ROBOTIC VACUUM INSTRUCTIONS & WARRANTY
Contents
1. VOC ROBOTIC VACUUM 2 YEAR LIMITED REPLACEMENT WARRANTY RHRV100 _FA_210314 RHRV100 INSTRUCTIONS amp WARRANTY Spectrum Brands Australia Pty Ltd Spectrum Brands New Zealand Ltd Locked Bag 3004 Braeside PO Box 9817 Newmarket Victoria 3195 Australia Auckland 1149 New Zealand Customer Service in Australia Customer Service in New Zealand Toll Free 1800 623 118 Toll Free 0800 736 776 Email info spectrumbrands com au Email service spectrumbrands co nz Website www spectrumbrands com au Website www spectrumbrands co nz Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Ltd Warranty Against Defects In this warranty Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the Competition and Consumer Act 2010 CGA means the New Zealand Consumer Guarantees Act 1993 Goods means the product or equipment which was accompanied by this warranty and purchased in Australia or New Zealand as the case may be Manufacturer We or us means 1 for Goods purchased in Australia Soectrum Brands Australia Pty Ltd ABN 78 007 070 573 or 2 for Goods purchased in New Zealand Spectrum Brands New Zealand Ltd as the case may be contact details as set out at the end of this warranty Supplier means the authorised distributor or retailer of the Goods that sold you the Goods in Australia or in New Zealand and You means you the original end user purchaser of the Goods 1 Our goods come with2. a Any serial number or appliance plate is removed or defaced b The Goods have been serviced or otherwise repaired by a person not authorised to do so by us or where non approved replaced parts are used 10 The Goods are designed for domestic use only A limited 90 day Warranty applies to any industrial or commercial use of the Goods The Goods must be connected to the electrical voltage requirements as specified in the ratings label located on the Goods 11 This warranty does not cover the cost of claiming under the warranty or transport of the Goods to and from the Supplier or us 12 This warranty is only valid and enforceable in Australia against Spectrum Brands Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Ltd Contact us or the Supplier for further details Register your product online If you live in Australia please visit www spectrumbrands com au warranty If you live in New Zealand Please visit www spectrumbrands co nz warranty Registration of your warranty is not compulsory it gives us a record of your purchase AND entitles you to receive these benefits Product information Hints and tips Recipes and news Information on special price offers and promotions Any questions Please contact Customer Service for advice TABLE OF CONTENTS Warranty 1 Remote control amp Programming 10 Components 4 Space isolator 12 Quick start guide 6 Docking station 14 Battery replacement amp
3. attributable to misuse abuse accident or non observance of manufacturer s instructions on the part of the user As far as the law permits the manufacturer does not accept liability for any direct or consequential loss damage or other expense caused by or arising out of any failure to use the Goods in accordance with the manufacturer s instructions 5 Exhaustible components such as batteries filters and brushes of the Goods are included under this Warranty only where there is a defect in workmanship or materials used 6 The warranty granted under clause 3 is limited to repair or replacement only 7 Any parts of the Goods replaced during repairs or any product replaced remain the property of the manufacturer In the event of the Goods being replaced during the Warranty Period the warranty on the replacement Goods will expire on the same date as for the Warranty Period on the original Goods which are replaced 8 In order to claim under the warranty granted under clause 3 you must a Retain this warranty with your receipt proof of purchase and b Return the Goods to us at the relevant address or to the Supplier by prepaid freight within the Warranty Period accompanied with i the legible and unmodified original proof of purchase which clearly indicates the name and address of the Supplier the date and place of purchase the product name or other product serial number and ii this warranty 9 This warranty is immediately void if
