Marine Display User`s Manual Marine Line
Contents
1. e connection to other types of power sources Warning s using other types of mounting or placement of the product e connection to other devices than those for which the monitor has been designed will void any and all warranties of the product and the manufacturer will not be responsible or libel for any bodily injury or property damage either directly or indirectly caused by such non intended use of the product Intended Markets These products are developed primarily for sales and installation in countries within Europe and North America The products comply with all regulations and directives issued by the European Union and by authorities in the United States The products are not intended for sales and or installation in countries which reguire other or additional mandatory approvals than those reguired by the authorities of the Warning European Union or the United States Consult the product identification label or product specification for regulatory approvals that apply to this product Safety Precautions It is important that you read through the following notes of Safety Precautions to avoid any damage to the Product yourself or other property Following these precautions will also ensure that you get the best use of the Product of high voltage inside there is a risk of bodily injury or death Only authorized and Y DO NOT OPEN THE PRODUCT There are no user serviceable parts inside Because gualified service personn2. lamps All monitors have the facility to adjust brightness Never set this at maximum since this will cause the lamps to decay faster A setting at 50 will be sufficient for use in office environment Gradual change of color As the backlight lamps ages they will show a warmer color temperature which can be perceived as more yellow for white color than it was initially when the monitor was new There are color filters in the panel which also will age and add to the yellowish color tone You can usually from the monitors OSD set your own color and by setting the value for blue higher than red and green will change the color temperature back to more normal However the blue color filter has lower translucence so the conseguence is that you will get a lower brightness 28 Troubleshooting Start your trouble shooting with the following actions Possible power problem e Make sure power is connected If you switch the monitor off and then back on the diode on the front should show green light Some models have a main power switch next to the power inlet check that this is set to on If you have a model without power adapter and still the no green light it s not a power problem e lf not check your power connection to the 12V 24V adapter and to the wall There is a similar diode on the 12V 24V adapter that should show green light e If not the adapter might be broken If you have another adapter of the same type you can veri
3. ojojo aT ass 5 ojoo vesa e 60 87 8 olojo oa e a o ololo oa s o ooo a e ose 5 ooo a e e7 s ooo w oa ao o a CNC w oa o ooo o o se s oa la eo Jao so o KC KEN NE we e sm wer Js Loco a e sz Js ooo 1 Interlace display T The display mode A is a downscaled Pseudo display Caution tL Specifications MAL 15576 amp MAL 15576G Display Environmental Input signal Power Functionality International standards Warranty Screen size Format Brightness candela m2 Contrast Resolution Megapixel Viewing angles H V Color depth Panel type Backlight type Temperature Celcius Humidity non condensation Air pressure Connections Power supply Power consumption Automatic adjustment OSD for settings Speakers Luminance compensation Pivot Protective glass Touch panel Dimming Sunlight Readable DICOM pt 14 preset IT certificates Replacement warranty 15 304 x 28 mm 4 3 250 cd ma typical value 700 1 typical value 1024x768 0 8 Mpix 160 150 typical value at CR 10 1 262K 16 2M TN CCFL Operating Storage 10 40 C 20 60 C 30 75 10 90 700 1060hPa 500 1060hPa 1 DVI I 29 pin connector Compliant with DVI 1 0 2 S video connector Color signal 0 286Vp p 75 O Brightness signal 1Vp p 75 Q 3 BNC connector Composite signal 1Vp p 75 0 4 Audio signal pin jack3 5mm connector 0 2 2 0 Vrms 5 RJ 4
4. 60 C 30 75 10 90 700 1060hPa 500 1060hPa 1 DVI I 29 pin connector Compliant with DVI 1 0 2 S video connector Color signal 0 286Vp p 75 O Brightness signal 1Vp p 75 Q 3 BNC connector Composite signal 1Vp p 75 0 4 Audio signal pin jack3 5mm connector 0 2 2 0 Vrms 5 RJ 45 connector Extend interface OSD control 12Vdc 5A Approx 50W Max Less than 4 5W in stand by mode Yes via OSD PreVu Yes 2 pcs ALC Yes software required Add G to type number Optional ELO SAW USB or RS 232 Standard for Marine 0 100 Optional Clearbase Barten UL cUL FCC B CE WEEE RoHS Two 2 years 22 Specifications MAL17776 amp MAL17776G Appearance Net weight Approx 5 5 kg Measurements WxDxH 378 x 70 x 314 mm w o base Mounting Kensington lock Yes prepared VESA standard 100 mm 372 23 Specifications ML19776 8 19776G Display Screen size Format Brightness candela m2 Contrast Resolution Megapixel Viewing angles H V Color depth Panel type Backlight type Environmental Temperature Celcius Humidity non condensation Air pressure Input signal Connections Power Power supply Power consumption Functionality Automatic adjustment OSD for settings Speakers Luminance compensation Pivot Protective glass Touch panel Dimming Sunlight Readable DICOM pt 14 preset International standards IT certificates Warranty Replacement war
