Home

Autonics KRN100 Recorder Manual PDF

Contents

1. 7th Check recording paper operates normally by pressing front key with FEED FEED function in stop recording state Copyright Reserved Autonics Co Ltd 147 i 10 Maintenance Autonics 148 O Copyright Reserved Autonics Co Ltd Autonics 11 Troubleshooting i 11 Troubleshooting Check KRN 100 normal operation regularly Troubleshooting When power ON KRN100 does not display Check power supply and power connector is anything on LCD screen and operate connected normally KRN100 has date and time error within Displayed date and time is not correct 2min year Useable until in 2100 Set date and time again Check sensor input settings are correct in INPUT SETUP Sensor input value is not right Turn OFF the power of KRN100 and remove input cards from KRN100 and check jumper pin settings according to input specification Displaying record memory status icon op or E is the state of recording former digital data _ Because there are lots of alarms and record KRN100 records former digital data not events or recorded data is accumulated due to current time s short memo period To cancel former data recording pause and re start record Change the settings about record for proper operation In graph mode printout for line and letters is Replace ink cartridge not clear and spread Recording pa
2. Ink cartridge Record ink cartridge to record data on recording paper Model name D33006B 66X 01 Q Recording paper cassette Cassette saves the recording paper 3 Recording paper cassette lever Press the lever down and this recording paper cassette is removed from KRN100 Remove the recording paper cassette for recording paper replacement ink cartridge replacement 1 4 4 Paper cassette Recording paper holder Movement holder of recording paper when recording Recording paper storage part Storage part for recorded recording paper Front cover of recording paper storage Open recording paper guide for recording paper replacement New recording paper storage Storage part for new recording paper 1EA recording paper is storable 086 Back cover of recording paper storage 20 Copyright Reserved Autonics Co Ltd Autonics 2 Specification 2 Specification 2 1 KRN100 Screen Adjusting 4 level OFF Min Standard Max brightness Backlight White LED 2 level Temp Always The number of input 2 4 6 8 10 12 channel 2 channel card Expandable channe Universal input Temperature sensor RTD thermocouple analog 1 to 4 channel 25 ms 125 ms 250 ms 5 to 12 channel 125 ms 250 ms Inner sampling period is operation unit time for average movement filter Sampling period and alarm output function X Max sampling period for TC R U S and T s
3. 2 NNN IT 2nd Push down recording paper cassette lever placed at below recording paper cassette recording paper cassette is removed from KRN 100 O Copyright Reserved Autonics Co Ltd 143 10 Maintenance Autonics 3rd Pull out ink cartridge and it is removed from KRN 100 Insert new ink cartridge Fr E f Oo D Recording paper replacement 10 2 this Below figure is detached recording paper cassette WAN T
4. I P Ist From 1st to 2nd steps are same as Ink cartridge replacement method Please refer to 2nd Open new recording paper storage cover and finished recording paper storage cover of recording paper cassette 144 Copyright Reserved Autonics Co Ltd Autonics 10 Maintenance 3rd For better print recording paper should be loosen by entering the air If not as below figure it may cause paper jam 4th Remove finished recording paper in finished recording paper storage and replace ne recording paper New recording Finished paper recording paper Copyright Reserved Autonics Co Ltd 145 10 Maintenance Autonics 5th Put recording paper s holes circle oval at recording paper holder and close new recording paper storage cover and finished recording paper storage cover Cycle hole O O Oval hole O O 146 Copyright Reserved Autonics Co Ltd Autonics 10 Maintenance i 6th Push recording paper cartridge into KRN100 until click sound Close front cover of KRN100 WN Ea
5. rarrrrnnrrrrnnrerrnnnrrrnnnrnrnnnennnnrnnnnnennnnne 116 8 6 11 Log Speed Save period LR 117 8 6 12 Backlight LCD backlight brightness rrrrnnrrrrnnrrrrnnrrnrannernnnrnrnanrnnnnne 117 8 6 13 Backlight On Off LCD backlight ON method 117 8 7 FILE MEMORY SETUP File Memory setting 118 8 7 1 Load Set File Open parameter setting file 119 8 7 2 Save Set File Save parameter setting file 119 8 7 3 Memory Status Memory capacity 120 8 7 4 Memory Clear Delete memory 120 Copyright Reserved Autonics Co Ltd xi li Table of Contents Autonics 8 7 5 USB LogData Save USB storage function 121 8 7 6 Memory Save Option Memory storage option 122 8 7 7 USB Memory Copy Move Move Copy data 123 8 8 USER INFORMATION SETUP User information setting 124 8 8 1 Password Password mode 125 8 8 2 Login Admin Administrator log in 126 8 8 3 Change Admin Password Change password by administrator 126 8 8 4 User Lock Change user authority orrrrrnnnrrnnnnrrnnnrrrnnrrrrnnnrnrnnrnnnnnnennnn 127 8 8 5 Information Check system information arrrrnrnnnrrnrnnnrrrrnnnnrrnnnnnrennnnnre 127 8 8 6 Firmware Upgrade Firmware upgrade 128 8 9 RECORD BACKUP _ SETUP Backup data record setting 130 8 9 1 Record Backup Back
