中性-User Manual V_2 修改 - Lightcast Public Safety
Contents
1. Mobile Phone Network Camera User Manual Stepl Input 3C ID Step2 Click Remote Step3 Input Password Step4 Connecting Monitor Button Step5 Connect Successful Steps of the remote monitor 21 Mobile Phone Network Camera User Manual 5 2 Video call Video call between two devices Dial among WAN network After MOBILE PHONE NETWORK CAMERA connecting to internet normally the icon of standby abnormal network connection will disappear the MOBILE PHONE NETWORK CAMERA is online state then you can make video calls after dial the 3C ID of the other device Dial among LAN network If two devices in same LAN you can make video calls after dial the last numbers of the IP address Example the IP address of device A or device B in LAN is 192 168 1 10 and 192 168 1 11 device A can dial 11 to make video call with device B Using mobile devices such as cell phone or tablet computer to make video calls with the device Boot up the application after normally installing client software to cell phone or tablet computer etc click on the dial screen and enter the 3C ID as required click video call button to make video call with the MOBILE PHONE NETWORK CAMERA If the video call fails please check whether the network of mobile device is normal Mobile Phone Network Camera User Manual Stepl Input 3C ID Step2 Click ideo Call Button Step3 Connecting Steps of the Cideo Call Mobile Phone Network Camera User Manual 52. ne a amp cs Monitor Call Playback Control Modify Media settings Security Settings Network Settings Click OK to trigger the wireless devices to learn Alarm settings mran Record Settings Remote settings 6 2 Wireless detector amp remote control A Delete a detector of a group of numbers click the associated digital and confirm to delete B Delete all detectors of a group of numbers long press the group name and confirm to delete 25 Mobile Phone Network Camera User Manual 7 FAQ and maintenance 7 1 FAQ If the problems are not listed please contact local service or call the HQ service we will try the best to serve you The MOBILE PHONE NETWORK CAMERA cannot boot up normally Possible reasons are as follows 1 The power supply is wrong 2 Switch power supply line is not in good connection 3 Switch power supply is damaged 4 The program updating is wrong 5 The front panel is damaged The MOBILE PHONE NETWORK CAMERA reboots automatically or stops working after boot up a few minutes Possible reasons are as follows 1 The input voltage is not stable or too low 2 The power of switch power supply is low 3 Frontal video signal is not stable 4 Bad heat radiator or too much dust or bad running circumstance of the MOBILE PHONE NETWORK CAMERA 5 The hardware of the MOBILE PHONE NETWORK CAMERA is damaged Mobile Phone Network Camera User Manual System cannot detect USB or Micro S
3. 1 Remote monitor You need correctly connect to the network before remote monitor For network setup please see 4 5 Main menu gt network setup Remote monitor between two devices The internet abnormal connection icon of standby interface will disappear after normal access to the internet and the system is online state Example when using device A to make remote monitor to device B the 3C ID is 1001 you need set remote monitor password for device B see Main menu gt general And set device A as follows press 1001 and dial it the dialog box will be popped up to remind you of entering access password press confirm button after enter password then device A can make remote monitor to device B Using cell phone or tablet computer to make remote monitor to the MOBILE PHONE NETWORK CAMERA You need download from APP Store in your mobile device first IOS clients can search and download from Apple APP Store Android clients can search and download it from Google Play Boot up the application after normally installing client soft ware to cell phone or tablet computer etc click on the dial screen and enter the 3C ID as required then click remote monitor button and the dialog box will be popped up to remind you of entering access password you can make remote monitor to this MOBILE PHONE NETWORK CAMERA after enter correct digital passwords If the remote monitor fails please check whether the network of mobile device is normal
4. APP receive the alert you can remote monitor the site directly Motion detection This option is turned on and when the system detects the mobile signal that reached a preset sensitivity by analyzing the video image motion detection alarm will be booted Buzzer You can set the alarm duration of system speaker when alarm appears 17 Mobile Phone Network Camera User Manual 4 7 Recording setup Set different record modes you can click main menu gt record to enter the record setup interface You can set three record modes manual alarm and timed The priority of the manual recording is the highest regardless of any recording modes once long press button it will enter manual recording mode The record LED indicator will blink during record state Manual Long press record button can manually control the opening and closing Picture 4 11 Record setup 1 Mobile Phone Network Camera User Manual Alarm When motion detection or outside alarm triggers system will automatically enter record state Record timing indicates that record duration after trigger the alarm Record Mode Alarm O Recording Time 1Min Picture 4 11 Record setup 2 Timed You can set the record time system will automatically enter record state during this time Record Mode Schedule Schedule 00 00 Picture 4 12 Record setup 3 19 Mobile Phone Network Camera User Manual 5 Remote monitor and video call 5
