TT04 Vehicle Tracking Systems
Contents
1. Homologation Directive for 04 Vehicle Tracking Systems VERSION 3 0 31 March 2014 Requirements and testing methods for vehicle tracking systems Issued by the Insurance Bureau for Vehicle Crime Stichting VbV Effective 1 April 2014 TABLE OF CONTENTS 1 ADMINISTRATIVE PROVISIONS osiota sete cored due ce 3 2 TECHNICAL DEFINITIONS nit trat tote nu tta rk n nai rh tape e nane dee 5 3 CLASS BREAKDOWN OF VEHICLE TRACKING 6 4 VEHICLE TRACKING SYSTEM REQUIREMENTS 22 4 40 7 5 TEST DESCRIPTIONS ret ep Ri a pd X RAD REUS 13 6 EXAMINATION TEST MATRIX ss 2 i tette emt terete derek we a ena aue 15 7 FOLLOW UP INSPECTION TEST MATRIX i eee op 15 8 TZ POWER SUPPLY TESTS I7 iiti titt irre vac D ieee XR aUa 16 ANNEX 1 Certification agreerright eerie eter rrt ese tert ede unn deb eb eser cde der eb chap rae dents 17 VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 2 1 ADMINISTRATIVE PROVISIONS The administrative provisions applying to this Homologation Directive as described in VbV Administrative Provisions AB04 version 1 1 1 7 Transition period This directive shall replace any prior directives A transition period has been set lasting until 1 January 2015 Any approvals issued previously shall therefore e2. 5 2 8 T8 Jamming detection test Here the requirements should be tested as described in Section 4 3 VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 14 6 EXAMINATION TEST MATRIX Component Test module T1 T2 T3 T4 T5 T6 T7 T8 lt S x 5 5 g S ae 8 8 68 5 g da m J 851 5 a g p zb 5i D T T et 3 a 2 z a 4 5 5 lt ud e 2 ERG et et et 2 Entire system X X X X 7 FOLLOW UP INSPECTION TEST MATRIX Component Test module T1 T2 T3 T4 T5 T6 T7 T8 lt E d rj 5 S e ie E 8 5 T z 5 5 5 Q re e i a d m 2 o m3 a a E ERA A m D ct 5 Qu D S a 551 lt a lt a 2 BF 2 EE EE Block 1 X X Block 2 X X Block 3 X X Block 4 X X Block 5 X X Block 6 X X Block 7 x All follow up inspection tests must be preceded by a functional test and a power supply measurement After the performance of the above tests the system must continue to meet the functional requirements of this regulation with the exception of the T7 Power supply test VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 15 8 T7 POWER SUPPLY TESTS 7 Electrical transient conduction along supply lines only The Electrical transi
3. customer data This system must also show how the access to this data proceeds by way of an adequate access threshold This may be achieved by means of a password for example The receiving environment must also be protected from physical and logical access from outside by means of the usual security techniques such as a firewall for logical access control d to prevent data loss the receiving environment must be equipped with a daily backup of all the modified electronic data A RAID 1 construction is permitted for this purpose 4 4 1 2 that continuity for this is provided by means of an agreement concluded with the supplier provider 441 3 Which SOC provides the service and that continuity for this is provided by means of an agreement 4 4 2 All systems must have European coverage i e in all EU member states in terms of positioning services and communications The supplier must provide a declaration to this effect VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 12 5 TEST DESCRIPTIONS 5 7 General 5 1 1 order of the tests to be carried out will be determined by the Test House 5 1 2 The system components will be tested in the form in which they are installed and supplied 5 1 3 The positioning of the system components during the tests to be carried out will be determined by the Test House and if possible according to installation instructions In the event a manufacturer has special requirem
4. dee ETE PETRUS Jobtitle Signature PP TUE SS Companymname eszcosucanss wes 000 bes VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 17
5. Recherchebureaus an organisation set up and equipped for the professional receipt and processing of alarm signals on behalf of third parties Vehicle tracking system The sum of all required components and functions necessary to fulfil the requirements set in this Homologation Directive Standby mode described here as a vehicle tracking system at rest Communication and or position detection modules may be switched off ignition OFF physical and logical input monitoring active On detecting an active physical and or logical input the system must switch on automatically and communication position detection services must be available alarm condition VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 5 3 CLASS BREAKDOWN VEHICLE TRACKING SYSTEMS Vehicle tracking system with jamming detection Consisting of a VbV SCM approved vehicle tracking system with jamming detection that automatically activates immobilisation based on VbV SCM approved immobiliser class 1 that automatically determines the vehicle s position and forwards it to the receiving environment that can perform all the functions and has all the properties as listed in Section 4 of this specification Vehicle tracking system Consisting of a VbV SCM approved vehicle tracking system without jamming detection based on a VbV SCM approved immobiliser class 1 that can automatically determine the vehicle s position and f
