SuperConductor User Manual
Contents
1. If the level is the level you want Proceed with recording process Set the desired record level now Do not overdrive the Rec inputs e When your recording is through click Stop Actions e Your audio recording has been assigned an alpha numeric file name i e 060606F4 and is assigned to knob 41 e To rename this file you must go to the Knob Set page and save position 41 to not selected LCM To record audio via the LCM CHAPTER 7 RECORDING AUDIO e From the Main Menu turn the knob until the LCD reads KNOB SET RECORD Press the knob to select Once selected the top line will read Select Knob Pos This is because the first step to recording audio via the LCM is to select the knob position to which to assign it Tum the knob until you find an open slot and press the knob to select it Note if you select a knob position that currently has a file assigned to it you will overwrite the position but the file will remain on the unit When you select a knob position the top line of the LCD will change to Editing knob position You can then perform two actions by turning the knob EuXLO ae Assign Audio Record Audio e Select the record audio option and press the knob e The top line of the LCD will now read knob position Record Sound The bottom line of the LCD will inform you that any existing sound attached to the knob position you have selected will simply be mo2. Technomad Audio Anywhere SuperConductor User Manual How to work with the Technomad SuperConductor This document and its contents are furnished as is for informational purposes only and are subject to change without notice Technomad does not represent or warrant that any product or business plans expressed or implied will be fulfilled in any way Any actions taken by the user of this document in response to the document or its contents will be solely at the risk of the user TECHNOMAD MAKES NO WARRANTIES EXPRESSED OR IMPLIED WITH RESPECT TO THIS DOCUMENT OR ITS CONTENTS AND HEREBY EXPRESSLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR USE OR NON INFRINGEMENT IN NO EVENT SHALL TECHNOMAD BE HELD LIABLE FOR ANY DIRECT INDIRECT SPECIAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THE USE OF ANY PORTION OF THE INFORMATION Copyright 2008 by Technomad All rights reserved This document may not be reproduced photocopied displayed transmitted or otherwise copied in whole or in part in any form or by any means now known or later developed such as electronic optical or mechanical means without the written agreement of Technomad Any unauthorized use may be a violation of domestic or international law Technomad and the Technomad logo are trademarks of Technomad All other product or company names mentioned are used for identification purposes only and may be t
3. LOOP LOOP not set not set not set not set not set not set not set T 7 not set na not set a mez not set na ale not set le len le len len 2 len ls len len lr To clear a knob position e Click the Trash Can Icon next to the knob position you want to clear Note the file will not be deleted CHAPTER 7 RECORDING AUDIO Scheduling In addition to the remote control and knob based playback of audio files the SuperConductor also supports scheduled playback through the Schedule Manager via the web interface and LCM Web Interface Managing the schedule which includes adding and deleting schedule tasks via the web interface is handled through the Scheduler Tab eoo Technomad SuperConductor Scheduled tasks e gt ecx GA rf qIOPUTETTETIEUOUSEOOU pp T A Br COL hup 1 82 48 141 191 schedule html wy I AN CCl Google Q Technomad SUPERCONDUCTOR SETTINGS military audio systems SCHEDULER a D repeated Repeat defines how many times the MP3 file will be played in single task lc Click on button SET TASK to set your selection tempor Scheduled tasks overview E File Day Date Time Until Every Repeat Action BU_MAIL DAILY 10 01 1 off Cea Cael Inactive tasks will be shown with a gray background If you click the edit button the task assignment form will be
4. e Subnet 255 255 255 0 Configuring the SuperConductor In order to configure the SuperConductor you must first enable it to connect to your network This can be done either through the LCM or Web interface The LCM e First set the unit into local configuration mode LCM by turning the knob one turn past the last music assignment until the above message appears e Press the knob until Configuration becomes Entering Local Configuration Mode approximately 5 seconds e Upon first entering the LCM you will be required to specify your password The unit comes pre configured with a default password of 0000 CHAPTER 3 SETUP AND CONFIGURATION Timing e In authentication mode the top line of the LCD will read Password and the bottom will read with the first blinking e To set the password turn the dial for each until the appropriate digit is displayed Press the knob to advance to the next digit When finished press the knob again Upon successful authentication the LCD will display Main Menu There are three elements to connecting your SuperConductor to your network e P address e Subnet and e Router Before using the LCM to modify the unit it is important to understand the timing required for employing the knob in order to prevent the unit from locking up The timing example below demonstrates setting a new schedule item Note the wait points within the ins
5. EE E E E E E R To set a knob position e First enter a knob position in the Knob Text Field Note if you select a knob position that is already filled the new file will replace the existing file for that position the file will not be deleted e Next select the file you want to assign to that position by using the File Drop down e Then select the playback mode for the knob position using the Mode Drop down Options include o Once o Loop and o Push the file will play as long as the knob is pressed in e Finally click the Set Button to set the knob position e When you have made all the changes you wish to make to knob positions click the Save Button to confirm the changes to the unit CHAPTER 7 RECORDING AUDIO LCM To assign an audio file to a knob position via the LCM e From the Main Menu turn the knob until the LCD reads KNOB SET RECORD e Press the knob to select Once selected the top line will read Select Knob Pos This is because the first step to recording audio via the LCM is to select the knob position to which to assign it Tum the knob until you find an open slot and press the knob to select it Note if you select a knob position that currently has a file assigned to it you will overwrite the position but the file will remain on the unit e When you select a knob position the top line of the LCD will change to Editing knob position You can
6. list via the LCM e Select the UP Option from the modification menu of the scheduled task you selected e When the option is selected the upper LCD line reads Schedule Line XX and the bottom provides two options o Move Up and o Exit e To move the scheduled task up 1 place in the scheduled task list push the knob when the Move Up option is blinking if it s not blinking use the knob to scroll until it is e Upon selecting the option you will be returned to the item menu Note if you wish to move the scheduled task down further you must repeat this process Adding a Scheduled Item To add a new scheduled task from the LCM e From the Main Menu tum the knob until the LCD reads SCHEDULE e Press the knob to select Once selected the top line will read Schedule The bottom line displays Scroll down to view edit e To find a scheduled task turn the knob to scroll through the scheduled tasks Each one will display horizontally scrolling as CHAPTER 7 RECORDING AUDIO o HEFILENAME Day datefield Time timefield Until untilfield Every everyfield Repeat repeatfield e To enter the modification mode push the knob when the scheduled task you want to modify is displayed e The modification mode includes six options that can be scrolled through with the knob o EDIT o DEL o OFF ON o DOWN o UP o EXIT e Toadd the new item scroll once past the last menu item Exit This will display an
