2M-BL3 User`s Manual
Contents
1. Save Reset Stream1 Setting Codec The codec settings are separated into MPEG4 and H 264 H 264 is also known as MPEG 4 Part 10 This is the new generation compression standard for digital video This function offers higher video resolution than Motion JPEG or MPEG 4 at the same bit rate and bandwidth or the same quality video at a lower bit rate Profile There are 4 pre programmed stream profiles available for quick set up Choose the form of video encoding you wish to use from the drop down list H 264 HP High Profile The primary profile for broadcast and disc storage applications particularly for high definition television applications for example this is the profile adopted by the Blu ray Disc storage format and the DVB HDTV broadcast service H 264 MP Main Profile Primarily for low cost applications that requires additional error robustness this profile is used rarely in videoconferencing and mobile applications it does add additional error resilience tools to the Constrained Baseline Profile The importance of this profile is fading after the Constrained Baseline Profile has been defined 16 H 264 BP Baseline Profile Originally intended as the mainstream consumer profile for broadcast and storage applications the importance of this profile faded when the High profile was developed for those applications MPEG4 SP Simple Profile Mostly aimed for use in situations where low bit rate and low reso2. E Audio Boost Stream Stream 1 Ej Event Normal Condition Boost Condition Framerate 15 15 Event In Bitrate control CB Event Out SMTP E Mail Bitrate 4000 Kbps 4000 Kbps FTP amp JPEG HTTP Server SESS oot Record Event Notification Boost Event Map E System Ra About 34 The Boost feature is used in conjunction with event detection When this feature is turned ON the Framerate and Bitrate in the boost condition can be set to a different value than the ones in the normal condition field When an event is detected the camera will boost the Framerate and Bitrate from the normal condition to this boosted level for the duration of the event Check the box to enable the service e Boost Setting You can set the condition in Normal and Boost mode Boot Stream Select a video stream for each condition in the drop down list Framerate Select a frame refresh rate per second for each condition in the drop down list Bitrate control Select VBR or CBR in the drop down list in Normal Condition You can t change it in Boost Condition Bitrate Select a value for each condition in the drop down list 3 Event Map Event E Basic Configuration Event Map H Live View Event Map List E Video amp Image Event Name Event In Event Out E Audio Event Add Modify Remove Event In Event Out Event Map E System Ej About The event map allows you to change the settings and establish a schedule fo
3. B Model Name 2M D3W 2M D3W j 3M 00 07 D8 17 6D B5 A ign IP M EE oo ne 17c03c 2M D3 1M C3 Name Flat Dome AC DE 48 DD 1E 21 Maintenance 00 07 D8 17 6D 67 2 Login 00 07 D8 17 6C 5F IP Address 192 168 3 146 10 0 1 220 192 168 3 147 192 168 3 148 192 168 3 145 IP Address 192 168 3 146 10 0 1 220 192 168 3 147 192 168 3 148 192 168 3 145 Wireless IP Address Zero Conf IP Wireless IP Address 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 169 254 161 249 169 254 19 156 169 254 144 252 169 254 110 224 169 254 13 243 Zero Conf IP 169 254 161 249 169 254 19 156 169 254 144 252 169 254 110 224 169 254 13 243 Version 1 1 71 T7 Skymobis 1 1 71 T7 Skymobis 1 1 71 T7 Skymobis 1 1 71 T7 Skymobis 2 0 21 T5 Skymobis CAP NUM SCRL Version 1 1 71 T7 Skymobis 1 1 71 T7 Skymobis 1 1 71 T7 Skymobis 1 1 71 T7 Skymobis 2 0 21 T5 Skymobis Mi Emergency Firmware Upgrade CAP NUM SCRL 4 Select Assign IP You cam see a Assign IP window Enter the required IP address Assign IP Address Camera Information 2M D3W H 264 Mini Dame AC DE 48 DD 1E 21 192 168 1 2 Lc j eee Note For more information refer to the Smart Manger User s Manual 10 3 Operation 2M BL3 supports Windows and Mac operating systems The recommended browsers are Internet Explorer Safari Firefox Opera and Google Chrome with Windows NOTE To stream Live and Playback in Browse
4. for searching If you click Start Date or End Date zone displays Search Calendar D Onboot X All 6 Onboot Alarm Trigger X Motion 54 7 Event List Window Event List displays the event s that were recorded in the SD local storage Select a list and click the play button The video clip will be played 3 7 Help The Help information window will be provided as a popup window so that users can open and read it without a need for log in Tt will offer a description on setting and Help page by which users can manipulate the 2M BL3 without a reference to the manual Entry IH Bullet Windows Internet Explorer AE El http 192 165 12 55 help system support php Help E View Support The Log and Reports provide a variety of information on troubleshooting and contact information should you require technical assistances 3 Live View 3 Video amp Image 3 Audio Log J Event The log file records event in the unit since the last system restart and can be a useful diagnostic tool when troubleshooting i Device System Log The System Log provides information about system events System Information Report E Security PE e The Report contains important information about the server Date amp Time Server Report The Server Report provides information about the server status and should be included when requesting report Information found Language here includes the camera s firmware version MAC address
5. 15fps All Resolution TCP IP UDP IPv4 v6 HTTP HTTPS QoS FTP uPnP RTP RTSP RTCP DHCP ARP Zeroconf Bonjour Multi user authority HTTPS IP Filtering Privacy Zone Video Compression TCP Pre and Post Alarm Yes max 8programmablezone ne ____ AAA Yes Continuus Event EA Yes Button Web browser E SmartManager______ Web browser SmartManager _ RJ 45 10BASE T 100BASE TX LUCI A 0 80 non condensing 4459 d 58 Video Resolutions Frame Rate Protocol Security Max Connection API Supported Open Platform Compatible ONVIF File upload via FTP and HTTP Notification via E mail HTTP and Pre and Post Alarm Yes max 8 programmable zone Yes Yes Continuous Event Yes Yes Button Web browser Yes SmartManager Web browser SmartManager RJ 45 10BASE T 100BASE TX 109C 45 C 0 80 non condensing DC 12V 500mA 6 0W PoE 125mA 6 0W with IR on Power over Ethernet IEEE 802 3af ClassO 74 21 x 84 x 173mm 445g API Programming Interface Alarm Events Video Bufferina Motion Detection Network Time Synchronization SD Recording Software Reset Factory Reset Auto Recove Installation Tool Upgrade Ethernet Operating Temperature Operation Humidit Power Consumption Dimensions WxHXD Unit Weight System Requirement for Web Browser Operating System Microsoft Windows OS Series CPU I
6. A Event List A Event Search The description of playback window follows 1 Video Screen You can see the video screen when playing the video clip in the Micro SD memory 2 Playback Buttons To view a recording data in the SD local storage select it from the list and click the Playback buttons 53 14 Go to the first go to the beginning of the video clip 44 Fast backward play Backward play play backward of the video clip 4 Step backward play go back one frame of the video clip w Pause pause playback of the video clip qe Step forward play go forward one frame of the video clip gt Forward Play play forward the video clip We Fast forward play play fast forward of the video clip i Step forward play go forward one frame of the video clip Clip copy copy the video clip amp Zoom In zoom in the video clip 2 Full Screen display full screen of the video 3 Time Chart Display an hour based search screen for the chosen date If there is recording data a blue section will be displayed on a 24 hour basis 4 Search Calendar Search results from the SD local storage in the 2M BL3 connected are displayed monthly If there is a recorded data for a particular date a blue square on the date will be displayed 5 Play Time Displays time of the video playing 6 Event Search Window Select a search option in the drop down list and click GO button You can also enter the time period
7. Manual Trigger Motion Network Loss Event Out Event Map EH System E About This is used to trigger the event every time the network connection is failed Select Enable to activate the Network Loss event 28 2 Event Out Y SMTP E Mail k The 2M BL3 can be configured to send event and error email messages via SMTP Simple Mail Event Basic Configuration Live View El Video amp Image Audio Event Event In Event Out SMTP E Mail FTP amp JPEG HTTP Server Record Event Notification Boost Event Map System About Transfer Protocol Event Out SMTP E Mail SMTP E Mail Setting O Enable SMTP Sender Interval Aggregate events Use mail server Mail server Port Connections security Enable use SMTP authentication User name Password Login method SMTP E Mail Receiver Receiver 1 Receiver 3 Receiver 5 Receiver 7 SMTP E Mail Test Receiver 2 Receiver 4 Receiver 6 Receiver 8 Receiver Save e SMTP E Mail Setting Select Enable to activate the SMTP operation If your mail server requires authentication check the box for Use authentication to log in to this Mail Server Port Enter the host names or IP addresses and port numbers for your mail server in the fields provided to enable the sending of notifications
