Installation Guide - U-Line
Contents
1. holes See Figure 32 Drill Holes and Mount Anti Tip Brackets to Floor Marks on Floor Figure 30 4 Remove the unit Using a square extend a centerline 20 1 4 toward the back wall See Figure 31 At the back of the centerline mark a line that measures 11 1 16 to the left and right This line serves as the Back back edge for the Anti Tip Brackets and its furthest 3 anna points mark the outer edge of each bracket OP Front Note Instructions are shown for built in installation Use of Unit same dimensions for free standing installation Figure 32 6 Use a 1 8 drill to make two starter holes and fasten the Anti Tip Brackets to the floor using the screws provided NCAUTION Other hardware is required for floors made of materials other than wood 7 Place the unit back into position making sure the feet engage the Anti Tip Brackets properly Check the alignment of the lines made on the floor in Step 3 with the position of the front feet to ensure proper positioning www U LineService com 14 02 2005 TM Installation Troubleshooting Q Problem The door remains open unless it is pushed closed A Z Solution The hinges should be self closing when the door is open approximately 8 If this is not the case make sure the closers at the bottom of the hinge pin are clean greased and installed correctly2. see Back View 4 Drill holes for pivot plate mounts see Figure 15 Back View 5 16 diameter x 1 2 deep from the routed surface CAUTION Be careful not to drill too deep Drilling holes too deep may destroy your door frame 5 Drill hole for upper door hinge top of frame see Figure 15 Top View 0 177 diameter 16 drill x 11 16 deep 6 Drill hole for lower door hinge see Figure 15 Bottom View 5 16 diameter x 1 4 deep CAUTION It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed www U LineService com T UFLINE 8C ORPORATION Installation Instructions Preparing Door Note Door is not attached It is in a separate box inside the unit box and taped to the unit 1 Lay door on a clean flat surface with the gasket facing up X 2 Pull gasket completely out Door of the groove Start in the Figure 16 middle and pull outward moving toward the edge see Figure 16 This may take some force Note Lay gasket flat on a clean surface to avoid disturbing interior magnet Checking Overlay Fit M oS Not Fully Seated Figure 17 Little or No Gap Objectional Gap 1 Turn door over and lay overlay frame on front side of door Make sure frame is fully seated on all four sid
3. 3 4 The door frame must not weigh more than 20 Ibs 1 Create an overlay frame to the dimensions shown in Figure 13 Relief Notch for Pivot Plate Right Hand Hinge Shown Rear View of Wood Frame Figure 13 IMPORTANT Rear View of wood frame for right hand hinge shown Use mirror image for left hand hinges 02 2005 N Typical routing dimensions are shown in Figure 14 1 1 8 1 13 16 11 16 Ref Y 7 16 Ref A gt j 5 32 3 8 Figure 14 3 Create a relief for pivot plate by cutting notch in top corner and coinciding back corner of overlay frame Refer to Figure 15 for exact specifications 0 177 Dia 16 Drill X 11 16 Deep Door Bottom 5 16 Dia X 1 4 Deep Chamfer 1 32 x 45 Top View Bottom View lt 13 16 gt x 1 2 Deep Back View Side View Figure 15 02 2005 2075WC 2075WCOL Wine Captain 2 1 4 T UFLINE CORPORATION Route notch in top corner of overlay frame as shown see Top and Side Views Top of notch is entire depth of frame front to back Width 13 16 Depth 1 8 Route notch in backside of top corner of overlay frame see Back and Side Views Width 13 16 Depth 1 8 Height 1 17 32 from top edge of frame less 1 8 for depth of notch on top of frame Radius of corner notch 1 8
4. Also re check leveling from front to back of the unit and readjust if necessary Make sure that pivot plate is installed correctly 02 2005 2075WC 2075WCOL Wine Captain 15 T UFLINE CORPORATION 9 Start Up for the First Time Initial Start Up The unit is shipped with the control preset No adjustments should be necessary at this time For information about Adjusting the Temperature Control see the User Manual Start Up Troubleshooting Q Problem Unit does not appear to turn on when plugged in A Solution Make sure outlet has power circuit breaker has not tripped Check to see that control is turned on Q Problem Light is on with door closed A 2 Solution Make sure switch located to the right of the control dial on the grille is set to OFF The Wine Captain has an interior light that is illuminated when the door is opened The light can be activated while the door is closed by depressing the switch to the ON position IMPORTANT See the User Manual s Troubleshooting Guide for more solutions www U LineService com T UFLINE CORPORATION Who to Call Service Information If the need for service arises contact the dealer from whom the unit was purchased State the Model Number and Serial Number and explain the problem The Model and Serial Number plate is located inside unit at upper right hand corner If you need to locate a service company you can go online at www U