7. of this manual O SET PASSWORD TIME DATE LIBRARY KNOB SET RECORD IP ADDRESS SUBNET ROUTER IP REMOTE CONTROL CHAPTER 4 INTERFACE o LOCKOUT o SCHEDULE o EXIT e Upon successfully logging in to the LCM you can navigate through the menu options listed above by tuming the knob e To dive into a menu option simply press the knob For more information about logging into the LCM see the Logging in section of this manual To exit the LCM mode and save any changes you have made browse to the EXIT top level menu and press the knob This will commit your changes to the unit s non volatile memory and reboot the unit for the changes to take effect See Appendix B for a one page quick access guide to operating the LCM CHAPTER 4 INTERFACE Web Control Panel eoo Technomad SuperConductor Status page lt gt XIA H http 192 168 0 99 index html wy M Clg Google Q Technomad SUPERCONDUCTOR SETTINGS military audio systems Status display Current Time 10 14 08 14 50 Advertisement Visit Technomad s website by clicking on the pa 75 Technomad logo above Status Inactive Timeserver Disabled Current refresh rate 2 seconds Set refresh rate to 2 seconds 5 seconds 10 seconds The Web Control Panel is divided into six main tabs e Status e Settings e Control e MP3 Upload e Knob Set and e Scheduler To access the feature simply clic
8. positions can be set and deleted The knob positions can be set via the web interface and the LCM Knob positions are set in the web interface from the Knob Set Tab CHAPTER 7 RECORDING AUDIO eoo Technomad SuperConductor Knob set e OD OOO EOL CI Technomad SUPERCONDUCTOR SETTINGS military audio SUS te ms m W 55 Knob assignment overview the file over and over on a button push a Knob File Mode File Knob File second push stops it PUSH plays the BU ADJUT SR WEATH notset na file over and over as long as a button is s not set a SR_AIRRD BU_REVEI BU_OFFIC not set na a l not set SR_ALERT LOOP Bu_sick ONCE BU_QUART ONCE BU GUARD ONCE BU ASSMB ONCE E SO ARMY LOOP al 3l FX_EXPL3 LOOP na mi 38 notset na mi FX BOMB LOOP mul na Knob assignment overview Shows the current assignment of all 64 knob positions FX_EXPL2 Click the trashcan icon to clear a particular knob assignment You will be PX_BOCAL prompted to confirm this action na notset na m not set na not set na iil not set na al not set na not set notset na na sS notset na not set na ors na mi 58 not set na E not set na m 60 not set na na me not set na ai not set na m not set na mj notset na not set na EEE EEE
9. preset Delete all tasks with the definitions of this particular task You can then easily change CHAPTER 7 RECORDING AUDIO The Scheduler tab is broken into two primary areas Creating a scheduled task and Managing existing tasks Ascheduled task represents the playback of an audio file according to specific parameters such as day time to play file to play and how to play it For each scheduled task you can specify the following through the Scheduled Task Assignment Table Insert each task can be scheduled in relation to other tasks Select where the new task should be inserted o Before o After or o Replace an existing task Task set the task number that applies to the order of insertion Status use the Status Drop down to set the task to either Active or Inactive File use the drop down to select the file to which the task applies Date Day select a specific date using the date drop downs or a day for every week playback Frequency using the At until Every and Repeat fields you can specify the frequency of the task o At select the time at which to start the playback of the select audio file o Until select a time at which to stop the playback o Every set a number of minutes at which to repeat the file o Repeat set a number of times the file should repeat To save the task immediately click the Set Task Button This will store the task in memory To permanently save the task to the
10. selecting delete you will be returned to the item menu Turning a Scheduled Task On Off To turn a scheduled task on or off via the LCM e Select the OFF ON Option from the modification menu of the scheduled task you selected Note the actual name of the item On or OfP depends upon the current state of the selected scheduled task e When the option is selected the upper LCD line reads Schedule Line XX and the bottom provides two options o Tum Off or Turn On and o Ext e To change the state of the scheduled item push the knob when the Turn Off or Turn On option is blinking if it s not blinking use the knob to scroll until it is e Upon selecting the option you will be returned to the item menu Moving a Scheduled Task To move a scheduled task down in the task list via the LCM e Select the DOWN Option from the modification menu of the scheduled task you selected e When the option is selected the upper LCD line reads Schedule Line XX and the bottom provides two options o Move Down and o Ext e To move the scheduled task down 1 place in the scheduled task list push the knob when the Move Down option is blinking if it s not blinking use the knob to scroll until it is CHAPTER 7 RECORDING AUDIO e Upon selecting the option you will be returned to the item menu Note if you wish to move the scheduled task down further you must repeat this process To move a scheduled task up in the task
11. unit s non volatile flash memory click the Save Button CHAPTER 7 RECORDING AUDIO Note Remember It is important to know how long a file playing is If the playing time runs into the next task the lower priority task will not play Managing Existing Tasks Existing scheduled tasks are located in the table at the bottom of the Scheduler tab For each scheduled task you can e Tum it off e Editit e Delete it Turn Off a Task To turn off a task click the Off Button in the Action Column of the scheduled tasks table Edit a Task To edit an existing task click the Edit Button in the Action Column of the scheduled tasks table This will load the task detail into the Scheduled Task Assignment Fields for editing When you have made your changes click the Save Button to confirm them into the units storage memory Delete a Task To delete a task click the Del Button in the Action Column of the scheduled tasks table Alternatively you can click the Delete All Tasks Button to remove all scheduled tasks LCM You can manage the schedule which includes editing and deleting schedule tasks as well as add new schedule items via the LCM e From the Main Menu tum the knob until the LCD reads SCHEDULE e Press the knob to select Once selected the top line will read Schedule The bottom line displays Scroll down to view edit CHAPTER 7 RECORDING AUDIO e To find a scheduled task turn the k
12. 08 RC 38 L control html o PARAMETERS C 3 start recording function CHAPTER 11 PLAYING SOUNDS KREC is a free knob position Stop Recording o COMMAND http 192 168 0 30 BAS cgi KREC 08L control html o PARAMETERS None APPENDIX B LCM QUICK ACCESS LCM Function Configuration Mode Play a Sound Reset Device in the event that the firmware is update or the device freezes Scroll past last knob setting Push and hold control knob until password displays Enter password by turning knob at each star until correct digit displays and then pressing the knob Cycle knob through sounds Press knob to play selected sound depress the reset button all the way for one second
13. 1 A O O esa eee ets 22 Web Based Control Paladar 22 Pea ie ee E ca ae E tae as 25 Technomad SuperConductor User s Manual Page i of 65 Remote Contlol ctio ecce a 32 Enabling the Remote CONTO aiii 32 Web ido 32 gel a eae Dur aes crea en uo Lat atte cee 34 WED Interface facili at E LA a 34 I ae Ne dte ce sk ec EN M Dp NM I E 35 Managing ss ac euer 37 Requiem sia iia 37 UA e NN EIS 37 Renaming Res e at e td e tent 38 Vedan cm E 39 Deleting Fue me o 40 WD Hle OO nan tae 40 Ens ed un eT mem 42 Setting Knob PoSIOTIS 2 5 nectit eit rs cet eerie ala accel ST ea a sut 42 MR A E A 42 Rb MET 44 Clearing Krob PESIHOLS ceti tote Deep Dust te ore teta 45 Web nice PEE 45 vie mc etkcuca teers atslactanraniaula nates lideca a aeemense leaden 46 Web Interface fecal pas sk A ol orta dba be A e buo nd udi 46 Creating a Scheduled Task e 4T Managing Existing TASKS pucca de rer trit adt hip d cem duet 48 Boy P OE 48 Editing a Scheduled Task nnn tenes 49 Delete a Scheduled asc cep oia paie cad 51 Turning a Scheduled Task OO ati i a coi torri 52 Moving a Scheduled Task a tor ee des 52 Adding a Scheduled Ims de Grades dan t ipee o pr bores 53 Playing SONS ata c P 55 Via Remote COTO aci ll 55 A m 55 Via COl Command T UN 55 Securitas A aaa 56 E dedo Robledo ap e bea e ta n cie 56 LGM rr CE 56 Appendix A CGI GOMM ANAS laca 57 A raeh earan a R aani oid rese rra anai 5