4. guarantees that cannot be excluded under the Australian Consumer Law or the CGA You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure 2 The benefits provided by this Warranty are in addition to all other rights and remedies in respect of the Goods which the consumer has under either the Australian Consumer Law or the CGA The original purchaser of the Goods is provided with the following Warranty subject to the Warranty Conditions 3 We warrant the Goods for all parts defective in workmanship or materials from the date of purchase Warranty Period for the period of a Two 2 years for Russell Hobbs products see product packaging for details b Two 2 years with five 5 year motor warranty for Russell Hobbs products see product packaging for details c Limited Lifetime Ten 10 years for Russell Hobbs cookware d One 1 year for George Foreman If the Goods prove defective within the Warranty Period by reason of improper workmanship or material we may at our own discretion repair or replace the Goods without charge Warranty Conditions 4 The Goods must be used in accordance with the manufacturer s instructions This Warranty does not apply should the defect in or failure of the Goods be
5. the silver charging electrodes on the charging station IMPORTANT Place the charging station securely against the wall or it might be moved by the vacuum making it difficult for the cleaner to dock and charge If your charging station isn t operating correctly it may be necessary to re synchronise it with the R Vac using the following steps Turn off the vacuum and switch on the docking station Using a paperclip or similar press in the internal synchronise button and keep it pressed in Switch on the vacuum using the Power switch 2S s Release the internal synchronise button after the R Vac has emitted a series of beeps indicating it has synchronised NOTE If you fail to hear any beeping during the synchronising repeat the above process MAINTENANCE IMPORTANT INFORMATION Your R Vac may vacuum for you for up to 2 hours but will need approximately 5 minutes of your time after every use to keep it operating in peak condition and to avoid any damage REMOVING AND REPLACING THE DUST BIN 1 Place the vacuum on the ground or on a stable surface 2 Press the button on the dust bin down Refer to Figure 1 and extract the bin by pulling it away from the unit Refer to Figure 2 Figure 1 _ Figure 2 3 To replace the dust bin push it back into the vacuum until it clicks into place 15 CLEANING THE DUST BIN Remove the dust bin 2 Press the two side clips See Figure 1 on the dust b
6. HESE INSTRUCTIONS THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY 19 www russellhobbs com aqu www russellhobbs co nz Become a food T member NS home living for recipes nutrition lifestyle articles amp more www foodandhomeliving com au ke Scan this code to learn more Download a QR Reader App to scan the code RUSSELL HOBBS and logo are Trade Marks of Spectrum Brands Inc or one of its subsidiaries 2013 Spectrum Brands Inc
7. R Vac working for you by following our 3 quick steps 1 Install R Vac s rechargeable battery page 6 2 Charge your R Vac page 8 3 Press the AUTO button to have your home vacuumed for you page 9 Once your R Vac has vacuumed your home it is important to give it a little attention Please spend approximately 5 minutes after each cycle cleaning your R Vac By giving your R Vac this attention it will save you hours of vacuuming each week as well as providing you with a more thorough clean Please refer to the cleaning instructions on page 15 BATTERY INSTALLATION AND REPLACEMENT Installing and replacing the rechargeable battery e wo hf gt Place the robotic vacuum cleaner upside down on a flat stable surface Using the screwdriver provided remove the screws on the battery cover Refer to Figure 1 Lift the battery cover away from the unit Attach the connector on the battery with the connector in the battery compartment by pushing them together until they click into place and are firmly secured Refer to Figure 2 IMPORTANT The connectors will only fit together one way Do not try to force them together if they are not correctly aligned S Hold the battery by the material tabs and lower it into the battery compartment while guiding the cables and connectors into the cavity provided in the bottom of the battery compartment Replace the battery cover and screws Return the vacuum to its upright position Place t
8. ail to hear the beeps while synchronising repeat the above process 10 FUNCTIONS OF THE REMOTE CONTROL To set the current time NOTE The remote control uses 24 Hour time only During set up press the button to quit at any time To set the correct time Press the TIMER button The 1 time digit will flash Use the and Y to change the number Press the lt gt buttons to scroll left and right and change the Hour and Minutes using the and VY buttons Once the correct time is displayed press the TIMER button to lock in the time and start the clock To set the current weekday The numbers at the top of the screen represent days of the week gt I a 1 Monday 2 Tuesday 3 Wednesday 4 Thursday 5 Friday 6 Saturday 7 Sunday Press the TIMER button then press lt The square around a number at the top of the screen will then begin to flash Press the and Y buttons to scroll left and right through the weekdays When your current day is selected lock it in by pressing the TIMER button SCHEDULE PROGRAM YOUR VACUUM You can program your R Vac to begin cleaning automatically by following the steps below A Pre set time Set the time you would like your vacuum cleaner to begin cleaning 1 Press the SET button 2 The hour digit will flash Use the and Y to change the number 3 Pr
