi n de la misma Safety information Safety notice 3 A DANGER The battery pack contains small amounts of nickel Do not disassemble it throw it into fire or water or short circuit it Dispose of the battery pack as required by local ordinances or regulations Use only the battery in the appropriate parts listing when replacing the battery pack Use of an incorrect battery can result in ignition or explosion of the battery La batterie contient du nickel Ne la d montez pas ne l exposez ni au feu ni l eau Ne la mettez pas en court circuit Pour la mettre au rebut conformez vous la r glementation en vigueur Lorsque vous remplacez la batterie veillez n utiliser que les modeles cit s dans la liste de pieces d tach es ad quate En effet une batterie inappro
48. noneb3oBaHune 3JleMeHTOB HACTPONKU N BbINOJHEHNe NPOLWe AYP VHbIX HeM yka3aHo 3necb MOX T MPUBECTH K OT1aCHOMy paanaunoHHomy o6 ryueuuio Pouzitie kontr l prav alebo inych vykonani od inych v robcov ako je v tomto pecifikovan mohlo by mat za n sledok nebezpecenstvo vystavenia sa vyZiarovaniu RECESO BRRIC 2HR HE ECL FIRE o KBE LP GOWN 018 23450 3 3 El uso de controles o ajustes o la ejecuci n de procedimientos distintos de los aqui especificados puede provocar la exposici n a radiaciones peligrosas Opening the CD ROM drive the DVD ROM drive or any other optical storage device could result in exposure to hazardous laser radiation There are no serviceable parts inside those drives Do not open 14 Safety information A CD ROM drive a DVD ROM drive or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode Note the following A DANGER Emits visible and invisible laser radiation when open Do not stare into the beam do not view directly with optical instruments and avoid direct exposure to the beam Radia o por raio laser ao abrir Nao olhe fixo no feixe de luz n o olhe diretamente por meio de instrumentos ticos e evite exposi o direta com o feixe de luz FANSAROtCANN IDU gt FORRES AIS HS BBE BOLDER ZF o Rayonnement laser si carter ouvert Evitez de fixer le faisceau de le regarder directement avec des instruments optiques ou de vous expo
49. oes not insulate you when working with live electrical currents Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges Do not use such kind of mat to protect yourself from electrical shock Find the room emergency power off EPO switch disconnecting the switch or electrical outlet If an electrical accident occurs you can then operate the switch or unplug the power cord guickly Do not work alone under hazardous conditions or near the eguipment that has hazardous voltages Disconnect all power before Performing a mechanical inspection Working near power supplies Removing or installing main units Before you start to work on the machine unplug the power cord If you cannot unplug it ask the customer to power off the wall box that supplies power to the machine and to lock the wall box in the off position If you need to work on a machine that has exposed electrical circuits observe the following precautions Ensure that another person familiar with the power off controls is near you Attention Another person must be there to switch off the power if necessary Use only one hand when working with powered on electrical eguipment keep the other hand in your pocket or behind your back Attention An electrical shock can occur only when there is a complete circuit By observing the above rule you may prevent a current from passing through your body
50. on of each label refer to the following figure EA GAIA E 41 d IdeaPad S205s Hardware Maintenance Manual 42 1060 PCI Express Mini Card for wireless LAN For access remove these FRUs in order e 1010 Battery pack on page 34 e 1020 Dummy card on page 35 e 1040 Keyboard on page 37 e 1050 Base cover on page 39 Figure 6 Removal steps of PCI Express Mini Card for wireless LAN TAA S AOO gt i a Mim Disconnect two wireless LAN cables black white in the direction shown by arrow Bl and then remove one screw B In step ll unplug the jacks by using the removal tool antenna RF connector P N 08K7159 or pick up the connectors with your fingers and gently unplug them in the direction shown by arrow Notes wireless LAN card has 2 cables in step Bl wireless LAN card in some models may have 3 cables in step Bl Step Screw quantity Color Torque M2 x 3 mm flat head nylok coated 1 Black 1 6 kgfcm Lenovo IdeaPad S205s Figure 6 Removal steps of PCI Express Mini Card for wireless LAN continued Remove two cards in the direction shown by arrow Kl When installing In models with a wireless LAN card that has two antenna connectors plug the black cable 1st MAIN into the jack labeled 1 and the white cable 2nd AUX into jack labeled 2 on the card In models with