8. Motion detection windows are configured by Motion or Mask windows Each window can be selected by clicking with the mouse It is also possible to resize or delete or move the window by selecting the appropriate window at the mouse menu on the video screen New Motion New Mask Select 27 To create a motion or mask window follow steps 1 Click the right button of mouse to see the mouse menu 2 Select New Motion or Mask Window in the mouse menu 3 Click and drag mouse to designate a motion area e Motion Detection Setting The behavior for each window is defined by adjusting the Threshold and Sensitivity as described below A motion index is a set of parameters describing Window Name Type Threshold Sensitivity and Dwell Time Window Types is one of Motion and Mask windows Threshold Sets up the threshold for the motion detection Sensitivity Sets up the sensitivity for the motion detection Dwell Time Set the hold time an event lasts for the specified hold time from the point of detection of a motion You can also modify or delete a motion index Select an index and then click the Modify or Delete button Select Enable to activate the motion window WV Network Loss Event EH Basic Configuration Event In Network Loss EH Live View Network Loss Setting EH Video amp Image 9 O Enable network loss El Audio Dwell time 1 180 sec Event Save Reset Event In On Boot
9. system information IP address and network connections El Network Maintenance Parameter List Support The Parameter List shows the server s parameters and their current settings 55 3 8 Resetting to the factory default settings To reset the 2M BL3 to the original factory settings go to the Setup gt System gt Maintenance web page described in 3 5 6 System Maintenance of the User s Manual or use the Reset button on the 2M BL3 as described below Follow the instructions below to reset the 2M BL3 to the factory default settings using the Reset button Reset Button Remove the front cap e Using the Reset Button Follow the instructions below to reset the 2M BL3 to the factory default settings using the Reset button 1 Switch off the 2M BL3 by disconnecting the power adapter 2 Press and hold the Reset button while reconnecting the power 3 Keep the Reset button pressed during about 2 seconds or more than 4 Release the Reset button 5 The 2M BL3 resets to factory defaults and restarts after completing the factory reset Caution When performing a Factory Reset you will lose any settings you have saved 56 4 Appendix 4 1 Troubleshooting Troubleshooting if problems occur verify the installation of the 2M BL3 with the instructions in this manual and with other operating equipment Isolate the problem to the specific piece of equipment in the system and refer to the equipment manual for
10. when enabled the 2M BL3 attempt to configure port mapping in a NAT router on your network using UPnP Note that UPnP must be enabled in the 2M BL3 see System Network UPnP automatic setting The 2M BL3 automatically search for NAT routers on your network manual setting Select this option to manually select a NAT router and enter the external port number for the router in the field provided Notes f you attempt to manually enter a port that is already in use an alert message will be displayed When the port is selected automatically it is displayed in this field To change this enter a new port number and click Save 46 V Zeroconfig Zeroconfig allows the 2M BL3 to create and assign IP address for 2M BL3s and connect to a network automatically System EH Basic Configuration Network Zeroconf El Live View Zeroconf Configuration E Video amp Image 9 Enable Zeroconf Ej Audio IP address 169 254 196 115 B Event Save Reset M System Information Security Date amp Time Network Basic DDNS RTP UPnP QoS NAT Zeroconf Bonjour Language Maintenance Support E About Zero configuration networking zeroconf is a set of techniques that automatically creates a usable Internet Protocol IP network without manual operator intervention or special configuration servers Zero configuration networking allows devices such as computers and printers to connect to a network autom
11. 2M BL3 and is intended for product Administrators who have unrestricted access to all the Setup tools and Operators who have access to the settings for Basic Live View Video amp Image and System Configuration You can configure the 2M BL3 by clicking Setup in the top right hand corner of the Live View page Click on this page to access the online help that explains the setup tools Connect to 197 168 127 710 The server 192 168 12 210 for IP cameras requires a Username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection Remember my password 3 5 1 Basic Configuration When accessing the 2M BL3 for the first time the Admin Password dialog appears Enter your admin name and password set by the administrator Note If the password is lost the 2M BL3 must be reset to the factory default settings See 3 8 Resetting to the Factory Default Settings You can see the device information in this information page Rus Network Cube Camera Basic Configuration a Bss Configuration LEEI Maelachurer s SMO Network Basic Configuration Meda name lil Video A mee Denis name Cubs Camera Audio emare werden 2 21 75_Skrym obu MAC ddr 00 07 04 ec IP dara 1902 1568 3 245 Lime A Ture mkLocal IP address 166 754 135 705 p Vea A miog Were IF address 0 0 0 0 Maira modo NTS
12. Image E Basic Configuration Day amp Night El Live View Video Preview Video amp Image Basic Image AE amp AWB Day amp Night Privacy Masking Webcasting E Audio E Event E System E About MANUA T US S CIN Day amp Night Control Mode Automatic v Threshold High v IR Control Enable IR Max Strength 5 v Save Reset 23 e Day amp Night Control Select the day night mode from among three modes Mode Normally works in day mode It switches automatically to night mode in a dark place Automatic Normally works in day mode It switches automatically to night mode in a dark place Day Always works in day mode Night Always works in night mode e Threshold Select the day night mode threshold A High quickly changes to day mode but slowly changes to night mode A Low quickly changes to night mode but slowly changes to day mode e IR Control Enable IR Set this checkbox to activate IR operation Max Strength Select a value in the drop down list to tune the strength The default setting Is 5 V Privacy Masking The privacy masking function allows you to mask parts of the video image to be transmitted You can set up to eight privacy masks and the color of privacy masks is black Video amp Image E Basic Configuration Privacy Masking El Live View Video Preview Video amp Image Basic Image AE amp AWB Day amp Night Privacy
13. be allowed or denied access accordingly that 39 is if the addresses in the list are allowed then all others are denied access and vice versa See also the online help for more information Note that users from IP addresses that will be allowed must also be registered with the appropriate access rights Guest Operator or Administrator This is done from Setup System Security Users 3 Date amp Time System E Basic Configuration Date amp Time H Live View Current Server Time EH Video amp Image Date 2013 06 05 Time 08 46 07 El Audio New Server Time E Event Time zone E System GMT Greenwich Mean Time Dublin Edinburgh Lisbon London v Information O Automatically adjusts for daylight saving time changes Security Date amp Time Time mode Network O Synchronize with computer time Language Date Time l Maintenance Synchronize with NTP server Support NTP server 192 168 30 1 NTP Interval 12 hour E About O set manually Date 2013 06 05 Time 08 46 06 Date amp Time Format Date Format YYYY MM DD Time Format 24 Hour Save Reset e Current Server Time It displays the current date and time 24h clock The time can be displayed in 12h clock format in the overlay see below e New Server Time Select your time zone from the drop down list If you want the s
14. control TEC E en Maximum bandwidth Neiwork Priority Basic Automatic framerate control DDNS RTP UPnP QoS NAT Save Reset Zeroconf Bonjour Language Maintenance Support E About e DSCP Settings For each type of network traffic supported by your network video product enter a DSCP Differentiated Services Code Point value This value is used to mark the traffic s IP header When the marked traffic reaches a network router or switch the DSCP value in the IP header tell the router or switch which type of treatment to apply to this type of traffic for example how 44 much bandwidth to reserve for it Note that DSCP values can be entered in decimal or hex form but saved values are always shown in decimal The following types of traffic are marked Live Stream DSCP Event Alarm DSCP Management DSCP e Automatic Traffic Control Set a limitation on user network resources by designating the maximum bandwidth Maximum bandwidth In case of sharing other network programs or equipment it is possible to set a limitation on the maximum bandwidth in the unit of Mbit s or kbit s Auto frame rate Selected if not influenced by a network related program or equipment without a limitation on the network bandwidth WV NAT Traversal A broadband router allows devices on a private network LAN to share a single connection to the Internet This is done by forwarding network traffic from the private network