14. 5 port on the front of the unit provides connectivity to a standard network e Serial Port available through hatch Back panel e Line Out two standard 1 x 1 4 TRS stereo speaker connections to connect to your sound system e Line In one standard 1 x 74 TRS stereo connection for microphone connection and audio recording e Power the table below provides information about the SuperConductor power requirements Item output output working watts current mA current mA AC P P RMS V DC Technomad SuperConductor User s Guide Page 6 of 65 CHAPTER 1 ABOUT SUPERCONDUCTOR Superconductor in chassis w CD not on use fhs 130 Superconductor 2 7vac max 12vdc 250 100 Ovrms playing song MP3 measured with Watts up measure p p and RMS siren wail output 10096 kkk output set to 70 matches CD player The SuperConductor s primary interface is through the LCD panel This LCD panel displays all information accessible through the control Upon system start and idle the LCD panel displays the IP address assigned to the unit To startup the SuperConductor flick the power switch upwards Technomad SuperConductor User s Guide Page 7 of 65 CHAPTER 3 SETUP AND CONFIGURATION Setup and Configuration Prior to using the SuperConductor you must connect it to your network so that it can be easily controlled via the web based interface The unit comes standard with the following IP configuration e P 192 168 12
15. 7 Syta A EE TEX 58 Appendix B Quick LCM ACCESS et det b ande traer 61 Technomad SuperConductor User s Manual Page ii of 65 CHAPTER 1 ABOUT SUPERCONDUCTOR The SuperConductor is a 1U rack mountable automatic MP3 player recorder with internal clock and is ideal for themed entertainment airport announcements SFX sports facilities and more The TCP IP based SuperConductor provides 1500 minutes of internal storage is upgradable via firmware flashing and is completely configurable through a web based interface or an LCD front panel The Technomad SuperConductor has a number of valuable benefits Networkable the SuperConductor is easily networked so that it can be configured and controlled remotely including audio playback Schedulable the SuperConductor can be schedule to play music at a certain time or a certain interval i e every 30 minutes A robust internal Real Time Clock RTC or internet Time Server ensures accurate time Audio Line in the SuperConductor includes stereo line in jacks that encodes recorded audio as high quality 192kbps MP3 sound files Multi assignments through the web interface or front panel music files stored on the SuperConductor can be assigned to one or more knob positions Integration the SuperConductor integrates with your existing audio systems i e internal building audio systems using standard line level cables or order it with any Technomad Turnkey PA System This ma
16. Add option Press the knob to select this option e When the Add option is selected the upper LCD line will display Add Line to Schedule and the lower line will display Click to add or scroll on top to exit e Push the knob button to create a new scheduled task one number higher than the highest schedule number So if the last scheduled task is number 15 this will create number 16 Note this makes the new task the lowest in priority e Creating the details of the new scheduled task is identical to editing an existing task For more information read the appropriate section on editing a task through the LCM CHAPTER 11 PLAYING SOUNDS The SuperConductor has two output connections left and right on the back panel for stereo output to your sound system Audio files loaded onto the SuperConductor can be played back in a number of ways e Via remote control through the web interface e V a the knob on the unit and e Via CGI network command Playback of audio files by remote control through the web interface is explained in the Remote Control chapter To playback audio files using the knob on the SuperConductor unit e From the unit turn the knob until you find the file you wish to play and press the knob This will display on the top line of the LCD When you press the knob the file will immediately begin to play e Youcan then also assign a follow up file to play via the second line of the LCD following
17. LOAD Set Password SCHEDULER Volume Choose the playback volume from 0 to 100 in 5 steps IP Address Enter the 4 values of the desired device IP address e g 192 168 1 2 Netmask Enter the 4 values of the desired Static IP e g 255 255 255 0 Router IP Address Enter the 4 values of the desired Router IP address e g 192 168 1 1 Apply To store the changes click on Apply The device will restart with the new setting Cancel To discard the changes click on Cancel System date Displays the current system date and time Set clock Use Date to set the system date in the format mm dd yy Use Time to set the system time in the format hh mm Set time Click the Set time button to store the new system time and date The device will restart with the new settings Timeserver IP Enter the 4 values of the desired Timeserver IP Time Shift Set Time Shift with the time server to your location Example HH 10 MM 20 will substract 10h and 20min to the NTP server time HH 10 MM 20 will add 10h and 20min to the NTP server time Timeserver State Set Timeserver syncronization mode On or Off Update Timeserver Apply Timeserver section changes Set Old New Password Set the new system password for the WEB LCM setting access Password must be 4 characters length If no password is set a single Set Password field is visible otherwise the old password must be specified CHAPTER 4 I
18. NTERFACE The Settings tab provides access to a number of SuperConductor configuration settings including e Volume e Network e Date Time and e Password Volume Use the drop down menu to select the volume level in increments of 5 Network You can specify the following e P Address the IP Address of the unit e Netmask the Subnet address of the unit e Router IP address the IP address of the router to be used by the unit this is for remote control and time server connectivity If you don t have critical network information available i e subnet mask and routerlP gateway you can obtain that information from the computer on which you are working e Open a command prompt on your computer e When the command prompt opens enter configip all and press the Enter Key CHAPTER 4 INTERFACE er gt ipconfig all VOUR 1731D36CF5 Hybrid kt No No Zi IntelCR PROZ 1888 CT Network Connect G 11 11 n N8 1B 125 2008 8 44 45 AM pri 2AAR 2 44 45 AM ASAS f word documents TECHNOMAD WARNI x Command Pronpt BO FQ 052 Jo ES aam e This will display a list of IP addresses associated with each of the network connections on your computer From this output you can get the following address required to configure the SuperConductor o Subnet Mask Netmask o Default Gateway RouterlP Address Date and Time There are two methods by which to specify the date and time e Manual or e Time S
