Home

User Manual Nord Stage EX

1. THE ORGAN SWELL INPUT You can connect an expression pedal to the ORGAN SWELL input to control organ swell For the B3 organ the characteristic swell volume frequency response is faithfully reproduced If you want to control the entire Stage s volume with a pedal this can be set in the System Settings to apply to a pedal connected to the Organ Swell input See Swell Pedal Dest on page 68 for more information about this setting USING A ROTOR SPEED PEDAL You can use a pedal connected to the ROTOR SPEED input to switch between Slow and Fast rotor speed for the Rotary Speaker effect This pedal can work in hold or toggle mode which is set in the System Menu see page 66 Page 11 4 Getting Started About Instruments Nord Stage EX v6 x 4 GETTING STARTED ABOUT INSTRUMENTS When Instrument sections or Instruments are referred to in the manual this is a collective refer ence to the Organ Piano and Synth instruments which can be all be active within a Program ABOUT PROGRAMS A Program in Nord Stage EX basically contains all settings instruments and effects etc when the Program was saved A Program can consist of a single instrument or a combination of up to six in struments and two Extern sections which can be assigned
2. The horizontal dotted lines represent the cur rent drawbar level with sim out Percussion ine Key s Downl Key s Up Key s Down Key s Up The figure above shows the Percussion en The figure above shows the Percus velope in SOFT mode sion envelope in NORMAL mode Like on the original the Percussion is a single triggered non legato effect By single triggered we mean that the percussion is only present when you hit the keys when no other note is sounding In other words if you play a note or a chord and then add on more notes without releasing the previ ously pressed keys there will be no percussion effect in the new notes You have to release all keys to be able to play new notes with the percussion effect Also like on the original B3 in Normal Per cussion mode the sustain level is significantly lower than in Soft Percussion mode or with the Per cussion effect disabled VIBRATO VIBRATO CHORUS The original B3 chorus and vibrato scanner consists of a modulated delay line in rm combination with a rotating scanner For the Vibrato effect phase shift is applied v2 to the signal For the Chorus effect the phase modulated signal is added to the original signal A lot of time and effort have been spent in accurately recreating 4 the chorus and vibrato scanner effect Like on the original B3 Nord Stage EX offers three different types of choruses C1 C3 and three different
3. i a a INTRO DUG RE EE REA EO am EEIMMEIN FEATURE lt lt lt de 22 THE ORGAN a do Sb T HE PIANO Ras E EE UEM PES MERE MEME MM EE THE SYNTH Russa essi ssaa RES SRRaA RARE RR A nanara insania Table of contents Nord Stage EX v6 x ts THE err Ee sions cnt odetedsradsanducusnaneareeaubedssasesetetseusnsns 2 ABOUT THE EFFECTS ERREUR I RAS REM GE MES cease 49 THE PANEL EFFECT RIRRERERSFEREEAERESERSRERQSRASENEEARESEEE aa beans 50 THE ROTOR SECT zl 4M TETMEEIIIUUMSIILLUIUTEUMMBID 55 KEYBOARD ZONES bias ERR NA SCOPE CER EM NEN SGSRE 56 OCTAVE SHUE DUE DAR EFE M ER E ERR 58 DUAL PANEL SETUPS isxssaursnstsksabss eEMEAFYEESEEEKEFEEFIVEEFSESESRTERFCCFRSCRENSEY FEES 58 ABOUT MORPH ASSIGN 60 USING MORPH AN EXAMPLE ssssssssuassuasuuanssassassuasusasuuasnasunaseunaouuasus 60 MORPH ASSIGNABLE PARAMETERS scsssssnussussuassua
4. Ctrl Pedal Type Different brands of control pedals have different specifications resistance offset and linearity To simplify setup and to optimize the response of the pedal for the Nord Stage the most common pedal makes are preconfigured and you simply select the type of pedal you connect Roland Yamaha and Fatar are linear control pedals with different scaling and offset Ernie Ball pedals ErnieB are marketed as volume pedals with a logarithmic response but the response is rescaled internally in the Nord Stage to make them work nicely as control pedals They may need a Y cable stereo plug gt 2 mono plugs to work with the Nord Stage Roland Default Yamaha Ernie B Fatar Control Pedal Use as Swell You can use a control pedal to control organ swell If you wish to do so set this to Yes Note that even if this is enabled and you connect a pedal to the Organ Swell input this setting will be overridden and you will be able to use both pedals separately No Default Yes Page 67 11 System functions Sound Menu Nord Stage EX v6 x Swell Pedal Type This setting configure the Swell Pedal See Ctrl Pedal Type above for details Roland Default Yamaha Ernie B Fatar Swell Pedal Dest This setting configure the Swell Pedal destination Set this to Organ if only the Organ section should be controlled or to All if the volume of all sections should be controlled Organ
5. 2 octaves you can use the OCTAVE SHIFT buttons to transpose the piano up or down to select which 2 octave range of the available 9 octaves is to play in this Zone Thus you can always access the whole note range of any instrument within any set Zone range KB Zone Y Y Down 2 octaves Up 1 octave B Down 3 octaves Up 2 octaves In the illustration above a piano has been assigned to play in a KB Zone stretching from C4 to C6 Without Octave Shift the actual note range that will be played will be the same as the set Zone The dotted lines show which note range will be played in the set Zone when using Octave Shift In this case you can transpose the piano up or down two octaves so you can play any two octave note range from the selected Zone No matter what a Zone range is set to you can always reach the entire octave range of any instrument DUAL PANEL SETUPS If you press both PANEL A and PANEL B buttons so that they both light up this means that both Pan els are active One of the Panels is always edit active i e it is the panel settings for either Panel A or Panel B that is currently shown and can be edited The active Panel is indicated by a blinking PANEL LED To show edit the settings for the other Panel press the corresponding PANEL button so that it starts blinking To disable one of the panels hold the PANEL button for the panel you want to keep active and press briefly th
6. For a full list of which parameters correspond to which Controller number see the MIDI implementation chapter on page 90 KEYBOARD VELOCITY Nord Stage EX can transmit and receive Keyboard Velocity messages Organ sounds will always be played back at nominal level regardless of incoming MIDI Velocity data Release velocity is trans mitted but ignored on MIDI In AFTERTOUCH The Nord Stage EX keyboard can transmit A ftertouch messages sometimes called channel pressure The player can apply more pressure on a key while it is down and this will generate a signal that can be used to control parameters see About Aftertouch on page 62 Page 86 Nord Stage EX v6 x 14 MIDI functions Using Nord Stage EX with a sequencer PROGRAM GHANGE On the MIDI Menu see page 68 you can select if the Nord Stage should send and or receive Pro gram Change messages When you select a Program a Program Change message is transmitted via MIDI on the active Panel MIDI Channel If a Program Change message is received on any of the Panel A B MIDI Channels Nord Stage EX will change Program accordingly Note A program change on either of the two Panel MIDI Channels will affect both Panels The 126 Program locations send and respond to MIDI Program Change values 0 125 Live buffers 1 2 correspond to MIDI Program Change 126 127 MIDI SvsEx SYSTEM EXCLUSIVE Single Programs Synth sounds or all Programs all sounds can be transmitted and receive
7. GREATING A SPLIT Creating a split so that different instruments are assigned to different keyboard zones is very easy to set up Proceed as follows 1 Activate two instrument sections e g an organ sound and a piano sound by pressing the KB ZONE SELECT buttons in each corresponding section so that the KB ZONE LEDs Lo Up Hi light up If you now play the keyboard you should hear both instruments layered 2 Press the KB ZONES 2 button This splits the keyboard into two Zones an upper and a lower The split point is indicated by a green LED above the corresponding key on the keyboard KB ZONES PANEL A PANEL B C 2 D 3 t DUAL KB SET LO SETHI SPLIT SPLIT Page 56 Nord Stage EX v6 x 6 Keyboard Zones and Dual Panel setups Keyboard Zones 3 Toassign the Organ instrument section to play on the lower Keyboard Zone only hold down SHIFT and then press the KB ZONE SELECT button for the Organ section until only the LO KB ZONE indicator is lit 4 To assign the Piano instrument to play on the upper half of the keyboard hold down SHIFT and press the KB ZONE SELECT button for the Piano 7 section until both the UP HI KB ZONE indicators are lit DE KB ZONE SELECT Now the lower half of the keyboard will play the organ sound and the upper half will play the piano You can also step through the different Keyboard Zone assignments by double clicking the KB ZONE SELECT button This is convenient when
8. STORING A PROGRAM You can store a Program in two ways with the old name or with a new name To store a Program without changing its name proceed as follows 1 Press the STORE button once The STORE button and the cur rently selected PROGRAM button indicator starts blinking and the DISPLAY will read Store to X X the current Page and Program number plus the Program name 2 Next step is to select a Page Program location to store the edited Program in You can use the PAGE buttons to select a Program Page 1 21 and the PROGRAM 1 6 buttons to select a Pro gram number on the selected Page or the Live 1 or 2 memories Alternatively you can use the VALUE DIAL to scroll through all Programs on all Program Pages To cancel the operation press EXIT SHIFT From here you can opt to name the program before finally storing it see Naming a Program below 3 Press STORE again to store your Program The Display now reads Program Stored for a short duration Page 20 Nord Stage EX v6 x 5 The Program section Storing Programs NAMING A PROGRAM To name a program proceed as follows 1 Hold down SHIFT and press the STORE AS button once The STORE button indicator starts blinking and the DISPLAY will read Set Name 2 Now use one of the following methods to name your Program You can move the cursor position left or right in the DISPLAY by using the PAGE buttons When the cursor is at
9. Slow Organ Percussion 25 Soft Organ Percussion 25 Sound Page 68 Split Organ 29 Splits Creating 56 Stop Rotary Speaker 55 Store button 18 Storing Programs 20 Storing Synth Patches 48 Sustain pedal Connecting 11 Sustain Pedal Polarity 67 Swell Organ 29 Swell Pedal Type 68 Sync Oscillator 38 Synth Amp Envelope 43 Digital wavetable 41 EQ 47 FM 39 Mod Envelope 41 Osc section 35 Sound Init 48 Sound Select section 47 Vibrato 47 Synth Output 67 Synth Sound bank dumps 77 Page 97 Index Synth Vibrato Amount 68 Rate 68 System menu 66 T Tap Tempo Delay Effect 53 Timbre control Synth 35 Transpose 66 Tremolo modulation 51 Uu Unison Synth 47 USB for downloading Piano instruments 72 V1 V3 Organ Vibrato 26 Value Dial 17 Velocity Sensitivity Piano Dynamics Piano 33 Vibrato F Type organ 28 Vibrato organ 26 Vibrato Synth 47 V Type Organ Vox Continental 27 Ww Wurlitzer 200A internal speaker 54 Y Yamaha control pedals 67 Page 98 Nord Stage EX v6 x
10. 24 Organ Vibrato Enable 25 Organ Percussion Harmonic 26 Organ Percussion Speed 27 Organ Percussion Level 28 Organ PStick Enable 29 Piano Clav Filter 1 30 Piano Clav Filter 2 31 Piano Dynamics 33 Synth Glide Rate 34 Synth Glide Auto 35 Synth Voice Mode 36 Synth Unison 37 Synth Vibrato Mode 38 Synth Mod Envelope Attack 39 Synth Mod Envelope Decay 40 Synth Mod Envelope Mode 41 Synth Mod Envelope Velocity 42 Nord Stage EX v6 x 15 MIDI implementation MIDI Controller list Nord Stage Parameter MIDI Controller Synth Oscillator Mode 43 Synth Oscillator Wave 44 Synth Oscillator Timbre 45 Synth Oscillator Timbre Amount 46 Synth Oscillator TimbreVelocity 47 Synth Filter Frequency 48 Synth Filter Resonance 49 Synth Filter Amount 50 Synth Filter Velocity 51 Synth Filter KBT Keyboard tracking 52 Synth Filter Type 53 Synth Amp Envelope Attack 54 Synth Amp Envelope Decay 55 Synth Amp Envelope Mode 56 Synth Amp Envelope Velocity 57 Synth EQ Gain Lo 58 Synth EQ Gain Hi 59 Effect 1 Type 60 Effect 1 Source 61 Effect 1 Amount 62 Effect 1 Rate 63 Effect 1 Enable 69 Effect 2 Type 70 Effect 2 Source 71 Effect 2 Amount 72 Effect 2 Rate 73 Effect 2 Enable 74 Delay Destination 75 Delay Amount 76 Delay Rate 77 Delay Feedback 78 Delay Ping Pong on off 79 Delay Enable 80 AmpSim 81 AmpSim Destination 82 AmpSim Drive 83 AmpS
11. 6 The Instruments The Synth section 12 DB The 12 dB octave slope leaves more harmonics than the 24dB variation discussed above This type of filter has been used in various early Oberheim synthesizers and others A 12 dB filter is also known as a 2 pole filter KB TRACK The reason for having the Keyboard Track switch is related to basic acoustics If you raise the pitch of a waveform the harmonics naturally raise in frequency If the cutoff frequency is constant the sound will be perceived as getting muddier the higher up the keyboard you play To avoid this ef fect use KB Track KB Track keyboard tracking has three modes FULL 2 3 and 1 3 which is set with the KB TRACK button With KB T turned off both LEDs off the filter frequency setting is constant regard less of where on the keyboard you play When Keyboard Track is activated the filter frequency set ting will be higher for higher notes as indicated in the illustration below At Full tracking both LEDs on the filter frequency tracks the keyboard 100 if you turn up the Resonance parameter to full so that the filter self oscillates and produces a pitch Filter Frequency will track to 12 notes oc tave If 2 3 or 1 3 is selected the filter frequency keyboard relationship is more subtle 1 e the filter frequency will increase less with higher notes 66 and 33 respectively The figure shows how the Frequencyl value changes according to whe
12. Attack etc In this the Mod Envelope acts as an LFO with shapable waveform The Mod Envelope can control the Filter Frequency and Timbre parameters The wp amount of modulation is set with the FREQ CONTROL and TIMBRE CONTROL knobs ATTACK Attack sets the time it should take for the envelope to reach maximum level after you have pressed a key Turn the ATTACK knob clockwise to increase Attack time Page 41 6 The Instruments The Synth section Nord Stage EX v6 x RELEASE DEGAY When the attack phase is over the envelope drops back to zero level Use the REL DECAY knob to set the time this should take ENV VEL If you press SHIFT and turn the ATTACK knob so that the ENV VEL indicator lights up the Mod En velope will be scaled with the keyboard velocity i e how hard or soft you play This is normally used to make higher velocity louder notes produce brighter sounds because of higher modulation of the filter or the Timbre which is how most acoustic instruments behave MODE Hold down SHIFT and turn the REL DECAY knob to select Envelope Mode The LEDs below the knob will show the selected mode The Attack Decay and Attack Release modes are illustrated below Level In Attack Decay mode the Mod Envelope outputs a control signal that rises to maxi mum amount at the set Attack time and then immediately falls back to zero at the set De cay time gt lt gt Attack Dec
13. Default All Memory Protect This is set to On when Nord Stage EX leaves the factory meaning that you cannot save any changes to Programs or Synth Sounds Set this to Off if you wish to store your own Programs System settings and the two Live buffers are not protected by this set ting On default Off Factory Reset This resets all system settings and restores the origi nal Live buffers Hold the flashing STORE a few sec onds to perform the reset The display will take a few seconds Stored programs are not affected by this action except the live buffers SOUND MENU Press SHIFT SOUND to access the Sound menu Use the PAGE buttons to navigate between the various menu items on the Sound menu Hold a PAGE button to scroll quickly The VALUE DIAL is used to change settings When you are done press EXIT SHIFT briefly to exit the menu Note The settings on the Sound menu are not saved with a Program The following items can be found on the Sound menu Function Description Range Values Synth Vibrato Rate This determines the rate of the Synth Vibrato 4 00 8 00 Hz Default 6 00 Hz Synth Dly Vibrato Amount This determines the amount of Synth Vibrato when any of the vibrato delay modes are used 0 50 cent Default value is 25 cent Organ Key Click This sets the amount of Key Click for B3 organ 1 10 Default value is 5 Level
14. Dual Panel setups on page 56 KB ZONES 2 JE SETLO SET HI SPLIT SPLIT MORPH ASSIGN BUTTONS MORPH ASSIGN WHEEL 9 ATOUCH CTRLPED ec uc ne m CLEAR MORPH ooo This section allows you to assign panel parameter s to be controlled using the Mod wheel a control pedal or keyboard aftertouch Multiple parameters can be Morph assigned so that when you for ex ample move the Mod wheel it will change the drawbars settings for the organ and the volume of the piano section simultaneously See The Morph Assign feature on page 60 PANEL A B BUTTONS 9 PANELA 9 PANEL B e DUMP ONE DUAL KB For each Program you have two independent Panels A and B where each Panel contains independent instances and settings of the three instrument sections and effects If you activate both Panels you can use two instruments of the same type at the same time e g two Piano instruments or a Split Organ setup see About Split Organ Setups on page 29 This is done by simultaneously pressing both PANEL A and B buttons When both panels are active you have access to six instrument sections and eight effects sections Effect 1 amp 2 Delay and AmpSim EQ x2 One of the PANEL A amp B buttons will then blink to indicate edit focus 1 e which of the two Panel s settings that are currently shown and can be tweaked To switch edit focus to the other Panel press the corresponding PANEL button Page 18 Nord Stage EX v6 x 5
15. NORD SOUND MANAGER REFERENCE TOOLBAR A M Ra o B Organize Dual View Auto Select SoundUp Sound Down Rename Delete BankUp Bank Down Backup Restore ORGANIZE When this option is active the lists will show all the available locations in the selected partition bank and not only the occupied ones This will for instance make it easier to drag a file to a specific free location in the middle of the list If this is inactive only the occupied locations will be shown DUAL VIEW When this option is checked the window will be divided in two lists The two lists makes it easy to move programs from one location to another You can make the lists show separate banks with the dropdowns Rearranging programs is simply a matter of drag and drop Drag a program from one bank list to another bank list in either direction AUTO SELECT With this function active scrolling through the program list with the computer keyboard arrow keys will automatically select the programs in the Nord Stage EX SOUND UP Use this function to upload one or several sounds from the Nord Stage to the computer hard drive SOUND DOWN Use this function to download one or several sounds from the computer hard drive to the next avail able location in the selected partition RENAME Allows you to rename a sound 16 characters can be used and the supported characters are a z A Z 0 9 and the hyphen Any other characters will not be displayed in the Sound Man
16. Nord Stage EX when you browse through the Programs in the Manager list with the computer keyboard arrow keys HELP E About ABOUT Brings up the About box with a information regarding the version of the Nord Sound Manager You will also see a list of compatible instruments and OS versions Page 83 13 Nord Sound Manager Tabs Nord Stage EX v6 x TABS Piano Program Synth Bank All 126sounds PIANO PROGRAM SYNTH Use the tabs to select the desired partition Type Ctrl Tab on the computer keyboard to cycle between the three tabs The drop down menu is used to select the desired bank within a partition The content of the partition will be presented in the list SEARCH Box Enter a phrase to quickly present any samples or programs that contains the characters Press Clear to clear the filtering and show all entries again Loc LOCATION The banks are organized in locations the amount of locations varies for the different bank types NAME The name of the item SIZE Shows the file size of the Piano samples This may be useful if you need to know how much space e g a particular piano occupies in the Piano partition This unit is not shown in the Program or Synth lists VER VERSION NUMBER Version number of the actual format of the pianos programs or synth patches Please note that pianos in the npno format 4 x or 5 x programs or synth patches cannot be used with a Stage that has an old
17. Sending Program dumps on page 88 Off Send Receive Send amp Receive Default Panel A Panel B One Default All Dump Synth Sound Here you can perform a separate MIDI SysEx dump of just the Synth memory settings See Sending Synth Sound bank dumps on page 89 Slot A B Synth Pad Bass All Default Instrument SysEx ID Most instruments have a unique Instrument ID If more than one of the same instruments are con nected in a MIDI network this ensures that no instru ment will receive SysEx dumps not intended for it 1 16 All Default Page 69 11 System functions Extern menu EXTERN MENLI Nord Stage EX v6 x Press SHIFT EXTERN to access the Extern menu where you can find settings and functions relating to the Extern section see Extern section on page 63 Use the PAGE buttons to navigate between the various menu items on the menu The VALUE DIAL is used to change settings When you are done press EXIT SHIFT briefly to exit the menu Most items on the Extern menu have separate entries for Panel A and B Most settings from the Ex tern menu are saved with a Program The only exceptions are the Extern MIDI Channel if Ex tern MIDI Mode is set to Global and Send on Load The following items can be found on the Extern menu Function Description Range Values Extern MIDI The Extern MIDI Channel can be determined in two different Global Pro