9. before removing the battery from the vacuum Remove the vacuum battery by lifting it out of the battery compartment using the material tabs on each side of the battery Disconnect the connector plugs Store the vacuum and battery in a cool dry environment Do not drop or exert external force on the battery Do not attempt to charge the battery from another power source The battery must be recycled in a safe manner check with your local recycler Do not dispose of your battery in a fire In case of battery leakage do not allow the liquid to contact exposed skin or clothes IMPORTANT Store the R Vac Remote Control Space Isolator Charging Station and Batteries in a dry environment below 45 C Old batteries should be recycled safely CHARGING YOUR R Vac Manual charge 1 Manually place the vacuum on charge there are 2 manual charging options a Using the adapter only plugged directly into the DC socket located next to the ON OFF switch or b With the adapter connected to the charging station place vacuum onto the charging station NOTE The vacuum will charge when the Power switch is in the ON or OFF position NOTE The power indicator will flash when the vacuum is charging 2 Charge for at least 12 14 hours before first use or if the vacuum has not been used for an extended period of time 3 When the vacuum is fully charged the power indicator will stop flashing and will remain illuminated For the first c
10. c and will only operate when the R Vac is not located on the charging station For general daily use we recommend using the remote control to start the R Vac from the charging station AUTO button Automatic Cleaning IMPORTANT Before using your vacuum clear any clutter or loose cords in the area you intend to clean The AUTO button is the main method most people use to start their R Vac Press the AUTO button to let R Vac start cleaning Once R Vac starts it uses an algorithm to work through the room with a series of patterns a series of zig zags increasing spirals and edge following to maximise coverage During this time the R Vac can cover areas more than once don t be concerned by this it is part of the normal cleaning process Press any button on the control panel to stop the vacuum cleaning SPOT button spot cleaning The SPOT button is ideal to clean up small spills Pressing the SPOT button will automatically clean an area of approximately 1 square meter The vacuum will operate in spiral mode for 3 minutes and then switch itself off NOTE To stop the vacuum when in spot cleaning mode press any button on the control panel CHARGE button IMPORTANT Ensure you have the Charging Station set up Press the CHARGE button and the vacuum will automatically stop the vacuum motor to preserve power and search for the charging station This is achieved by methodically working through the cleaning area and periodically
11. ess the lt gt buttons to scroll between the Hour and Minutes setting and using the A and Y buttons to set the start cleaning time 4 When the desired start time is shown lock in the time by pressing the SET button B Pre Set the Weekday The numbers at the top of the screen represent days of the week 1 Monday 2 Tuesday 3 Wednesday 4 Thursday 5 Friday 6 Saturday 7 Sunday 11 Press the SET button then press lt The square around a number at the top of the screen will then begin to flash Press the and Y buttons to scroll through the weekdays Oo at OF ol Select the days you would like to schedule your vacuum to clean by pressing the OK button this will underline your number Alternatively press the ALL button if you would like to schedule the vacuum to clean every day IMPORTANT Your R Vac will continue to clean at the scheduled time even if the bin is full or the brushes require cleaning You should empty your dust bin and clean the brushes after every clean NOTE Underlined numbers represent days that are scheduled NOTE You can also press the OK button to deselect days SPEED selection Your R Vac is fitted with a variable speed function which allows the speed of your robot vacuum to be set to one of two levels The standard setting is fast which maximises area coverage For areas where extra vacuuming is required you