19. RJ45 Ethernet jack Audio input 1 x TRS stereo unbalanced RCA standard other connector types available by special order Audio output 1 x TRS stereo unbalanced RCA standard other connector types available by special order Mounting Rackmount 19 standard Local Control Mode LCM The SuperConductor includes a Local Control Mode that allows complete control and manipulation of the units features without having to interact with it via the web based interface To access the LCM e Scroll to the last knob position with a sound assigned to it If all positions are filled the last knob position will be 99 Technomad SuperConductor User s Guide Page 5 of 65 CHAPTER 1 ABOUT SUPERCONDUCTOR e Once the last position is reached turn the knob clockwise one additional time This will display the LCM entry screen Note when the LCM entry screen displays it will indicate the process for committing changes via the LCM to the SuperConductor unit After changes are made using the LCM reset the device to set the changes Controls The SuperConductor unit has two primary controls e Knob the knob turns clockwise and counterclockwise to navigate through functionality and assigned music It also presses inward to commit selections and changes e Power Switch the power switch turns the unit on and off Ports and Inputs The SuperConductor unit has the following ports Front Panel e RJ45 the RJ4
20. Timeserver State Set Timeserver syncronization mode On or Off the old password must be specified The configuration of the SuperConductor s network settings is specified in three fields IP Address Netmask or Subnet and Router IP Address For each of the specific fields simply enter the appropriate IP address as per your network requirements and click the Reboot Device Button This will reboot the SuperConductor with the new network settings At this time you should reset your computer s original network information and connect the SuperConductor to a switch or hub managed by your network Once the SuperConductor is properly situated in your network open the web browser on any PC connected to your network and browse to the IP address you specified above CHAPTER 3 SETUP AND CONFIGURATION Logging In Authentication is required for modifying SuperConductor settings either through the LCM or Web based interface LCM Login To login through the LCM e First set the unit into local configuration mode LCM by turning the knob one turn past the last music assignment In a new unit you shouldn t have any assigned slots e Press the knob for 5 seconds as indicated on the LCD e Upon first entering the LCM you will be required to specify your password The unit comes pre configured with a default password of 0000 e In authentication mode the top line of the LCD will read Password and the bottom wil
21. URL of your Superconductor unit For example http 192 168 1 5 e CGI Application the name of the CGI application BAS cgi e fc command e file name optional e command Below are some examples of CGI commands and an explanation of the actions they perform Note this examples utilize an IP address of 192 168 0 30 For correct operation with your SuperConductor unit you must replace this IP address with the actual IP address of your unit e Play a Knob Sound o COMMAND http 192 168 0 30 BAS cgi rc 1 amp sound 1 amp plmod ONE PARAMETERS C 1 play knob sound function CHAPTER 11 PLAYING SOUNDS Sound knob position to play 1 2 to 99 plmod play mode ONE or LOO e Playa file o COMMAND http 192 168 0 30 BAS cgi ro 2 amp name NINETEEN amp plmod ONE PARAMETERS 1c 2 play a file function name file name to play 1 2 to 99 plmod play mode ONE or LOO e Stop Playing o COMMAND http 192 168 0 30 BAS cgi rc 18sound 0 o COMMAND http 192 168 0 30 BAS cgi rc 2 amp name o PARAMETERS None e Knob Lockout o COMMAND http 192 168 0 30 setup cgi L reboot html amp B524 1 o COMMAND http 192 168 0 30 setup cgi L reboot html amp B524 1 PARAMETERS e B524 1 set knob lockout on e B524 0 set knob lockout off Note this command stores the setting in the non volatile memory and causes a device reset Start Recording o COMMAND http 192 168 0 30 BAS cgi KREC
22. an be deleted from both the web interface and the LCM Web Interface Audio files can be deleted through the MP3 Upload tab in the web interface CHAPTER 7 RECORDING AUDIO http 82 48 141 191 upload html A Y J E SUPERCONDUCTOR SETTINGS military audio systems conor i il ll e w w P z BABSIS mi WALK mi gg 2 E w w heh z o ak E i Rjal E To delete a file e Click the Trashcan Icon next to the file you wish to remove from the file list on the MP3 UPLOAD page Note files can only be deleted from the USB storage via the MP3 UPLOAD page when they are not in use Ifa file is in use you will need to remove it from its knob position To remove a file from it s Knob position you may click the trashcan on the knob setting line or enter the knob setting number in the knob setting field at the top of the page and choose not selected then set and save or remove it from the scheduler If it is a scheduled task click the del button in the action section of the schedule For more information about configuring files to knob positions see the Knob Management chapter in this manual CHAPTER 7 RECORDING AUDIO The knob is the primary method by which audio is played on the unit By assigning a file to a knob position from 1 to 99 the audio file can be easily played from the unit simply by turning the knob to that position and pressing Through the web interface and LCM knob
23. as indicated on the LCD e Upon first entering the LCM you will be required to specify your password The unit comes pre configured with a default password of 0000 e In authentication mode the top line of the LCD will read Password and the bottom will read XXXX with the first X blinking e To enter the password turn the dial for each X until the appropriate digit is displayed Press the knob to advance to the next digit When finished press the knob again Upon successful authentication the LCD will display Main Menu Appendix Appendix A CGl Commands The CGI Command feature allows you to remotely control playback by sending commands through the Common Gateway Interface CGI The SuperConductor includes a small light weight web server that receives commands through Port 80 Parameters The following table provides an overview of some of the available CGI parameters CHAPTER 11 PLAYING SOUNDS rc Numerical command issued to unit 1 2 3 to begin action name The name of the file without NA extension The play mode for the file ONE play once LOOP play continuously Starting and stopping playback O stop playback 1 start playback B524 Knob lockout 0 lockout 1 not lockout KREC Knob position Number associated with a free knob position for recording L Name of page that initiates i e control html command to unit The following is the syntax for all CGI commands e Location the
24. e Upon successful authentication you can navigate through the interface e To set the IP address click the Settings Tab This will display the SuperConductor Settings screen CHAPTER 3 SETUP AND CONFIGURATION eoe XA ADO O http 192 168 0 99 settings html wy M Technomad SuperConductor Settings Technomad SUPERCONDUCTOR SETTINGS military audio systems Volume Choose the playback volume from 0 to 100 in 5 steps IP Address Enter the 4 values of the desired device IP address e g 192 168 1 2 Netmask Enter the 4 values of the desired Static IP e g 255 255 255 0 Router IP Address Enter the 4 values of the desired Router IP address e g 192 168 1 1 Apply To store the changes click on Apply The device will restart with the new setting Cancel To discard the changes click on Cancel System date Displays the current system date and time Set clock Use Date to set the system date in the format mm dd yy Use Time to set the system time in the format hh mm Set time Click the Set time button to store the new system time and date The device will restart with the new settings Timeserver IP Enter the 4 values of the desired Timeserver IP Time Shift Set Time Shift with the time server to your location Example HH 10 MM 20 will substract 10h and 20min to the NTP server time HH 10 MM 20 will add 10h and 20min to the NTP server time
