User Manual - lunatico.es
Contents
1. Please check as the installation program will try to install it under Maxpilote GNS instead GNS 1 0 0 1 user s manual 23 Oct 23 2013 5 Setup Good Night System ME ES Select Destination Location Where should Good Night System be installed A Setup will install Good Night System into the following folder To continue click Next f you would like to select a different folder Browse C Maxpilote GNS Ls At least 2 0 MB of free disk space is required you ll have to manually remove the trailing GNS from the installation folder GNS 1 0 0 1 user s manual 24 Oct 23 2013 5 Important smartphone usage notes leave your smartphone fully charged or plugged to a suitable power supply it won t warn you if the battery runs out dim the screen to save battery check your sound settings if you are using the audible alarm the app won t run in the background Communications are not reliable at all while in the background so it is mandatory to leave the app running the monitor screen visible In fact for OS devices if the app is sent to the background it will stop Just in case here s an explanation of everything in the monitor screen Monitor Status of the communication with UP E the observatory s PC Last session message received Imaging M42 9 12 from the PC automation Timeout o a Current countdown shown in red as itis approaching 0 below 32. GNS User s manual By Lun tico Astronom a GNS 1 0 0 1 user s manual 1 Oct 23 2013 9 GNS 1 0 0 1 user s manual INDEX Preface Installing and checking the PC program Smartphone installation Real life integration 4 1 CCDAutoPilot 4 2 CCDCommander 4 3 ACP Observatory Control Software 4 3 1 ACP Observatory Control Software 4 3 1 a ACP User Actions 4 3 1 b Weather Safety script 4 3 1 c Autofocus script 4 3 2 ACP Scheduler 4 3 2 a Startup script 4 3 2 b Shutdown script 4 3 2 C Special Autofocus script for Scheduler 4 4 Maxpilote Important smartphone usage notes Windows application options Tight integration Pending features and wishlist PC Smartphone System General Last notes 2 Oct 23 2013 1 Preface Thank you for your interest in the Good Night System our innovative product to make your long imaging sessions easier Features that set apart the Good Night System it does not rely on SMSs or emails to the contrary the smartphone constantly plays an active role safety goes first in some cases you may be warned when no real danger exists most probably if the time allotted for a task is exceeded because it was too short or the communications go down but provided the smartphone is powered it will wake you up if something goes wrong or seems to go wrong both the Windows application and the smartphone app are small and reliable by design and have be
3. CreateObject FireflyEXP Help if FireFly Connected then while FireFly RelayRead 6 1 FireFly RelayOpen 6 wend Util Console PrintLine Mirror fan switched off end if Dim wD GNS 1 0 0 1 user s manual 17 Oct 23 2013 set wD CreateObject GNS OWL wD NewMsg Target starting wD NewTimeout 300 set wD nothing TargetStart True End Function Function TargetEnd Plan Target NextTarget Util Console PrintLine useraction TargetEnd called Dim wD set wD CreateObject GNS OWL wD NewMsg Target finished wD NewTimeout 1 set wD nothing TargetEnd True End Function Function SlewStart RightAscension Declination Util Console PrintLine useraction SlewStart called Dim wD set wD CreateObject GNS OWL wD NewMsg Slewing wD NewTimeout 180 set wD nothing SlewStart True End Function Function SlewEnd Util Console PrintLine useraction SlewEnd called Dim wD set wD CreateObject GNS OWL wD NewMsg Slew finished wD NewTimeout 1 set wD nothing SlewEnd True End Function Max slewing time incl meridian flip Reset slewing timeout Function ImageStart Interval Binning Subframe FilterNum ForPointing Util Console PrintLine useraction ImageStart called Dim wD set wD CreateObject GNS OWL wD NewMsg Imaging wD NewTimeout Interval 120 set wD nothing GNS 1 0 0 1 user s manual Add buffer for dow
4. Hitz for writing the section on ACP integration John Smith author of CCDAutoPilot for his nice integration of the GNS in his software Matt Thomas author of CCDCommander for allowing me to post the messages about the system in his support list The Mosync team for their great cross development tool and their continuous support and of course everybody in the beta test team for their contributions and patience Revision history 1 0 Original manual 1 0 0 1 More clear 32 64 bits explanations more detailed Maxpilote installation updated everything related to CCDAP v5 New message vbs script GNS 1 0 0 1 user s manual 29 Oct 23 2013