15. provided by the DHCP server Click the View button to see the current settings Use the following DNS server address to enter the desired DNS server by specifying the following Domain name enter the domain s to search for the host name used by the Network Camera Multiple domains can be separated by semicolons The host name is always the first part of a Fully Qualified Domain Name for example my server is the host name in the Fully Qualified Domain Name myserver mycompany com where mycompany com is the Domain name DNS servers enter the IP addresses of the primary and secondary DNS servers Host Name Configuration Host Name enter the host name to be used as device information in the client software or Speco Manager Services HTTP port Enter a port to receive a service through the HTTP Default Port Number is 80 HTTPS port Enter a port to receive a service through the HTTPS Default Port Number is 443 RTSP port Enter a port to receive a service through the RTSP Default Port Number is 554 ARP Ping Setting Enable ARP Ping setting of IP address The IP address can be set using the ARP Ping method which associates the unit s MAC address with an IP address Check this box to enable the service Leave disabled to prevent unintentional resetting of the IP address Gateway Priority Wireless In case of network connection through the wireless AP Wire In case of a wired network conn
16. service e HTTP Server Setting Name The name of the HTTP event server Use a descriptive name URL The network address to the server and the script that will handle the request For example http 192 168 12 244 cgi bin upload cgi User name Password Provide your log in information e HTTP Server Test When the setup is complete the connection can be tested by clicking the Test button 31 v Record E Basic Configuration Event Out Record El Live View Record Setting El Video amp Image Enable Record Elfo Overwrite Event C Continuous Record E Event In Note Continuous Record is not available while using SD Event Out Stream Type Stream 1 SMTP E Mail Pre event 0 10 sec FTP amp JPEG Post event 0 0 60 sec HTTP Server Record Record schedule Event Notification Boost No Recording E Recording Event Map E System El About All Select All Delete Device Setting Device Type Format Device Status No Storage Device Remove Device Information Total Used Available Used Percent Bad Sector 0 00MB 0 00MB 0 00MB 0 00 0 00 Save Reset When the 2M BL3 detects an event it can record video stream in the Micro SD Memory not supplied or NAS Network Attached Device as a storage device Check the box to enable the service e Record Setting Overwrite Click checkbox to overwrite the storag
17. your time zone from the drop down list If you want the server clock to automatically adjust for daylight savings time select the Automatically adjustment for daylight saving time changes 18 From the Time Mode section select the preferred method to use for setting the time Synchronize with computer time sets the time from the clock on your computer Synchronize with NTP Server the 2M BL3 will obtain the time from an NTP server every 60 minutes Set manually this option allows you to manually set the time and date e Date amp Time Format Specify the formats for the date and time 12h or 24h displayed in the video streams Select Date amp Time format from the drop down list Date Format Specify the date format YYYY Year MM Month DD Day Time Format Specify the date format 24Hours or 12 Hours 3 5 2 Live View Y Source Live View EH Basic Configuration Source Live View Video Input Mode Source Video Mode NTSC v E Video amp Image Ej Audio Save Reset amp Event E System E About e Video Input Mode Video Mode Choose Video Mode you wish to use from the drop down list NTSC or PAL 19 3 5 3 Video amp Image V Basic Video amp Image EH Basic Configuration Privacy Masking Video amp Image Basic El Live View OS Video amp Image Capture mode 1600x1200 Max i5fps Basic Image Stream 1 Setting AE amp AWB Day amp Night C
18. 10 Sharpness Controls the amount of sharpening applied to the image A sharper image might increase image noise especially in low light conditions A lower setting reduces image noise but the image would be less sharp Enable flip image Check this box to flip the image Enable mirror image Check this box to mirror the image Enable Noise Reduction Check this box to reduce an image noise 21 WV AE amp AWB y Video amp Image E Basic Configuration AE amp AWB El Live View Video Preview Ed Video amp Image Basic Image AE amp AWB Day amp Night Privacy Masking Webcasting 7 7777 EA ep 2 p fa as ZI dq a E Audio EH Event y El System E About P74 UTE Exposure Control Mode Automatic v Value 5 default Mw Ol Enable Backlight compensation O Enable Flicker free Flicker Mode Enable Long Exposure Max Shutter 1 8 Ww White Balance Control Mode Automatic S Save Reset e Exposure control This page provides access to the advanced exposure control settings for the 2M BL3 Mode Supports exposure modes to control the amount of light detected by the camera sensor based on settings for light conditions The default setting is Auto mode A Automatic Automatically sets the amount of light detected by the image sensor Hold Current Fixes the exposure at its current state Value Select a value in the drop down list to tune t
19. 3 can be set automatically via DHCP or a static IP address can be set manually If IPv6 is enabled the 2M BL3 receive an IP address according to the configuration in the network router There is also the option of using the Internet Dynamic DNS Service For more information on setting the Network please see Setup System Security Network Basic Configuration Ed Basic Configuration Network Users IP Address Configuration Network Video amp Image O obtain IP address via DHCP 9 Use the following IP address IP address 192 168 12 55 Audio Date amp Time Subnet mask 25 25 25 0 Live View Default router y 488 33 a E Video amp Image j Save Reset Ej Audio a Event J System E About Obtain IP address via DHCP Dynamic Host Configuration Protocol DHCP is a protocol that lets network administrators centrally manage and automate the assignment of IP addresses on a network DHCP is enabled by default Although a DHCP server is mostly used to set an IP address dynamically it is also possible to use it to set a static known IP address for a particular MAC address Use the following IP address To use a static IP address for the 2M BL3 check the radio button and then make the following settings IP address Specify a unique IP address for your 2M BL3 Subnet mask Specify the mask for the subnet the 2M BL3 is located on Default router Specify the IP addres
20. 4 NR as aes eMe ceu em enn ere RR 15 3 Video SC IMaGe sceseseseececeeeseeceephe mue eco a a Eu cH uu MER OEH SE nen 16 4 Date AMM eo ee ie neg Bare em gu eo Dea 18 SNAM RI M DE 19 3 9 9 VIdeo e Irflage ease nae ee oePenendadcua scd used RRA ue 20 So EVENE guod des dusiatae e a 28 1 Event E 27 FEVENEGUE eet a seen 29 2 Event MAD sp ita 35 OY SEM E Ra RRE 37 2 SECUTI ere 2s senses cec eee ace oe eee ec Ue ed een 39 3 Dale cc TINE assesses eae ere are AS 40 4 INGEW ORK S822 3s5 see ates eee ee a 41 5 Languages a eee eee 48 6 Mamtenancs 5 a seae sss esse nets see a OS 49 IU PA A ee ed uc eue ES 50 E E ES RS eee 53 31D Playbackessecsesiesesesenecsncuceuuenbie e e rea HaSa 53 3 D gt Sesser asa sea ease sens eens se car ae see ea eae se ree a cce qoM Mu REM ULdene eer ced nte 55 3 8 Resetting to the factory default settings 56 Appendix wont ene t tee eres ts ee store sees sees esses se senses ssensssenssesssessess 57 T I FOUDIESMOO LING e shes eee se See a Neo ooo pandas 57 4 2 Preventive MalhilenaliCe s2s s25 fines saat aes oe eee race seeders eae 57 2 3 Proquet Specit calor a eee are RARAS 58 1 Description The 2M BL3 supports the network service for a sensor image with progressive scan which can be monitored on a real time screen regardless of distances and locations By using its dedicated program many users are able to have an access to t
21. 5DB standby Downloz width 512 height 368 align center hspace 0 vspace 0 gt lt OBJECT gt lt div gt lt HTML gt lt script gt war obj document getElementById HX_Media E System function onInit Image Day amp Night Webcasting El Audio EH Event E About obj Initialize 1 obj ViewLayout 0 obj Connect 0 192 168 12 55 1 stream1 80 3 0 0 obj SetMenuType 0 function onClose obj Disconnect 0 lt script gt lt lili lv Note To use webcasting service the Enable Anonymous viewer login option must be checked Refer to 3 5 1 Basic Configuration gt Users for more details 25 3 5 4 Event 1 Event In V On Boot El Basic Configuration Event In On Boot E Live View On Boot Setting No Ade O Enable on boot El Audio Dwell time 1 180 sec Event Event In On Boot Manual Trigger Motion Network Loss E Event Out Event Map amp System motion event X v Manual Trigger Event amp Basic Configuration Event In Manual Trigger EH Live View Manual Trigger 1 Setting El Video amp Image O Enable manual trigger 1 amp Audio Dwell time 1 180 sec R4 Event z Manual Trigger 2 Setting Event In On Boot Ol Enable manual trigger 2 Manual Trigger Dwell time 1 180 sec Motion a Manual Tri
22. C j Ages 13 1 Users User access control is enabled by default An administrator can set up other users by giving these user names and passwords It is also possible to allow anonymous viewer login which means that anybody may access the Live View page as described below Basic Configuration E Basic Configuration Users Users User Settin Network Video amp Image Enable anonymous viewer login Audio z User List Setting Date amp Time User Name User Group Authority El Live View admin administrator live setup system B Video amp Image Add El Audio E Event Save Reset E System E About The user list displays the authorized users and user groups levels Authority Provides the lowest level of access which only allows access to the Guest i l Live View page An operator can view the Live View page create and modify Operator events and adjust certain other settings Operators have no access to System Options o An administrator has unrestricted access to the Setup tools and can Administrator l l determine the registration of all other users e Enable anonymous viewer login Check the box to use the webcasting features Refer to 3 5 2 Video amp Image for more details 14 2 Network The 2M BL3 supports both IP version 4 and IP version 6 Both versions may be enabled simultaneously and at least one version must always be enabled When using IPv4 the IP address for the 2M BL