5. the panel behind the cover lid Please refer to the diagram on the next page for the connector configuration Connect Power Adapter and Cable Connect the round shape plug end of the AC DC adapter to the DC Power input connector of the LCD monitor Connect the female end of the power cable to the AC power input receptacle on the AC DC adapter Then plug the male end of the power cable into an grounded AC outlet T Make sure you use the AC to DC adapter delivered with the product Caution Connect Signal cable On next page you can see which input connectors there are available on your monitor and which cable you should connect depends on your source for the input signal VGA DVI HDMI or Displayport output from a PC If your source is VGA analog then use either a VGA to VGA cable for connection to the VGA connector or a VGA to DVI I cable for connection to the DVI I connector on the monitor If your source is DVI digital then use the DVI DVI cable supplied with the monitor and connect to the DVI I connector on the monitor If your source is HDMI or Display Port then you need a converter from HDMI or Display Port to DVI Then you connect the DVI DVI cable between the DVI I connector on the monitor and the converter There are also available HDMI or Display Port to DVI cables that can purchased from your local reseller Video input from camera or other NTSC PAL signal generating eguipment Use S video cable or for Composite video BNC
6. 5 connector Extend interface OSD control 12Vdc 5A Approx 35W Max Less than 4 5W in stand by mode Yes via OSD PreVu Yes 2 pcs ALC Yes software required Add G to type number Optional ELO SAW USB or RS 232 Standard for Marine 0 100 Optional Clearbase Barten UL cUL FCC B CE WEEE RoHS Two 2 years 20 O Specifications MAL 15576 amp MAL 15576G Appearance Net weight Measurements WxDxH Mounting Kensington lock VESA standard 1 Units with Protective glass ML15776G or Touch panel are 63 mm deep Approx 3 3 kg 375 x 59 x 282 mm w o base 1 Yes prepared 75 mm 21 gt Specifications MAL17776 amp MAL17776G Display Screen size Format Brightness candela m2 Contrast Resolution Megapixel Viewing angles H V Color depth Panel type Backlight type Environmental Temperature Celcius Humidity non condensation Air pressure Input signal Connections Power Power supply Power consumption Functionality Automatic adjustment OSD for settings Speakers Luminance compensation Pivot Protective glass Touch panel Dimming Sunlight Readable DICOM pt 14 preset International standards IT certificates Warranty Replacement warranty 17 337 x 270 mm 5 4 350 cd ma typical value 1000 1 typical value 1280x1024 0 8 Mpix 160 150 typical value at CR 10 1 262K 16 2M TN CCFL Operating Storage 10 40 C 20
7. 9 format 16 10 Will scale the picture to 16 10 format P OSD Display Positioning of the OSD on the display H Position Move position of the OSD display horizontally V Position Move position of the OSD display vertically Language Select language for OSD Returns to Main Menu and will from then on show the OSD in the selected language You can choose between English French German Italian Spanish or Japanese Key lock A function with which you can lock the OSD menu to settings you have made When you then try to enter into the OSD you will stop at source menu To enter into this function you must click on the OSD wheel 3 times within 2 seconds You also do the same when you want to un lock the Key Lock Bright bar Special setting used to select if the setting bar for Brightness adjustment shall be shown on the monitor or not Active only for when you adjust the brightness by turning the control wheel without having entered the OSD menu You select YES or NO if it should be shown or not r ALC Automatic Luminance Control ALC is a function which can be set to ON or OFF When set to ON it will automatically increase the Brightness setting to off set the wear on the backlight lamps It has been developed mainly for when you select Clear base Barten color mode and is always ON in that mode It will make the monitor to better comply with the DICOM reguirements during the full life of the product and not only at the time of deliv
8. C Power cord e DVI to DVI cable e DVI to VGA cable e 3 5 mm Audio cable Optional Items e The Base unit with 4 Screws and Screwdriver e S video cable e DVI to VGA 8 DVI splitter cable Optional Items for Touch panel e USB cable e Serial RS 232 cable e CD ROM with Touch panel drivers If any of the above items are found missing or if you wish to order the optional items please contact your reseller The Monitor has Video Electronics Standards Association VESA standard mounting holes tapped into the rear panel The standard holes are M4 set 100 mm for 17 and larger monitors or 75 mm 15 monitors apart If you intend to mount the monitor on the wall we strongly recommend that you use wall mount kits with attached M4 10mm screws and which can hold a load of more than the weight of the monitor Ensure it is securely and safely installed If you mount any device using these 4 holes on the back of the panel you must not use use screws longer than 10 mm Longer screws will cause damage which is not covered by the product warranty Warning oooonono vooonovno The position of the connectors can vary between models and they may or may not be covered with a flap a o o o o UL Input signals No tools are required to connect the LCD monitor to your PC or other device Simply follow the instructions outlined in the next few pages Connectors for the signal cables and power are located on the back of