18. Stage EX v6 x DOWNLOAD A NEW PIANO 1 Using drag and drop Open the folder on the computer hard drive where the new piano is located 2 Make sure that the Sound Manager window and the folder are visible on the screen Mame ConcertGrandi StwD Amb 4 4 npno ConcertGrandi Stw D Close 4 4 npno Wi ConcertGrand1 XL StwD Amb 4 4 npno TE concertGrand1 XL Stw D Clos 4 4 npno gag E Piano 1 Mk I Deep 4 4 npno Bank Grand 2 sounds Loc StudioGrand 2 XL YaC Clos 4 4 1 2 3 Grand YaC7 Close 4 2 3 Drag the new piano to the white area or to an empty location in the Sound Manager piano list 4 The Clean Deleted Space process will start to prepare the memory and then the new piano will be downloaded to the Stage If there isn t enough free space a message will appear in the lower left text area in the Sou The pianos are categorized and can only be added to the correct bank electric pianos can not be added to the grand bank the grand s cannot be dropped in the clavinet bank etc Tip If the Organize option is active in the View menu you can drop a sound on any free location in the bank If this function 1s not active the new sound will be automatically placed at the first free location in the bank The various locations are selected using the Type selector on the Nord Stage 1 Using the Toolbar or menu command Click on the Sound Down icon in the toolbar The sam
19. can be described as constant rate which means that the greater the distance between two subse quent notes the longer the glide time Turn the GLIDE knob clockwise to increase the glide rate Page 46 Nord Stage EX v6 x 6 The Instruments The Synth section AUTO Press SHIFT and turn the GLIDE knob to select Auto Glide mode the AUTO LED is lit This means that glide is active only when you play legato you press a new key before you release the previous key UNISON The oscillator section has a number of hidden oscillators The number of extra oscillators varies with the algorithms but is usually between three and eight When you activate Unison these slightly detuned voices are gradually added to the basic sound for those classic synth chorus effects Note that Unison doesn t reduce the polyphony You adjust the number of extra oscillators and the detune amount among the voices with the UNISON knob The left half of the UNISON knob range controls a classical two voice detune effect As a special case in the Sawtooth detuned oscillator mode the left half of the UNISON knob range controls the detuning between the two main oscillators The right half of the UNISON knob range introduces a thicker multi voice detune which can be very powerful VIBRATO Vibrato modulates the pitch of the oscillators to produce natural vibrato effects VIBRATO DLY3 There are three basic methods you can use to c
20. independently for each program When Glo bal is selected the output routings will be the same for all programs and the global settings will override the routings stored with each program Organ Audio This allows you to set which channel output pairs or 1 amp 2 Default 3 amp 4 Output mono output to use for the Organ section Note that 3 4 you cannot have different routings for Organ A and B If the Audio Routing Mode see above is Program this setting will be saved with the program Piano Audio A B This allows you to set which channel output pairs 1 amp 2 Default 3 amp 4 Output mono output to use for the Piano A and B sections 9 4 Use the Panel A amp B buttons to access the settings for each panel If the Audio Routing Mode see above is set to Program these settings will be saved with the program Page 66 Nord Stage EX v6 x 11 System functions System menu Synth Audio A B Output This allows you to set which channel output pairs or mono output to use for the Synth A and B sec tion Use the Panel A amp B buttons to access the set tings for each panel If the Audio Routing Mode see above is set to Program these settings will be saved with the program 1 amp 2 Default 3 amp 4 3 4 Organ Keyboard Trig Mode This allows you to change how the Nord Stage EX keyboard triggers Organ sounds When Fast High i
21. modulation effects The following effects are available RM RING MODULATION Ring Modulation is a type of modulation where two signals are multiplied with each other The result is an inharmonic bell like sound Herbie Hancock used this effect a lot in the 70s In the Nord Stage EX the instrument signal is multiplied with an addi tional sinewave ORG PIANO SYNT When RM is selected you set the sinewave pitch with the RATE TEMPO knob and the amount of ring modulation with the AMOUNT knob This effect is mono in out on D SOURCE TREM TREMOLO Tremolo is basically volume modulation that continuously varies the output signal volume Tremolo is acommonly used modulation especially for Wurlitzer electric pianos The Tremelo effect is stereo in out Amplitude The filled curve indicates maximum AMOUNT value and the dashed curves indicate lower AMOUNT values At zero AMOUNT value the output level is constantly at maximum level time gt Use the RATE TEMPO and AMOUNT knobs to control the Tremolo rate and depth Note that the out put volume is at maximum level at zero AMOUNT setting A PAN PAN The A Pan is an auto panning modulation that smoothly pans the signal between the Left and Right outputs Modulation The filled curve indicates maximum AMOUNT value and the time dashed curves indicate lower AMOUNT values The signal smoothly pans between the Left and Right outputs as indicat You contro
22. settings The 126 Pro gram locations send and respond to Program Change values 0 125 while Live buffers 1 2 corre spond to Program Change 126 127 Make sure the Program Change is sent on either of the Panel A B MIDI channels Page 87 14 MIDI functions Program Controller and Synth Sound dumps Nord Stage EX v6 x If you want to record a Program Change message activate recording in the sequencer and simply load the program once on the Nord Stage CONTROLLERS When you record knob movements and button presses make sure that sequencer echoes the changes back on the correct MIDI Channel or your changes won t have any effect SOME NOTES ABOUT CONTROLLERS AND CHASING Consider a situation where you record a Controller message e g a Drawbar opening in the middle of your sequencer song Then you rewind the sequencer to a position before the recorded Drawbar opening The problem is that the Nord Stage s Drawbar will remain opened although it really should be as it was before you recorded the opening To solve such problems several sequencers include a function called Controller Chasing which keeps track of Controller changes and tries to adjust the settings on the instrument according to the current position in the sequencer song However in our example this wouldn t help much because the Drawbar opening was the first Con troller message recorded in the song The sequencer has no information about the Dr
23. the original factory programs later you can download them at http www nordkeyboards com and transfer them to your Nord Stage EX as MIDI SysEx files or use the Nord Sound Manager to reload them To indicate that a Program has been edited changed from the stored version an asterisk is shown to the right of the Program number in the DISPLAY REVERTING TO THE ORIGINAL PROGRAM If you have edited a Program and want to revert to the stored original just press the corresponding PROGRAM button again STORING AND NAMING PROGRAMS How to store and name Programs is described in a separate chapter see The Program section on page 16 ACTIVATING INSTRUMENT SECTIONS There are three main instrument sections in Nord Stage EX the Organ section the Piano section and the Synth section You can activate deactivate instrument PAAK sections in the following ways KB ZONE SELECT Pressing the KB ZONE SELECT ON OFF button for an Instrument section so that one or more of the LEDs lights up will activate the corresponding instrument If all LEDs are lit the instrument will play across the whole range of the keyboard Any other active instrument s will in this case be layered with the instrument you just activated Pressing the KB ZONE SELECT button for an active Instrument section so that the LEDs go dark will turn off the corresponding section For information on how to use splits see the chapter Keyboard Zones and Dual P
24. to one ore more Keyboard Zones for split and layered sounds Programs also contains settings for both Panel A and B see About Panel A amp B on page 14 For more details about the Program memory architecture see What is a Program on page 19 SELECTING PROGRAMS The Program memory in Nord Stage EX consists of 21 Program Pages with each Page holding 6 Pro grams for a total of 126 Programs All Programs can be edited and replaced at any time To select a Program for playing editing proceed as follows 1 Select a Page 1 21 by pressing the PAGE buttons in the Program CURSOR section Hold a PAGE to scroll quickly through the Program Pages PAGE 2 Select a Program on the current Page by pressing one of the six PRO CD GRAM buttons 1 to 6 PROG PROG DEL INS PROGRAM JE 2 D 3 c NC NC NC SYSTEM SOUND MIDI EXTERN LIVE 1 LIVE2 E ES You can also use the VALUE DIAL to the right of the Dis PLAY to select Programs By turning the knob you can con tinuously scroll between all Programs on all Pages PENDING PROG CHANGE Page 12 Nord Stage EX v6 x 4 Getting Started Activating instrument sections EDITING A PROGRAM Actually how to change a programmed sound can be described in one sentence tweak the knobs and press the buttons It is as simple as that Don t be afraid to edit and overwrite the factory Pro grams If you want to restore any of
25. ume adjustment was set to close E Piano Electric Piano Mk II Stage Piano built in April 1981 and adjusted to shallow timbre The volume adjustment is set to close E Piano Electric Piano Bright Tines Custom Mod With the invaluable help of one of the planets most acclaimed electric piano technicians we have prepared one of our magnificent 1975 mk Suitcase with a special selection of hard hammer tips in certain ranges It is adjusted with close miking and set to ideal timbre in order not to loose the fundamental and the bottom end The preparation also involved adjustment of the striking line and re voicing of the harp in order to get that bell sound Wurl Wurlitzer 200A electric piano Clav Hps A D A sampled Hohner Clavinet D6 There are 4 Types selectable with different pick up variations See Pick up Type on page 33 In addition all possible filter combinations of the original Clavinet D6 can be recreated in the Clav EQ section See Clav EQ on page 33 Clav Hps Clav Hps A double stringed Italian harpsichord set to the Long string only registration A double stringed Italian harpsichord set to the Lute registration More information on the included factory pianos and other pianos in the Nord Piano Library can be found on the www nordkeyboards com website DLAv EUG PiIANO UNISON DETUNE The Unison Detune feature allows you to detune two pianos if they ar
26. until you release the button THE SHIFT BUTTON Many buttons and knobs have a second function printed in darker text just below the button or knob You access these additional functions and parameters by holding SHIFT while pressing a button or turning a knob The SHIFT button is also an EXIT button used for example to exit menus and store operations Page 9 3 Connections Nord Stage EX rear panel Nord Stage EX v6 x 3 CONNECTIONS NORD STAGE EX REAR PANEL SWELL CONTROL MIDI OUT MIDI IN USB ROTOR SPEED SUSTAIN CH4 OUT CH3OUT CH20UT CH1 OUT HEADPHONES EDAL PEDAL 00001 al C o Q O cooooooo 9 00000000 Sooo Bi 00000000 ooooo aoe P OOOOOOOO ooo OOOOOOOO MIDI equipment sequencer MIDI T T 4 T T d L keyboard etc Oi O t OO AUDIO CONNECTIONS Make all audio connections before turning on your power amplifier All signal cables used with the Nord Stage EX must be shielded The four audio outputs CH OUT 1 4 are line level and unbalanced f you wish to connect the Nord Stage EX in stereo to your audio equipment you should use CH1 OUT in pair with CH2 OUT You can also route individual instruments to CH OUTPUTS 3 amp 4 either in stereo or as two mono
27. would be as accessible and easy to use as the functions and parameters v for the built in instruments That s what you get in the Extern section PARAMETER The Extern in most cases behaves like the internal instruments For example it is 2 i xa enabled and assigned a keyboard zone in the same way It has a multi purpose Pa or rameter knob which is used to send MIDI Volume Program Change and Contin aan uous Controller messages You select the current Parameter focus with the ED PARAMETER SELECT button Detailed settings for MIDI Channel Program Jud Change and Continuous Controllers among other things are accessed through the Extern Menu see page 70 PARAMETER SELECT VOLUME PROG CHANGE SETTING UP 1 Connect a MIDI cable from Nord Stage 5 MIDI Out to the MIDI In on external device 2 Press SHIFT and the EXTERN button to access the Extern menu 3 Use The PAGE buttons to access the Extern MIDI Channel page 4 Use the VALUE DIAL to select the MIDI channel 1 16 you would like to transmit over Use the PANEL A and B buttons to access the channel setting for each panel Press the EXIT SHIFT but ton briefly to exit the menu 5 Set the external instrument to receive on the same MIDI channel USING THE EXTERN SECTION ACTIVATING Before Extern MIDI is sent out from Nord Stage EX you have to activate the Extern section This is done by pressing the ON button under the PARAMETE
28. you have only one hand free and cannot reach the SHIFT button To activate all three Keyboard Zones press the KB ZONES 3 button Now the keyboard is split into three Zones Now if you press the SHIFT KB ZONE SELECT button or double click the KB ZONE SELECT button for an Instrument section you can step through the following options LO UP HI indicators lit the corresponding instrument will play across all Zones 1 3 LO indicator lit the corresponding instrument will play across Zone 1 only LO UP indicators lit the corresponding instrument will play across Zones 1 2 UP indicator lit the corresponding instrument will play across Zone 2 only UP HI indicators lit the corresponding instrument will play across Zones 2 3 HI indicator lit the corresponding instrument will play across Zone 3 only No indicator lit the instrument will not play at all from the internal keyboard but only from MIDI This alternative is only available when an instrument has been assigned an individual MIDI channel see MIDI menu on page 68 SETTING SPLIT POINTS TO CHANGE ZONE RANGES You can set the split points for Zone 2 and 3 in the following way Press SHIFT and SET Lo SPLIT button repeatedly As you can see the green split indicator above the keyboard alternates between the available split points There are split points at C and F in each octave You use the same procedure but with SET HI SPLIT button to set the split
29. 1 2 Tip The one operator algorithm can be used to produce a perfect sine wave if the TIMBRE knob feedback is set to zero DIGITAL WAVEFORM CATEGORY This category features 77 different digital waveforms with various tonal characteristics The wave forms have been carefully designed and selected to provide rich and interesting timbres with a great variety for those exquisite sounds that could not be produced with the other algorithms Advanced wavetable synthesis techniques have been used to reproduce the waveforms perfectly over the whole keyboard range Some waveforms have a number of peaks high up in the spectrum making them suitable for voice like sounds e g 3 7 8 12 while others are combinations of several overlapping spectra e g 5 6 18 19 Yet others are extremely bright with a fundamental that is softer than the many harmonics e g 21 23 26 27 Using these waveforms with the different filters and the Synth EQ you should be able to create a wide variety of timbres The TIMBRE knob does not have any effect in the Digital Wavetable category ENVELOPE The Modulation Envelope is a simple two stage envelope used to modulate the tone colour over the duration of a note e g create a bright attack by modulating the filter in the start of the note The Mod Envelope has three modes Attack Decay ignoring key release 05 Attack full sustain Release Repeat mode Attack Decay Attack Decay
30. 11 System functions System menu Nord Stage EX v6 x 1 SYSTEM FUNCTIONS The System functions are divided into four menus System Sound MIDI and Extern Press SHIFT and the corresponding button in the Program section to access the desired menu PROGRAM ED i i I5 SYSTEM SOUND MIDI EXTERN To leave a menu at any time press the ExIT SHIFT button briefly All changes you make to the system functions are automatically stored in Nord Stage EX except the Local On Off setting which is always set to Local On at power on SYSTEM MENU Press SHIFT SYSTEM to enter the System menu Use the PAGE buttons to navigate between the different pages Push a PAGE button once to step through the menu or hold the button to scroll quick ly Use the VALUE DIAL to change the settings When you are done press EXIT SHIFT briefly to exit the menu The following items can be found on the System menu Function Description Range Values Transpose Transpose allows you transpose the pitch of instru 6 semitones in steps of ments up or down in semitone steps 1 semitone Default value is 0 no transpose Fine Tune Fine Tune can be used to adjust the pitch of instru 50 Cents half a semi ments in finer increments tone Default value is 0 no fine tune Audio Routing The output routing of the instruments in the Nord Global Default Program Mode Stage can be determined in two different ways glo bally or
31. 119 Default is 2 Extern MIDI A B Send Wheel To avoid transmitting Modulation Wheel messages make sure this option is set to No Yes Default No Extern MIDI A B Send A Touch To avoid transmitting After Touch messages make sure this option is set to No Yes Default No Extern MIDI A B Send CtrlPed To avoid transmitting Expression Pedal messages make sure this option is set to No Yes Default No Extern MIDI A B Vel Curve Use this setting to adjust the velocity response curves in the Extern section Norm Default Soft Hard Extern MIDI Send on Load To avoid transmitting Program Change Volume or MIDI CC mes sages when you load a Program in Nord Stage EX make sure Send On Load is set to Off on the Extern menu No Default Yes Page 70 Nord Stage EX v6 x 12 Factory Presets and OS Internal memory 1 2 FACTORY PRESETS AND OS INTERNAL MEMORY The Operating System Programs and Piano samples in Nord Stage EX are stored in a so called Flash memory A Flash memory keeps the data also when the power is shut off Another big advantage is that you can replace data in the Flash memory at any time This means that you will be able to down load OS upgrades and Programs to your Nord Stage EX from a computer or sequencer without need ing to replace or add any new hardware Nord Stage EX also features a USB port for quick and easy download of new Piano instr
32. 8 KB TRACK 9 9 10 VELOCITY RESONANCE MOD ENV The filter is together with the oscillators the most important sound shaping tool in a synthesizer The filter section in Nord Stage EX comprises a lowpass filter with either a 12dB or 24 dB slope with selectable keyboard tracking The filter has adjustable resonance and is self oscillating at high reso nance settings The filter cut off frequency can be modulated by velocity or by the Mod Envelope FILTER FREQUENCY CUTOFF With the FREQ knob you set the cutoff frequency Simply put if you turn the FREQ knob clockwise the high frequency content in the signal will increase This parameter can be Morph controlled When you open a low pass filter the high fre quency content increases in the output signal Amplitude e LP FILTER In the Nord Stage EX you can select between 12 dB octave and 24 dB octave 4 pole slopes for the low pass filter Press SHIFT and the 4 POLE button to switch type The 4 POLE LED shows which filter mode is selected eee The figure shows the filter with 24 dB and 12 dB slopes Cutoff frequency 12 dB octave Frequency 24 DB 4 PaLE This is the classic synth filter slope used in the Minimoog and Prophet 5 among others It cuts out frequencies rather drastically 24 dB per octave A 24 dB filter is also known as a 4 pole filter Page 44 Nord Stage EX v6 x
33. B3 sounds see Key click control on page 26 Rotor Acc The acceleration rate of the Rotor effect i e howlong Slow Mid Default Fast it takes for the Rotor to speed up or slow down Delay Mode This sets if the delay should change the pitch on Analog Default Normal sounding repeats if the Rate Tempo knob is adjusted or not When set to Normal the pitch does not change MIDI MENU Press SHIFT MIDI to access the MIDI menu Use the PAGE buttons to navigate between the various menu items on the MIDI menu Hold a Page button to scroll quickly The VALUE DIAL is used to change settings the Panel buttons to switch between A and B where applicable When you are done press EXIT SHIFT briefly to exit the menu Page 68 Nord Stage EX v6 x 11 System functions MIDI menu The following items can be found on the MIDI menu Function Description Range Values MIDI Control Here you set whether the Nord Stage EX keyboard On Default Off Local and front panel controls should control internal Pro grams or only send MIDI Local On is the normal play mode In Local Off mode the front panel and keyboard actions are transmitted via MIDI only and do not control the internal sound s directly MIDI Panel A B This sets the MIDI channel for Panel A B 1 16 Off Default A ch 1 Channel Default B ch 2 MIDI Organ A B This sets the MIDI channel for the Organ section A B 1 16 Off Default off Channel If a ch
34. DI channel a lit LED indicates it is activated THE PARAMETER SECTION The Parameter section comprises the three buttons in the Parameter Select section and the PARAMETER rotary encoder at the top Simply put you select a parameter and vary the value of the selected parameter with the rotary knob The PARAMETER rotary encoder can also be Morph control led see page 60 The following parameters can be set using the Parameter Select buttons VOLUME If this is activated the PARAMETER rotary encoder will send MIDI Volume messages 0 127 allow ing you to control the level of the external device The external instrument may have to be set to re ceive MIDI CC messages for this to function You can turn this off on the Extern menu see Extern menu on page 70 PROG GHANGE When this is on the PARAMETER rotary encoder will send Program Change messages 0 127 This allows you to select Programs for the external instrument This works slightly differently than for oth er parameters The Parameter rotary encoder will in this mode send a Program Change message for each individual rotary encoder LED To access all 127 messages simply continue to turn the rotary encoder multiple times it will continue to send messages across the whole range The external in strument may have to be set to receive MIDI Program Change messages for this to function You can turn this off on the Extern menu see Extern menu on page 70 If the externa
