PT578 User Manual
Contents
1. 10 FCC Notice Your KIRISUN radio generates RF electromagnetic energy during transmit mode This radio is designed WARNING for and classified as Occupational Use Only meaning it must be used only during the course of employment by individuals aware of the hazards and the ways to minimize such hazards This radio is NOT intended for use by the General Population in an uncontrolled environment This radio has been tested and complies with the FCC RF exposure limits for Occupational Use Only In addition your KIRISUN radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans FCC OET Bulletin 65 Edition 97 01 Supplement C Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromag netic Fields American National Standards Institute C95 1 1992 IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields 3 kHz to 300 Ghz American National Standards Institute C95 3 1992 IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields RF and Microwave The forementioned accessories are authorized for use with this product Use of accessories other than those listed in the instruction specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure2. KIRISUN KIIS UN ELECTRONICS SHENZHEN CO LTD 7 UNM Professional lwo way Radio 578 FM HANDHELD TRANSCEIVER INSTRUCTION MANUAL MIZUN 7220717 INSTRUCTION MANUAL PT578 FM HANDHELD TRANSCEIVER We are very grateful for your purchasing brand two way radios produced by Shenzhen Kirisun Electronics Co Ltd We believe two way radio which always incorporates the latest technology can bring great convenience to your life and work We also believe that the quality and function of lt 2 two way radio can meet your demands for reliable communication 4 Notice to the User Government laws prohibit radio communication without permission in areas dominated by the govern ment operation is subject to punishment by fine and or imprisonment Refer service to the well trained professional tech nicians only Safety Itis important that user is aware of and understands hazards common to the operation of any radios Warning Turn off your radio before entering any area with a po tentially explosive atmosphere where the air contains gas dust and smog etc such as while taking on fuel or while parking at a gasoline service station Precautions in Use Please comply with the following attentions to avoid A fire bodily injury and damage to the radio The radio is recommended to transmit for 1 mi
3. 10 FCC Notice 1 Unpacking and Checking Unpack the radio carefully We recommend that you check the radio and the supplied accessories listed in the following table before discarding the packing material If any damage loss has occurred during shipment please contact the dealer without delay Supplied Accessories Item Quantity Antenna 1 Battery 1 Belt Clip 1 Power Adapter 1 Hand Strap 1 Instruction Manual 1 Antenna Power Adapter Belt Clip Hand Strap 2 Preparation 2 1 Charging the Battery Plug the adapter into an applicable AC outlet and connect the power adapter to the battery charger The green LED will light up Place the battery or radio into the charger slot and make sure the radio has been turned off Make sure the battery is well connected with the charger Then the red LED will light up and the green LED will be out which indicates that the charging starts MMIZUN n TAEL After about 3 4 hours of charging the red LED will be out and the green LED will light up which indicates that the battery is fully charged then you can remove the battery from the charger The charger will enter the protection mode if the temperature or the circuit is abnormal and the LED will flash yellow Do not charge the battery by force at this moment just remove the battery and cut off the
4. Press the preprogrammed gramming software or send Voice Annunciation button to your ID or background sound 4 3 Select a Channel 4 5 Receive a Call Voice change the language and to your partner or the system Rotate the channel selector Release the PTT button to receive a call Press the preprogrammed knob to select the required Your dealer can set CTCSS DCS signaling on your meanwhile tne cnannel Al Off butt number can be heard g mergency ATANN channel You will hear voice i radio channels by PC software If you select a Al off t it the E Al When the preprogrammed O quie Emergency warm from the speaker while Somme channel that has been preset with the signaling you Mod 21 Talkaround button is pressed receiving valid signals will not hear other calls except those from your own system 2 Talkaround the next transmission will be at Press the preprogrammed _ the same frequency as at 6 Scan Scan button to start stop i AW which it is received scanning l CAEL Function Description Function Description If the radio stays at a noise you can receive signals that Nuisance channel while scanning press Monitor cannot be heard under normal Delete the preprogrammed Nuisance operation Press it again to temporary Dele