9. MARINE MONITOR AU information contained in this manual is subject to change without notice Marine Display User s Manual Marine Line MAL15776 MAL 15776G MAL17776 MAL17776G MAL19776 MAL19776G Preface Product features Intended markets Safty Precautions Regulatory reguirements and approvals labeling FCC Information Warrenty and Limitation of Liability Cleaning the Product Disposal of the Product Getting started Input signals OSD Adjustment Functions Chart of OSD Adjustment Functions Applicable Signal Timings Specifications Special Considerations for LCD Panels Troubleshooting Contact information o O N WO 0 N 10 12 14 16 18 20 27 29 31 Preface Thank you for purchasing this LCD Monitor To get the full benefit of the features that this product offers you it is important that you read this User s Manual which among other things will explain how to properly install and operate the monitor In this user guide there are detailed product specifications explanations for many of the technical terms used in this manual as well as information on regulatory approvals cleaning service instructions warranty terms waste disposal and some other useful information It is of utmost importance that you carefully read and follow the safety instructions and safety notices included in this User s Manual Failure to comply with these instructions could in some instances cause bodily harm to y
10. akes actions taken by any third party any other accidents intentionally or negligently improper use of the product by the user or any use under other abnormal circumstances e the use or inability to use this product e the use for other purposes than the intended use as described in this document e malfunctions caused by the combination of connected devices Cleaning of the Product Be careful when cleaning the plastic housing of the panel so that no liquid or other objects will drip down into the product through the ventilation holes This could cause electric shock and damage the product Caution Normal dust and lint particles can be easily wiped off with a soft cloth tissue For grease or dirt that is more firmly fixed to the product the use of a soft and dry micro fiber based cloth tissue will normally remove it all You can also use a mild liquid detergent mixed with water for cleaning together with a soft cloth tissue This will clean both the cabinet and the LCD panel well For the LCD panel you can also use isopropyl alcohol based liquids without abrasive or non ammoniac glass cleaner When cleaning the LCD panel you will get the best result if you clean the panel when its surface has cooled down to normal room temperature On a warm panel the liquid evaporates too quickly leaving traces of the cleaning Afterwards wipe the surface dry with another soft cloth tissue When cleaning the cabinet do NOT use thinner benzen
11. cables Connect Audio Cable Connect an audio output device to the monitor with the included stereo mini cable using the 9mm audio jack RJ45 Connector If you want to control the On Off and OSD at a distance from the monitor there is an optional external control box available This box is connected with an RJ45 cable When you disconnect the cord cables be sure to hold the connector and not the cable itself Also make sure you use cables and connectors of high guality Caution 12 Input signals 15 amp 17 Connections TI j5 a Om RIH v gt To Computer Optional l mmm Composite video source S video source AC Outlet gt Optional m HE HE po Cm Be a gt To Computer Optional LE mmm Composite video source Optional e S video source DVI I to DVI D amp VGA splitter cable ee ll DVI Source NI c VGA Source OSD Adjustment Functions LED T Indicator Control Dial The Control Dial is a multi functional device located behind the LED Indicator on the right side of the front bezel It has three movements rotate upward rotate downward and press inward as a button 1 Power On Off Press the Control Dial to power the unit on from the off stage the display is off To turn the power off press the Control Dial and hold for at least 1 second until the display tur
