LEP Power Supply for Mercury 50 Watt AC Lamp User`s Manual
Contents
1. LEP Power Supply for Mercury 50 Watt AC Lamp User s Manual This manual covers the following power supplies P N 990002 P N 990002 1 D Ludl Electronic Products Ltd Revision B p n 90M014 10 9 2003 Contents Contents JASS con ad 1 1 0 Safety Standards cw wd isi in ee 2 1 1 Safety Information aa 2 High Voltage and Ultraviolet Exposure uuussssenennnnnnnnnnnnnnnnnnnnnnnn nennen 2 1 2 FUSE Information ae een A una AEPA C RAN Eee 2 1 32 WAMING o AA sc sae ce ca ee 2 1 4 Front Panel siprann eena nw cea ces maat 3 Main Power S 1741107 1 POPBEPRRERPREPRERBAEFEPEFREEPEUERERE PABEEEEELEEEPEPRPEFEHEFELEFEEEERPERBUEEELEFLELTES 3 1 5 Rear Panel ara ee 4 2 0 Installation u areas nes area 4 2 1 Failure of Lamp to Igniles susana nenne 4 3 0 SPEC INI CATIONS MAMM 5 Lamp Replacement History nnnnnnnnnnnenenennnnnnaanananannnennnnnnanannnnnnnnnnnnnnaaaaa 7 1 0 Safety Standards 1 1 Safety Information High Voltage and Ultraviolet Exposure The lamp connector at the rear of the power supply has a maximum of 230 volts RMS e Do not turn on the power supply unless lamp socket is attached e Do not operate the power supply unless the lamp socket is properly installed in a suitable lamp house e There are no user serviceable components inside the case Please refer all service to your dealer Failure to observe these precautions will result in exposure to high voltage and ultraviolet li2. ght 1 2 Fuse Information This unit is internally fused by a re settable thermal breaker rated at 3 0 amps In the event of an overload wait 2 minutes for cool down before pushing the breaker reset button located on the rear panel If the unit trips again service is required 1 3 Warning Notice The high voltage warning symbol a lightning bolt in a white triangle on the rear panel indicates terminals have voltage and should be handled appropriately 1 4 Front Panel The recessed push button will reset the lamp timer to zero This is used when a new lamp is installed Typical lamp life is 100 hours o slo 0 LAMP TIME RESET ARC LAMP POWER SUPPLY SOW HBO AC 990002 Main Power Switch The main power switch turns lamp on or off When switched on the lamp will glow dimly for a few seconds After 2 minutes the bulb will grow to its full brightness A hot lamp will not light immediately and may take 5 minutes to light 1 5 Rear Panel MANUFACTURED BY Lo HAWTHORNE N Y 000000000000 60808060 OCOD 0809808 000000 0090900650009 o 000000000000 2 000000000000 A 000000000000 8900060000009 2000000000000 000000000000 EI 2420 8208 0 2 OO 000000000000 iste 119147 REFER SERVICING TO CONFORMS TO QUALIFIED PERSONNEL NO USER UL STD 3101 1 SERVICEABLE COMPONENTS INSIDE O WARNING 5 HIGH VOLTAGE O INPUT 117V AC 200W 50 60Hz HBO 50 AC l POWERSUPPLY 2 0 Installation Verify
3. the L1 L2 switch on the rear panel is set consistent with the marking on the lamp shipping box Ensure that the lamp is properly mounted in the socket and the socket is installed properly in the lamp house Connect the cord from lamp socket to the connector on the rear panel Verify lamp type setting and connections Connect the line cord to a 110 VAC 60Hz power outlet Turn on main power switch 2 1 Failure of Lamp to Ignite The lamp will usually turn on within 10 seconds If the lamp fails to ignite it is usually an indication of a bad lamp open cable or socket Note Refer all service to your dealer 3 0 Specifications Input 117 VAC 10 60 Hz 3 Amps Output Open Circuit 230 VAC Current L1 1 3 Amps Lamp Volts 39 45 VRms L2 1 45 Amps Lamps Volts 33 39 VRms NOTES Lamp Replacement History Date Lamp Type Elapsed Hours Initial Ludl Electronic Products designs and manufactures a wide range of automation accessories for microscopes and instrumentation www lud com Ludl Electronic Products Ltd 171 Brady Avenue Hawthorne NY 10532 Voice 888 769 6111 Fax 914 769 4759 Support ludl com Sales ludl com Copyright 2003 Ludl Electronic Products Ltd
Download Pdf Manuals
Related Search