#29266 XP LED RC Light Kit (12pcs)
Contents
1. 29266 XP LED RC Light Kit 12pcs User Manual Thank you for your purchase of a new Team Associated LED light kit This powerful and easy to install light kit is the first choice for most model car enthusiasts The kit provides a variety of unique features and it s recommended that you read the instructions carefully prior to installation and use Improper installation may result in damage to the product Product Features e Intelligent operating system with a variety of possible applications e Led system connects to your current radio system without the use of an auxiliary channel e The system provides eight different light operating modes Normal operating mode night mode fog mode emergency mode and four different burst flash modes Product List Product Parameters e LED system control box e Operating voltage 4 8v 6 0v e Servo extension cable x 2 e Operating current 100mA e Setup operating manual e Dimensions of control box 89 x 32 x 16mm e Programming switch e LED cable Length 430mm e LED light strands e Servo extension cable length 320mm 5mm white LED x 4 e Weight 50g 5mm red LED x 2 3mm yellow LED x 4 5mm Blue LED x 2 Installation 1 Lay out the lights to the desired section of the body refer to Figure 3 Use a body reamer to make the holes for the LED light grommet be careful to not make hole too large Install Grommets into the body followed by the light into the grommet We recommend routing the2. wires so that they are clear from the antenna wire This will prevent any interference to the radio Using a piece of double sided tape mount the control box to the desired location on the body Plug Light strands into corresponding sockets on the control box refer to figure 1 There are two servo wire ports on the control box for each Channel Using one pair of the ports Ch 1 and Ch 2 Use the servo extension cables to connect your receiver to the control box You will match Ch 1 on the control box to Ch 1 on the receiver Same will go for Ch 2 refer to figure 2 8 Inthe other pair of servo wire sockets on the control box connect your Servo Ch 1 to the Ch 1 port Next connect your speed control to the Ch 2 port refer to figure 2 9 Lastly install the programming switch into the port between sockets 5 6 and 7 8 Make sure that the black wire is pointed away from the Ch 1 and Ch 2 ports N O18 W PO If the left and right turn lights are reversed simply change the side of the car that the light is on Function Control When the car is turned on all LEDs will come on for 1 second When full throttle is applied the lights will flash twice indicating that the light kit is ready for use The default setting is normal operating mode In this mode the lights will work as on a real car There are eight different light modes to choose from Normal operating mode night mode fog mode emergency m
3. ert 12 mm Sockert 2 Sockert 10 z do al 0 D c 5 a lt Sockert 1 Sockert 9 Sockert 3 Sockert 11 Sockert 5 Sockert 6 Figure 3 Light mode and the LED status xt 100 Brightness 250 Brightness Flashing e Not bright Socket7 8 Socket5 6 Forward left Conventional orward right T operating mode ft ull operation ull operation ull operation ull operation t Seekers Sockett2 Socket 6 Socker ot a e oa Oe ee Ooa a e a 3s amp Ooa Oe ee e Oo az zje oe po ee ee Oe Tl Warranty Information Your Team Associated LED light kit is warranted to the original purchaser for 30 days from the date of purchase verified by the sales receipt against defects in material and workmanship Product that has been mishandled abused used incorrectly used for an application other than intended or damaged by the user are not covered under warranty Associated Electrics Inc is not liable for any loss or damage whether direct or indirect incidental or consequential or from any special situation arising from the use misuse or abuse of this product Team Associated 26021 Commercentre Dr Lake Forest Ca 92630 Ph 949 544 7500 Fax 949 544 7501
4. ode and four different burst flash modes To change different light modes Use the Programming switch to change through the different modes Each time the button is pressed it will change to the next mode in order of how they are listed above Once the desired light mode is reached simply stop pressing the button and it will stay on that mode Remember if the car is turned off the control box defaults to the normal operating mode Schematic diagram of control box Lights line connection diagram CH4 8 L 8 L CH4 oO ial Socket 1 2 lower front light 5mm Blue CHI ee el ew eh CHI oh es i bni2 Grig A BE OR sz Socket 3 4 head light 5mm white light Se aia eee Yj REA gt ten signa Sil yellow SOCKETL SOCKET3 SOCKETS SOCKET SOCKETS SOCKET11 gare zA ISSA Socket 7 8 right turn signal 3mm yellow ps a Socket 9 10 Reversing light 5mm white Ee Socket 11 12 brake light 5mm red call S Ed IA EAA Maal al SOCKET2 SOCKET4 SOCKET6 SOCKETS SOCKET1O SOCKET12 Hesa eases J lt e PROGRAMMING SWITCH Figure 1 Figure 2 LED light installation diagram car body the same the headlights color and the color of the cable Sockert 6 Sockert 8 Sockert 4 Sock
Download Pdf Manuals
Related Search