35. IDE em UNISON AUTO STORE SYNTH In this section you set various voice modes for the synth You choose between monophonic and poly phonic playing and control glide between notes Here you also find the powerful Unison mode MONO MODE In Mono mode you can only play one note at a time just like on a traditional monophonic synthesizer If you play one key and then a second key without releasing the first key the last note will sound If you now release the last key the first one will retrig and start sounding again To activate Mono mode press the SELECTOR button so that the MONO LED lights up LEGATO MODE To activate Legato mode press the SELECTOR button so that the LEGATO LED lights up In Legato mode you can only play one note at a time just like on a traditional monophonic synthe sizer If you play a new key before releasing the previously played key legato the new note will replace the previous one at the current Envelope phase of the previously pressed key I e the new note will not retrigger the Envelopes Amp and Mod If you release the last played key before playing a new key non legato the new note will sound ex actly like in Mono mode i e the complete Envelopes will be retriggered GLIDE PORTAMENTO When activated the Glide function makes the pitch glide from one note to the next when playing this is sometimes called portamento It operates in legato mono mode only The glide characteristics
36. Instruments The Synth section Nord Stage EX v6 x WAVES IN THE ANALOG CATEGORY The Analog category has ten waveforms to choose from summarized in the chart below Wave display Waveform Explanation S Sawtooth A plain sawtooth oscillator Sd Sawtooth detuned Two sawtooth oscillators with adjustable relative pitch Timbre knob and detune Unison knob S Sawtooth synced A sawtooth oscillator with adjustable pitch offset hard synced by a second oscillator P Pulse One pulse oscillator with variable pulse width PF Pulse fixed time One pulse oscillator with adjustable pulse width The pulse width is constant over the keyboard P Pulse synced A pulse oscillator with adjustable pitch offset hard synced by a second oscillator t Triangle A plain triangle wave oscillator t Triangle synced A triangle oscillator with adjustable pitch offset hard synced by a second oscillator C Cos synced A cosine oscillator with adjustable pitch offset hard synced by a second oscillator n Noise A white noise generator When you change waveform the name of the currently selected waveform is shown briefly in the MAIN DISPLAY SAWTOOTH The sawtooth wave contains all harmonics and is the richest of the available waveforms It is suitable for all sorts of sounds Amplitude Amplitude Time Y Harmonic number 10 20 30 40 Frequency The sawtooth signal shape The sawtooth signal frequency spectru
37. MAERUNEEERENNS RBS NEM EE E 71 GS UPGRADES EETERLEHILILIITLIIIULT 71 s 72 TE EXER TOUR eerie pscesus MRemUIEI MORIR RRUEPEE PA EU E SCOBMK I MENU EIER ERES 75 NORD STAGE MANAGER REFERENGE sesessesessscccnnneccecansecesanseeonannesonas 79 TARS aes OTT PERIERE aa ABOUT THE MIDI IMPLEMENTATION sscssssesssesesesssasseseveuseseUsasossPRSuseUE 86 USING NORD STAGE WITH A SEQUENCER 87 PROGRAM CONTROLLER AND SYNTH SOUND 88 8o 1 Es MIDI IMPLEMENTATIGQN ssss2522222222222222222222222222222222 JL MID CONTROLLER LIST rei RSS EIn ERR E EMI ERA 90 MIDI IMPLEMENTATION CHART rnnocnnuuuannuennasuuanuacunauaaunuacunauuaauuan 93 INDEX 29 Table of contents Nord Stage EX v6 x Nord Stage EX v6 x 1 Introduction Welcome 1 INTRODUCTION WELCOME We d first like to thank you for purchasing the Nord Stage EX Eighty Eight Seventy Six Compact Clavia s goal when develo
38. Manager Overview Nord Stage EX v6 x 13 NORD SOUND MANAGER File Edit View Help A NH ma o m m BN BH Organize DualView Auto Select SoundUp SoundDown Rename Delete BankUp Bank Down Backup Restore Piano Program Synth Bank 126 sounds Bank a Loc Name Ver Info Page 1 1 Studio Grand2 XL 3 16 Page 1 2 Concert Grand 3 16 c3 Page 1 3 Stage Grand 3 16 Page 1 4 Rain Piano 3 16 Page 1 5 Electric Grand 3 16 Page 1 6 E Grand Custom 3 16 Page 2 1 DeepE Piano 3 16 Page 2 2 Suitcase E Piano 3 16 Page 2 3 Shallow E Piano 3 16 Page 2 4 EPiano Mark V 3 16 Page 2 5 Wurlitzer 3 16 Page 2 6 Clavinet 1 3 16 Page 3 1 Clavinet 2 3 16 Page 3 2 Clavinet 3 3 16 Page 3 3 Clavinet 4 3 16 Page 3 4 Harpsichord Ital 3 16 Program partition 126 126 used Nord Stage EX connected 1 sound selected Connected Nord Stage EX The Nord Sound Manager is the application that allows you to organize the various memory areas the partitions in the Nord Stage EX It is also used to download pianos programs or synth patches to the Nord Stage EX or to upload any of these items called sounds from the Nord Stage EX memory to the computer hard drive The Nord Sound Manager provides access to various methods to down load the sounds to the unit and a function to backup and restore the entire Nord Stage EX memory SYSTEM REQUIREMENTS The Nord Sound Manager is compatible with computers running Mac OSX 10 4 or la
39. NO age ex User Manual Nord Stage EX OS Version 6 x Part No 50250 Copyright Clavia DMI AB 2010 Print Edition 6 0 CAUTION ATTENTION RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE SHOCK ELECTRIQUE NE PAS OUVRIR CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL ATTENTION POUR EVITER LES RISQUES DE CHOC ELECTRIQUE NE PAS ENLEVER LE COUVERCLE AUCUN ENTRETIEN DE PIECES INTERIEURES PAR L USAGER CONFIER L ENTRETIEN AU PERSONNEL QUALIFE AVIS POUR EVITER LES RISQUES D INCIDENTE OU D ELECTROCUTION N EXPOSEZ PAS CET ARTICLE A LA PLUIE OU L HUMIDITET The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated voltage within the products en closure that may be of sufficient magnitude to constitute a risk of electric shock to persons Le symbole clair avec le point de fl che l int rieur d un triangle quilat ral est utilis pour alerter l utilisateur de la presence l int rieur du coffret de voltage dangereux non isol d ampleur suffisante pour constituer un risque d l ctrocution The exclamation mark within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product Le point d exclamation l int rieur d un tr
40. NOBS There are two types of knobs on the Nord Stage EX Rotary Encoders that show the position with red LED indicators These always reflect the true value and can also be controlled using the Morph function see About Morph Assign on page 60 PARAMETER Other knobs are of the potentiometer type After you load a program the cor responding parameter may not correspond to the actual position of the physical knob As soon as you begin turning a knob the parameter value will snap to the knob s physical position The display will indicate the parameter value if the corresponding section is active with an exception for the Effect parameters These will be shown regardless of the Effect sections active status Page 8 Nord Stage EX v6 x 2 Overview About Knobs amp Buttons THE BUTTONS There are three types of buttons for editing sounds on the Nord Stage EX SELECTOR BUTTONS PIANO SELECT Press the SELECTOR button repeatedly to select between options printed next to the corresponding triangular LED see figure CLAV HPS A GRAND WURL A UPRIGHT E PIANO E GRAND ON OFF BUTTONS The ON OFF buttons have a LED next to them to indicate the status DRAWBAR BUTTONS The DRAWBAR buttons are special in the way that they auto increment decrement the corresponding parameter when held I e if you hold a DRAWBAR button the corresponding drawbar parameter will continue to increment or decrement within its range
41. OMMON FEATURES ACTIVATING THE SUSTAIN PEDAL PITCH STICK FOR INSTRUMENTS You can freely set which instruments should respond to a connected Sustain Pedal and to Pitch Bend To activate the Sustain pedal for an instrument press SHIFT SUSTPED button in the correspond ing instrument section so that the SUSTPED LED lights up below the button You use the same gen eral method to deactivate reception of Sustain for an instrument section which in that case turns off the SUSTPED LED indicator To activate Pitch Bend for an instrument section press SHIFT OCTAVE SHIFT PSTICK button in the corresponding instrument section so that the PsTICK LED lights up PSTICK SUSTPED The bend range is fixed to 2 semitones Page 22 Nord Stage EX v6 x 6 The Instruments Common Features LEVEL ENCODER The LEVEL rotary encoder allows you to adjust the volume for the instrument Instrument level can be Morph controlled KB ZONE SELECT BUTTONS The KB ZONE SELECT buttons allow you to assign the instrument to Keyboard Zones to create splits and layers This is described in Keyboard Zones and Dual Panel setups on page 56 Pp oe KB ZONE SELECT OCTAVE SHIFT Each instrument has a finite note range You can use Octave Shift to shift the pitch up or down within the instruments note range See Octave Shift on page 58 for more information OUTPUT ROUTING The Nord Stage EX has four audio outputs Each instrumen
42. P FILTER FREQ CONTROL 5 ag 456 3 7 7 7 i 2 8 rui yn 8 8 REL DECAY Ww 1 9 1 9 REL DECAY ENV MODE s 10 10 VELOCITY MOD ENV KB TRACK REP RESONANCE SM Ale N CATEGORY Basics The Synth section in Nord Stage EX was designed to be a versatile yet easy to use stage synthesizer to complement the other instrument sections While being compact and easy to use it is capable of all kinds of synthesized sounds from piercing leads and fat basses to swirling pads and shimmering bells And you have hands on control over all parameters which is essential on a stage instrument It is based on traditional subtractive synthesis with faithful models of analog style waveforms but it is also capable of FM frequency modulation and Wavetable synthesis In subtractive synthesis you start with a bright waveform with lots of overtones and then shape the colour of the sound with a filter usually a low pass filter that removes some of the upper harmonics By modulating the filter cut off frequency while the note is playing dynamic timbres are created The Nord Stage Synth also provides other means to generate dynamic and rich sounds such as pulse width modulation oscillator sync and dynamic control over FM amount There are two envelopes one of them loopable one LFO for vibrato and a simple EQ for one the fly sound shaping The ba sic signal path is shown with grey boxes and arrow
43. R rotary encoder ABOUT KEYBOARD ZONES There are two Extern sections one for each panel You can use Keyboard Zones to create splits and layers just like for the internal instruments If you set the Extern section to only play in the LO Zone the external instrument will only respond to notes played in this Zone In other words it works trans parently together with the built in instruments Page 63 10 The Extern section The Parameter section Nord Stage EX v6 x In addition to the usual Keyboard Zones there is an extra option that doesn t assign the Extern section to the internal keyboard at all However all other External features are still active such as the Pitch Stick and the PARAMETER knob This is useful when you want to control external equipment with no need for MIDI keyboard messages See Keyboard Zones and Dual Panel setups on page 56 for information on how to set up and use Keyboard Zones OCTAVE SHIFT The OCTAVE SHIFT buttons in the extern section also work exactly as for internal instruments As with them the shift range depends on the total note range of the external instrument and the range of the Keyboard Zone s that the external instrument is currently assigned to See Octave Shift on page 58 ACTIVATING PITCH STICK SUSTAIN PEDAL MESSAGES By pressing SHIFT and one of the PSTICK or SUSTPED buttons you can set up whether Nord Stage EX should send Pitch bend and or Sustain pedal messages via the Extern MI
44. Synth one Extern section as well as four Panel effects Effect 1 2 Delay and Amp Sim EQ Thus within a single Program you can use up to six instruments two external instruments and eight independent effects Page 14 Nord Stage EX v6 x 4 Getting Started Setting output Level for instruments SETTING OUTPUT LEVEL FOR INSTRUMENTS Each instrument has a LEVEL rotary encoder at the top of the panel This adjusts the output level for the corresponding instrument section The LEVEL encoders can be controlled in a Morph scenario ADDING A GLOBAL EFFECT Nord Stage EX features four effect groups the Rotor section rotary speaker effect psmegemmmmmm the Effects section three separate effects units Effect 1 2 and Delay the Ampsim EQ section overdrive and amplifier speaker modelling with EQ and a Compressor and Reverb section The Compressor and Reverb effects are global and affect all in 7 struments routed to the main CH OUT 1 2 jacks The Rotor can process the same E instrument from both panels Organ A amp B Piano A amp B or Synth A amp B The other HE effects can process one freely selectable instrument per Panel ACTIVE REVERB To add a global reverb effect to a sound simply press the ON button in the Reverb d Me section STAGE 5 Stage 507 gt Now you can adjust the amount of reverb effect using the DRY WET knob and set the basic reverb character Hall Hall soft Stage Stage soft R
45. The Program section What is a Program To copy the settings from another Panel to the selected Program Panel press and hold one of the Pan el buttons and turn the Value dial The display will indicate which of the Panels in the entire Program memory of the Stage that will be copied to the current Program Panel WHAT IS A PROGRAM A Program basically stores everything except System functions which are mostly global To under stand the internal architecture in Nord Stage EX keep the following in mind For each Panel settings for all three Instruments the four Panel Effects and the Extern section are independent except the choice of organ model which is always shared between the panels A Program stores settings for both Panel A and B so a Program contains independent settings for six instruments eight Panel Effects and two Extern sections A Program also stores all settings from the Extern menu except the Extern A amp B MIDI channels and the Send on Load setting see Extern menu on page 70 and the output routings for each instrument see System menu on page 66 The Global effects Compressor Reverb and the Rotor effect affect both Panels and are stored with the Program as well Splits layers Keyboard Zones and Morph assignments are of course also part of a Program ABOUT THE LIVE 1 amp 2 BUFFERS The special Live memory feature can be described as a live program memory If you activate
46. a program is loaded the same moment you press a PROGRAM button or as soon as you turn the VALUE DIAL Sometimes you may want to browse through the programs without leaving the cur rent program for example while still playing with the other hand Then you can use the pending pro gram change feature While pressing SHIFT turn the VALUE DIAL until you see the program you want to load in the DISPLAY Release the SHIFT button The corresponding PROGRAM BUTTON will flash to show you that it is ready to load Press the flashing button to load the program f you change your mind press EXIT SHIFT to cancel the operation PAGE BUTTONS The PAGE buttons are used to select Program Pages and to navigate between System menu pages Hold either button to browse quickly through the pages When combined with the SHIFT button the PAGE buttons step through all the 121 available Pro grams DISPLAY The MAIN DISPLAY normally shows the name of the currently selected Program but is also used for displaying various system parameters and messages THE SHIFT EXIT BUTTON SHIFT Many buttons and knobs have secondary functions that you can access by holding down SHIFT and pressing the button or turning the knob The Shift induced functions are always printed below the corresponding button or knob For example pressing SHIFT PRO GRAM 3 button will allow you to access the MIDI system parameters ETE In a few cases the shift
47. accessories specified by the manu facturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate nor mally or has been dropped Additional Safety Information No naked flame sources such as lighted candles should be placed on the apparatus Do not use the apparatus in tropical climates WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus The maims plug is used as the disconnect device and shall remain readily operable Il convient de ne pas placer sur l appareil de sources de flammes nues telles que des bougies allum es L appareil n est pas destin tre utilis sous un climat tropical L appareil ne doit pas tre expos des gouttements d
48. ager lists or in the Stage display Pianos cannot be renamed so this function is not available if you have selected a piano DELETE Allows you to delete one or several selected sound You will be asked to confirm your intentions You may also use the delete or backspace key on the computer keyboard to perform the deletion Note Any Program in the Nord Stage that used that particular piano or synth patch that you de leted will probably sound very different since it will be missing an important component The space that a deleted Piano occupied is not immediately available to other pianos even though it is gone from the list and its location is free The Flash memory needs to be cleaned to free up the space where the deleted sounds have been When you add a new piano sample the cleaning process will be initiated automatically You also have the option to manually start the cleaning process with the Clean Deleted Space command from the File menu Page 79 13 Nord Sound Manager Nord Sound Manager reference Nord Stage EX v6 x Note A flashing number in the Nord Stage EX piano type LED indicates that the Piano location that the current Program tried to use is not available in the Flash memory Select another piano type or download the missing piano sample to the Stage BANK UP This function will upload an entire bank of piano samples programs or synth patches to the computer hard drive The default source will be the currently active ban
49. ailable memory slots are divided into three categories Synth Pad and Bass with 99 memory slots in each category a total of 297 sounds Having categories helps you quickly find the type of sound you are looking for Use the two SOUND SELECT UP DOWN buttons to step through all the available sounds To jump between categories press SHIFT and the CATEGORY buttons When you select a sound the name is shown briefly in the MAIN DISPLAY The smaller LED Display in the Sound Select section always shows the patch number If a Synth sound has been edited a dot is shown after the number to reflect this in the SOUND SELECT DISPLAY SOUND SELECT SYNTH 2 BASS STORING SYNTH PATCHES To store a Synth Patch press SHIFT and the STORE SYNTH button in the Voices section The display in the Sound Select section starts blinking You can now use the SOUND SELECT UP DOWN buttons to navigate to a memory location where you would like to store your Patch To switch category press SHIFT and the CATEGORY buttons To name a Synth Patch you can use the PAGE buttons to move the cursor and the VALUE DIAL to select character just as for Programs see page 13 To store press the STORE SYNTH button again SOUND INIT To start with a clean slate when programming sounds you can use the Sound Init function This will initialize the Patch to basic default settings This is done by pressing SHIFT and SOUND INIT Page 48 Nord Stage EX v6 x 7 The Effe
50. al tonal characteristics The unique voicing brings out the best of this 9 foot beast you just add a bit of your talent to create wonderful musical moments nance feature A Grand 2 Studio Grand 2 Ya C7 This is a Japanese grand that we meticulously prepared in order for it to be as expressive as possible The mic s were positioned close to the strings and it is sampled in stereo The medium version has additional pedal down resonance samples and can take advantage of the String Reso Upright 1 Black Upright Petrof Sml Our Black Upright is a Petrof 132 upright piano It is a tall piano and typically used for musical schools in clubs and homes Upright 2 Romantic Upright Schimmel Sml Touch and tone are harmonized perfectly from the powerful bass notes up to the sparkling treble register This upright shines in every aspect with its beautiful and delicate sound E Grand 1 A CP 80 Electric Grand a classic touring grand from the eighties Page 31 6 The Instruments The Piano section Nord Stage EX v6 x E Piano Electric Piano Mk Stage Piano SeventyThree It was built in May 1978 and was adjusted to deep timbre adjustment The volume adjustment is set to Low These settings gives the piano a warm sound with a rich fundamental E Piano Electric Piano Mk I Suitcase Built in January 1975 We fine tuned the mechan ics and adjusted the tines according to the ideal timbre adjustment The vol
51. ance 45 Filter Frequency Cutoff Synth 44 Filter Section Synth 44 Fine Tune 66 Flanger effect 52 FM Synth 39 Focus button Effects 50 Frequency Control Filter modulation 46 Front panel 7 Page 95 Index G Glide Synth 46 Global Effects Compressor 54 Reverb 54 Instruments Activating 13 Internal memory 71 Internet 6 K KBT Filter 45 Key click control B 3 organ 26 Keyboard About 8 Keyboard splits 56 Keyboard Tracking Filter 45 Keyboard Zones 56 Knobs About 8 L Legato mode 46 Live Buffer memory 19 Live Buffer mode 18 Live buttons 18 LP Filter Synth 44 M Master level 7 Memory internal 71 Memory Protect 68 MIDI about the implementation 74 channels using with sequencer 75 connections 75 Controller list 78 controllers chasing when using a sequencer 76 recording in sequencer 76 implementation chart 81 Page 96 Nord Stage EX v6 x local on off 75 Program Change 75 recording in sequencer 75 Program dump 76 send all MIDI controllers 77 Sysex dump of single Programs 76 Sysex reception of Program and Program Banks 77 MIDI Page 68 Mod Envelope Attack 41 Decay Release 42 43 Modulation Envelope 41 Repeat mode 42 Mono mode 46 Morph Assign About 60 Assignable parameters 61 Clearing 62 Multiple keyboards 59 N Note On Off MIDI transmission and reception 74 Octave Shift 58 Octave Shift Extern section 64 Organ B 3 section 24 Organ Key Cli
52. anel setups on page 56 INSTRUMENT INITS Alternatively you can use the following method to select one of four basic INSTRUMENT INIT setups Init Organ Init Split Organ Init Piano Init Synth This will activate the corresponding instrument and deactivate all other instruments 1 Hold down the SHIFT button 2 Press one of the ORGAN SPLIT ORGAN PIANO OR SYNTH buttons in the Program section to activate the corresponding instrument section The Split Organ setup uses a split for a Lower Upper manual organ where the lower half of the keyboard plays an organ belonging to Panel A and the upper half plays Panel B see About Split Organ Setups on page 29 Page 13 4 Getting Started About Panel A amp B Nord Stage EX v6 x ABOUT PANEL A amp B All instruments in Nord Stage EX are two part multitimbral This means that each instrument section can produce two sounds simultaneously with completely independent settings The key to this fea ture are the two Panels A and B The two PANEL buttons A and B selects which Panel is currently active or edit active see below Each Panel controls three instrument sections and four Panel effects Having two Panels with their own settings not only allows you to alternate between two sound setups within a selected Program It also lets you have both Panels activated giving you access to two simultaneous instruments in each section e g a Electric Piano and a Clavinet two Synths etc I