6. Set range Graph Digital Factory default Graph 98 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 5 2 Digital Print type 1 line record channel during numeric recording OEM RECORD SETUP FI NAME gt VALUE gt Record Mode Graph Digital Print Type standard Speed 2 enn h Option Speed 2 Am h Hemo Period 1hour Pl 1 tri Eat af Designate the number of channels to be printed when recording display value on recording paper It prints channel information between Graph and Digital record mode Set range OneCH TwoCH Factory default TwoCH 1 TwoCH It records 2 channels in one line and records occurring alarm as abbreviation In case of multi alarms it records as AL Print form is as below DATE Tag Name PV Unit Unit PV Unit TIME CORRE DEEE eh CEE EE SP CP ON SEE LE LEE ED LL kL LEE O CH H 129 52 151 ECH BE 208 82 Fot iP O CH 3 320 2 fC PLICH 4 512 6 ic i bi 11 106 16 OilcH 5 5452 45 Ci ii iCH 65 825 0 ci AL 11 DO 00 CUPP nr on nn nnnnnunss e p TS EN ES ss any Alarm Error Alarm Error 2 OneCH It records 2 channels in one line and records occurring alarm as abbreviation Not as TwoCH it also records one channel s error message and occurring alarms in 4 alarms Print form is as below DATE Tag Name PV Unit Error Alarmi Alarm2 Alarm3 Alarm4 TIME OcH 1 125 5 i6 IL
7. Set range Overwrite Stop Factory default Stop 122 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 7 7 USB Memory Copy Move Move Copy data je LP Sp 23456 OSM fee lon 15 58 08 USB Move Cop Hone Moves copies or deletes the saved backup data on inner Memory to an USB memory Currently saving backup data has mark and it is not able to copy move and delete Copy to USB Saves selected backup data to an USB memory and preserves backup Memory data of system memory Move to USB Saves selected backup data to an USB memory and deletes backup data Memory of system memory Delete File Deletes backup data Displays backup data information Displayed information is Name Path Size Log Channel Log Speed Set range For the desired file Copy to USB Memory Move to USB Memory Delete File File Information Factory default USB Copy Move Copy Move to USB Memory el Pm ON 234567 AS OA MORE ml Ta an S456 ete ra sl ey USB Hove Copy None fl USB Move Lopy lt Internal 6 LR eg Internal 142 USE Memory Gy 141 KARN AR 241141311569 Move to USB Memory KBRNTAR 28118131 185449 FENIOG_ 24101230 115322 CRRA Delete File KRNTAR 28181238 115434 KRMNIAA 2AT1A131 179 File Infomation OPA KANT Be 26181229 155662 KRH AR 20101229 135415 KRNTAA 2A1 18131 171982 KANTEB 28181229 134222 he LA LE F F LL Into Directory St 2011 81 31 ET mld mn SENS Lie Tasse rise A
8. 69 8 1 18 Filter Counter The number of digital filter rorrrrnrernnrrrnnrrrarrrrarernnnennn 70 8 1 19 Burnout Action Display setting for break 71 8 2 ALARM SETUP Alarm setting 72 8 2 1 Select Ul Card Select universal card input rrronrrrrnnnrrrannrnnannrrnnnennnnrr 73 8 2 2 Alarm Set Copy Copy alarm parameter 73 8 2 3 Alarm Type Alarm operation mode 74 8 2 4 Alarm Ref Channel Alarm reference channel 76 8 2 5 Alarm Option Alarm option ss 17 8 2 6 Alarm Value Alarm set value rrrrannrrnrnnnnrnrnnnnrrnnnnnnrennnnnnrnnnnnnnnnnnnnnen 78 8 2 7 Alarm Hysteresis Alarm hysteresis 79 8 2 8 Alarm ON OFF Delay Alarm ON OFF output delay time 80 8 2 9 Alarm Alarm No Alarm output alarm number 81 8 2 10 Select Alarm Card Select alarm output card 81 8 2 11 Alarm Status Relay and transistor output method 82 8 3 DIGITAL INPUT SETUP Digital input setting 83 8 3 1 Select DI Card Select digital input Card rrrronrrnrnnnrnrnnnrrnnnrrnnnnrnvnnnennnn 84 8 3 2 DI Type Select digital input eecccceececeeeeeeseeeeseeeeesaeeeeeees 85 8 3 3 DI Reset No Reset alarm number 86 8 3 4 DI Status Operation status 86 8 4 COMMUNICATION SETUP Communication Setting rrrrrnnnrrrrrnnrrenrnnnnnnn 87 8 4 1 Modbus Address Communication address 90 8 4 2 R548