25. either turn the feature on or off depending upon what is currently selected The LCM will automatically save the settings and return you to the TimeServer menu P address e When blinking press the knob to display an IP Address entry screen o The top line of the LCD will read Set Timeserver and the bottom line will display an IP address masking in the format of XXX XXX XXX XXX with the first X of the first set blinking CHAPTER 4 INTERFACE o To set each digit of the timeserver address turn the dial for each X until the appropriate digit is displayed 0 9 Press the knob to advance to the next digit o When all digits are set the top line of the LCD will display Timeserver Address Set to then Click to Continue Offset e When blinking press the knob to display an entry mechanism for an hour and minute offset from the timeserver e The top line of the LCD will read Enter the time offset from the timeserver to your location e The bottom of the LCD will flash the Set command and the Timeserver command Use the knob to select either the Set option for manual or the TimeServer option to specify timeserver settings Password To specify a new password e From the Main Menu turn the knob until the LCD reads SET PASSWORD e Press the knob to select This will enter the Password Set feature e The top line of the LCD will read Set Pas
26. elect this option the upper LCD line will display Choose Every Interval and the lower LCD line will display MMM with the first M blinking Use the knob to scroll through the digits until you find the correct one representing the number of minutes you wish for the scheduled task to work Push the knob in to select Repeat for each digit When you have finished you will be returned to the main item menu for the scheduled task o Repeat when you select this option the upper LCD line will display Choose Repeat and the lower LCD line will display with the first blinking Use the knob to scroll through the digits until you find the correct one representing the number of times you wish the scheduled task to repeat within the time frame specified Push the knob in to select Repeat for each digit When you have finished you will be returned to the main item menu for the scheduled task o Exit save settings and return to the list of scheduled tasks Delete a Scheduled Task To delete a scheduled task via the LCM e Select the DEL Option from the modification menu of the scheduled task you selected e When the DEL option is selected the upper LCD line reads Schedule Line XX and the bottom provides two options o Delete and o Ext e To delete the scheduled item push the knob when the delete option is blinking if it s not blinking use the knob to scroll until it is CHAPTER 7 RECORDING AUDIO e Upon
27. erver To specify the date time manually e Date enter the month day and year in the appropriate text fields e Time use the drop down menus to select the hours and minutes Note once set the unit will increment the date and time using ts internal clock To specify the date time using the time server e Timeserver IP enter the IP address of the timeserver CHAPTER 4 INTERFACE Password IP Address e Time shift using the drop down select the hours and minutes of shift between your timezone and the timeserver For example if the time server is in London and you are in California the hour shift would be 8 e Timeserver State use the drop down to select to have the unit synchronize automatically with the time server e When finished click the Update Timeserver Button to commit the changes Note before changing the timeserver IP it is a good idea to make sure that your SuperConductor has a valid IP address and gateway If it does not it won t be able to find the IP address of the timeserver you are specifying To change the password e Enter the old password first then e Enter the new password e Click the Set Password button to commit the changes Note password must be 4 digits in length Numbers only Through the LCM you can modify the following settings e Network e Date e Time and e Password Note this section assumes that you have already logged into the LCM For more information about l
28. he Upload Button to upload the file to the unit When the file has been successfully uploaded it will be listed at the bottom of the file list Renaming Files Audio files can be renamed through the MP3 Upload tab in the web interface as well as the LCM CHAPTER 7 RECORDING AUDIO Web Interface Technomad SuperConductor MP3 upload 4 Techn STATUS e select USB file listing 09 BU_RECAL BU_ADJUT BU_ASSMB BABSIS O9WALK BU_FIRST BU_GUARD 3 in use in use a in use in use BU MAIL in use BU OFFIC BU QUART in use in use BU REVEI in use BU SICK CHAM CHA FX 50CAL FX BOMB FX CAN30 FX EXPL1 in use ml in use in use bi LCM http 82 48 141 191 upload html WY Gla Google Q Omad SUPERCONDUCTOR SETTINGS CONTROL MP3 UPLOAD Upload Click on the Browse button to select the MP3 file Once selected click on the Upload button to start the upload Up to 128 files can be uploaded Browse Upload Rename USB file listing Shows all MP3 files uploaded to the USB stick Click the trashcan icon to delete an MP3 file from the USB stick You will be prompted to confirm the deletion of an MP3 file NOTE You can only delete MP3 files that have no knob assignment and are not used in a scheduled task Rename file Rename a library file it must be not used in any knob position o
29. he upper LCD line and lower LCD line that you have assigned the scheduled task to the specific day selected You will then be presented with an option to select the date The lower LCD line will display MM DD YY with the first M blinking Use the knob to scroll through the digits until you find the correct one representing the date you wish for the scheduled task Push the knob in to select Repeat for each digit When you have finished you will be returned to the main item menu for the scheduled task Time when you select this option the upper LCD line will display Choose Start Time and the lower LCD line will display HH MM with the first H blinking Use the knob to scroll through the digits until you find the correct one representing the time you wish for the scheduled task to start Push the knob in to select Repeat for each digit When you have finished you will be returned to the main item menu for the scheduled task Until when you select this option the upper LCD line will display Choose Until Time and the lower LCD line will display HH MM with the first H blinking Use the knob to scroll through the digits until you find the correct one representing the time you wish for the scheduled task to work until Push the knob in to select Repeat for each digit When you have finished you will be returned to the main item menu for the scheduled task CHAPTER 7 RECORDING AUDIO o Every when you s
30. ied out through the Control Tab CHAPTER 7 RECORDING AUDIO eoo Technomad SuperConductor Control lt gt Ce Cx A B CL hip 82 48 141 191 control htm v v M Google q Technomad SUPERCONDUCTOR SETTINGS military a audio systems wr 6 5 gb hc um wr L8 Lk ee wr LEA S Remote Control Remote Control show the state of the remote control if enabled is possible to Remote Control enabled control the device by the commands available on this page Knob Lockout Knob Lockout enable or disable the knob play command functionality Play Sound Play Sound play section Play knob position select a knob position to play mame Se SGD Meyteseutemonretonthay Record Sound Record Sound record section Recording status stop Knot poakiore so eck a kha positon Actions click on Rec and Stop commands to respectively start and stop the Knob position select F recording process Actions NOTE The new sound will be named XX mp3 where XX is the selected knob position The sound will be automatically assigned to the XX position e Scroll to Recording Status on Control page e Select unused knob position i e 41 Knob Position e Set record level Click on Rec Action and send an audio signal to the stereo Line Rec inputs of the Superconductor for 15 seconds Click Stop action Note Stereo Line Outputs are connected to your audio playback system e Select knob position 41 Play Knob Position click Play
