User Manual - DCS-550M Master SERIES2 ver2
Contents
1. 19 J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER D PTRRRics SECTION 4 Menu Operations Remote Mode In a multi Master intercom system there may be times when a Master station will be left unattended leaving some incoming calls unanswered The Remote Mode menu FIGURE 14 allows the choice of those incoming unanswered calls to after a preset time has passed be automatically diverted to the next higher level Master When first switched on the Master will either automatically go into either remote or idle modes depending on the options saved by the operator For more information about remoting see next page e When the Master is first turned on it will either automatically go into either remote or idle modes depending on the options saved by the operator e Press the REM or END key to turn off the remote function if enabled To disable the remote function completely select Disable REM Key option from the menu selection e To otherwise enable the remote function press the REM key e The AutoRem 10 min AutoRem 2 min and AutoRem 12 sec menu options are selected as the amount of time that passes on an unanswered incoming call before the Master automatically goes into remote mode FIGURE 14 Remote Mode menu option DIGITAL CALL SYSTEM i ELECTRONICS Use the UP DOWN keys to select the Remote Mode menu option Press ENTER to begin END Press the END key to return to the2. 27 28 De Isolate Slave c ccccccccccccsccecocscccsscenccccccenssccecensvcccconceccesocccecetesceccersssseces 20 Aux Channel Set SECTION 5 Volume Adjustment Levels 0 32 UE a wen Te a 33 wen n 34 SECTION 6 Alarms NA A A A seein 35 n 35 268 Montague Road West End Queensland Brisbane Australia 4101 Web http www jacques com au J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER Phone 61 7 3844 1103 Fax 461 7 3844 1078 Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 3 DIAG QUES os J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 1 Overview The DCS 550M Series 2 Master The Jacques DCS 550M Series 2 Master is available as either a standalone or desktop Master console It is available as an option to the Jacques PCC 550M PC Master FIGURE 1 shows the front panel and switch layout for the Jacques DCS 550M Series 2 Master unit The main display comprises of a custom two lined LCD character display sizing sixteen 16 large characters each measuring 8mm high x 5mm wide All user function menus and calling information are clearly displayed on this screen Important Note Some of these user function menus may not be enabled depending on specific site installation criteria If they are not enabled they
3. Any connected Devices Slaves Masters etc are not responding or goes offline Any connected Concentrator type Slave has been tampered with Any connected Slave has a stuck CALL button BtnFail or CALL button has been pressed for longer than 4 seconds The Remote CPU Controller has failed or it cannot Remote switch The audio path between any connected Slave s Speaker and Microphone has failed Whenever a Lower Master has been Remote Switched Remoted End an Alarm If an Alarm is displayed the Operator can quickly stop and reset it by pressing the END key Example FIGURE 28 Tag 1004 a Slave has a failed microphone which quickly prompts the following MicFail Alarm message 1004 MicFail END Press the END key to clear the Alarm message 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 35 D JACQUES J acques Electronics Pty Ltd ELECTRONICS USER MANUAL JACQUES DCS 550M SERIES 2 MASTER O copyright 2002 JACQUES ELECTRONICS Pty Ltd Jacques Electronics Pty Ltd reserves the right to continually improve products by updating any equipment specifications document context and design styling and then passing this information onto this document 268 Montague Road West End Phone 61 7 3844 1103
4. Queensland Brisbane Australia 4101 Fax 461 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 36
5. e Use the star key to toggle between these two values e Use the UP and DOWN keys to change the values e Once the values have been correctly entered press the ANSWER key to save these changes The display will show your new values for 3 seconds before it goes back into Slave selection screen l Slave Slave selection screen The top line displays the tag number of the Slave last used You can either press the ANSWER key to edit the same Slave in case you made a mistake before or enter a new Tag number as before Tag numbers can be in the range from 1 to 8191 If you enter number 9999 the selected channel number and volume level will apply to all local intercoms To exit and save all changes press the END key 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 461 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS a 31 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 5 Volume Adjustment Levels Aux Channel During the System Idle operation no calls the Master console plays the selected Auxiliary Audio Channel through its internal speaker The Auxiliary Audio Channel volume level or Aux Vol can be adjusted accordingly by the Operator Note The Auxiliary Audio Channel volume level can ONLY be adjusted dur
6. 5678 and then press the ANSWER key Scroll through the tag list by using the UP and DOWN keys and then press the ANSWER key Slave D678 The display changes to dac Ch 1 Vol 5 Continued next page 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 30 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Aux Channel Set continued Slave 5678 Ch 1 Vol 5 Slave 5678 is the selected Slave s Tag number Ch 1 is the current channel selection value Channels can have one of four values they are e OFF There are no auxiliary audio channels selected When this is set the volume selection disappears from the screen e Auxiliary audio channel number has been selected e 2 Auxiliary audio channel number 2 has been selected e 3 This is reserved for future use Vol 5 is the current volume level value Volume levels can have one of eight values they are e OQ no volume or speaker mute e CU 27 3 4 5 6 7 Slave speaker volume levels Level 1 is the softest level Level 7 is the loudest level To change the settings The Ch and Vol Values can be changed in this screen