6. ately by the system this must occur no later than 180 seconds after communications have been restored 4 2 13 Checks must be performed at least once per week to determine whether the unit can communicate and send its position If no communication is possible verification must take place The test signal verification must be logged by the receiving environment The above to be provided by the supplier in the form of a declaration 4 2 14 Information protocol In the event of a verified theft signal the system must be able to provide at least the following information to the SOC Position Date and time Speed Direction Vehicle identity Ignition status Alarm condition It is not necessary to send the identification details of the vehicle as these may also be available in a database at the operating centre Additional Test House requirement for Sections 4 2 9 4 2 12 and 4 2 15 provided the vehicle is not in a shielded area and communication is possible VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 9 4 3 4 3 1 4 3 2 4 3 3 4 3 4 4 3 5 4 3 6 4 3 7 4 3 8 Jamming detection requirements The system must be able to detect jamming on the frequencies it uses to communicate For the purposes of testing the supplier much provide these frequencies to the testing organisation The immobilisation condition may only be altered subject to proper authorisation Disconne
7. cting and or reconnecting the system or components thereof may not result in a change to the immobilisation status When jamming is detected immobilisation must be activated preventing the vehicle from being able to transport itself upon being restarted The following conditions apply 4 3 3 1 The system must detect jamming immediately and observe a control period of between 30 and 60 seconds 4 3 3 2 If jamming is detected with IGNITION OFF and the jamming continues beyond the control period the system must activate immobilisation no later than 10 seconds after the end of the control period detection 4 3 3 3 If jamming is detected with IGNITION ON immobilisation must be activated if the jamming continues longer than 15 minutes counting from the initial detection Immobilisation must be deactivated automatically once no more jamming has been detected for a period of 10 minutes OD dio 4 3 3 4 If jamming has been detected and remedied according to the above conditions the very next communication with the receiving environment must include a jamming detection report This information must also be made available to the SOC detection Immobilisation may also be activated by the SOC following a verified report by or on behalf of the owner user After verification the Secure Operating Centre must be able to deactivate the immobilisation provided the vehicle is not in a shielded area and communication is possible The sys
8. ent conduction along supply lines only tests shall be carried out in accordance with the standard ISO 7637 2 2004 For the Electrical transient conduction along supply lines only tests the following test specifications apply Requirements Test pulse number Immunity test level IV Functional status classification 12V systems 24V systems 1 100 600 2 50 50 B 2b 10 20 150 200 3b 100 200 A 4 7 16 B for EUT which must be operational during engine start phase C for other EUT s 5b 87 173 C General classification of functional status Class A all functions of a device system perform as designed during and after exposure to disturbance Class B all functions of a device system perform as designed during exposure However one or more of them can go beyond specified tolerance All functions return automatically to within normal limits after exposure is removed Memory functions shall remain class A Class C one or more functions of a device system do not perform as designed during exposure but return automatically to normal operation after exposure is removed VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 16 1 Certification agreement Undersigned parties do declare this agreement with the intention to guarantee the quality of security systems supplied under the approval label in conformity with the requ