23. HTTPS port 443 RTSP port 554 ARP Ping setting Enable ARP Ping setting Save Reset Setting in regard to network can be executed Settings for IP DNS Host Name Port and ARP Ping can be established along with setting for DDNS uPnP QoS Zeroconfig Bonjour and wireless V Basic e IP Address Configuration Obtain IP address via DHCP Dynamic Host Configuration Protocol DHCP is a protocol that lets network administrators centrally manage and automate the assignment of IP addresses on a network DHCP is enabled by default Although a DHCP server is mostly used to set an IP address dynamically it is also possible to use it to set a static known IP address for a particular MAC address Use the following IP address To use a static IP address for the 2M BL3 check the radio button and then make the following settings IP address Specify a unique IP address for your 2M BL3 Subnet mask Specify the mask for the subnet the 2M BL3 is located on Default router Specify the IP address of the default router gateway used for connecting devices attached to different networks and network segments 41 IPv6 Address Configuration Check this box to enable IPv6 Other settings for IPv6 are configured in the network router DNS Configuration DNS Domain Name Service provides the translation of host names to IP addresses on your network Obtain DNS Server via DHCP Automatically use the DNS server settings
24. Masking Webcasting E Audio E Event EH System E About Privacy Masking Setting O Enable privacy masking ID Name Delete Save Reset 24 The privacy masks are configured by Mask windows Each window can be selected by clicking with the mouse It is also possible to resize or delete or move the window by selecting the appropriate window at the mouse menu on the video screen Mew Privacy Mask select Delete Freeze To create a mask window follow steps 1 Click the right button of mouse to see the mouse menu 2 Select New Privacy Mask in the mouse menu 3 Click and drag mouse to designate a mask window area You can also modify or delete a mask window index Select an index and then modify items or delete button Select Enable to activate the privacy masking function Y Webcasting The 2M BL3 can stream live video to a website Copy the HTML code generated on the screen and pastes it in page code of the website you want to display live video Video amp Image E Basic Configuration Webcasting El Live View Webcasting HTML code E Video amp Image Stream 1 O Stream 2 O Stream 3 Basic lt HTML gt lt HEAD gt lt TITLE gt Web Viewer lt TITLE gt lt HEAD gt AE amp AWB body onLoad onInit onUnload onClose gt lt div gt lt OBJECT id HX Media codebase http 192 168 12 55 NautilusV20 DHInc Privacy Masking classid clsid 731D29F4 2872 4542 B85F 539610D7C
25. O INSTRUCTION MANUAL Network IR Bullet Camera 2M BL3 Please read this manual thoroughly before use and keep it handy for future reference WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PROCUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance FCC COMPLIANCE STATEMENT INFORMATION TO THE USER THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES THESE LIMITS ARE DESIGNED
26. On OW Codec Sample Volume Bitrate Fg AI Networks Check Click the Network Check button to get the information about the camera s network setting and traffic You can see the pop up window below 51 Entry IH Bullet Windows Internet Explorer AE B http 192 158 12 5b svystem check network php Network Check Wired configuration Current Status Connected DHCP OF IP address 192 168 12 55 Subnet mask 255 255 255 0 Gateway 192 168 33 1 ONS 168 126 63 1 Wireless configuration Current Status Disconnected Traffic Wired 34 Kbps Streaming service Number of users currently live Number of users currently playback Server connection Live Push Disconnected Event Push Disconnected Hardware Check Click the Hardware Check button to diagnose the camera s hardware like video Entry IH Bullet Windows Internet Explorer http 192 168 12 55 system check_hardware php Hardware Check Image Result MIES ZA UL ASS INES 52 3 5 7 About The following website will provide the support information for the 2M BL3 information and operation http www remotecamplus com support 3 6 Playback The Playback window contains a list of recordings made to the memory card It shows each recording s start time length the event type used to start the recording calendar and time slice bar indicates if the recording is existed or not Playback
27. Policy Choose the form of connection you wish to use from the drop down list for the administrator Operator and Viewer to enable HTTPS connection set to HTTP by default HTTP HTTPS HTTP amp HTTPS e Upload Certificate To use HTTPS for communication with the 2M BL3 An official certificate issued by a CA Certificate Authority must be uploaded from your PC Provide the path to the certificate directly or use the Browse button to locate it Then click the Upload button Please refer to the home page of your preferred CA for information on where to send the request For more information please see the online help V IP Filtering System EH Basic Configuration Security IP Filtering Live View IP Filtering Setting E Video amp Image AT O Enable IP filtering El Audio On Off Priority Policy Start IP End IP 1 Ej Event System Information ul 4 WwW N Security Users HTTPS IP Filtering Save Reset Date amp Time Network Language Maintenance Support E About Checking the Enable IP address filtering box enables the IP address filtering function Up to 256 IP address entries may be specified a single entry can contain multiple IP addresses Click the Add button to add new filtered addresses When the IP address filter is enabled addresses added to the list are set as allowed or denied addresses All other IP addresses not in this list will then
28. TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES 003 CET APPAREIL NUM RIQUE DE LA CLASSE A EST CONFORME LA NORME NMB 003 DU CANADA CE COMPLIANCE STATEMENT WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures HEREBY REMOTECAMPLUS DECLARES THAT THIS PRODUCT IS IN COMPLIANCE WITH THE ESSENTIAL REQUIREMENTS AND OTHER RELEVANT PROVISIONS OF DIRECTIVE 1999 5 EC A COPY OF THE ORIGINAL DECLARATION OF CONFORMITY MAY BE OBTAINED FROM REMOTECAMPLUS SUPPORTOREMOTECAMPLUS COM CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Quo SU V P 10 11 12 15 14 15 16 17 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Cl
29. and image email Reset 1 86400 sec 1 100 messages from the camera to predefined addresses via SMTP Sender Enter the email address to be used as the sender for all messages sent by the 2M BL3 Interval Represents the frequency of the email notification when an event occurs Aggregate events Shows the maximum number of emails sent within each interval server and enter the necessary information To ensure that the login procedure is performed as securely as possible when using SMTP authentication you must define the weakest authentication method allowed User Name Password Enter the User Name and Password as provided by your network administrator or ISP Internet Service Provider 29 Login Method Set the Weakest method allowed to the highest safest method supported by the mail server The most secure method is listed in the drop down list Login Plain e SMTP E Mail Receiver Receiver Enter an email address You can also register the e mail address of recipients up to 8 e SMTP E Mail Test Receiver Enter an email address and click the Test button to test that the mail servers are functioning and that the email address is valid Event El Basic Configuration Event Out FTP JPEG El Live View FTP Setting Video amp Image O Enable FTP El Audio Server Passive mode Event Por
30. atically Without zeroconf a network administrator must set up services such as Dynamic Host Configuration Protocol DHCP and Domain Name System DNS or configure each computer s network settings manually which may be difficult and time consuming Zeroconf is built on three core technologies e Assignment of numeric network addresses for networked devices link local address auto configuration e Automatic resolution and distribution of computer hostnames multicast DNS e Automatic location of network services such as printing devices through DNS service discovery 47 v Bonjour The 2M BL3 includes support for Bonjour When enabled the 2M BL3 is automatically detected by operating systems and clients that support this protocol System El Basic Configuration A Network Bonjour E Live View Bonjour Configuration E Video amp Image i a Enable Bonjour El Audio Friendly name NUT 8203R ACDE48DD1E43 amp Event Save Reset System Information Security Date amp Time Network Basic DDNS RTP UPnP QoS NAT Zeroconf Bonjour Language Maintenance Support Ej About Note Bonjour Also known as zero configuration networking Bonjour enables devices to automatically discover each other on a network without having to enter IP addresses or configure DNS servers Bonjour is a trademark of Apple Computer Inc 5 Language It will be able to select a user language The type of language it will b