5. Video retrieval 13 Mobile Phone Network Camera User Manual Fast retrieval Enter the video playback interface you can search system video file of the day after press search button SJ directly If there is no video it will show no video file found Begin 2013 12 12 00 00 s End 2013 12 12 23 59 No file was found Picture 4 5 Video retrieval Accurate retrieval Move the cursor to adjust the starting and ending time the window will pop up the video file list which conforms to searching condition after press search button SJ press up down and left right buttons to move the cursor to select the target file then press button ok to play Begin 2013 12 12 00 00 End 2013 12 12 23 59 OS Picture 4 6 Video retrieval 14 Mobile Phone Network Camera User Manual Play During play state press left right buttons to finish fast forward and rewind operation and press up down buttons to switch different video files Press the button ox to stop playing Press right key for single frame playing during stop playing state Press button or can adjust the volume 4 5 Network setup Set network parameters you can click main menu gt network to enter the network setup interface IP IP Auto 192 168 10 116 Net WiFi AO spd gt Picture 4 7 Network setup IP Set system IP address you can automatically or manually set the IP address Through automatically set the IP address system will automati
6. 3 Recent call records and address book Press dial button and enter recent call records interface under standby state cd Recent B 10198 BW 10198 Contacts A A dial in A dial out e dial out but not sonnected S dial in but not onnesied a moniton be monitored A Move the cursor and choose call records press dial button can redial quickly press OK button can add the numbers to address book Move the cursor to address book and enter address book interface amp Recent Contacts x nam 012369 Move the cursor and choose the contact name it can be modified through pressing OK button long press OK button can delete the contact name 24 Mobile Phone Network Camera User Manual 6 Wireless learning code 6 1 Learning code with Wireless detector and remote control All the wireless detectors must learn code with the device for normal usage The specific operation as follows Please download and install APP from www camnoopy com android add the device to contact list after registration and successful login click contact name gt control gt defense setup for example to set up a door sensor as No 1 detector of the hall choose the hall click No 1 button the learning code dialog box will be popped up then the door sensor will be triggered and APP will remind that the learning is successful The No 1 button will turn to be light blue color A Demo Test Test i 3c 3c Test Time Settings
7. D card Possible reasons are as follows 1 The USB or Micro SD card line is not in good connection 2 The card slot is damaged 4 The USB port of main board is damaged I can not find the video files in local playback mode Possible reasons are as follows 1 The storage equipment is damaged 3 The storage equipment is damaged 2 The query condition is wrong 3 The video files to look up are covered 4 The recording is not on The local video is not clear Possible reasons are as follows 1 The image quality is too bad 2 The reading program is wrong bit rate is low and full screen mosaic during playback Normally the problem will be solved after reboot up the MOBILE PHONE NETWORK CAMERA 3 The storage equipment is damaged 4 The hard disk is damaged There is no audio signal in the surveillance window Possible reasons are as follows 1 It is not an active tone arm 2 It is not an active sound box 3 The audio lines are damaged 4 The hardware of the MOBILE PHONE NETWORK CAMERA is damaged Mobile Phone Network Camera User Manual The time is wrong Possible reasons are as follows 1 Setting is wrong 2 The battery is in bad connection or the voltage is too low 3 The oscillation is damaged The motion detect is not wrong Possible reasons are as follows 1 The motion detect area setting is not correct 2 The sensitivity is too low 3 Limited by some hardware edition The image is n
8. Mobile Phone Network Camera User Manual Please read instructions thoroughly before operation and retail it for future reference ENG Mobile Phone Network Camera User Manual Read and understand thoroughly this safety awareness amp instruction before using and keep it for future reference the device is called MOBILE PHONE NETWORK CAMERA in this text Safety Precaution Do not place heavy object on the MOBILE PHONE NETWORK CAMERA Do not let any solid or liquid fall into or infiltrate the MOBILE PHONE NETWORK CAMERA Do not disassemble repair or replace the parts of the MOBILE PHONE NETWORK CAMERA by yourself Using environment Please place and use the MOBILE PHONE NETWORK CAMERA between 0 C and 40 C Avoid direct sunlight or stay away from heat Do not install the MOBILE PHONE NETWORK CAMERA in damp environment Do not expose the MOBILE PHONE NETWORK CAMERA in smoky or dusty environment Do not drop the MOBILE PHONE NETWORK CAMERA and avoid strongly collision Please insure the MOBILE PHONE NETWORK CAMERA level installation in a stable workplace and prevent the MOBILE PHONE NETWORK CAMERA to be dropped Please install in well ventilated place Do not block the vents The MOBILE PHONE NETWORK CAMERA only can be used within the range of rated input and output Mobile Phone Network Camera User Manual 1 Product Introduction 1 1 Product Overview The MOBILE PHONE NETWORK CAMERA series is a type of excellent intellige