31. ions click on Rec and Stop commands to respectively start and stop the Knob position recording process Actions NOTE The new sound will be named XX mp3 where XX is the selected knob position The sound will be automatically assigned to the XX position e Usethe Play File Drop down to select the file that you wish to play e Once you have selected the file use the secondary drop down to select how the file should be played Options include o Once o Loop e To play the selected file click the Play Button To stop the playback press the Stop Button CHAPTER 7 RECORDING AUDIO The Technomad SuperConductor features a dedicated line in to enable direct recording rather than file upload Once a microphone is connected to the line in audio recording can be controlled by the web interface and the LCM Note the SuperConductor records in MP3 format The Technomad SuperConductor features a dedicated line in audio input to enable direct recording rather than file upload Like any recording device audio levels should be set before making the audio recording connection to line level mixer output best and a quick test recording should be made The actual audio recording will take place through an audio input device i e microphone connected to the sound system that is connected to your SuperConductor through the dedicated stereo Line In connection on the back of the unit Recording audio from the web interface is carr
32. k on the appropriate tab Each screen is divided into two main areas e Left on the left hand side of each tab screen are the tab controls These allow you to set unit specific information CHAPTER 4 INTERFACE e Right on the right hand side of each tab screen are directions and identifiers for the controls on the left To exit from the Web control panel simply close your web browser If you wish to commit changes made during your session you must click the appropriate buttons e Settings if you change anything on the Settings tab you need to click the Reboot Button at the bottom to commit the changes to the unit s non volatile flash memory and reboot the SuperConductor e Knob Set and Scheduler click the Save Button to commit choices and changes Note if you leave the unit in the LCM you cannot make any changes The unit must be enabled and operating in normal mode for changes to be made through the web control panel Chapter Whether it s working through the LCM or the Web based interface the SuperConductor is easily controlled and configured to meet your specific audio needs The following represent the features of the Technomad SuperConductor e Status e Settings e Remote Control e Recording Audio e MP3Files CHAPTER 4 INTERFACE e Knob Management e Scheduling e Playing Sounds and e Security For this manual each of the above features where applicable will be divided into Web based in
33. l read XXXX with the first X blinking e To set the password turn the dial for each X until the appropriate digit is displayed Press the knob to advance to the next digit When finished press the knob again Upon successful authentication the LCD will display Main Menu Web Interface To login through the web interface e Open a web browser on a computer connected to the same network as the SuperConductor and browse to its IP Address for more information about setting this IP address see the Web Control Panel section in the Setup and Configuration chapter e When the web control panel opens a window will pop up asking you for your username and password Simply enter the password that you assigned to the unit during Setup and Configuration If you have not assigned a password the default password is 0000 The username is not required CHAPTER 3 SETUP AND CONFIGURATION CHAPTER 4 INTERFACE The SuperConductor provides two interfaces The Local Control Mode LCM and The Web Control Panel The Local Control Mode LCM is accessible through the knob and LCD panel on the front of the unit By turning the knob you can cycle through current music that has been uploaded to the unit and select one to begin playing immediately You can perform a number of configuration and settings tasks by logging in and navigating the LCM menu options Note these options will be described in more detail in the appropriate section
34. nob to scroll through the scheduled tasks Each one will display horizontally scrolling as O FILENAME Day datefield Time timefield Until untilfield Every everyfield Repeat repeatfield e Toenter the modification mode push the knob when the scheduled task you want to modify is displayed e The modification mode includes six options that can be scrolled through with the knob To select an option push the knob in when it blinks O EDIT DEL OFF ON DOWN UP EXIT Editing a Scheduled Task To edit a scheduled task via the LCM e Select the EDIT Option from the modification menu of the scheduled task you selected e When you select a schedule task to edit the LCM will present you with a list of menu items through which you can scroll To set a specific item push the knob when it is blinking Items include CHAPTER 7 RECORDING AUDIO File when you select this option use the knob to scroll through the library Push the knob to select the file When selected the LCM will display a confirmation message using the upper LCD line and lower LCD line that you have assigned the sound to the specific scheduled task You will then be automatically returned to the item list menu for the scheduled task Day when you select this option use the knob to scroll through the days Push the knob to select the day you wish when it is blinking When selected the LCM will display a confirmation message using t
35. nual is organized accordingly First the manual gives you an understanding of how to operate and interact with the SuperConductor Technomad SuperConductor User s Guide Page 3 of 65 CHAPTER 1 ABOUT SUPERCONDUCTOR e Next the manual provides an understanding of how to setup and install the device e After that the manual delves into the interfaces both Web and LCM e Finally each feature is broken down according to a tab in the web interface Where appropriate these feature based sections include the LCM equivalent Conventions This guide uses the following conventions to highlight certain words and phrases that differentiate their meaning visually This style Indicates italics Notes regarding special information about a feature bold A feature of the interface or functionality within the Technomad SuperConductor SuperConductor Unit For example Note You can also To open the document click on the Open button Chapter The SuperConductor Unit is a 1U rack mountable schedulable MP3 player and recorder Technomad SuperConductor User s Guide Page 4 of 65 CHAPTER 1 ABOUT SUPERCONDUCTOR Audio Specifications Playback e MP3 format audio 32kbps to 320kbps e Stereo or Mono e Fixed or Variable Bit Rate Recording e MP3 format audio 192kbps fixed bit rate stereo Physical Specifications Attribute Value Dimensions 19 w x 1 75 h x 10 d Weight 4lbs Data input
36. ob to select CHAPTER 4 INTERFACE e When the ROUTER IP option is selected the top line of the LCD will read Set Router IP and the bottom line will display the IP address in the format of XXX XXX XXX XXX with the first X of the first set blinking e To set each digit of the Router IP address turn the dial for each X until the appropriate digit is displayed 0 9 Press the knob to advance to the next digit e When all digits are set the top line of the LCD will display Router IP Address Set to then Click to Continue Date To set the Date e From the Main Menu turn the knob until the LCD reads DATE e Press the knob to select This will enter the Date Setting feature e The top of the LCD display will read the current date e The bottom of the LCD will flash the Set command Press the knob to set the date e When you activate the Set command the top LCD will then read Set Current Date and the bottom will read the current date with the first digit flashing To change the date simply use the knob to change currently activate digit blinking from 0 9 Press the knob to advance to the next digit CHAPTER 4 INTERFACE Time e When you have navigated through all the digits in the date the LCM will automatically retum to the top level menu There are two elements to time setting through the LCM e Manual time and e Timeserver e From the Main Menu turn the knob until