9. ents it must be shown that the position in which the tests have taken place is maintained in assembly 5 1 4 System components will be tested in accordance with the test matrix 5 1 5 Atthe end of each test the system components must perform according to the manufacturer s specifications and may not have undergone any deformations and or changes that may impair the operation of the system components at that time or after a period of time 5 2 Test descriptions 5 2 1 T1 Vibration and shock test The frequency must vary from 10 Hz to 500 Hz at a maximum amplitude of x 5 mm and a maximum acceleration of 3 g peak value ECE R97 par 7 2 8 5 2 2 T2 Cold test Temperature T 40 C 2 C Voltage U 9V 402V Acclimatisation time t 4 hours ECE R97 par 7 2 2 1 5 2 3 T3 Heat Test For components installed in the passenger or baggage areas Temperature T 85 C 2 C Voltage U 15V 40 2V Acclimatisation time t 4 hours ECE R97 par 7 2 2 2 5 2 4 T4 Heat test with condensation test Weather resistance Seven days in accordance with IEC 68 2 30 1980 ECE R97 par 7 2 4 5 2 5 T5 Power supply test Power supply tests in accordance with ISO 7637 2 2004 ECE R97 Annex 9 5 2 6 T6 External radiation EMC High frequency external radiation tests ECE R97 par 7 2 12 ECE R97 Annex 9 5 2 7 T7 Combined functionality positioning test Details to follow VbV Homologation Directive for Vehicle Tracking Systems 04 version 3 0 13
10. fications type approval 4 1 5 The vehicle tracking system may not put road safety at risk in any way 4 1 6 Components and functionalities that are connected or applied to the vehicle tracking system but are not described in this homologation directive shall not be included in the approval of the product 4 1 7 The vehicle tracking system may only write signals to the vehicle s DATA BUS if the official importer or manufacturer of the vehicle has provided a written declaration stating that the supplier in question may write to the vehicle s DATA BUS Under no other circumstances is it permitted for a system to write to a vehicle s DATA BUS VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 7 4 2 4 2 1 4 2 2 4 2 3 4 2 4 4 2 5 4 2 6 4 2 7 4 2 8 Design performance and functional requirements All cables except those for the DATA BUS connection must be the same colour this does not apply to OE systems All system components must comply with the homologation requirements and may only be supplied as a whole The type designations and or brand name under which the approval has been granted must be clearly stated on the most important components s that are not visible from the outside while parts visible from the outside such as sensors may not be provided with a recognisable marking A production code must be affixed to the printed circuit board or to the casing of the system enablin
11. g the supplier to determine when and where the system was manufactured This may also take the form of software It must be possible to position the antennae required for the system in such a way that they are not visible from outside the vehicle The power required by the system must come from the vehicle s own battery Average energy consumption of the vehicle tracking system in standby mode may not exceed twenty 20 0 mA measured over a 24 hour period Note to Test House Prior to this test the system must be able to communicate with the receiving environment and adequate GPS signals must be present The system must have an emergency power supply that enables detection and reporting independently and separately from the power supply subject to the following criteria 4271 Test conditions criteria applicable to the system s battery capacity The system must have its own power supply with a minimum capacity defined as follows Using this power supply it must be possible to refresh and forward the vehicle s position to the operating centre at least once every sixty 60 seconds for a period of at least eight hours under normal conditions 4272 The system must finally generate a signal before the actual voltage of the emergency power supply has fallen below the value at which the system can no longer operate This value must be indicated by the supplier An alarm signal must be logged by the receiving environment and forwarded or re
12. irements as laid down in the Homologation Directive 04 To maintain this the certification institute NAME CERTIFICATION INSTITUTE and the supplier approval holder lay down the following arrangements Both parties shall adhere to what is stated in this Directive TTO4 with reference to the Directive ABOA in specific the Administrative requirements and Approval conditions The supplier shall keep record of all complaints made known to the supplier relating to the product s compliance with requirements to the relevant standards These records shall be accessible upon request to the Certification Institute and contain the actions taken by the supplier On behalf of maintenance inspection and publications per approval number a yearly fee is mandatory In case of non fulfilment of one or more of the above mentioned obligations the following sanctions are possible Withdrawal of the type approval Mandatory recall of the denounced products from the market Removal of the product of the List of approved products To this agreement Dutch Law is applicable Legal disputes that DATA not be settled in agreement will be put to the relevant court in Rotterdam So stated and signed in triplicate On behalf of NAME On behalf of the supplier behalf of the approval holder CERTIFICATION INSTITUTE Date weeds wee tud ees divi eT tides TOWh CIy ae exer eH rele eK stele enda Td Pup us vae eR dx e e ai
