manual for use and maintenance - parts-shop
Contents
1. Fig 20 Position of the oil recovery tray The oil tank holds around 9 Lt of oil Remove the oil plug 3 in fig 20 and fill the tank with the correct oil see page 5 for oils to be used pouring in around 6 Lt Switch on the log splitter and activate the telescopic mast for 1 3 of its complete travel Lower the wedge completely and add the remaining oil Run the machine for two complete cycles to bleed any air from the hydraulic circuit Use the oil rod fig 3 page 8 to check the right quantity of oil Ten Clean the inlet of the oil plug and replace the plug Fig 21 Removal of the plug Wy WARNING NEVER MIX OIL WITH GENERAL WASTE USED OIL MUST BE DISPOSED OF ACCORDING TO CURRENT REGULATIONS IN THE COUNTRY WHERE THE MACHINE IS USED 13 SPV26 English 6 3 Sharpening the wedge After long periods of operation and when required sharpen the wedge of the log splitter using a fine toothed file and taking care to remove any burrs or crushed parts of the metal NOTE For routine maintenance of the petrol or diesel engine for model SPV26 BS refer to the related attached booklet 7 TROUBLESHOOTING Problems that may arise when using the log splitter and recommended remedies are given in the table below In the case of operations carried out by unauthorised personnel the guarantee will be immediately null and void and the manufacturer will be relieved of any responsibility for injury to persons and2. 15 SPV26 English APPENDIX A WIRING AND HYDRAULIC DIAGRAMS w WARNING The following is reserved solely for the authorised personnel of the retailer The manufacturer declines any responsibility for damage or injury of any kind ensuing to persons animals or objects due to improper or unauthorised use of this documentation HYDRAULIC DIAGRAM 1 Cylinder nni 2 Control valve Sur 4 3 Max pressure valve 1 wi 4 Motor L 5 Pump 2cm round 45 6 Tank SINGLE PHASE ELECTRIC DIAGRAM THREE PHASE ELECTRIC DIAGRAM L1 L1 L2 N L3 PE N PE re 01 EN eo gn ge 2 Gi Wi vi UT ny Il d Hi NI English SPV26 APPENDIX B SPARE PARTS Replacement of spare parts and therefore extraordinary maintenance of the machine must be carried out by the retailers specialised and authorised personnel only If any maintenance operations other than those expressly indicated in this handbook are carried out the warranty will be immediately null and void and manufacturer shall be relieved of all and any responsibility with regard to accidents involving persons animals or things Always order spare parts form your regular retailer
3. Never try to release a jammed log while the machine is running The machine must be switched off during this operation Never request the assistance of another person to help you remove a jammed log ii English SPV26 3 1 A For machines with electric motor do not use machines with electric motor if natural gas petrol fumes or other inflammable vapours are present check that the electric circuit is adequately protected and that it corresponds with the power voltage and frequency of the motor check that there is a ground connection and a regulation differential switch upstream Use cables with a section of 2 5 mm Avoid use of free and inadequately insulated connections Connections must be made with protected material suitable for outdoor use Make sure that the machine and the cable never come in contact with water to prevent accidental start up ensure that the switch is off before plugging in the power cable treat the power cable with care do not attempt to move the machine by pulling the cable do not yank the cable to unplug it keep the cable away from excessive heat oil and sharp objects never leave the machine unattended with the power supply on also disconnect the power cable when not in use when carrying out maintenance work when changing attachment or moving the machine 3 1 B For machines with fuel engine take the necessary precautions against fire when working i
4. D05410190 E27150090 E26760012 E26310151 D05410310 E26451200 E26075104 E26561344 E26760014 D05410300 B41080060 E26840014 B07000020 B73200020 B82760020 E26401106 B71100100 B71010350 E28560020 B71010260 B71010270 E26770160 B71010240 D05000550 E51436044 B71010230 D05000540 E28560200 E26150096 E26513038 D05000560 E26075107 B73200010 E26075106 B41000300 E26114068 E26075102 Oo JO O1 E ND 22 http www bell ug I UT Ki a 5 via De Pisis 5 42100 Reggio Emilia Italy Tel 39 0522 505911 Fax 39 0522 514204 Email bell bell it a Certified Company according to Quality System ERP DIN EN ISO 9001 2000 Zertifikat 15 100 31581 Dichiarazione di conformit Conformity declaration Konformit tserkl rung D claration de conformit Verklaring van overeenstemming F rs kran om verenstimmelse Overensstemmelseserkl ring Erkl ring Vaatimustenmukaisuusilmoitus Declaraci n de conformidad Declara o de conformidade via E de Pisis 5 Reggio Emilia Italy dichiara che la macchina declares that the machine best tigt hiermit dass die von Ihr hergestellte Maschine d clare que la machine verklaart dat de machine intygar harmed att maskin erkl rer herved at maskinen bekr fter hermed som firma at have fremstillet denne maskine t ten vakuutamme ett laitemme declara que la maquina declara que a maquina SPV26 conforme ai Requisiti