12. creen saver that moves around on the screen so that no static image is constantly shown Image sticking Slow operating in cold environments The thin film transistors contain some liquid that will cause them to operate slowly in cold temperatures When temperature inside the panel has increased to normal room temperature the speed will be up to normal again Special Considerations for LCD Panels The components that have biggest influence on the useful life of the product are the backlight lamps These are made of CCFL Cold cathode Fluorescent Lamp Over time these will decay and give less and less light They generally have a spedification of 40 000 hours before they are worn out If they are constantly on one year of use corresponds to just over 8 000 hours and thus a life of 5 years There are ways to improve the useful life The most radical and efficient way is to always switch the monitor off when not used The second best is to use the Power Save feature within the PC s DPMA system This will not switch off the monitor entirely but the backlight lamps will be switched off which is the important thing When you start to use the keyboard or mouse the monitor will be switched on within a couple of seconds PLEASE NOTE THAT A SCREENSAVER WILL NOT SWITCH OFF THE BACKLIGHT LAMPS AND THUS IS NOT A SOLUTION FOR LONGER LIFE The higher the luminance is set on the monitor the greater is the wear of the backlight
13. cs and color filters There are different technologies used with each having its advantages and disadvantages resulting in end user products with different specifications even when taken from the same manufacturing batch Below are explanations to some observations that can be made and which are not considered defects since they are merely problems inherent in the technology of LCD monitors Over time the performance of the panel will also change Native resolution All panels have a fixed number of pixels in both horizontal and vertical directions For instance is a 19 panel normally built with 1280 pixels horizontal and 1024 vertical giving a native resolution of 1280x1024 At this resolution you will get the sharpest picture and it is therefore recommended that you use the native resolution Thru scaling technologies it is possible to use other resolutions but the picture will be less sharp Some text will appear to have shadows Native color temperature Most commonly LCD panels are manufactured to have a color temperature of 6500K Kelvin degrees for full white picture The color temperature can vary with shade of grey being showed For instance it could be 7500K at 50 grey and more than 9000 at 90 grey For an individual panel the color temperature at full white can also vary by 15 Inside the panel there is a color filter and over time this will age and become more yellow in its color tone Therefore over time the col
14. d and developed for use as a visual output device for direct connection to a Personal Computer and PC compatible devices as well as other video generating equipment such as cameras The product will accept industry standard video signals coming over cables with industry standard type connectors The product will operate and function properly in normal office environment and under conditions as specified in the Product Specification chapter Attempting to use the product for any other purpose than its intended use or connecting to other devices could cause damage to the product and or to other property and equipment There could also be a risk of bodily harm to yourself or other Warning persons The product operates on 12V some on 24V DC power and must be connected thru the AC 100 240V 50 60Hz to12V DC adapter or 24V DC adapter which is included with the product Power to the adapter should be coming from an ordinary grounded AC 100 240V power outlet Never try to connect the product to any other power source than the 12V 24V adapter delivered together with the product There would be a risk of electrical shock which could cause bodily harm possibly even death Most certainly such electrical shock will Warning damage the product The product can also be delivered with certain options installed Such options could be touch panel or other special accessories All other uses of the product including but not limited to attempts such as
15. e or alcohol as these might damage the plastic and cause the paint to peel off Do NOT use organic solvent such as acetone and toluene when cleaning the panel gt Warning If you use any liquid for cleaning you must first un plug the power to the monitor and not connect it again until you are certain that all the liquid particles have evaporated Failure to do so could result in electric shock gt Warning Do not use any tools with hard or sharp material for cleaning The panel can very easily be scratched or damaged from such tools gt Caution Do not press hard on the panel when cleaning This could cause damage to the LCD panel element gt Caution Disposal of the Product Do not dispose of the unit with general wastes The monitor has been manufactured to comply with the EU directive on RoHS Reduction of Harmful Substances but even so the LCD panel contains a small amount of mercury and the monitor should therefore be disposed of according to local laws Please get information from your local re seller how collection is handled in your country For countries that are members of the EU the WEEE directive applies and proper marking is on the product label affixed to the monitor Getting started Before operating this monitor please make sure that all items listed below are present in your delivery Standard Items e The LCD monitor panel e Users manual e Warranty booklet e AC DC adapter e A