5. connected nothing to do end if Console PrintLine Trying to park scope wD NewMsg Parking scope wD NewTimeout 300 Timeout for parking roof close Telescope Park Some magic triggers the dome roof close at this point if Dome ShutterStatus lt gt 1 then wD NewMsg Alarm Roof still open wD NewTimeout 0 else wD NewMsg Weather abort finished wD NewTimeout 1 end if wD NewMsg Weather abort finished wD NewTimeout 1 set wD nothing Console PrintLine Finished End Sub Screen shot after weather safety script Dome is already closed at this time GNS 1 0 0 1 user s manual 20 Oct 23 2013 Configuration 4 3 1 c Autofocus script A timeout should also be added to the AutoFocus script to catch faults in FocusMax File PROGRAMFILES X86 Z ACP Obs Contro l scripts AutoFocus vbs Somewhere after the filter check line 49 I added a timeout of 300 seconds Dim wD set wD CreateObject GNS OWL wD NewMsg Autofocus wD NewTimeout 300 Before terminating this script look for SUP Terminate the timer should be cleared wD NewMsg Autofocus finished wD NewTimeout 1 set wD nothing 4 3 2 ACP Scheduler One can also edit the Startup and Shutdown scripts from ACP Scheduler to trigger some timeouts here 4 3 2 a Startup script File PROGRAMFILES X86 ACP Scheduler StartupObs js Find the snippet below and create a timeout of a few minutes in within the
6. problem before giving up and issuing a warning Watchdog Timeout this is the watchdog watch owl time If for any reason the smartphone does not get any meaningful communication from the PC for the specified amount of time it will wake you up Sound and Vibration just refer to the means of warning you Leave at least one active Just touch the Validate button and from the main screen now press Monitor 2 Remember the behavior of the watchdog is changed in the free version GNS 1 0 0 1 user s manual 9 Oct 23 2013 If the network is correctly setup firewall included we ll go to the main monitor screen and in a few seconds the communications will go UP and a forced alarm will fire It is forced because unless you performed all these steps in less than 2 minutes we setup a 120 sec time earlier testing the PC application the timeout reached 0 long ago What if the communications don t go UP and you get other kind of error watchdog or too many conn tries Well that means the smartphone is not able to talk to the PC There are a number of possible causes some firewall program is preventing the PC to accept incoming communications completely disable the firewall and try again If this works you should enable the firewall later but adding a rule or exception for the GNSUI exe program The network settings are not correct This is a more complex matter I see three different sit
7. take effect Last you are not limited to the supplied scripts even if everything can be done with just the update vbs one should you find it useful just edit any of them with a suitable editor the standard notepad will do nicely to issue personalized messages easily GNS 1 0 0 1 user s manual 26 Oct 23 2013 7 Tight integration Scripts are just a means of updating the GNS from the outside this can be done directly from other programs just calling the appropriate methods of the GNS OWL class GNS OWL There are two such methods NewMsg takes a string argument and just updates the displayed Status NewTimeout takes a long integer argument and updates the timeout if timeout gt 0 the behavior is normal if timeout 0 then an alarm is issued as soon as it is received by the smartphone if timeout 1 then the count down is stopped and the system is waiting but the watchdog is still active if timeout 2 then a switch off is performed it is understood the end of the session has been reached There s no need to launch the user interface application GNSUi exe it will be launched if needed upon creation of the GNS OWL object I m absolutely confident any programmer will find this explanation more than enough but of course I ll be glad to help GNS 1 0 0 1 user s manual 27 Oct 23 2013 8 Pending features and wishlist At the moment of this writing I am aware of
8. telescope slew plate solve focus and actual imaging The duration of course varies up to a few hours Last for the end of the session ccd warm up telescope park roof close As my observatory is at home I also launch an immediate alarm in case of unsafe weather detected by my CloudWatcher but this is a bit of a lazy approach At the moment of this writing the GNS can be used with 4 popular session control systems CCDAutoPilo and Maxpilote support the system directly so no work is needed from your part Just take a look at next section to see any installation configuration notes CCDCommander and ACP can be used quite easily too but require you to use their scripting features please see instructions below 3 CCDAutoPilot support has just been added and tested but depending on when you read this it may have not yet made into the official release GNS 1 0 0 1 user s manual 12 Oct 23 2013 4 1 CCDAutoPilot 5 As already mentioned CCDAP v5 includes native support for the GNS thank you very much John so you ll just have to activate it from the Settings window Notifications tab 3 CCDAutoPilot Professional Sele File System Profile Targets Help Support Forum cco E AutoPilot 5 y Settings Email Settings Notify Email To C At Start of Session SMTP Server fF O O C At Start of Light Frames Phase C Authenticate C Use SSL User E At End of Session E At End of Session with Log Password