9. ALARM SETUP ALARM OUTPUT STATUS SETUP DIGITAL INPUT SETUP COMMUNICATION SETUP RECORD SETUP i SYSTEM SETUP FILE MEMORY SETUP USER INFORMATION SETUP Et User Memory Record Backup LogData Download al User Unit Logo Image User Unit Logo Image Dowr 9 3 1 Record Backup You can download backup data which is saved in KRN 100 inner memory from Record Backup section Directory form is year month day Click the relevant icon and check below list To download backup file click the file name with right mouse button and select Download Log File menu KRN100 Record Memory Data Name Size The Numb Start Time SL 2012 CA 4 Gia 3 Ca 29 Ly 28 Ga 12 Ca 9 Lg 7 KRN100_20120307 ES ae vpn 24 844 2012 03 08 13 53 44 2012 03 08 14 07 39 LI 6 Ca 2 1 Ca 2011 Download Folder Je Cancel Backup files are strucured as tree type directory at KRN100 inner memory You can easily fine and download the desired file Copyright Reserved Autonics Co Ltd 137 i 9 DAQMaster Autonics E Note When checking backup data by DAQMaster it may not be same as origital print out 100 Therefore please use backup data as reference 9 3 2 User unit setting Total 3 sizes user units are needed two for display output one for printing Image type Size Unit image for printing 32X10 Small unit Unit image in several channel for displaying 32X12 Middle unit Unit image in 1 channel for displ
10. Autonics 8 Parameter detail setup 8 5 6 Divide Zone Record zone division OEM RECORD SETUP FI NAME gt Digital Print Tyre Standard Speed Option Speed Memo Period Divide one Divides record zone for measuring value by channel It divides equally max 12 zones as equal value User needs to set record zone by channel in Record Zone setting at Input Setup It is easy to check measuring value due not to duplicated record zone with divided record zone by channel which is set in Record Zone setting at Input Setup If there is too many division for record zone record value check accuracy is low Set range None 2 to 12 Factory default None Set value of record zone division None 000000 0000000 Set value of record zone division 5 O O 0O O 0000000 20mm 20mm 20mm 20mm 20mm Copyright Reserved Autonics Co Ltd 103 I 8 Parameter detail setup Autonics 8 5 7 Standard Period Standard record period AE E B k LS m0 9 23456789 N E ru es 55 sa a RECORD SETUP RECORD SETUP MANE E Memo Period Standard Period Divide Zone standard Period Amis Period Ein as Option Period rego a Listing Language English rh muuu Set record period to record current time display value by channel as digital number on recording paper It is actiaved when Record Mode Record mode is Digital Set range 00m 01s to 99m 59s Depending on the number of recordin
11. Alarm Value alarmL SV Response Wait Time com response waiting time Alarm Hysteresis alarm hysteresis Input Type input specifications OK Alarm ON OFF Delay Range Scale Point alarm output ON OFF Protocol Cancel decimal point com protocol delay time Rem e ee eee ee ee ee ee 8 i Alarm Alarm No i alarm output alarm i number RS485 Com Write Display Temp Unit RS485 com write display temp unit High Low Range Selection Alarm Card amp Graph Scale Alarm output card high low input value i ae Seah Scale select Low Scale Alarm Status l High Scale relay and transistor high low scale value output method Ethernet Port Ethernet com use IP Address IP address Subnet Mask subnet mask Special Func special function Two Unit i display vacuum static pressure Default Gateway default gateway Ethernet Com Write Ethernet com write USB Device Port USB com use Input Bias error correction USB Com Write USB com write Span gradient adjustment Record Method data storage method Filter Type input digital filter Filter Counter number of digital filters eee ee eee ee ee ee ee dJ Burnout Action display setting for break 50 Copyright Reserved Autonics Co Ltd Autonics 7 Operation FILE MEMORY RECORD SETUP SYSTEM SETUP erd record setting
12. VALUE Alarm Set Copy Alarm Tyee Alarmi Ret CH Hlarmi Option n Alarm Set Copy I CHS S2UT 1 Hlarmi Tyee CH4 S2UT 2 Alarm Ref CH CH5 SSUI 1 Alarm Option CHE SSUI 2 i N LIFT Gi l You do not need to set same parameter settings repeatedly for other channels This function is to copy set value of alarm parameter of the set channel and applys it to other channels Copiable parameters are as below Alarm Type AlarmL operation mode Alarm Value AlarmL Set value Alarm OFF Delay AlarmL OFF delay time Alarm _ Ref Channel AlarmL reference channel Alarm Option AlarmL option Alarm Hysteresis Alarm ON Delay Alarm 1 hysteresis AlarmL ON delay time Alarm Alarm No Alarm output relay number Set range No Select CH 1 S 1UI Activated connected universal input 2 channels per input card Factory default CH Select Copyright Reserved Autonics Co Ltd 73 I 8 Parameter detail setup Autonics 8 2 3 74 Alarm Set Copy AlarmL Type AlarmL operation mode ro TA 128 ALARM SETUP rs NAME gt select UT Card CH1 S1UI 1 VALUE CH1 S1UI 1 CH Select Alarm Tyre Alarmi Ref CH Alarmi Option LL Li No alarm Noam Absolute value upper limit alarm Absolute value lower limit alarm Deviation upper limit alarm Deviation lower limit alarm No recording paper alarm Hone did 1 Designate alarm operat