12. flat head screw driver position the screw driver down and under the front wheel Pop the wheel of the assembly out using the screw driver and clean the cavity and the axle Refit the wheel TROUBLE SHOOTING Error codes will appear on the remote control ERROR ERROR CAUSE HOW TO SOLVE CODE Ground detection Clean the sensors underneath of the vacuum sensors at the front Middle brush Clean both brushes as per section CLEANING THE MAIN BRUSH AND FLOOR BRUSH Charge vacuum until fully charged then use again Dust bin contact Check the dust bin and ensure it is securely in place Clean the dust bin contacts Incorrect key sequence Clear code from the remote by pressing Set Stop when programming and Set again Ensure remote is out of programming mode before ie nothing is flashing on screen Left amp Right wheel Check the left and right wheels and clean any dust or hair build up If the errors above have been checked and the vacuum is still not functioning correctly please contact customer service for advice Do not disassemble the unit 18 IMPORTANT SAFEGUARDS Basic safety precautions should always be followed including but not limited to the following k Gi ge po P 10 Ws 14 To protect against electrical hazards do not immerse the power adaptor R Vac or any of the associated accessories in water or any other liquid Do not use or charge this appliance outdoors or in wet areas Alwa
13. harge if this occurs prior to 12 14 hours of charging ignore the light and leave the vacuum on charge Automatic charge When the battery power is at a low level the vacuum will emit a series of beeps then automatically stop vacuum motor to preserve energy and search for the charging station The Charge button will illuminate while it is searching If the charging station is detected the vacuum will then make its way to the charging station dock automatically and begin to charge Once on charge the Power indicator will illuminate and flash If the charging station is not set up and the vacuum will continue searching until the battery runs out completely FUNCTIONS Power switch located on the side of the vacuum The power switch is designed to isolate your battery to maximise the effective life When not using charging your vacuum for an extended time you should set the power switch to the OFF position To use your R Vac switch the Power switch to ON and the vacuum will go into standby mode The Power indicator light will illuminate and flash if the battery is not full Tips e The power indicator light will illuminate when the vacuum is in operation e The power indicator with flash when the vacuum is charging e When the vacuum is fully charged the power indicator will stop flashing and will remain illuminated The following function buttons AUTO SPOT amp CHARGE are located on the control panel on top of the R Va
14. he vacuum on charge there are 2 charging options a Using the adapter only plugged directly into the DC socket located next to the ON OFF switch or b With the adapter connected to the charging station and plugged into a wall power outlet then place vacuum onto the charging station NOTE The vacuum will charge when the Power switch is in the ON or OFF position NOTE The power indicator will flash when the vacuum is charging c Allow the vacuum to charge for at least 12 14 hours before first use or if it has not been used for an extended period of time d After charging for at least 12 14 hours your vacuum is ready for use e When the vacuum is fully charged the power indicator will stop flashing and will remain illuminated For the first charge if this occurs prior to 12 14 hours of charging ignore the light and leave the vacuum on charge IMPORTANT When not in use keep the vacuum on charge to get the best performance from the battery Alternatively switch the Power switch to the OFF position when not in use IMPORTANT Only use the rechargeable battery recommended for R Vac Do not use any other rechargeable batteries for this vacuum Figure 1 f Battery Cautions l wo s oY or e 8 If you are no longer using or intend storing the vacuum for an extended period of time remove the batteries from the vacuum space isolator and remote control Set the Power Switch to OFF
15. in to release the gate Push the gate open and pour out the dust 4 Push on the rubber strip to open the clear cover Pour out the dust 5 If required dust the insides of the bin with the brush see figure 2 Figure 1 Figure 2 CLEANING THE FILTER IMPORTANT Do not allow water near the fan assembly 1 Lift up the clear cover take out the filter see Figure 3 and then clean the dust bin 2 Use a hair dryer with cold air to clean the filter see Figure 4 and dust clean with the dust brush see Figure 5 Figure 4 SS ind Figure 5 16 3 Reinstall the filter in the original position Tip The rubber cleaning head may fall off when you clean the dust bin Reinstall as shown below Rubber cleaning head gt Position the dustbin and rubber cleaning head as per Figure 1 Place one end of the cleaning head onto the clear cover of the dust bin make sure the rubber on the cleaning head is facing upwards and connect it with the dust bin Refer to picture 2 Push the cleaning head onto the clear cover by pressing it in with the palm of your hand The rubber cleaning head is a user replaceable spare part CLEANING THE MAIN BRUSH AND FLOOR BRUSH CLEAN BRUSHES AFTER EVERY USE TO MAINTAIN CLEANING PERFORMANCE AND PROLONG THE LIFE OF YOUR R Vac LF 2 Remove the dust bin see page 15 Open the locking bar by pressing the red latch and lift see Figure 1 Lift the main brush amp floo