53. annel is set here you can assign the corre sponding instrument to no KB Zone at all i e make it active but available only through MIDI MIDI Piano A B This sets the MIDI channel for the Piano section A B 1 16 Off Default off Channel If a channel is set here you can assign the corre sponding instrument to no KB Zone at all i e make it active but available only through MIDI MIDI Synth A B This sets the MIDI channel for the Synth section A B 1 16 Off Default off Channel If a channel is set here you can assign the corre sponding instrument to no KB Zone at all i e make it active but available only through MIDI MIDI Dual KB This sets the MIDI channel for an external keyboard 1 16 Off Default 16 Channel when using Dual KB mode see page 59 MIDI Prog Change Mode This allows you to set whether you want Nord Stage EX to transmit and or receive MIDI Program Change Messages Off Send Receive Send amp Receive Default MIDI Ctrl Change Mode Send MIDI Ctrl Dump Program Source This allows you to set whether you want Nord Stage EX to transmit and or receive MIDI Controller Mes sages You can perform a dump of all MIDI Controllers for the selected Panel Hit Store to perform the dump See Sending MIDI Controller dumps on page 89 Here you can perform a MIDI SysEx dump of the cur rently selected Program or of all 126 Programs of the internal memory plus the Live buffers 1 amp 2 See
54. are three types available with different characteristics Amp Model Description Amp 3 A simulation of a Roland Jazz Chorus speaker cabinet powered by a tube amp Amp 2 A simulation of the Wurlitzer 200A internal speaker powered by a tube amp Amp 1 A simulation of a Fender Twin tube ampli fier and speaker cabinet If all LEDs are off the effect combines EQ with overdrive no amp speaker modelling GLOBAL EFFECTS COMPRESSOR If activated the Compressor and Reverb effects will process all signals routed to ACTIVE the CH 1 CH 2 outputs but do not affect any signals routed to the CH 3 CH 4 out puts Both these effects are stereo in out d AMOUNT COMPRESSOR Mc The Compressor will even out the dynamics of what you play making low level sounds louder and high level sounds lower This produces a tight punchy sound REVERB and makes the overall level easier to control in a live mix situation You activate ea the Compressor using the ON button The AMOUNT knob controls the amount of 64 t sort compression applied REVERB The Reverb section simulates the natural sound reflections in various acoustic en vironments You can choose between five reverb types indicated by the three LEDs lit one or two at a time Reverb name Description Hall soft A reverb with the response and character of a spacious hall with long decay and a mellow character Hall 2 A hall reverb with a slight
55. awbar setting before the recorded change and therefore cannot chase the settings properly To solve this you could record a snapshot of all Controller settings of the Nord Stage EX Program s at the beginning of your sequencer song See Sending MIDI Controller dumps below PROGRAM CONTROLLER AND SYNTH SOUND DUMPS To dump Program Synth Sound or MIDI Controller SysEx via MIDI either to another Nord Stage EX or for recording the data into another MIDI device proceed as follows SENDING PROGRAM DUMPS 1 Connect a cable from MIDI OUT on the Nord Stage EX to MIDI In on the receiving device 2 Set up the receiving device so that it accepts MIDI SysEx and MIDI Controller data 3 Press SHIFT MIDI and select the Dump Program Source menu item using the PAGE but tons Here you can select whether to send all Programs ALL or the currently selected pro gram ONE by using the VALUE DIAL 4 If needed set the receiving MIDI device to recording mode 5 Press the STORE button to send the dump to the MIDI OvT of Nord Stage EX The Store indica tor will stop flashing once the dump has been sent To quickly send a dump of the current Program press SHIFT DUMP ONE the PANEL A button Note For Organ and Synth sounds the complete settings for the sound will be dumped as MIDI SysEx For Piano sounds all parameters will be sent but NOT the actual instrument samples Therefore when dumping back a Piano so
56. ay time time key release In Attack Release mode the control signal from the Mod Envelope stays at the maxi mum value until key release Time Attack time REPEAT In Repeat mode the Modulation Envelope restart directly after the Decay phase creating cyclic mod ulation like an LFO with shapable waveform where you can change the waveshape and cycle time by adjusting the Attack and Decay times Amount Time lt gt eao aca Attack Decay Attack Decay Attack Decay time time time time time time A slow looping Mod Envelope can be used for example to produce continuously sweeping pads while shorter Attack and Decay settings can produce special effects or repetitive sounds Page 42 Nord Stage EX v6 x 6 The Instruments The Synth section AMP ENVELOPE The final stage of a synth signal chain usually consists of an amplifier to control the signal volume By modulating the amplifier with an envelope the sound is given its basic shape over time In fact the volume shape is one of the most important factors to how we identify the sound By setting up a proper volume envelope you can make a sound soft plucked static etc The Amp Envelope has three modes Attack Decay ignoring the key release Z e Attack full sustain Release REL DECAY ENV MODE Attack Decay fixed short release l M Each mode ha
57. be assigned to no Keyboard Zone at all when no KB Zone indicator is lit This means that the instrument is active and you can adjust all parameters on the panel as usual but it can only be played via MIDI i e from your external keyboard or a sequencer Page 59 9 The Morph Assign feature About Morph Assign Nord Stage EX v6 x 9 THE MORPH ASSIGN FEATURE ABOUT MORPH ASSIGN The three main MORPH ASSIGN buttons are located in the Program section The Morph function can be used to control single or multiple pa MORPH ASSIGN rameters using the Wheel a connected Control pedal or After touch see About Aftertouch on page 62 This gives you plenty of real time control possibilities to augment your playing style It is very simple to up and use and all Morph assignments are stored with the Program WHEEL 9 A TOUCH 9 CTRLPED CLEAR MORPH emm Many of the Factory Programs have Morph assigned parameters If a Program uses Morph one or more of the MORPH ASSIGN indicators will be lit to indicate this E g ifthe WHEEL indicator in the Morph Assign section is lit for a Program you can move the wheel and all Morph assigned parameters will move correspondingly so you see exactly what parameters are currently assigned USING MORPH AN EXAMPLE In this example we shall describe how to assign Morph to the LEVEL rotary encoders for two Instru ment sections and use the Wheel to lower the level of one ins
58. ccess to some of the more frequently used functions in the Nord Sound Manager Clicking on an icon will activate one of these functions and a dialogue will often appear asking for confirmation or further instructions from you THE TABS Piano Program Synth Bank All 126 sounds v Select the partition that you wish to work in with the Tabs The Piano tab allows you to change the content of the Nord Stage piano partition the Programs tab is the program partition and the Synth tab allows you to organize the synth patches Each of these tabs is then divided into banks according to how the actual partition is organized in the Nord Stage EX The individual samples programs or patches will be referred to as sounds in this manual and in the application itself Tip Press Ctrl Tab on the computer keyboard to cycle between the three tabs In order to make organizing the content easier you can have two lists open by selecting Dual View in the View menu This makes it easy to e g drag a sound from one bank to another If a program or a patch is dragged and then dropped upon another program patch in the lists they will trade places Piano sounds can not be moved between the banks in the piano partition The bank lists can be ordered according to location name size version and date in ascending and descending order Just click on a headline to select a preferred view PARTITION MEMORY INDICATOR The memory indicator at the bott
59. channels This is done on the System page see page 66 MIDI CONNECTIONS f you are using a Nord Stage EX together with a MIDI keyboard connect a MIDI cable from MIDI Out on the keyboard to MIDI IN on the Nord Stage EX f you are using Nord Stage EX to control an external MIDI instrument connect a MIDI cable from MIDI OUT on the Nord Stage EX to the MIDI In connector on the other instrument Page 10 Nord Stage EX v6 x 3 Connections Connecting pedals CONNECTING PEDALS The Nord Stage EX has four pedal inputs one CONTROL PEDAL input configurable to control var ious Nord Stage EX parameters one ORGAN SWELL input one SUSTAIN PEDAL input and one Ro TOR SPEED input for rotary speaker fast slow selection You can select for each instrument whether it should react to sustain or not see Activating the Sustain Pedal Pitch Stick for Instruments on page 22 Connect the pedals as shown in the figure below When connecting an expression type pedal to the CONTROL PEDAL or ORGAN SWELL input you should use a stereo cable Tip Ring Sleeve Please note that the pedal must have a stereo output jack Pedals from various manufacturers have different characteristics To simplify setup the most com mon pedal models Roland Yamaha Ernie Ball and Fatar are preconfigured in the Nord Stage EX and you simply select the type of pedal in the System menu See Ctrl Pedal Type on page 67 for more information about this setting PEDAL
60. chronized oscillator with the TIMBRE knob this will be perceived as a change in timbre with a frequency spectrum with deep resonance in the oscil lator s harmonics Tip When using Oscillator Sync it can be very useful to have the Timbre amount s modulated from any of the Morph assign sources or by the Modulation Envelope This will generate a signal with continuously varied harmonic content If you choose one ofthe synchronized oscillator mode the Oscillator will start over with a new period of the waveform each time the sync oscillator does so If the Oscillator then has a higher frequency than the sync oscillator it will get a complex waveform that depends both on its own pitch and on that of the sync oscillator Page 38 Nord Stage EX v6 x 6 The Instruments The Synth section Example 1 a sawtooth wave synced by a sync oscillator The sawtooth wave is restarted every time the sync oscillator begins a new cycle The resulting signal gets deep resonance in its harmonics 4 Amplitude Amplitude Time gt Harmonic number 10 20 30 40 Frequency Oscillator non synched 4 Amplitude Sync oscillator Amplitude Amplitude Osc Harmonics Oscillator synchronized 10 20 30 40 Frequency Amplitude l Amplitude n i Osc Harmonics TAL il lath lu Harmonic number Oscillator at higher frequency synchronized 10 20 30 40 Frequency In the Nord Stage oscillator sync i
61. ck Level Sound Page 68 Organ Output 66 Organ Trig Mode 67 OS upgrades 73 Oscillator Analog waveforms 36 Sync 38 Waveforms Digital 41 FM 39 Pulse and Square wave 37 Sawtooth wave 36 Sine wave 38 Triangle wave 37 Oscillator section Synth 35 Output Level Instrument 14 Nord Stage EX v6 x P Page buttons 17 Panel A amp B 58 About 14 Edit focus 14 Panel Effects Activating 50 Ampsim EQ 53 Effect 1 51 52 53 54 Effect 2 52 Making settings for 50 Pan 51 RM ring modulation 51 Wah Wah 51 Panic button 77 Patch selector Synth 47 pdf file reading the manual as 6 Pedals Connecting 11 Rotor Speed 11 Percussion B 3 25 Phaser effect 52 Piano downloading new instruments via USB 72 Piano instruments Selecting 31 Piano Output 66 Ping Pong Delay Effect 52 pitch bend MIDI messages 74 portamento 46 Preset II button Organ section 29 Program Naming 21 reverting to stored 13 What is it 12 Program buttons 18 Program Change MIDI 75 Programs About 12 Saving 20 Selecting 12 Q Q value Filter 45 R Rear panel 10 Index Register selectors V type 28 Release Amp Envelope 43 Mod Envelope 42 Release velocity 74 Resonance Filter 45 Reverb 54 RM Effect 51 Roland control pedals 67 Roland Jazz Chorus 54 Rotor Effect 55 Rotor effect Internal routing 55 Rotor Pedal Mode 67 Rotor Pedal Polarity 67 Rotor Speed pedal Connecting 11 s Send On Load Extern 65 Shift button 17
62. created faith fully in Nord Stage EX THE DRAWBARS The original Vox Continental used drawbars to change the timbre of the sound The harmonic inter vals for the V Type organ are printed on the upper row above the drawbars see page 24 for a general description of how the drawbars work in Nord Stage EX In the figure you can see the pitch interval among the six drawbars used by the V Type organ Note that the 6th draw bar from left controls three E E harmonics simultaneously 3rd 4 2 4th 8th The two rightmost gt re drawbars determine mix of the two basic waveforms that ET sus FUND sm 34 808 BASIC STRIE n 20 03 sms UB FUND 2ND E ATH make up the sound generating source of the organ sound just like on the original You have access to sine soft and triangle bright waveforms which can be freely mixed together If these drawbars are both fully pushed in the organ will not C3 produce any sound In the illustration above we have chosen C3 as our reference note The FUND drawbar is considered the basic fundamental harmonic in the organ sound The arrows point at the respective note that each drawbar represents when C3 is our reference note VIBRATO There is only one type of vibrato available for the V Type which is activated using the ON button in the Vibrato section Note that the V Type vibrato is common for both Panels if a dual manua
63. cts About the effects 7 THE EFFECTS EFFECTS AMPSIM EQ COMPRESSOR ACTIVE AMOUNT RATE TEMPO AMOUNT 7 TREBLE 3 2 8 ON Jc EFFECT 1 EFFECT 2 DELAY 2 dj eee DRIVE aae DRIVE 10 REVERB 3 7 ORG PIANO SYNT 2 E FLANGI FLANG2 1 8 MD STAGE 10 AMP 3 7 A WAi 2 CHOR1 BTW ROOM AMP2 SOURCE 1 CHOR2 PING PONG 5 AMP 1 5 5 STOP 10 Wa 10 15 15 BASS TAP TEMPO ORG PIANO SYNT ORG PIANO SYNT ORG PIANO SYNT ORG PIANO SYNT SOURCE SOURCE SOURCE SOURCE ABOUT THE EFFECTS The effects available in Nord Stage EX can be divided into three main categories Panel Effects these can affect one instrument per Panel at a time Panel effects are the effects in the main Effects section and in the AmpSim EQ section All Panel effects have separate engines and settings for Panel A and B thus you have two sets of Panel effects available for each Program See below for a description of the Panel effects Global Effects these affect all instruments routed to the main outputs CH1 amp CH2 The Com pressor and Reverb on the far right of the front panel are global effects See page 54 The Rotor Effect works slightly differently compared to Panel effects See Rotor section on page 55 ABOUT MONO STEREO AND EFFECT ROUTING Some of the effects are mono i
64. d Stage EX piano sounds with the default keyboard Dynamics setting This is because the dy namic response curves have been very carefully adjusted to match each original instrument s response characteristics In other words Clavia s intention was that when you play a Electric Piano sound for example it should almost feel like you are playing a Electric Piano However If you want the piano sounds to respond more easily to keyboard velocity you can set this in the following way Hold SHIFT and press the DYNAMICS button to select one of the four modes The LEDs to the right of the TYPE DISPLAY light up to indicate what mode is selected Select between 1 3 where 3 is the most compressed response If all LEDs are off this indicates the instrument s original sensitivity The Dynamics setting is saved with a Program Page 33 6 The Instruments The Synth section THE SYNTH ON OFF SECTION 4 5 3 2 2574 oO 6 GLIDE AUTO 8 zl 10 VOICES MONO LEGATO STORE SYNTH ANALOG gt OFF lt 10 SYNTH 1 VIBRATO DLY3 DLY2 DLY1 WHEEL SOUND INIT OSC GROUP Nord Stage EX v6 x TREBLE ACTIVE TIMBRE CONTROL KB ZONE SELECT OCTAVE SHIFT PSTICK FM WAVE 456 ITAL C e 3 7 DIGITAL j E 5 9 S 4 N 1 Z 9 10 VELOCITY MOD ENV SUSTPED ATTACK ENV VEL TIMBRE SOUND SELECT CATEGORY SYNTH PAD BASS L
65. d as a Sys tem Exclusive dump see Sending Program dumps on page 88 USING NORD STAGE EX WITH A SEQUENCER CONNECTIONS 1 Connect the MIDI Out on the Nord Stage EX to the MIDI In on your sequencer 2 Connect the MIDI Out from your sequencer to the MIDI In on the Nord Stage EX Make sure that the Nord Stage is configured to respond to Program Change and Control Change MIDI messages see the menu on page 68 LocAL ON OFF Local Off should be used when you use a sequencer to record and play back from Nord Stage EX Since the sequencer echoes back incoming MIDI data Nord Stage EX will respond normally to your playing and knob tweaking via the MIDI If you use Local On with a sequencer setup as de scribed above this would cause double triggered notes when you play both from the keyboard in ternally and via the MIDI loop Therefore always use Local Off when used in this way together with a sequencer Local On Off is set on the MIDI menu on page 68 MIDI CHANNEL Each Panel can respond its own MIDI channel This is convenient when you want to play split and layered sounds If you want to control each instrument separately you can assign an individual MIDI channel to each of the six instruments of the Nord Stage The MIDI channels are set up on the MIDI menu see MIDI menu on page 68 PROGRAM GHANGE Usually you select a Program Change value for a track in the sequencer track
66. d in certain circumstances like to use to play the Nord Stage EX double manual By activating Dual KB you can quickly switch between these modes without hav ing to bother with MIDI menus Having this function easily accessible on the front panel makes its easy to turn off and prevent the external keyboard to play when its used to play its own sounds Another advantage with the Dual KB mode is that you can access the knobs and parameters for either panel from the Nord Stage while the internal keyboard is always playing Panel A and the external keyboard controls Panel B For example you can keep on playing Panel A with one hand on the in ternal keyboard while you simultaneously adjust the drawbars for the second keyboard on Panel B Please note that the Dual KB setting is saved with a Program together with all other Panel settings This makes it easy to access any complicated keyboard setup with the push of a button ideal for live situations USING MULTIPLE KEYBOARDS Sometimes you may want to control the Nord Stage from more than two keyboards For example you may want to have two external keyboards for Organ A and B while keeping the internal keyboard for the piano sounds Thanks to the flexible MIDI configuration of the Nord Stage this is no problem at all The Nord Stage can be set up to receive on a separate MIDI channel for each instrument see MIDI menu on page 68 When such a MIDI channel is assigned the instrument can
67. do like this 1 Connect a cable from the MIDI Out on the transmitting device to MIDI IN on the Nord Stage EX 2 Initiate the transmission on the transmitting device If the dump contained all Programs All it will replace all Programs currently stored in the Nord Stage EX If the dump contained only a single Program One it will be temporarily placed in the currently selected Program memory location You will then have to store the Program manually to a memory location using the Store function see Storing Programs on page 20 PANIC If notes should hang using the Nord Stage EX in a MIDI setup all you need to do is hold down the SHIFT button and press the PANIC button in the Piano section This will execute an internal All Notes Off and reset certain parameters to their default values Page 89 15 MIDI implementation MIDI Controller list 15 MIDI MIDI CONTROLLER LIST Nord Stage EX v6 x IMPLEMENTATION The following is a list ofthe MIDI Controller numbers used for all KNOBS and BUTTONS on the front panel Page 90 Nord Stage Parameter MIDI Controller Organ Preset II 3 Organ Swell 4 Organ Drawbar 1 9 Organ Drawbar 2 14 Organ Drawbar 3 15 Organ Drawbar 4 16 Organ Drawbar 5 17 Organ Drawbar 6 18 Organ Drawbar 7 19 Organ Drawbar 8 20 Organ Drawbar 9 21 Organ Percussion Enable 22 Organ Type 23 Organ Vibrato Type
68. e For A Wha you control the filter sweep range from the signal s amplitude envelope envelope follower For the Auto Wah 1 modulation you control the range with the RATE TEMPO knob and the wet dry mix with the AMOUNT knob A Wha 2 works in the same way but produces a different character EFFECT 2 Dl sani The Effect 2 section offers six types of vintage style effects to add that extra flavour to your sounds FLANG1 FLANG2 PHAS2 CHOR1 FLANGER 1 amp 2 PHAS1 CHOR2 The flanger produces a very characteristic comb filter effect You set the flanging rate with the RATE TEMPO knob and the amount with the AMOUNT knob The Flanger ef fect is mono in out ORG PIANO SYNT PHASER 1 amp 2 7 The phaser effect produces a very characteristic sweep effect commonly used with on electric piano sounds You control rate of the phase shift with the knob and the phase shift amount with the AMOUNT knob This effect is mono in out CHORUS 1 amp 2 The Chorus effect simulates having several slightly detuned signals You set the rate for the chorus effect with the RATE TEMPO knob and the amount with the AMOUNT knob This effect is stereo in out DELAY The Delay effect produces echo repeat effects You set the Delay time with the RATE TEMPO knob 745 0 1ms While you turn the knob the delay time and corresponding tempo and rhythmic subdivision will be shown briefly in the DISPLAY The AMOUNT AERE knob adju
