60W Tri Par 64 User Manual
Contents
1. common DMX 512 out DMX 512 in 3 pin XLR 3 pin XLR REES a ects nd ti XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground 2 cold Pin 1 Ground O Pin 2 Negative 3Hot 3 Hot Pin 3 Postive FIGURE 3 FIGURE 2 Special Note Line termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behaviour Termination reduces signal transmission problems O and interferance it is always advisable to connect a 9 DMX terminal resistance 120 Ohm 1 4 W between pin 2 DMX and pin 3 DMX of the last fixture Using a cable terminator part number CABL90 will decrease the possibilities of erratic behaviour 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 Pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The Chart below details the correct cable conversion 5 Pin XLR socket En E GH teen A Ben n XLR socket in ignal screen Pin 2 Signal e Nea pin 2 3 Sana g Pin 4 Pin 3 Signal Pin 5 N C 5 Pin XLR socket Pin XLR ee 6 Pin 1 GND Screen Pin T GND D saree Pin 2 Sign Pin 3 Signal 2 Pin 5 NIC Clumen8 www elumen8 co uk2. and DOWN buttons Press the ENTER button once more to select the desired flash value and adjust by using the UP and DOWN buttons Speed values 00 99 00 slow 99 fast Flash values 00 99 00 slow 99 fast Programme 1 Static colour In this mode you can set the 60W Tri Par to any colour and any brightness When you are in the 01 STATIC mode press the ENTER button to change the brightness of each individual colour The R represents Red G Green B Blue and F strobe The two digits after it are the brightness 00 to 99 or in CF they are the strobe speed Example If you set R G and B all to zero the 60W Tri will have no LEDs showing blackout If you set R to 99 and G and B to zero the 60W Tri will be 100 Red Programme 2 7 colour change In this mode the 60W Tri Par will run through its 7 preset colours Programme 3 3 colour change In this mode the 60W Tri Par will run through its 3 colours Programme 4 colour fade In this mode the 60W Tri Par will fade through its 7 preset colours 2 Dimmer Response Press MODE until you get to Dimmer Response press the ENTER button and use the UP DOWN buttons to choose between Dimmer Response 01 or 02 01 Dimmer curve linear response LED 02 Dimmer curve linear response Halogen 3 DMX Channel Mode Press the MODE button until Channel is shown on the LCD d
3. lumen8 60W Tri Par 64 User Manual Code ELUM101 WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this equipment away from rain moisture and liquids SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution e Never remove warning or informative labels from the equipment Do not open the equipment and do not modify the equipment Do not connect this equipment to a dimmer pa
4. any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property Overview You should find inside the Elumeng8 carton the following items 1 LED 60W Tri Par 64 2 Instruction manual Technical Specifications DMX channels 3 or 5 selectable 1 x 60W Tri LED Static sound active master slave and DMX modes 2 dimmer curves 400Hz refresh rate 3 pin XLR in out sockets 4 push button menu with LCD display Beam angle 60 degrees Power supply 110 240V 50 60HZ Power consumption 86W Dimensions 390 x 240 x 195mm Weight 2 6Kgs Operating modes 1 Dimming 0 100 2 DMX 3 Master slave 4 Channel select 5 Dimming curves DMX OCCUPATION 1 GROUND 2 SIGNAL O O ANR RNA Cry DMX IN DMX OUT Overview LED DISPLAY MODE ENTER ur Down 90 Fuse Y Power Supply Operation Built in programmes To activate the units built in programmes press the MODE button to show 01 STATIC on the LCD screen Press the ENTER button to choose between the 4 built in programmes by using the UP and DOWN buttons Now press the ENTER button to select the desired speed and adjust by using the UP
5. ck Do not switch the equipment on and off in short intervals as this will reduce the system s life Only use the equipment indoors Do not expose to flammable sources liquids or gases e Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable Make sure that the available voltage is between 220v 240v e Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again If the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature e If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service Only use fuses of same type and rating e Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS WARRANTY One year from date of purchase OPERATING DETERMINATIONS If this equipment is operated in
6. isplay Press the ENTER button and use the UP DOWN buttons to select between 3 and 5 channel modes 4 Slave Mode To activate the unit in slave mode first you must link multiple units together and press the MODE button to show SLAVE MODE on the LCD screen Now on the master unit press the MODE button to select the desired mode and the slave units will now run in sequence with the master unit 5 Sound Active Mode To activate the units sound active mode first press the MODE button until the SOUND SENS is displayed Press ENTER and use the UP DOWN buttons to change the amount of sensitivity between 00 and 31 6 DMX Mode To enter the DMX mode press the MODE button to show DMX MODE on the LCD display Now press the ENTER button and use the UP and DOWN buttons to select the DMX address from 001 512 When you are happy with your setting press the ENTER button to confirm it DMX Charts 3 channel mode 0 255 Red 0 100 Green 0 100 Blue 0 100 Function Master Dimming 0 100 Strobe Slow Fast DMX 512 DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers ADMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located
7. on all DMX fixtures most controllers only have a data out terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA Cable DMX cable requirements for DMX operation The 60W Tri Par 64 be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output figure 1 Figure 1 Also remember that DMX cable must be daisy chained and cannot be split Notice Be sure to follow figures 2 amp 3 when making your own cables Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behaviour
Download Pdf Manuals
Related Search