31. ation 30 e JPEG Setting Pre event A pre event buffer contains images from the time immediately preceding the event trigger These are stored internally in the server This buffer can be very useful when checking to see what happened to cause the event trigger Check the box to enable the pre trigger buffer enter the desired total length in seconds minutes or hours and specify the required image frequency Post event This function is the counterpart to the pre trigger buffer described above and contains images from the time immediately after the trigger Configure as for pre event Prefix file name This name will be used for all the image files saved If suffixes are also used the file name will take the form prefix suffix extension Additional suffix Add either a date time suffix or a sequence number with or without a maximum value WV HTTP Server Event Ej Basic Configuration E Video amp Image El Audio URL Event Port EXE BI User name Event Out Password SMTP E Mail FTP amp JPEG HTTP Server Test HTTP Server Record Send message Event Notification Boost Event Map amp System E About Event Out HTTP Server El Live View HTTP Server Setting O Enable HTTP server Save Reset When the 2M BL3 detects an event HTTP Server is used to receive uploaded image files and or notification messages Check the box to enable the
32. e able to select is the English the Russian and the Korean System El Basic Configuration Language El Live View Language Setting E Video amp Image Language English v El Audio E Event System Information Security Date amp Time Network Language Maintenance Support E About 48 6 Maintenance System tet can ts Basic Configuration Maintenance Live View Maintenance Restart the server Video amp Image Audio Reset all parameters except the IP parameters Event Reset all parameters to the factory settings System Upgrade ARA Upgrade the server with the new firmware Security Specify the firmware to upgrade Date amp Time i Network SN and click Upgrade Language Note Maintenance Do not turn off the unit during flash upgrade The unit will restart automatically when the Support upgrade is finished 1 5 minites About Backup Save all parameters and user defined script to a backup file Restore Restore current configuration to backup file Specify the backup file to restore and click MESE e Maintenance Restart The unit is restarted without changing any of the settings Use this method if the unit is not behaving as expected Reset The unit is restarted and most current settings are reset to factory default values The settings that are not affected are the boot protocol DHCP or static the static IP add
33. e device Stream Type You can select Stream1 Stream2 or Stream3 Stream1 H 264 or MPEG 4 data Stream2 MJPEG data Stream3 You can select VIDEO or IMAGE Pre event Enter pre event time value for storage device pre recording Post event Enter post event time value for storage device post recording 32 e Record Schedule You can set the weekly recording schedule for each day Drag or click area by a box unit at first Clicking the block toggles the recording between on and off Click the All Select button to set a schedule for the entire week or a whole day respectively e Device Setting Select Device Type to be recorded in the drop down list SD built in SD card CIFS A file format for a NAS device NFS A file format for a NAS device Note1 Common Internet File System CIFS is a remote file access protocol that forms the basis for Windows file sharing network printing and various other network services CIFS requires a large number of request response transactions and its performance degrades significantly over high latency WAN links such as the Internet Note2 Network File System NFS is a network file system protocol allowing a user on a client computer to access files over a network in a manner similar to how local storage is accessed NFS like many other protocols builds on the Open Network Computing Remote Procedure Call ONC RPC system Device Setting Device Type CIFS v Mes Remote dir
34. e settings such as contrast brightness and saturation to improve images before encoding takes place e Micro SD Recording support The 2M BL3 also supports a micro SD memory slot for local recording with removable storage e Improved Security The 2M BL3 logs all user access and lists currently connected users Also its full frame rate video can be provided over HTTPS e Built in Microphone The 2M BL3 provides an integrated microphone e Megapixel Resolution Max 30fps 1920x1080 e POE This 2M BL3 can be powered through PoE which simplifies installation since only one cable is needed for carrying power as well as video controls e ONVIF Profile S This is a global interface standard that makes it easier for end users integrators consultants and manufacturers to take advantage of the possibilities offered by network video technology ONVIF enables interoperability between different vendor products increased flexibility reduced cost and future proof systems 1 3 Layout e Connection Cable NO Nam 9 Desmpto Power Cable Cable for Power source DC 12V Ethernet Cable Cable for Ethernet POE e Camera Dimension See the diagrams below for the exact dimension Dimensions Unit mm 2 Installation 2 1 Connection e Base Installation Cable through the wall or ceiling with the mount base Secure the camera to the wall or ceiling by the camera stand individual purchase Ceiling Mount Wall Mou
35. ean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not o
36. ection 42 Vv DDNS System E3 Basic Configuration E3 Live View E3 Video amp Image El Audio E Event System Information Security Date amp Time Network Basic DDNS RTP UPnP QoS NAT Zeroconf Bonjour Language Maintenance Support E3 About Network DDNS Internet DDNS Dynamic Domain Name Service Ol Enable DONS Note Please remember you have to configure at least primary DNS server in DNS configuration settings to use Dynamic DNS DDNS Server Registered host User name Password Confirm password Maximum time interval Register local network IP address Registered IP address Save Reset e Internet DDNS Dynamic Domain Name Service When using the high speed Internet with the telephone or cable network users can operate the 2M BL3 even on the floating IP environment in which IPs are changed at every access Users should receive an account and password by visiting a DDNS service like http www dyndns com or http www cctv network co kr Enable DDNS Check to get DDNS service to be available Username Enter an ID to access to the DDNS server y UPnP System E Basic Configuration El Live View E Video amp Image El Audio E Event System Information Security Date amp Time Network Basic DDNS RTP UPnP QoS NAT Zeroconf Bonjour Language Maintenance Support E About Netw
37. ectory Capacity GB 1D E Password Address Enter IP address for NAS device Remote Directory Enter directory or folder location to be recorded in the NAS device Capacity Enter the capacity of storage to be used It must be less than the total storage Capacity IP Password Enter ID and Password The 2M BL3 will ask them whenever you access NAS device Check Press the Check button to check the validity of Device Setting data Format Click the Format button to format SD card Device Information Show current SD card information 33 V Event Notification Event Basic Configurati i i or Event Out Event Notification EH Live View Event Notification Setting J Video amp Image TR 9 O Enable event notification El Audio Notification server URL EE Event Notification server port EXT Event In Save Reset Event Out SMTP E Mail FTP amp JPEG HTTP Server Record Event Notification Boost Event Map E System Ra About When the 2M BL3 detects an event Notification Server is used to receive notification messages as a type of XML data format Check the box to enable the service e Event Notification Setting Notification Server URL The network address to the server and the script that will handle the request wv Boost Event El Basic Configuration z Event Out Boost El Live View Boost Setting Ei Video amp Image O Enable boost
38. ed level for the duration of the event Check the box to enable the Function Record When the 2M BL3 detects an event it can record video stream in the Micro SD Memory not supplied or NAS Network Attached Device as a storage device Check the box to enable the Function 36 3 5 5 System 1 Information You can enter the system information This page is very useful when you refer device information after installation System amp Basic Configuration Information amp Live View Device Name Configuration El Video amp Image Device name H 264 Entry IR Bullet amp Audio El Event Location Configuration System Locationi Information Location2 Security Location3 Date amp Time Location4 Network Language Save Reset Maintenance Support amp About e Device Name Configuration Enter the device name e Location Configuration Enter the location information You can enter that by four 2 Security WV Users System Basic Configuration Security Users E3 Live View User Setting amp Video amp Image Enable anonymous viewer login El Audio User List Setting amp Event System User Name User Group Authority admin administrator live setup system Information Tres Add Users HTTPS Save Reset IP Filtering Date amp Time Network Language Maintenance Support El About 37 User access control is enabled by default w