13. 2 Single Single ON OFF Starts recording at the start set time on start date and finishes recording at the end set time on end date Reservation Period reservation record period Start Date 2011 1 1 End Date 2011 1 5 Reservation Time reservation record time Start Time 12 00 00 End Time 23 59 59 12h00m00s 23h59m59s y y Time 2011y0im01d 2011y01m02d 2011y0im03d 2011y01im04d 2011y01m05d It starts recording at 12 00 00 on January 1 2011 and finishes it at 23 59 59 January 5 2011 114 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 6 7 Reservation Period Reservation record period OM Pi 23456 7890 lues 22rastad fele Ga Sp 23 45678902 N lues oo as 1 STSlEM SETUP a atslEN SETUP le NAME gt VALUE summer Time Period HSmsid Heh AYnkld BR giPeservation Reservation Tyre Repeat AAR 14 1 Reservation Period zada 11 07 Reservation Time AAhAANAksS AAKAANAAS Alarm sound OFF Designate reservation record period When Reservation Type Reservation record is set as Repeat Repeat ON OFF or Single Single ON OFF it is activated to designate Start Date Start date and End Date End date Set range 2000 01 01 to 2099 12 31 Factory default 8 6 8 Reservation Time Reservation record time el PS 23456 7890 wes BE here Ma dn2345678 90 El lue BE STSlEM SETUP En atslEN SETUP ai H ME gt VALUE gt MiPaservation summer Time Period AAm
14. E Note Supporting file system is FAT16 FAT32 when using an USB memory Microsoft s file system NTFS and Linux s file system EXT2 EXT3 etc are not supportable A Caution When connecting an USB memory KRN100 pauses backup data download by Modbus function and backup data printer function to recognize memory for a while dending on the capacity max 30 sec lf an USB memory s LED flashes do not remove an USB memory or it may damage to the data If the damage of USBmemory data occurs you can find the saved data from KRN100 inner memory and save the desired file to an USB memory Set USB LogData Save USB storage function as Disable and when the below message disappears remove an USB memory OA LEONE AE HE TRE Plase Wait USB LogData Saye ef ete CHIZ Copyright Reserved Autonics Co Ltd 121 I 8 Parameter detail setup Autonics 8 7 6 Memory Save Option Memory storage option je fm Sj ASETE NASE Seb 23447 17 FILEN SETU save set File Memory Status Memory Clear USB Loalata Save Memory Save Option Set the operation how to storage new data when inner memory storage space is used all as 100 Genie Deletes the oldest backup data file in order and saves new data Important backup data should be backup at first Stops backup data Stop Stop saving It does not save Backup data Even though new recording paper is replaced output function for backup data does not operate
15. N O 0NC 72 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup x 1 Alarm Type to Alarm Alarm No parameters are displayed as the number of connected alarm output card XShaded parameters are affected by set value of other parameters Please refer to specific descriptions of each parameter 8 2 1 Select Ul Card Select universal card input fel ton 61 23456789 002 lese ru iraa Ped Po 23456789 ONAN ri 15 42 29 ALARM SETUP CHI S1UI 1 a Eras CH1 S1UI 1 CHI SIUI 1 E lt HAME gt VALUE gt lt NAME gt YALU CH2 S1UT 2 select UI Card CHi S1UT 1 select UI Card Ry CH3 S2U Alarm Set Copy CH Select Alarm Set Copy CHd S2UI Alarm Type FY Hi Alarm Type CH5 S3U1 1 Alarmi Ret CH Alarmi Ret CH CHB S3U1 2 Alarmi Option Alarmi Option CH S4UI 1 Select the channel of universal input card KRN UI2 to be set One universal input card has two channels KRN100 automatically searches connected input output card on slot power when power ON and recognizes the number of universal input card KRN UI2 Set range CHI J S 1UI J Activated connected universal input 2 channels per input card Factory default Automatically set 8 2 2 Alarm Set Copy Copy alarm parameter mr de SN 23456789 014 en 12910800 ALARH SETUP CHI SIUI 1 No Select A NAME gt VALU CHI S1UI 1 select UI Card CH CHP S1UT 2 mn T 23456 76901 rm rue 1 28 66 ALARM SETUP NAME gt select Ul Card CH1 S1UI 1
16. OFS SF MARS OR a V SAM PEAS sanere vi FETE sei ee ee eee ee eee ee Ix 1 OVNI MN 13 1 1 FUENTE 13 L2 Component and sold separately 14 k21 01191 812 0 6 ne 14 VANN 14 1 3 Ordering MOTE ae eee eee 15 1 4 Prepp 17 1 4 1 Front and side part 17 14 2 PE S 19 Ne BMV VS EEE de me 20 1 4 4 Paper cassette rarrrnnnrrnnnrnnnnvrnanrrnnnrnnnnrvnnrnnanrnnanrnnnnnnnnnnnannnnanennnnrnnnnennnnen 20 2 SpecificatiON ES de aan e nan ane ed nach cs 21 2 1 KRD 44454444 21 22 HO 0 A A RE E EE E E EEEE EEEE E 23 2 3 Input specification and measuring range 25 MOTS OS a eee ea ee one ea se ne 27 ce 28 4 1 FRU aan a 28 4 2 AS Ke 0 EEE 29 5 Installation rxenrnnnnnnnennvnnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnunne 31 5 1 Installation place iii 31 2 SOA nee NR NE 32 9 2 Bracket NON eee 32 5 2 2 Additional I O card connection 33 5 3 USB 10 Serial driver ssa E A EES ESS SE Sri asi 34 5 3 1 Driver installation 34 5 3 2 Checking driver 5 555 Soe Gensdaieawie sisenann dad ened sion bee skanne hidden died 36 be 37 6 1 initial DOCS CR nt AAEN 37 6 2 SN OU ee 38 EE 10005 0 EE de ot ea 38 6 2 2 Virtual keyboard oie sccasinncedessnascesseceves naanin ina aaa aina ia 41 6 2 3 Parameter setting display 42 TONN 43 Copyright Reserved Autonics Co Ltd IX li Table of Contents Autonics 7 1 Se 0 0 6 sa EE eee eee 44 7 1 1 Measuri