5. English MOTOR AND PUMP GROUP mod T Code E51261014 E51334010 D55080400 E51430052 E51351114 D05180100 E51091030 B55630200 E51430048 E51461060 D20010020 E26075087 E51041134 E51327120 D55080220 JO Om ND Code E34020110 E26780050 E26510067 E34030110 E34010110 E34070010 E85080100 E85080050 E26075105 E26760014 E26561344 E26075107 E34050100 E53010065 D55080360 SPV26 20 SPV26 Code E26760015 E26840019 E26035114 B66211520 E26075105 E53020110 E51430065 E51313136 D55080240 E31085126 E26560515 E26075125 B71010090 B71010080 B77000190 E34100010 E26515069 E26150121 E26513370 JO Ob ND English PUMP GROUP mod GC Code E26840057 E31150120 E51141032 E51430052 B28690030 E51131144 B55630060 D05180100 E51091030 D05130140 E26075107 B55630200 E51041134 E51327120 D55080220 E26760014 E26561344 E51461060 English PUMP GROUP mod GI Code Code E26760015 E26840019 E26035114 B66211520 E26075125 E26560515 E26075105 E53020110 E51430065 E51313136 D55080080 E31085726 E26840057 E31150120 E26513370 B71060020 B28690030 JO O1 ND E26035114 E51131144 B71010090 B71010080 E51430052 E51313136 D55080220 E51327120 E51041134 B55630200 E51091030 E26075107 D05130140 D05180100 E26760014 E26561344 E51461060 SPV26 21 SPV26 English ZHB CONTROL Code
6. fig 18 and take off the hose from the lead of the filter support Unscrew the three screws 2 by using an allen wrench then extract the filter group giving care to the gasket 2 in fig 19 Remove the filter 4 from its support 1 using an exagonal wrench holding on the point 3 Wash the filter with petrol and if possible blow it with compressed air Screw again the filter 4 on the support 1 Inserting the filter group in its seat placed in the oil tank paying attention to the correct position of the gasket 2 Lock the filter group with the three previously taken off screws Joint the hose then lock it by the clamp 6 2 How to change the hydraulic oil The spent oil must be replaced with new oil of the type indicated on page 5 every 600 hours of operation To change the oil proceed as follows Make sure that the mast of the machine is fully retracted wedge closed Raise the log splitter slightly and rest it on two chocks 2 in fig 20 Place a receptacle fig 20 able to hold around 10 Lt of oil under the oil drainage plug located to the rear of the machine Unscrew the drainage plug pos 1 figures 20 and 21 with a suitable wrench and let all the oil in the tank drain into the receptacle Once the tank is empty clean the inlet the copper washer and the drainage plug with petrol and then replace the drainage plug drawing this up tightly Remember to insert the washer fig 21
7. in fig 1 Carrying handle Fig 1 Machine parts Splitting length Wedge adjustment ZHB control levers Telescopic mast Current socket Work surface Main switch Control valve Oil tank Oil plug Motor electric motor in the figure Wheels for minor movements PERMITTED AND MANDATORY NOTE Only the SPV26 log splitter with electric motor is shown in fig 1 The WORK AREA configuration of the other models with different drive system varies d il d A 1 1 Symbols used SPV26 English Standard graphic symbols are used on all machines in order to ensure complete safety of all parts of the log splitter As these symbols are very important read the information below attentively it is obligatory to read the machine s use and maintenance manual in full before using the machine in normal conditions of use our machines may expose the operator daily to noise levels lower than or equal to 85 dB a it is therefore obligatory to wear ear defenders ec it is obligatory to wear safety footwear at all times to provide protection against the risk of logs accidentally falling on feet P it is obligatory at all times to wear gloves which protect the hands against chips and splinters which may be produced during work it is obligatory at all times to wear a helmet which protects the hands against chips and splinters which may be produced during work it is obligatory at all times to
8. log splitter with petrol or diesel engine SPV26 BS 5 1 C Switching on off of the tractor driven log splitter SPV26 IT SPV26 GC SPV26 Gl aana eaaa eaaa eaaa aane 10 5 2 ele Oe TN ler EE 14 5 3 Movable work surface 5 4 How 10 adjustblade Stroke Hits ne AR gak A A AK gates ae a gee teens a anaes gan aaa e 11 5 5 Howito transpon EE ll pre en ei SR KENA ga ir lava hes eaaa a ae pal ee eas eee 12 5 6 Assembly and use Ee EE 12 ell NEE Le 6 1 How to clean the oil filter 6 2 Howt0 change the hydrauli EE 13 6 3 Sharpening the wedge EE 14 TROUBLESHOOTING E 14 7 1 Resetting of the thermal cut out of the electric motor ss 14 DISMANTLING OF THE LOG SPLITT R 222 aa ARR aga ne A el tend nes iii GUARANTEE aaa adas Nak aa aa e agan Ta gak aapa ba aa bah a aa ete Aah da Lala a aa Daha SG iii APPENDIX A WIRING AND HYDRAULIC DIAGRAMS APPENDIX B SPARE PARTS EE w WARNING When the machine is delivered check for any missing parts and for any damage during transport Any complaints must be forwarded immediately to the carrier and to the retailer Any subsequent complaints will not be accepted ii English SPV26 INTRODUCTION BELL log splitters have been designed and manufactured in compliance with the most recent European safety regulations with particular reference to the EN609 and UNI60204 standards The ZHB control systems have been designed and engineered so that the operator is forced to
