USER MANUAL - Clean
Contents
1. USER MANUAL MODEL NUMBER BLX 200W Dual Manual Boot Scrubber Wet English Original Instructions USER MANUAL BLX 200W Dual Manual Boot Scrubber Wet THIN Cl j megrated Sanitation Intelligence READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT A CAUTION Avoid Personal Injury 0 Always follow plant and OSHA guidelines Avoid contact of cleaning agent with skin and eyes If contact occurs see MSDS sheet for further first aid measures Follow safety instructions of chemical manufacturer MSDS about the use of hygiene equipment All personnel using this unit must be familiar with the information contained in this manual Follow all installation and maintenance instructions Always wear appropriate footwear Secure or remove loose items on footwear Ensure solid footing and use both hands when operating the unit Specifications Frame 304 solid stainless steel construction Length 30 Width 30 Height 42 Requirements Electrical None Water Connection Cold Potable Water 35 PSI Minimum Pressure 50 PSI Maximum Pressure 100 Maximum Temperature Attention A backflow preventer must be installed in the water line to this unit Check local codes to ensure proper installation Slip Hazard Risk of injury USER MANUAL MODEL BLX 200W Page 2 of 10 11 25 2013 USER MANUAL B2. READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT Model BLX 200W Exploded View AN 0 2 ai USER MANUAL MODEL BLX 200W Page 8 of 10 11 25 2013 USER MANUAL BLX 200W Dual Manual Boot Scrubber Wet READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT Model BLX 200W Parts Callout BOLT HHC 5 16 1 X 3 4 55 Hex Finished 2 4 M1262 BRUSH AXED 10 1 2 X 3 BRUSH AXED 10 5 X REY 101 8 M1395 FOOT PLATE 1 200 FOOT PLATE 1 200 REV102 M1396 FRONT PLATE BLY MANUAL FRONT PLATE BLX MANUAL REV 1397 HANDRAIL BLX 200 HANDRAIL 1 200 REV 100 BRUSH BOX WLOMMNT BRUSH BOX WLDOMNT REW 102 2 M1392 BRUSH CUP BRUSH CLIP REY 100 M1393 AXED SIDE BRUSH AXED SIDE BRUSH REY 103 REAR PLATE BLX 200 REAR PLATE BLX 200 REY 101 racer BLX 200 DEBRIS TRAY DEBRIS TRAT REY 100 LABEL SLIP HAZARD LABEL CAUTION SLIP HAZARD 2 4 USER MANUAL MODEL BLX 200W Page 9 of 10 11 25 2013 USER MANUAL BLX 200W Dual Manual Boot Scrubber Wet READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT Model BLX 200W Dimensions Diagram USER MANUAL MODEL BLX 200W Page 10 of 10 11 25 2013
3. on the clip and rotate towards the rear of the unit Figure 11 3 Once unlocked the brushes can be removed for cleaning USER MANUAL MODEL BLX 200W Page 6 of 10 11 25 2013 USER MANUAL BLX 200W Dual Manual Boot Scrubber Wet 01 megrated Sanitation Intelligence READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT Operation Instructions Start Up After completed installation of the unit 1 Ensure the brushes and footplate are properly secured in their correct positions Turn ON water supply to unit Before placing footwear into the unit test that the unit is working properly by stepping on the footplate and making sure water sanitizer sprays from spray bars 4 The unit is now ready for use Operation Before beginning unit operation ensure solid footing and use both hands when operating the unit 1 To begin unit operation step onto the footplate The plate will push down on the valve which will turn on the spray bars for as long as it is held down 2 Place one boot in the unit at a time Slide boot back and forth multiple times so every part of the boot contacts with the brushes 3 Once the first boot is clean repeat process with the second boot 4 If boots are extremely dirty it may be necessary to perform multiple cleanings WARNING Always wear appropriate footwear Secure or remove loose items on footwear to prevent entanglement WARNING All personnel
