Pt 100 Temperature Input Module Type AJ65BT
Contents
1. disposing of this product treat it as industrial waste About Manuals The following product manuals are available Detailed Manual Manual No Pt 100 Temperature Input Module Type AJ65BT 64RD3 AJ65BT 64RD4 SH 4001 User s Manual as Related Manual Manual No AJ61BT11 A1SJ61BT11 CC Link System Master Local Module User s IB 66721 Manual 13J872 AJ61QBT11 A1SJ61QBT11 CC Link System Master Local Module IB 66722 User s Manual 13873 SH 080394E CC Link System Master Local Module User s Manual type QJ61BT11N 13JR64 1 Overview This user s manual explains the specifications part identification and wiring for the products listed below which are used as remote device stations for the CC Link system AJ65BT 64RD3 Platinum Temperature Measuring Resistor Pt 100 Temperature Input Module abbreviated as AJ65BT 64RD3 from here on AJ65BT 64RD4 Platinum Temperature Measuring Resistor Pt 100 Temperature Input Module abbreviated as AJ65BT 64RD4 from here on The AJ65BT 64RD3 is a 3 wire system connecting module for the platinum temperature measuring resistor The AJ65BT 64RD4 is a 4 wire system connecting module for the platinum temperature measuring resistor Hereinafter the AJ65BT 64RD3 and AJ65BT 64RD4 will be collectively referred to as AJ65BT 64RD The AJ65BT 64RD converts temperature data input from platinum temperature measuring resistor Pt 100 abbreviated as Pt 100 from here on or platinum temperat2. 5Fe APPI caD ENTA conform to JIS C 2812 External power supply 24 V DC 18 to 30 V DC f 1 ms failure period 0 38 0 84 kg Ib 1 Conversion speed is the time until it is converted to the corresponding digital value after the temperature has been input and then stored in the remote register When the multiple channels are used the conversion speed is 40 ms x number of the conversion enable channels 3 2 Specifications when Connecting to a Platinum Temperature Measuring Resistor The following explains the specifications when connecting the AJ6E5BT 64RD and a platinum temperature measuring resistor 1 AJ65BT 64RD3 The effect on the measured resistance by the discrepancy in the lead resistance value connected to A b is approximately 0 025 C 10 m Q e The lead resistance value between platinum temperature measuring resistor and AJ65BT 64RD3 should be 100 Q or less per line Platinum temperature measuring resistor 2 AJ65BT 64RD4 The lead resistance value between between platinum temperature measuring resistor and AJ65BT 64RD4 should be 100 or less per line Platinum temperature measuring resistor 3 3 Applicable Systems The CC Link system master modules that the AJ65BT 64RD can use are explained below There are no restrictions when using the Q series master modules QJ61BT11N QJ61BT11 When using the Q series master modules AJ61QBT11 A1SJ61QBT11 use one where the symbo
3. MITSUBISHI Pt 100 Temperature Input Module ___ YG S98 A Sere Mitsubishi General Purpose Programmable Controller User s Manual Hardware Thank you for purchasing the Mitsubishi general purpose programmable controller MELSEC A series Prior to use please read this manual thoroughly and familiarize yourself with the product AJ65BT64RD U HW E Type IB NA 66831 E 0810 MEE Melsi 1996 MITSUBISHI ELECTRIC CORPORATION SAFETY PRECAUTIONS Read these precautions before using this product Before using this product please read this manual and the relevant manuals carefully and pay full attention to safety to handle the product correctly These precautions apply only to Mitsubishi equipment Refer to the CPU module user s manual for a description of the programmable controller system safety precautions In this manual the safety precautions are classified into two levels DANGER and CAUTION Indicates that incorrect handling may cause hazardous lt DDANGER conditions resulting in death or severe injury I I I I I I Indicates that incorrect handling may cause hazardous I Z CAUTION conditions resulting in minor or moderate injury or property damage l Under some circumstances failure to observe the precautions given under A CAUTION may lead to serious consequences Observe the precautions of both levels because they are important for personal and system safety Make sure that the end us
4. ay result in damage to the product After installation or wiring attach the included terminal cover to the module before turning it on for operation Undertightening can cause short circuit or malfunction Ground the FG terminals to the protective ground conductor dedicated to the programmable controller Failure to do so may result in malfunction Use applicable solderless terminals and tighten them within the specified torque range If any spade solderless terminal is used it may be disconnected when the terminal screw comes loose resulting in failure Check the rated voltage and terminal layout before wiring to the module and connect the cables correctly Connecting a power supply with a different voltage rating or incorrect wiring may cause a fire or failure Tighten the terminal screw within the specified torque range Undertightening can cause short circuit or malfunction Overtightening can damage the screw and or module resulting in drop short circuit or malfunction Prevent foreign matter such as dust or wire chips from entering the module Such foreign matter can cause a fire failure or malfunction Place the cables in a duct or clamp them If not dangling cable may swing or inadvertently be pulled resulting in damage to the module or cables or malfunction due to poor contact Do not install the control lines or communication cables together with the main circuit lines or power cables Failure to do so may result in