9. Essenziali di Sicurezza e di Tutela della Salute secondo la Direttiva 98 37 CEE ela Norma Armonizzata EN 609 1 03 99 is in compliance with the essential Security and Health Protection requirements according to the 98 37 EEC Directive and to the harmonised Norm EN 609 1 03 99 den wesentlichen Sicherheits und Gesundheitsschutz Erfordernissen entspricht gem ss der Bestimmung 98 37 EG und der harmonisierten Norm EN 609 1 03 99 est conforme au qualit s de S curit et Protection de la Sant demand es selon la Directive 98 37 CEE ainsi que selon la Norme harmonis e EN 609 1 03 99 overeenstemt met de fundamentele veiligheids en gezondheidseisen zoals die zijn vastgelegd in Richtlijn 98 37 EEG en de geharmoniseerde norm EN 609 1 03 99 ar i verensst mmelse med s kerhets och h lsokraven enligt EU direktivet 98 37 och standarden EN 609 1 03 99 er i overensstemmelse med sikkerhetskravene og helsevernets forskrifter ifolge EU direktivet 98 37 og standarden EN 609 1 03 99 svarer til de grundl ggende sikkerheds og sundhedskrav 1 henhold til EU direktivet 98 37 EF og standarden EN 609 1 03 99 on direktiivin 98 37 EY ja standardin EN 609 1 03 99 olennaisten turvallisuus ja terveysm r ysten mukainen responde a los Requisitos Esenciales de Seguridad y de Tutela de la Salud en conformidad con la Directiva 98 37 CEE y la norma armonizada EN 609 1 03 99 em conformidade com os Requisitos Essenciais de Segura
10. Fig 7 Connection of the cardan shaft 4 2 Lighting Lighting must be provided in the entire work area of the log splitter to ensure perfect visibility when operating the machine and during maintenance and adjustments Even when working outdoors there must be sufficient light to work safely Working at times when insufficient light may result in poor visibility of the machine and its components dawn dusk night is forbidden SPV26 English WARNING When working and after switching off the log splitter never touch any part of the engine as this could cause burns After switching off the machine wait until the engine has cooled before performing any operation Refer to the attached manual for any other information regarding the BRIGGS amp STRATTON engine 5 1 A Switching on off of the log splitter with electric motor SPV26 E SPV26 T Make sure that the switch cutout of the general power system and the switch of the machine are OFF Connect the electric log splitter to the power system inserting the plug in the socket on the electric motor Never pass the power cable over the telescopic mast close to the wedge or anywhere where it may be damaged or cut Set the main on off switch and then press the switch in the green area to start the log splitter The telescopic mast will move automatically to the fully open position Use the log splitter as explained in paragraph 5 2 on page 11 Never leave the log splitter unattended wi
11. V26 GC SPV26 Gl Connect the log splitter to the power source see chapter 4 OPERATING THE MACHINE FOR THE FIRST TIME pages 8 or 9 and then check that the machine is firmly positioned on the ground Start the tractor making sure it does not move Start the log splitter by activating the power system power take off cardan shaft etc The wedge will lift Use the log splitter as explained in paragraph 5 2 on page 11 If you leave the log splitter unattended switch off the transmission system of the tractor After using the log splitter switch off the transmission system switch off the tractor Before moving the tractor lift the log splitter to a sufficient height so that it does not hit the ground WARNING Never move the tractor with the power source of the log splitter activated or with the log splitter still on the ground 10 SPV26 English 5 2 How to use log splitter Place the log on the work surface as shown in fig 10 making sure it is centered under the wedge The two faces of the log must be parallel to each other and to the work surface to guarantee safe operation Working in the mandatory position only fig 1 page 3 grasp the log with the levers of the ZHB control so that the jaws penetrate slightly into the bark and then lower the levers fig 11 a the wedge will start to cut into the log Note As soon as the wedge starts to split the log widen the arms of the ZHB control slightly fig 11 b cont
12. animals and damage Log fails to split Hydraulicpressure too low Contact your dealer Oil leack Locate the leack using a piece of card or wood Contact your dealer Wedge do not cut Sharped the wedge check for burrs or nicks file if necessary Incorrect positioning of the log Change the position of the log in relation to the wedge Log exceeds permitted dimensions Try to cut a small part or use other means to reduce the size of the log Air in the circuit Check oil level Top up if necessary If problem remain contact your dealer Rod advances jerkily or with strong Unions not properly tight Tighten unions vibrations Oil leak from the unions pump or Seals worn Contact your dealer cylinder 7 1 Resetting of the thermal cut out of the electric motor In the case of machines with electric motor a protection device applied to the motor and integrated in the main on off switch is tripped in the case of overloads sudden increases in voltage or accidental faults in the electrical system In this case before calling your authorised service centre wait a few minutes and then try to reset the main on off switch If the problem does not re occur the log splitter can be used normally If the cut out is tripped again do not try to reset it and contact your ahthorised service centre DISMANTLING OF THE LOG SPLITTER The log splitter must be dismantled complying with all safety regulations designed to prevent injury and damage All parts