69. e command is also available in the File menu Sound Download Ctrl D 2 Browse to the folder on the hard drive where the desired sound is located select it and click Open The piano will now be added to its parent bank These methods can also be used with any individual Programs or Synth patches that you wish to add Page 76 Nord Stage EX v6 x 13 Nord Sound Manager The Quick Tour UPLOAD ONE OR SEVERAL SOUNDS FROM THE NORD STAGE TO THE HARD DRIVE 1 Select the desired partition that holds the sounds that you wish to store on the computer hard drive 2 Select the bank and the sound Shift click will allow you to select several consecutive sounds Ctrl click will allow you to select nonconsecutive sounds Here we have selected a few of the Programs Deep E Piano Shallow E Piano E Piano Mark Wurlitzer Clavinet 1 Clavinet 2 Clavinet 3 Clavinet 4 70s Rock Grand Ambient Grand 3 14 FosterPiano 3 14 w LES 1 gt Te Ses cn 3 Click on the Sound Up tool or right click on the selected sound s and select Upload The dia logue will prompt you to browse to the desired destination folder on the hard drive The upload process may take a few moments depending on the size of the sounds UPLOAD A COMPLETE BANK OF SOUNDS FROM THE STAGE TO THE HARD DRIVE 1 Make sure that the desired partition and bank is focused in the Nord Sound Manager You will also have the opportunity to change the source bank in an upcom
70. e PANEL button you want to disable Press and hold a Panel button and turn the value dial to copy the Panel settings from another Program to the one currently active Page 58 Nord Stage EX v6 x 6 Keyboard Zones and Dual Panel setups Dual Panel setups When you have both Panels active you have access to two of each Instrument section and two Effect sections Amongst other things this allows you to play two sounds from each Instrument section si multaneously e g a Clavinet and a Electric Piano or two Synths For the Organ section things work slightly differently Instead of two completely separate organ sections you have one organ engine with two manuals i e different drawbar settings like on a real B3 See About Split Organ Setups on page 29 USING AN EXTERNAL KEYBOARD DUAL KB If you like to use an external keyboard to control Panel B you set it up as follows Select a MIDI channel to transmit over from the external keyboard and select the same MIDI channel as the Dual KB channel on the Nord Stage EX MIDI page menu see MIDI menu on page 68 Press SHIFT and the DUAL KB button so that the DUAL KB indicator lights up Now the internal keyboard will control Panel A and the external keyboard will control Panel B It is not possible to activate both Panels in this mode This function is ideal for live situations when you have a second keyboard in your rig that you mostly use to play internal sounds but woul
71. e digital PDF file format It can be downloaded free of charge from Clavia s web site at http www nordkeyboards com When reading the manual as PDF file you will need Adobe Acrobat Reader 4 0 or later This program can be downloaded free of charge at http www adobe com With Adobe Acrobat Reader it is possible to use special navigation features like hyperlinks This means that you can click with the mouse on a word or sentence and automatically get to the location indicated by the word sentence To better show what words or sentences are hyperlinked in this man ual these words are written in magenta NORD ON THE INTERNET If you have access to the Internet you re very welcome to visit http www nordkeyboards com There you will find the latest information about Nord Stage EX and other Nord products You can also download new Nord Stage EX sounds and software upgrades free of charge Page 6 Nord Stage EX v6 x 2 Overview The Nord Stage EX front panel Z LIVERVIEW THE NORD STAGE EX FRONT PANEL Program Organ section section Synth section Effects section Master Piano Extern Level Rotor section section effect section THE PROGRAM SECTION The central Program section is where you select and store Programs access System parameters ac tivate keyboard zones for splits and layers and assign Morphing functions See The Program sec tion on page 16 for details MASTER LEVEL ROTOR SECTION The leftm
72. e to the wavelength usually in see above The Pulse Fixed Time algorithm instead generates a pulse wave where the pulse width is adjusted in absolute time values with the TIMBRE knob i e the pulse width is constant over the keyboard This results in a spectrum with fixed formants similar to the character of many acoustic instruments The waveform in itself 15 not different from the normal Pulse algorithm but it behaves differently over the keyboard range TRIANGLE The triangle waveform has only odd numbered and not very strong harmonics It is suitable for flute and similar sounds Page 37 6 The Instruments The Synth section Nord Stage EX v6 x NOISE The noise waveform is a chaotic waveform containing all frequencies at the same time With the res onant filter and the EQ you can shape it to produce special effects e g wind noises and whistling sounds OSCILLATOR SYNC WAVEFORMS The Saw Square Triangle and Cosine waveforms can be synchronized These modes are marked with a special character in the WAVE DISPLAY Oscillator Synchronization means that you use the signal from one oscillator to restart another oscillator Nord Stage EX has a hidden sync oscillator for waveforms with this option Oscillator sync is very useful for generating lead lines with classic hard sync sounds When sync is applied the basic pitch of the oscillator is locked to that of the sync oscillator When you vary the relative pitch ofthe syn
73. e used simultaneously by acti vating both Panel A and Panel B Press this button repeatedly to select one out of three detune depths The setting will have no effect if only one Panel is active DLAv EQ PIANO RES If you press the Piano Res button when a Grand or an Upright is selected the String Resonance func tionality will be activated This mimics the behavior inside an acoustic piano when strings or parts of strings may resonate at their fundamental or overtone frequencies when other strings are sounded This feature is only available on the v4 XLR pianos and on the v5 pianos read more on our web site DLAv EQ PIANO MONO If you press the A Piano Mono button when a Grand or an Upright is selected the stereo sound will be played back in mono instead This can be useful if you only have access to one channel on a mixing desk ABOUT INFO If you hold SHIFT and the INFO button in the Piano Select section the display will show the instru ment s name and additional information about the currently selected instrument e g mic placement Close or Ambient and a revision number e g 5 Page 32 Nord Stage EX v6 x 6 The Instruments The Piano section CLAVINET SOUND CLAVEG On an original Clavinet D6 you can select different pick up and filter combi lt BRILL nations by pressing a number of rocker switches This functionality is very TREB faithfully simulated in the Nord Stage EX which means that you get all
74. eau ou des claboussures et de plus qu aucun objet rempli de liquide tel que des vases ne doit tre plac sur l appareil Lorsque la prise du r sau d alimentation est utilis e comme dispositif de d connexion ce dispositif doit demeur ais ment accessible Trademarks The Nord logo is trademark of Clavia DMI AB All other trademarks mentioned in this publication are the properties of their respective holders Specifications and appearances are subject to change without notice Copyright O Clavia DMI AB Nord Stage EX v6 x Table of contents TABLE OF CONTENTS 1 INTRODUCTION BESEEBBREERBEHBEBERRERERERERERERERBERERERERRERESBERRERERBRERRERERRSREREREBERE 5 WELCOME LESER REN tere S ABOUT THE OWNER S MANCLIAL ssescsssusunuassnuuuasnuassuuusauuaeenuanasansecens ON THE INTERNET 2 OVERVIEW BEB BBR BBP PPP PPP eee 7 THE NORD STAGE FRONT PANEL lt 7 THE REY BARD ins ABOUT KNOBS amp BUTTONS Rasa REAPER ener e CONNECTIONS BEBRBBERBERBBEREHEERBHEENHEERBEUEREEREEERBERBSEEBERBEREREEENERBBEBEBEREBSERENENSN 1 NORD STAGE REAR PANEL sssnnshasnue
75. election RENAME GTRL N Allows you to rename a sound 16 characters can be used and the supported characters are a z A Z 0 9 and the hyphen Any other characters will not be displayed in the Sound Manager lists or in the Nord Stage display Pianos cannot be renamed so this function is not available if you have selected a piano DELETE Allows you to delete a selected item s from the Nord Stage memory You will be asked to confirm your intentions Page 82 Nord Stage EX v6 x 13 Nord Sound Manager Nord Sound Manager reference SELECT ALL Select all items in a bank INVERT SELECTION This will deselect the original selection s and then select all the other items in the list VIEW ie Dual View Ctrl L Free Locations Ctrl F ORGANIZE CTRL O When this option is checked the lists will show all the available locations in the selected partition bank and not only the occupied ones This will for instance make it easier to drag a file to a specific free location in the middle of the list If this is unchecked only the occupied locations will be shown DUAL View CTRL L Select this option if you need to move items between different banks Please note that both lists rep resent the actual memory content in the Nord Stage Any actions that you make in either of the lists will affect the memory content in the Stage AUTO SELECT When this function is active programs will be automatically selected in the
76. er version 2 x or 3 x operating system INFO This area may contain error information about broken corrupted or rejected files if e g something has happened with a particular piano in the Stage EX FOOTER AREA The footer area is located at the bottom of the Nord Sound Manager window Piano partition 222 1 used 30 4 ME available Page 84 Nord Stage EX v6 x 13 Nord Sound Manager Tabs PARTITION MEMORY INDICATOR This indicates the usage of the selected partition s memory The red area shows the used memory and the green area indicates space that is available for additional sounds CANCEL BUTTON Use this function if you need to cancel a process that is in progress Certain functions like e g a re store process cannot be cancelled PROGRESS BARS The two progress bars indicate the progress of an ongoing process The upper bar shows the progres sion of the individual processes and the lower indicates the status of the entire task MESSAGE AREA TEXT AREA The left part of the text area will present any confirmations or error messages from the Nord Sound Manager The right part will indicate of a Nord Stage EX is connected to the computer and in communication with the Nord Sound Manager The OS version of the Stage will also be presented here UPDATES AND PIANO SAMPLES Please visit our website at http www nordkeyboards com to download any updates of the Nord Sound Manager and sounds that have been released
77. ete the selected sound s from the Nord Stage EX memory FILE FORMATS The Nord Sound Manager v5 x creates and uses files with the following extensions npno These are the piano samples nspg These are the Program files The file name will also be the name of the Program that is shown in the Nord Stage EX display nss This is the extension for the Synth patches The file name will also be the name of the Synth patch that is shown in the Nord Stage display nsb This is the extension used for the Nord Stage backup files Just as any other computer file on your hard drive these files may be renamed emailed copied moved lost or even stored in a safe location if an evil computer crash suddenly decides to take your hard drive for ride Page 74 Nord Stage EX v6 x THE QUICK TOUR Let s get acquainted with some of the functions in the Nord Sound Manager 13 Nord Sound Manager The Quick Tour TRANSFER PIANO SAMPLES TO THE STAGE When the Nord Stage EX leaves the factory the Piano partition is filled with piano sounds In order to be able to download additional pianos you may have to delete some of the factory pianos If you ever want to restore any deleted pianos they are available on the DVD that was included with the Nord Stage EX or available as a download from the www nordkeyboards com web site in the Nord Stage download area DELETING A PIANO FROM THE NORD STAGE EX 1 Connect the Nord Stage EX
78. eted Space Format Exit Ctrl Q SOUND UPLOAD GTRL U Use this function to upload one or several sounds from the Nord Stage memory to a folder on the com puter hard drive SOUND DOWNLOAD GTRL D Use this function to download one or several sounds from the computer hard drive to the next avail able location in the selected partition BANK UPLOAD GTRL SHIFTT U This allows you to upload an entire bank pianos programs or synth patches to a folder on the com puter hard drive Select the desired source partition and bank and the destination folder If you select All all the banks in the partition will be uploaded The hierarchical folder structure of the chosen partition partition bank sounds will be automatically created in the destination folder BANK DOWNLOAD GTRL SHIFT D Use this function to download an entire bank or all banks from the hard drive to the Nord Stage Please note that you need to match the format of the source and the destination it is e g not possible to download a set of pianos to any of the synth patches banks Note The content of the source folder will replace the selected bank in the Nord Stage Page 81 13 Nord Sound Manager Nord Sound Manager reference Nord Stage EX v6 x BACKUP CTRLT B This will make a backup of all the Piano samples Programs and the Synth patches in the Nord Stage The file that is created on the hard drive will have the extension nsb Backing up the entire memory co
79. flex ibility and sound control It is based on standard subtractive synthesis with a very flexible oscillator section that can produce all common analog style waveforms up to three oscillator FM synthesis and a bank of carefully designed wavetables for those unusual timbres The synth also sports a high quality resonant low pass filter with selectable slope two envelopes a simple EQ and a very pow erful Unison mode See The Synth section on page 34 THE EXTERN SECTION The Extern section controls an external MIDI instrument You can use the PARAMETER knob to con trol various parameters on the external device You can also assign the external instrument to any Keyboard Zone just like the built in instruments See The Extern section on page 63 THE EFFECTS SECTION Here you ll find the numerous effects and modulations you can use to add that extra flavour to your sounds See The Effects on page 49 THE KEYBOARD The keyboard of the Nord Stage EX features 88 76 medium weighted keys or 73 semi weighted wa terfall keys for optimal feel and response with piano instruments For organ sounds there is also a fast trigger response option which closely mimics the feel of a real organ The keyboard can be split into three Keyboard Zones to which any instrument section can be freely assigned Assigned Keyboard Zones are saved with a Program See Keyboard Zones and Dual Panel setups on page 56 ABOUT KNOBS amp BUTTONS THE K
80. for the Nord Stage EX These items will be avail able as free downloads in the Nord Stage EX download area Page 85 14 MIDI functions About the MIDI implementation Nord Stage EX v6 x 1 4 MIDI FUNCTIONS ABOUT THE MIDI IMPLEMENTATION The following MIDI messages can be transmitted and received from Nord Stage EX Note ON OFF Note On and Note Off messages are transmitted and received PITCH BEND Pitch Bend messages are transmitted and received by Nord Stage EX CONTROLLERS On the MIDI Menu see page 68 you can select if the Nord Stage should transmit and or receive Control Change messages f you have an Control Expression pedal connected to the ORGAN SWELL INPUT this is transmit ted and received as Controller 4 f you have an Control Expression pedal connected to the CONTROL PEDAL INPUT this is trans mitted and received as Controller 11 Expression By using the Morph function you can control most of Nord Stage EX s parameters with a Control pedal f you have a sustain pedal connected to the SUSTAIN PEDAL INPUT this is transmitted and received as Controller 64 Sustain Pedal f you have a sustain pedal connected to the ROTOR SPEED INPUT this is transmitted and received as Controller 90 Almost all other controls knobs and buttons on the front panel are also transmitted and received as Control Change messages This can be used to record your actions on the front panel into a MIDI sequencer
81. functionality can be achieved by double clicking a button This works pri marily with Keyboard Zone assignments and Effect source selects The SHIFT button is also an EXIT button for example when you want to exit a menu or cancel a Store operation VALUE DIAL PENDING PROG CHANGE The VALUE DIAL to the right of the DISPLAY is used to select Program locations to set system pa rameter values and to type in Program names When used with the SHIFT button the VALUE DIAL selects a Program but does not load it until you press the corresponding blinking PROGRAM button See Pending program change above Page 17 5 The Program section Overview Nord Stage EX v6 x THE STORE BUTTON The red STORE button is used when storing Programs see Storing Programs on page 20 PROGRAM BUTTONS Below the DISPLAY are the six PROGRAM buttons 1 6 They are used to load Programs to access menus and to load either of the two Organ Inits THE LivE 1 2 BUTTONS Pressing either of the LIVE 1 2 buttons will activate a Live buffer see About the Live 1 amp 2 Buffers on page 19 for a description of this special memory feature They are also used to load the Piano and Synth Inits KB ZONES 2 3 BUTTONS These buttons are used to activate keyboard zones Each Program can have up to three keyboard zones Lower Upper High and each instrument section can be set to play across all two or one of these zones see Keyboard Zones and
82. ge EX v6 x 9 The Morph Assign feature Morph Assignable parameters 5 Hold down the WHEEL button in the Morph Assign section again while turning the Instrument LEVEL knob that was set to minimum value in Step 2 up to maximum value 6 Release the WHEEL button in the Morph Assign section 7 When you now move the Wheel the Level is gradually lowered for one instrument and raised for the other instrument allowing you to morph between the two instruments If you double click a Morph button WHEEL A TOUCH or CTRLPEDAL it will stay active and you can assign any number of morphs without holding the Morph button When you have finished assign ing Morph parameters press EXIT SHIFT to exit This for example allows for one handed Morph assignments MORPH ASSIGNABLE PARAMETERS Basically you can use the Morph function to control all rotary encoders knobs that show parameter values with LEDs and the organ drawbars Apart from the number of assignable parameters there is no limit to how many parameters you can control simultaneously using Morph The following parameters can be Morph controlled The LEVEL knobs for all Instrument sections The TIMBRE knob in the Synth section The FILTER FREQUENCY knob in the Synth section The DRAWBARS in the Organ section The Effect RATE TEMPO knob The Effect AMOUNT knob The PARAMETER knob in the Extern section see page 64 The ROTOR SPEED button E g hold down the WHEEL bu
83. gram Mode ways globally or independently for each program When Glo bal is selected the Extern MIDI A amp B channels will be the same for all programs If Program is selected the Extern MIDI A amp B channel will be saved with each Stage EX program Extern MIDI A B Channel Extern MIDI A B Volume Extern MIDI A B Prog Change This sets the MIDI channel the Extern section should use The Extern section can send MIDI Volume messages 0 127 allowing you to control the level of the external device The Extern section can transmit MIDI Program Change mes sages 0 127 allowing you to change programs on external devices 1 16 14 default for Panel A 15 is default for Panel B Off Default 0 127 Off Default 1 128 Extern MIDI A B Bank Sel 00 This allows you to set a value for a MIDI Bank Select message on Control Change address 00 00 Off 0 127 Extern MIDI A B Bank Sel cc32 This allows you to set a value for a MIDI Bank Select message on Control Change address 32 cc32 Note that there are many different variations between instru ments in how Banks are numbered and accessed via MIDI Off Default 0 127 Extern MIDI A B CC Value This will transmit values for the selected MIDI CC number Off Default 1 127 Extern MIDI A B CC Number This decides which MIDI Controller number the Extern section should be transmitted when MIDI CC is activated MIDI CC 0
84. he respective note that each drawbar represents when C3 is our reference note right Register Voice Panel Name selector 1 Bass 16 BAS16 2 Strings 16 STR16 3 Flute 8 FLUTE8 4 Oboe 8 OBOE8 5 Trumpet 8 TRMP8 6 Strings 8 STR8 7 Flute 4 FLUTE4 8 Strings 4 STR4 9 A bright voice pitched an octave anda 2 2 3 fifth above the fundamental Note that the voices aren t supposed to replicate the instruments they are named after but rather to describe the basic tonal characteristic of the voice i e flute soft oboe reedy strings bright trum pet brassy Page 28 Nord Stage EX v6 x 6 The Instruments The Organ Section VIBRATO The F Type Model has two basic vibrato modes Light and Heavy with different rates for each mode Slow Fast rate for the Light mode is set with the V1 V2 Selectors and C 1 C2 sets the rate for Heavy mode Note that the F Type vibrato is common for both Panels if a dual manual organ is used SWELL CONTROL Swell is the characteristic volume function that you control from an organs pedal Swell is not only a volume control for the B3 it also changes the character of the sound in a special way To use Swell control on the Nord Stage EX simply plug in a standard expression pedal to the ORGAN SWELL input on the rear panel see Connecting pedals on page 11 and configure the pedal on the System Menu see page 66 A expression pedal connected to the ORGAN SWELL inp
85. iangle quilat ral est employ pour alerter l utilisateur de la pr sence d instructions importantes pour le fonctionnement et l entretien service dans le livret d instructions accompagnant l appareil Instructions pertaining to a risk of fire electric shock or injury to persons IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Warning When using electric products basic precautions should always be followed including the following 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments
86. im Bass EQ 84 AmpSim Mid EQ 85 AmpSim Treble EQ 86 Page 91 15 MIDI implementation MIDI Controller list Nord Stage EX v6 x Nord Stage Parameter MIDI Controller AmpSim Enable 87 Rotor Destination 88 Rotor Drive 89 Rotor Speed 90 Rotor Stop 91 Rotor Enable 92 Compressor Amount 93 Compressor Enable 94 Reverb Amount 95 Reverb Size 96 Reverb Enable 97 Organ Enable Sustain Pedal 98 Organ Octave Shift 99 Organ Level 100 Organ Enable 101 Organ KB Zone Assignment 102 Piano Enable PStick 103 Piano Enable Sustain Pedal 104 Piano Octave Shift 105 Piano Level 106 Piano Enable 107 Piano KB Zone Assignment 108 Synth Enable PStick 109 Synth Enable Sustain Pedal 110 Synth Octave Shift 111 Synth Level 112 Synth Enable 113 Synth KB Zone Assignment 114 Page 92 Nord Stage EX v6 x 15 MIDI implementation MIDI Implementation Chart MIDI IMPLEMENTATION CHART Model Clavia Nord Stage EX Eighty Eight Seventy Six Compact OS v4 x Date 2008 12 09 Function Transmitted Recognized Remarks MIDI Channels 1 16 1 16 Individual channels for Panel A and B Velocity Yes Yes Incoming Velocity data ignored for Note On Off Organ Release velocity sent but not received Aftertouch Yes Yes Channel aftertouch only Pitch Bend Yes Yes Control Change Yes Yes See MIDI Controller list on page 90 Program Change Yes Yes 0 125 126 L