13. iser separate from the vehicle tracking system VEHICLE TRACKING Scenario 2 Immobiliser integrated into the vehicle tracking system VEHICLE TRACKING OOTA Scenario 3 Immobiliser controlled 2 by the vehicle tracking system via a separate relay VEHICLE TRACKING OOTA Systems with a wireless deactivation method do not need to satisfy these requirements VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 11 4 3 14 The de activation of the immobiliser must remain possible at battery voltages between seven 7 and fifteen 15 volts for 12 volt nominal systems or between 18 and thirty 30 volts for 24 volt nominal systems 4 4 Receiving environment SOC 4 4 1 Ifthe receiving environment is physically located in an SOC the SOC standards automatically apply If the receiving environment is NOT located in an SOC the supplier provider must demonstrate 44 1 14 that the data centre where the receiving environment is located meets the requirements listed below declaration is permitted a The receiving environment must be of fully redundant construction b The receiving environment must have an automatic emergency power supply at its disposal c The receiving environment must be set up according to an authorisation system for access to automated customer data This system must show that staff are authorised separately to gain access to
14. orward it to the receiving environment that can perform all the functions and has all the properties as listed in Section 4 of this specification excluding Sections 4 3 and 5 2 8 PLEASE NOTE The category of Vehicle Tracking System without jamming detection will no longer apply as of 1 January 2015 From this date vehicle tracking systems without jamming detection will no longer be eligible for inspection nor will any more certificates be issued for such systems VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 6 4 VEHICLE TRACKING SYSTEM REQUIREMENTS 4 1 General 4 1 1 Parts of passenger vehicles that indirectly or directly form part of the vehicle tracking system are regarded as system components and must also be submitted for inspection Parts that have previously been included in the vehicle type inspection do not require additional inspection 4 1 2 If the system or a component thereof has been integrated with equipment intended for other purposes this equipment must meet the inspection requirements to the extent that it has an impact on the operation of the system 4 1 3 If requirements exist under Dutch or European legislation for the system or a component thereof they must also comply with or be homologated in accordance with these requirements 4 1 4 The vehicle tracking system must be designed and installed such that every vehicle equipped with it continues to comply with the technical speci
15. ported by the SOC to the owner of the vehicle VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 8 4 2 9 It must be possible to track the system live while alarm condition This means that a position must be sent to the receiving environment at least once every 30 seconds with at least 90 of the positions in the receiving environment being sent successfully 4 2 10 Alarm condition The alarm condition is met under one of the following circumstances 1 As soon as the vehicle is transported across a linear distance from stationary to destination of a maximum of 300 meters with the ignition off 2 By disconnecting the system s power supply The Secure Operating Centre must be capable of retrieving the vehicle s current position at any time following a verified theft signal An initial signal must be received by the receiving platform within one hundred and eighty 180 seconds of the alarm condition having been fulfilled provided the vehicle is not in a shielded area and communication is possible This signal must also always be received by the SOC environment 4 2 11 At the end of each journey the position of the vehicle must be registered and recorded in the receiving environment Only the final position may be stored unless agreed otherwise with the owner user of the vehicle This position must always be accessible by the SOC 4 2 12 If an alarm notification or final position cannot be sent immedi