16. el should maintain the product Warning Cautions when setting up Do not put the unit on unstable places on a wonky table or in an inclined ZN place which might cause injuries if it falls down Caution Do not place the unit where it is subject to direct sunlight or near any heating device This could cause overheating resulting in damage to the product and eventually causing a fire Caution p y 9 Cautions when using Do not put the unit in such a place where there is bad air circulation dust humidity oily smoke or steam It may lead to a fire Warning Do not put any metal materials or flammable foreign objects into the unit through the vent holes It may lead to electric shock and or fire Immediately disconnect the unit from the power outlet and contact your Caution ocalre seller for service i Scratching or hitting with hard objects may damage the unit Caution Safety Precautions gt Warning gt Caution down These positions may cause the heat that the unit generates to accumulate inside the unit Such overheating can cause damage to the Do not use the unit turned over on its back put on its side or upside S product and eventually start a fire break every hour to reduce eyestrain Failure to do so could cause injury to When using the unit for several hours you should take a 10 15 minute your eyes Abnormal circumstances gt Warning gt Warning A War
17. ery In other color modes you can set it to ON or OFF but since you have the ability to manually adjust brightness in these color modes the recommendation is to set it to OFF m Recall If you execute Recall the monitor will be reset to values that are default values at time of delivery Mute You can set this to ON or OFF and the function is to switch off the speaker sound Volume You can adjust the sound volume from the built in speakers Monitor info This will show some information of the monitor which are useful for service The information contains the following Model number Firmware version Operating Hours ALC check Dimming check Resolution and Color mode 1 Only available if the monitor input source is VGA 2 Only available if the monitor input source is S video or BNC azl o Applicable Signal Timings The following features are optional Marine Dimming To lower the brightness from 100 to 0 This is especially useful on ships during night use in order to keep night vision intact T 18 L Applicable Signal Timings The display may not work correctly with timings other than listed below Recommended timing Applied timing A Pseudo display timing Resolution Frequency Display mode Horizontal Vertical 15 17 19 Horizontal Vertical kHz Hz TK eo a as Ja ololo eo are Jz o o o eo Jao os 5 ooo eo Jao as Js NSN KOHEN ee eo se oc eo ds Te ololo Js ar Jz
18. fy by using that adapter e If yes there is a problem with the panel which should be repaired e If yes then it is not a power problem Possible signal problem e If picture is not stable or not shown at all or you get No Sync then check connection of the signal cable and graphic board settings e If cable connections and graphic board settings are OK then try the following e Switch monitor off Wait 10 seconds and switch it back on e Re boot the PC e Test monitor by connecting it to another PC e lf nothing of this helps then there is something wrong with the monitor and it should be repaired Contact your local reseller for assistance Troubleshooting Barten curve Curve used to emphasize areas of a digital grayscale where the human eye have trouble discerning similar shades of gray named after its creator Dr Peter G J Barten DDC This unit conforms with DDC 2B and VESA standards The DDC function reads information stored in the monitor about its capabilities It communicates over the 15 pin D sub connector and the 24 pin DVI D connector and it takes place during start up of Windows It sets the detailed information of the color LCD display in the system file in order to achieve Plug amp Play The video cable must be connected for reading of the information to take place 1 DDC Display Data channel and 2 VESA are registered trademarks of Video Electronics Standards Association Kensington Anti Theft Secu
19. ightness VIDEO S Video Contrast Contrast VIDEO BNC Display Hue MAIN MENU COlor Mode O e o am Mode Clock Phase Saturation Black Level Black Level Management 7 Management Monitor Info fo Monitor Info DVI DVI VIDEO S Video tL Charts of OSD Adjustment Functions When you enter the OSD you first come to the menu for selection of input so if you have 2 sources connected i e PC and camera you can quickly switch from one source to the other When you click on another source you will leave the OSD system If you want to proceed to the regular Main Menu you must choose MAIN MENU Source selection e DVI I VGA e DVI I DVI e VIDEO S video e VIDEO BNC e MAIN MENU Main menu Exit Auto setup 1 Image OK Brightness Contrast Display 1 H Position V Position Hue 2 Color mode Cool Neutral Warm User Clear base Barten Clock phase 1 Clock Phase Saturation 2 Black level Selects VGA Selects DVI Selects S video Selects Composite video Continue to Main Menu Exit OSD Menu in sub menus Exit will move you up in the tree structure Adjust monitor to analog signal from graphics card If you answer YES then you will exit the menu If you answer NO proceed to Clock Phase menu Adjust brightness level See also special note on brightness adjustment in special situations Adjust contrast of the monitor Not active when Clear base Barten color mode has been selected Adju