39. erver clock to automatically adjust for daylight savings time select Automatically adjustment for daylight saving time changes From the Time Mode section select the preferred method to use for setting the time Synchronize with computer time sets the time from the clock on your computer Synchronize with NTP Server the 2M BL3 will obtain the time from an NTP server every 60 minutes Set manually this option allows you to manually set the time and date Note Note that if using a host name for the NTP server a DNS server must be configured under TCP IP settings 40 4 Network System E Basic Configuration Network Basic El Live View IP Address Configuration E Video amp Image O obtain IP address via DHCP El Audio 9 Use the following IP address IP address 199 i668 12 55 E Event Subnet mask 255 255 25h 0 EM System Default router 1027 1580 33 g Information Security IPv6 Address Configuration Date amp Time O Enable IPv6 Network Rasi IPv6 address fe80 aede 48ff fedd 1e43 64 D DNS Configuration RTP UPnP O obtain DNS server via DHCP QoS 9 Use the following DNS server address NAT Domain name Zeroconf Primary DNS server 168 126 63 1 Bonjour Secondary DNS server rcm nu Language Maintenance Host Name Configuration Support Host Name NDT 8203RACDE48DD1E43 E About Services HTTP port 80
40. further information Problems Symptoms Possible Causes or Corrective Actions The camera cannot be accessed If using a proxy server try disabling the proxy setting in your by some clients browser Check all cabling and connectors The camera works locally but Check if there are firewall settings that need to be adjusted not externally Check if there are router settings that need to be configured y If using a network switch check that the port on that device Poor or intermittent network i uses the same setting for the network connection type connection speed duplex The amea cannot eee Check that the host name and DNS server settings are correct via a host name When HTTPS is enabled ensure that the correct protocol HTTP Not possible to log in or HTTPS is used When attempting to log in you may need to manually type in http or https in the browser s address bar No image using Refresh and or If images are very complex try limiting the number of clients slow updating of images accessing the camera ier only shown in black amp Check the Video amp Image setting Blurred images Refocus the camera Increased lighting can often improve image quality Check that Poor image quality there is sufficient lighting at the monitored location Check all image and lighting settings in image part client amp Image Stream Check with your network administrator that the multicast Multicast H 264 not displayed in addresses
41. gger 3 Setting Event Out O Enable manual trigger 3 Event Map Dwell time 1 180 sec B System Manual Trigger 4 Setting po a Ol Enable manual trigger 4 Dwell time 1 180 sec Save Reset 26 This option makes use of the manual trigger button provided on the live view page which are used to start or stop the event type manually Alternatively the event can be triggered via the product s API Application Programming Interface wv Motion Event E Basic Configuration 5 Event In Motion El Live View Video Preview El Video amp Image El Audio Ed Event 3 Event In On Boot Manual Trigger Motion Network Loss Event Out Ir LU Er t mm AL Event Map im n V EC Motionen amp System y E About O Enable video motion detection O Day Day amp Night ID Name Type Threshold Sensitivity Dwell Delete 2 55 1 Motion1 Include 3 x 3 1 2 55 2 Motion2 Include 3 X 7 40 Save Reset Motion detection is used to generate an alarm whenever movement occurs or stops in the video image A total of 8 Motion and or Mask windows can be created and configured Motion is detected in defined Motion windows which are placed in the video image to target specific areas Movement in the areas outside the motion windows will be ignored If part of a motion window needs to be masked this can be configured in a Mask window e Pre Viewer
42. he 2M BL3 at once or a single user can monitor various 2M BL3s at the same time It also enables users to play store and retrieve a monitoring image by using a PC All the settings and real time monitoring screens are also provided through an access to the web The 2M BL3 is fully featured for security surveillance and remote monitoring needs It is based on the DSP compression chip and makes it available on the network as real time full frame rate Motion JPEG and H 264 or MPEG 4 video streams 1 1 Components The system comes with the following components SY Mini Camera Installation CD Installation Guide Accessory Kit Notes 1 Check your package to make sure that you received the complete system including all components shown above 2 Adapter for DC 12V is not supplied 1 2 Key Features e Brilliant video quality The 2M BL3 offers the highly efficient H 264 video compression which drastically reduces bandwidth and storage requirements without compromising image quality Motion JPEG is also supported for increased flexibility e Triple streams The 2M BL3 can deliver triple video streams simultaneously at full frame rate in all resolutions up to 1920 x 1080 using Motion JPEG and H 264 or MPEG 4 This means that several video streams can be configured with different compression formats resolutions and frame rates for different needs e Image setting adjustment The 2M BL3 also enables users to adjust imag
43. he exposure The default setting is 5 Enable Backlight Compensation Set this checkbox to activate the BLC operation Flicker Mode Provides the options for flicker 50Hz Select at 50 Hz environments 60Hz Select at 60 Hz environments 22 Enable Long Exposure Set this checkbox to activate the electronic shutter of the camera Max Shutter Select a shutter speed value in the drop down list The default setting is 1 15 e White Balance Control This adjusts the relative amount of red green and blue primary colors in the image so that the neutral colors are reproduced correctly The camera can be set to automatically adjust for the type of light and compensate for its color Alternatively the type of light source can be set manually From the drop down list select the white balance setting suitable for the lighting used for your camera The available options are Automatic Automatic identification and compensation for the light source color This can be used in most situations and is the recommended setting Fixed Incandescent Fixed color adjustment ideal for a room with incandescent a glow lighting and good for a normal color temperature around 2600K Fixed Fluorescent Fixed color adjustment good for fluorescent lighting with a color temperature around 4000K to 5000K Fixed Outdoor Fixed color adjustment for sunny with a color temperature around 6500K to 7500K V Day Night Video amp
44. hen the administrator sets the root password on first access New users are authorized with user names and passwords or the administrator can choose to allow anonymous viewer login to the Live View page as described below e User Setting Check the box to enable anonymous viewer login to the 2M BL3 without the user account When using the user account users have to try log in at every access e UserList Setting This section shows a registered user account Enter a user name and password to be added and register them by pressing the Add button You can see the pop up window as below Add User User Setting Username Password Confirm password User group guest quest OK administrator V HTTPS System E Basic Configuration Security HTTPS El Live View HTTPS Connection Policy E Video amp Image Audio Connection Mode HTTP amp HTTPS v E Event Private Certificate System QUE and click PENES Information Security Note Users When private certificate does not exist default certificate is used HTTPS IP Filtering Date amp Time Save Reset Network Language Maintenance Support E About 38 For greater security the 2M BL3 can be configured to use HTTPS Hypertext Transfer Protocol over SSL Secure Socket Layer That is all communication that would otherwise go via HTTP will instead go via an encrypted HTTPS connection e HTTPS Connection
45. lution are mandated by other conditions of the applications like network bandwidth device size etc Resolution It enables users to determine a basic screen size when having an access through the Web Browser or PC program The screen size control comes in seven modes like 1920x1080 1280x720 640x480 352x240 and 320x240 Users can reset the selected screen size anytime while monitoring the screen on a real time basis Bitrate control Limiting the bit rate helps control the bandwidth used by the H 264 or MPEG 4 video stream Leaving the Maximum bit rate as 5000Kbps maintains consistently good image quality but increases bandwidth usage when there is more activity in the image Limiting the bit rate to a defined value prevents excessive bandwidth usage but images are lost when the limit is exceeded Note that the bit rate control can be used for constant bit rates only The bit rate can be set as Variable Bit Rate VBR or Constant Bit Rate CBR VBR adjusts the bit rate according to the image complexity using up bandwidth for increased activity in the image and less for lower activity in the monitored area CBR allows you to set a fixed target bitrate that consumes a predictable amount of bandwidth As the bit rate would usually need to increase for increased image activity but in this case cannot the frame rate and image quality are affected negatively To partly compensate for this it is possible to prioritize either the frame rate