51. on siano sparse all interno dell elaboratore Verificare ci scuotendo l elaboratore e prestando attenzione ad eventuali rumori eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi FRU DZH IVCA DREAN DANZ TAC NK COMO 372 dE Lv MILD ER IY es ZONE CRRA CWRW FE HER L T lt s AULA MER DICIA APRA O TO WF HAF A EBB URW ATED OE FT EBRO ABRA IY a ORRATZA AZ LEN ET Antes de encender el sistema despues de sustituir una FRU compruebe que todos los tornillos muelles y dem s piezas peque as se encuentran en su sitio y no se encuentran sueltas dentro del sistema Compru belo agitando el sistema y escuchando los posibles ruidos que provocar an Las piezas met licas pueden causar cortocircuitos el ctricos d IdeaPad S205s Hardware Maintenance Manual Safety notice 2 A DANGER Some standby batteries contain a small amount of nickel and cadmium Do not disassemble a standby battery recharge it throw it into fire or water or short circuit it Dispose of the battery as required by local ordinances or regulations Use only the battery in the appropriate parts listing Use of an incorrect battery can result in ignition or explosion of the battery Certaines batteries de secours contiennent du nickel et du cadmium Ne les d montez pas ne les rechargez pas ne les exposez ni au feu ni l eau Ne les mettez pas en court circuit Pour les mettre au rebut conformez vous la r glementa
52. ool bag Always use new screws Use a torque screwdriver if you have one Tighten screws as follows Plastic to plastic Turn an additional 90 after the screw head touches the surface of the plastic part more than 90 E V Cross section Logic card to plastic Turn an additional 180 after the screw head touches the surface of the logic card more than 180 E Cross section Torque driver If you have a torque screwdriver refer to the Torque column for each step Make sure that you use the correct screws If you have a torque screwdriver tighten all screws firmly to the torque shown in the table Never use a screw that you removed Use a new one Make sure that all screws are tightened firmly Ensure torque screwdrivers are calibrated correctly following country specifications ER Lenovo IdeaPad S205s Removing and replacing an FRU This section presents exploded figures with the instructions to indicate how to remove and replace the FRU Make sure to observe the following general rules 1 Do not attempt to service any computer unless you have been trained and certified An untrained person runs the risk of damaging parts 2 Before replacing any FRU review FRU replacement notices on page 32 3 Begin by removing any FRUs that have to be removed before the failing FRU Any of such FRUs are listed at the top of the page Remove them in th
53. ower cord for a Athird wire ground connector in good condition Use a meter to measure third wire ground continuity for 0 1 ohm or less between the external ground pin and the frame ground b The power cord should be the type specified in the parts list c Insulation must not be frayed or worn 4 Check for cracked or bulging batteries Remove the cover 6 Check for any obvious non Lenovo IdeaPad alterations Use good judgment as to the safety of any non Lenovo IdeaPad alterations 7 Check inside the unit for any obvious unsafe conditions such as metal filings contamination water or other liquids or signs of fire or smoke damage 8 Check for worn frayed or pinched cables 9 Check that the power supply cover fasteners screws or rivets have not been removed or tampered with e d IdeaPad S205s Hardware Maintenance Manual Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits ICs should be considered sensitive to electrostatic discharge ESD ESD damage can occur when there is a difference in charge between objects Protect against ESD damage by equalizing the charge so that the machine the part the work mat and the person handling the part are all at the same charge Notes 1 Use product specific ESD procedures when they exceed the requirements noted here Make sure that the ESD protective devices you use have been certified IS