7. Device Class type Code types 1 Descriptor Example CELL 1 A Descriptor is another software address identifier code used to identify the Device They are displayed on the LCD screen It is text up to 16 characters long to fit within the 16 character LCD screen size stored inside the EEPROM memory chip located on the actual Pro Slave PCB or inside the Concentrator unit when using Concentrator Slaves Descriptors are NOT changeable by the Operator and can only be changed by a Technician from the Setup menu see separate JACQUES PC Master Technical Manual and then only from a Jacques PCC 550M PC Master unit usually the Highest Level Master Station 2 List Tag Example 3 List Tag numbers are numbers between 1 and the last Tag found in the networked intercom system They are a counter value that simply lists the place a Tag is within the Tags list Therefore as you scroll through the Tags this number will increment or decrement accordingly Every Device has a different List Tag number 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 5 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 1 Overview Code types continued 3 Tag Example 130 A Tag can be des
8. Slave produces an Alarm return to the Alarm 4 Slave sends Alarm message to EN 2min Delay Delay screen Master N a Master displays Alarm S 2 Operator clears Alarm on Master l a No Delay a x minutes later the Alarm message b cM will reappear at the Master IF the Alarm is not cleared at the Slave The No Delay setting will allow predetermined Delay times on Alarm messages sent from the Slaves Button Stuck every 2 minutes Tamper every 20 seconds 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS a 24 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Relay Settings The DCS 550M Master can switch up to two individual Relays which are located on the Slave Stations The relays need to have been correctly initialised from the Relay Settings menu see separate Jacques DCS 550M Technical Manual Note The Slave Station Relays can only be energized during a Call Connection Connect the Call 1 CALL button is pressed on a Slave The Relays are installed on the Slave PCB 2 The DCS 550M Master answers the call by pressing the ENTER key The Call is now connected As soon as the Call is connected the Slave Relays can be activated
9. e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 29 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Aux Channel Set The Aux Channel Set menu FIGURE 24 is used to allow the operator to change the auxiliary audio channel number and volume level for any connected Slaves directly from the Master About Auxiliary audio channels There are two auxiliary audio channels present within the Jacques Intercom system Usually one channel will be connected to a radio tuner and the other to another audio source such as a CD player These two audio channels can each be individually activated and controlled via the Aux Channel Set menu The audio from the Aux audio channels are heard through the individual Slaves speakers The Aux Channel Set menu is used to set the audio channels and individual volume levels It is noted here that even once these levels are set from the Master the Slave can still override these settings if that Slave has separate Volume and Aux select buttons FIGURE 24 Aux Channel Set menu option DIGITAL CALL SYSTEM i ELECTRONICS Use the UP DOWN keys to select the Aux Channel Set menu option Press ENTER to begin Aux Channel Set 01 01 2001 12 00 Press the END key to return to the System Idle screen Select the Slave to be changed by either one of two ways Key in the correct Tag number of the Slave eg
10. 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 27 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Isolate Slave continued Scrolling through the Isolated Slaves If ISO is displayed on the top right hand side of the System Idle screen FIGURE 22 it indicates that there are one or more Slaves already isolated To quickly view these isolated Slaves go to the Isolate Slave menu and then press the ENTER key Scroll through the isolated Slaves by using the UP and DOWN keys FIGURE 22 ISO is displayed on the top right of the System Idle screen DIGITAL CALL SYSTEM ae ELECTRONICS Use the UP DOWN keys to select the Isolate Slave menu option Press ENTER to begin Press the END key to return to the System Idle screen Example j Scroll to 2 Isolated Slave Tag 3 I Cell 1 2 3 Slave l I Press the END key to 1 return to the Isolate Slave screen N L1 EXIT N AN 1 131 Slave Use the UP DOWN keys 4 E to scroll through the Isolated Slaves _ L Ekample Nun Scroll to 1 Isolated Slave Tag 131 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au E
11. Activation of the Slave Relays Default relay ON time setting The default Relay energise ON time is set to second This means that each relay will automatically energise on the Slave Station for 1 second when a Call is connected Changed relay ON time settings The energise ON time for the relays can be changed from the Relay Settings menu see separate Jacques DCS 550M Technical Manual If these settings have changed then the following rules apply If the relay ON time Os 0 seconds then e Press the A key Relay Iwill energise e Press the B key Relay 2 will energise e Ending the Call will de energise the Relay If the relay ON time Os 0 seconds then e Relay 1 will energise as per Relay Settings menu see separate Jacques DCS 550M Technical Manual e Relay 2 will energise as per Relay Settings menu see separate Jacques DCS 550M Technical Manual e Relay will de energise after the ON time xxs setting has expired End Call function The End Call function if enabled will energise a Relay on the Slave Station for xx seconds and then automatically End the call See separate Jacques DCS 550M Technical Manual Default End Call setting The default End Call setting is NO This means that this function is disabled 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 461 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND
12. com au e e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS e 7 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 2 Calling Functions Calling a Higher Level Jacques Master FIGURE 4 Calling a Higher Level Master DIGITAL CALL SYSTEM No calls System Idle screen Make sure that the screen is in the System Idle mode before sending any calls ELECTRONICS Make a call Press the A key to place a call to the Higher level Master This Master is now calling the Higher level Master waiting for the higher Master to answer the call When the call is answered from the Higher Master this Master will now operate as a Slave Therefore there is no PTT key The Operator can then speak into the microphone which is located inside the Master unit To disconnect and END the Call Press the END key to disconnect the Call and return to the System Idle screen 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 8 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 2 Calling Functions Calling a Group About Groups A Group is a combination of different Jacques Devices such as PA Ampli
13. kan Your settings have now been saved and will not need to be reprogrammed the next time this console 1s Press A key N A re powered Press END to return to the EN D System Idle screen System Idle screen DIGITAL CALL SYSTEM deske ELECTRONICS 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS a 16 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations CPU Radio The CPU Radio menu FIGURE 11 is used to change the two different Auxiliary audio channels These audio channels can be heard through the internal speaker of the Master By using the UP and DOWN keys the operator can select between enabling Auxiliary audio channel 1 Auxiliary audio channel 2 or no channels both channels off no audio Once selected press the ENTER key to save the selection and then press the END key to return back to the System Idle screen NOTE If your selection cannot be heard press the UP key to adjust the channel volume FIGURE 11 CPU Radio menu option DIGITAL CALL SYSTEM i ELECTRONICS Use the UP DOWN keys to select the CPU Radio menu option Press ENTER to begin EN D CPU Radio 01 01 2001 12 00 Press the END key to return to the System Idle sc
14. key to disconnect the Call is located inside the Master unit and return to the System Idle screen Tf there are multiple incoming calls the END key will end the current call and display the next call in the queue To answer that next call press the ENTER key Use the ENTER key to speak use the END key to end that call 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 461 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS a 11 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 3 Answer Functions Placing a call on Hold Incoming calls can be placed on Hold they stay connected but are not active when other incoming calls are present Only one call can be placed on hold at a time C Oo FIGURE 7 Multiple incoming calls using the call HOLD Function In this example two Jacques Slave CALL buttons are pressed Slaves with Tag s 10 and 500 The Master beeps to initiate these calls are waiting to be answered Incoming calls are present The screen will change to indicate the Tag number of the calling Slaves EG 10 500 Answer the first incoming call Press the ENTER key to connect the first call Slave 10 The call is now connected and is displayed as Block C CELL 2 The display shows the call
15. will not appear when you scroll through the menu list FIGURE 1 Front panel layout of the DCS 550M Series 2 Master User controls and functions Large LCD display backlit for easy viewing Sixteen user pushbuttons Internal Electret Microphone Eight function pushbuttons e odi ua Internal water resistant speaker 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 461 7 3844 1078 Web http www jacques com au Email jacques jacques com au e a DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 9 a e 4 3 JACQUES ES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 1 Overview Device Identification Codes The DCS 550M Series 2 Master displays Identification Codes that are used to represent Devices see FIGURE 2 Devices are attached Intercom Slaves or Accessories that make up the JACQUES Intercom System and are individually controlled by the Master Every JACQUES Device has to be registered within the operating software by means of dentification Codes These codes are critical for correct Device identification and operation within the Jacques intercom system and consist of four different individual codes DIGITAL CALL SYSTEM FIGURE 2 Example of four codes displayed on the LCD screen are CELL 1 Device Descriptor 3 Indicates the 3rd Tag on the list JACQUES 130 Device Tag number mue Slave