13. d NU um IUT MANUAL FOR USE AND MAINTENANCE SPV26 i CE 1996 BELL FORM D22000076 ver 2 PEER SPV26 TABLE OF CONTENTS gt N INTRODUGTIONI eil iaia 3 DESCRIPTION OF THEIMACHINE i c i ideale aaa 3 14 Symbols Used asana aaa are ara cea ita 4 TECHNICAL DATA iaia adele 5 SAFETY ei RL ale lia 6 34 General Safety regulations odia ee Ten e ads hehe ta donned ia aa ates Mate eles vida ie ata 6 SMA FOr MACHINES With el ctric Motor aaa ai 7 3 1 B For machines with fuel engine 3 1 C For machines with connection to the hydraulic system of the tractor IT 7 3 1 D For machines with pump on the tractor power take off GI see 7 SALE Formachines driveniby cardan shaft GE sasasi atasane a aa dE aa kaa ANG AN Reit 7 OPERATING THE MACHINE FOR THE FIRST TIME iaia ganda tent d 6 gan dn gaga gen aa NG pa ANNA ETAS 8 4 1 A For machines with electric motor 41B Forimacnin s with fuel engine csi eeben it dette EA NK a pana Kaka pa in gaga a NA Da alaa a GU e fc aa ma a eae 4 1 C For machines with connection to the hydraulic system of the tractor IT 8 4 1 D For machines with pump on the tractor power take off Gl 9 4 1 E For machines with pump on the tractor power take off GC sise 9 4 2 IO 9 USE sigilli lilla 10 5 1 A Switching on off of the log splitter with electric motor SPV26 E SPV26 T ii 10 5 1 B Switching on off of the
14. ed ap 540 rpm rp m HU UT jen English SPV26 2 TECHNICAL DATA TECHNICAL DATA SPV26 BE Max working pressure bar Max force tons sio 230V 50Hz 230V 50Hz 3 ph Premium i uppy Single ph 400V 50Hz 3 ph grade fuel Latina 230V 3 ph 16 1A Noise lt 85 dB A measured at the height of the operator s ear in the working position with the log splitter in operation The ears must be suitably protected ear defenders ifthe log splitter is connected to a tractor machine noise is amply covered by that of the tractor 10 30 cm Recommended oils We recommend use of the following oils for the hydraulic cylinder SHELL TELLUS T22 ARAL VITAM GF22 SP ENERGOL HCP22 MOBIL DTE11 or equivalent DO NOT USE OTHER GRADE OILS For the type of oil to be used with the SPV26 BS model with petrol or diesel engine refer to the engine manufacturer s i recommendations given in the Fig 2 Maximum size of the log to be split related booklet SPV26 English 3 SAFETY The information given in the chapter is extremely important for safety purposes It describes possible hazards tied to use of the machine and instructions for correct use of this to avoid injury or damage WARNING The BELL Mod SPV26 log splitter has been designed and manufactured to split logs of the sizes recommended on page 5 only Use of the machine for any other purpose shall be considered improper and t
15. ents covered by their own guarantee such as internal combustion engines diesel engines etc This guarantee covers only defects arising during proper use of the machine BELL shall accept no responsibility whatsoever if BELL components break while under guarantee for reasons such as 1 Misuse negligence improper handling abuse or accident 2 Failure to carry out reasonable or necessary maintenance as prescribed in this manual renewal of worn components such as slides hydraulic oil engine oil gearbox oil blade not sharpened etc 3 The use of parts or accessories not manufactured supplied or approved by BELL BELL does not provide further explicit or implied guarantees other than those set forth herein No representative or dealer is authorized to assume other responsibilities with regard to BELL products The duration of the implicit guarantees recognized by the law including the commercial guarantees and conventions for particular purposes are limited in duration to the validity and duration of the explicit guarantee granted below BELL shall upon no account act as guarantor for loss of profit whether direct or indirect specific or deriving from any damage To validate this guarantee the seller must complete and return within ten 10 days of the date of sale or the date of hire the guarantee registration card supplied with each unit sold If you require spare parts or repair work it will be useful the followins informations