20. itor is to be placed on a wall or built into a desk then only the LCD panel part is delivered In these cases it is quite often delivered with the plastic housing removed in what is called open frame Certain other options or special mounting components might have been pre installed in contact with electric parts which could cause harm to yourself or your property It should therefore only be handled with special precaution and only by properly trained Warning service personnel When the monitor has been delivered as open frame there is a greater risk to come Power management This unit has power management system The monitor will go into sleep mode where power consumption is less than 5W whenever either horizontal or vertical signals or both disappear High performance panel element The color LCD panel used in this product is specifically designed for advanced applications such as video and marine dimming Protective glass for MAL15776 17776 19776 The marine versions of the product can be fitted with a protective glass for easy cleaning and protecting G version Ergonomic features To ease eyestrain on the user the panel features excellent viewing angles VESA standard wall arm mountings The unit is compliant with VESAs 100mm pitch 75 mm for 15 monitors for hanging tools The panel can be mounted on a wall or arm according to user s environment Safety Precautions This product has been designe
21. ning In case of any abnormality such as odor sound and overheat taking place immediately turn off the power and disconnect the plug from the outlet Continuing to use the unit under such condition may lead to electric shock and or fire For assistance contact your local re seller In the event of thunder immediately turn off the power and disconnect the plug from the outlet Lightning strikes may cause electric shock and or fire In the event of broken panel and leaking liquid crystal do not inhale swallow or touch the liquid crystal It may cause you to get poisoned and or having a skin irritation If you put it in your mouth immediately gargle with water and contact a doctor to get a checkup In case of getting it on your skin and or cloth wipe it off with alcohol and rinse them Safety Precautions Maintenance A Warning A Warning A Caution A Caution Do not remove the plastic cabinet There are high voltage parts inside that may lead to electric shock Ask a re seller for adjustment and inspection Do not remodel or repair It may lead to fire electric shock or injuries inside the unit may lead to fire Ask a re seller for adjustments and inspection Disconnect the plug from the outlet when you do not use the unit for a prolonged period a Clean the dust inside the display once a year The dust that accumulates GD Regulatory reguirements and approvals All produc
22. ns off 2 OSD Control While the monitor is on image on the screen pressing on the Control Dial activates the OSD While the OSD menu is active use the three way movements of the Control Dial to adjust the monitor Rotate Downward Move Up Right Increase Larger More Rotate Upward Move Down Left Decrease Smaller Less Button Press Execute Do Save 3 Change of Brightness Setting If you rotate the Control Dial without first having clicked to enter the OSD then it will change the brightness setting It will do so in a quick way by adjusting with larger steps in the bright area and gradually lower values towards the dark area This is to facility quick change of brightness for marine purpose LED Indicator This LED indicator turns green when the power is switched ON and the power cord is properly attached It turns amber when the monitor goes into a power saving mode Active Off On some models it will be switched off entirely after 10 minutes to avoid that the lamp will distract your vision 14 OSD Adjustment Functions PreVu On Screen Display The LCD monitor features a PreVu On Screen Display OSD menu with easily identifiable icons designed to make adjusting your monitor display settings a more user friendly process When highlighted the icon illustrates the control function and a brief instruction to assist the user in identifying which control needs adjustment The OSD menu is activated by pressing the Contr
23. ol Dial inward and you can select and adjust the function of your choice by rotating and clicking the Control Dial The main menu displays a list of control icons and the current video input mode Rotate the dial to move the highlights to the control you would like to adjust then press the Control Dial inward to select that control or to activate that function Depending on the control you selected a submenu of the control with a status bar will appear The status bar indicates in which direction from the factory preset your adjustments are being made Rotate the Control Dial to adjust the control When you have finished making the adjustments the setting is saved automatically by exiting the control function If you do not touch the control dial for 20 seconds the OSD is automatically exited saving your current settings Menu descriptions The LCD monitor is capable of accepting DVI I VGA DVI I DVI S Video and Composite BNC signal inputs and therefore has three different sets of OSD control functions Depending on your input source and also depending on which color mode you have selected there are some functions that are not necessary cannot be executed or are locked out to comply with certain standards You will then encounter the message Not Available when you try to select such functions The following charts show the function tree and brief explanations of the functions DVI I VGA Auto Setup Auto Setup DVI I DVI Brightness Br