16. DOWN keys to increment and decrement the volume level in steps of four Call Connected screen Call has been answered Use the UP DOWN keys to adjust the Call Connected volume levels The Call Connected volume can be adjusted in steps of four O value is no volume or speaker mute 64 is the maximum value During the adjustment the display changes to the Call Vol volume adjustment screen The Call Vol volume adjustment screen will disappear when the key UP DOWN has been released 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e s DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS e s 34 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 6 Alarms The DCS 550M Series 2 Master constantly monitors all operations and connected Devices for any signs of failures or disconnections Upon sensing an error the Master will sound an alarm and display the relevant fault description on the LCD screen Alarm Codes The following table TABLE 2 shows the current list of Alarm codes that are displayed during a failure of any connected Devices The LCD screen displays the Tag and then the relevant fault code of the faulty Device TABLE 2 Alarm Codes ws Tagh and An Alarm will sound if Shows Tag and
17. MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS a 25 3 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Get Tags In a finished Intercom System the Master needs to find and validate all of the connected Devices Tags and Class ID This process needs doing only the once and then every time a new Device is added to the Intercom System The following FIGURE 20 shows how the DCS 550M Master finds the attached Devices When it finds a Device it then records its individual Tag Descriptor and Class ID and stores this information into its own internal Flash ROM This provides a database of all the Devices and Tags found within the Intercom System FIGURE 20 The following Get Tags procedure needs to be done when the Intercom System is first commissioned and then every time a new Device is added to the Intercom System DIGITAL CALL SYSTEM Use the UP DOWN keys to select the Get Tags menu option Press ENTER to begin Press the END key to return to the System Idle screen Press the 1 key to Get the Tags Press the key to Abort and Exit The Master begins to search all of the Tags and Descriptors in the Intercom System Requesting Tags Req Descriptors xx Tag s Found Save Tags Press the 1 key to Save the Tags 1 Yes No Press the key to Abort and Exit All of the Devices Tags Descriptors and Class ID s have now been saved into th
18. NUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 18 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Scroll Tag List The Scroll Tag List menu FIGURE 13 is used to view all Slaves Masters and other Devices that are connected to the Master unit This menu functions as a viewer only and NO changes can be made to the Tags Once in the Scroll Tag List menu the operator can scroll through the Devices by using the UP and DOWN keys Press the END key to return to the Scroll Tag List screen Press the END key again to return to the System Idle screen FIGURE 13 Scroll Tag List menu option DIGITAL CALL SYSTEM i ELECTRONICS Use the UP DOWN keys to select the Scroll Tag List menu option Press ENTER to begin Scroll Tag List 01 01 2001 12 00 Press the END key to return to the System Idle screen e e M Te Use the UP DOWN keys to ee L1 MASTER scroll through the Tags 1 2 CPU Examples only Actual content will be different to yours L2 MASTER 2 32 CPU keu CELL 1 7 3 131 Slave 2e Press the END key to return li YO ao to the Scroll Tag List Me n ici screen 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS
19. System Idle screen This setting is used to disable the REM key on the front panel of the Master stopping the UP DONN ann OO e operator to turn on off the Use the UP PM A remote function keys to select the n Disable REM key Ka following different pi S selections fi N Disable AutoRem T AutoRem 10 min These settings determine the amount of time that passes on an unanswered incoming call before the Master automatically a goes into remote mode BM iii Disable AutoRem will me disable this function AutoRem 2 min n e an 268 Montague Road West End Queensland Brisbane Australia 4101 Web http www jacques com au Ld Press the ENTER key to save the setting and return dl to the Remote Mode screen Phone 61 7 3844 1103 Fax 61 7 3844 1078 Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 20 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Remote Mode continued In a multi Master intercom system and a Master is remoted then that Master s operations are no longer controlled by the operator The calling operations are now effectively disabled AII Slaves and Devices are all now controlled from the next level up Master The following diagrams illustrates this FIGURE 15 shows the operators signal path between th
20. TURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 23 3 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Alarm Delay The Alarm Delay menu is used to set the properties of the Tamper Alarm and Button Stuck features that are built into the JACQUES RS485 Slaves See FIGURE 19 below for changing the Alarm Delay properties Note These Alarm features are only found with the JACQUES RS465 Slaves e The Tamper Alarm feature is used to alert the Operator on the Master display screen that a Slave has been pulled out of its mounting e The Button Stuck feature is used to alert the Operator on the Master display screen that a Slave has a jammed Call button pushed in FIGURE 19 The Alarm Delay menu selects the Tamper and Button Stuck Alarm options DIGITAL CALL SYSTEM i ELECTRONICS Use the UP DOWN keys to select the Alarm Delay menu option Press ENTER to begin Press the END key to return to the System Idle screen The Disable Alarm setting is used to completely disable the Alarm function The Master will not display Use the UP DOWN keys to select the different options These Delay settings determine the any Alarm messages at all amount of time that passes on a valid Alarm message to be resent to the 20min Delay Master IF the Alarm is not cleared 1 10min Delay i Press the ENTER key EG to save the setting and