5. Electromagnetic Interference Compatibility During transmissions your KIRISUN radio generates RF energy that can possibly cause interference with other devices or systems To avoid such interference turn off the radio in areas where signs are posted to do so DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals aircraft and blasting sites Occupational Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the Two Way Radio EXPLICIT DEFINITIONS WORD DEFINITION Personal injury fire hazard or electric WARNING shock may occur CAUTION Equipment damage may occur If disregarded inconvenience only No NOTE risk of personal injury fire or electric shock OPERATING NOTES When transmitting with a portable radio hold the radio in a vertical position with its microphone 5 to 10 cm 2 to 4 inches away from your mouth Keep the antenna at least 2 5 cm 1 inch from your head and body If you wear a portable two way radio on your body ensure that the antenna is at least 2 5 centimeters 1 inch from
6. To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for CAUTION occupational use always adhere to the following guidelines DO NOT operate the radio without a proper antenna attached as this may damaged the radio and may also cause you to exceed FCC RF exposure limits A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio DO NOT transmits for more than 50 of total radio use time 50 duty cycle Transmitting more than 50 of the time can cause FCC RF exposure compliance requirements to be exceeded The radio is transmitting when the TX indicator lights red You can cause the radio to transmit by pressing the PTT switch ALWAYS keep the antenna at least 2 5 cm 1 inch away from the body when transmitting and only use the KIRISUN belt clip which is listed in instructions when attaching the radio to your belt etc to ensure FCC RF exposure compliance requirements are not exceeded To provide the recipients of your l CAEL n CAEL transmission the best sound quality hold the antenna at least 5 cm 2 inches from your mouth and slightly off to one side The information listed above provides the user with the information needed to make him or her aware of RF exposure and what to do to assure that this radio operates with the FCC RF exposure limits of this radio
7. master radio the cloning starts During the data transmission process the master radio will light red and the slave radio will light green When the cloning is finished the red LED of the master radio will be off and the slave radio will restart automatically 4 You can continue to clone data according to step 3 Note The wired clone function can be enabled or disabled by the PC programming software Once the wired clone function is disabled the radio cannot enter Wired Clone Mode AELA UELL 8 Troubleshooting No Problem Causes and Solutions squelch level No Problem Causes and Solutions 4 No signal D The mixer tube is broken please change it Th 4 The battery and the radio are not reliably connected Please reinstall the battery E The FM processing IC is broken please change it e radio canno 2124 The fuse of the power supply is burnt out Please change it The transmitting f be switched on or The power module is broken so there is no power output Please change it 1 The power switch is in failure Please change it 5 red light is on but display after er B The microphone is broken please change it 5 D The battery is out of power please recharge it change it no voice is heard being switched on E The CPU is broken please change it The receiving green A The channel frequen
8. the radio is forbidden to transmit after its overtime activity b During the period if the PTT button is pressed an alert tone will be sounded and the transmission is forbidden 3 TOT Pre alert a The pre alert will sound before the TOT action b After the pre alert tone the timer will action when the transmitting time has gone beyond the limit 4 TOT Reset Time a The time delay from releasing the PTT button to the resetting of the timer is limited b The countdown will go on if the time after releasing the PTT key is shorter than the reset time 6 2 Battery Saving The dealer can set the power saving mode by programming If this function is enabled and the radio hasn t receive any signal or no operation is being acted for 10 seconds the radio will enter Battery Saving Mode When a signal is received or any operation occurs it will exit the Battery Saving Mode automatically There are four types for battery saving 1 1 1 2 1 4 and Off The automatic battery saving function can reduce power consumption of the radio l CAEL MMIZON 6 3 Low Battery Warning When the battery voltage drops too low the LED will flash When the battery voltage drops too low while transmitting the LED flashes red and then the radio stops transmitting You need to recharge or change the battery 6 4 Voice Annunciation This function can be enabled or disabled by the dealer There are two languages available Chinese and