5. Captain T U LITE 8C ORPORATION 6 Prepare Power Supply 7 Level the Unit Electrical Specifications NCAUTION Electrical installation must observe all state and local codes This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician The unit requires a grounded and polarized 115 VAC 60 Hz 15A power supply normal household current An individual properly grounded branch circuit or circuit breaker is recommended GFCI ground fault circuit interrupter is usually not required for fixed location appliances and is not recommended for your unit because a GFCI could be prone to nuisance tripping However be sure to consult your local codes See Figure 27 for recommended receptacle location Figure 27 NWARNING SHOCK HAZARD Electrical Grounding Required Never remove the round grounding prong from the plug and never use a two prong grounding adapter Never use an extension cord to connect power to the unit Go on to 7 Level the Unit 02 2005 Leveling Information Note It is recommended that the unit is level 1 Use a level to check the levelness of the Wine Captain from front to back and from side to side Level should be placed along top edge and side edge as shown see Figure 28 Figure 28 2 If the Wine Captain is not level adjust the feet on the corn
6. LineService com and search for a service company by zip code For more than four decades U Line has distinguished itself as the leader in built in undercounter ice making refrigeration and wine storage appliances Echelon SERIES Origins SERIES U Line Corporation located in Milwaukee WI is a family operated manufacturer of built in undercounter icemakers Combo icemaker refrigerators Wine Captain wine storage units refrigerators refrigerated drawers and refrigerator freezers 2005 U Line Corporation Publication No 30054E 02 2005 Rev A
7. V U LINE CORPORATION Door Swing Clearances Information Black White and Wood Overlay units have a zero clearance for the door to open 90 see Figure 3 Stainless Steel models require a minimum of 2 1 8 door clearance to accommodate the handle if the unit is installed next to a wall or similar type of structure 2 1 8 Min 90 90 Door Swing Door Swing Black White and Wood Overlay Stainless Steel Figure 3 Reversing the Door Black and White Units Only All U Line units except Stainless Steel models may be left or right hand opening The door opening is easily reversed by moving the hinge hardware to the opposite side The top hinge hardware will be used on the bottom of the other side and the bottom hinge hardware will be used on the top of the other side see Figure 4 To reverse the door 1 Remove top hinge screw pin from door 7 64 Allen wrench or Phillips screwdriver depending on your unit s construction see Figure 5 Remove door by tilting forward and lifting off bottom hinge pin www U LineService com T UFLINE CORPORATION 2 Remove plastic screw plugs 3 each top and bottom from new hinge location Do not discard see Figure 6 Screw Plugs Figure 5 Figure 6 3 Remove top hinge 3 screws reinstall hinge screw pin and remount on opposite side BOTTOM see Figure 7 4 Remove the two
8. ain TM 1 Follow Safety Precautions IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes Safety Alert Definitions Safety items throughout this guide are labeled with a Danger Warning or Caution based on the risk type A DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death NWARNING Warning means that failure to follow this safety statement could result in serious personal injury or death NCAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury property or equipment damage 02 2005 General Precautions Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide NWARNING SHOCK HAZARD Electrical Grounding Required Keep the unit unplugged throughout installation except during testing Never remove the round grounding prong from the plug and never use a two prong grounding adapter Never use an extension cord to connect power to the unit Always keep your working area dry NCAUTION Use care when moving and handling the unit Use gloves to
