USER MANUAL
Contents
1. MD 20879 USA We are committed to a quality product at a quality price Patton Electronics is ISO 9001 certified We meet and exceed the highest standards in the industry CE UL etc It is our business to serve you If you are not satisfied with any aspect of this product or the service provided from Patton Electronics or its distributors please let us know Thank you Burton A Patton Vice President P S Please tell us where you purchased this product2. line transients and sends them directly to chassis ground through the metal D shell Three versions of the Model 515 are available The Model 515 25 clamps at 18 volts protects all 15 pins and is designed for use with RS 232 interfaces The Model 515 6 clamps at 7 5 volts protects all 15 pins and is designed for use with RS 422 RS 423 and RS 485 interfaces The Model 515 T1 clamps at 7 5 volts protects pins 1 3 9 and 11 and is designed for use with T1 equipment All three versions provide up to 1500 Watts of transient protection Warning This product will not provide complete protection should your equipment or building be subject to a direct lightening hit 4 0 SURGE PROTECTION BENEFITS The method of surge protection used in the Model 515 adds four benefits to your system High Surge Capacity The Model 515 handles up to 1500 Watts of surge energy without failure Quick Response The Model 515 has fast response times 1 pS at the component level 0 5 uS installed Transient surges are clamped at 18V for RS 232 and 7 5V for RS 422 423 485 and 7 5V for T1 equipment Low Impedance The Model 515 adds minimal load to your system It is about the same as a gender changer Open Failure The Model 515 fails open if your system experiences a severe transient or power fault above the rated voltage of the protector This means that data and surge energy is shunted directly to chassis ground rather than being allowed to flow thr
3. on the outside of the shipping container This number may be obtained from Patton Electronics Technical Support 301 975 1007 http www patton com or support patton com Notice Packages received without an RMA number will not be accepted Patton Electronics technical staff is also available to answer any questions that might arise concerning the installation or use of your Patton Model 515 Technical Service hours are 8AM to 5PM EST Monday through Friday 1 2 CE NOTICE The CE symbol on your Patton Electronics equipment indicates that it is in compliance with the Electromagnetic Compatibility EMC directive and the Low Voltage Directive LVD of the Union European EU A Certificate of Compliance is available by contacting Technical Support 2 0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product This product has been thoroughly inspected and tested and is warranted for One Year parts and labor If any questions arise during installation or use of the unit contact Patton Electronics Technical Support 301 975 1007 http www patton com or support patton com 3 0 PRODUCT DESCRIPTION The Patton Model 515 DB 15 Surge Protector employs a solid state hybrid network to guard DB 15 data ports against data loss and hardware damage due to transient surges Equipped with one male and one female DB 15 connector the Model 515 inserts between the data cable and DB 15 port The Model 515 intercepts data
4. USER MANUAL MODEL 515 DB 15 Surge Protector PATTON Electronics To ie MODEL 515 DB 15 Surge Protector S N 123456789 PE PATTON M ElectronicsTo Part 07M515 A SALES OFFICE Doc 074220U 301 975 1000 Rev B TECHNICAL SUPPORT Revised 1 22 08 301 975 1007 http www patton com 1 0 WARRANTY Patton Electronics warrants all Model 515 components to be free from defects and will at our option repair or replace the product should it fail within one year from the first date of shipment This warranty is limited to defects in workmanship or materials and does not cover customer damage abuse or unauthorized modification If this product fails or does not perform as warranted your sole recourse shall be repair or replacement as described above Under no condition shall Patton Electronics be liable for any damages incurred by the use of this product These damages include but are not limited to the following lost profits lost savings and incidental or consequential damages arising from the use of or inability to use this product Patton Electronics specifically disclaims all other warranties expressed or implied and the installation or use of this product shall be deemed an acceptance of these terms by the user 1 1 SERVICE AND SUPPORT All warranty and nonwarranty repairs must be returned freight prepaid and insured to Patton Electronics All returns must have a Return Materials Authorization number
5. oughout the system 5 0 INSTALLATION The Patton Model 515 is simple to install and requires no user configuration Follow these installation steps 1 Disconnect the DB 15 data cable from the device you are protecting in a manner consistent with the manufacturer s installation instructions Be sure the metal D 15 connector on the device you are protecting is connected to frame ground If not contact Patton Technical Support for further instructions Plug the DB 15 connector of the Model 515 directly into the DB 15 Serial port of the device you are protecting Use of a serial cable reduces the effectiveness of the protection you would otherwise receive Re attach the DB 15 cable to the available DB 15 connector on the Model 515 The Model 515 is now inserted between the data port and the data cable and will provide up to 1500 Watts of protection to the data port Note We recommend that a Patton surge protector be connected to the other end of the data cable as well APPENDIX A PATTON MODEL 515 SPECIFICATIONS Standards Surge Capacity Connectors Compliance Pins Protected Response Time Pins Protected Response Time Pins Protected Response Time General RS 232 RS 422 423 485 T1 1500 Watts for 1mS One male and one female DB 15 CE marked for EMC directive 89 336 EEC ESD EFT Compliant with IEC 801 5 surge Model 515 25 All 15 pins on the RS 232 interface Clamped to or 18
6. volts after 0 5 US 400 Amps with a 8 20 uS pulse Model 515 6 All 15 pins on the RS 422 423 485 interface Clamped to or 7 5 volts after 0 5 uS 400 Amps with a 8 20 uS pulse Model 515 T1 Pins 1 3 9 amp 11 on the T1 interface Clamped to or 7 5 volts after 0 5 uS 400 Amps with a 8 20 uS pulse Copyright Patton Electronics Company OOOOOOAI Rights Reserved NOTES NOTES Dear Valued Customer Thank you for purchasing Patton Electronics products We do appreciate your business I trust that you find this user manual helpful We manufacture one of the widest selections of data communications products in the world including CSU DSU s network termination units powered and self powered short range modems fiber optic modems interface converters baluns electronic data switches data line surge protectors multiplexers transceivers hubs print servers and much more We produce these products at our Gaithersburg MD USA facility and can custom manufacture products for your unique needs We would like to hear from you Please contact us in any of the following ways to tell us how you like this product and how we can meet your product needs today and in the future Web http www patton com Sales E mail sales patton com Support E mail support patton com Phone Sales 301 975 1000 Phone Support 301 975 1007 Fax 301 869 9293 Mail Patton Electronics Company 7622 Rickenbacker Drive Gaithersburg
Download Pdf Manuals
Related Search