16. he manufacturer shall not be liable for any injuries or damage to be ascribed to improper use of the machine The operator must work in the position shown in fig 1 only and operate the machine drive control with both hands without using other makeshift systems and without tampering with the ZHB control When the machine is working persons and animals must be kept at a distance of at least 5 meters from the machine NEVER ATTEMPT TO TAMPER WITH THE PROTECTIONS OF THE LOG SPLITTER OR TO OPERATE THE MACHINE WITHOUT THESE FAILURE TO COMPLY WITH THE INSTRUCTIONS GIVEN IN THIS CHAPTER MAY RESULT IN SERIOUS INJURY OR DAMAGE TO PERSONS THINGS AND TO THE MACHINE 3 1 General safety regulations The machine must always be used by one operator only Nobody must be allowed to use the log splitter unless they have read the instruction manual and have been instructed in the regulations to follow for correct and safe use The machine must be used by adults only Use of the log splitter by apprentices of not less than 16 years of age must be supervised by an adult authorised to use the machine Never wear loose unbuttoned clothing which may become trapped in moving parts Do not move the log splitter while the motor is running Do not work on sloping or slippery ground position the machine in a flat area free from objects which may impede the freedom of movement of the operator Check that the logs to be split are free from nails
17. inuing to press the levers down so that the force applied does not damage the jaws If the log does not split quickly or if the wedge stops do not keep the machine under force Then hydraulic oil overheats very quickly with damage to the pump It is advisable to return the mast to the idle position and to make another attempt after rotating the log Repeat the operation with the pieces obtained so as to split the log into several parts Note If you let go of even just one of the levers the machine will stop in the position reached If you let go of both levers the telescopic mast will move to the fully open position Fig 11 b Two hand control Fig 11 a Two hand control 5 3 Movable work surface The movable work surface 1 in fig 12 allows the log capacity adjustment in relation to the log lenght The plane placed in A position allows to split logs until 72 cm lenght With the plane placed in B position the logs lenght increases until 105 cm but only until the wedge stroke Fig 12 Movable work surface 5 4 How to adjust blade stroke To save time a system has been designed that makes it possible to adjust wedge travel so that this can be set for short logs In this way the wedge travels for the distance required only After checking the length of the longest logs to be split regulate wedge travel as follows _ Start the log splitter and bring the wedge to the position required Release one of machine co
18. n a e de Tutela da Sa de de acordo com a Directriz 98 37 CEE e a Norma Harmonizada EN 609 1 03 99 Il presidente The president Der Pr sident Le pr sident De directeur Verkst llande Direkt r Presidenten Pr sident P johtaja Reggio Emilia El Presidente O Presidente 20 11 02 Oy sus Doren Olmes Ognibene
19. n dry areas do not smoke while working or refuelling never refuel the log splitter while it is running switch the engine off and leave it to cool fill with fuel taking care that the tank does not overflow wipe off any traces of petrol before starting up Handle fuel with care Never touch the engine or the exhaust pipe as they become very hot and may cause burns Wy WARNING DO NOT START THE ENGINE IN AN ENCLOSED SPACE EXHAUST FUMES ARE LETHAL 3 1 C For machines with connection to the hydraulic system of the tractor IT Never connect the log splitter with the tractor moving Use only fast disconnect hydraulic fittings of the correct size and always check that they are correctly fastened and tight 3 1 D For machines with pump on the tractor power take off Gl Never connect the log splitter with the tractor moving Always check that the gearbox is correctly inserted in the tractor PTO Fasten the gearbox to the tractor with suitable chains A short chain may break with consequent injury to persons and damage to the machinery Never touch the power take off when the engine of the tractor is running This can be very dangerous Interrupt work immediately and stop the tractor in the case of any leaks of oil from the pipes or gearbox The tubes are under pressure and any cracks or breaks may be extremely dangerous 3 1 E For machines driven by cardan shaft GC Never connect the log splitter with the
20. n the correct direction as indicated by the arrow w Never open the box containing the switch or open the terminal block on the motor if it is necessary to do so have these operations carried out by your electrician If the fuses blow or the protection valve trips this means that you are overloading the motor or the electrical installation is not correctly rated Consult your electrician Fig 4 Inversion of the poles in the three phase motor 4 1 B For machines with petrol or diesel engine Before operating the log splitter carefully read the user s manual for the engine fitted study the maintenance regulations and guarantee supplied Check the oil level in the engine block top up if necessary WARNING working without oil causes irreparable damage When the engine is new it is important at first start up to let it turn over without performing any work for at least twenty minutes this running in period ensures maximum performance and smooth operation of the whole system 4 1 C For machines with connection to the hydraulic system of the tractor IT Make sure the tractor is off that the parking brake is on and if necessary that the wheels are chocked Before starting work always check that none of the hydraulic tubes is damaged Connect the oil delivery tube marked with a special flat white clip of the log splitter and the discharge tube no marking to the hydraulic system of the tractor Make ce