24. omenon that cannot be repaired Non performing pixels Each pixel on the panel actually consists of 3 sub pixels one for each of Red Green and Blue A 19 panel with 1280x1024 therefore has almost 4 million sub pixels It can happen that a pixel can get stuck in ON status bright pixel defect or in OFF status dead pixel defect or in an in between status low bright pixel defect Usually such defects only affect a sub pixel and not an entire pixel The defect can therefore only be seen at certain color settings The ISO 13406 2 standard specifies how many pixel defects that are acceptable before an entire panel will be considered faulty 26 Special Considerations for LCD Panels The products are warranted to follow this Cable length and input signal standard as a Class II product When using long cables from the video source PC camera etc to the monitor the signal level will be lower and cause distortions in the If the same image is shown for a long period of picture shown A low quality graphic board time there is a risk for image sticking This is could also cause such problems Always use a result of that the thin film transistors will get high quality graphic boards and signal cables stuck in a certain position and continue to show that image even when a new image is sent to the panel The image will disappear if you put a full white picture on the monitor for several hours The best solution is to have a s
25. or temperature will gradually go lower so that at full white it could come down to 5000K Typical values In product specifications there are values for brightness contrast view angles etc The values are given as typical values meaning that actual value for any given product can vary by up to 20 from this value For instance a product specified to give 300 candela as typical maximum value for brightness may for individual samples vary from 240 candela to 360 candela The values specified are for a new product Due to wear of the backlight lamps the values will change over time and gradually become lower Uniformity and Mura patterns Depending on the placement of the backlight lamps how many they are and the size of the panel the brightness over the entire panel will vary by up to 20 Generally the highest brightness is in the centre of the panel and becoming gradually lower towards the outer edges This does not follow a linear curve and there might also be areas on the screen where there is a noticeable difference in the uniformity Such clouded areas are referred to as Mura and are more related to the panel itself than to the backlight These Mura patterns are different in size and shape and are color and grayscale dependent since they are a result from deterioration of the liquid crystal alignment layer Mura is most commonly caused by long term operation under high ambient temperature and is a phen
26. ourself or other persons and or un repairable damage to the product or to other attached devices appliances Throughout this manual the following symbols are used to guide you to the proper use of the product Symbols A Person or properties could be at risk of injury or damage Expresses DO NOT severe injury or death Q Expresses MUST DO J Person could be at risk of Warning Keep this Users Manual in an easy accessible and safe place for future reading of it If you lose your copy you may request a new one by contacting us at our internet home page www caspelektronik com We reserves the right to change the specifications of this product without any notice Such changes could cause the operation of the product to be slightly different from the descriptions in this copy of the Users Manual Windows and MS DOS are trademarks and or registered trademarks of Microsoft Corporation in the United States and or other countries VESA is a trademark of the Video Electronics Standard Corporation All other product and company names are trademarks of their respective owners Copyright 2012 Product Features Standard delivery The product is normally delivered in 1 main part e a LCD panel with TFT picture element which also contains the lamps for the backlight along with necessary electronics and cable connectors as well as power connector These parts are mounted inside a plastic housing For marine applications when the mon