16. tem must have a deactivation method emergency procedure inside the vehicle to enable the authorised deactivation of immobilisation Manual activation deactivation of immobilisation is permitted The driver must be able to see when immobilisation has been activated only if ignition is on VbV Homologation Directive for Vehicle Tracking Systems 04 version 3 0 10 4 3 9 4 3 10 4 3 11 4 3 12 4 3 13 No matter what the circumstances the immobiliser may only be activated if the ignition has been off for more than 40 seconds The immobiliser may only be deactivated through the use of a numerical random code at least 4 digits in length not a default code Other deactivation methods are permissible provided they meet the requirements set in Homologation Directive 04 If immobilisation is activated it must be impossible to alter the immobilisation status by disrupting the 30 and or 15 and or 31 While being driven variations of 25 in the nominal battery voltage may not cause the system components that effect immobilisation to change status If the system includes an immobiliser activated by jamming detection it must satisfy the following physical requirements The immobiliser may not be housed in the same casing as the deactivation mechanism e g dashboard A wired connection must be present between the dashboard and the immobiliser coded and with a length of at least 20 cm Scenario 1 Immobil
17. tems may be provided in a language other than Dutch German or English 1 3 4 Full technical product documentation i e o Printed circuit board layouts of all the components Electrical circuit diagrams of all the components o Mechanical drawings of all the components o Assembly drawing of all the components 1 3 5 Two complete products to be supplied as in or being put into production The use of prototypes is not permitted VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 1 3 6 1 3 7 1 3 8 Statements for the following items o Code for the on off signal as well as for mandatory coded signals such as those of the following components remote controls transponder numeric keypad electronic key mechanical key Declarations stating that o the system does not write to the vehicle s DATA BUS or o if a written declaration is received from the official importer or manufacturer of the vehicle stating that the relevant supplier of the vehicle tracking system may write to the vehicle s DATA BUS that it is permitted for the vehicle tracking system to write signals to the DATA BUS o the system cannot be turned on or off using remote controls that have not been approved as described in this inspection specification A class description of the composition of the system Submission of the documentation such as drawings and commercial documents on an electronic data carrier is permi
18. tted VbV Homologation Directive for Vehicle Tracking Systems TT04 version 3 0 2 TECHNICAL DEFINITIONS Original Equipped OE a system that has been installed in the factory or factory environment Aftermarket a system or part of a system that has been installed after the vehicle has been delivered Alarm condition the condition of the system when sabotage jamming alarm or moving detection has occurred Communication and position detection modules must be activated Immobilisation A condition which immobilises the vehicle preventing it from being able to propel itself any further once the ignition has been turned off This condition will never affect the vehicle while being driven only its ability to restart DATA BUS A digital system in a vehicle used to send various messages The DATA BUS signal can come in various forms for example low speed CAN BUS high speed CAN BUS and single wire CAN Detection Technical method for detecting a pre defined alarm condition Jamming The electronic disruption of communication and or position detection signals with the aim of making automatic alarm notification and or position detection impossible Receiving environment the infrastructure in which automatic alarm signals are received and processed SOC Secure Operating Centre definition as set out in the Dutch Private Security Organisations and Detective Agencies Act Wet op de Particuliere Beveiligingsorganisaties en
19. xpire by 1 January 2015 at the latest Certificates for products with approvals issued previously will no longer be issued as of 1 January 2015 1 2 Applicability The requirements listed in this directive apply to inbuilt vehicle tracking systems both original equipped and aftermarket in vehicles with the exception of two wheeled vehicles see Homologation Directive TWO1 1 3 Items required for a product inspection Before a product inspection can be considered the testing institute must be provided with the following documents through the Certification Body Where applicable to the product this means 1 3 1 A completed and signed application form for the performance of the relevant inspection 1 3 2 Documentation showing all the capabilities of the product 1 3 3 Auser manual and installation instructions specific to the system provided written in the Dutch language as a minimum 1 3 3 1 The user manual must contain the following Operating conditions Operating instructions The prevention of unnecessary signalling What to do in the event of failure faults A list of the system components relevant to the user 1 3 3 2 The installation instructions must at least contain the following Projection of the system components Electrical and wiring diagrams Tests with checklist Disruption troubleshooter An overview of the system components If applicable the installation instructions for original equipped OE sys
Download Pdf Manuals
Related Search