46. nt e Connecting to the RJ 45 Connect a standard RJ 45 cable to the network port of the 2M BL3 Generally a cross over cable is used for directly connection to PC while a direct cable is used for connection to a hub e Micro SD memory slot Remove the front cap of the camera to insert the SD memory card SD memory card slot Remove the front cap e Connecting the Power Connect the DC 12V power adaptor to the camera 2 2 Network Connection and 1P assignment The 2M BL3 supports the operation through the network When a camera is first connected to the network it has no IP address So it is necessary to allocate an IP address to the device with the Smart Manager utility on the CD 1 Connect the 2M BL3 device to the network and power up 2 Start SmartManager utility Start gt All programs SmartManager SmartManager the main window will be displayed after a short while any network devices connected to the network will be displayed in the list La All Devices 5 a 1M C3W 1 H a 2M D3W 4 ONVIF 3 E Group 3 Select the camera on the list and click right button of the mouse You can see the pop up menu below Le All Devices 5 H a 1M C3W 1 H a 2M D3W 4 ONVIF 3 y Group B Model Name 2M D3W H 2m 03w 2M D3W 2M D3W 1M C3W AC DE 48 DD 1E 21 00 07 D8 17 6D B5 00 07 D8 17 6D 3C 00 07 D8 17 6D 67 00 07 D8 17 6C 5F Flat Dome H 264 Mini Dome H 264 Mini Dome Mini Dome Cube Camera
47. ntel Core 2 Duo 2Ghz or higher 1GB RAM or more 10GB free disk or higher VGA AGP Video RAM 32MB or higher 1024x768 24bpp or higher General performance considerations When setting up your system it is important to consider how various settings and situations will affect performance Some factors affect the amount of bandwidth the bit rate required others can affect the frame rate and some affect both If the load on the CPU reaches its maximum this will also affect the frame rate The following factors are among the most important to consider High image resolutions and or lower compression levels or high bitrates result in larger images Frame rate and Bandwidth affected Accessing both Motion JPEG and H 264 video streams simultaneously Frame rate and bandwidth affected Heavy network utilization due to poor infrastructure Frame rate and Bandwidth affected Heavy network utilization via wireless router due to poor infrastructure Frame rate and bandwidth affected Viewing on poorly performing client PCs lowers perceived performance Frame rate affected 59 Printed in Korea IR Bullet Network Camera http www remotecamplus com QrtASe 60
48. odec H 264 Baseline Profile w Resolution 1600x1200 Y lI Bitrate control CBR v Bitrate 4000 Kbps El Audio Framerate as GOP size 5 f1 30 amp System Stream 2 Setting E About Codec Resolution Framerate 1s E Quality so f1 100 Stream 3 Setting Codec H 264 Baseline Profile v Resolution Same as Stream 1 Y Bitrate control CBR Y Bitrate Kbps Framerate GOP size t 1 30 Save Reset Refer to 3 5 1 Basic Configuration gt Video amp Image for more details 20 Y Image r Video amp Image E Basic Configuration Image El Live View Video Preview Video amp Image Basic Image AE amp AWB Day amp Night YT om Privacy Masking Webcasting El Audio EH Event E System E About aum a L IMAN 2 YES Image Appearance Brightness 5 default vw Contrast 5 default vw Saturation Hue 5 default vw Sharpness 2 default vw Ol Enable flip horizontally O Enable mirror image O Enable Noise Reduction Save Reset Image Appearance This page provides access to the advanced image settings for the 2M BL3 Brightness The image brightness can be adjusted in the range 1 10 where a higher value produces a brighter image Contrast The image contrast can be adjusted in the range 1 10 Saturation Adjust the image s contrast by raising or lowering the value in this field Hue The image hue can be adjusted in the range 1
49. or the image quality whenever the bit rate needs to be increased Not setting a priority means the frame rate and image quality are equally affected Frame rate Upon the real time play users should select a frame refresh rate per second If the rate is high the image will become smooth On the other hand if the rate is low the image will not be natural but it can reduce a network load GOP size Select the GOP Group of Picture size If users want to have a high quality of fast image one by one please decrease the value For the purpose of general monitoring please do not change a basic value Such act may cause a problem to the system performance For the details of GOP setting please contact the service center Stream2 Setting Sometimes the image size is large due to low light or complex scenery Adjusting the frame rate and quality helps to control the bandwidth and storage used by the Motion JPEG video stream in these situations Limiting the frame rate and quality optimizes bandwidth and storage usage but may give poor image quality To prevent increased bandwidth and storage usage the Resolution Frame rate and Frame Quality should be set to an optimal value 17 JPEG resolution Same as the Stream1 Setting JPEG frame rate Same as the Stream1 Setting JPEG quality Select the picture quality If users want to have a high quality of fast image one by one please decrease the value For the purpose of general monit
50. oring please do not change a basic value Such act may cause a problem to the system performance e Stream3 Setting Codec Same as the Stream1 Setting Resolution Select the Stream1 resolution or the Stream2 resolution Bitrate control Same as the Stream1 Setting A Frame rate Same as the Stream1 Setting GOP size Same as the Stream1 Setting When satisfied with the settings click Save or click Reset to revert to previously saved settings 4 Date amp Time Basic Configuration Basic Configuration Date amp Time Users Current Server Time Network Video amp Image Date 2013 06 05 Time 07 42 19 Audio g New Server Time Date amp Time Time zone H Live View GMT Greenwich Mean Time Dublin Edinburgh Lisbon London v El Video amp Image O Automatically adjusts for daylight saving time changes El Audio Time mode E Event Synchronize with computer time System Date Time Es About 9 Synchronize with NTP server NTP server 192 168 30 1 NTP Interval 12 hour O set manually Date 2013 06 05 Time 07 42 18 Date amp Time Format Date Format YYYY MM DD Time Format 24 Hour Save Reset e Current Server Time It displays the current date and time 24h clock The time can be displayed in 12h clock format in the overlay see below e New Server Time Select
51. ork UPnP UPnP Configuration Enable UPnP Friendly name NUT 8203R ACDE48DD1E43 Save Reset 43 The 2M BL3 includes support for UPnP UPnP is enabled by default and the 2M BL3 then is automatically detected by operating systems and clients that support this protocol Note UPnP must be installed on your workstation if running Windows XP To do this open the Control Panel from the Start Menu and select Add Remove Programs Select Add Remove Windows Components and open the Networking Services section Click Details and then select UPnP as the service to add v QoS Quality of Service QoS provides the means to guarantee a certain level of a specified resource to selected traffic on a network Quality can be defined as a maintained level of bandwidth low latency and no packet losses The main benefits of a QoS aware network are The ability to prioritize traffic and thus allow critical flows to be served before flows with lesser priority A Greater reliability in the network thanks to the control of the amount of bandwidth an application may use and thus control over bandwidth races between applications System E Basic Configuration Network QoS H Live View DSCP Setting E Video amp Image Live stream DSCP 0 0 63 Ej Audio Event Alarm DSCP 0 0 63 B Event Management DSCP 0 0 63 M System Automatic Traffic Control Information Security O Enable automatic traffic
52. perate normally or has been dropped CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU QRE QUALIFIED TO DO SO Use satisfy clause 2 5 of IEC60950 1 UL60950 1 or Certified Listed Class 2 power source only ITE is to be connected only to PoE networks without routing to the outside plant 1 3 Contents Description enn menn nee n nene m e 6 LL Components siesena Pneu eH AA 6 1 2 Key Features ceca a ee S i ee 7 Io Layout RC Lu ARA RA ee ee ee 8 Installation rescence sees ssce ns esessessssenessense 9 2 1 Camera Installation lt s gt lt lt sscc2 4 doe Hence eee anta IR ERES tea TRAS SE 9 2 2 Network Connection and IP Assignment 10 Operation 11 Sl ACCESS TON a DEOWSO eet ien ROUEN IM Mam Hu M 11 3 2 ACCESS MOn the Intel Ie beeesseseseeeeepeceeecuoeeeecce de cene uen eMeeteRc e ad eMe AS 12 3 3 Setting the admin password over a secure connection 12 3 4 Mobile App al 12 3 5 2M BL3 Setup 15 3 5 1 Basic CoD Ig ralo esseeeseeeeeeeseeascececcouunetueqepascpepd IP ee TRES 13 DUS Ci Gee ease a ea a A SI HR eed uu 1
53. r set your browser to allow Adobe Flash 3 1 RemoteCamPlus Activation Start a Browser Go to http www remotecamplus com Create User ID Password Login j uus 3 2 Access from a Browser 1 After Login WebViewer will display your registered Cameras and NVRs v v v v e Y v e oa 21001 Ov awe 2 2M BL3 Camera s Live View page appears in your browser 2M BL3 provides several images and video stream formats Your requirements and the properties of your network will determine the type you use The Live View page provides access to H 264 MPEG 4 and Motion JPEG video streams and to the list of available video streams 11 Remote m All Cameras 2 Cube Camera CAMERA 3 Mini Dome T CAM o j m y x E y pma Id CA dean 5 Bullet Cameral CAM m WP 6 Dome Camera 1 CAMERA 01 lt m 408 2i 201 37 02 s 08212013 09 37 01 0821208 0937201 m 08 21 2013 09 37 02 EST E B BE H 3 4 Mobile APP Android and iOS 1 Start Mobile App 2 Type User ID Password P EAST IPCAMERA 004 f All Cameras e 8 i B Q F amp F e Ww tt HB y 1 Cube Camera 1 Cube Camera 2 f y AeA EU uc lt 3 al A pee h y Y i T Du E 08 21 2013 08 48 1 PPS 08 21 2013 09 48 3 Mini Dome 1 C 4 Mini Dome 2 E J 08 21 2013 08 47 13 08 21 2013 09 48 ia 3 q B CS z 12 3 5 2M BL3 Setup This section describes how to configure the