17. C but display temprature from recorder is 78 C set Input Bias Error correction as 2 and display temperature is 80 C Copyright Reserved Autonics Co Ltd 67 I 8 Parameter detail setup Autonics 8 1 15 Span Gradient adjustment el M ON 23 45678900 ee re EE enl M OM 23456789 10244 ee INPUT SETUP IEEE i TIS EE maleic ojelFi als E Special Function Two Unit med I IKILININ l415 6 We Cote ANS Clee pg o r aln sjrjuf 17 e al Pet Channel i Input Bias ae ey wi xy Z seace f aol nes SE em ge This menu is for adjusting upper limit error by regulating display value which is about measuring value or applied scale In case Low Scale Lower limit scale value and High Scale Upper limit scale value are fixed and Span Gradient adjustment is only set When Input range is 0 10V Low Scale Lower limit scale value is 0 00 and High Scale Upper limit scale value is 10 00 If changing gradient adjustment value as 0 500 1 000 or 1 500 display value by each changed gradient adjustment value is below Same 0 00 1000 0500 0 00t05 00 result 000 11000 1000 000 1000 1500 oo woo 1000 1000 oo 15 00 1000 Display Gradient value adjustment value In case Low Scale Lower limit scale value and High Upper limit scalevalue are fixed and Span Gradient adjustment is only set reverse gradient When Input range is 0 10V Low Scale Lower limit scale value is 10 00 Hi
18. DAQMaster menu click Tool Data Anal Programs gt Documents fey DataAnal Settings emer een 8 H El E Readme Search gt Uninstall mn Website Help and Support Run m Log Off Autonics En E Turn Off Computer E Eu E MIE Look in B Desktop v fn CE my Documents 4 My Computer omy Network Places L KRN100 USB Serial Drivers r E KRN100_20120413_134210 Places My Network File name arType Unit Descriptio Files of type RN100 Record Data Fi ef arc Cancel 140 Copyright Reserved Autonics Co Ltd Autonics 9 DAQMaster i 3rd Open chart and drag the desired channel to check waveforms or values EI Data Anal gt DAQ apace Z Data Graph ust DekteAl Delete Ch Col File Name Tag Name KRN100 20120 CH 1 KRN100 20120 CH 2 For more information please refer to DAQMaster user manual Note When checking backup data by DAQMaster it may not be 100 same with original print out Please use backup data only for reference Copyright Reserved Autonics Co Ltd 141 9 DAQMaster Autonics 142 O Copyright Reserved Autonics Co Ltd Autonics 10 Maintenance i 10 Maintenance 10 1 Ink cartridge replacement Ist Press MN key for 3 sec in stop recording state and Ink cartridge moves to the center to be replaced easily Open front cover of KRN 100
19. Factory default Disable G Note Password mode setting Disable Enable is available without authority But Enable Disable changing is only available by administrator s authority Enter the set password at Login Admin to change the mode In administrator lock state when power turns OFF ON it changes user lock mode Copyright Reserved Autonics Co Ltd 125 I 8 Parameter detail setup Autonics 8 8 2 Login Admin Administrator log in aa Yon 23456789 OAM ed 23 48 27 USERINFORMATION SETUP User ode NAME gt Password Login Admin eC Change Admin Password User Lock OFF Information Display LET Eu 15 F Ris US Log in to the parameter by entering password as administrator Set range 4 digit number Factory default VG Note When password is not set yet default password is 0000 When entered administrator s password is wrong it displays Fail ASKey xxxx Please call our service center 82 32 820 2343 and tell us ASKey and you can check administrator s password ml in 23456789 nen U amp ERINFORMATTON SETUP User Model te NAME gt Passwor Login Admi Change Admin Password User Lock Information 8 8 3 Change Admin Password Change password by ai aaie Pin 23456789 0 lies zsassaa me Po M2456 789 MSIE mon i7iaies USERINFORMAT ION SE TUP icin oder ajae e ole e BEJ Password Enable mee rf sfkfilnln fals ej eres Adnin Per a mole tatals riul 7 el al Us