5. donesia E 08190 Sant Cugat del Valles Barcelona Spain Tel 34 93 565 3131 France Mitsubishi Electric Europe B V French Branch 25 Boulevard des Bouvets F 92741 Nanterre Cedex France TEL 33 1 5568 5568 South Africa Circuit Breaker Industries Ltd Australia Private Bag 2016 ZA 1600 Isando South Africa Tel 27 11 928 2000 Taiwan India Country Region Sales office Tel Mitsubishi Electric Automation Hong Kong Ltd 10th Floor Manulife Tower 169 Electric Road North Point Hong Kong Tel 852 2887 8870 Mitsubishi Electric Automation Shanghai Ltd A F Zhi Fu Plazz No 80 Xin Chang Road Shanghai 200003 China Tel 86 21 6120 0808 Setsuyo Enterprise Co Ltd 6F No 105 Wu Kung 3rd Rd Wu Ku Hsiang Taipei Hsine Taiwan Tel 886 2 2299 2499 Mitsubishi Electric Automation Korea Co Ltd 1480 6 Gayang dong Gangseo ku Seoul 157 200 Korea Tel 82 2 3660 9552 Mitsubishi Electric Asia Pte Ltd 307 Alexandra Road 05 01 02 Mitsubishi Electric Building Singapore 159943 Tel 65 6470 2460 Mitsubishi Electric Automation Thailand Co Ltd Bang Chan Industrial Estate No 111 Moo 4 Serithai Rd T Kannayao A Kannayao Bangkok 10230 Thailand Tel 66 2 517 1326 P T Autoteknindo Sumber Makmur Muara Karang Selatan Block A Utara No 1 Kav No 11 Kawasan Industri Pergudangan Jakarta Utara 14440 P O Box 5045 Jakarta 11050 Indonesia Tel 62 21 6630833 Messung Systems Pvt Ltd El
6. e 4 wire type platinum temperature measuring resistor Constant current circuit CH1 Shield CH4 Internal circuit 1 May be better to connect depending on the operating environment 2 A 4 wire type or 3 wire type platinum temperature measuring resistor can also be used for AJ65BT 64RD4 Connect as shown in the diagrams below when using a 3 wire type or 2 wire type platinum temperature measuring resistor 7 External Dimensions Diagram 2 04 5 installing hole B RATE STATION NO xio Xt o age a i RINO eet Og O54 MODE SDO MODE OFFSET UP RESET 0 NORMAL PD Or 30 SET TESTCH ewo 13 OIO O Co Test O ONA GAIN DOWN MITSUBISHI MELSEC AJ65BT 64RD 142 9 5 63 151 9 5 98 Unit mm in Warranty Mitsubishi Electric shall not be liable for any loss caused by reasons for which Mitsubishi is not held accountable lost business opportunities or unrealized gain on the customer s side resulting from failure of the product or any other damage secondary disaster accident damage to equipment other than the product or disruption of other business operations arising out of special circumstances which may or may not have been predicted at Mitsubishi A For safe use of the product e This product is manufactured as a general purpose product intended for general industrial use
7. ectronic Sadan NO III Unit No15 M 1 D C Bhosari Pune 411026 India Tel 91 20 2712 3130 Mitsubishi Electric Australia Pty Ltd 348 Victoria Road Rydalmere N S W 2116 Australia Tel 61 2 9684 7777 MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN NAGOYA WORKS 1 14 YADA MINAMI 5 CHOME HIGASHI KU NAGOYA JAPAN When exported from Japan this manual does not require application to the Ministry of Economy Trade and Industry for service transaction permission Specifications subject to change without notice Printed in Japan on recycled paper
8. ee decimal places x 1000 Operating ambient temperature Overall 25 5 C accuracy Operating ambient temperature less than 20 C more than 30 C Conversion speed Sampling time Temperature input point 0 1 accuracy for maximum value 0 25 accuracy for maximum value 40 ms channel 4 channel module tem O AJ65BT 64RD3 AJ65BT 64RD4 CC Link station type Remote device station o anen 4 station RX RY 128 points each eee RWw RWr 16 points each Between batch power supply system and ground Between batch power supply system and batch communication system Between batch communication system and batch temperature input Between batch temperature input and ground 500 V AC 1 minute Between the platinum temperature measuring resistor input and CC Link transmission photocoupler insulation Insulation method Between the platinum temperature measuring resistor input and channel no insulation Between batch power supply system and ground Dielectric withstand voltage Between batch power supply system and batch communication system Insulation resistor Between batch communication system and batch temperature input Between batch temperature input and ground 500 V DC more than 10 M Q by the insulation resistance taster RAV 1 25 3 5 RAV 2 3 5 Conforms to JIS C2805 M4 x 0 7 mm 0 03 in x 16 mm 0 63 in MOUE MAUNG ea Installation in the rail is possible too TH35 7 5Fe TH35 7 5Al TH35 1