4. 3 RECOMMENDED INSTALLATION VENTURI INJECTOR NOT INCLUDED WATER SUPPLY _ 35 PSI MINIMUM PRESSURE 100 F MAX TEMPERATURE NOTE INJECTOR MUST 2 MINIMUM FLOW BE MOUNTED WITHIN 10 FT OF BOOT SCRUBBER 3 8 OD 0 POLYETHYLENE TUBING CHEMICAL SUCTIONLINE NOT INCLUDED CHEMICAL CONTAINER INCLUDED Figure 4 USER MANUAL MODEL BLX 200W Page 4 of 10 11 25 2013 USER MANUAL BLX 200W Dual Manual Boot Scrubber Wet READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT General Overview Handrail Installation Instructions 1 Place handrail through the mounting brackets on each side of the unit Figure 5 2 Use two 1 2 wrenches to tighten the bolt through the locknut securing the handrail in place Figure 6 amp Figure 7 3 Repeat this process for all 4 bolts on each side of the unit 8 bolts total Figure 8 Note Do not over tighten bolts or deformation of sheet metal may occur Figure 8 USER MANUAL MODEL BLX 200W Page 5 of 10 11 25 2013 READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT General Overview Footplate Installation Instructions 1 Align Footplate on the front of the unit 2 Make sure the notches on the plate line up with the tabs on the unit 3 Figure 9 shows proper footplate placement Brush Removal Instructions 1 The brushes are held in place by the brush clip at the front of the unit Figure 10 2 To remove the brushes pull up
5. LX 200W Dual Manual Boot Scrubber Wet READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT General Overview Installation Instructions 1 Set unit in desired location 2 Aspects to consider when deciding on placement e Room for entering and exiting Traffic flow for unit operation e Emergency exit paths or egress in case of emergency e Head room for personnel while using the unit e Connections for water 3 Once the unit is in the desired location use a level to make sure the unit is stable and level in all directions Make sure the location is a flat surface Figure 1 Figure 1 Securely fasten unit the floor with concrete anchors and bolts through the 4 mounting brackets Circled in red in Figure 1 amp 2 WARNING IF UNIT IS NOT SECURELY MOUNTED TO FLOOR UNIT CAN TIP OVER AND CAUSE PERSONAL INJURY Figure 2 USER MANUAL MODEL BLX 200W Page 3 of 10 11 25 2013 USER MANUAL BLX 200W Dual Manual Boot Scrubber Wet CleanLc READ INSTRUCTIONS BEFORE OPERATING EQUIPMENT General Overview Plumbing Setup Attention A backflow preventer must be installed in the water line to this unit Check local codes to ensure proper installation e Use 3 8 OD polyethylene tubing to connect water or chemical supply to solution inlet fitting on boot scrubber Figure 3 e See Figure 4 for recommended installation Note Unit needs minimum 35 PSI and a 2 GPM connection to operate Figure
6. using this unit must be familiar with the information contained in the user manual Follow all installation and maintenance instructions WARNING Use only for intended use as described in this manual A WARNING Always follow safety precautions and obey warning labels Failure to do so could result in injury or death USER MANUAL MODEL BLX 200W Page 7 of 10 Shut Down for Cleaning Washdown 1 Shut off water line to unit and depressurize line 2 The unit is ready to be cleaned Cleaning Washdown 1 Remove the footplate from the unit 2 Unlock the brushes from the frame and lift them out 3 The brushes and footplate can be washed individually in a COP tank or wash machine and the frame can be washed by conventional means BLX General Maintenance Instructions The below maintenance procedures are recommended for normal use Units which see a high amount of daily use should be inspected more frequently as necessary Weekly e Check unit for proper valve function e Inspect brushes for damage or wear Check for missing or deformed bristles e Inspect plumbing for damage e Ensure solid mounting to floor Monthly e Check all fasteners to ensure they are tight e Ensure warning labels and decals are present and in good condition e Inspect valve for damage Quarterly e Inspect structure for cracked welds or bent components 11 25 2013 USER MANUAL BLX 200W Dual Manual Boot Scrubber Wet
Download Pdf Manuals
Related Search