87. ing dialogue 2 Click on the Bank Up tool or select the File Bank Upload menu command Ctrl Shift U Verify that the source bank is correct and browse to the desired destination folder on the computer hard drive Bank Upload Source Partition Bank Program Page 1 6 sounds v Destination Folder Piano Choose Folder Create subfolders You can also select All at the bottom of the bank list drop down This will upload the entire content of the partition to the computer hard drive If the Create Subfolders option is checked a folder structure partition bank sounds will automat ically be created in the destination folder Page 77 13 Nord Sound Manager The Quick Tour Nord Stage EX v6 x DOWNLOAD A COMPLETE BANK OF SOUNDS FROM THE HARD DRIVE TO THE STAGE 1 Click on the Bank Down tool or select the File Bank Download menu command Ctrl Shift D 2 Verify that the destination bank is correct and browse to the desired source folder on the compu ter hard drive Bank Download Source ANew FolderlPiano Search subfolders Destination Partition Bank Piano v All 9 sounds Download Cancel Note When you click on Download a dialogue appears to inform you that the content of the desti nation bank in the Nord Stage will be replaced with that of the source file If you select All in the destination bank drop down you can replace all the sounds in a partition with tho
88. ip Backing up from the Nord Sound Manager is done in an incremental manner Unless you change the name or the location of the back up file only the content that have been changed since the previous backup will be saved RESTORE To restore a previously saved backup file to the Stage EX select this option and browse to a backup file on the hard drive file extension nsb and click Open Important The restore function will begin after you have clicked Open and confirmed your inten tions in the dialogue All the content of a connected Nord Stage will then be irrevocably replaced by the content of the backup file The Nord Stage EX memory has twice the capacity of the Nord Stage classic This means that a backup from a Stage EX may not fit in a classic Stage if this backup exceeds the available memory capacity in the classic Stage Page 80 Nord Stage EX v6 x 13 Nord Sound Manager Nord Sound Manager reference MENUS In the Nord Sound Manager the usual Windows and Mac OSX keyboard commands can be used The menus can be accessed by pressing the Alt key and the underlined letter in the menu bar Most of the commands can also be accessed by pressing the Ctrl on the Mac Command key to gether with the letter shown next to the command name in the menus FILE Edit View Help Sound Upload Ctrl U Sound Download Ctrl D Bank Upload Ctrl Shift U Bank Download Ctrl Shift D Backup Ctrl B Restore Ctrl R Clean Del
89. ir own drawbar Vibrato on off and Percussion on off settings Page 29 6 The Instruments The Piano section Nord Stage EX v6 x THE PIANO SECTION CLAVEG BRILL TREB SI MEDIUM Orr KB ZONE SELECT OCTAVE SHIFT PSTICK SUSTPED PIANO SELECT CLAV HPS A GRAND WURL A UPRIGHT E PIANO E GRAND DYNAMICS The Piano section of Nord Stage EX contains six Piano Categories and each Category can contain different instrument Types You can freely add new piano instruments via USB using the Nord Sound Manager utility see Nord Sound Manager on page 72 Right out of the box Nord Stage EX features a fine collection of carefully selected acoustic and elec tromechanical pianos A lot of effort was put in to ensure that the play response and sound of the sam pled instruments matches every nuance of the real article Each piano instrument has been multi sampled in a vast amount of velocity levels That s one reason why they all sound and feel so authen tic ABOUT THE PIANO INSTRUMENTS Since all piano samples are stored in Flash memory you can easily add and or replace the stored piano instruments with new ones supplied free from Clavia The size of the available memory for the piano samples is approx 256 MB When you download Piano instruments these will always automatically be loaded into the corre sponding Category A Program saves Piano instruments by Category and the Type number If a Pr
90. ive1 127 Live 2 System Exclusive Yes Yes See the MIDI Implementation section Page 93 15 MIDI implementation MIDI Implementation Chart Nord Stage EX v6 x Page 94 Nord Stage EX v6 x INDEX NUMERICS 2nd 3rd Organ Percussion 25 A Aftertouch 62 Amp Envelope Attack 43 Amp Envelope Synth 43 Ampsim EQ 53 Attack Amp Envelope 43 Mod Envelope 41 Audio Routing Mode 66 Auto Glide mode 47 Auto Wah modulation 52 B 3 Organ 24 Bank Selecting 12 Buttons About 9 C1 C3 Organ Chorus 26 Chorus effect 52 Chorus organ 26 Clav EQ Piano section 33 Compressor 54 Connections Audio 10 MIDI 10 Pedals 11 Control pedal Connecting 11 Technical requirements 11 Controllers dump 76 List MIDI 78 MIDI transmission and reception 74 Ctrl Pedal Type 67 Index D Decay Release Amp Envelope 43 Mod Envelope 42 Display 17 Drawbars B 3 24 Drawbars V type organ 27 Dual KB 59 Dual Panel setups 58 Dump Program source 69 Dump Program Source 69 E Editing Programs 13 Effects section 49 Env Mode 43 Env Vel Amp Envelope Synth 43 Mod Envelope Synth 42 EQ Synth 47 Ernie Ball control pedals 67 Expression pedal Technical requirements 11 Extern Section About 63 Setting up 63 Using 63 F Factory presets 71 Restoring 71 Factory Reset 68 Fast Rotary Speaker 55 Fatar control pedals 67 Fender Twin 54 Filter KBT Keyboard Tracking 45 Reson
91. ividual random contact bounces for each harmonic Modeling of the unique frequency characteristics of the built in pre amplifier which forms the body of the B3 sound Simulation of the energy robbing on the tone wheels that results in the typical compressed sound Authentic tuning of the tone wheels according to the original B3 design Extremely fast keyboard response Full polyphony THE DRAWBARS The drawbars of Nord Stage EX are represented by buttons and LED chain graphs instead of ordinary mechanical drawbars This gives you a big advantage when you change preset or Programs the cor rect drawbar settings are recalled immediately and shown by the LEDs In other words no need for the regular and error method It s very easy to get the hang of changing the drawbar settings in a natural way with the buttons Page 24 Nord Stage EX v6 x 6 The Instruments The Organ Section The drawbars of Nord Stage EX SUB SUB3 FUND 2ND 3RD 4TH 5TH 6TH 8TH behave similar to their mechani cal counterparts i e you pull out the drawbars by pressing the LOWER DRAWBAR buttons on x and push them back in by ele D pressing UPPER DRAWBAR ele 1 Ile buttons The DRAWBAR buttons are special in the way that they auto increment decrement the drawbar value when held Le if you hold a DRAWBAR button the corresponding drawbar value will continue to increment or decrement within its range
92. k but you may choose another partition and bank if you wish Click on the Choose Folder button to select the destination on the hard drive If the Create Subfolders option is checked a folder structure partition bank sounds will automat ically be created in the destination folder Note If a folder with the same name as the source partition bank already exists in the location on the hard drive this folders entire content will be replaced by the uploaded files from the Nord Stage BANK DOWN This function will download an entire bank of pianos programs or synth patches from the computer hard drive to the Nord Stage The default destination will be the currently active bank but you may choose another partition and bank if you wish Click on the Choose Folder button to select the source on the hard drive Note The destination bank in the Stage will be replaced by the content of the source folder BACKUP This will make a backup of all the pianos programs and synth patches in the Nord Stage EX The file that is created on the hard drive will have the extension nsb Backing up the entire memory content in this manner will take some time depending on the amount of pianos in the Nord Stage The Nord Sound Manager will suggest a location for the backup the first time this function is activated in My Documents Nord Sound Manager files If you rather save the backup file elsewhere use the file browser dialog to pick another location T
93. l instrument organizes programs in Banks there is an option to send Bank Change mes sages on the Extern Menu page see Extern menu on page 70 Page 64 Nord Stage EX v6 x 10 The Extern section The Parameter section MIDI CG This allows you send MIDI Control Change messages to control a parameter of your choice on the external instrument You first have to decide which Controller number the PARAMETER rotary en coder should send value changes for This is done on the Extern Menu 1 Press SHIFT and the EXTERN button to access the Extern menu 2 Use the PAGE buttons to select the Extern MIDI CC Number menu page 3 Use the VALUE DIAL to select a MIDI CC Number 0 119 You may want to check the manual for the external instrument to see which parameters are assigned to which CC numbers 4 Press the ExiT SHIFT button briefly to exit If you now activate the MIDI CC button in the Parameter Select section you can control the selected external parameter using the PARAMETER rotary encoder in the Extern section You can turn this off on the Extern menu see Extern menu on page 70 The external instrument may have to be set to receive MIDI CC messages for this to function ABOUT SEND ON LOAD You can set whether Program Change Volume and MIDI CC messages are sent out when you load a Program in Nord Stage EX If you do not want this to occur make sure Send On Load is set to Off on the Extern menu Page 65
94. l organ is used F TYPE MODEL FARFISA The typical buzzy sound of the Farfisa organ is one of the most distinct and easily recognizable keyboard sounds ever created yet it is actually possible to get quite a wide range of sounds out of the instrument For the Nord Stage EX a Farfisa Compact DeLuxe was used as the source model Page 27 6 The Instruments The Organ Section THE REGISTER SELECTORS The drawbars act as on off switches or Register selectors when the F Type model is se lected Instead of drawbars the original Farfisa organs featured rocker type switches to select instrument voices actually different filter settings in vari ous footage octave ranges In Nord Stage EX this functionali ty 1s reproduced When the F Type organ model is selected the LOWER DRAWBAR buttons are used to turn voices on and the HIGHER DRAWBAR buttons turns them off The drawbar LEDs 5 8 are lit up for an acti vated voice and drawbar LEDs 1 4 are lit up for a deactivated voice The available voices for the F type also printed on the panel directly over the draw bars are as follows from left to Nord Stage EX v6 x D suB3 FUND 2ND OD DO 1 1 Ve C3 In the illustration above we have chosen C3 as our reference note The four Register selectors correspond to the fundamental harmonic but with different tonal characteristics The arrows point at t
95. l the rate and amount of panning with the RATE TEMPO and AMOUNT knobs The Pan effect is stereo in out STATIC PAN CONTROL OF AN INSTRUMENT Sometimes you may want absolute manual control of over the panning of an instrument This can be done with the A Pan effect as follows Enable Effect 1 for the instrument you want to pan and select the A Pan effect type Set the RATE TEMPO KNOB to zero Then you can place the instrument anywhere in the stereo field manually with the AMOUNT knob just like a pan control on a mixer WAH WAH The Wah Wah modulation is often used for electric guitars to get that characteristic talking guitar sound Wah Wah can also be extremely useful on electric piano sounds Try out the Clavinet sound Page 51 7 The Effects The Panel effects Nord Stage EX v6 x with Wah Wah modulation and you ll understand Basically the Wah Wah modulation is a lowpass type of filter that can be swept across the frequency range During the sweep the filter s characteris tics also changes The Wah effect is mono in out For the Wah Wahl modulation you control the pedal position with the RATE TEMPO knob and the wet dry mix with the AMOUNT knob If you use an expression pedal connected to the CONTROL PEDAL INPUT you can control the filter sweep and thus the Wah Wah effect from the pedal by using the Morph function see page 60 A WHA 1 amp 2 AuTO WAH Auto Wah 1 2 are variations of the Wah Wah effect described abov
96. ly brighter char acter Stage soft A reverb with a medium decay time and mellow character Stage 2 A medium decay reverb with slightly brighter character Room Room ambiance with a rather short decay time The DRY WET knob sets the balance between the unprocessed and the processed signal Page 54 Nord Stage EX v6 x 7 The Effects The Rotor section THE ROTOR SECTION The Rotor effect rotary speaker simulation in Nord Stage EX accurately repro duces the sound of the rotating horn and bass rotor as well as the characteristics of the built in amplifier of the original Leslie units The Rotor effect is mono in Stereo out DRIVE You activate or deactivate the Rotor effect for a selected instrument in the same ORG PIANO SYNT way as Panel Effects see Activating Panel effects on page 50 NE You switch between fast and slow rotor speeds by pressing the SPEED button 3 SOURCE STOP To stop the rotors press the STOP button this does not deactivate the Rotary Speaker simulation it only stops the rotors When you press the STOP button again the rotors will accelerate to the Slow Speed setting The Rotor acceleration rate 1 e time it takes to go from slow to fast and SPEED vice versa can be adjusted on the Sound menu see Sound Menu on page 68 The DRIVE knob controls amount of overdrive This simulates pre amp overdrive effect of the original Leslies By
97. m The TIMBRE knob does not have any effect on the sawtooth wave Page 36 Nord Stage EX v6 x 6 The Instruments The Synth section PULSE The pulse wave contains only odd numbered harmonics 3 5 7 etc at 50 pulse width square wave This waveform is special in that its harmonic content can be varied continuously by adjusting the pulse width PWM Amplitude Amplitude Time gt Harmonic number 10 20 30 40 Frequency The pure square wave a pulse The frequency spectrum of a pure square wave The wave with 50 pulse width signal contains only odd harmonics Amplitude Amplitude gt gt Harmonic number 10 20 30 40 Frequency The pulse wave at 10 pulse The frequency spectrum at 10 pulse width Now width also even harmonics are gradually introduced mak ing the sound sharper but also thinner Amplitude Amplitude ts uD Vita cut x Harmonic number 10 20 30 40 Frequency The pulse wave at 5 pulse width The narrower the pulse width the more harmonics are present in the frequency spectrum The TIMBRE knob controls the pulse width of the pulse wave from 50 square wave to 99 You can modulate the Timbre using Morph see page 60 Velocity or Mod Envelope This waveform is suitable for many type of sounds and has a more hollow character than the Sawtooth wave PULSE FIXED TIME A normal pulse wave has a pulse width adjusted relativ
98. n dual panel mode you are basically layering two full sets of the Nord Stage EX panel You activate both panels by holding down one of the PANEL A B buttons and then pressing the other To exit Dual Panel mode hold down one of the PANEL A B buttons and then press the other To copy the settings from another Panel to the active Program Panel press and hold one of the Panel buttons and turn the Value dial The display will indicate which of the Panels in the entire Program memory of the Stage that will be copied to the current Program Panel Don t forget to save any new Panel combination that you have created using this method if you want to keep it ABOUT PANEL EDIT FOCUS PANEL A 9 PANEL B DUMP ONE 9 DUAL KB Both Panels activated One of the PANEL button LEDs will blink to indicate which Panel is currently has the edit focus If both Panels are activated the settings on the front panel always reflects settings for one of the Pan els A or B at a time Any tweaking of parameters will only affect the Panel that has edit focus which is indicated by a blinking PANEL button f you select pianos to both Panels they can be detuned by using the Unison Detune feature Pressing the other PANEL button will then instantly switch edit focus to the other Panel and allow you to edit the settings Each Panel contains independent settings for the Organ separate instances of two instruments Piano and
99. n out some are stereo in out and others are mono in stereo out For each individual effect the channel configuration is stated in the related text The internal routing of some effects means that the instrument level has to be taken into account Whenever this applies it will also be explained in the corresponding effect description Page 49 7 The Effects The Panel effects Nord Stage EX v6 x THE PANEL EFFECTS EFFECTS EQ FOCUS RATE TEMPO 4 gt AMOUNT EFFECT 1 EFFECT 2 DELAY WA WA FLANG1 FLANG2 1 A WA1 PHAS2 CHOR1 FEEDBACK A WA2 1 CHOR2 PING PONG TAP TEMPO BASS ORG PIANO SYNT ORG PIANO SYNT ORG PIANO SYNT ORG PIANO SYNT d 1 l jJ SOURCE SOURCE SOURCE SOURCE ACTIVATING PANEL EFFECTS To enable a panel effect press the ON OFF button at the bottom of the corresponding effect section The LEDs above the button will indicate which instrument the effect is assigned to Hold down SHIFT and press the SOURCE button to change the instrument assignment You can also step through the instrument assignments by double clicking the SOURCE button This is convenient when you only have one hand free and cannot reach the SHIFT button MAKING SETTINGS FOR PANEL EFFECTS EFFECTS SECTION To make settings for individual effects in the main Effects section Effect 1 Effect 2 Delay you mainly use the RATE TEMPO and AMOUNT knobs Which parameters these two knobs control de pend o
100. n the selected effect these are described for the corresponding effects below The RATE TEMPO and AMOUNT knobs can also be Morph controlled see page 60 ABOUT THE FOCUS BUTTON If you have more than one effect activated in the Effects section e g Effect 1 and Effect 2 The FOCUS button is used to select which effect s settings Rate Tempo and Amount you currently see and can edit Pressing the Focus button will alternate focus between the currently activated effects The LED beside the corresponding Effect 1 Effect 2 Delay section is lit for the edit active effect EFFECT TYPE SELECTION WHEN AN EFFECT IS OFF When an effect is off you can still check which effect type is selected by pressing the corresponding Selector button once The Selector LED will briefly show the current effect type If you press the Se lector button repeatedly you change the Effect type without turning on the effect In this way you can make sure that the right effect type is selected before it is turned on This feature is available for the Effect 1 amp 2 type Amp simulation model and Reverb type selectors You can also adjust the effect settings even if the actual effect is turned off The values of the param eters will be shown in the display Page 50 Nord Stage EX v6 x 7 The Effects The Panel effects EFFECT 1 EFFECT 1 The Effect 1 section offers six different types of modulation Use the SELECTOR button to switch between the available
101. nd you want choose from the different combinations available and you have many interesting FM sounds at your disposal When a new wave is selected the MAIN DISPLAY shows for a short dura tion the algorithm together with information on the frequency relations between the operators and whether feedback is used The WAVE DISPLAY shows the modulator s frequency relation to the car rier If an operator uses feedback it is indicated by a dot next to the digit In the chart below all avail able algorithms together with the notation used in the WAVE DISPLAY are listed Wave disp Algorithm Freq relation Cr 1 op with feedback 1 1 2 op 1 1 2 2 op 2 1 3 2 op 3 1 5 2 op 5 1 9 2 op 9 1 1 2 op with feedback 1 1 2 2 op with feedback 2 1 3 2 op with feedback 3 1 5 2 op with feedback 5 1 9 2 op with feedback 9 1 11 3 op 1 1 1 21 2 1 1 31 3 1 1 51 5 1 1 91 9 1 1 Page 40 Nord Stage EX v6 x 6 The Instruments The Synth section Wave disp Algorithm Freq relation 22 3 op 2 2 1 42 4 2 1 82 8 2 1 1 1 3 op with feedback 1 1 1 1 2 3 with feedback 1 2 1 1 3 3 op with feedback 1 3 1 1 5 3 op with feedback 1 5 1 1 9 3 op with feedback 1 9 1 1 F 3 op with feedback 1 1 2 2 F 3 op with feedback 2 1 2 3 F 3 op with feedback 3 1 2 5 F 3 op with feedback 5 1 2 9 3 op with feedback 9
102. nsuassasuuenmuauassanunasunansecuuecesesecs 1 AUDIO CONNECTIONS zssaRssRsssusa asrsa Rara AER rCRa MERE MEA MEE Masa MIDI CONNECTIONS D LJ CONNECTING PEDALS as 4 GETTING STARTED i ace ABOUT INSTRUMENTS aa Rena a MAMMA aA 22 AB GUT PROGRAM 8S iiuorcsesssshuRR REA ERE MRRE EE ERE E EE MR MEME EM a ACTIVATING INSTRUMENT SECTIONS ABOUT PANEL JA Se El 02002222 2525 c0lascaRadbasiElORRR RR RREM M kae DB Ep SETTING OUTPUT LEVEL FOR INSTRUMENTS sssssssussssussuussusssassuass 72 ADDING GLOBAL raien an ianen nA RAM aaraa D D Es THE PROGRAM SECTION 1 6 EJVERWVIEWis isissssassnaE Rui WHAT IS PROGRAM n a D STORING PROGRAMS ERRARE AERESESANREEERRRPERARRASRNEEERRE NM RES NEM MEE d 6 THE INSTRUMENTS r
103. ntent in this manner will take some time depending on the sizes of the samples Tip Backing up from the Nord Sound Manager is done in an incremental manner Unless you change the name or the location of the back up file only the samples and or programs patches that have been changed since the previous backup will be saved RESTORE GTRL R To restore a previously saved backup file to the Stage select this option and browse to a backup file on the hard drive file extension nsb and click Open Important The restore function will begin after you have clicked Open and confirmed your in tentions in the dialogue All the content of a connected Nord Stage will then be irrevocably re placed by the content of the backup file GLEAN DELETED SPACE This function will clean up the space where any previously deleted pianos programs or synth patches have been This is done in order to make this deleted memory space available to new additions Note Cleaning is automatically done if you download a new piano program or synth patch to the Nord Stage but this menu command makes it possible to manually start the cleaning process FORMAT This is a radical function it will format the entire partition that is in focus All the sound in the par tition will be deleted You will be asked to confirm your intentions Exit CTRL Q Exits the Nord Sound Manager application EDIT View Help Rename Ctrl N Delete Del Select All Invert S