9. Do not short circuit the battery terminals or dispose battery in fire Do not disassemble the battery casing by yourself l CAEL 2 3 Installing the Antenna Hold the bottom of the antenna and turn the antenna clockwise into the connector on the top of the radio until secure 11 N A D f Speaker Microphone Open the cover for external safe speaker microphone jack and then insert the external speaker microphone plug into the jack on the radio 2 5 Installing the Belt Clip Match the two holes of the belt clip with those on the rear of the radio and then fix the belt clip to the radio with two 2 5x8 0 screws Loose the fixing screws to remove the belt clip 3 Radio Overview wa f m m LED Indicator Lights red while transmitting lights green while receiving flashes red when the radio is in low power On Off Volume Control Knob Turn clockwise until you hear a click to turn the radio power on Turn counterclockwise until you hear a click to turn it off Rotate it to adjust the volume after turning on the radio Channel Selector Knob Rotate to select channel 1 16 Antenna Top Button programmable button PTT Push To Talk Button Press and hold the PTT button and speak into the microphone
10. English After selecting a channel by turning the channel selector knob the channel number will be annunciated 6 5 CTCSS DCS The dealer can set CTCSS DCS tones on radio channels which enables you to ignore not hear calls from other irrelevant parties who are using the same channel When you receive a signal that has a tone different from the one set on your radio you will not hear the signal Likewise signals that you transmit will only be received by parties whose CTCSS DCS tones are the same as yours Note Using a CTCSS DCS channel doesn t mean your calls are private If other parties CTCSS DCS tones are identical with yours they can hear your calls Set the battery saving mode to be Off or 1 1 if the CTCSS DCS decoding time is long 6 6 Talkaround You can expand the communication range of your network through a repeater If the radio is out of the communication range you can connect with other radios through Talkaround mode Press the preprogrammed Talkaround button to switch between Talkaround mode and Repeater mode 6 7 Scan Function In order to receive calls from many different channels the radio can be programmed to scan these channels 6 7 1 Starting Stopping Scan a Press the button set as Scan to start scanning While in scanning the radio checks every channel in the scan list and stops on which a signal is detected until that signal disappears If inte
11. cy setting is out of range please reset the channel data 6 light is on but no A The speaker is broken please change it Phase lock loop The crystal oscillator of phase lock loop is broken please change it voice is heard B The audio amplifieis broken please change it 2 unlocked Beeping C The oscillating tube is broken please change it D The phase lock loop IC is broken please change it A The frequencies of both users are not the same Please select the same 9 Specifications frequency channel again 3 Cannot transmit The CTCSS DCS signals of both users are not the same Please reset it General Specification PT578 C The radio is out of effective communication range 136 17 4MHz VHF A The antenna is in poor contact Please fasten the antenna head Frequency 400 450M Z UMF 4 No signal B The HF amplifier is broken please change it 420 4 70MH2 UMF C The squelch level is so high that the squelch cannot be opened Please reset the Number of channels 16 AELA UELL General Specification PT578 Channel spacing 25kHz W 12 5kHz N Dimension HxWxD 114mmx53 5mmx33 5mm Weight 250g including battery and antenna Operating temperature 25 C 55 C Receiving sensitivity lt 0 28uV Frequency stability 2 5ppm Tx power Max frequency deviation 4W UHF 5W VHF 5KHz W 2 5KHz N Max audio power Power supply 2 1000mW DC7 4V
12. he PTT button Priority Channel Currently Working Channel When pressing the PTT button during scanning the radio will always transmit from the priority channel l AELA o CAEL When pressing the PTT button during the scanning pause the radio will transmit from the currently working channel Last Called Channel When pressing the PTT button the radio will transmit from the last channel that received a call Last Used Currently Working Channel When pressing the PTT button during the scanning the radio will transmit from the last channel that transmits signals When pressing the PTT button during the scanning pause the radio will transmit from the currently working channel 6 7 2 Nuisance Delete During scanning if a channel continually generates unwanted noise or interference you can press the preprogrammed Nuisance Delete button to remove the channel from the scan list temporarily Note The priority channel and the last channel in the scan list cannot be deleted Quit the scan mode and enter it again the deleted channel will be added to the scan list again 6 8 Lone Worker If lone worker function is enabled by PC software you can press the button set as lone worker to start lone working This mode is to ensure the safety of the user while using the radio separately The lone worker timer starts upon pressing the preprogrammed Lone Worker button If the preset lone worker time expires the rad