21. ntrol levers so that the wedge stops in the selected position Back off knob 1 in fig 13 with the other hand Pull the rod 2 up until it locks in place Draw up the knob 1 again making sure it is tight The log splitter will now reposition at the point selected EO Fig 10 Positioning of the log on the log splitter Fig 13 Blade travel adjustment 11 English 555 SPV26 5 5 How to transport the log splitter The Mod SPV26 log splitter must be transported with the wedge mast fully retracted in the body Use the carrying handle on the top part of the mast fig 15 for safe trouble free transport of the log splitter Rest one foot on the base of the log splitter Pull the handle tilting the machine towards you to facilitate transport fig 14 To rest the machine on the ground put one foot on the base and lower the machine carefully Fig 14 How to lift the log splitter Fig 15 How to transport the log splitter 5 6 Assembly and use of the 4 way wedge optional K91000000 The SPV26 model vertical log splitter can be equipped on request with a 4 way wedge to split a trunk into four logs with a single stroke The 4 way wedge A in fig 16 must be assembled directly on the standard 2 way wedge B Position the 4 way wedge so that it is in contact with pin C and fasten it in place by tightening the butterfly screw D which must engage in hole E in the 2 way wedge fig 17 Thi
22. of the log splitter must be scrapped and disposed of according to current legislation where the machine is dismantled Pay particular attention when eliminating hydraulic oil which must not be disposed of in the environment in that it is highly pollutant and must be disposed of according to legal prescriptions 14 ii English SPV26 GUARANTEE The company BELL referred to hereinafter as BELL guarantees to the purchaser of every new BELL original product purchased from a BELL authorized dealer that the product shall remain free from any defects in materials or workmanship for a period of 360 days 12 months from the original date of purchase or the date of first hire Spare parts installed on the product covered by this guarantee are guaranteed for 90 days 3 months from the date of their repair or renewal Such parts must be supplied free of charge to the user by a BELL dealer or distributor during normal working hours BELL reserves the right to inspect any product or part which has been substituted as defective Substituted parts must therefore be kept available for 12 months It is expressly understood that BELL shall be under no obligation to provide labour or accept transport expenses BELL shall accept no responsibility for any damage defect or costs deriving from repairs and or modifications of a BELL product effected by any person other than an authorized BELL representative This guarantee does not apply to commercial compon
23. or wire which may fly up or damage the machine the ends of the logs must be cut square branches must be cut off flush with the trunk Never try to split logs larger than those indicated in fig 2 This could be dangerous and may damage the machine Break wood in the direction of the grain do not place wood across the log splitter and leave it in that position for splitting it may be dangerous and may seriously damage the machine Never attempt to cut two logs at once one may fly up and hit you If the log moves away from the blade retract the ram or the blade and turn the log through 90 Do not attempt to load the log in the log splitter while the ram is in motion you could get trapped and injured Keep your hands well away from any splits and cracks which open in the log these may close suddenly and crush or amputate your fingers _ Do not force the log splitter for more than 30 seconds by keeping the cylinder under pressure at the end of its stroke or by persisting when a log does not split or gets stuck on the blade Oil under pressure overheats very rapidly damaging the pump Never leave the machine unattended while it is running If you leave the machine even for a short time remove the power supply or any possible cause of accidental start up The log splitter must never be used by an operator who is under the influence of alcohol drugs medicines or who is tired A clear mind is essential for safety
24. remembering to indicate the machine model the purchase date and the serial number as well as the code of the parts and the number required Code 2 Code Code Code Code J00902050 09 B02170230 B82110080 E26760013 B50010050 B60460050 E26515072 E26840013 B71200070 B82110020 E26560550 E31650030 E26075082 E26075088 E26515074 B50010010 E26075104 B41080060 E26840026 E28400010 E26760014 D05410300 D05150120 D05170120 E26561344 E28560020 B02170600 E26221042 E55760050 D05260080 E26221039 E26762012 E26071080 B58000030 E26780030 D05110370 D05030040 E26076235 B84520070 E25831336 D05410310 D05110340 D27070020 E57750030 D05410190 E59330010 D30410010 E26015165 B07000020 B71010070 B51450100 E26760020 E27150150 E26035114 E27150200 B37000030 E26760015 E26515069 HI LT KT WI 18 SPV26 English MOTOR AND PUMP GROUP mod GC T Code E26760015 E26840019 E26035114 B66211520 E26075105 E53020110 E51430065 E51313136 D55080240 E31085126 E26560515 E26075125 B71010090 B71010080 B77000190 E34100010 E26515069 E26150121 E26513370 E26840057 E31150120 E51141032 E51430052 D05180100 B28690070 E55011118 B55630040 D05130140 E26570514 E26760014 E26075107 E51091030 B55630200 E51430048 D90010020 E51461060 E26075087 E51041134 E51327120 E53010065 D55080220 E51353134 E51261014 D55080400 E34020110 E26780050 E26510067 E34030110 E34010110 E34070010 E85080100 E85080050 E34050100 D55080360 DONG AKEN