9. ers read this manual and then keep the manual in a safe place for future reference Design Precautions e Inthe case of a communication failure in the network data in the master module are held Check the communication status information SB SW and configure an interlock circuit in the sequence program to ensure that the entire system will operate safely e Do not install the control lines or communication cables together with the main circuit lines or power cables Keep a distance of 100mm 3 94 inches or more between them Failure to do so may result in malfunction due to noise Installation Precautions e Use the module in an environment that meets the general specifications in this manual Failure to do so may result in electric shock fire malfunction or damage to or deterioration of the product For protection of the switches do not remove the cushioning material before installation e Securely fix the module with a DIN rail or mounting screws Tighten the screws within the specified torque range Undertightening can cause drop of the screw short circuit or malfunction Overtightening can damage the screw and or module resulting in drop short circuit or malfunction Do not directly touch any conductive part of the module Doing so can cause malfunction or failure of the module Wiring Precautions Shut off the external power supply for the system in all phases before wiring Failure to do so m
10. inside 4 Tighten the module mounting screws within the following torque range Tightening torque range Module mounting screws M4 screw 78 to 118 N cm Terminal block terminal screws M3 5 screw 59 to 88 N cm Terminal block mounting screws M3 5 screw 98 to 137 N cm 5 When using a DIN rail adapter install the DIN rail considering the precautions described below a Applicable DIN rail types conform to JIS C 2812 TH 35 7 5 Fe TH 35 7 5 Al TH 35 15 Fe b Space between DIN rail mounting screws When installing a DIN rail tighten the screws with a space of less than 200 mm 7 9 in 6 Wiring Wiring Example with CC Link Module The twisted cable connections between the AJ65BT 64RD and master module are as follows Master module rae AJ65BT 64RD I O module or like ue 7 Termination resistor TL PA White Termination resistor Yellow CC Link dedicated cable CC Link dedicated cable For the modules at both ends of the data link make sure to connect the terminal resistor that is attached to a master module Connect between DA and DB 6 2 Precautions when Wiring To obtain maximum performance from the functions of AJ65BT 64RD and improve the system reliability a wiring with high durability against noise is required The following describes the external wiring precautions 1 Use separate cables for the AC and the external input sig
11. l shown below 9707 B or later is recorded in the DATE column on the rating name plate The master modules that do not have 9707 B recorded on the DATE column cannot be used lt Large type gt lt Small type gt MITSUBISHI CPU UNIT PROGRAMMABLE CONTROLLER ODEL DATE 9707 B FA MITSUBISHI ELECTRIC CORPORATION JAPAN BD992D008H40 A MITSUBISHI EYECTRIC BD992D008H40 Manufactured Function date version Manufactured Function date version 4 Name of Each Part The name of each part in the AJ65BT 64RD is described 2 1 9 Side face B RATE STATION NO 0 X10 j X1 e1 04 ON 1 ano 0 D D3 MODE LRUNO MODE OFFSET UP RESET 0 NORMAL 3 aio SET TEST CH 3 Mt 0 j e l o TEST GAIN DOWN MITSUBISHI MELSEC AJ65BT 64RD Station setting switch Transmission baud rate setting switch MODE switch OFFSET GAIN Offset gain setting switch UP DOWN switch RESET switch LED for operation PW status display SD L RUN LERR Terminal block Platinum temperature measuring resistor type specification pin 5 Handling 5 1 Handling Precautions 1 Because it is made of resin do not drop or given a strong shock to the module case and the terminal block 2 Do not take the printed circuit board of the module out of the case It may result in a failure 3 Be careful not to let foreign matter such as filings or wire chips get inside the module while wiring Remove all foreign matters if any get