9. world This is normal since the GNS must start listening for incoming requests and you should enable unblock it in order for the system to work e Let s check if the installation went well Run a command prompt For 32 Bits systems just Start menu gt All programs gt Accessories gt Command prompt For 64 Bits systems use the 32 bit version of the command prompt browse your hard disk to the Windows sysWOW64 folder then launch the cmd program found there Goto the installation folder type cd program files gns including the quotes and followed by the return key again in 64 bit systems change to program files x86 1gns Now type update This is a test 120 followed by return GNS 1 0 0 1 user s manual 6 Oct 23 2013 Your command window should look like this EN Administrator C windows system32 cmd exe Microsoft Windows Version 6 50 6062 Copyright c 2666 Microsoft Corporation All rights reserved CowUsers jaimescd Program Files qns C 5 Program Files qns update This is a test 128 CiihProgram ee And check the GNS window did actually update to show 7 seconds later 2 Good Night System E _ gt l s Configuration Note the status message has been updated and verify it will count down to 0 secs since last poll remains at N A as the program has never been contacted by a smartphone this field will let us kn
10. 0 24 Stop 272 Watchdog timeout indicator if the white bar reachs the right side a watchdog alarm will be issued The timeout shown in the smartphone will typically be a few seconds delayed compared with the one in the PC this is normal GNS 1 0 0 1 user s manual 25 Oct 23 2013 6 Windows application options Before going on let s take a look at the few available options in the windows program Configuration options Autostartwithusersession Start minimized Local listen port 10089 Auto start with user session if checked the GNS program will be launched and will start accepting connections as soon as you log in windows May be useful if you prefer to have your smartphone connected even before the real session has started Start minimized if checked the application will be hidden in the system tray to avoid cluttering your desktop every time it is launched Of course you can make it visible again just clicking its icon in the tray Local listen port this is the slot the program will be awaiting connections from It must match the one selected in the smartphone app We chose 10099 as ports above 10000 are freely available to programs no problem in changing it if you have that port already in use but please check the available ports in your smartphone app If you change the port you ll have to restart the application for the change to
11. C Upon Weather Events Send Test Email C Upon Guide Error E Upon Plate Solve Error E On Slew Error Session rie ee aE PEN seen een eyes ESTERS TT C On Camera Error x Options C On Shutter Error A Gona Night System Focusing And that s all the GNS will be launched by CCDAP and your smartphone will track your session GNS 1 0 0 1 user s manual 13 Oct 23 2013 4 2 CCDCommander Integrating this system with CCDCommander is really straighforward as CCDC allows the user to call scripts in many cases and at any point of the action list At selected points in your action list insert a Call external subprogram action to execute the script update vbs included with your GNS distribution You ll have to call it with two parameters the first one being an informative message the second one the timeout in seconds A simple example 4 CCD Commander Session3 act alla File Edit Actions Run Setup Graphs Window Help Ol al ele x Al BOSS of ula Main Action Setup Sub Action Status Acton List Pus EA hun update vbs Session start BOL Inteligent Looe netdi Cooler Un Max Power B0 Fan On Open dome Aun list named 101805 once g Dun update vbs Session end 600 Park UAT Close dome i cton Cooler Off Fan On Cl Aun switchoth bz As can be seen in the Main Action Setup I just added two calls to Update one at the beginning of the session another when we start w
12. en extensively tested for a period of several months by a group of real users under real circumstances As you already know the Good Night System comprises two elements both needed to ensure observatory protection a a small windows program b a smartphone app It will work as shown in the following drawing CCD session control program amp Good Night System GNS 1 0 0 1 user s manual 3 Oct 23 2013 So at one side we ll have our PC GNS program being updated by our ccd session control software of choice At the other side our smartphone any number of smartphones actually will be asking the PC about the progress of the session In order to have it up and running there are a few tasks to perform to make sure everything will run fine when in real conditions We have to get the smartphone talking to the PC and then we have to get our automation program updating the PC program Let s start from the PC side GNS 1 0 0 1 user s manual 4 Oct 23 2013 2 Installing and checking the PC program Brief foreword about 32 and 64 bits systems the GNS software will run in both systems always in 32 bits mode this is not a problem as most or all astronomy software that will work with it is 32 bits In the following procedures you ll find instructions about how to test the software in both kinds of systems e Install the software it can be downloaded from the GNS page of our web site