25. rtain that all unions are tight and that there is no leakage of oil Apply a pressure not exceeding 220 bar to the hydraulic circuit of the log splitter Perform a few cycles without wood before starting work so as to vent any air present in the hydraulic circuit When disconnecting the machine from the hydraulic system of the tractor take care not to spill any oil and to replace the plugs on the two tube unions _ 0 English SPV26 4 1 D For machines with pump on the tractor power take off GI Make sure the tractor is off that the parking brake is on and if necessary that the wheels are chocked Insert the gearbox fig 5 directly in the tractor power take off Fasten the two flanges of the gearbox to the two points of the tractor using appropriately sized chains fig 6 making sure they are firmly fastened During use of the log splitter a very high turning force is applied at this point more than 200 Kg Incorrect fastening could cause serious injury and damage _ Before starting work check the hydraulic tubes for any damage and make sure there is oil in the box of the gearbox Working without oil may cause irreparable damage Make certain that the power take off runs in the direction indicated on the gearbox Fig 5 Inlet for power take off Position the accelerator at a suitable rpm for your tractor so that the engine provides sufficient power for correct functioning of the log spli
26. s wedge is used in the same way as the 2 way wedge taking care however not to split very hard wood or wood with a large number of OK NO knots as the use of 2 wedges instead of 1 causes greater stress on the wedge Fig 16 Assembly of the 4 way wedge Fig 17 Engagement of the lock screw 12 ii English SPV26 6 ROUTINE MAINTENANCE This chapter describes routine maintenance i e operations carried out by the operator on the SPV26 log splitter to keep this in perfect working order and therefore reliable for continuous long term use All routine maintenance operations must be carried out with the machine off and in the case of log splitters with electric motor with the power cable disconnected Any other maintenance operation not specifically envisaged in this manual must be carried out by authorised personnel only in that hazardous situations may arise for which the operator is not prepared In the case in which extraordinary maintenance or part replacement operations are not carried out by authorised personnel the guarantee shall be immediately null and void and the manufacturer shall be relieved of any responsibility for injury to persons or animals or damage 6 1 How to clean the oil filter To keep the machine in perfect working order the oil filter of the hydraulic system must be thoroughly cleaned every 300 hours of operation Loosen the hose clamp 1 in
27. thout first of all pressing the switch in the red area off On completing the work switch off the log splitter by turning the switch differential of the general power system to the 0 position off and then remove the plug from the socket on the machine Never yank the plug using the cable Grasp the body of the plug and pull it firmly 5 1 B Switching on off of the log splitter with petrol or diesel engine SPV26 BS Switching on Turn the throttle control knob upper to CHOKE if the engine is cold or to RUN if the engine is still warm fig 8 Turn the accelerator knob lower to IDLE fig 8 a Grasp the engine start up knob and holding it tightly pull it firmly Repeat this operation until the engine starts fig 9 During this phase be very careful not to slip or cause injuries or distortions Once the engine is running the telescopic mast moves to the fully OFF open position Position the accelerator to FAST fig 8 O lt lt g s After a few minutes from cold starting move the throttle control from CHOKE to RUN Fig 8 Accelerator positions fig 8 Use the log splitter as explained in par 5 2 on page 11 If you leave the machine unattended or have finished the work turn the accelerator knob to OFF to switch off the log splitter fig 8 Fig 9 Petrol or diesel engine start up 5 1 C Switching on off of the tractor driven log splitter SPV26 IT SP
