User manual
Contents
1. VELLEMAN VSCP1 PAN TILT SCANNER CONTROL USER MANUAL MA LEFT i RIGHT PAN TILT SCANNER CONTROL Feature gt Auto on LED Green gt Bypass on LED Red gt Non light during off gt Special screw terminal detachable connector easy for installation Specifications Tilt control Push Button UP DOWN Pan control Push Button LEFT RIGHT Power control Slide Switch MAN OFF AUTO Input Voltage AC 220 230V Output Voltage to Scanner AC 24V Temperature Operating 10 C to 60 C Connector Screw Terminal Detachable Construction Steel Off White Textured Dimensions 212 x 218 x 45mm Weight 1 2Kg VSCP1 VISP1 4 VELLEMAN 1 AC POWER FUSE 2 LEFT 3 RIGHT 4 COM C e OTOTOTo olololo 6 DOWN Operations FRONT PANEL 1 Power Push the rocker switch to AUTO the Green LED will illuminate scanner automatic left and right adjust Push the rocker switch to MAN the Red LED will illuminate scanner adjust by manual Non light during OFF 2 UP AND DOWN Paddle switch UP DOWN 3 LEFT AND RIGHT Paddle switch LEFT RIGHT BACK PANEL 1 AC POWER Terminal block no 1 point 2 LEFT Terminal block no 2 point 3 RIGHT Terminal block no 3 point 4 COM Terminal block no 4 point 5 UP Terminal block no 5 point 6 DOWN Terminal block no 6 point VSCP1 VISP1 5 VELLEMAN2. limit stops see Figure 2 located in each end plate remove two screws securing each end cap to unit Loosen and adjust tilt limit stop screws for desired tilt limit position Tighten limit stop screws and reinstall each end caps to unit and secure with two screws Figure 2 Limit Stop Adjustment and Camera Mounting Plate VSCP1 VISP1 2 VELLEMAN 1 Right Pan Limit Stop 2 Limit Switch Actuator 3 Left Pan Limit Stop 4 Tilt Limit Stop Screw 5 Camera Mounting Plate 6 Screw 7 Down Limit Stop 8 4 conductor cable for video signal 9 Connection to control VSCP71 10 Video Output 5 MAINTENANCE This pan and tilt drive requires no lubrication or maintenance for the life of the unit If the unit fails to function turn it off and check the fuse on the control unit Replacement fuse values are given in the instructions supplied with the control unit 6 SPECIFICATIONS Angular travel Limited Stop Speed Load Rating Duty Cycle Input Voltage Power Consumption Normal Operating Current Cable Requirement Operating Temperature Construction Finish Dimensions Weight VSCP1 VISP1 Pan 350 Tilt 75 Externally adjustable Pan 6 second Tilt 4 second Pan 7 kg Tilt 5 kg Pan continuous Tilt intermittent AC 24V 6W 24V 200mMA Six conductor unshielded 5 C to 60 C Aluminium and plastic Off white baked enamel finish 150 x 160 x 200mm 2 3 kg 3
3. VISP 1 PAN TILT UNIT Velleman USER MANUAL 1 INSTALLATION The unit is intended to be mounted on a Wall Mount Installation of the pan and tilt drive to the wall mount requires a stainless steel 1 4 20 screw supplied with the wall mount Note the ribs on the underside of the unit base engage slots in the mount This allows positioning of the unit in any of four directions with respect to the wall mount Secure unit to the wall mount using screw from underside of wall mount into unit and tighten 2 WIRING OF UNIT Fabricate the interconnecting cable in accordance with Figure 1 for proper operation POWER red COMMON black TILT DOWN yellow TILT UP blue PAN RIGHT green PAN LEFT white QO aoa WAN Figure 1 Cable Assembly Diagram 3 INVERTED MOUNTING When the unit is mounted in the inverted position the left right directions are reversed for manual operation This must be corrected when wiring the cable between control unit and the pan and tilt drive Simply reverse leads going to terminals 3 and 4 4 ADJUSTING LIMIT STOPS After cable is installed and unit has been mounted proceed as follow 1 Plug control unit into AC 24V source Be sure auto switch is in the OFF position VSCP1 VISP1 1 VELLEMAN 2 To adjust pan limit stops see Figure 2 loosen screws securing both stops 1 and 3 to unit Slide stops around unit to desired locations and secure by tightening screws 3 To adjust tilt
Download Pdf Manuals
Related Search