104. nussnassuaususunaouuensas 61 ABOUT SETTING MORPH PARAMETER RANGES sssssssssussuassuusssussuuuus 62 CLEARING MORPH ASSIGNMENT S ssssssssunusuassuassuaunassnassuaunacsnaonuasus 62 ABOUT APTERTOUGCH RR PRAES MESE NER 62 ABOUT THE EXTERN SECTION 63 SETTING cerciaccaeccdeiaasecsseiiiidnwiascesces RI RNERES NE SMS conse 63 USING THE EXTERN SECTION lt lt ERRARE EAE RE 63 THE PARAMETER SEGCTICIN rpn enna 64 1 15 SYSTEM FUNCTIONS OCG SYSTEM Eu Ti LU EE III IL ICI GLILLLLSUIII I ILI II 66 S GUND MENU i seran EFRREFREMPEREFRREREERNERERAERMMUNRARENE ARMEN EAERAEERANARATERSUEEE MN 68 MPD MENE ais ceux Saa RR MAE UREREMKESESNMESFCENEEER EEEE ERES Renee NEEREEENRENREENSS MEME 68 EXTERN NR UPESEREEPFANSRRAPEUERS 70 Nord Stage EX v6 x Table of contents 1 Za FACTORY PRESETS AND os ESSE E INTERNAL RES REESE NALE QR NES 71 FACTORY PRESETSI L2 ssa s RcRSEEEMEEENEEEBNEEUEEEGEERMENN
105. ogram refers to a Piano instrument that isn t currently loaded i e an empty Type slot the Type display will blink showing the missing Type number If this happens you can either navigate to another instrument Type in the selected Category and select to use this instead or use the Nord Sound Manager utility to down load an instrument into the empty Type location Page 30 Nord Stage EX v6 x SELECTING PIANO INSTRUMENTS PIANO SELECT TYPE DYN CLAV HPS A GRAND WURL A UPRIGHT E PIANO E GRAND 9 INFO DYNAMICS 6 The Instruments The Piano section You use the SELECTOR button to select an instrument category and then use the TYPE button to select a specific instrument or variation within the selected category Category Description A GRAND Acoustic grand pianos A UPRIGHT Acoustic upright pianos E GRAND Electric grand pianos E PIANO Electric Pianos WURL Wurlitzer electric pianos CLAV HPS Clavinets and Harpsichords ABOUT THE FACTORY SOUND LIBRARY As mentioned previously the Piano section is open ended which means that you can load new or im proved instruments using the Nord Sound Manager utility Here is a description of the pianos that are included with the Nord Stage EX when it left the Nord factory Category Type Description A Grand 1 Grand Lady D StwD Med The Grand Lady D is a carefully voiced German Model D that has been carefully selected by us because of its speci
106. om of the window indicates how much memory is being used in the selected partition The red area shows the used memory green indicates space that is available for new sounds RIGHT CLICKING If you right click on a sound a context menu will provide the following options Page 73 13 Nord Sound Manager Overview Nord Stage EX v6 x Select In Instrument Upload Download Rename Delete SELECT IN INSTRUMENT This will select the chosen sound in the Manager list to be instantly accessible on the Nord Stage UPLOAD This will upload the selected sound from the Nord Stage to the computer hard drive in a folder of your choice DOWNLOAD This is only available if you right click on an empty location that does not contain a sound This al lows you to choose a file on the hard drive to be downloaded to the location in the Nord Stage EX Note When a Nord Stage EX leaves the factory every program or synth location is filled with patch es You need to use the Delete function to get any empty locations which are displayed without any characters in their name RENAME This allows you to rename a Program or a Synth patch Characters supported are a z A Z 0 9 and a hyphen and the name can contain up to 16 characters Any other characters will not be displayed in the Sound Manager lists or in the Stage display Pianos cannot be renamed this option will not be available if you right click on a Piano DELETE This will del
107. on the second value CLEARING MORPH ASSIGNMENTS To clear Morph Assignments press SHIFT and the corresponding button in the Morph Assign section that stores the assignments that you wish to clear To remove an individual parameter hold down the MORPH ASSIGN button that the parameter is as signed to The current range will be shown by the rotary encoder LEDs for the parameter Move the rotary encoder until both LEDs go off to erase the Morph assignment ABOUT AFTERTOUCH We have previously used the Wheel as an example controller but you can also use Aftertouch to Morph control parameters The Nord Stage EX keyboard can respond in two ways to how you play The first is velocity not applicable for organ sounds or Morph which means that the faster the player presses a key down the higher the velocity value Once a key is played and held down there is also Aftertouch some times called channel pressure The player can apply more pressure on a key while it is down and this will generate a signal that can be used to control parameters Applying Aftertouch to one key will affect the sound of all sounding notes of the instrument Page 62 Nord Stage EX v6 x 10 The Extern section About the Extern section 10 THE EXTERN SECTION ABOUT THE EXTERN SECTION EXTERN When developing Nord Stage EX Clavia aimed to make external control an inte grated feature of instrument where all essential external MIDI control functions
108. ontrol Synth Vibrato which is set using 8 lt ms the SELECTOR button in the Vibrato section ATOUCH f Aftertouch A Touch is selected you can control the vibrato by pressing down held notes on the keyboard See About Aftertouch on page 62 ERE You can also control vibrato using the Mod Wheel There are also three delay Dly 1 3 modes which automatically activates vibrato after a certain time for held notes The difference between the three delay modes is the time it takes for vibrato to activate Dly1 is the fastest time and Dly3 the slowest The basic Delayed Vibrato depth and speed settings are set globally on the Sound Page see Sound Menu on page 68 EQ The Synth also features a basic 2 band EQ section This allows you to quickly boost or cut treble and bass frequencies by 15 dB Turn the TREBLE or BASS knob clockwise from center position to boost the re spective frequency band and vice versa A LED indicates when the EQ is ti BASS TREBLE active ACTIVE ACTIVE SOUND SELECT SECTION When you save a Program the current Synth settings are of course stored together with all other panel settings but the Sound Select section allows you to select store Synth sounds separately from Pro grams in this way you can build up a library of favourite synth sounds to access whenever you need them Page 47 6 The Instruments The Synth section Nord Stage EX v6 x SELECTING SYNTH SOUNDS The av
109. oom using the Selector button How to use the other effects is described in the Effects chapter see The Effects on page 49 Page 15 5 The Program section Overview Nord Stage EX v6 x 5 IHE PROGRAM SECTION MORPH ASSIGN CURSOR STORE PAGE 9151259 ele DEL INS JA WHEEL A TOUCH CTRLPED m CLEAR MORPH eee STORE AS PENDING PROG CHANGE PROGRAM KB ZONES mmm 0 f SYSTEM SOUND MIDI EXTERN 95 6 9 LIVE 1 LIVE 2 SETLO SET HI m SPLIT SPLIT SHIFT OVERVIEW The Program section comprises central functions such as Program handling system pages etc Sys tem pages are covered in a separate chapter see System functions on page 66 LOAD A PROGRAM You can load a program in several different ways Press any of the PROGRAM 1 6 buttons to load the corresponding program from the current Pro gram Page Press or hold PAGE or to step through the 21 Program Pages in the Nord Stage Turn the VALUE DIAL in either direction to scroll through all Programs Program Page focus is shifted as needed Hold SHIFT and press or hold the PAGE buttons to step through the Programs Program Page focus is shifted as needed Press either of the LIVE 1 2 buttons to activate one of the special Live Buffers see About the Live 1 amp 2 Buffers on page 19 Page 16 Nord Stage EX v6 x 5 The Program section Overview PENDING PROGRAM CHANGE Normally
110. ost front panel section contains a Master Level control and a rotary speaker simulator effect The MASTER LEVEL knob controls the overall output level for all four CH OUT jacks and the HEAD PHONES output The Rotor effect section is logically placed close to the organ section as rotary speaker effects are most commonly used with organ sounds but can be applied to any instrument section just like the other effects See The Rotor section on page 55 THE ORGAN SECTION The Organ section in the Stage features emulations of three classic organ models a Hammond B3 a Vox Continental II V Type and a Farfisa Compact DeLuxe F Type See The Organ Section on page 24 THE PIANO SECTION The piano section in Nord Stage EX comprises various multi sampled piano instruments The Nord Stage EX utilizes advanced multi level sample playback catching every nuance from soft to hard key strokes Nord Stage comes right out of the box with several classic piano instruments stored in a Flash memory with a total capacity of 256 MB The big advantage with Flash memory is that you can re place instruments with new ones and that no backup battery is required The Stage also sports a USB interface for quick and easy download of new piano sounds See The Piano section on page 30 Page 7 2 Overview The Keyboard Nord Stage EX v6 x THE SYNTH SECTION The Synth section has been designed for maximum ease of use in live situations while keeping
111. ping the Nord Stage was to create a flagship stage instrument encompass ing the whole range of Clavia s expertise Building on the success of the Nord Electro the Nord Stage incorporates the best emulations of traditional electromechanical acoustic keyboard instruments on the market as well as a synthesizer section designed for maximum ease of use yet offering wide sonic possibilities The Nord Stage EX features outstanding classic keyboard sounds with true feel from natural key board response to authentic sound A medium weighted hammer action 88 76 note keyboard or a 73 note semi weighted waterfall keyboard makes this instrument the largest in Clavia s range yet it weighs only 18 5 16 5 9 7 kilos which is an achievement in itself To make a great tool you have to put all the focus on a few things and that s what we did with the Nord Stage Think about it the best tool isn t a Swiss army knife FEATURES The Nord Stage EX has the following main features Organ section with faithful reproductions of three classic models B3 Hammond V Type Vox Continental and F Type Farfisa Piano section with concert grand upright acoustic pianos Electric Pianos and Wurlitzer electric pianos Clavinet and Electric Grand The total memory capacity in the Stage EX units is 256 MB The available space for the pianos is a bit smaller part of the memory is used for the wavetables e Synth section with subtractive FM and wavetable synthesi
112. plugging in a sustain pedal or a foot switch to the ROTOR SPEED PEDAL input you can control the Rotor speed see Using a Rotor Speed pedal on page 11 The Rotor Speed can also be Morph controlled see page 60 ABOUT THE ROTOR EFFECT S INTERNAL ROUTING The Rotor effect is internally placed after the panel effects in Nord Stage EX It also sums signals if both Panel A and B are active This means that if you are using a split organ setup for example both manuals will be affected by the Rotor just like on the real thing Note also that the Rotor Drive parameter is dependent on the processed instrument s Level setting If the instrument being processed by the Rotor uses a very low level setting the amount of available drive will be significantly reduced Again this is very much like it works with the real articles when you increase the organ level e g by using a swell pedal the amount of distortion from the Rotor effect increases Page 55 8 Keyboard Zones and Dual Panel setups Keyboard Zones Nord Stage EX v6 x KEYBOARD ZONES AND DUAL PANEL SETUPS KEYBOARD ZONES You can split the Nord Stage EX keyboard in up to three Keyboard Zones Lower LO Upper UP and High HI You can then assign any of the Instrument sections to any or all of these zones An instrument can also be assigned to no keyboard zone at all which is useful when you want to play it from an external keyboard or from a sequencer
113. point for Zone 3 When using two zones the split point is set with the SET LO SPLIT button Keyboard Zone split points are shared between Panel A and B LAYERING INSTRUMENTS When two or three instruments are assigned the same keyboard zones they re layered i e play at the same time You can freely select which instrument s should play in each Zone e g you could have a piano assigned on its own to the Upper Zone but have piano layered with organ in the Hi Zone Another way to layer instruments is to activate both panels simultaneously see Dual Panel setups below Page 57 8 Keyboard Zones and Dual Panel setups Octave Shift Nord Stage EX v6 x OCTAVE SHIFT Each Instrument section and the Extern section have two OCTAVE SHIFT buttons which can be used to transpose the notes up or down in octave steps within the total note range of the instrument Each instrument in Nord Stage EX has a finite note range The Organ extends one octave below and one octave above an 88 note keyboard range The Piano extends one octave below the 88 key range but not above The Synth extends one octave in either direction just like the Organ You cannot transpose an instrument so that non existing notes would end up in the current Keyboard Zone Thus when playing over the whole keyboard you can only transpose a maximum of one octave up or down But when you are using splits e g so that a piano is set to play in a Zone with a range of
114. pos sible original Clavinet D6 sound variations plus an additional four by select ing different pick up and filter combinations Here s how it works MEDIUM EQ SOFT The two CLAV EQ buttons works as filter selectors By selecting different combinations of the BRILLIANT TREBLE and MEDIUM SOFT filter buttons you can reproduce all 15 possible filter variations exactly like on the original D6 PICK UP TYPE A Clavinet D6 has two separate pick ups one on the neck and one on the bridge By selecting either one pick up or both in different combinations you can alter the character of the sound quite drastically When the Clavinet is selected in the Nord Stage EX you use the TYPE button in the Piano Select section to select pick up variations according to the table below Pick up Type Description A CA Only the neck pick up a warmer less bright sound B CB Only the bridge pick up a bright sound C DA Both pick ups on and in phase a very full sound D DB Both pick ups 180 degrees out of phase the fundamental is almost cancelled out and the sound becomes thin DYNAMICS VELOGITY SENSITIVITY Some of the piano instruments sampled for the Nord Stage EX have very wide dynamic ranges by nature and naturally we wanted to capture this as accurately as possible Therefore it could be perceived that it is a little hard to reach the most extreme levels when playing the Nor
115. r is per fect or behaves the same They all differ in their frequency response and re spond differently to e g transients high gain and load This characteristic response and sound character of various amplifiers and speaker cabinets is often a desired effect that gives an organic quality to a too clean and perfect sound The special behaviour of an amplifier speaker combination when pushed to its limit overdrive has been exploited by musicians for decades The Ampsim models faithfully reproduces the overdrive response of different amplifier cabinet combinations lending you sound that authentic feel When no Amp Model is selected the Ampsim EQ section provides a more neutral EQ and overdrive BASS The Ampsim EQ effect is mono in out ORG PIANO SYNT DRIVE on The DRIVE knob controls the amount of overdrive for the Ampsim section SIUE If the DRIVE LED is on it indicates that overdrive is active EQ SECTION This is a 3 band equalizer which features controls for bass midrange and treble When there is no amp modelling the EQ operates like a standard mixer EQ with 15 dB boost cut for each band When amp modelling is used boosting and or cutting will produce different tonal characteristics de pending the selected amp model Page 53 7 The Effects The Panel effects Nord Stage EX v6 x AMP MODEL You select a type of amplifier speaker simulation using the SELECTOR button in the Amp Model sec tion There
116. re on the keyboard you play when KB TRACK is activated Frequency Imm RESONANGE The Resonance parameter is used to further adjust the characteristics of the Filter Increasing the Res onance will emphasize frequencies around the set Filter Frequency cutoff frequency making the sound thinner Further raising the Resonance will make the sound resonant to a point where the filter starts to self oscillate and produce a ringing pitch Exactly where in the frequency spectrum this ringing occurs depends on the Frequency value Amplitude 4 The figure shows a 24 dB lowpass filter with different resonance amounts Q values gt Frequency Cutoff frequency Page 45 6 The Instruments The Synth section Nord Stage EX v6 x FREQUENCY CONTROL This knob governs the amount of modulation applied to the Filter Frequency The Filter Frequency can be controlled by Velocity or the Mod Envelope The FREQ CONTROL knob controls the modu lation Amount for both modes VELOCITY If you turn the FREQ CONTROL knob clockwise the filter frequency cutoff will be raised if you play harder MOD ENv If you press SHIFT and turn the FREQ CONTROL knob so that the MoD LED lights up the filter frequency will instead be modulated by the Mod Envelope see Envelope on page 41 VOICES SECTION VOICES 10 1 DUAL L MULTI 3 7 a MONO a LEGATO S ie 10 FF 10 Ol GL
117. rought in by the UNISON knob in he Voices section see page 46 You can in fact have up to nine oscillators per voice without losing polyphony This allows for some really thick sounds TIMBRE The central TIMBRE control is used to shape the sound in various ways depending on waveform and algorithm see below Timbre can be Morph controlled allowing wheel aftertouch or pedal control over the sound For some algorithms the TIMBRE knob is disabled TIMBRE CONTROL This knob governs the amount of modulation applied to the Timbre parameter The Timbre parameter can be modulated by Velocity or the Mod Envelope indicated by the ENV MoD LED below the knob VELOGITY If the ENV Mop LED is dark Timbre will be modulated by velocity If you turn the TIMBRE CON TROL knob clockwise the Timbre parameter will be raised if you play harder If you press SHIFT and turn the TIMBRE CONTROL knob so that the MOD ENV LED lights up Timbre parameter will instead be modulated by the Mod Envelope see page 41 WAVE SELECTOR BUTTONS The two WAVE selector buttons are used to switch between the different algorithms and categories in the osc group Hold SHIFT and press the WAVE buttons up or down to choose a category Analog FM Digital The LED indicators show which category is activated Press the WAVE buttons up or down without SHIFT to switch between the different algorithms or waveforms within the selected category Page 35 6 The
118. s Comprehensive effects section A medium weighted hammer action 88 76 note keyboard with Aftertouch or a 73 note semi weighted waterfall keyboard with Aftertouch An Extern section for controlling external MIDI instruments A Morph feature for applying multiple parameter changes to a sound with controllers Splits and layers are easily set up by assigning instruments to Keyboard Zones But that s not all There are two independent Panels A and each containing a full setup of the Stage instruments This means that you have access to six instrument sections and two independent effect sections Amongst other things this allows for dual manual B3 organ emulation and easy setup of all kinds of instrument layering and splits Page 5 1 Introduction About the Owner s Manual Nord Stage EX v6 x ABOUT THE OWNER S MANUAL The manual is arranged mainly as a reference manual In many cases you ll get tips on how to prac tically use the functions alone and also together with other functions Every time the manual wants your attention to an object on the Stage the name of that object will be printed LIKE THIS e g press the STORE button The LCD display on the Nord Stage EX is always referred to as the DISPLAY Whenever there is a reference to the keyboard that reference also applies to any incoming MIDI note messages READING THE MANUAL IN ADOBE ACROBAT READER This manual is also available in th
119. s selected you will trigger organ sounds before the key is fully depressed This mode closely mimics the way a real B3 triggers notes Fast High Default Normal Sustain Pedal Polarity This allows you to change the polarity of a connected sustain pedal in case the functionality of the pedal is reversed i e when the pedal is up sustain is on and vice versa Open Closed Default Sustain Pedal Use as Rotor Rotor Pedal Polarity If you have only one pedal connected and want to use it as both Sustain Pedal and Rotor Speed Pedal enable this setting Note that even if this is enabled and you connect a pedal to the Rotor Speed input this setting will be overridden and you will be able to use both pedals separately This allows you to change the polarity of a sustain pedal connected to control Rotor Speed in case the functionality of the pedal is reversed i e when the pedal is up Rotor Speed is fast and vice versa No Default Yes Open Closed Default Rotor Pedal Mode If you are using a sustain pedal connected to control Rotor Speed this allows you to set how this should operate Hold means that the Rotor Speed is fast for as long as the pedal is down and reverts back to slow when the pedal is released or vice versa depending on the set pedal polarity Toggle means that the fast slow rotor speed is switched with a pedal depres sion like an on off switch pedal Hold Default Toggle
120. s on the Nord Stage panel There is one Synth section for each panel and they share 16 voices which are dynamically allocated between the panels You can play two different sounds simultaneously layered or in splits If you for example layer the Synth sections of both panels you can create really complex and evolving sounds Page 34 Nord Stage EX v6 x 6 The Instruments The Synth section Osc GROUP ANALOG TIMBRE CONTROL FM WAVE 4 5 6 DIGITAL y o 10 VELOCITY TIMBRE ENV CATEGORY OSCILLATOR ARCHITECTURE A lot of effort has been spent on creating a versatile and powerful oscillator section for the Nord Stage Synth Based on a variable architecture it provides three different synthesis techniques Analog FM frequency modulation and Digital wavetables For each category there is a number of predefined algorithms with the main parameters mapped to the TIMBRE knob For example the Analog category provides one or two oscillators with various waveforms with or without hard sync In each case the TIMBRE knob controls one essential parameter such as pulse width relative pitch or sync oscillator frequency This Timbre parameter can then be modulated by velocity or the Modulation Envelope to create dynamic sounds The sonic potential is further enhanced by the fact that the oscillator section actually contains a number of extra oscillators for each voice which are b