16. installation 6 Maintenance 15 Charging methods 8 Trouble shooting 18 Functions 8 Customer Service 2 INSTRUCTIONS Congratulations on the purchase of your appliance Each unit is manufactured to ensure safety and reliability Before using the appliance for the first time please read the instruction booklet carefully and keep it for future reference Pass it on if you pass on the appliance When using electrical appliances basic safety precautions should always be followed Components Main Body x 1 Remote Control x 1 Charging Station x 1 Adapter x 1 Space Isolator x 1 User Manual x 1 Cleaning Brush x 1 Side Brush x 2 Filter x 1 0 Rechargeable Battery x 1 a ONO SS SY 6 _ TE NN 7 8 9 10 Structure Introduction SPOT spot cleaning AUTO automatic cleaning P ower indicator light Handle CHARGE charge Top cover Signal receiver Auto charging electrodes Wall detection sensors Floor brush removable Left wheel Dust bin Edge Drop detection sensors Main brush removable Battery cover removable SX A S Power snia Front wheel removable Side brush removable a Se ay Wy 8896600099 DC socket STS AOO LCE Right wheel Edge Drop detection sensors QUICK START GUIDE While the R Vac is a complex product we have committed to making the operation as user friendly as possible As a result of this you can have your
17. keep it pressed in Switch on the vacuum using the Power switch Release the internal synchronise button after the R Vac has emitted a series of beeps indicating it has synchronised NOTE If you fail to hear any beeping during synchronisation repeat the above process Positioning your Space Isolator The space isolator creates an invisible line which acts as a barrier that your vacuum cleaner will not pass Place the space isolator against the wall with the signal transmitter facing the area you would like to act as a barrier 13 CHARGING STATION LED indicator Infrared signal transmitting window Internal synchronise button on back of S charging station T MM es aS Charging electrode D DC socket JA The Charging Station is synchronised with your vacuum cleaner prior to purchase Automatic Charging 1 Position the charging station on a hard level surface against a wall 2 Ensure there are no obstacles 3 metres in front of the docking station or 0 5 metres on the right and left IMPORTANT Ensure the infrared signal transmitting window on the docking station is not covered otherwise the vacuum will not be able to find the charging station 3 Connect the output terminal of the adaptor with DC socket on the charging station Refer to Figure 2 14 4 Place your R Vac on the charging station with the silver auto charging electrodes on the front of the R Vac in contact with
18. may wish to select the slow setting to allow the R Vac to provide a more concentrated clean by passing over areas at a slower speed To vary your R Vac s speed press the SPEED button on the remote control Select fast or slow mode using the remote control NOTE The default speed setting of the vacuum is fast mode DIRECTION buttons Use the direction buttons to steer your R Vac to a desired location CAUTION Do not drive the R Vac in reverse towards drop offs or ledges The edge drop detection sensors only function when the vacuum is travelling in the forward direction SPACE ISOLATOR Signal transmitter Power indicator light Power switch Internal synchronise button The Space Isolator is synchronised with your vacuum cleaner prior to purchase 12 SPACE ISOLATOR BATTERY INSTALLATION amp REPLACEMENT 1 Open the cover on the base of the Space Isolator 2 Insert AA batteries not included with correct polarity 3 Replace the cover on the base of the Space Isolator IMPORTANT Remove the batteries if the Space Isolator will not be used for an extended period of time If your space isolator isn t operating correctly it may be necessary to re synchronise it with the R Vac using the following steps 1 Turn off the vacuum and switch on the Space Isolator the power indicator should illuminate amp begin to flash Using a paperclip or similar press in the internal synchronise button and