12. malfunction due to noise When disconnecting the cable from the module do not pull the cable by the cable part Loosen the screws of connector before disconnecting the cable Failure to do so may result in damage to the module or cable or malfunction due to poor contact Startup and Maintenance precautions e Do not touch any terminal while power is on Doing so may cause malfunction e Shut off the external power supply for the system in all phases before cleaning the module or retightening the terminal screws Failure to do so may cause the module to fail or malfunction Undertightening the terminal screws can cause short circuit or malfunction Overtightening can damage the screw and or module resulting in drop short circuit or malfunction Do not disassemble or modify the modules Doing so may cause failure malfunction injury or a fire Do not drop or apply any strong shock to the module Doing so may damage the module Shut off the external power supply for the system in all phases before mounting or removing the module to or from the panel Failure to do so may cause the module to fail or malfunction Mounting removing the terminal block is limited to 50 times after using a product IEC61131 2 compliant Before handling the module touch a grounded metal object to discharge the static electricity from the human body Failure to do so may cause the module to fail or malfunction Disposal Precautions CAUTION e When
13. nals of the AJ65BT 64RD in order not to be affected by the AC side surge or conductivity 2 Always place a platinum temperature measuring resistor at least 10 cm 3 9 in apart from the main circuit line and AC control circuit line Place a platinum temperature measuring resistor sufficiently apart from circuits with high frequency such as high voltage lines and inverter load main circuits If they are placed close to each other the platinum temperature measuring resistor is influenced more easily by the noise surge or conductivity 6 3 Connecting to the AJ65BT 64RD3 1 The highest accuracy can be obtained if a 3 wire type platinum temperature measuring resistor is used for AJ65BT 64RD3 The following shows a connection example of a 3 wire type platinum temperature measuring resistor Internal circuit Internal circuit 1 May be better to connect depending on the operating environment 2 A 4 wire type or 2 wire type platinum temperature measuring resistor can also be used for AJ6E5BT 64RD3 Connect as shown in the diagrams below when using a 4 wire type or 2 wire type platinum temperature measuring resistor 4 wire type wire type A A B b b SLD L sip 6 4 Connecting to the AJ65BT 64RD4 1 The highest accuracy can be obtained when if a 4 wire type platinum temperature measuring resistor is used for AJE5BT 64RD4 The following shows a connection example of a connecting th
14. only It is not designed nor manufactured for use in an equipment or system affecting human lives e If you are considering to use this product in equipment or systems for nuclear power generation power generation aerospace medical or passenger transport applications consult our sales representatives e This product is manufactured under our strict quality control system However if the product is used in the intended facility in such a way that a failure of the product may lead to serious accident or loss incorporate backup or fail safe functions into the system design Country Region Sales office Tel U S A Mitsubishi Electric Automation Inc Hong Kong 500 Corporate Woods Parkway Vernon Hills IL 60061 U S A Tel 1 847 478 2100 Brazil MELCO TEC Rep Com e Assessoria Tecnica Ltda China Rua Correia Dias 184 Edificio Paraiso Trade Center 8 andar Paraiso Sao Paulo SP Brazil Tel 55 11 5908 8331 Germany Mitsubishi Electric Europe B V German Branch Gothaer Strasse 8 D 40880 Ratingen GERMANY Korea Tel 49 2102 486 0 U K Mitsubishi Electric Europe B V UK Branch Travellers Lane Hatfield Hertfordshire AL10 8XB U K Singapore Tel 44 1707 276100 Italy Mitsubishi Electric Europe B V Italian Branch Centro Dir Colleoni Pal Perseo Ingr 2 F Via Paracelso 12 120041 Agrate Brianza an9 Milano Italy Tel 39 039 60531 Spain Mitsubishi Electric Europe B V Spanish Branch Carretera de Rubi 76 80 In
15. ure measuring resistor JPt 100 abbreviated as JPt 100 from here on to 16 bit signed BIN data up to the first decimal place or 32 bit signed BIN data up to the third decimal place 2 EMC and Low Voltage Commands 1 For programmable controller system To configure a system meeting the requirements of the EMC and Low Voltage Directives when incorporating the Mitsubishi programmable controller EMC and Low Voltage Directives compliant into other machinery or equipment refer to the EMC AND LOW VOLTAGE DIRECTIVES chapter of the User s Manual for the CPU module used The CE mark indicating compliance with the EMC and Low Voltage Directives is printed on the rating plate of the programmable controller 2 For the product For the compliance of this product with the EMC and Low Voltage Directives refer to the CC Link module section in the EMC AND LOW VOLTAGE DIRECTIVES chapter of the User s Manual for the CPU module used 3 Specification 3 1 Performance Specification The performance specification of the AJ65BT 64RD is shown below And refer to master module user s manual which is used about the general specification tem AJ65BT 64RD3 AJ65BT 64RD4 Measurement method Connectable platinum temperature measuring resistor Pt 100 JPt 100 Output current for detecting 16 bit signed binary 1800 to 6000 Temperature detection value to one decimal place x 10 value 32 bit signed binary 180000 to 600000 value to thr
Download Pdf Manuals
Related Search