21. USER OPERATING MANUAL tor tne JACQUES DCS 550M SERIES Il MASTER Publication version 2 March 2003 Intercom Master P EEIE C N nn Jacques Electronics Pty Ltd ABN 11 010 416 323 e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS a JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER In case of difficulty Should a fault become apparent in the system and simple checks have revealed nothing obvious please follow the procedure as laid out by your internal maintenance policy Itis essential that all faults be documented in an appropriate logbook for any future referencing For any further information please contact our office during business hours on any of the following numbers Phone 07 3844 1103 Fax 07 3844 1078 Alternatively contact us on the Internet Email Web page JACQUES ELECTRONICS PTY LTD ABN 11 010 416 323 Copyright 2003 The contents of this document may not be reproduced stored in a retrieval system or transmitted in any form by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Jacques Electronics Pty Ltd Jacques Electronics Pty Ltd reserves the right to continually improve products by updating any equipment specifications document context and design styling Always quote this manual publication version found on the front cover when enquirin
22. ad West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS e 22 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Set Date Time The date and time is maintained by an internal clock The clock has a backup battery that can maintain correct time for 3 or 4 days without power FIGURE 18 Set Date Time menu option set from the Highest Level Master DIGITAL CALL SYSTEM Use the UP DOWN keys to select the Set Date Time menu option Press ENTER to begin Press the END key to return to the System Idle screen Use the UP DOWN keys to select the New Date amp Time following different IDE 01 01 2001 12 0X selections of Seconds Minutes Hours es New Date amp Time Month and Day 01 01 2001 12 XO0 a New Date amp Time X1 01 2001 12 00 FE Ey n ET Save the correct time by pressing the A key Press the END key to exit back to the main menu 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFAC
23. cribed as one of the software address identifier codes to the rest of the system The Tag is stored inside the EEPROM memory chip located on the actual Concentrator type Slave PCB or inside the Concentrator unit when using Concentrator type Slaves Tags are displayed on the LCD screen Tags are NOT changeable by the Operator and can only be changed by a Technician from the Setup menu see separate JACQUES PC Master Technical Manual and then only from a Jacques PCC 550M PC Master unit usually the Highest Level Master Station 4 Device Class Example Slave Device Class numbers are numbers between 0 to 255 inclusive that are given to a Jacques Device They are used to describe the type of Jacques Device that 1s used with that specific Tag number described in one of the following ways see TABLE 1 TABLE 1 Device Classes JACQUES ELECTRONICS DEVICE CLASSES and DISPLAYS CLASS JACQUES DEVICE TYPES LCD DISPLAY n n Ualul ti a rime 1 9 4 Audio recorder Interface Recordr 5 ay Ocard OR 6 Slave Concentrator Concent 8 J Doo GateSave DoorsSiv e 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 461 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 6 3 JACQUES cs J acques Electroni
24. cs Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 2 Calling Functions This Section covers the following key areas of calling devices e Calling a Jacques Slave e Calling a Higher level Jacques Master e Calling a Group Calling a JACQUES Slave Note There are three types of Jacques Slaves available 1 Mini Slaves 2 Concentrator Slaves 3 Door Slaves Either type of Slave can be called using the following method However a Door Slave can only be called when the Door Call Answer and Special functions are enabled FIGURE 3 Calling a Slave EM No calls System Idle screen Make sure that the screen is in the System Idle mode before sending any calls ae ELECTRONICS Begin a call Press the CALL key to begin a call to a Slave CA a Enter the Tag number Type in the Tag number of the Slave you wish Slave with Tag 131 V to call T EG Slave 1 3 1 is entered and press the ENTER key The call is now connected The Operator can now hear the called Slave d Talk button To SPEAK to the Slave Press and hold down the ENTER key Speak into the microphone which is located inside the Master unit To disconnect and END the Call ak Press the END key to disconnect the Call and return to the System Idle screen 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques
25. e Flash ROM located inside the Master Press any key to Exit x Tags Saved Any key to exit 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 26 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Isolate Slave TheIsolate Slave menu FIGURE 21 is used to allow the operator to disable or isolate selected Slaves within an intercom system When a Slave is isolated it is effectively disabled from the system until it is re enabled from this same menu see next page A Slave may need to be isolated if for example a Cell or room is empty or if the Slave is faulty or damaged FIGURE 21 Isolate Slave menu option DIGITAL CALL SYSTEM Use the UP DOWN keys to select the Isolate Slave menu option Press ENTER to begin Y Press the END key to return to the System Idle screen In order to isolate a particular Slave that Slave s Tag number must be entered at the Isolate menu followed by the ENTER key Any number of Tags can be entered here r Example Isolate Tag 3 I Press the END key to Example Isolate Tag 131 i return to the Isolate Slave screen D o 5 268 Montague Road West End Phone 61 7
26. ectronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 2 Calling Functions No calls System Idle screen Make sure that the screen is in the System Idle mode before sending any calls Begin a Group call Press the CALL key and then the B key to begin a Group call Select the Group number The 16 dashes indicates the 16 different groups that are available for the Operator to select from The dash on the far left represents Group 1 The dash on the far right represents Group 16 They are in numerical order from left to right NOTE The last group s selected will appear on the screen as a The Groups are saved in memory after every Group call To change the groups you may have to delete or add a Group s Key in the required Group number Select the Group number by keying in that number EG Group 3 is entered To delete that Group example Group 3 Press the D key To add that Group example Group 3 Press the ENTER key To call that Group The selected Group Group 3 example is now confirmed by a star replacing the dash Press the CALL key to connect the call to the Group The call is now connected The Operator can now make the announcement to the PA Talk button To make the announcement to the PA Press and hold down the ENTER key Speak into the microphone which is located inside the Master unit To disconnect and END the Call Press the END key to disco
27. fiers and Slaves that are combined together to form a Group There are up to sixteen different Groups allowed and each one can be individually selected or all at once When a particular Group is selected by entering its group number between 1 and 16 all of those Jacques Devices within that Group become active This allows the Operator to make an announcement over a selected large area simultaneously This is referred to as a Group call FIGURE 5 see next page shows how to make a Group call It is important to note here that the Master will remember the last Group call number and will display it in the screen as a star If you want to add or delete a Group number from the last setting you will need to do so accordingly as shown from the FIGURE 5 next page diagram Continued next page 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 9 DPTRRRcs Calling a Group continued FIGURE 5 Calling a Group DIGITAL CALL SYSTEM gt ELECTRONICS the 3 Group j number Kw ou To delete a call Enter PA Grp To make a call To end a call F N D 268 Montague Road West End Queensland Brisbane Australia 4101 Web http www jacques com au 7 m2 J acques El
28. g about any further product information 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 2 DARRO Nics Contents SECTION 1 Overview he DCS 550M Series 2 Master 0 csccccsscosccececsescececceccssscceccesseeneces 4 Device Identification Codes eese rene nu 5 NX NEM I EC 5 SECTION 2 Calling Functions alline a JACQUES Slavel 0 ccccccccceccsscscsccecsonsscescescesnececsesssccceeenenosnces 7 alime a Hieher Level Master w deesive kounie vev ou sid eee low si ene os 8 NY AE AN W A PRE EN E AN FAN YE AE ONA LI 9 SECTION 3 Answer Functions HL 11 lt su 4 iciliulbalu i m 12 FN SERTEEE M 13 SECTION 4 Menu Operations elus Rire ONE e bo ca sa l a kr ka ks a e sp ek e n a kk piki 14 Hidden User menus cccscoscscoscscescsccscecaccscaccecsccscsccscscesescescscasesceseecs 14 A 14 A A A 2 15 A A n 16 17 18 Gerol Tap ETE 19 EEEN EAEE A 20 22 VEMM 23 O 24 25 Nu 26
29. ing the System Idle screen no calls FIGURE 25 From the System Idle screen press the UP DOWN keys to increment and decrement the volume level in steps of four DIGITAL CALL SYSTEM oystem Idle screen i ELECTRONICS Use the UP DOWN keys to adjust the Auxiliary volume levels The Auxiliary volume is adjusted in steps of four OQ value is no volume or speaker mute 64 is the maximum value During the adjustment the display changes to the Aux Vol volume adjustment screen After three seconds of setting the new value the display will return to the System Idle screen 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 32 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 5 Volume Adjustment Levels Call Waiting Tone During an incoming call the Master console plays a two tone sound through its internal speaker This is known as the Call Waiting tone The Call Waiting tone volume level or Beep Level can be adjusted accordingly by the Operator Note The Call Waiting tone volume level can ONLY be adjusted during an Incoming Call Call Waiting FIGURE 26 When an incoming call is present press the B C keys to increment and decrement the vo
30. key Monitor 01 01 2001 12 00 Example To monitor the Slave with Tag 131 Key in the Tag 1 3 1 and press the ENTER NOTE If nothing is heard increase the speaker volume by using the UP key Slave with Tag 131 is now being CELL monitored The Operator can hear all 1 131 Slave activity from this Slave 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 13 3 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations User menus The DCS 550M Series 2 Master has an internal menu select type operation These menus User menus are used by the Operator to setup and control all aspects of Calling operations including enabling disabling Remote Mode Alarms Radio channels Auto Call End etc The User menus are selected and used by the Operator however some menus can only be set by JACQUES technical staff before the Master is shipped out to the customer These menus are known as Hidden menus Hidden User menus Hidden menus are those menu functions that are not shown hidden within the User menu list These functions can only be enabled disabled by JACQUES technical staff Hidden menus allow the versatility of custom made functions that specific customer