19. ner to pick up any of the following do not attempt to pick up liquid this cleaner is designed for dry substances only do not pick up items that may ignite spontaneously e g matches pieces of firelighter do not pick up anything burning or smouldering e g cigarette ends ashes or embers do not pick up spillage from toner cartridges the fine carbon particles may attached to the brushes and be spread throughout the cleaning area do not pick up cement or plaster dust these can combine with moisture in the air clog the filter and possibly cause the motor to overheat and burn out donot pick up sharp objects they may pierce the filter and damage the motor do not pick up biological waste you will eventually have to clean it off the filter and there is a possibility of viral particles passing through the filter and entering your air supply Do not use the cleaner for any purpose other than those described in these instructions 15 16 17 Use only the accessories supplied with the appliance Do not leave the appliance sitting in sunlight Prolonged exposure to UV rays may damage the plastic For added safety electrical appliances should be connected to a power outlet that is protected by a residual current device RCD also often referred to as a Safety Switch Your switchboard may already incorporate an RCD If unsure call an electrician for verification and fitting if necessary SAVE T
20. r brush up and away from the vacuum see Figure 2 amp 3 For the main brush use the cleaning brush to remove hair and dust If there is hair yarn and other twisted objects around the brushes carefully cut them using scissors and gently pull them off the brushes by hand Remove the circular rubber bearing on the end of each brush and remove any dust or hair build up Replace by pushing it back onto the brush end To re install the main brush amp floor brush into the vacuum align the drive ends of the brushes with the lugs on the opposite side of the locking tab place the brushes into their original position then close the locking tab until it clicks securely into place NOTE If the locking tab cannot be closed check that the circular rubber bearings have correctly located into their corresponding recesses 17 REMOVING REPLACING AND CLEANING UNDER THE SIDE BRUSH Using a screw driver release the screw in the main shaft of the side brush see Figure 4 2 Remove the side brush and clean the cavity with the dust cleaning brush 3 Place the side brush back into position and refit the screw k REMOVING REPLACING AND CLEANING THE FRONT WHEEL 1 Remove the entire front wheel assembly using a flat head screw driver from the front of the unit position the screw driver down and under the front wheel assembly Pop the wheel assembly out using the screw driver and clean the cavity 2 Remove the wheel using a
21. stopping to search for the docking station If the charging station is detected the vacuum will then make its way to the charging station dock automatically and begin to charge Once on charge the Power indicator will illuminate and flash REMOTE CONTROL amp PROGRAMMING Emission signal Curent time Pre set to select all or tum li Pre set time i fm gt _ off charging indicators cS 377 Pre set cleaning a Setting of current time T1Cx a ant a Charge Sten ON Power button Confirm Spot cleaning The Remote control is synchronised with your vacuum cleaner prior to purchase REMOTE CONTROL BATTERY INSTALLATION amp REPLACEMENT 1 Open the cover on the back of the Remote control 2 Insert AAA batteries not included with correct polarity as marked 3 Replace the cover on the back of the Remote control IMPORTANT Remove the batteries if the Remote Control will not be used for an extended period of time Ensure the batteries are installed in your remote control If your remote control isn t operating correctly it may be necessary to re synchronise it with the R Vac using the following steps Turn the Power switch to OFF 2 Press and hold the OK button on the remote control keep the button down until step 4 is confirmed Turn on the vacuum Release the OK button after the R Vac has emitted a series of beeps indicating it has synchronised NOTE If you f
22. ys turn off and disconnect from the power before cleaning Do not operate the appliance if the power adaptor of power cord is damaged in any way lf the power adaptor is damaged it must only be replaced by an approved power adaptor that is deemed suitable by the manufacturer Do not use a power adaptor that has not been recommended by the manufacturer as being suitable for charging this appliance This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety The appliance is not a toy Children should be supervised to ensure they do not play with this appliance The function of this appliance may disturb some animals pets All animals should be isolated from areas where this appliance is operating Clean with a damp cloth only Do not wet or spray liquids onto R Vac R Vac has edge sensors to prevent it from falling down steps or off platforms However barriers should be used to prevent access to drop offs where a danger to others may be presented in the case of a malfunction or misuse Clear the area to be cleaned of fragile items clothing power cords pull cords for curtains and blinds If the R Vac passes over and drags a power cord the object may topple of a cabinet or shelf ue not use the clea
Download Pdf Manuals
Related Search