28. tractor moving Make sure that the machine is properly fixed to the 3 points of the tractor Make sure that the cardan shaft is fully inserted in the power take off and has clicked in place Never touch the cardan shaft with the engine running SPV26 English 4 OPERATING THE MACHINE FOR THE FIRST TIME Never use the log splitter if it is not in perfect order or if it needs servicing Before starting work check correct functioning of all the safety devices ZHB switch off button on electric machines Before starting work check the level of the hydraulic oil in the tank and top up if necessary with one of the oils indicated on page 5 The level of the oil must be between the two notches on the rod of the oil plug Fig 3 Oil level Before starting work switch on the log splitter and let the oil warm up for a few minutes s After 200 hours of use clean the oil filter as explained on page 13 paragraph 6 1 before starting the machine 4 1 A For machines with electric motor If the motor does not run in the correct direction invert two of the phases in the socket Remove the plug from the log splitter Insert a slotted screwdriver with a suitably sized wedge in the slot located in the connection inlet close to the electric motor as shown in figure 4 Exerting a slight pressure turn the white wheel by 180 This operation physically inverts the poles on the three phase motor Check that the motor runs i
29. tter and check that the power take off does not exceed 540 rpm as shown on the data plate see page 4 par 1 1 SYMBOLS USED WARNING Follow the few very important rules indicated above to avoid problems that could cause injury or damage 4 1 E For machines driven by cardan shaft GC Make sure the tractor is off that the parking brake is on and if necessary that the wheels are chocked Connect the log splitter to the three points of the tractor Connect the cardan shaft to the gearbox fig 7 to the power take off of the tractor The cardan shaft must be of suitable length and complete with protective cover Check that it clicks into place After connecting the log splitter start the tractor and check that the cardan shaft turns in the direction indicated on the data plate on the gearbox Top Connection of the power take off see par 1 1 SYMBOLS USED on page 4 TREY Ola on Position the accelerator at a suitable rpm for your tractor so that the engine provides sufficient power for correct functioning of the log splitter and check that the power take off does not exceed 540 rpm as shown on the data plate see page 4 par 1 1 SYMBOLS USED WARNING Follow the few very important rules indicated above to avoid problems that could cause injury or damage amp WARNING Never touch the cardan shaft or any other rotating parts This is extremely dangerous and may cause injury or damage
30. wear goggles or a visor which protects the hands against chips and splinters which may be produced during work it is forbidden to remove or tamper with the protection devices and safety devices it is forbidden to carry out any maintenance work or to renew parts on the machine when it is running it is forbidden to smoke near the machine and in the work area it is forbidden to stand in the range of action of the machine apart from the operator no other person or animal may be present within a radius of 5 metres from the machine GET ke Dumping of used oil in the environment is forbidden The oil must be disposed of according to current legislation in the country where this operation is carried out Warning direction of rotation of the wedge Never touch the wedge or the supporting arm when in movement Danger of cutting or crushing of the hand never touch hazardous areas while the wedge is moving Warning never remove a log trapped in the wedge with your hands Warning voltage as indicated on the rating plate Danger of burns very hot surface Do not touch Direction of rotation of the motor If the motor runs in the wrong direction follow he the instructions given in paragraph 4 1 on page 8 make certain that the gearbox shaft rotates in an anti clockwise direction and does not exceed 540 rpm make certain that the gearbox shaft rotates in a clockwise direction and does not exce
31. work in the safety area without any possibility of inserting hands or arms in dangerous areas Before transporting installing or operating the machine read all parts of this manual paying particular attention to the specific safety regulations Operators who are unable to understand any of the languages in which this manual is written are responsible for asking the retailer to provide a manual in their own language The operator must also train any other person authorised to use the machine Failure to comply in any way with these instructions improper use of the machine extraordinary maintenance operations not carried out by skilled authorised personnel removal of data plates or markings of any type removal or tampering with the guards and safety mechanisms of the machine or any other action not expressly authorised that may impair the active and passive safety systems of the machine shall relieve the manufacturer of all and any liability and may result in serious injury and damage If the machine is tampered with in any way by unauthorised personnel the guarantee is automatically null and void This manual is an integral part of the machine and must accompany it even in the case of transfer of ownership DESCRIPTION OF THE MACHINE The SPV26 vertical transportable log splitter is equipped with its own electric motor or petrol or diesel engine or with an external connection for powering by a tractor The various parts of the machine are shown
Download Pdf Manuals
Related Search