27. ranty 19 376 x 301 mm 5 4 300 cd ma typical value 1000 1 typical value 1280x1024 0 8 Mpix 178 178 typical value at CR 10 1 16 2M MVA CCFL Operating Storage 10 40 C 20 60 C 30 75 10 90 700 1060hPa 500 1060hPa 1 DVI I 29 pin connector Compliant with DVI 1 0 2 S video connector Color signal 0 286Vp p 75 O Brightness signal 1Vp p 75 Q 3 BNC connector Composite signal 1Vp p 75 0 4 Audio signal pin jack3 5mm connector 0 2 2 0 Vrms 5 RJ 45 connector Extend interface OSD control 12Vdc 5A Approx 55W Max Less than 4 5W in stand by mode Yes via OSD PreVu Yes 2 pcs ALC Yes software required Add G to type number Optional ELO SAW USB or RS 232 Standard for Marine 0 100 Optional Clearbase Barten UL cUL FCC B CE WEEE RoHS Two 2 years 24 Specifications ML19776 amp 19776G Appearance Net weight Approx 5 7 kg Measurements WxDxH 432 x 65 x 353 mm w o base 2 Mounting Kensington lock Yes prepared VESA standard 100 mm U 432 7 353 467 1 Units with Protective glass MaL19776G or Touch panel are 69 mm deep 25 Specifications Manufacturing of LCD panels is very delicate with large panel elements being manufactured in one unit and then cut to smaller sizes to be used in different products In addition a panel consists of several layers of components back light lamps diffusers electroni
28. rdance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this eguipment does cause unacceptable interference to radio or television reception which can be determined by turning the eguipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult your re seller or an experienced radio TV technician for help FCC Warning To assure continued FCC compliance the user must use a grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores Also any unauthorized changes or modifications to this monitor would void the user s authority to operate this device Warranty and Liability Warranty For details of the warranty please see the separate warranty document included with this product Limitation of Liability Casp Elektronik including any of its affiliates manufacturing partners and sales agents is not liable for any claim for damages including but not limited to loss of business profits disruption of business change or loss of saved data when damage is arising from e fire earthqu
29. rity Lock Slot The LCD monitor is equipped with a security lock slot compatible to Kensington security lock type The security cable lock maybe available thru your dealer or it can be purchased at most computer peripheral stores near you Power management This unit conforms to the DPMS standard Display Power Management Signaling 30 Contact HOW TO CONTACT US Casp Elektronik TIf 45 35263261 Fax 45 35263269 E mail info caspelektronik com WEB www caspelektronik com AUTHORIZED DISTRIBUTOR PC 1 8 2012 Rev 1 31
30. st horizontal screen position Adjust vertical screen position Adjust the hue of the color settings Select a cold color temperature of about 9000K Select a neutral color temperature of about 6500K Select a warm color temperature of about 5500K In a separate sub menu you can set individual values for Red Green and Blue A special color mode intended for viewing of X ray pictures Has a preset greyscale curve in accordance with the DICOM standard Automatically sets the monitor to brightness of about 170 candela and color temperature of about 6500K When set to this mode the OSD functions for Brightness Contrast Black Level are in activated It also locks ALC to ON Fine tune video signal for positioning of the picture horizontally on the screen Adjust Phase frequency to control flickering or horizontal waves on the screen Adjust the saturation of the color settings Adjust the offset level for black color inactive when Clear Base Barten color mode is selected 16 L Charts of OSD Adjustment Functions Main menu continued Management Scaling Scaling of the input signal Full Displays the image on the full screen 1 1 Will display the input without any scaling For instance a resolution of 640x480 will be displayed over the corresponding number of pixels in the center of the screen 4 3 Will scale the picture to 4 3 format 5 4 Will scale the picture to 5 4 format 16 9 Will scale the picture to 16
31. ts have normally been tested to comply with all mandatory Regulatory requirements for the markets where the products are sold Approvals are listed by each Regulatory Agency under the name of the manufacturer and model number as specified on the Product Identification Label Approvals applicable for this product is listed in the Product Specification section of this manual Tests and Approvals for Marine Line Series Each product in the MarineLine series has been tested as an I T category product for normal office environment and for use as a desktop monitor They comply with the following standards and regulations e CE for use within the European Union member states e UL for use in the United States e FCC for use in the United States e WEEE for use within the European Union member states e RoHS for use within the European Union member states Label The below label will be behind the hatch showing approvals and serial number R MAL19746 C 0 l Tn O Fe TE x 74UJ www fineman dk E170908 FCC Information FCC U S Federal Communications Commission This eguipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This eguipment generates uses and can radiate radio freguency energy and if not installed and used in acco
Download Pdf Manuals
Related Search