9. OBILE PHONE NETWORK CAMERA power supply Suggest using the UPS to protect the power supply under allowable conditions 3 2 Turn off Check and confirm the recording is stopped before turn off the MOBILE PHONE NETWORK CAMERA turn off the power supply switch to OFF or pull the rear panel power switch that can switch power Auto resume after power failure If the MOBILE PHONE NETWORK CAMERA is shut down abnormally it can automatically backup video and resume previous working status after power failure Insert the U disk or Micro SD card Please make sure the MOBILE PHONE NETWORK CAMERA is not in recording state before inserting the U disk or Micro SD card otherwise information will loss or storage equipment will be damaged Replace the battery Please save the setting information and turn off the power supply switch before replacing the battery The MOBILE PHONE NETWORK CAMERA uses button battery Please check the system time regularly if the time is not correct you need replace the battery Suggest replacing the battery every year and using the same type battery Note The setting information must be saved before replacing the battery otherwise information will lose Mobile Phone Network Camera User Manual 3 3 Standby state Turn on the MOBILE PHONE NETWORK CAMERA and enter standby state the system standby is shown as below 013 1212 Y Ree DAY Picture 3 1 Login interface Icons meaning under standby state USB det
10. c access to IP by DHCP Through manually set the IP address you can manually set the IP address system will automatically determine the network segment of IP address you only need manually set the last one of IP address internet According to access way to network to choose wired or WIFI connection to internet Equipped with wire system will connect internet through the wired network Using WIFI system will search WIFI and set the connection accordingly the connected internet name will be shown after successful access and WIFI connection icon will be shown in standby interface 15 Mobile Phone Network Camera User Manual TP LINK_37BD24 iT V D7B8 TP LINK_2CF0DC ChinaNet D7B8 yimei fey in Picture 4 8 WIFI setup 4 6 Alarm setup Set alarm parameters you can click main menu gt alarm to enter the alarm setup interface You need pre start the defence system before using alarm function system enter defence state after long press button m in 15 seconds defence indicator will constant light alarm cam com Bunding ID 1010056 7 Motion Detection xp Buzzer Picture 4 9 Alarm setup Send e mail When there is alarm or alarm linkage of capture images you can send specific alarm information or capture images to given e mail address 16 Mobile Phone Network Camera User Manual le Picture 4 10 Email alarm Burned ID When the alarm occurs you can send an alert to the given APP ID when the user s
11. company The manual is for the number of products for reference the specific operation of each product is not an exhaustive if you have any difficult problem please contact the company customer service department
12. ection icon Micro SD detection icon WIFI connection icon Internet connection icon Sever abnormal Motion detection icon 3C smart card detection icon Miss call connection icon Mobile Phone Network Camera User Manual 4 Main menu Press button ok the system main menu is shown as below You can operate and set each function in this menu System Playback a Network Alarm Record Picture 4 1 Main menu interface Mobile Phone Network Camera User Manual 4 1 Main menu navigation Play Function Overview Set the basic parameters of the system Update and maintain system and show related information of the system Search and play video files Network Set the basic parameters of the network Alarm Record Set the basic parameters of the alarm Set different record modes 4 2 General setup O 2013 12 12 18 43 A Language English Format PAL Password kkk Picture 4 2 General setup interface 11 Mobile Phone Network Camera User Manual Set the basic parameters of the system please click main menu gt general to enter the general setup interface Time setup Set the system date and time Language setup Set the system language Video format According to PAL or NTSC used in different areas set the video format of the system Access password Set the password of network remote monitor the password only can be numbers You must set acces
13. irst please check whether there is any visible damage to the package appearance The protective material used for the package of the MOBILE PHONE NETWORK CAMERA can sustain most accidental clashes during the transportation Then please open the box and get rid of the plastic protective coating Check whether there is any visible damage to the MOBILE PHONE NETWORK CAMERA appearance 2 2 The front panel and rear panel The key function specification in the front panel and the interface specification in the rear panel are described in details in the manual Please check carefully the product model in the bottom plate or in the rear panel film whether is accordant with the model you ordered The label in the bottom plate or in the real panel is very important for after sales service please protect it carefully Please provide the product model and serial number in the label before you contact our after sales Mobile Phone Network Camera User Manual 2 3 The front and rear panel key function Camera Piolot lamp From left to right are Fara fe ae A Network Defence Recording Alarm Mobile Phone Network Camera User Manual The front button operation function Num Button name Mark Function Number button 0 9 Input the number key during user input state Short press to decrease the volume during video call or playing state x Short press to delete text during edit state Long press to record stop recording during man