20. Termination Set Response Wait Time To prevent possible error due to communicating with low speed Master PC PLC etc set communication response wait time If you set too short communication response wait time communication error may occur in Master Set range 5 to 99 unit ms Factory default 20ms 8 4 8 Protocol Communication protocol url po ERE uer COMMUNICATION SETUP FA NAME gt VALUE Parity Bit Hone stop Bit Termination Set Disable Response Vait Time eM ms Protocol Modbus ATU It supports Modbus RTU Remote Terminal Uint as communication protocol Data Length 8bit Data interval 24bits or less Error Detection CRC 16 Set range Modbus RTU Factory default Modbus RTU 8 4 9 RS485 Com Write RS485 communication write OKETA ned 22 54 50 a COMMUNICATION SETUP MAME gt Stor Bit Termination Set Response Wait Time ms Protocol Modbus ATU R5485 Com Write man Eo oF EE miia Set whether changing the set value of KRN100 parameter by R8485 communication To read the set value of each parameter is available regardless of the communication write enable disable setting Set range Enable Disable Factory default Enable 92 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup i 8 4 10 Ethernet Port Use Ethernet communication fe rm 023456 ASMA med 22 54 43 a COMMUNICATION SETUP lt H AHE Termination Set Response Wait
21. USERINFORMATION SETUP Password Disable MAME gt VALUE User Lock Password isable Login Admin Change Admin Password Information Display Set range Factory default Disable Enable 0000 to 9999 OFF LOCK1 LOCK2 LOCK3 Display Automatically display Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 8 1 Password Password mode fe RENE AE EE USERINFORMATION SETUP Password Disable a NAME gt VELLE Password Login Admin Change Admin Password User Lock Information Display LE Eu in fon R Ris US You can set password and the mode as user general user mode and administrator mode to restrict parameter setting and record function Administrator has every operate authority and user general user has only administrator defined authority Description Allows every user operation authorization to use all functions With administrator s or user s log in and password allows operation authorization Disable Enable Password Available Disable every function User Available Mode every function When setting the password lock icon is displayed In user general user mode lock icon marks as f and in administrator mode it marks as A Enable USERINFORMATION SETUP Admin Mode lt NAME gt lt VALUE gt Password Login Admin Change Admin Password User Lock Information Display Set range Disable Enable
22. i i ENTER ENTER ENTER ENTER ENTER Record Mode Device Name amar il Password Record Backup record mode device name P file open g password mode backup data record Digital Print type Save Set File 1 line record CH during acne parameter setting numeric recording file save Standard Speed standard record speed Login Admin Backup Data List admin log in backup data list een m Start Date and Time password change by admin start time for data save User Lock user authority change End Date and Time end time for data save Option Speed option record speed Memo Period Summer Time Period digital memo cycle summer time period Backup Print Mode backup data print system info check mode Information Selection Print Mode backup data recording mode setting Divide Zone Reservation Type Firmware Upgrade record zone division reservation record firmware upgrade Standard Period Reservation Period i USB Memory standard record reservation record Copy Move i i period data move copy Option Period peservalion TIME reservation record i option record cycle Listing Language language for list oa eeu printing alarm sound Sampling Rate sampling cycle Power On Status rer record status when g SP power ON save cycle Run Status Backlight list printing at start LCD backlight recording brightness
23. 4th Set KRN100 Ethernet Port Use Ethernet communication as Enable at COMMUNICATION SETUP Communication setting of KRN100 Set IP Address IP address as installation environment le dio 9123456 789 0 eA MED 22 54 91 E COMMUNICATION SETUP NAME gt VALUE Response Wait Time eH MS Protocal Modbus ATU Aedes Com Write Enable Ethernet Port Disable IP Address 197 168 1 2 IP address set for Modbus TCP communication is complete 94 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup i 8 4 11 IP Address IP address le Mo 512345689018 lues San Le Pin 623456789018 6 med 22 34 56 a COMMUNICATION SETUP DR COMMUNICATION SETUP NAME gt VALUE gt Response Wait Time cH ms Protocol Modbus ATU IF Address EA 168 1 Asde5 Com Write Enable HetMask SER 955 255 Ethernet Port Disable Gatellas 192 165 1 IP Address Designate used IP address to identify the device on the network If there is same IP address on the network communication does not operate by IP conflict Set range 0 0 0 0 to 255 255 255 255 Factory default 8 4 12 Subnet Mask Subnet Mask me Pm OM 23456 TOI med 22550 ele oO 234567690128 mon 14 50 2a a a COMMUNICATION SETUP lt HAME gt VALUE Protocol Modbus ATU IF Address 197 168 i HS485 Com Write Subnet Mask BA 255 255 F Ethernet Port IP Address BE 1 Default GateWay 192 160 1 subnet Mask 200 205 295 A LF HUUT E