54. r each event trigger from the 2M BL3 You can register the event map up to max 15 35 Click Add button to make a new event map and you can see a popup window as below C Entry IR Dome Windows Internet Explorer 192 168 12 55 Add Event Map General Name Event In Type On boot Event Out O E Mail To e mail address 1 To e mail address 2 To e mail address 3 To e mail address 4 To e mail address 5 To e mail address 6 To e mail address 7 To e mail address 8 Subject Additional info O rre O HTTP server Message O Event Notification O Boost O Record e General Enter the name for a new event map e Event In Select an event type in the drop down list e Event Out E mail Select email addresses you want to send via email that an event has occurred FTP Select checkbox beside FTP to record and saves images to an FTP server when an event has occurred HTTP Server It sends notification messages to an HTTP server that listens for these The destination server must first be configured on the Event In page Enter a message you want to send Event Notification It sends XML messages to an Notification server that listens for these The destination server must first be configured on the Event In page Boost when an event has occurred the camera will boost the Framerate and Bitrate from the normal condition to this boost
55. ress the default router the subnet mask the system time Default The default button should be used with caution Pressing this will return all of the 2M BL3 s settings to the factory default values including the IP address e Upgrade Carry out the upgrade by importing an upgrade file and pressing the Upgrade button During the upgrade do not turn off the power of the 2M BL3 And try an access again after waiting five minutes or longer e Backup Save a setting value that users enter to the 2M BL3 to a user PC e Restore Import and apply a setting value saved to a user PC 49 Note Backup and Restore can only be used on the same unit running the same firmware This feature is not intended for multi configurations or for firmware upgrades 7 Support The support page provides valuable information on troubleshooting and contact information should you require technical assistance System El Basic Configuration Support El Live View The log and report files can be useful for troubleshooting or contacting the support team EH Video amp Image Logs El Audio System Log System log information B Event Event Log Event log information System Reports Information Server Report Important information of the server status Security y SE The unit s parameters and their current settings Date amp Time Network Health Check Language MIR D System Check Important information of system resources Media Check Video and a
56. s of the default router gateway used for connecting devices attached to different networks and network segments Notes 1 DHCP should only be enabled if using dynamic IP address notification or if your DHCP server can update a DNS server which then allows you to access the 2M BL3 by name host name If DHCP is enabled and you cannot access the unit you may have to reset it to the factory default settings and then perform the installation again The ARP Ping service is automatically disabled two minutes after the unit is started or as soon as an IP address is set 3 Pinging the unit is still possible when this service is disabled 15 3 Video amp Image Basic Configuration Basic Configuration Pom Video amp Image Users Sensor Setting Network Video amp Image Capture mode 1600x1200 Max 15fps Audio Date amp Time Stream 1 Setting Codec H 264 Baseline Profile Live View Resolution 1600x1200 v E Video amp Image Bitrate control CBR Audio Bitrate 4000 Kbps Event Framerate 15 Mi System GOP size 15 1 30 About Stream 2 Setting Codec MJPEG Resolution 640x480 v Framerate 15 Quality 50 1 100 Stream 3 Setting Codec H 264 Baseline Profile Resolution Same as Stream 1 v Bitrate control CBR Bitrate 1000 Kbps Framerate 15 v GOP size 15 E ERE
57. t Event in Remote directory Eu IE User name Anonymous login SMTP E Mail Password FTP amp JPEG A JPEG Setting Record Event Notification Pre event Time 5 0 30 sec FPS 1 1 2 fps Boost Post event Time 5 0 30 sec FPS 1 1 21 fps Event Map Prefix file name basename_ Additional suffix O None 9 Date Time O sequence number amp System E About Save Reset When the 2M BL3 detects an event it can record and save images to an FTP server Images can be sent as e mail attachments Check the box to enable the service e FTP Setting Server Enter the server s IP address or host name Note that a DNS server must be specified in the TCP IP network settings if using a host name Port Enter the port number used by the FTP server The default is 21 Use passive mode Under normal circumstances the 2M BL3 simply requests the target FTP server to open the data connection Checking this box issues a PASV command to the FTP server and establishes a passive FTP connection whereby the 2M BL3 actively initiates both the FTP control and data connections to the target server This is normally desirable if there is a firewall between the camera and the target FTP server Remote directory Specify the path to the directory where the uploaded images will be stored If this directory does not already exist on the FTP server there will be an error message when uploading User name Password Provide your log in inform
58. to the outside that is the Internet Security on the private network LAN is increased since most broadband routers are pre configured to stop attempts to access the private network LAN from the public network Internet Use NAT traversal when your 2M BL3s are located on an intranet LAN and you wish to make it available from the other WAN side of a NAT router With NAT traversal properly configured all HTTP traffic to an external HTTP port in the NAT router is forwarded to the 2M BL3 WAN nternet LAN Intranet Broadband NAT Router Port Forwarding Device Notes For NAT traversal to work this must be supported by the broadband router The broadband router has many different names NAT router Network router Internet Gateway Broadband sharing device or Home firewall but the essential purpose of the device is the same 45 System El Basic Configuration s Network NAT Port Mapping H Live View Wire NAT traversal Setting E Video amp Image Wire NAT traversal Setup E Audio A External http port 10000 1024 65535 E Event External rtsp port 10001 1024 65535 System Note Information If the Port is 0 the assigned port of network camera will be set automatically Security Date amp Time HTTP URL Network RTSP URL Basic DDNS RTP Save Reset UPnP QoS NAT Zeroconf Bonjour Language Maintenance Support E About e NATtraversal Settings Enable
59. udio stream information Support RM EA 8 Network setting and traffic information El About GENE A Hardware diagnostic check e Logs The 2M BL3 support system log information Click the System Log button to get the log data e Reports Server Report Click the Server Report button to get the important information about the server s status and should always be included when requesting support Parameter List Click the Parameter List button to see the unit s parameters and their current settings e Health Check System Check Click the System Check button to get the important information about the camera s system resources You can see the pop up window below 50 gt Entry IH Bullet Windows Internet Explorer http 192 168 12 55 system check system php System Check Model Firmware 0 0 6 T8_releaze Date amp Time Date 2013 06 06 Time 04 08 41 Running time 12 min CPU Usage Media Check Click the Media Check button to get the information about the camera s video and audio stream You can see the pop up window below Entry IH Bullet Windows Internet Explorer Sele http 7 192 168 12 55 system check_media php Video stream Stream On Off Codec Size FPS Bitrate Streami On H 264 Baseline Profile 1600x1200 15 3974 Kbps Stream2 On MJPEG 640x480 16 2548 Kbps Stream3 On H 264 Baseline Profile 640x480 5 1048 Kbps Audio stream Type
60. used by the camera are valid for your network Check the client that the Enable multicast checkbox are enabled in the System Network RTP tab Checks with your network administrator to see if there is a firewall preventing viewing l Check if your router supports multicasting or if the router Multicast H 264 only accessible i he cli d th itob fi d by local clients settings between the client an t e server need to be configured The TTL value may need to be increased Color saturation is different in Modify the settings for your graphics adapter Please see the H 264 and Motion JPEG adapter s documentation for more information Check that the SD Card is inserted properly Video cannot be recorded Check that the SD Card is formatted properly 4 2 Preventive Maintenance Preventive maintenance allows detection and correction of minor that faults before they become serious and cause equipment failure 57 Every three month perform the following maintenance 1 Inspect all connection cables for deterioration or other damage 2 Clean components with a clean damp cloth 3 Verify that all the mounting hardware is secure 4 3 Product Specification MainItem Specification Motion JPEG MPEG 4 Part2 H 264 MPEG 4 Part 10 Profiles H 264 HP MP and BP MPEG 4 SP Simultaneously H 264 or MPEG 4 and MJPEG Video Streaming Controllable Frame Rate and Bandwidth VBR CBR H 264 and MPEG 4 1920x1080 320x240
Download Pdf Manuals
Related Search