13. io will make an alert tone If the preset remind time expires the radio will enter Emergency Mode and make alarm In the Lone Worker Mode press the prepro grammed Lone Worker button again to quit Lone Worker Mode In the Lone Worker Mode press the prepro grammed Lone Worker Reset button if a button is designated as the lone worker timer reset button or any button if any button is designated as the lone worker timer reset button to restart the lone worker timer 6 9 Emergency Alarm Press the preprogrammed Emergency Alarm button the pressing time should be longer than the debounce time of the emergency alarm switch to enter the Emergency Alarm Mode You can give the warning tone according to the programming software or send the background sound to your partner or the system Press the preprogrammed Emergency Alarm Off button to quit the Emergency Alarm Mode the radio stops the alert and resumes normal operation 7 Wired Clone Mode If the wired clone function is enabled by PC software after entering the Wired Clone Mode the radio needs to be restart to return to user mode The operating steps go as follows 1 Press and hold side button 2 while turning the radio power on to enter Clone Mode If the wired clone function is disabled the radio will enter User Mode 2 Connect the slave radio with the master radio by a clone cable Then switch on the slave radio 3 Press side button 1 of the
14. isun Electronics Co Ltd 3 6 Building No 1 QiMin Road Song Ping Shan Area Science amp Industry Park Nanshan District Shenzhen 518057 P R China Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunication Terminal Equipment 1999 5 that any applicable Essential Test Suits measurement have been performed Description of equipment FM Handheld Transceiver Model No PT578 This compliances is based on conformity with the following harmonised standards or documents 1 ETSI EN301 489 1 2 ETSI EN301 489 5 3 ETSI EN300 086 1 4 ETSI EN300 086 2 5 EN60950 Shenzhen 10 Dec 2008 WenLiang Fu DISA SHA data General Manager vt dR Place and date of issue J 402 E1300A RD7A Signature Kirisun Electronics Co Ltd 21 22
15. nute and receive for 4 minutes Long time transmitting or con tinuous working in high power mode will make the rear side of the radio generate heat Please do not disassemble or assemble the radio un der any circumstances Please do not expose the radio to direct sunlight for a long time do not place the radio near any heating de vices either Please do not put the radio in extremely dusty moist or dabbling places do not place it on any unstable surface either Ifthe radio emits smoke or strange odors turn it off and remove the battery from the radio and contact your local authorized Kirisun dealer without delay KIRISUN ELECTRONICS SHENZHEN CO LTD N Content 1 Unpacking 2 2 2 1 Charging the 2 2 2 Installing Removing the 4 2 3 Installing the 5 2 4 Installing the External Speaker Microphone 5 2 5 Installing the 3 Radio Overview 4 Basic Operation Belt Clip visite 5 Functions of Programmable Buttons 6 Auxiliary 212 7 Wired Clone 8 Troubleshooting 9 Specifications
16. power of the charger Note The radio battery is not fully charged in the factory Before the initial use please charge the new battery KB 56B Li poly battery of the company is applicable to this radio When charging the battery for the first time after purchase or long time storage over 2 months please repeat charging several times for the battery to achieve normal capacity Meanwhile please make sure the battery is charged at least once every three months Do not recharge the battery if it has been fully charged or the radio is not in the low battery alarm state otherwise it will have bad effects on the battery s service life and performance Remove the battery from the charger after charging When the radio is in the low battery alarm state please recharge the battery before use Do not turn the radio power on by force otherwise it will have bad effects on its service life and performance 2 2 Installing Removing the Battery Installing the Battery Match the two bulges at the upper end of the battery with the corresponding grooves on the top of the radio and insert the battery Firmly press the battery pack downwards until the battery latch locks Removing the Battery To remove the battery pack push the release latch in the bottom of the radio forwards the battery will bounce up automatically Then loose the belt clip slightly and remove the battery pack away from the radio Note