54. pri e risque de prendre feu ou d exploser Akkus enthalten geringe Mengen von Nickel Sie d rfen nicht zerlegt wiederaufgeladen kurzgeschlossen oder Feuer oder Wasser ausgesetzt werden Bei der Entsorgung die rtlichen Bestimmungen f r Sonderm ll beachten Beim Ersetzen der Batterie nur Batterien des Typs verwenden der in der Ersatzteilliste aufgef hrt ist Der Einsatz falscher Batterien kann zu Entz ndung oder Explosion f hren Donn Du n30p ms 5555 NIDA TANI Town n5510n VINO nx 2595 yx 09999777 NN DIVI V YDYN 35 YN 07722 IN UND INN nypnn D Du VINI ADDON ADIN INIA NIDV0A p Wnnwn v n nmpnn tuom NINA ta DONNA OPINA nn w53 AWaINA 212 DION NI AINA WYW 22100 TINN ITN W msisiann IN ANAT 01537 La batteria contiene piccole quantita di nichel Non smontarla gettarla nel fuoco o nell acqua n cortocircuitarla Smaltirla secondo la normativa in vigore DPR 915 82 successive disposizioni e disposizioni locali Quando si sostituisce la batteria utilizzare soltanto 1 tipi inseriti nell appropriato Catalogo parti L impiego di una batteria non adatta potrebbe determinare l incendio o l esplosione della batteria stessa AvyTU ua A CH ROH YTVBBENTWET AVTV eyy AMLIU KERO FER IED 7a b SWeuwc lt cv RIT V No ORR Hie CH MA BIB ORBIS RANTE T ES NYT UV 9 NYT BRATS LE EL MIRA Y VARITHS RyTV RV SEALS EE Roky 7 UAEM Ll v7 y BEKLE R EL TCU 3 S EDU ES Las bater as contienen pequefias cantidades de n
55. remaining power of the battery is less than 5 of its capacity Blinking amber 100ms off 3 2s on Amber The battery is being charged with the remaining power between 5 and 20 of its capacity The computer is operating on battery power with the remaining power between 5 and 20 of its Capacity Blinking white White White Off White The battery is being charged with the remaining power between 20 and 80 of its capacity The remaining power of the battery is more than 80 of its capacity or the computer is operating on battery power with the remaining power between 20 and 80 of its capacity Any one of the wireless devices WLAN Bluetooth WWAN is enabled All the wireless devices WLAN Bluetooth WWAN are disabled Data is being read from or written to the hard disk drive When this indicator is on do not put the computer into standby mode or turn off the computer Note Do not move the system while the white drive in use light is on Sudden physical shock could cause drive errors White The touchpad is disabled To enable or disable the touchpad press and hold the Fn key and press the F6 key Lenovo IdeaPad S205s En key combinations key combinations The following table shows the function of each combination of Fn with a function key Table 3 Fn key combinations Key combination Fn Esc Fn F1 Fitz Fn F3 En F5 Fn Fo Fn F7 Fn F8 Ent FO Fn F
56. rench German Hebrew Italian Japanese and Spanish Safety notice 1 Before the computer is powered on after FRU replacement make sure all screws springs and other small parts are in place and are not left loose inside the computer Verify this by shaking the computer and listening for rattling sounds Metallic parts or metal flakes can cause electrical shorts Avant de remettre l ordinateur sous tension apr s remplacement d une unit en client le v rifiez que tous les ressorts vis et autres pi ces sont bien en place et bien fix es Pour ce faire secouez l unit et assurez vous qu aucun bruit suspect ne se produit Des pi ces m talliques ou des copeaux de m tal pourraient causer un court circuit Bevor nach einem FRU Austausch der Computer wieder angeschlossen wird mu sichergestellt werden daB keine Schrauben Federn oder andere Kleinteile fehlen oder im Geh use vergessen wurden Der Computer mu gesch ttelt und auf Klapperger usche gepr ft werden Metallteile oder splitter k nnen Kurzschl sse erzeugen NT v FRU nadnn ANNI a2awnn n NIYIN 395 DNI DANN DOD OPIN D SPspn 0 03n 2DW NTI 72 32wnn n TINA m 0 gt W0 n DIN 001703 pw 5 HDI 2Wn2 AWN NN 20202 W NNI b 22wn DAPI 01122 DINIY NINN 33V IN PIN Prima di accendere l elaboratore dopo che 6 stata effettuata la sostituzione di una FRU accertarsi che tutte le viti le molle e tutte le altri parti di piccole dimensioni siano nella corretta posizione e n