31. lume level in steps of four Incoming Call is present The screen will change to indicate the Tag number of that calling Slave EG 130 The Call Waiting tone volume level can now be adjusted Use the B C keys to adjust the Call Waiting tone volume level C B key to increment volume C key to decrement volume The Call Waiting volume level is adjusted in steps of four O value is no volume or speaker mute 64 is the maximum value During the adjustment the display changes to the Beep Level volume adjustment screen The Beep Level volume adjustment screen will disappear after the Call has been answered 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 33 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 5 Volume Adjustment Levels Call Connect When the incoming call has been answered by the Master known as Call Connected the Master console plays the Caller through its internal speaker The Call Connected volume level or Call Vol can be adjusted accordingly by the Operator Note The Call Connected volume level can ONLY be adjusted once the incoming call has been connected FIGURE 27 When the incoming call has been connected press the UP
32. mail jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 28 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Isolate Slave continued De Isolate Slaves If ISO is displayed on the top right hand side of the System Idle screen FIGURE 23 it indicates that there are one or more Slaves already isolated At some time those Slaves will need to be de isolated to bring them back online into the intercom system To De Isolate these Slaves use the same procedure as the Isolate Slave function except that the Slave s Tag number must be followed by a D key instead of ENTER FIGURE 23 De Isolate Slave menu option DIGITAL CALL SYSTEM Use the UP DOWN keys to select the Isolate Slave menu option Press ENTER to begin Y Press the END key to return to the System Idle screen In order to De Isolate a particular Slave that Slave s Tag number must be entered at the Isolate menu followed by the D key y Any number of Tags can be Ta entered here KM j E De Isolate Tag 3 Bg Press the END key to E d return to the Isolate 4 Example De Isolate Tag 131 ra Slave screen B 8 0 D 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au
33. nnect the Call and return to the System Idle screen Phone 61 7 3844 1103 Fax 61 7 3844 1078 Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 10 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 3 Answer Functions This Section covers the following key areas of answering calls e Answering an incoming call e Using call hold e Monitoring a call Answering an Incoming call Refer FIGURE 6 The Jacques Slave CALL button is pressed within the Networked Intercom system initialising a call send function to the Master The incoming call can then be answered by the operator FIGURE 60 A Jacques Slave CALL button is pressed a call send function is sent to the Master The Master beeps to indicate a call is waiting Incoming call is present System Idle The screen will change to indicate Que 150 the Tag number of that calling Slave EG 130 Answer Incoming call Press the ENTER key to answer the incoming call The call is now connected Call display The display changes to show the CELL 1 actual Tag that has been answered yonn to EG CELL 1 1 12 i A The Operator can now hear the caller from the Slave Talk button To SPEAK to the caller Press and hold down the ENTER key To disconnect and END the call Speak into the microphone which EN D Press the END
34. ptor and Class ID information from the connected Devices within the Intercom System Isolate De Isolate Slave This menu allows the operator to Disable or Isolate selected Slaves from the intercom system When a Slave is Isolated it is effectively disabled from the system until it is Enabled again De Isolate from this same menu Aux Channel Set This menu allows the operator to change the individual Auxiliary audio channels and speaker volume levels of connected JACQUES Slaves 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 461 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS a 15 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Saving menu selections Some menus require the operator to select one of a multiple choice function list They are e CPU Radio e Remote Mode e Auto Call End Once selected that option needs to be saved The options from these menus are all very important as they determine specific power on functions See these individual menus for specific menu options These individual settings can be saved by pressing the MENU key and then the A key FIGURE 10 FIGURE 10 Saving your settings Select your preferred settings from the individual menus MENU Press MENU key Pul A L
35. ree level Masters all are in Remote Off mode This allows all three Masters to individually operate and control its own level Slaves and Devices FIGURE 16 shows the new operators signal path between the same Masters however the Level 2 Master is now in Remote On mode The operators signal path has now changed Level 3 Master now controls Level 3 Slaves and Devices as before as well as all of Level 2 Slaves and Devices because Level 2 1s in Remote On mode Level 1 Master still controls Level 1 Slaves and Devices as before FIGURE 15 FIGURE 16 Level 3 PC Master Level 3 PC Master De va e r ET RAT ANE ST AD A STENA LAN Ia s Rep rel ad go ou Bes ee eG i Di FE SAA gS Pa OK ET KA pa RE PAG Re x SW ES Moa e kwi SE PE OF ae ser p d H 3 Se ESTANDA ONA LAA A RUE Se SURG EIS Y SES fef 5eeoo 5e ga E A EO000 KR aki Level 2 DCS550M Master Level 2 DCS550M Master Remote Off MODE Remote On MODE MET tis gt rus S E s Kk 97 Mv ANNE ORE Tz AO ET EE P Ras by WR a ovr KA SUR ENT MES eco go e Pe pes ni N PES Te oa qe Nen E TS ALS sae pa y Mu SAN SM eh Da ki i 8OO0 ESE gas Re M 5 9e00 Level 1 DCS550M Master E PEEN Level 1 DCS550M Master a n TX s i He Sane 7 Sis FU pon a YS sy E AT aithie kita A ADORA JS SSUAD al k Y eL De yo e OSE Rie PRE OE yi ec ae Ee Be oe Y