9. and your intended design Tools Materials Required e 7 64 Allen wrench included in 2075WCOL hardware e Screwdrivers slotted and Phillips head Sandpaper low odor water clean up quick drying finish tack cloth and if desired water based wood stain and synthetic foam brush e 3 4 inch overlay frame material cutting tools drill and bits 2075WCOL units Inspection Unwrap and inspect the unit on a flat level surface capable of supporting its entire weight Removing Protective Coating Stainless Steel Units Only When inspecting installing a Stainless Steel unit the protective coating covering the unit must be removed first Start at a corner of the unit door and pull back the protective coating to remove it from the unit door www U LineService com T UFLINE 2075WC 2075WCOL Wine Captain 8C ORPORATION After all the protective coating has been removed from the unit door clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft cloth Do NOT use abrasive cleaning agents Note If cleaning with mild detergent and warm water solution and soft cloth the unit MUST be treated with Claire Stainless Steel Polish and Cleaner or comparable product to prevent discoloration Exterior Cleaning As Required Black and White Models The door grille and cabinet may be cleaned with a mild detergent and warm wa
10. are is below surface of overlay frame Failure to do so can cause damage to overlay frame and or door Overlay frame will not sit flush to door if mounting hardware is not counter bored 02 2005 2075WC 2075WCOL Wine Captain U UFLINE CORPORATION Note The door frame is designed with a slight amount of play to square it to the overlay frame 6 Remove all traces of tape securing overlay frame to door frame 7 Starting at the corners and working toward the center push the door gasket back into place Make sure gasket is seated on all four sides Installing the Door IMPORTANT X Pivot posts must be clean Closers must also be clean and Overlay greased to ensure proper operation 1 Insert pivot post into bottom hinge making sure to Figure 20 tighten only until post is level with outside of hinge 2 Install door closer See Figure 26 on Page 12 Be sure 3 Secure the front of the door to the back of the overlay that BOSSES OF closers align with holes in hinge frame using tape on all four corners as shown in Figure 20 Make sure all four edges are aligned Pivot Post f Punch Pilot Holes for use with 6 x 1 Pan head Screws 10 Places Rear View of Door and Overlay Frame Figure 21 Figure 22 4 Place door and overlay frame on a flat clean protective surface Use the door frame hole
11. door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge see Figure 8 Door Closer Inserts Figure 8 5 Remove existing bottom hinge 3 screws and remount on opposite side TOP Remove hinge screw pin 6 Remove the plastic hole plug from the top of the door to allow the pivot pin to be inserted in the new location Install the plug into the vacated hole on the opposite side www U LineService com 2075WC 2075WCOL Wine Captain s TM 7 With bottom of door facing up remove pivot plate 2 screws flip over and remount on opposite side of door see Figure 9 Be sure angled side of plate faces center Figure 9 8 Holding door upright with top of door tilted forward place hole of door pivot plate on bottom hinge screw pin see Figure 10 9 Tilt top of door into position in top hinge and install top hinge screw pin 10 Install plastic screw plugs removed in Step 2 in old hinge holes 3 each top and bottom Figure 10 Other Site Requirements Power Supply The unit requires a grounded and polarized 115 VAC 60 Hz 15A circuit normal household current See Electrical Specifications on Page 13 Environmental Requirements The surrounding air temperature must be at least 50 F 10 C but must not exceed 110 F 40 C The unit must not be located near heat generating equipment or in direct sunlight 02 2005 Sid
12. e By Side Installation Instructions For a complete refreshment center install your 2075WC or 2075WCOL unit beside a U Line Refrigerator Ice Maker or Combo Model see Figure 11 for typical cut out Note that each Side By Side Installation will be different e Cut out width for a side by side installation is the total of the widths listed under Cut Out Dimensions in each unit s Installation Guide For example Placing a 2075 Wine Captain next to a 2015 series unit would require a cut out width of 24 3 16 15 3 16 39 3 8 Placing a 2075 Wine Captain next to a 2075 series unit would require a cut out width of 24 3 16 24 3 16 48 3 8 e No trim kit is required However 1 4 inch space needs to be maintained between the units to ensure unobstructed door swing e Units must operate from separate properly grounded electrical receptacles placed according to each unit s Electrical Specifications Typical Side By Side Cut Out e e 1 4 Space sl Between Appliances Figure 11 02 2005 2075WC 2075WCOL Wine Captain T UFLINE 8C ORPORATION 4 Prepare Racks and Door Frame The U Line Wine Captain is equipped with wood trimmed wine racks that are coated at the factory with a clear vinyl sealer which will adequately protect the wood in normal usage A final finish coat was not applied so that the wood trim could be stained to match d cor or overlay frame T