14. nt home product specially designed for digital field It introduces embedded LINUX operating system which is more stable It introduces the technology of standard H 264 mp video compression format and G 711A audio compression format which insure the high quality image low bit rate and single frame playing It introduces Cloud link P2P network transmission technology which achieves strong network data transmission ability and remote control ability It introduces wireless learning codes technology and wireless detector to construct a strong alarm system 1 2 Main functions Video call It can realize the video call not only between two MOBILE PHONE NETWORK CAMERA but also among smart phone tablet computer and MOBILE PHONE NETWORK CAMERA Record function After inserting U disk or Micro SD to MOBILE PHONE NETWORK CAMERA it can realize simultaneous storage and recording of audio and video and different recording mode such as manual recording alarm recording timing recording can be selected You can search video files intelligent on the device and playback video on the screen directly Remote monitor It can achieve remote monitor by using mobile APP to dial 3C number 2 Mobile Phone Network Camera User Manual Wireless alarm It introduces wireless learning code and wireless detector to construct alarm system and also email alarm function is Supported 2 Open package inspection and cable connection 2 1 Open package check F
15. ot clear or there is no image in network preview or video file playback state Possible reasons are as follows 1 Network is not stable 2 The user machine is resource limited 3 The user has no surveillance purview Network connection is not stable Possible reasons are as follows 1 Network is not stable 2 IP address is conflicted 3 MAC address is conflicted 4 The network cad of the computer or the computer is bad 28 Mobile Phone Network Camera User Manual 7 2 Maintenance Please use the MOBILE PHONE NETWORK CAMERA in dry environment so that the MOBILE PHONE NETWORK CAMERA can work long term and stably The damp dust in the circuit board will cause short circuit which will interferes the MOBILE PHONE NETWORK CAMERA normal running or damages the MOBILE PHONE NETWORK CAMERA Please keep the grounding well done to prevent the video or audio signal interfered and the MOBILE PHONE NETWORK CAMERA from static or inductive electricity Please keep the MOBILE PHONE NETWORK CAMERA away from the heat resource Please keep the MOBILE PHONE NETWORK CAMERA ventilated for better heat radiator Please check and maintain the system regularly This manual only for the basic operation please refer to the electronic manual CD ROM for detailed operation Equipment updated in real time there is no notice if upgraded If you have doubt or dispute for product description all will be subjected to the ultimate interpretation of the
16. s password for the system in the first time otherwise the remote monitor cannot be used 4 3 System setup Update and maintain the system please click main menu gt system to enter the general setup interface C gt ORINE amp 3C ID 58400 Version_ 00 02 00 35 Picture 4 3 System setup interface 12 Mobile Phone Network Camera User Manual Restore factory Restore system to factory setting System update JYou can update and maintain the system when there is system software need to be updated There are two ways local update and cloud update Local update Copy the update file to U disk or Micro SD card then insert U disk or Micro SD card Press update button Band then OK press button to update after system detect the update file the system will reboot up after finish updating Cloud update Under network state press the update button Meal then the system will automatically detect whether there is file need to be updated Press button sas the system will automatically upload and update after detect the new version The system will reboot up after finish updating 3C ID The 3C ID number will be shown here after insert 3C smart card to the device Version information The current system version information is shown 4 4 Play Search and play video files you can click main menu gt play to enter the video playback interface Begin 2013 12 12 00 00 End 2013 12 12 23 59 ISS Picture 4 4
17. ual record mode Short press to increase the volume during video call or laying state Ctrl shift a d fense Short press to switch input method during edit state Long press to do defense cancel operation Short press to dial video call during standby state Dial preview Long press to enter real time preview during standby mode Hang up call during video call Hang up Exit Back to above level menu and exit current state Direction button Main menu confirm key Mobile Phone Network Camera User Manual Remove the cursor by up and down buttons when the main menu or submenu is popped Add or decrease number during edit state Change the setting in the menu Play last or next video file by up and down buttons during the playback state Move the cursor by left and right buttons when the main menu or submenu is popped Play in the multi low or multi fast video during the playback state Confirm Enter main menu Mobile Phone Network Camera User Manual 2 4 The rear panel C Network interface Q WIFI ant interface USB interface D 3C smart card interface Micro SD Power interface 3 Basic operation 3 1 Turn on Plug the power supply and turn on the power supply switch to ON the MOBILE PHONE NETWORK CAMERA enters the system Mobile Phone Network Camera User Manual Suggest using the stable input voltage and power input ripple with less interference to make sure the M
Download Pdf Manuals
Related Search