36. reen Channel Off Both audio channels off no audio Channel Off Channel 1 Use the UP DOWN keys to scroll through the choices P the ENTER key t Channel 2 2 ids c UO ya save the setting and retur ya to the CPU Radio LEE screen 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 17 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Sys Info The Sys Info menu FIGURE 12 shows the current Master version software loaded as well as the Master controller version used This is used to identify current operating software versions Example of Sys Info screen display Yours may be different due to software upgrades FIGURE 12 Sys Info menu option DIGITAL CALL SYSTEM i ELECTRONICS Use the UP DOWN keys to select the Sys Info menu option Press ENTER to begin Display shows Master console version as well as Master controller version Console 1 00 Master 2 2 83 Press the END key to return to the System Idle screen 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MA
37. s remaining in the queue and in this example are displayed as Que 500 Call on Hold Press the HOLD key to place the active call Slave 10 on hold That call is now on hold and is displayed as 10 on Hold The display shows the calls remaining in the queue and in this example are displayed as Que 500 10 on Hold Que 500 Answer the next call Press the ENTER key to answer the next call The call is now connected and is displayed as Block A Gate Press the END key to disconnect that call There are no other calls in the queue but still one on Hold from before This is displayed as 10 on Hold 10 on Hold 01 01 2001 12 00 Press the HOLD key to re connect that call When finished press the END key to disconnect HOLD 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 461 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 12 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 3 Answer Functions Monitor a call About Monitoring A single Jacques Slave can only be monitored at one time Slave monitoring allows the Operator to listen in to the selected Slave FIGURE 8 Monitoring a call from the System Idle screen DIGITAL CALL SYSTEM i ELECTRONICS HOLD To activate the Monitor function press the HOLD
38. s require providing the advantages of easier operation less menus to setup and use and the benefit to upgrade and expand later Menu selections 1 Press the MENU key from the System Idle screen FIGURE 9 This will display the first User menu option CPU Radio 2 Use the UP and DOWN arrow keys to find the menu you require 3 Once the correct User menu is found press the ENTER key to enter into that particular menu function providing the Operator with other options for that menu function FIGURE 9 User menu selection from the System Idle screen DIGITAL CALL SYSTEM To display the menus press the MENU key from the System Idle screen i ELECTRONICS CPU Radio Then use the UP DOWN keys 01 01 2001 12 00 to scroll through the different User menus au Press the ENTER key to s enter the selected menu MN L Channel OFF 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 14 JACQUES J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Important Note Some of the function menus shown here in the User menu list MAY NOT BE ENABLED on your DCS 550M Master If they are not enabled they will not appear when you scroll through the menu lis
39. t SWA La CE RES Mi AC MESTRE KDE S eeoo 45 eeoo FILIUM a pe OR Be pee PP ORS Oe me tin Ok ec PY FI ME 268 Montague Road West End Phone 61 7 3844 1103 Queensland Brisbane Australia 4101 Fax 61 7 3844 1078 Web http www jacques com au Email jacques jacques com au e DESIGNERS AND MANUFACTURERS OF PROFESSIONAL ELECTRONIC SYSTEMS 21 3 JACQUES cs J acques Electronics Pty Ltd USER MANUAL JACQUES DCS 550M SERIES 2 MASTER SECTION 4 Menu Operations Auto Call End The Auto Call End menu FIGURE 17 is used to automatically disconnect an already connected call It disconnects after a preset time has passed and that there is no call activity detected FIGURE 17 Auto Call End menu option DIGITAL CALL SYSTEM i ELECTRONICS Use the UP DOWN keys to select the Auto Call End menu option Press ENTER to begin Auto Call End 01 01 2001 12 00 Press the END key to return to the System Idle screen Use the UP DOWN keys to select the KA following different selections Disable AutoEnd AutoEnd 2 min AutoEnd 10 min AutoEnd 30 min ON Press the ENTER key to These settings determine 4 A save the setting and return the amount of time that Sl Pd to the Auto Call End passes on an already E cdi screen connected call before the MO P Master automatically disconnects that call Disable AutoEnd will disable this function 268 Montague Ro
40. t and are known as Hidden menus Refer to JACQUES for more details User Menu list CPU Radio This menu switches ON or OFF the two Auxiliary audio channels which can be heard through the DCS 550M Master s internal speaker Sys Info This menu shows the current Master version software loaded and the Master controller version that it is connected to ocroll Tag List This menu displays all current and active Tags Slaves Masters and other Devices that are connected to the Master This is a viewer only function and no changes can be made to the Tags from this menu Remote Mode This menu enables or disables the Remote mode Once in Remote mode the Master 1s completely controlled by the next Higher Level Master All incoming calls will then be diverted to that Higher Level Master after a selection of preset times Auto Call End This menu is used to set the time that a call will automatically end if no further call activity is detected Set Date Time This menu allows the operator to change the RTC s Time and Date locally However the time and date will automatically be updated from a Higher level Master if used Alarm Delay This menu is used to set the properties of the Tamper Alarm and Button Stuck features that are built into the JACQUES RS485 Slaves Relay Settings This menu is used to activate the Relay switching properties located on the Slaves Get Tags This menu allows the operator to get Tag Descri
Download Pdf Manuals
Related Search