13. http lunatico es site the software should install automatically under any current Windows version from XP to Windows 8 The only requisite is to have the NET platform already installed which is most likely the case if you are into observatory automation as it is also required by many programs and by the ASCOM platform In case you don t please visit Microsoft s NET download page http www microsoft com net download and select the platform suitable for your system GNS needs platform v 2 0 Apart from the main software itself in the installation folder c program files GNS or c program files x86 GNS the latter if yours is a 64 bit system you ll find a few scripts small programs update vbs alarm vbs switchoff vbs idle vbs message vbs These scripts will be used to integrate the GNS with some automation systems in the market other systems have or may have native support 1 If you plan to use the system with Maxpilote you ll have to select the Maxpilote folder for installation GNS 1 0 0 1 user s manual 5 Oct 23 2013 e Now run the software there s a shortcut from your start menu and you ll see the main window 2 Good Night System Lelie as Configuration FIREWALL VERY IMPORTANT AT THIS POINT if you have any kind of firewall installed it will warn you of the Good Night System program GNSUI exe trying to communicate with the outer
14. inding up and a final one to disable the system Switchoftf For each call you ll use the Run external program option from the Actions menu GNS 1 0 0 1 user s manual 14 Oct 23 2013 4 Run Program Action A Program C SProgram Files GM S4update bs E Arguments Session end 600 Program ig a f Senptle g vbs wet f Executable e q exe com bat If the message includes more than one word please enclose it in quotes as in Session end Also please note we ve selected Program is a script and unchecked not really important the optional Wait for program to finish Next in each Sub action you can add as many updates as you wish 4 CCD Commander Session3 act Fil Edit Actions Run Setup Graphs Window Help Delal elle x ale llela role a Main Action Setup Sub ction Status Name 1C1805 faces x Sub Action La EEE ESS A bhun update vbs C1805 Start 600 Ove Lo ee Focus with Clear filter Plate Sale ad Ec law auth Clear filter kaun update wbs 127605 Imaging 40011 Light 4440s Clears Ja Mther ever 1 exp Aun Once f Run until bored Run Multiple Times times C Run for a Period of Time minutes GNS 1 0 0 1 user s manual 15 Oct 23 2013 Don t forget to end the main action list calling the script switchoff vbs this one will inform your smartphone the session ended successfully and it will stop the communication Yo
15. intial Autofocus GNS 1 0 0 1 user s manual 21 Oct 23 2013 should start Util ShellExec C Program Files x86 GNS update vbs Startup 300 1 4 3 2 6 Shutdown script Here you could initiate the GNS shutdown instead of UserActions wsc File PROGRAMFILES X86 Z ACP Scheduler ShutdownObs js Util ShellExec C Program Files x86 GNS switchoff vbs 1 4 3 2 c Special Autofocus script for Scheduler If you use ACP Scheduler the AutoFocus script can be found here File PROGRAMFILES X86 Z ACP Scheduler AutoFocusScheduler vbs GNS 1 0 0 1 user s manual 22 Oct 23 2013 4 4 Maxpilote Maxpilote s author has already added native support for the Good Night System merci beaucoup Laurent gt o EE j j UU Ue Ue Shooting StartUp Watch Dome and Telescope IE _ Park telescope before Open Dome Same Crewe afina Time Open Dome Open Dome Time EMILE E About us amp Donate meore DarkBias Flat Park Telescope on End Session F Park and Close Dome on end s session eps Track Dome with scope position Siera Close MaxPilote on End Session JIES QS Manage T CCD on Start and on End While I ve been unable to test it fully I m sure any possible issues will be addressed by him the great way Maxpilote users are used to Very important for the GNS to work with Maxpilote the software must be installed in the same folder as Maxpilote
16. nloading the image Add also some time for the guider settle delay 18 Oct 23 2013 ImageStart True End Function Function ImageEnd ImageFile Util Console PrintLine useraction ImageEnd called Dim wD set wD CreateObject GNS OWL wD NewMsg Imaging finished wD NewTimeout 1 Reset imaging timeout set wD nothing ImageEnd True End Function Function Shutdown Util Console PrintLine useraction Shutdown called Dim wD set wD CreateObject GNS OWL wD NewMsg Shutdown wD NewTimeout 2 set wD nothing Shutdown False Use built in shutdown logic End Function Example screen shot after an exposure has been started Good Night System Configuration 4 3 1 6 Weather Safety script The Weather Safety Script should be changed in a way that the user will be notified if the telescope can t be parked or the dome roof not closed If everything is fine the GNS can be set to idle mode at the end of the script File PROGRAMFILES X86 ACP Obs Control ACP Weather vbs Sub Main GNS 1 0 0 1 user s manual 19 Oct 23 2013 Console PrintLine Weather Safety Script On Error Resume Next Dim wD set wD CreateObject GNS OWL wD NewMsg Weather abort wD NewTimeout 300 if Util CameraConnected then Dim FMX Console PrintLine Trying to stop FocusMax set FMX CreateObject FocusMax FocusControl FMX Halt Util WaitForMilliseconds 1000 else Console PrintLine Camera not