37. ogging in see the LCM Logging in Section of the Setup and Configuration Chapter To set the IP address e From the Main Menu turn the knob until the LCD reads IP ADDRESS e Press the knob to select CHAPTER 4 INTERFACE Subnet When the IP ADDRESS option is selected the top line of the LCD will read Set IP Address and the bottom line will display an IP address masking in the format of XXX XXX XXX XXX with the first X of the first set blinking To set each digit of the IP address tum the dial for each X until the appropriate digit is displayed 0 9 Press the knob to advance to the next digit When all digits are set the top line of the LCD will display IP Address Set to then Click to Continue From the Main Menu turn the knob until the LCD reads SUBNET Press the knob to select Router IP When the SUBNET option is selected the top line of the LCD will read Set Subnet and the bottom line will display the IP address in the format of XXX XXX XXX XXX with the first X of the first set blinking To set each digit of the subnet address turn the dial for each X until the appropriate digit is displayed 0 9 Press the knob to advance to the next digit When all digits are set the top line of the LCD will display Subnet Address Set to then Click to Continue To set the Router IP using the LCM From the Main Menu turn the knob until the LCD reads ROUTER IP Press the kn
38. r scheduled task To rename a file e Select the file to rename from the Rename File Drop down e Once you have selected the file enter the new name in the adjoining text field e Finally click the Rename Button Note file names cannot be longer than eight characters Remember to rename a file it must first be removed from any knob setting knobset or scheduled assignment scheduler To delete a file via the LCM e From the Main Menu turn the knob until the LCD reads LIBRARY CHAPTER 7 RECORDING AUDIO e Press the knob to select e The top line of the LCD will read Sound Library e To navigate to a file to delete use the knob to scroll through the library When you reach the file you wish to remove push the knob This will display three options for the file o No return to the library and take no action against the file o Rename rename the file o Delete delete the file e Use the wheel to scroll through the options until the Rename is flashing Press the knob to select the file e When you select a file to rename the top line of the LCD will read New Name and the bottom line will be the file with the first character flashing Turn the knob to cycle through numerical and alphabetical characters Press the knob to advance to the next letter When finished you will be returned to the top level of the Library Deleting Files Files uploaded or recorded to the unit c
39. rademarks of their respective owner Technomad SuperConductor User s Manual Page of 65 Trademarks and GCopyrigHlbus ari AAA d d diodes i Cons rad ds i About AAA A 3 A vette cine Ce eta Gidea cee 3 Values and Benelils asa ans 3 Undertanding this Manual enne tnnt 3 CONVENON Se amit taceo edu quida doa aa 4 superConductor Uta 4 Audio SDecITICAtOrls cura era eius cie Rea pani ee euren een rebua CS qe HERE 5 q lone AE E RRE 5 aieo pps id 5 Physical SPOCHIGANONMS Gaita ass 5 Local Control Mode EOM sie edo ditio ate lis 5 A cn stet eb eta onte Aen 6 AAA uas ee uhr metet pur ie ER ena E QA 6 Front Eel mto pe dedii puma nance edid reta to tt que 6 Back patei Les aero acta t rito tres ob eO la van Gees mu vM Wt 6 ML Pes atacada iia 7 A O edo dul a eodd 7 Setup and CONTO ur a tit t etae kl eS el Sl 8 Configuring the SUperGor ctf s ci n 8 The LCM TE 8 A toe EE D E Mn pA NEN EE 9 A ox adio e A qai O DIRE 10 A eti cat ete Ga in Bue cid 10 O ce uineis tet on esse utimur 11 The Web control PA os ecu cbe quist ed iaa teas i dum de ap 12 GIA Eoi eot t bs 15 A i tua anc 15 WV SD nice LER 15 prz gis eU 17 The Local Control Mode ECM a itte db e e ta nce eds 17 zs irpo res E D E NN 18 CUIGK ACROSS on e ended Medusa ood wea eaten etin 18 Wel Control Panel saos etse p A 19 A ets rdum ecd M E Me LE 20 Working With the Super COTIQUCIO s cootra datus ect ast e rds 20 Sas casses utt destra nd Lotti ati Satan AR 2
40. ropriate digit is displayed 0 9 Press the knob to advance to the next digit CHAPTER 3 SETUP AND CONFIGURATION e When all digits are set the top line of the LCD will display Router IP Address Set to then Click to Continue To set the IP address via the Web control panel e Plug the unit via the RJ45 port to a computer using a crossover cable e Configure the computer s IP address to an address that matches the configuration of the unit So if your SuperConductor is set to 192 168 1 2 default you might set your computer s Local Area Connection to the following o P 192 168 1 200 e In configuring the unit the first time you do not need to worry about the gateway IP or DNS servers when manually setting your computer s network connection e Once you have configured your computer with the appropriate IP address so that it exists within the same network as the unit open your web browser to 192 168 1 2 This will allow you to configure the unit via the Web based interface CHAPTER 3 SETUP AND CONFIGURATION ODTOD O OL resssis2 16s 0s9ndexnm y NG Goose Technomad SUPERCONDUCTOR SETTINGS military audio systems STATUS 0 14 08 14 50 Advertisement Visit Technomad s website by clicking on the Technomad logo above e When first entering the Web based interface you will be asked to authenticate your identity Simply enter the password the username field is not used The default password is 0000
41. sword and the bottom will read XXXX with the first X blinking e To set the password turn the dial for each X until the appropriate digit is displayed Press the knob to advance to the next digit When finished press the knob again This will automatically commit the settings and return you to the main LCM menu CHAPTER 4 INTERFACE CHAPTER 6 REMOTE CONTROL The remote control feature allows you to play sounds on the SuperConductor unit from within the web interface The Remote control feature by default is enabled To play a file from the web interface CHAPTER 6 REMOTE CONTROL Technomad SuperConductor Control m US ox te SD A http 82 48 141 191 control html wy aA Gly Google Qa Technomad SUPERCONDUCTOR SETTINGS military audio O SUS te ms m Ww comas es E23 Remote Control show the state of the remote control if enabled is possible to Remote Control enabled control the device by the commands available on this page Knob Lockout Knob Lockout enable or disable the knob play command functionality Play Sound play section Play Sound Play knob position select a knob position to play Play knob position select j ONE Play stop Play file select R one 1 Play stop Play file select a file to play from library Record Sound Record Sound record section Recording status stop Knob position select a knob position Act
42. terface and LCM Status eoo Technomad SuperConductor Status page lt gt D eo xx eun http 192 168 0 99 index html vx v an Google Q Status display Current Time 10 14 08 14 50 Advertisement a 75 Visit Technomad s website by clicking on the Technomad logo above Status Inactive Timeserver Disabled Current refresh rate 2 seconds Set refresh rate to 2 seconds 5 seconds 10 seconds The Status tab provides a quick overview of the unit s current status e Current Time the units current time either using the unit s internal clock or a timeserver This can be specified in the Settings tab Volume the unit s current volume This can be specified in the Settings tab e Mode the current state of the unit Options for this include CHAPTER 4 INTERFACE Settings O O O Inactive the unit is currently idle file name f a music file is currently playing it is displayed here Configuration the unit is in LCM mode Timeserver the IP address of the time server if specified Current refresh rate how often the Web based interface will refresh To change the rate click the appropriate button O O O Refresh every 2 seconds Refresh every 5 seconds Refresh every 10 seconds Web Based Control Panel military a audio systems SETTINGS CONTROL Technomad SuperConductor Settings http 192 168 0 99 settings html MP3 UP