121. s possible with sawtooth pulse triangle and cosine waveforms each providing different spectral character FM CATEGORY The basic principle behind FM synthesis is to have one oscillator the modulator modulating the fre quency of another the carrier The carrier can in turn modulate the frequency of yet another oscilla tor etc There are several different algorithms in the FM category ranging from one up to three oscillators operators modulating each other in series with or without feedback on the first operator in the chain Page 39 6 The Instruments The Synth section Nord Stage EX v6 x feedback MX A L MODULATOR feedback X E MODULATOR MODULATOR feedback TN _ M IN CARRIER CARRIER CARRIER ore output output wv The three different FM algorithms in the Nord Stage one two and three oscillator FM with feedback The feedback is not active in all algorithms The Timbre knob controls the FM and feedback amounts When you turn the knob all modulations are increased simultaneously The number of harmonics and their intensity increase proportionally to the FM amount As usual the Timbre parameter can be modulated by Velocity or the Modulation Envelope and it can be Morph controlled by any combination of wheel aftertouch and pedal Each algorithm comes with a number of preconfigured frequency ratios Depending on what kind of sou
122. s two time parameters Attack and Release Decay ATTACK The ATTACK knob is used to adjust how long it should take for the sound to reach from zero to full amplitude after a key has been pressed With long Attack settings the sound will gradually fade in RELEASE DECAY When the attack phase is over the envelope drops back to zero level Use the REL DECAY knob to set the time this should take ENV VEL If you hold SHIFT and turn the ATTACK knob so that the ENV VEL indicator lights up the volume of the notes will be velocity controlled MODE Hold down SHIFT and turn the REL DECAY knob to select Envelope Mode The LEDs below the knob will show the selected mode The Attack Decay and Attack Release modes are illustrated below Level In Attack Decay mode the Amp Envelope rises to maximum amplitude at the set At tack time and then immediately falls back to zero at the set Decay time Time lt gt lt gt Attack Decay time time key release 4 In Attack Release mode the Amp Envelope stays at maximum amplitude until the key is released and then fades to zero gt Time Attack Release time time Page 43 6 The Instruments The Synth section Nord Stage EX v6 x The third Envelope mode indicated by both LEDs is similar to the first mode except that the enve lope quickly goes to zero when the key is release FiLTER SECTION LP FILTER FREQ CONTROL 456 1 din 8 Af
123. se on a folder structure on the hard drive If Search Subfolders 1s active you can browse to the top folder of a structure as the parent of the source files ORGANIZE THE PROGRAM OR SYNTH PARTITIONS By using drag and drop you can organize the content of the Program and Synth partition 1 Make sure that Dual View and Organize is activated in the View menu 2 Select the banks you wish to use as the destination and the source 3 Select and drag a sound from the destination bank to the source bank If you drop a sound on a free location the sound will be moved from the source location If you drop on a location that is occupied the two sounds will trade places SEARCH BOX 1 By entering one or several characters in the Search Box you can filter out the content that is pre sented in the lists This provides you with a quick way to find duplicate programs all programs made by the mysterious AD Ake Danielsson or all programs with e g the phrase string in their names AUTO SELECT By clicking on the Auto Select icon in the toolbar you toggle the Auto Select function on or off When this is activated and you scroll through the Pianos Program or Synth patch list using the com puter keyboard arrow keys these will automatically be selected in the Nord Stage EX Double clicking on a Piano Program or Synth patch will also select it in the Electro 3 Page 78 Nord Stage EX v6 x 13 Nord Sound Manager Nord Sound Manager reference
124. sts the balance between the dry signal and the delay repeats PING PONG If you adjust the Rate Tempo knob the delay may or may not change the pitch of the TEMPO current repeats This is a user selectable option and is set in the Sound menu see page em 68 The FEEDBACK knob controls the number of delay repeats Delay is stereo in out ORG PIANO SYNT SOURCE Page 52 Nord Stage EX v6 x 7 The Effects The Panel effects PING PONG If you press SHIFT and turn the FEEDBACK knob so that the PING PONG indicator lights up the delay repeats will alternate between the left and right channels When short delay times are used the repeats will be asymmetrical and produce delays that are more like early reflections in reverb units TAP TEMPO You can also use Tap Tempo to set a delay time matching the tempo of a song Simply tap the TAP TEMPO button in the tempo you wish the delay to sync to a number of times and the delay time will adjust automatically As long as the Tap Tempo LED is lit the tempo is calculated wait until it goes dark to tap in another tempo Tapping will never result in a pitch change of current repeats While you tap the tempo the calculated tempo and corresponding delay time in milliseconds will be shown briefly on the DISPLAY AMPSIM E Q AMPSIM EQ This effect section combines an three band equalizer with a sophisticated amplifier and speaker cabinet simulation No real amplifier or speake
125. t can be freely assigned to output 1 amp 2 default or 3 amp 4 in stereo or to output 3 or 4 in mono The output routings can be set for each pro gram or globally for all programs which is the default setting In global mode the routing settings stored with the program are overridden by the global settings See System menu on page 66 for more information about the output routings Page 23 6 The Instruments The Organ Section Nord Stage EX v6 x THE ORGAN SECTION ORGAN ORGAN MODEL VIBRATO CHORUS PERCUSSION p VOLUME DECAY HARMONIC g SOFT SLOW 3RD SN SUB3 FUND 3 4 8TH STRI6 FLUTES 5 FLUTE4 KB ZONE SELECT OCTAVE SHIFT PSTICK SUSTPED 1 El 2 3 4 5 6 7 8 SUB SUB3 FUND 2ND 3RD 4TH 5TH eje 1 Je je e ee The Organ section in the Stage features emulations of three classic organ models a Hammond B3 Vox Continental II V Type and a Farfisa Compact DeLuxe F Type PRESET II You select which model to play using the ORGAN MODEL button THE B3 MODEL HAMMOND The B3 Organ in the Nord Stage EX is based on a digital simulation of the mechanical tone wheels of the classic Hammond B3 organ This simulation utilizes innovative and advanced methods to cap ture every nuance of the original B3 sound for example An extremely accurate digital model of the original chorus and vibrato scanner Modeling of the ind
126. ter Windows XP and Windows Vista If you run the Nord Sound Manager on a Windows computer you also need a Clavia USB Driver of version 2 14 or later installed The Nord Stage and Stage EX OS has to be v5 0 or later Nord Stage EX OS Updates USB drivers and instructions on how to install these are available at the www nordkeyboards com website and on the DVD that accompanies this unit OVERVIEW You can work with the contents of the piano partition the program partition and the synth patch par tition These are all accessed from the tabs conveniently labelled Piano Programs and Synth Below the tabs is a drop down menu with which you select one of the banks in the partition f no Nord Stage EX is connected properly to the computer pages and memory locations will be greyed out Page 72 Nord Stage EX v6 x 13 Nord Sound Manager Overview Important The actions that take place in the Nord Sound Manager will affect the memories in the Nord Stage EX The Manager is on line with a connected Stage at all times any changes that you perform in the Manager will immediately be executed in the Nord Stage If you e g delete a piano or a program from the list in the Nord Sound Manager that same piano or program will also be deleted from the Nord Stage EX Flash memory THE TOOLBAR B NE B B Organize Dual View Auto Select Sound Up Sound Down Rename Delete BankUp Bank Down Backup Restore The Toolbar gives you direct a
127. the LIVE 1 OR 2 buttons all changes to panel settings you make will be continuously saved If you switch the power off or select another Program the settings are still stored in the Live memory so when you power up next time or return to the Live memory all settings will be exactly as you left them Having two Live memory locations means that two independent setups can be saved in this way If Live memory is selected and you decide you wish to store the settings permanently as a Program you can do so using the standard methods see below You can also store Programs into the Live 1 or 2 memory locations in which case the Program set tings will replace the current Live memory settings Note that when you store a Program into either of the Live memory locations the stored settings will be transferred to Live memory i e any changes you make will be stored continuously and you will not be able to revert back to the exact settings as they were when stored The Live buffers are useful e g for improvisatory performances and as scratch pads for new sound setups Page 19 5 The Program section Storing Programs Nord Stage EX v6 x STORING PROGRAMS Storing a Program will overwrite the existing Program in the selected memory location Note When Nord Stage EX is shipped from factory Memory Protect is set to On To be able to store Programs you need to change this to Off See Memory Protect on page 68
128. the position where you want to enter change a character you can use the VALUE DIAL to scroll through all available characters a z A Z 0 9 Space and By holding down SHIFT and pressing the INS PAGE button you enter a blank step at the cursor position By holding down SHIFT and pressing the DEL PAGE button you erase the character at the cur sor position Alternatively you can press and hold down the KB ZONES 2 OR 3 button This will bring up the characters in the DISPLAY with the focus on the character the cursor was last on You can now use the VALUE DIAL to select a character at the current cursor position When you release the KB ZONES button the cursor automatically moves to the next position 3 Press STORE again Now you can use the same methods as outlined in Storing a Program above to store your name with the Program Page 21 6 The Instruments Introduction Nord Stage EX v6 x 6 THE INSTRUMENTS INTRODUCTION The Nord Stage EX features 3 different Instruments Organ Piano and Synth Each Instrument is two part multitimbral meaning that there are actually two independent sound engines for each Instrument These engines are internally connected to the Panels one for Panel A and another for Panel B The Organ behaves a little differently in that there is actually only one engine but it supports two man uals with separate drawbar settings see About Split Organ Setups on page 29 C
129. to the computer and launch the Nord Sound Manager 4x 2 The Piano tab will open and the current content of the Piano partition in the Stage will be dis played Piano Program Synth Bank All 16 sounds Bank a Loc Name Size Ver Grand 1 StudioGrand 2 XL YaC7 Clos 4 4 62 1 MB 4 40 Grand 2 ConcertGrand1 XL Stw D Clos 4 4 47 8MB 4 40 Grand 3 Stage Grand YaC7 Close 4 2 21 5 4 20 Upright 1 RainPiano SvPianoFab 4 4 22 3MB 4 40 E Grand 1 Electric Grand 1 CP80 4 3 1 4 30 E Grand 2 Electric Grand 2 CustomBuild 4 3 5 2MB 4 30 E Piano 1 E Piano 1 Mk I Deep 4 4 5 2MB 4 40 E Piano 2 E Piano 2 MK I Suitcase 4 4 5 3MB 4 40 E Piano 3 E Piano 3 MK II ShallowClos 4 4 5 8 8 4 40 E Piano 4 E Piano 4 MK V Ideal Close 4 4 5 4MB 4 40 Wurl 1 Wurlitzer 1 200A 4 4 5 6MB 4 40 Clay 1 Clavinet D6 4 1 5 6MB 4 10 Clav 2 Clavinet D6 4 1 Clav 3 Clavinet D6 4 1 Clav 4 Clavinet 06 4 1 Clav 5 Harpsichord Ital Short Strin 4 2 9 6MB 4 20 Clav 6 Harpsichord Fr Lower8 4 3 15 7 4 30 Clav 7 Harpsichord Fr Up8 Lows 4 3 15 3MB 4 30 Clav 8 Harpsichord Fr Lute 4 3 11 3MB 4 30 3 Select the piano to delete and press the Delete icon in the toolbar You can also right click on the sound and choose the Delete option or use the backspace or delete keys on the computer key board You will be asked to confirm your intentions and then the piano in the Stage EX will be deleted Page 75 13 Nord Sound Manager The Quick Tour Nord
130. trument while simultaneously raising it for the other This allows you to morph seamlessly between two sounds by using the Wheel 1 Set up so that you have two Instrument sections active e g the Piano and Organ section and that these are assigned to the same Zones so that they are layered when you play the keyboard 2 Set the LEVEL knob for one of the two active instrument sections to the maximum value fully clockwise and the LEVEL knob for the other active instrument section to the minimum value fully counter clockwise 3 Hold down the WHEEL button in the Morph Assign section and turn the LEVEL knob set to max imum value down to minimum value As you can see the encoder LED pointing to the maximum value position where it initially was set stays lit and the encoder LED pointing to the minimum value position where you just set it is also lit The two lit encoder LEDs now indicate the Level range see About setting Morph parameter ranges on page 62 controlled by the Morph Assign function which in this case was the full range of the Level rotary encoder 4 Release the WHEEL button in the Morph Assign section and push the Wheel forward The Level knob is now controlled by the Wheel and the LED s continuously reflect the level changes when moving the Wheel In this example when the Wheel is fully forward the Level goes down to zero and when you move the Wheel back the Level goes back up to maximum Page 60 Nord Sta
131. tton in the Morph Assign section and press the ROTOR SPEED button once Now the Wheel controls the Rotor Speed which is indicated by clearly lit ROTOR SPEED LEDs when the corresponding Morph button is held Note that this enables you to set Rotor Speed continuously instead of just alternating between two fixed speeds To deactivate hold down the WHEEL button in the Morph Assign section and press the ROTOR SPEED button again Page 61 9 The Morph Assign feature About setting Morph parameter ranges Nord Stage EX v6 x ABOUT SETTING MORPH PARAMETER RANGES In the previous example we controlled the full range of two Instrument LEVEL knobs with Morph But you can also set relative ranges for parameters For example you could assign one parameter to be controlled fully min max and another parameter knob to be controlled from 12 o clock position to 3 o clock position This would mean that the first parameter would vary between the min and max values whereas the second parameter would vary between 12 o clock position to 3 o clock within the Morph assigned controller s full range When you press and hold down one of the buttons in the Morph Assign section to assign Morphing the initial position of a parameter determines the first value and the position you move the parameter to determines the second value Using the Wheel as an example this means that when you move the Wheel fully forward the parameter will move from the first value to end up
132. types of vi bratos V1 V3 Select one of these types by pressing the SELECTOR button You activate and deac tivate the Vibrato section by pressing the ON button KEY CLICK CONTROL On an original B3 organ the key click produced by the random contact bounces was originally an unintended audio artifact This particular artifact later became a desirable effect amongst musicians In the Nord Stage EX you can select the amount of key click that should be present in the B3 organ sounds 1 Press the SHIFT SOUND buttons to access the Sound menu page 2 You use the PAGE buttons to navigate to the Organ Key Click Level menu item 3 Now you can use the VALUE DIAL to change the Click Level 0 100 Default setting is 50 When you are done press the ExIT SHIFT button Page 26 Nord Stage EX v6 x 6 The Instruments The Organ Section THE V TYPE MODEL Vox CONTINENTAL Il The Vox Continental is probably the most famous of all the transistor based combo organs that emerged in the early 60 s Transistor technology made it possible to manufacture much more compact and portable organ instruments Compared to the mighty sound of tone wheel based organs transistor organs generally sounded reedier and weaker but the Vox Continental had a distinctive sound char acter which together with the portability and cool design inverse keyboard and chrome Z frame stand made the instrument massively popular at the time The sound is timeless and re
133. ument samples The total capacity of the Flash memory is 256 MB in the Stage EX The internal sound memory of Nord Stage consists of 21 Banks holding 6 Programs each for a total of 126 Programs In addition there are the two Live buffer memories which will continuously store any changes as they are made and remember these settings after the power is shut off FACTORY PRESETS All factory Programs of Nord Stage EX can be replaced To make sure you don t accidentally over write Programs you want to keep it s a good idea to back up your sounds regularly on a computer or on a hardware sequencer that can record and play back MIDI SysEx data For information on how to back up Programs please refer to Sending Program dumps on page 88 This functionality as also available with the Nord Sound Manager RESTORING THE FACTORY PRESETS The factory Programs will be available as a MIDI SysEx file for download at the Nord web site at http www nordkeyboards com Please refer to Receive MIDI SysEx Dumps on page 89 for infor mation on how to restore the factory presets using MIDI If you like to reset everything including the pianos use the Restore functionality in the Nord Sound Manager together with a Stage EX backup file that is available on the DVD or as on the www nordkeyboards com web site OS UPGRADES The latest OS version for Nord Stage EX is available for download at http www nordkeyboards com Page 71 13 Nord Sound
134. un til you release the button Each drawbar represents a harmonic sometimes called a partial In C3 the figure you can see the pitch Jn the illustration above we have chosen as our reference note The interval among the nine draw FUND drawbar is considered the basic fundamental harmonic in the bars Note that the SUB3 draw organ sound The arrows point at the respective note that each drawbar bar actually lies a Sth above the represents when C3 is our reference note fundamental harmonic Howev er in most situations it is perceived as sounding below the basic harmonic When you play different notes on the keyboard the harmonics are being transposed up or down with the fixed harmonic inter vals PERCUSSION PERCUSSION In the original B3 the Percussion effect is generated by a single en ME lar velope generator that controls either the 2nd or 3rd harmonic The envelope opens up for a short moment in the beginning of the sound when you press the key s You activate and deactivate the Percussion effect by pressing the ON button The Percussion effect can be set to control either the 2nd HARMONIC 3RD button LED Off or 3rd harmonic Page 25 6 The Instruments The Organ Section Nord Stage EX v6 x The envelope Decay time can be set to Fast DECAY button LED Off or Slow and the Volume characteristics to Normal VOLUME button LED Off or Soft level level
135. und make sure the actual instrument samples are already loaded in the Nord Stage EX Otherwise the parameters in the SysEx message will be applied to another available Piano instrument Page 88 Nord Stage EX v6 x 14 MIDI functions Program Controller and Synth Sound dumps SENDING MIDI CONTROLLER DUMPS 1 Set up as in steps and 2 in the previous description 2 PRESS SHIFT MIDI and select the Send MIDI Ctrl menu item using the PAGE buttons Select to send all Controllers from Panel A or Panel B by using the VALUE DIAL or by pressing the corresponding PANEL button 3 Press the STORE button to send the dump to the MIDI OurT of Nord Stage EX The STORE indi cator will stop flashing once the dump has been sent SENDING SYNTH SOUND BANK DUMPS You can perform a separate MIDI SysEx dump of the Synth memory banks You can select to send a single sound from the currently active Panel one of the category banks Synth Pad Bass or all banks at once 1 Set up as in steps and 2 in the preceding description 2 PRESS SHIFT MIDI and select the Dump Synth Sound menu item using the PAGE but tons Select to send the synth patch from the active Panel one synth category or all synth sounds by using the VALUE DIAL 3 Press the STORE button to send the dump to the MIDI OvT of Nord Stage EX The Store indica tor will stop flashing once the dump has been sent RECEIVE MIDI SYSEx DUMPS To receive a MIDI SysEx Dump
136. ut will control Swell for all organ models If you have only one expression pedal it can be used both as a generic Control Pedal and a Swell Pedal See Control Pedal Use as Swell on page 67 ROTARY SPEAKER The Rotor section rotary speaker simulation is logically placed next to the Organ section but you can also use it for Piano or Synth sounds just like the other effects The Rotor effect is described on page 55 ORGAN PRESET amp Il PRESET Il For each Organ Model and separately for Panel amp B you can store two organ Presets within a sin gle Program This is a quick way of changing between two sound variations without having to change Programs You change between Presets I amp II by pressing the PRESET II button The drawbar settings and the Vibrato Percussion on off settings are stored in a Preset ABOUT SPLIT ORGAN SETUPS If you press SHIFT and the SPLIT ORGAN button you will activate a basic Split Organ setup where Both Panel A and B are active In this mode the keyboard is split to play a Lower and an Upper Manual organ Panel A settings control the Lower Manual and Panel B the Upper Manual By default the split point is set at middle C A blinking PANEL button indicates which Panel is edit active i e which of the two Panel s settings are currently shown To edit show settings for the other Panel Manual press the corresponding PAN EL button Each Panel Manual can have the

User Manual Nord Stage EX

Contents

Download Pdf Manuals

Related Search

Related Contents