24. 51 58 a L DIGITALIHFUT SETUP S80 NAME gt select OF Card OI 1 Tyre Ruri UI 1 Reset Ho OI 1 Status Ol 2 Type Hone Designate operation status of set digital input Ed When digital input is input over 0 3 sec the set function operates If digital input is re ge input the reverse function operates ava When digital input is short over 0 3 sec the set function operates If digital input is eve open over 0 3 sec the operation is stop Set range Edge Level Please refer to 8 3 2 DI L Type Select digital input J Factory default Note In digital input setting when DI L Type is set as Run or Seed and DI Status is set as Edge overlap setting is available But DI L Status is set as Level overlap setting is not available If even one Level is set DI L Status s overlap setting to Level or setting to Edge is not available In case DI L Status operation status is Edge You can execute to start stop recording with front key In case DI L Status operation status is Level You cannot execute to start stop recording with front key 86 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 4 COMMUNICATION SETUP Communication setting Set the related parameters with communication output card KRN COM You can only check the item of COMMUNICATION SETUP by communication but cannot change the set This parameter is for setting and monitoring param
25. A value Display Display value Ta o B value g f S y Input Input value value Y Ban value You can change display value about min max input value of measuring value In case input specification is 0 to 20mA Set Low Scale Lower limit scale value 0 0 High Scale Upper limit scale value 10 0 20 0 30 0 20 0 Display value Input LE Fe 20mA value 20 0 V Set Low Scale Lower limit scale value 20 0 High Scale Upper limit scale value 20 0 Display value 20 0 He auke dt finere Input a 20mA value 20 0 242 Copyright Reserved Autonics Co Ltd 61 i 8 Parameter detail setup Autonics Set Low Scale Lower limit scale value 20 0 High Scale Upper limit scale value 20 0 Display value Input value 1 Low ser limit scale value mrd Em 623845676900 lues cie Lee ke Oil 23456 78904 oe m ruil io 1216 aae Si mje elc ole ro els peme EEE special Function Two Unit a vf wi x Zz Space fol EC CE Reference Channel Set scale value for lower limit input value Low Range e Set range 99999 to 99999 9999 9 to 9999 9 999 99 to 999 99 99 999 to 99 999 9 9999 to 9 9999 Depending on Scale Point setting the range is different e Factory default 2 High Scale Upper limit scale value re PP ON S456 789 0 Lee am bn ON 23456 789 00 on 1 108 INPUT SETUP CHA SSUT 1 i
26. BURN BURN 42 3 36 4 45 4 Digital number 12 channels displays all channels 1 to 12 channel It does not support auto manual channel switch function 7 1 2 2 Auto channel switch mode Manual channel switch mode Ist When supplying re supplying power to KRN100 it is display currently display and auto channel switch mode 2nd If you want to change manual channel switch mode press KM key or WM key LIST AL RESET J 3rd You can switch select the to be displayed channel by pressing key or key 4th In manual channel switch mode press key to change to auto channel switch mode Copyright Reserved Autonics Co Ltd 47 i 7 Operation Autonics 1 2 Special operation for record KRN100 executes special operation for record with front keys EZ Es D EE 1 Start record RUN Stop record STOP Press front M key at once it starts recording and press this key once again it stops recording When digital input operation status is set as Level you cannot start stop record by front MUM key In case of as Edge start record RUN stop record STOP function is available with front M key 2 Parameter s set information print List Print This function is to record the main parameter s set information on recording paper Press key for over 3 sec during recording or stop state and it records the set information of each menu For more information please refer to 8 5 13 List Out Optio