43. the LCD reads TIME e Pressthe knob to select This will enter the Time set feature e The top of the LCD display will read the current time e The bottom of the LCD will flash the Set command and the Timeserver command Use the knob to select either the Set option for manual or the Timeserver option to specify timeserver settings Manual To set the time manually e Select the Set command from the Time menu by pushing the knob This will display the following LCD configuration e The top of the LCD will read Set Current Time e The bottom of the LCD will be split into H for hours and M for minutes CHAPTER 4 INTERFACE o To set the hours press the knob when the current value for the hours is blinking Then use the knob to select a value from 1 24 When you set the hour the minutes will blink o To set the minutes press the knob when the current value for the minutes is blinking Then use the knob to select a value from 1 60 o When you set the minutes the LCM will return to the top level menu TimeServer To specify timeserver settings e Select the Timeserver command from the Time menu by turning the knob to set the command blinking and pushing the knob to select it This will display the following LCD configuration o The top of the LCD will read Timeserver o The bottom will have three additional commands Off On e When blinking press the knob to
44. the same instructions as above Note Any sounds triggered from the front knob and screen interrupt any scheduled sounds playing but the scheduled sounds resume at the next event once front knob playback stops You can also initiate playback of audio through CGI command sent to the IP address of the unit For example CHAPTER 11 PLAYING SOUNDS e Example of link to play Sound assigned to knob position 7 with play mode one once o http 192 168 0 30 BAS cgi rc 18sound 78plmod 0NE e Example of link to play sound in library o http 192 168 0 30 BAS cgi rc 2 amp 8name BS amp plmod ONE e Example of link to stop sound playback o http 66 92 95 105 BAS cgi rc 1 amp sound 0 For a more comprehensive listing of CGI commands and correct syntax see Appendix A Chapter Security The SuperConductor includes security features that require a password for playback from either the web interface or the LCM Web Interface In order to access the Control tab of the web interface you must enter the authentication password specified in the Settings tab Upon successful authentication you will be able to access all of the tabs LCM In order to access the LCM you must provide the assigned password CHAPTER 11 PLAYING SOUNDS e First set the unit into local configuration mode LCM by turning the knob one turn past the last music assignment In a new unit you shouldn t have any assigned slots e Press the knob for 5 seconds
45. then perform two actions by turning the knob Assign Audio Record Audio e Select the Assign Audio option and press the knob e The top line of the LCD will now read knob position Assign Sound Use the knob to cycle through the library of sounds The names of each file will appear in the bottom line of the LCD CHAPTER 7 RECORDING AUDIO e When you have identified the file to assign to the selected knob position press the knob You will be returned to the top level menu Clearing Knob Positions The knob positions can be cleared via the web interface and the LCM Web Interface Knob positions are cleared in the web interface from the Knob Set Tab e00 Technomad SuperConductor Knob set e 4 JB CC CO Ct E CO no 1 82 48 141 191 knobset html wy N Technomad SUPERCONDUCTOR SETTINGS 1 military audio systems mu n Knob sound assignment In the field Knob enter the number of the knob to Fie Mode Knob File SR WEATH LOOP sil not set na m not set E SR_ALERT LOOP SR_AIRRD not set Je E ais su sick once 9 6 su never not set na E e BU_QUART ONCE 20 BU_OFFIC assignments power fail save A warning will appear when not all assignments are otse na si 23 BU_GUARD once m 24 Bu rinsr not set na BU_ASSMB ONCE BU_ADJUT Kank assignment igen Shows the SO_ARMY LOOP SO_AIRFR current assignment of all 64 knob FX_EXPL2 1 i FX EXPL3
46. tructions e Scroll past last knob setting i e 41 FX_XPL e Press encoder center button for 5 sec to enter LCM dialog Then click again to enter LCM Enter password by tuming and pushing the encoder switch e Scroll to Schedule e Push dick encoder button e Click encoder clockwise beyond scheduled lines see Add new line e Press encoder button in wait e Scroll to file e Push click encoder button on File wait e Scroll to see various files Push click on a file to select Wait then push encoder button on Edit wait e Right click to Day Scroll right to Daily Monday etc Push click on choice and wait CHAPTER 3 SETUP AND CONFIGURATION e Backto Edit Push click then Right click scroll to Time Push click on Time Set time using the encoder push and click functions wait e Push click on Edit to continue editing or scroll to Exit and push click wait e Push dick to Exit and Save Wait e Scroll right to Exit and Push click Toggle right with encoder switch between Yes or No e Push click Yes to Exit e This brings you to the IP display e Resetthe IPAM IP Address To set the IP address using the LCM e From the Main Menu turn the knob until the LCD reads IP ADDRESS e Press the knob to select e When the IP ADDRESS option is selected the top line of the LCD will read Set IP Address and the bottom line will display the IP address in the format of XXX XXX XXX XXX
47. ved to the library and the new recorded sound assigned to the selected position e To record the audio turn the knob until the option on the bottom line of the LCD reads record Press the knob to begin recording The bottom line of the LCD will read recording CHAPTER 7 RECORDING AUDIO e To stop recording press the knob again e When you stop recording the LCD will display a success message and then present options for playback mode for the newly recorded file o Loop o One Time o Push Hold e Once you select a playback mode you will be returned to the top level menu The Technomad SuperConductor includes 1GB of non volatile storage for uploaded and recorded audio files in mp3 format The SuperConductor has the following audio file requirements e MP30nly at present but will play any bitrate up to 320kbps fixed or VBR Audio files can be uploaded through the MP3 Upload tab in the web interface CHAPTER 7 RECORDING AUDIO a J E http 82 48 141 191 upload html SUPERCONDUCTOR SETTINGS military audio systems il w L az E e press m powa ai o e a 2 A A 8 2 it e To upload a file e Click the Browse Button to open a dialog box allowing you to find the file on your hard drive e When you have selected the file the dialog box will close and the file namellocation will be displayed in the MP3 File textbox e Click t
48. with the first X of the first set blinking e To set each digit of the IP address turn the dial for each X until the appropriate digit is displayed 0 9 Press the knob to advance to the next digit e When all digits are set the top line of the LCD will display IP Address Set to then Click to Continue Subnet To set the subnet using the LCM CHAPTER 3 SETUP AND CONFIGURATION e From the Main Menu turn the knob until the LCD reads SUBNET e Pressthe knob to select e When the SUBNET option is selected the top line of the LCD will read Set Subnet and the bottom line will display the IP address in the format of XXX XXX XXX XXX with the first X of the first set blinking e To set each digit of the subnet address tum the dial for each X until the appropriate digit is displayed 0 9 Press the knob to advance to the next digit e When all digits are set the top line of the LCD will display Subnet Address Set to then Click to Continue Router To set the Router IP using the LCM e From the Main Menu turn the knob until the LCD reads ROUTER IP e Pressthe knob to select e When the ROUTER IP option is selected the top line of the LCD will read Set Router IP and the bottom line will display the IP address in the format of XXX XXX XXX XXX with the first X of the first set blinking e To set each digit of the Router IP address turn the dial for each X until the app
Download Pdf Manuals
Related Search