13. ers of the unit as necessary see Figure 29 Oo i c E Z Turn Foot to Adjust Figure 29 3 Check the levelness after each adjustment and repeat the previous steps until the unit is level Go on to 8 Install the Unit Installation Tip If the room floor is higher than the floor in the cut out opening adjust the rear feet to achieve a total unit rear height of 1 8 less than the opening s rear height Shorten the unit height in the front by adjusting the front feet This allows the unit to be gently tipped into the opening Readjust the front feet to level the unit after it is correctly positioned in the opening www U LineService com y UrLINeE 2075WC 2075WCOL Wine Captain che 8C ORPORATION e Install the Unit Anti Tip Bracket Installation 1 Locate two Anti Tip Brackets included inside the unit 2 Place the unit into the area where it will be installed Check the door sides and top for a proper fit Also test to make sure the door opens and closes freely incites Back 3 Remove grill and place a mark on the floor at the front Front of Unit of the unit Also place a mark on the floor in the center gp of the unit See Figure 30 1 90 14 o ots 11 1 16 i 11 1 16 Centerline fi r Marks ge L on Floor Figure 31 5 Place the Anti Tip Brackets on the floor against the line drawn for the outer edge Mark spots for the screw
14. es See Figure 17 2 Visually check for gap between frame and glass If there is an objectionable gap follow steps under Applying Foam Tape to Overlay Frame If there is little or no gap continue to Attaching the Overlay Frame www U LineService com 2075WC 2075WCOL Wine Captain Applying Foam Tape to Overlay Frame If required Inside Edge Incorrect Correct Figure 18 1 Cut foam tape into four pieces two pieces the width of the overlay frame and two pieces the height of the overlay frame 2 Remove the adhesive protection strip from one piece of the foam tape and align to the edge of the overlay frame as shown in Figure 18 adhering the foam tape to the overlay frame 3 Trim each piece of tape immediately after application Do not allow any overlapping of the foam tape Damage to the overlay frame can occur if the foam tape is not trimmed properly Typical Wood T tame E E V 6 X 5 8 Flat Head Screw Two Required Top Pivot Wo equin Plate 8mm Plug Insert Two Required Figure 19 Attaching the Overlay Frame 1 Tap nylon inserts into the top holes drilled in the overlay frame Use two 6 screws to attach top pivot bracket to the overlay frame see Figure 19 2 If auser supplied cabinet handle will be used attach its hardware to the overlay frame at this time IMPORTANT User supplied cabinet handle MUST be counter bored to make sure mounting hardw
15. he trim on the racks may be coated with a final finish or stained 2075WCOL Models are designed for and require installation of an Overlay Frame If none of these treatments are to be included in this installation go on to 5 Adjust Door NCAUTION To prevent permanent damage to the inner liner of the Wine Captain the wine rack wood trim MUST be removed from the unit for staining and or finishing Allow stain finish to dry thoroughly at least 24 hours per coat in accordance with the stain finish manufacturer s instructions prior to re installing the wood trim inside the cabinet of the Wine Captain Failure to do so may cause the inner liner of the unit to have a permanent odor which is not covered by the warranty Adding a Final Finish Coat to Wood Trim 1 Remove each wine rack by sliding it out and up See Figure 12 Slide Out and Up 2 Remove and save screws me securing wood trim to the racks 3 Lightly scruff sand the wood trim with 280 grit 3M Tri M Ite sandpaper 4 Remove sanding dust with a tack cloth Figure 12 5 Apply a thin coat of Minwax Polycrylic following container label for directions Allow to dry 24 hours 6 Lightly sand tack and reapply 2 times if desired 7 Allow the final coat to dry for 24 hours 8 Reinstall wood trim to wine racks using screws removed in Step 2 9 Reinstall wine racks in unit 10 For 2075WC units go on to 5 Adjust Door www U LineServ
16. ice com T UFLINE CORPORATION Staining Wood Trim a Different Color 1 Remove each wine rack by sliding it out and up See Figure 12 2 Remove and save screws securing wood trim to the racks 3 Apply Minwax Water Based Wood Stain to wood with a synthetic foam brush Stain must penetrate approximately 3 minutes After this period while stain is still wet take a stain dampened rag and remove all excess stain Wipe in the direction of the grain with medium pressure to achieve the desired stain color 4 After 2 hours repeat Step 3 5 Allow stain to dry for a minimum of 3 hours before finishing 6 Sand the wood with very fine sandpaper to smooth the surface from the staining process 7 Remove sanding dust with a tack cloth 8 Apply a thin coat of Minwax Polycrylic following container label for directions Allow to dry 24 hours 9 Lightly sand tack and reapply 2 times if desired 10 Allow the final coat to dry for 24 hours 11 Reinstall wood trim to wine racks using screws removed in Step 2 12 Reinstall wine racks in unit 13 For 2075WC units go on to 5 Adjust Door www U LineService com 2075WC 2075WCOL Wine Captain TM Overlay Frame 2075WCOL Units Only Frame Preparation An overlay frame covers the door frame to give a built in appearance Appropriate hardware and a copy of these instructions will be included in the unit IMPORTANT The thickness of the wood overlay frame must be
17. not be possible 3 Prepare Site Your U Line product has been designed for either free standing or built in installation When built in your unit does not require additional air space for top sides or rear However the front grille must NOT be obstructed and clearance is required for electrical connection in the rear Note Unit can NOT be installed behind a closed cabinet door Cut Out Dimensions 1 1 2 24 3 16 Figure 1 Follow the cut out drawing in Figure 1 The 24 3 16 width allows 1 4 for ease in installation and removal of the unit 24 is the counter depth in most installations The unit is 23 1 4 deep including the handle on Black and White 2075WC models 23 1 4 deep including the wood overlay frame on 2075WCOL models and 23 1 4 deep including the door and not the handle on Stainless Steel models see Figure 2 www U LineService com 02 2005 o TM amp Product Dimensions 25 3 8 Including Hand 23 15 16 Black and White e 231 5 16 Stainless Steel 23 1 4 Including Wood Overlay a e 28 15 16 Wood Overlay Figure 2 Please note that the unit has adjustable feet that can add one additional inch to height during leveling or to match adjacent cabinets see Figure 29 on Page 13 02 2005 2075WC 2075WCOL Wine Captain
18. prevent personal injury from sharp edges e Do not lift the unit by the door or door handle Do not install the unit behind closed doors or in any way that would obstruct airflow to the front grille which may cause the unit to malfunction 02 2005 2075WC 2075WCOL Wine Captain T UFLINE CORPORATION 2 Inspect and Plan You have received a carton containing your 2075WC or 2075WCOL Wine Captain with a package inside containing a User Manual a Product Registration Card and an Anti Tip Bracket Installation Kit 2075WCOL units are shipped with a cardboard wrapped door and an additional package of hardware Complete and mail the Product Registration Card or register online at www U LineService com Once your unit is installed keep the User Manual and this Installation Guide in a safe place for future reference 2075WC units are Black White or Stainless Steel Black and White units have a reversible door with a slightly contoured handle across the top Stainless Steel units are covered with a protective coating and have been ordered left or right hand hinged The Stainless doors are not reversible 2075WCOL units are Black with an unattached door that requires the construction of a 3 4 inch thick wood overlay frame You must determine left or right hand opening before construction All units come with maple trim wine racks that can be finished or stained Please carefully follow the directions that apply to your unit
19. s as a guide to lightly punch pilot holes for the 6 x 1 pan head screws See 3 Holding door upright with top of door tilted forward Figure 21 place hole of pivot plate onto bottom hinge screw pin Be sure that bosses on closers align with holes in pivot 5 Attach the door to the overlay frame using the 6 x 1 plate wood screws 4 Tilt top of door into position and install top hinge screw IMPORTANT pin See Figure 22 Tighten only until post is level with top of hinge If you decide to drill pilot holes remove the door and do not use a drill bit larger than 7 64 Do not drill deeper 5 Goon to 5 Adjust Door than 3 8 Door frame and overlay frame must be aligned properly or the door will not operate correctly 02 2005 11 www U LineService com T UFLINE 5 Adjust Door CORPORATION Checking Door Alignment The unit s door is aligned at the factory before shipment However its alignment could have been disturbed during shipment or during overlay frame installation IMPORTANT 2075WC 2075WCOL Wine Captain Properly aligned the door should be 1 8 below the top of the unit s cabinet NOT flush with the top see Figure 23 Compare the top edge of the door to the top edge of the cabinet If the door edge is 1 8 below and parallel to the top of the cabinet go on to 6 Prepare Power Supply If it is not note whether the side opposite the hinge needs to be moved UP or DOWN and u
20. se the following procedure Adjusting Door Alignment 1 With door upside down Remove top hinge screw pin 7 64 Allen wrench or Phillips screwdriver depending on your unit s construction see Figure 24 Remove door by tilting forward and lifting off bottom hinge pin Figure 24 loosen but do not remove the two screws on the door s bottom hinge plate www U LineService com Reinstall the closers lining Mountthe door install top TM Slotted Mounting Holes Angled Edge S CG Towards Center of Door Raise Lower Outside Outside Door Edge Door Edge Figure 25 See Figure 25 If the top far edge of the door needs to move UP move the hinge plate toward the outside of the door and retighten screws If the top far edge of the door needs to move DOWN move the hinge plate toward the inside of the door and retighten screws Mount the door to recheck alignment and repeat Steps 2 and 3 if further adjustment is necessary When top edge of door is parallel to top edge of cabinet remove the door and ensure the two screws are secure Remove the door closers from the bottom hinge clean thoroughly and lubricate the mating surfaces with petroleum jelly up the bosses with holes in hinge and hinge plate see Figure 26 hinge pivot pin and go on to 6 Prepare Power Supply Figure 26 02 2005 2075WC 2075WCOL Wine
21. ter solution Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with clean water Wipe with a soft clean towel to prevent water spotting Stainless Steel Models Stainless steel models can discolor when exposed to chlorine gas pool chemicals salt water or cleaners with bleach Keep your stainless steel unit looking new by cleaning with a good quality all in one stainless steel cleaner polish on a monthly basis For best results use Claire Stainless Steel Polish and Cleaner which can be purchased from U Line Corporation The part number is 173348 Comparable products are acceptable Frequent cleaning will remove surface contamination that could lead to rust Some installations may require cleaning on a weekly basis Do not clean with steel wool pads Do notuse cleaners that are not specifically intended for stainless steel this includes glass tile and counter cleaners e f any surface discolors or rusting appears clean it quickly with Bon Ami or Barkeepers Friend Cleanser and a non abrasive cloth Always clean in the direction of the grain Always finish this process with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems Use of abrasive pads such as Scotchbrite will cause the graining in the stainless to become blurred Rustthat is allowed to linger can penetrate into the surface of the stainless steel and complete removal of the rust may
22. y UFLINE C OR PORATION Echelou Sertes Installation Guide ae 2075WC Wine Captain and 2075WCOL Wine Captain with Overlay www U LineService com Phone 414 354 0300 FAX 414 354 7905 Service amp Parts Tech Lines Phone 800 779 2547 FAX 414 354 5696 OnlineService U Line com 2005 U Line Corporation 02 2005 T U LITE 8C ORPORATION Contents Exterior Cleaning llle 4 Cut Out Dimensions 00 eee eee 4 Product Dimensions 00000 cece eee eee 5 Door Swing Clearances Information 5 Reversing the Door 0000 cece eee eae 5 Other Site Requirements 20000 6 Side By Side Installation Instructions 7 Adding a Final Finish Coat to Wood Trim 7 Staining Wood Trim a Different Color 8 Overlay Frame 12 Gig Sound Soa Bone bares 8 Checking Door Alignment 12 Adjusting Door Alignment sssslsss 12 Electrical Specifications 0 0 0 cece eee ee 13 Leveling Information 00 cece eee nes 13 Installation Tip 00 0 e eee eee eee 13 Anti Tip Bracket Installation 04 14 Installation Troubleshooting 2 20 15 Initial Start Up 0 0 0000s 15 Start Up Troubleshooting 0 220000 15 Service Information 020000 eee ee eee 16 www U LineService com 2075WC 2075WCOL Wine Capt
Download Pdf Manuals
Related Search