57. resume timer elapses Note The computer does not accept any input immediately after it enters sleep standby mode Wait a few seconds before taking any action to reenter operation mode 25 d IdeaPad S205s Hardware Maintenance Manual 26 Hibernation mode In hibernation mode the following occurs The system status RAM VRAM and setup data are stored on the hard disk The system is powered off To cause the computer to enter hibernation mode follow the steps below f you are using the ACPI operating system and have defined one of the following actions as the event that causes the system to go into hibernation mode perform that action Closing the lid Pressing the power button Also the computer goes into hibernation mode automatically in either of the following conditions e f a hibernation time has been set on the timer and if the user does not do any operation with the keyboard the hard disk drive the parallel connector or the diskette drive within that time Ifthe timer conditions are satisfied in suspend mode When the power is turned on the computer returns from hibernation mode and resumes operation The hibernation file in the boot record on the hard disk drive is read and system status is restored from the hard disk drive Lenovo IdeaPad S205s 00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
58. s a CD ROM drive or a DVD ROM drive Such devices are also sold separately as options If one of these drives is installed it is certified in the U S to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations DHHS 21 CFR Subchapter J for Class 1 laser products Elsewhere the drive is certified to conform to the requirements of the International Electrotechnical Commission IEC 825 and CENELEC EN 60 825 for Class 1 laser products If a CD ROM drive a DVD ROM drive or another laser device is installed note the following N CAUTION Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure O uso de controles ajustes ou desempenho de procedimentos diferentes daqueles aqui especificados pode resultar em perigosa exposi o radia o Aute BR HAE TEA E rh ASSURER Pour viter tout risque d exposition au rayon laser respectez les consignes de r glage et d utilisation des commandes ainsi que les proc dures d crites Werden Steuer und Einstellelemente anders als hier festgesetzt verwendet kann gefahrliche Laserstrahlung auftreten Az itt el rt elj r sokt l be ll t sokt l s vez rl sekt l elt rni a l zersug rz s vesz lye miatt kock zatos L utilizzo di controlli regolazioni o l esecuzione di procedure diverse da quelle specificate possono provocare l esposizione a Vc
59. ser au rayon Laserstrahlung bei ge ffnetem Ger t Nicht direkt oder ber optische Instrumente in den Laserstrahl sehen und den Strahlungsbereich meiden Kinyitaskor l zersug r Ne n zzen bele se szabad szemmel se optikai eszk z kkel Ker lje a sug rnyal bbal val rintkez st Aprendo l unit vengono emesse radiazioni laser Non fissare il fascio non guardarlo direttamente con strumenti ottici e evitare l esposizione diretta al fascio OrkpbiBas 6epervrecb naaepHoro u3snyyeHua He cworpure Ha nys He paarnsnbiBalire ero C MOMOLUBIO ONTUYECKUX MHCTPYMEHTOB a TaKXe uz6erante npaMoro BO3nelcrBus JiaaepHOro Jyua Ked je laserova jednotka otvorena Vyhnite sa priamemu poh adu a nehladte priamo s optick mi n strojmi do l ta a vyhnite sa priamemu vystaveniu l ov BD ELY 26 BASES FERRE LOD TE TERRE BO TE Ii TEM LIEV CSTE Radiaci n l ser al abrir No mire fijamente ni examine con instrumental ptico el haz de luz Evite la exposici n directa al haz 15 d IdeaPad S205s Hardware Maintenance Manual 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 060000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
60. t applications where malfunction may result in injury or death to persons The information contained in this document does not affect or change Lenovo product specifications or warranties Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties All information contained in this document was obtained in specific environments and is presented as an illustration The result obtained in other operating environments may vary Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you Any references in this publication to non Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites The materials at those Web sites are not part of the materials for this Lenovo product and use of those Web sites is at your own risk Notices Any performance data contained herein was determined in a controlled environment Therefore the result obtained in other operating environments may vary significantly Some measurements may have been made on development level systems and there is no guarantee that these measurements will be the same on generally available systems Furthermore some measurements may have been estimated through extrapolation Actual results may vary Users of this document should verify the applicable data for their spec