17. rval between signal disappearing and continuing scanning has been preset the radio will remain on that channel b Priority Scan One channel in the scan list can be set as the priority channel which enables it to have the highest priority during scanning The radio will scan a non priority channel firstly then the priority channel and then the next non priority channel and then the priority channel again and the scan goes on like this If the priority channel and the lookback time have been set for the scan list when the radio is receiving signals on a non priority channel and the scanning is paused the radio will check the priority channel at the preset intervals If there are signals in the priority channel it will stay at the priority channel if there is no signal it will return to the original channel c The revert channel Tx channel during the scan can be designated by the dealer There are following options available Selected Channel When pressing the PTT button the radio will transmit from the first channel of the scan list Selected Channel Currently Working Channel When pressing the PTT button during scanning the radio will always transmit from the first channel in the scan list When pressing the PTT button during the scanning pause the radio will always transmit from the currently working channel Priority Channel The radio will transmit from the priority channel in the scan list when pressing t
18. te button to delete the resume normal operation noise channel temporarily Press and hold the prepro Press the preprogrammed grammed Momentary Squelch Momentary 1 High Low High Low Power Switch 11 Squelch Off Off bulon to open squelch Power button to switch between high release it to resume normal Switch and low transmitting power of operation the radio Press the preprogrammed Press and hold the prepro 12 Squelch Sduelch Off button to open grammed Momentary Monitor squelch Press it again to Momentary button to disable CTCSS DCS resume operation Monitor signaling and release the Press the preprogrammed button to resume normal Lone Worker Reset button operation 13 Lone Worker while the radio is in Lone Press the preprogrammed Reset Worker Mode to reset the lone 10 Monitor Monitor button to disable worker timer and the timer CTCSS DCS signaling and starts again 6 Auxiliary Functions 6 1 TOT Time Out Timer 1 TOT Function a The time out timer can prevent the user from continuously talking overlong and occupying one certain channel for an extended period of time and prevent the radio from heating due to continuous transmitting b The radio is set with a continuous transmitting limit If the radio is continuously transmitting longer than the time preset by the dealer the radio will make alarm and stop transmitting 2 TOT Rekey Time a A period in which
19. your body when transmitting PRECAUTIONS WARNING NEVER hold the transceiver so that the antenna is very close to or touching exposed parts of the body especially the face or eyes while transmitting The transceiver will perform best if the microphone is 5 to 10 cm 2 to 4 inches away from the lips and the transceiver is vertical WARNING NEVER operate the transceiver with a headset or other audio accessories at high volume levels CAUTION NEVER short the terminals of the battery pack NEVER connect the transceiver to a power source other than the Battery listed above Such a connection will ruin the transceiver DO NOT push the PTT when not actually desiring to transmit AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below 30 C 22 or above 60 C 140 F DO NOT modify the transceiver for any reason MAKE SURE the flexible antenna and battery pack are securely attached to the transceiver and that the antenna and battery pack are dry before attachment Exposing the inside of the transceiver to water will result in serious damage to the transceiver FCC CAUTION Changes or modifications to this device not expressly approved by KIRISUN could void your authority to operate this transceiver under FCC regulations 20 l CAELI UELL DECLARATION N N 7 20 NOTE NOTE CE 06780 We Shenzhen Kir
20. your voice can be sent to the recipient Release the PTT button to receive Side Button 1 programmable button Side Button 2 programmable button Microphone J External Speaker Microphone Jack External speaker microphone can be connected to the radio through this jack 4 Basic Operation 4 1 Switch On Switch on the radio by turning the On Off Volume control knob clockwise until a click is heard If programmed a beep tone will be heard l CAEL 4 2 Adjust Volume 5 Functions of No Programmable Buttons 4 4 Make a Call To make a call select Function Description Press the preprogrammed Squelch Off button to hear background noise Then rotate the On Off Volume Press the preprogrammed Lone Worker Lone Worker button to start stop lone working the desired channel press and hold the PTT button and speak to the The dealer can assign one of the following auxiliary functions to the top button side button 1 or side button 2 Press the preprogrammed control knob to adjust the microphone normal Emergency Alarm button to volume voice Please keep your Functi D pti unction escription mouth 5 10 away from alarm tone according the microphone None No function is assigned 4 to the setting of the pro
Download Pdf Manuals
Related Search