17. no errors but already have a list of things to add in future updates everybody is invited to contribute with ideas My apologies for the folks of the beta testing team as most of their suggestions are still there PC activate the local log so one can make a forensic analysis if something goes wrong with the session Smartphone if the session is switched off then the smartphone can be allowed to sleep a test sound button in the configuration screen offer more sounds not everybody likes the barn owl bark allow the user to set the volume in the configuration screen when the timeout reaches 0 and the alarm is fired display the last status message Add a timestamp of the last status message clear the counter when the status is set to 1 idle System General add another status message so an additional program can check for instance the weather roof status mount parked status and report it to the smartphone GNS 1 0 0 1 user s manual 28 Oct 23 2013 9 Last notes I m confident you understand there s no warranty whatsoever Use the software at your own risk If your expensive equipment gets damaged for any reason do not blame us Developing the system has taken much longer than expected for a variety of reasons but it s been worth the effort Acknowledgments Laurent Bourgon for taking the time to add support for the GNS in his Maxpilote software Gerald
18. ory router as to route incoming 10099 TCP port messages to the 10099 port of your PC if your router has a dynamic IP that is the public IP address changes from time to time and every time you power on the router then you need a dynamic host name a service provided for free by several network services such as dyndns org c your observatory is at home but in a different network than your mobile This is the same from our point of view as case b The point of all this is being able to configure your smartphone so its messages will reach the destination PC If b or c is your case please type your complete host name similar to myobservatory dyndns org in the Host filed of the smartphone configuration GNS 1 0 0 1 user s manual 11 Oct 23 2013 4 Real life integration You have surely understood the way it works now we are going to update the system with every action or groups of actions more likely the scope is going to do allotting time for them If the time expires then an alarm will be issued We can also issue an immediate alarm and of course notify the system of a successful end of the session In the simplistic example of the web site to be honest reflects the approach I m actually using and works great I just update the GNS once at the start of the session with a 10 minute timeout In this time main imaging should have been reached Once for every imaging group including
19. ow how many seconds have elapsed since the smartphone last requested an update Do not close the cmd window as we ll use it later Please forget the configuration button for the moment GNS 1 0 0 1 user s manual 7 Oct 23 2013 3 Smartphone installation Let s go now to the smartphone Enable your smartphone network connection be it wifi or mobile data 3G 4G whatever Download our Free app from Google play for Android phones or from the AppStore in case of iPhone Is is highly recommended to try with the free version first it is functionally identical to the full version with the only exception the watchdog will be disabled and will act as a countdown timer limiting the monitored session at 30 minutes This way you ll be sure everything will run smooth before spending money in the paid version Run the app and you will get to the Press Configuration to open the parameters initial screen screen Configuration ez 4 AA Port 10099 e Polling period 3 Retries 3 re ES Watchdog timeout 120 O Vibration OFF Expires end Jan 2014 c 2013 Lunatico Astronomia GNS 1 0 0 1 user s manual 8 Oct 23 2013 At this point we have to get this app communicating with our PC Please type the host name or just the IP address if you are in the same network of your observatory PC This can be a bit difficult if you know nothing about networks but having a remote or automated obse
20. rvatory you most likely know enough In case of doubt go back to your PC cmd window and type ipconfig followed by return and look for a meaningful set of 4 dot separated numbers in a line that will read something like IPv4 address see below G 5 Program Files qns gt ipconf ig Windows IP Configuration Wireless LAN adapter Wireless Network Connection Media State a Media disconnected Connection specific DNS Suffix z Ethernet adapter Local Area Connection Concraction eaacifan NAC EE 5 2 Link local IPv6 Address I feBB 18c5 4c10 6193 5123 12 IPv4 Address z 192 168 3 207 Subnet Mask a A A00 A00 200 A Default Gateway a 1192 168 3 3 192 168 3 1 Tunnel adapter Local rea Connection 3 Media State a Media disconnected Connection specific DMS Suffix Tunnel adapter Local rea Connection 4 Media State Media disconnected Connection specific DNS Suffix For the time being leave the rest of fields as they are Port is the tcp ip slot where the requests will be sent we can change this in the windows application configuration in the event the default port is already in use Polling period is the number of seconds the smartphone app will wait after an update to check again Retries means the number of times it will attempt to connect in case of any
21. u may also want to call alarm vbs in case of errors or maybe in case of unsafe weather detected note alarm is just an update with a timeout of 0 seconds CCD Commander Options amp Settings E E Mail Alerts Focuser Options DK Save Settings Load Settings Mount Parameters Auto Guide Star File Options Controll Device Plate Solve Rotator Pause Action When Weather Monitor Cancel Close Aoof Diome hen Cloud Conditions Wind Conditions Unknown Unknown w Cloudy Wl windy W Ver Cloudy ayers Windy Rain Conditions Light Conditions Rain Conditions Light Conditions e Unknown eel w Light W W vern Light Roof Dome will close autonomously M Park Mount when Pausing Action v via the Emergency Contact Closure l Before resuming action Quer Sensor every 5 minutes sensors must read good for 30 mnde Cloud Conditions Wind Conditions Monitor all these conditions for a good reading Cloud Conditions wind Conditions Rain Conditions Light Conditions Unknown Unknown w Dry Dark Light Unknown Unknown Ww Clear Calm Cloudy Mani mw Enable Weather Monitor Scripts Weather Monitor acripts After Pause C Program File GN 5 alarm wbs E After Close C Program Files GNS salarm vbs E After Good CAProgram Piles GNS alarm bz El GNS 1 0 0 1 user s manual 16 Oct 23 2013 4 3 ACP Observatory Control Software This section on integrating with ACP has been f
22. uations a your have a backyard observatory or otherwise at home that shares the same network that the smartphone You usually control your observatory PC from your living room using Windows remote desktop or similar software This is the most difficult case as your PC is probably getting it s IP address using DHCP GNS 1 0 0 1 user s manual 10 Oct 23 2013 a network protocol that assigns a different address every time you power on that is in your Windows network settings you ve leave the IP v4 address setting at the default automatic Using the ipconfig program you can find out the current IP address the 4 number set but it can change every session maybe even during an imaging sessions the address has an expiry time and this can ruin our purpose Please do assign your PC a fixed IP address I ll try to explain how to do this in future updates to this manual but for the moment please seek assistance if you don t know how to do it If this is your case set the Host field of the smartphone configuration to your 4 digit IP address b you have a remote observatory connecting to it via Internet and using a program such as teamviewer or similar In this case the settings are a bit more complex but you already know or have someone who knows In a nutshell you ll need a fixed internal network IP address in your observatory PC needed for the second step a port opened in your observat
23. ully written by Gerald Hitz great astronomer great user and above all great guy Thank you I ve only edited it to match the current document style and changed a reference to the Idle script as previously it was called calm As a plus there s also some code for our observatory control product the Firefly as Gerald marked it in green you can safely skip it if you re just interested in the GNS 4 3 1 ACP Observatory Control Software The GNS can be tightly integrated into ACP with the help of so called user actions and with extending existing scripts This short document shows an example of how to change those scripts to interact with Lunatico s GNS 4 3 1 a ACP User Actions Please refer to the ACP help how to active user actions Basically you should find a find a template file for JavaScript and also Visual Basic Script Take your favorite and create a copy named UserActions wsc After registering the UserActions wsc file to Windows with regsvr32 see ACP help especially if you run a 64bit operating system just edit this script The red lines have been added to the template green lines are some examples of how to integrate the Firefly relays and sensor box File PROGRAMFILES X86 ACP Obs Control UserActions wsc Function TargetStart Plan Target NextTarget Util Console PrintLine useraction TargetStart called Turn Mirror Fan OFF to prevent turbulences while imaging Dim FireFly set FireFly
Download Pdf Manuals
Related Search