61. tion en vigueur Lorsque vous remplacez la pile de sauvegarde ou celle de l horloge temps r el veillez n utiliser que les modeles cit s dans la liste de pi ces d tach es ad quate Une batterie ou une pile inappropri e risque de prendre feu ou d exploser Die Bereitschaftsbatterie die sich unter dem Diskettenlaufwerk befindet kann geringe Mengen Nickel und Cadmium enthalten Sie darf nicht zerlegt wiederaufgeladen kurzgeschlossen oder Feuer oder Wasser ausgesetzt werden Bei der Entsorgung die rtlichen Bestimmungen f r Sonderm ll beachten Beim Ersetzen der Bereitschafts oder Systembatterie nur Batterien des Typs verwenden der in der Ersatzteilliste aufgef hrt ist Der Einsatz falscher Batterien kann zu Entz ndung oder Explosion f hren mop 5555 NI mon ANIA MID MINIMA NINO 25355 yx DDT Y SW IN WN ADIN PIVAT WINN NMN PYDI n5510n DN PIDI U INN 5395 IN 09199 v Dunn DPINA mynn 59 WINI t p5nn np AMAIA n551023 p wnnwn 2129 MINI NI 022103 WIV nmxnman n2210n 2U mssann IN ANAT 01535 Alcune batterie di riserva contengono una piccola quantit di nichel e cadmio Non smontarle ricaricarle gettarle nel fuoco o nell acqua n cortocircuitarle Smaltirle secondo la normativa in vigore DPR 915 82 successive disposizioni e disposizioni locali Quando si sostituisce la batteria dell RTC real time clock o la batteria di supporto utilizzare soltanto 1 tipi inseriti nell appropriato Catalogo parti L impiego di una batteria no
62. ubjected to excessive force or dropped 20 General checkout Power system checkout system checkout To verify a symptom follow the steps below Turn off the computer Remove the battery pack Connect the AC adapter Make sure that power is supplied when you turn on the computer Turn off the computer Disconnect the AC adapter and install the charged battery pack Make sure that the battery pack supplies power when you turn on the computer oe Du i If you suspect a power problem see the appropriate one of the following power supply checkouts e Checking the AC adapter on page 21 e Checking operational charging on page 21 Checking the battery pack on page 22 Checking the AC adapter You are here because the computer fails only when the AC adapter is used e If the power on indicator does not turn on check the power cord of the AC adapter for correct continuity and installation e If the computer does not charge during operation go to Checking operational charging To check the AC adapter follow the steps below 1 Unplug the AC adapter cable from the computer 2 Measure the output voltage at the plug of the AC adapter cable See the following figure Note Output voltage for the AC adapter pin No 2 may differ from the one you are servicing 3 If the voltage is not correct replace the AC adapter 4 lf the voltage is acceptable do the following Replace the system board
63. ur computer the system will enter the user interface for system recovery automatically Please follow the prompt to insert the backup discs to complete the whole recovery process Note The recovery process might take up to 2 hours Passwords 24 As many as two passwords may be needed for any Lenovo IdeaPad computer the power on password POP and the supervisor password SVP If any of these passwords has been set a prompt for it appears on the screen whenever the computer is turned on The computer does not start until the password is entered Exception If only an SVP is installed the password prompt does not appear when the operating system is booted Power on password A power on password POP protects the system from being powered on by an unauthorized person The password must be entered before an operating system can be booted Supervisor password A supervisor password SVP protects the system information stored in the BIOS Setup Utility The user must enter the SVP in order to get access to the BIOS Setup Utility and change the system configuration Attention If the SVP has been forgotten and cannot be made available to the servicer there is no service procedure to reset the password The system board must be replaced for a scheduled fee Related service information Power management management Note Power management modes are not supported for APM operating system To reduce power consumption the co

Lenovo S205S User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents