"user manual"
Contents
1. 1 Download the operation system update programs to the desktop of your personal computer 2 Connect Star pro with PC as per the connecting method we introduced in section 10 2 1 and enter USB update mode 3 Executing the update programs which you just download form AUTOBOSS 53 PDF NAWA pdfFactory Pro PIR Get www fineprint cn ADTO3O055 User manual website and saved on the desktop Click the installation by the hints on the screen until you finished the whole operation See the left diagram 4 Safely remove the USB device and disconnect the USB cable restart the unit to finish the upgrading Note Make sure you removed the USB device If you forgot this step may lead the update failed and you should redo every step 10 2 5 BIOS Update 1 Download BIOS update program from AUTOBOSS website to the desktop of your personal computer 2 Restart the main unit and click the box in the middle by the hints on the main unit with touch pen The System can update the BIOS automatically 3 After the BIOS upgrading you must upgrade the OS as per the instruction in section 10 2 4 or the unit can not work Note 1 Before you upgrading the BIOS please check is the BIOS version of the Star pro is lower than the one on AUTOBOSS website Or you need not to upgrade it 2 We suggest to use UPS to protect the stable voltage during upgrading the BIOS because the power cut off during upgrading the BOIS will damage2. Chapter8 Digital Multimeter 8 1 Introduction The Digital Multimeter DMM is a powerful diagnostic tool that allows you to determine specific values of different measurement modes The DMM modes include DC and AC voltage resistance continuity and diode check The DMM s large display makes it ideal for measuring a variety of general signals as well as automotive signals 8 2 Testing Procedures The testing procedures of the digital multimeter is as following 1 Connecting the main unit to the converter through the main test cable 2 Supply 12V power through battery cable Perform zero calibration Connect the test leads GARE ees Choose component of testing 6 Save and print 8 2 1 Zero Calibration For an operation of zero calibration see 9 3 1 8 2 2 Cable Connection Cable Connection 1 Connect the red test cable to the port CH1 on the converter Then connect the other side of the red test cable to the test point Connect the ground wire to the port of the converter on one side and mount the end to the negative side of the battery or to the chassis ground Note Do not plug or insert main cable Remark Cable connection 1 only for when the scanner is powered current voltage resistance duty on cycle and frequency modes 46 PDF 4E pdfFactory Pro TAUHABORGUEE www fineprint cn User manual Cable Connection 2 Connect the sync cable to the port CH1 on the converter Then connect t
3. communication between the main unit and the converter is good 5 2 2 Test lead connections Connect the test point to CHA CHB CHC and CHD by the red yellow blue and green cables You can choice connect how many and which channel by necessary Connect the ground wire to the port of the converter on one side and mount the end to the negative side of the battery or to the chassis ground Ensure all cables and test leads are clear from any rotating parts such as fan Then turn 32 PDF 4E pdfFactory Pro TiAUHABOAGUEE www fineprint cn ADTO3O055 User manual on the main unit and start the engine to begin testing 5 2 3 Channel controls The Osciloscope has four separate channels that can display data simultaneously 1 Channel setting The channel buttons are located in bottom left corner of the touch screen display Touching a channel button gives you access to the settings specific to that individual channel A IL fun en D D D dr T a og og i og o g ot 1 136 Tux Ines Dar mE rose La m r OF o uei v kg Uti Hh zx nu ela Click Run or Stop to turn the channel on or off 1 Offset Adjusting the offset changes the vertical position of an individual signal on the touch screen display 2 AC DC coupling oelecting the correct type of the coupling mode for your signal is important for accurate testing AC coupling The mode displays only the AC compon
4. mode Data record m Jose Diagnosis Engine Analyzer T EN vehicle system circuit diagrams Information Dictionary English Chinese dictionary Keyboard Numeric inputs Keyboard Shit au Chinese English keypad Main keys Help Help information for operation BACK Back to previous interface Page Up Page Down Left UD kel ed Right buttons 10 PDF 4E pdfFactory Pro wea est www fineprint cn ADTO3O055 Du LI Hama PF h H V Ae Kr dalih Cee fas CMA me Fas L lg ee IW Fe e J 1 J I L ef sl 1 Li S cde th sles c dk l L r z u 1 1 Bo Ir 2 E i EE di r d KN Aa SES ERE te i i TE i duy rz irit rigimm BLip lag Tis En vun FRI In zck Jee AU SS User manual 2 2 Settings The settings menu includes User Information Language Display Touch Set Enter projection USB update System check 2 2 1 User Information Click User Information under the Settings menu and the screen will be shown as in Figure Type in the name phone number fax and address and then save it This information will be shown in the printout during paper printing The information can be input through the keyboard by selecting the keyboard icon under Keyboard menu f incorrect information is entered just click to delete it If you want to enter Chinese characters please press the button first as shown Press EI to save
5. product Star Pro Designed for professional automotive technicians Star Pro utilizes a real time operating system with a number of diagnostic instruments supported to solve the sophisticated electrical and mechanical systems on today s modern vehicles such as testing vehicle sensors ECU input output ignition and analyzing vehicle signals etc Features of Star Pro Four groups signal collected simultaneously for convenient comparison Select ignition types directly during the testing Compare the voltage between power spark and waste spark for DIS system Can test integrated distributor ignition system Self learn of standard waveform function supported providing convenient diagnosis Common values preset function supported for quick testing Save printout and replay the testing results in static and dynamic mode Colorful LCD display for visual operation 1 2 Star Pro Main Unit Configuration Dimension 347MM L x181MM W x41MM H PDF EH pdfFactory Pro wheat www fineprint cn ADTO3O055 Operating Mode LCD Memory CF card Glitch capture Bandwidth Power supply Communication Measuring channels A D converter Memory depth Glitch capture EEPROM Sync dynamic memory User manual LCD Touch Screen High Resolution 6 4 640 480 CCFL Backlight FLASH 2MB RAM 8MB 256 M 400 ns 500 KHz AC DC cigarette lighter battery USB 12Mbps Internet Interface
6. 1 us NA El EN We Cursors IF Ika Hii ship Loo 518 Le d You can enable two horizontal and two vertical cursors to make precise measurements of waveforms display on the grid You can turn the cursors on and J arane irria T5 Tag A Mun SN Horizontal cursor You can press H CSR button to choose H1 H2 and Cancel all cursor Then press H1 or H2 to active cursors or press Cancel T all cursor button to cancel all cursors ZS SES You can move the cursor by using and buttons far1l rll arzrr D d Wis lur IC Vertical cursor you can press V CSR button to choose V1 V2 and Cancel Diddi Dig To Fug7 lt m all cursor Then press V1 or V2 to active cursors or press Cancel all r 19 cursor button to cancel all cursors You iB rU e can move the cursor by using 1 and D d Wis lur IC buttons Ri d T 3 IH 1 Zap L Lia 36 PDF cee EAI pdfFactory Pro TiAABOAGUEE www fineprint cn User manual 4 Parameters It can display the signal characteristics that you are testing rsch LS ELLE Ei ir iF Tu 3 ia o iaer Ede 1 1 i i 1 1 1 Wer rose Foly AE ar Fic urs af T or 5 Save and print a Click Freeze and the following screen should be shown as in Figure Users can print save or replay the current displayed waveform or pictures recorded from Capture function When finished select RUN t
7. 10Mbps 4 independent A Ds oscilloscope channel 1 primary ignition channel 2 secondary ignition channel 1 sync signal input channel 12 digitals 6M EEPROM 8M SDRAM 8M 1 3 Technical parameter DC Voltage 9 16V 2A AC Voltage 220V 50Hz Ambient 50C 400C Humidity Lower than 85 Storage 20 C 60 C 20 C less than 48h 60 C less than 168h PDF cee ERI pdfFactory Pro iwWHIWRA GME www fineprint cn tte paper cutpir web cable pert LCD GILA Perce MI Akan Dern Ei M n SES Enai c Analyzzr uyl Ful User manual 1 4 Star Pro Profile 1 4 1 Main unit structure The structure of the main unit as shown in left picture D Printer 2 Main unit 3 Rubber handle Galic in rirtzr L 4 I d l A e PDF SEH pdfFactory Pro whHheAS GIS www fineprint cn ADTO3O055 User manual 1 5 Star Pro Unit packing list en Number BDes pion ty Main Unit CF Card 30AD011A 30AC134A CF Memory card Nissan 14 30AC133A Audi 4 30AC132A Benz 4 30AC104A OBD 16 30AC130A Honda 3 Diagnostic connector 30AC129A MIT 12 16 30AC128A Toyota 22 30AC127A Toyota 17 30AC113A BMW 20 30AC125A Benz 38 22 Test leads 31AC035A Sync Probe 1 31AC023A Secondary Test Group Lead Black 31AC022A Secondary Test Group Lead Read 4 n2 NO NO NO n2 NO n2 co Co N O O1 A Co CO PDF cee ERI pdfFactory
8. Cable EE tf 46 8 2 3 Choose component of testing saananing a naning a aa aing a 47 chapters Vereen 48 GN e WE Le e e 48 9 2 Date and Ime m mmm nmm memet nnne anana niri reser ern nnns 48 SG AM QUO E 49 GC NS e e fe e e EE 49 9 3 2 Gain calibration ccccceccececcecccceccececcecccucueceeeeceuaecuccecaueeeaecsunecsuneceeass 49 9 3 3 Save as default 2 0 cccccccceccececceccceccececcececcuccececceceeaecueeecaeceuaecsuaecueneeenass 49 b PDF XAFI pdfFactory Pro TiAXABOAGUEE ww fineprint cn ADTO3O055 User manual 9 3 4 Use default sess mmm meme nemen nemen nere se nire rens 50 9 4 Basic lu reit HE de BE 50 9 5 IS SF UTE e Bem 50 SEET 51 Chapter 10 tee Ce te EE EE 52 DOW Te 52 FeO AS STEDS MORIR TR RR 52 RN See 52 10 2 2 Update program downloading instruction 53 10 2 3 Diagnostic program update 53 03245538 AN aana enang na dan aa Kn WONGE GN ENE BANGO RA AB PE EA RI an BI Ka na Gak aia gana 53 1025 TO EA warana aga a aa Da Da a a dan a Gen aa Kia a ng a GE IA E I LI A 54 Chapter 11 TON EE IT ENEE EEN 55 PEFEA CUMING Te SUING RE 55 TEZ OPa ein Be B Lot del Em 55 Appendix 1 Secondary ignition patterns Power and waster iii 57 Appendix 2 General Scope Eed 58 C PDF SCE ERI pdfFactory Pro iMAC Mt www fineprint cn ALTOTOSS5 User manual Chapter 1 Introduction to Star Pro 1 1 Introduction Welcome to use AUTOBOSS powerful
9. KV dwell time burnt time power waste ratio etc 3 2 Testing procedures The followings illustrates the testing procedures of viewing secondary ignition signals 1 Connecting the main unit to the converter through the main test cable 2 Supply 12V power through battery cable Perform zero calibration Connect the test leads Select either Ignition Model Select or Vehicle Manufacturer 6 Adjustment and setting 7 Save or print 3 2 1 Zero Calibration Zero calibration is to verify the data communication between the main unit and the converter is good 3 2 2 Test leads connections Take a 4 cylinder engine with firing order 1 3 4 2 as an example the test procedure of Star Pro is illustrated as follows PDF FEH pdfFactory Pro AMARA www fineprint cn PDF MAHA pdfFactory Pro ADTO3O055 Caution Do not attach or remove the leads from the coil wire when the power of the main unit is ON 7 iride a T ene ga t Caution Do not mount or remove the test leads from the coil wire while the power of the main unit is ON User manual 1 Distributor Ignition 1 Connect the BNC side of the Sync probe to the SYNC port Mount the other end of the sync probe to the coil wire of cylinder 1 2 Connect the BNC side of the secondary test lead to the SEC IGN port of the converter Mount the other side of the secondary probe to the high tension coil wire of the ignition system 3 Connect th
10. Pro iwWHIWeA est www fineprint cn EE manual TE EJ ES ES ES E ES E E E E E E ES E IE Documents EJ Note This Packing list is only for your reference Please get the Standard configuration from the packing list in the product PDF NAWA pdfFactory Pro JAWARASONGEE www fineprint cn User manual 1 6 Introduction of converter The signal is adjusted and sent to the main unit by the converter Please see the left picture It is a standard converter 1 A CH1 Port CH1 is the default trigger channel for 4 Channel Oscilloscope comparing the relevant waveform CH1 can also be used for Digital Multimeter DMM 2 B C D CH2 CH3 CH4 Used for 4 Channel Oscilloscope testing Analyze and compare the waveform by selecting relative channel from CH2 to CHA The function of General Oscilloscope DSO Special Oscilloscope Auto DSO Digital Multimeter will be supported if Port A B C D are connected with the red yellow blue and green test lead by order 3 E COM Used for connecting the converter and main cable And transfer the adjusted signal to communication module 4 F SEC IGN Port F is used for the secondary ignition testing connecting to black probe 5 G SEC IGN Port G is used for secondary ignition testing connecting to the red probe Note Port F and G are connected to the red black probe respectively for DI and El 6 H SYNC Port H is connected to
11. cn User manual HW IRIS Pi D of A ms epp RES Go to www autoboss net and select Download we fet sina dw upra See di enika 0 m Pw p Sa mago SEW IND eng ME el Se e ri LUCENE T ONE OD m Elei ocu d wll After entered download center click the Download icon of Star Education Demo to download the demo program to your personal computer mm omm ice teg nmm PER Ass c rrj d Piet e pire e MERA r sst Hia G HEA 1 15 TECE 1 18 7 inh Parah er ery Ca ae Cae Wa ERE Da Double Click the educatedemo exe and program icon of install the 13 PDF HEH pdfFactory Pro wAHAeA es www fineprint cn ALTOTOS5 User manual Click install to start the software installation zm adig G gi rig ks e TOUT pnm Click the icon PowerPoint Micro as shown in left picture to enter education projection mode After click the icon the left side interface will on your personal computer Canter Ke Bar Pn 7 TREPA Pon e 2 Connection Star Pro to PC Connect Network Cable to PC and Star Pro One port is connected to the Star Pro and the other port is connected to PC 14 PDF SEH pdfFactory Pro 9HIWAS GIS www fineprint cn ADTO3O055 User manual 3 Demo Follow the instruction bellow step by step Click the button enter projection under the menu of System Setting Click the button save screen on PC monitor Click the icon on the left corner of the St
12. keyboard Click Enter to adah E save the settings 48 PDF FEH pdfFactory Pro DIAS Get Www fineprint cn ADTU3SO0S5 User manual 9 3 Calibration On calibration interface the user can calibrate the zero point and gain also the user can save the setting as default or use the default settings 9 3 1 Zero calibration The sampling of AD range is from O to x NN ER 4095 and the relevant voltage range is from 1V to 1V So generally the zero point is 2048 Once the zero point excursions from the 2048 the user should adjust it by zero calibration Operation steps Connect the analyzer with converter and disconnect all of the test leads Enter zero calibration interface 2 Input the 6 bit codes 888888 to enter the calibration Click the button ok for several times as per the hint above ok button During the calibration please observe if the values are beside 2048 Normally the values are 2048 200 or larger 8 After finished all the procedures click the button Exit to return to calibration interface 9 3 2 Gain calibration The system need gain calibration after complete the zero calibration Normally the AD value is 1 000 Please calibrate the gain value via this function to ensure the accurate Note AUTOBOSS had done the gain calibration before package So once the value is not accurate please contact AUTOBOSS service center or our distributor for help The users can not calibra
13. the main unit 54 PDF cee EAI pdfFactory Pro iwWHIWeA Gt www fineprint cn ADTO3O0S5 User Maunal Chapter 11 Troubleshooting 11 1 FAQ during testing 1 Why the main unit CF card and converter can not change with user s mind Answer Because every set of main unit CF card and converter box is unique Only the ones in the same set can do A D convert correctly Or the fault by A D convert will lead the signal inaccurate 2 why the SYNC signal do not stable during pri ignition Answer Normally we use the cylinder 1 as trigger cylinder during pri Ignition testing o0 one side of the SYNC probe is clamed on the cylinder distributor cable of cylinder 1 If cylinder 1 did not work very well can infect the whole test There are three method to resolve this problem change another trigger cylinder change the clamp direction of the CYNC probe Hedo the zero calibration 2 OOO Why the waveform do not stable or no wave form during Pri or Sec Ignition testing Answer During the ignition testing please pay attention to the following items D Select correct ignition order 2 change the current direction of the cylinder 3 Make sure the Sec ignition probes which are free do not short to ground 4 channel style 4 Why we must do the zero calibration before test Answer The sample AD got is range from 0 to 4095 and its voltage is range from 1V to 1V so normally the zero point is 2048 In the actual operation th
14. to information 2 2 2 Language oelect Language under Settings menu NOTE Star pro has already set English as the default language Press language gt Xx to switch into Chinese PDF 4E pdfFactory Pro wea est www fineprint cn ADTO3O055 User manual 2 2 3 Display oelect Settings from the main menu and then select Display the Fig 2 7 page will pop out Adjust the optimum contrast with the touch pen and choose black white or colour the system will save the adjustment and return to the main menu automatically 2 2 4 Calibration There are two methods on making calibration in order to keep accuracy of the LCD screen SUC IM lean erts cress Method 1 Turn on the power and touch the LCD screen for more than 2 seconds with the touch pen to access the page shown on the left Method 2 Click the button Touch set under the menu of Information The User must click the center of the cross according to the information displayed on the LCD screen to make calibration The machine will keep the setting for next operation 2 2 5 Demo leagh ay car ol Ue crass Demo is a projection function which is very popular in Training X school university or garage due to the convenience unnecessary connecting to the car Software download and installation Please Login AUTOBOSS website www autoboss net to download the projection software 12 PDF x4 pdfFactory Pro wHIWeA Gt www fineprint
15. valve position EVP Vehicle speed sensor Analog Vehicle speed sensor Digital ECT MAF Analog MAF Digital Low frequency MAF Digital high frequency Wheel speed WSS Knock sensor IAT CKP sensor Hall CKP sensor Magnetic CMP sensor Hall 39 PDF NAWA pdfFactory Pro PIR AOISE www fineprint cn ALTOTOSS5 User manual CMP sensor Magnetic BARO Analog BARO Digital CAN BUS EGR Idle air control IAC Idle speed control ISC Air bypass TAB Shift solenoid valve Air diverter TAD Actuators Canister purge CANP Increase to press ABS solenoid valve Mix with adjustment control Hydraulic pneumatic control in gearbox valve Gearbox lock computer valve Negative control Common Fuel injectors Peak s hold 40 PDF NAWA pdfFactory Pro iWHIWRA Gt www fineprint cn ADTO3O055 User manual Primary secondary Ignition system Sync probe secondary Sync Primary Sync Hall effect P U Magnetic P U Distributor Spark timing Optical P U Charger Battery voltage Electrical Ground Alternator ripple Fuel pump Primary ignition Current waveforms Low current probe High current probe PDF cee EAI pdfFactory Pro iWHIWRA Gt www fineprint cn ADTO3O055 User manual AC vacuum DC vacuum Vacuum AC DC vacuum Sync AC vacuum Sync Pressure Pressure Pressure Sync Other settings Same as the settings o
16. DSO The 4 channel oscilloscope allows you to view multiple signals simultaneously PDF 4E pdfFactory Pro wWHIWeA Get www fineprint cn ADTO3O055 User manual The User can modify the parameters of the oscilloscope and perform testing on different vehicles 4 Auto DSO The 4 channel DSO allows users to view multiple signals specific to automotive applications simultaneously opecial oscilloscope is used by someone who is not familiar with the automotive technology 5 Engine analyzer The main function of the engine analyzer is to diagnose the starting charging systems of the vehicle the sealing ability of the cylinder etc DMM The DMM includes the following items DC voltage AC voltage DC current DC Low Current DC High Current Frequency Duty Cycle RPM Resistance Pulse Width Note The functions of Star Pro will be explained in detail in the subsequent chapters PDF cee EAI pdfFactory Pro iwWHIWeA Gt www fineprint cn ADTO3O055 User manual Chapter 3 Secondary Ignition 3 1 Introduction 1 Testable ignition types Distributor with high tension wire Distributor without high tension wire Electronic power and waste Coil Near Plug CNP and Coil On Plug COP ignition systems 2 Waveform Display Mode There are following display mode Single Cylinder Parade Raster 3 Dimension Superimposed Bar chart etc Different display modes reflect ignition voltage firing voltage
17. SYNC probe Its function is identify ignition trigger signal and used as Multimeter to test RPM Also it will synchronize the signal during the primary ignition and secondary ignition DSO Auto DSO test PDF MATAH pdfFactory Pro wh AWA GE www fineprint cn ADTUSO0S5 User manual 7 CPRI IGN Port is connected to the primary pickup connector leads for primary ignition test This function also can display the signal output on the primary test interface 8JC c Connected to ground and provides signal reference interface for 4 channel oscilloscope Also it provides positive reference interface for DMM test Note J port connected to ground cable of oscilloscope and the other side of the accessory connected to vehicle ground or negative pole of vehicle battery is used for providing the waveform and current reference interface during test 9 K CURRENT Connected to the negative pole of the current clamp and is used for current measurement 10 L CCURRENT A Connected to the positive pole of the current clamp and is used for current measurement Note K Lis connected to the small current clamp or large current clamp for amperage measurement PDF NAWA pdfFactory Pro TAHABOANGUEE www fineprint cn ADTO3O055 User manual Chapter 2 Operation Instruction 2 1 Start 2 1 1 CF card installation While the main unit is off insert CF card with the labeled size on the top into CF card slot on the main u
18. Star Pro Engine Analyzer part User manual Version 1 0 Copyright 2006 by AUTO3OSS Tech Inc PDF cee EAI pdfFactory Pro iWHIWeA Gt www fineprint cn ADTO3O055 User manual Disclaimer All rights reserved no part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any methods electronic photocopying recording or otherwise without prior written permission of AUTOBOSS Neither AUTOBOSS nor its affiliates shall be liable to the buyer of this product or third parties as a result of accident misuse alteration or abuse of this product or failure to follow the written instructions from the manual Since different vehicles and their systems may behave differently under different operating conditions and environment AUTOBOSS cannot guarantee its product will work correctly with every system in every vehicle By using AUTOBOSS products you are aware of the fact that its software and hardware may contain errors or bugs and thus provided AS IS We will make our best effort to correct errors and any bugs in our software and hardware but we specifically disclaim any liability for damage to your computer or to your vehicle and we do not promise to have any particular improvements or software updates on any specific date otar Pro is designed for sole purpose of diagnosing and repairing automotive electronic systems Only trained service personnel can operate it Neither AU
19. TOBOSS nor its affiliates shall be liable to the buyer of this product or third parties as a result of accident misuse alteration or abuse of this product or failure to follow the written instructions from the manual Every attempt has been made to provide complete and accurate technical information based on factory service information available at the time of publication However the right is reserved to make changes at any time without notice For any question please contact AUTOBOSS by following ways 1 Visit AUTOBOSS website at http www autoboss net 2 Send mail to AUTOBOSS Tech Inc customer service center at the following mail address 5 F East Bldg 304 Shangbu Industrial Park Zhenxing Road Futian Shenzhen 518028 China Send email to marketing autoboss net 4 Call AUTOBOSS office at 86 755 8328 5146 86 755 8328 5370 or call your local distributors e Trademark The trademarks logos and service marks Marks displayed in this document are the property of AUTOBOSS or other third parties Users are not permitted to use these Marks without prior written consent of AUTOBOSS or such third party which may own the Mark AUTOBOSS is a registered trademark of AUTOBOSS TECH INC Copyright 2006 by AUTO3SOSS e Us PDF FEH pdfFactory Pro DIAS Get Www fineprint cn ADTO3O055 User manual User Manual instruction This equipment must only be used by trained professionals lt y Before using Star Pro please
20. ar Pro The information of Star Pro will be displayed on the PC screen Note The screen displayed on PC will be a little bit slower than Star Pro Click the button to fresh the PC display each time 4 Capture Click the button save screen on PC monitor to save the information The information will be saved in the educatememo folder The User can make lessons with these pictures 15 PDF NAWA pdfFactory Pro TiAXABOAKGUEE www fineprint cn ALTOTOSS User manual 2 3 Introduction of Engine Analyzer Z rr 1r dr ge fh JA In the main menu select Analyzer under Diagnostic menu and the following screen will be shown as in Figure I TTul tira Ar al mm Star Pro includes six different functions Primary ignition Secondary ignition Digital Storage Oscilloscope DSO Auto Digital Oscilloscope Auto DSO Engine Analyzer Digital Multi meter DMM The followings illustrates the features of each functions 1 Secondary ignition The following ignition systems can be tested with Star Pro Conventional ignition external coil wire Conventional ignition Internal coil wire Direct Ignition System Distributor less Coil Near Plug Ignition CNP Coil On Plug Ignition COP 2 Primary ignition The following ignition systems can be tested with Star Pro Distributor Ignition External Coil Distributor Ignition Internal Coil Coil On Plug Ignition COP 3 Digital Storage Oscilloscope
21. e Select Click on Ignition Mode Select Then Select the followings DI with coil wire DI without coil wire Coil On Plug COP Coil Near Plug CNP Power amp waste firing SE Then select No of cylinders 2 3 4 5 6 I 8 10 12 manei dE UP EHE Cl slih zall Ges Ir1z d Jane Tel ele F slay 21 PDF cee EAI pdfFactory Pro wHIWeA et www fineprint cn User manual Then select the firing order to enter the Sec Ignition testing interface 2 Vehicle Manufacturer Select the region of manufacturer Asia car includes vehicle makes from Japan Korea and Southeast Asia Europe America cars include vehicle makes from Europe and America China car includes all makes from China Select Vehicle make Select No of cylinders 2 3 4 5 6 8 10 and 12 22 PDF IEH pdfFactory Pro iH AAG www fineprint cn User manual Select Motor type by matching the 7 digit of the VIN and then enter Secondary ignition waveform pattern 3 Last test record Select the makes and models that have been previously tested 23 PDF cee Ha pdfFactory Pro DA GI www fineprint cn User manual 3 2 4 Connecting the leads kees It is very important to mount the leads lovanna correctly into the coils in order to view the necessary waveform This manual will illustrate the ignition waveform of 4 cylinder waste and power ignition system with a firing order of 1 3 4 2 the po
22. e ground wire to the port of the converter on one side and mount the end to the negative side of the battery or to the chassis ground 4 Ensure all cables and test leads are clear from any rotating parts such as fan Then turn on the main unit and start the engine to begin testing 2 Direct ignition system 1 Connect the BNC side of the SYNC probe to the SYNC port of the converter Mount the other end of the SYNC probe to the coil wire of cylinder 1 If the car does not have distributor lead take out whatever cylinder s ignition coil take cylinder 1 as example Connect the trigger cylinder and spark plug with a connecting cable and clamp one side of the SYNC probe to the connecting cable 2 Connect the BNC on Sec Ignition probe with SEC IGN on the converter Another side of the Sec Ignition probe connects to the cylinder distributor lead or connecting cable with in testing 3 Connect one side of the ground cable to on the converter box another side to negative pole of the battery or ground cable on the vehicle Note Make sure all cables or leads area way from the rotating parts of the vehicle 4 Start the engine and begin testing SCH RAGE www fineprint cn ADTO3O055 Caution Do not mount or remove the test leads from the coil wire while the power of the main unit is ON 20 User manual 3 Power waster ignition system Ignition order 1 3 4 2 The cylinder to ignition coil posi
23. e zero point will departure from 2048 this problem can be solved by zero calibration Zero calibration ensures the test accurate 5 The waveform does not stable during the DSO Auto DSO test What can we do Answer Users can click trigger to set the Trigger posi Trigger mode Trigger edge Trigger source setup 6 We remove the main cable when the unit is on then turn on the unit but the unit no response Answer Possible reason battery clamps burned Please change the battery clamp The users must pay attention that the main cable can not be removed when the unit is on 11 2 Operation question 1 The screen has a cross the stays when turned on the unit Answer one possible reason is you have entered the screen calibration mode Please 55 PDF 4E pdfFactory Pro PIR AOISE www fineprint cn ADTO3O0S5 User Maunal click the cross center as per the hints on the screen After the calibration you can get the main interface The other possible reason is the screen is blocked Please contact AUTOBOSS customer service center to solve 2 The screen displayed CF card read failed when the unit turned on Answer Possible reason D The CF card is not in the Star Pro Turn off the unit and insert the CF card 2 CF loose Turn off the unit and unplug the CF card then insert the CF card After all the steps then turn on the unit 3 CF card damaged Please change the CF card CF card format incorrect Please reformat the CF ca
24. ent of the signal under examination DC coupling The mode displays both AC and DC components of the signal his is the default setting for four channels Ground coupling The mode ties the internal A D input to ground 33 PDF 4E pdfFactory Pro wWHIWeA Get www fineprint cn User manual 2 Trigger setup The Star Pro has a set of the trigger controls that determine the exact instant the trace begins the sweep across the Screen If a trigger is set at a specific voltage level and the signal being sampled achieves that trigger level voltage then the Star Pro displays the signal Trigger source Trigger source allows you to choose from a wide variety of sources CH1 CH2 CH3 CH4 Trigger mode There are four different trigger modes to choose from when viewing a signal Normal Auto Single Shot and Free Run Normal trigger Normal trigger is a common trigger mode and requires that you know the characteristics of the signal you are trying to display Auto trigger Auto trigger is the easiest mode of trigger to use when viewing an automotive signal The Star Pro displays a signal that meets the trigger level at the trigger position If the signal does not meet the trigger level condition Star Pro automatically displays any signal that is received Single Shot trigger Single shot trigger is used when you want to capture a certain characteristic of a know signal 34 PDF 4E pdfFactory Pro wea est ww
25. f general oscilloscope DSO 42 PDF cee EAI pdfFactory Pro iwWHIWeA Gt www fineprint cn ADTO3O055 Chapter 7 Caution Do not attach or remove any test leads from the coil wire when the power of the main unit is ON 43 User manual Engine Analyzer 7 1 Introduction Engine analyzer includes Charger test and Starter test Charger test It can test the charger by the waveform of the voltage and current when the charger working Starter test It can test the starter by the waveform of the voltage and current when the starter working 7 2 Testing procedures 1 Connecting the main unit to the converter through the main test cable 2 Supply 12V power through battery cable 3 Perform zero calibration 4 Connect the test leads 5 Adjustment and setting 6 Save and print 7 2 1 Zero calibration Zero calibration is to verify the data communication between the main unit and the converter is good For an operation of zero calibration see 9 3 1 7 2 2 Test lead connections Charger test Connect the current clamp to the charger positive cable and connect the other side of current clamp to the CURRENT PDF cee ERI pdfFactory Pro wea est www fineprint cn ADTO3O055 Caution Do not attach or remove the test leads from the connections when the power of the main unit is ON IElaza Det ley ed Lo Ce 1 zcn 1 7 qn Vjm7a Dae Fan 44 User manual and CURRENT port of the con
26. g standard waveform and malfunction waveform 3 Inquiry by Car User 51 PDF NAWA pdfFactory Pro iwHIWRA Gt www fineprint cn ADTO3O055 User manual Chapter 10 Software Update 10 1 Note Please read the following instructions before operating the update 1 Make sure the CF card is in the CF card socket of Star Pro main unit 2 Make sure the power is stable and all cables are well connected when you are ready to upgrade the software We suggest to use UPS to protect the CF card during upgrading because the CF 1 12V Adaptor 2 Power port card may damaged if the power cut off or 3 USB port for Main unit the cable disconnected 4 USB Port for PC 3 Please do not do any other operation on computer or Star pro during the CF card upgrading 10 2 Update steps 10 2 1 Preparation 1 Personal computer with windows 2000 or windows XP operation system And the computer must connect to internet If your computer is Windows 98 you should download and setup USB driver too 2 Connecting Star pro main unit and personal computer with the USB cable in the package 3 Connect the Star pro main unit and power with the 12V adaptor Make sure all cables are correctly connected See the left picture 4 Power on Star pro main unit Click the USB icon on right up position of the main unit or select USB mode under System settings on the main interface to enter USB update mode See the left picture No
27. grams onto the CF card NOTE When CF card is damaged or cannot be read format CF card to FAT32 format first and then continue installing the diagnostic programs PDF 4E pdfFactory Pro wea est www fineprint cn ADTO3O055 User manual Table of Contents Aas NA a a E EE IER CNS E KANG EON naa aaa an naa AA NA na EE EE iii Operat on DEE aut O NS EE EE E EE iii Chapter 1 Introduction to Stars PIO ara nadae aana a E E E 1 1 1 Innere Tier e a VE 1 1 2 Star Pro Main Unit Configuration ssaaa eee eaaa e eaaa anana nana a nana eaaa anane eee 1 1 3 Technical parameter EE 2 UE We Ee WE E 3 UE MUST IPE SAJA Tani ag Sa ngae apaa aab aana mM 3 Ee asana ela kajata ag ela a ee ets ale ada a a eg a a a a anaa aa Kena aa a aga aaa a a a AE EN AT e aa aa a aa aa aja aaa ala aa aaa 3 15 Star Pro Unit PACKING ISt asana toto gan aaa ara aga ng TEH NAN EH aan Da a 4 1 6 Introduction OF CONVENT aa aa aa aa e Ka as KASAN A add da dd td adt Na AA BADA NA 6 a a KNA a MA BAN EE Na ET a EEN 8 PAE E i EE 8 2 1 1 CF card instalation EE 8 212 ee UE 8 Ce DEE d rale MAN AN A NA A ee ee ee 9 214 Man menu TL ONG TUDII as aka aa aa asa a A aaa ata a a a aa a APAK AA a a tud AA A MU a Na 10 ge EE 11 2 2 1 User Information WE 11 PAPARE ee 11 e a Re EE 12 2 2 QUO OM e 12 D TON SG O E 12 2 9 Reie eial lege or e Lef 16 Chapbene3 Secondary oni eh on ee 18 Zielt ele el e BEE 18 Se Le el elle EN 18 EES 18 3 2 2 Test leads connection
28. gs eaaa eea eaaa NAN a KAN N NAN N aane a nennen 18 9 23 pije SEC ICI ee 21 GE Meute UNG NE ledd 24 PDF SAFE pdfFactory Pro TiAXABOAGUEE ww fineprint cn ADTO3O055 User manual Chapbenod BEE ege 2 a A argo E e La pm 27 S za usgeliet oli E 27 4 2 1 Zero calibration cesses mmm nemen nnne mereri rennes 27 4 2 2 Test leads connechon aee eee awae eaaa eaaa mmm nnns 27 4 2 3 Vehicle Contguratpon AEN 29 Chapter 5 General Oscilloscope DSO oco on EE ENEE 32 Edi el leie EE 32 5 2 1 Zero calibration EE 32 5 2 2 Test lead connections 0 2 cccccececcececcececcccececcccecececaucsccenecsccuaetseauneneneunenes 32 5 23 Channel COD Os eebe 33 Chapter 6 Automotive Oscilloscope Auto DSO aaa ag 38 6 2 TES DIDOL SOU OS Rm 38 oe T zen Call ball 38 6 2 2 Test lead connections cccccecececcecececcececccececucecseunecseeuecseaunerseeunenes 38 6 2 3 Choose component of testing sasada kaag aa kaag aa A aa ag aaa WA a kaa ana WA Ga gawa 39 Blau BIV Anal yai aa aa aka naturae EE EE 43 7 2 Testing procedures nennen nnn nnna nnns nean nnns nans 43 7 2 1 Zero calibration EE 43 7 2 2 lest lead connections ccceccecececcececccecececcececucecscuuecsucunecstaunenanaunenas 43 Z2 o AdU men ale S G EE 44 AGENCE naa E U 16 0 1 NONG NGA EE 46 8 2 Testing Bd tele 46 8 2 1 Zero Calibration c cccccccceccecccceccececcecccececuccececaecuccececeuaecsuaecuesececass 46 8 2 2
29. he sync probe to the high tension wire Connect the ground wire to the port of the converter on one side and mount the end to the negative side of the battery or to the chassis ground Remark Cable connection 2 only for Note Do not plug or insert main cable PM mode when the scanner is powered on n d 8 2 3 Choose component of testing CA YA sah The component include DC AC Large SCC current Small current FREQ RES DEE i Fluctuation Air ratio PRM Temperature Pressure Vacuum sam ilch VOL Sg pp Ia or HB 250 re WG HIF Lead help Look for the lead reference by click it Keep Keep the value display on the screen Sg any 84 68 85 987 Refurbish re HIF WO Refurbish the display of the screen 47 PDF 4E pdfFactory Pro iwWHIWeA est www fineprint cn ADTO3O055 User manual Chapter 9 User Setting Click the button Setup on the main interface to enter the user setting interface Users can setup language date amp time aaaea anea eaea calibration system information user information or file management on the user setting interface 9 1 Language Setting The user can select Chinese or English by click the different language button on EEEE Language Setting interface 9 2 Date and Time Click the button Date amp Time to enter date and time setting interface Please EE input year month date hour minute in sur rh Za Wes vous s LS ge order by the
30. ms Depending on the playback time user can select either 10 20 30 or 40 pictures 8 Lead help Select Lead help for wiring diagram to show how to set up RR ng aed a Vg SI i la mE uj d kor rir i 1 nr WS pF ek mu bie AI TREE Ei hl le rom oim A Se ar a het KA 20 PDF x4 pdfFactory Pro iwWHIWeA Get www fineprint cn User manual 9 Save and Print d Click Freeze and the following screen should be shown as in Figure Users can print save or replay the current displayed waveform or pictures recorded from Capture function When finished select RUN to go back to the current waveform display 10 Exit Lanie mcp lay ub reln L Lutaive Jl LHspal Jan d IHoglt LISS A TE ren ar SS select EXIT to go back to the main menu 26 PDF NAWA pdfFactory Pro TAUABOANGUEE www fineprint cn ADTO3O055 Chapter 4 Caution Do not attach or remove the test leads from the coil wire when the power of the main unit is ON User manual Primary Ignition 2 4 1 Introduction 1 Testable Primary Ignition Type Distributor type External coil Distributor External Coil On Plug COP ignition systems 2 Waveform Display mode Single cylinder parade raster 3 dimensional firing kV superimposed dwell and probe These waveform display modes illustrates the firing kV and burnt time of the ignition system 4 2 Testing procedures The follo
31. nit Then turn on the main unit by press the power button Note Make sure the power is OFF before changing or removing the CF card from the main unit 2 1 2 Power Supply There are three methods to get power for the main unit 1 DC adaptor Plug in the DC adaptor to the wall socket to obtain a 12V DC power 2 Vehicle Battery 1 Connect A side of the cigarette lighter cable with A side of the battery cable as shown in the left picture T DC adapter 2 Clamp the red clip to positive lt terminal of the battery and black clip to Tg negative terminal of the battery Battery cable Re 3 Connected the B side to Star pro main unit 3 Cigarette lighter cable 1 Insert A side of the cigarette lighter cable into the cigarette lighter cable socket on the vehicle Cigarette lighter cable 2 Connect B side to Star pro main unit 8 PDF 4E pdfFactory Pro iXABOGUEE Www fineprint cn ADTO3O055 User manual 2 1 3 Start procedure Press the power button for 2 seconds t enter main interface AUTO3OSS E E Calibration the creen Press anywhere with the touch pen ta enter calibration interface Nih Update by USB mode Click USB icon on right up positon to enter USB mode Select Analyzer ADTO3OSS PDF 4E pdfFactory Pro wHIWeA Gt www fineprint cn ADTO3O055 User manual 2 1 4 Main menu introduction Load paper Print LEM ECU simulation demo
32. o go back to the current waveform display 37 PDF cee EAI pdfFactory Pro PIR Gt www fineprint cn ADTU3O055 User manual Chapter 6 Automotive Oscilloscope Auto DSO 6 1 Introduction The Automotive Oscilloscope stores some signal characteristics of automotive components You needn t to set trigger level when testing It is an easy to use tool 6 2 Testing procedures The testing procedures of the automotive oscilloscope is as follows 1 Connecting the main unit to the converter through the main test cable 2 Supply 12V power through battery cable 3 Perform zero calibration 4 Connect the test leads 5 Choose component of testing 6 Save and print Caution Do not attach or remove any test leads from the coil wire when the power of the main unit is ON 6 2 1 Zero calibration Zero calibration is to verify the data communication between the main unit and the converter is good 6 2 2 Test lead connections Connect the test point to ChA ChB ChC and ChD by the red yellow blue and green cables You can choice connect how many and which channel by necessary Connect the ground wire to the port of the converter on one side and mount the end to the negative side of the battery or to the chassis ground 38 PDF x4 pdfFactory Pro wHIWeA Gt www fineprint cn ADTO3O055 User manual 6 2 3 Choose component of testing Sensors Oxygen sensor MAP Analog MAP Digital TPS EGR
33. plug wire from the coil pack to the spark plug Then connect the Sync Probe to the jumper spark plug wire that was installed Connect the primary ignition lead to the converter and to the negative pole of the primary coil Connect the BNC side of the ground wire to the port of the converter on one side and mount the clip side of the ground wire to the negative pole of the battery or chassis ground Ensure all cables and test leads are clear from any rotating parts like cooling fan Start the engine and begin testing Caution When mounting the SYNC probe to the coil wire make sure the side with AUTOBOSS label is facing the coil Due to the different vehicle makes and models the orientation of the coil configurations may be different If for some reasons the ignition waveform cannot be viewed simply reverse the orientation of the SYNC probe PDF cee EAI pdfFactory Pro iWHIWeA Gt www fineprint cn ADTO3O055 User manual 4 2 3 Vehicle Configuration The primary ignition pattern display can be selected by the following three categories 1 Select by Ignition Mode Click Ignition Mode Select and press Ok button Then Select the followings Distributor External Coil Distributor Internal Coil Coil on plug COP Select number of cylinders 2 3 4 5 6 8 10 12 PDF NAWA pdfFactory Pro JAWARASONGEE www fineprint cn User manual Select Firing order and click OK to enter P
34. r Signal Waveform 58 PDF HEH pdfFactory Pro wWAHARA Gs www fineprint cn
35. rd 3 The screen can not display in order Answer Restart the unit This indicate there is any BUG in the program Please contact AUTOBOSS customer service center or download the latest DSC program from AUTOBOSS website and update the unit 4 The form or data can not be saved Answer If the wave form can not be saved maybe the CF card is full Please delete some old form or change a large size CF card 5 The response is incorrect when the touch pen clicks the screen Answer Do the screen calibration Click the settings and select screen calibration then do the operation by the hints on the screen 6 No response when click the screen Answer contact AUTOBOSS customer service center or your local distributor or download the latest DSC program from AUTOBOSS website T The screen display is not clear Answer Adjust the screen display or color in settings menu 8 The screen color is not the same on the same unit Answer The screen may have fault please contact AUTOBOSS customer service center or your local distributor 56 PDF cee EAI pdfFactory Pro WAIRERE www fineprint cn ADTO3O0S55 User Maunal Appendix 1 Secondary ignition patterns Power and waster Single cylinder display Super imposed Haster Power to waste ratio 57 PDF EH pdfFactory Pro AMARA www fineprint cn ADTOI055 User Maunal Appendix 2 General Scope Waveform LU LIL LIA WIA Mass Air Fluid MAF CAN Injecto
36. read this manual thoroughly y The current user manual is based on the current features and functions available Any added features and functions of Star Pro will be added to the user manual in the future Any updated version of user manual will be available at AUTOBOSS website http Avww autoboss net y When reading the manual please pay special attention to the words Note Caution or Warning read it carefully to ensure the safety Operation precautions 1 Product operation safety y When getting power from vehicle s battery make sure to attach the red clamp of the battery cable to the positive side of the battery while black clamp to the negative side of the battery y Make sure you have connected the ground lead before test y Use the dilapidated test lead may damage the unit y When testing the vehicle do ensure the ventilation is sufficient to prevent inhalation of exhaust gas y During testing do ensure all the test leads and cables are correct connected and not in direct contact with any hot objects y Alarge majority of the vehicles is equipped with a high voltage ignition system especially on electronic ignition and Coil On Plug ignition system This high voltage ignition system will stop human s heart from beating Therefore extra caution is required when testing these systems When the engine is running test operator is prohibited from touching any secondary coil or high voltage wires 2 Star Pro main
37. ri Ignition testing interface 2 Select by Vehicle Manufacturer Select the region of manufacturer Asia car includes vehicle makes from Japan Korea and Southeast Asia Europe America cars include vehicle makes from Europe and America China car includes al makes from China Select Vehicle manufacturer Select number of cylinders The number of cylinders 2 3 4 5 6 8 10 12 30 PDF IEH pdfFactory Pro iH AAG www fineprint cn ADTO3O0S55 User manual Select the engine model Click ok to start test 3 Select by Last test record Select one and press ok to start test 4 2 4 Adjustment and setting oame as secondary ignition 31 PDF x4 pdfFactory Pro iwHIWRA Gt www fineprint cn ALTOTOS55 User manual Chapter 5 General Oscilloscope DSO 5 1 Introduction The 4 Channel Oscilloscope is an easy to use and versatile tool that allows access to any automotive computer controlled circuit 5 2 Testing procedures The testing procedure of the general oscilloscope DSO is as follows Caution Do not attach or remove any test leads from the coil wire while the power of the main unit is ON 1 Connecting the main unit to the converter through the main test cable 2 Supply 12V power through battery cable 3 Perform zero calibration 4 Connect the test leads 5 Channel controls 6 Save and print 5 2 1 Zero calibration Zero calibration is to verify the data
38. sitive poles will be cylinder 1 and 2 while cylinder 3 and 4 will be negative poles The followings illustrates the setup of the leads 1 Triggering Select T Cylinder Designate the coil wire mounted by Sync Probe as the triggering cylinder usually cylinder 1 2 Polarity oelect Signal to identify the polarity of the signal in power and waste ignition System In Power waster ignition system the negative pole of the ignition coil is cylinder 3 and cylinder 4 ao Frei 3 Trigger position settings Tro prz l lun n Select Position Users can adjust the trigger cylinder position to adjust the waveform displayed on the screen 24 PDF 4E pdfFactory Pro iwWHIWeA est www fineprint cn User manual 4 Prope Select prope Position is used to control the sensitivity of the signal from the probe Three selections are currently available High 15 Medium 45 Low 75 5 Display mode selection Select Display Mode gt Single Cylinder Parade Raster 3 Dimensional Firing kV Bar chart Superimposed Dwell and Probe These variety of waveform display illustrates firing kV and burnt time etc 6 Position setting Select Posi from the men to adjust the X and Y division levels Use the up down left or right arrow button to magnify shrink enlarge or shorten the waveform 7 Capture Select Capture Capture is used to record the snapshots of the current wavefor
39. te If your personal computer connected more than one moveable disk please enter my computer and make Sure you find the right one which belongs to Star pro So this can ensure the update success and also protect the data on other moveable disks 52 PDF NAWA pdfFactory Pro PIR Get www fineprint cn ADTO3O055 User manual 10 2 2 Update program downloading instruction Login in AUTOBOSS website http www autoboss net Select English version and enter download center oelect download on the main interface of AUOTOBOSS website and enter Star pro download section to download the program or operation system and save them to your personal computer 10 2 3 Diagnostic program update 1 Download the relative programs in Chinese car European car or Asia car section to your personal computer Save them on the desktop 2 Connect Star pro with PC as per the connecting method we introduced in section 10 2 1 and enter USB update mode 3 Executing the update programs which you just download form AUTOBOSS website and saved on the desktop Click the installation by the hints on the screen until you finished the whole operation See the left diagram 4 Safely remove the USB device and disconnect the USB cable restart the unit to finish the upgrading El eue Note Make sure you removed the USB device If you forgot this step may lead the update failed and you should redo every step 10 2 4 OS update
40. te by themselves 9 3 3 Save as default Save the accurate calibrated values as default 49 PDF 4E pdfFactory Pro wWHIWeA Get www fineprint cn ADTO3O055 seals Ira En SEED ITEM MEE L J Wer Pri lor li basse Lar Fl PPS JIAP FAI dere a Erang Tan fo eye dek ja eS EFL Ther Fue nm gs Pe Le rii HITI User manual 9 3 4 Use default Use the last accurate calibrated values as default 9 4 Basic Information The User can check basic information of the diagnostic scanner such as the hardware version software version S N number after click the Enter See the picture shown on the left 9 5 User Information The User can change or browse the User Information Browse User Information 50 PDF cee EAI pdfFactory Pro iwWHIWeA Gt www fineprint cn User manual Change User Information 7157 eS cel Ther Poe Waa ty Pee ug m Select the items to be changed with the touch pen and input the amendments through the built in keyboard The items include name phone fax and address Click space between two words Click _ to delete the letters Click Enter to save the amendment 9 6 Memory Management There are three modes for memory inquiry 1 Inquiry by testing unit Including primary ignition secondary ignition general scope Automotive oscilloscope Engine analyzer digital multimeter and Exhaust fume analyzer 2 Inquiry by waveform Includin
41. tive 1 amp 2 The cylinder to ignition coil negative 3 amp 4 1 Connect one side of SYNC probe to H port of converter another side to high voltage lead of whatever cylinder 2 Connect one side of 4 chanel sec Ignition probe Red to SEC IGN of the converter another side to the cylinder distributor lead of cylinder 1 and cylinder 2 that is positive side of the Sec Ignition output side 3 Connect one side of 4 chanel sec Ignition probe Black to SEC IGN of the converter another side to the cylinder distributor lead of cylinder 3and cylinder 4 that is negative side of the Sec Ignition output side 4 connect one side of the ground cable to ton the converter another side to the negative pole of battery or ground cable of the vehicle 5 Make sure all cables or leads are keep away from the rotating parts of the vehicle 6 Start the engine and begin testing Caution When using the SYNC probe the mounting direction is very important Typically the side with label AUTOBOSS should be facing the coil Due to different makes and models the orientation may be varied If for some reason the proper signal can be viewed simply reverse the orientation of the mounting PDF cee ERI pdfFactory Pro iWHIWRA GME www fineprint cn ADTO3055 User manual 3 2 3 Vehicle Manufacturer On the main menu select Sec Ignition button the following three choices will be available 1 Ignition Mod
42. unit maintains y Avoid shaking the main unit as it may damage the internal components y During testing avoid unplugging the power cable y Do not use hard or sharp objects to click the touch screen LCD do not punch on jii PDF 4E pdfFactory Pro iwWHIWeA est www fineprint cn ADTO3O055 User manual the touch screen display Do not let the touch screen exposed to the sunlight for a long time y dfnotused for a long time please turn off the power This can extend the life of the main unit y Caution Stay from water or moisture y Perform calibration every time before testing to keep the accuracy of the LCD y Do not pull out or insert the main communication cable when the main unit is working y Keep the main unit away from strong magnetic field during the testing in order to avoid the interference 3 CF card maintains y Plug the CF card when the main unit is working may damage the CF card permanently y Keep the CF card away from magnetic field y Donot plug or insert CF card too frequently y When inserting the CF card into the main unit make sure you get the right direction Normally the side with the label is facing up y Incase CF card is damaged and the program in the card cannot be used please use the following procedures to remake the CF card 1 Login AUTOBOSS website www autoboss net and download the necessary programs to your personal computer 2 Format the CF card to FAT32 3 Write the pro
43. verter SC Connect the ground wire to the port of the converter on one side and mount the end to the negative side of the battery or to the chassis ground Ensure all cables and test leads are clear from any rotating parts such as fan Then turn on the main unit and start the engine to begin testing Starter test Connect the current clamp to the starter positive cable and connect the other side of current clamp to the CURRENT and CURRENT port of the converter Connect the ground wire to the port of the converter on one side and mount the end to the negative side of the battery or to the chassis ground Ensure all cables and test leads are clear from any rotating parts such as fan Then turn on the main unit and start the engine to begin testing 7 2 3 Adjustment and setting Current clamp selection 1mV 10mA 1mV 100mA 1mV 1000mA Voltage Current exchange It can exchange between voltage mode and current mode PDF cee EAI pdfFactory Pro WAIRERE amp ww fineprint cn User manual 1 En Save and print Mir Panak vlt deen Lig Pom lz sc Pile IE Click Freeze and the following screen should be shown as in Figure Users can print save or replay the current displayed waveform or pictures recorded from Capture function When finished select RUN to go back to the current waveform display PF Lh Aplr Lara 45 PDF NAWA pdfFactory Pro TAUABOANGUEE www fineprint cn ADTO3O055 User manual
44. w fineprint cn ALTOTOSS User manual Free Run Free run trigger type is in fact a mode that eliminates the trigger function Trigger level Trigger level determines the height of the signal that must be met for the Star Pro to trigger and display the acquired signal You can adjust the height of the trigger level by using the 1 and touch screen buttons Trigger position Trigger position determines the horizontal position where the trigger level condition is met The trigger position can be move to any horizontal location on the signal display area in increments of 596 by and touch screen buttons Trigger edge Trigger edge works in conjunction with the trigger level Any signal that meets the trigger level condition and your choice trigger edge Rising and Falling is displayed at the trigger position If Hising Edge is selected only a rising signal that reaches the trigger level and transitions to that voltage from a lower voltage meets the trigger conditions and displayed A Falling Edge trigger works just the opposite Auto set If you don t know the signal characteristic of the component or if you don t want to manually make adjustments Choose Auto set 35 PDF NAWA pdfFactory Pro TiAHABOAGUEE www fineprint cn User manual 3 Default setup The Default button returns the settings back to the factory default settings Grid Display the grid or not a og og dg I og 1
45. wing illustrates the testing procedures of testing primary ignition system 1 Connect the main unit to the converter through main cable Supply power to the main unit through battery cable Perform zero calibration Connect the test leads Select vehicle make and model Adjustment and setting Save and print 4 2 1 Zero calibration Zero calibration is to verify the data communication between the main unit and the converter is good 4 2 2 Test leads connection 1 Distributor ignition Connect the BNC side of the SYNC probe to the SYNC port of the converter Mount the other end of the SYNC probe to the coil wire of the cylinder 1 Connect the BNC side of the read probe to the PRI IGN port of the converter PDF cee ERY pdfFactory Pro iwWHIWeA GME www fineprint cn ADTO3O055 Caution Do not attach or remove the test leads from the coil wire when the power of the main unit is ON 28 User manual Mount the alligator piercing clip of the test lead to the negative pole of the primary coil Connect the BNC side of the ground wire all to the port of the converter on one side and mount the clip side of the ground wire to the negative pole of the battery or chassis ground Ensure all cables and test leads are clear from any rotating parts like cooling fan Start the engine and begin testing 2 Coil On Plug COP ignition Remove the coil pack of the trigger cylinder Place a jumper spark
Download Pdf Manuals
Related Search