27. Baklight On Off LCD backlight ON method List Out Option list record option Zone Dot Line Distance dot line for zone division CH Print Distance record interval for each channel graph Start Line Print start line when starting record Range Print Time input range record period Copyright Reserved Autonics Co Ltd 51 i 7 Operation Autonics 52 Copyright Reserved Autonics Co Ltd irame Autonics 8 Pa qAatail catiin Parameter detail setup INPUT SETUP Input setting You can set details for input specification and scale by universal input channel record method input digital filter input error correction etc Move to INPUT SETUP with DISPLAY im 1234587330 Fa ey Ju INPUT me ALARH SETUP DIGITAL INPUT SETUP COMMUNICATION SETUP RECORD SETUP StoTEM SETUP FILE MEMORY SETUP E Aes al Parameter list 0 4 C ME 3 PC 1 6 C 1 QC mn Keys press key to enter INPUT SETUP me mb 23456 TAS wed 2a 27 20 a INPUT SETUP CH3 S2U 1 2811 96 15 ED 26 24 46 select UI Card Input Set Copy LOO Parer Record Pen Color Record one Factory Select Ul Card Select universal input Automatica Input Set Copy Copy input parameter None CHO SHUHO CH Select LCD Paper Record Display and record Pen Color Record color 1 Violet 2 Red 3 Black 4 Green 5 Blue lt 6 Brown Automatica lly set Tag Tag Name Channel name Tag N
28. Designate one record operation stauts from 3 mode for when KRN100 re turns ON from OFF by power failure Hold Maintain Maintains record status of before power OFF recording or stop recording Run Record Operates recording when power is ON Stop Stop recording No recording when power is ON Set range Hold Run Stop Factory default Hold 106 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 5 12 Run Status List printing at start recording fr Sp 23456789 mit Aee lue SE RECORD SETUP P lt HEME gt VALUE gt Option Period Listing Language English Alarm Speed 2 Arnim h Power On status Hold Run Status oto Set wheter to print setting list when starting recording When printing list icon for record in section 1 is changed as C2 and flashes After printing list with 240mm h record speed it processes record with changed set record speed Please refer to List Out Option List record option for the set list item Set range ON OFF Factory default OFF Copyright Reserved Autonics Co Ltd 107 I 8 Parameter detail setup Autonics 8 5 13 List Out Option List record option mle Fi S1234567890NAAEN web 22 06 55 RECORD SETUP ke NAME gt Alarm Speed Power On status Aun status List Out Option Dot Line Distance H Dein EE tate Select parameter set value recording either Standard or Option and it starts record It is activated when Run S
29. Dimensions or specifications on this catalogue may be changed without prior notice www autonics com Headquarters 116 Ungbigongdan gil Yangsan si Gyeongsangnam do Korea el Overseas Sales Dept 402 404 Bucheon Techno Park 655 Pyeongcheon ro Wonmi gu Bucheon Gyeonggi do Korea Tel 82 32 610 2730 Fax 82 32 329 0728 E mail sales autonics com WE Brazil Autonics do Brasil Comercial Importadora Exportadora Ltda Tel 55 11 2307 8480 Fax 55 11 2309 7784 E mail vendas autonics com br China Autonics electronic Jiaxing Corporation Tel 86 573 8216 1900 Fax 86 573 8216 1917 E mail china autonics com E India Autonics Corporation India Liaison Office Tel 91 22 2781 4305 Fax 91 22 2781 4518 E mail india Gautonics com E Indonesia PT Autonics Indonesia Tel 62 21 658 66 740 Fax 62 21 658 66 741 E mail indonesiaGautonics com WE Japan Autonics Japan Corporation Tel 81 265 79 8570 Fax 81 265 79 2442 E mail Support Gautonicsjp co jp M Malaysia Mal Autonics Sensor Sdn Bhd Tel 60 3 7805 7190 Hunting Fax 60 3 7805 7193 E mail malaysia autonics com WE Mexico Autonics Mexico Sales Office Tel 52 55 5207 0019 Fax 52 55 1663 0712 E mail ventas autonics com E Russia Autonics Corp Russia Representative Office Tel Fax 7 495 660 10 88 E mail russia Qautonics com W Turkey Autonics Otomasyon Ticaret Ltd Sti Tel 90 216 365 9117 Fax 90 216 365 9112 E mail info autonics
30. Hardware Installation The software vou are installing for this hardware KANTOO USE To Serial Converter has not passed Windows Logo testing to verify its compatibility with Windows P Tell me why this testing is Important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation 6th At Completing the Found New Hardware Wizard click Finish and driver installation is complete Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for F EAN100 USE To Serial Converter Click Finish to close the wizard Copyright Reserved Autonics Co Ltd 35 5 installation Autonics 9 3 2 36 Checking driver To check the driver right click My computer and select Properties on pop up menu System Properties dialog appears Select Hardware tab and click Device Manager Device Manager dialog appears Check Ports COM amp LPT KRN100 USB To Serial Converter COMx System Properties System Restore Automatic Update Remote Hardware General Computer Name Advanced Device Manager The Device Manager lists all the
31. Men USB Move Copy fove to USB Memory EE o en slew File ss eg 2011 File Infonation E AIRES lt lt Prey Page KAN1AG 20101229_134222 Next Page gt gt Up Directory Into Directors 7 File Information Sa 2011 41 31 TT ma ENTRER PSS md fm Messe EEE USE Hover Cors None ge FILE Info gt gt E Internal 12 1425 Copy to USB Memory HAME gt ALLE KRM TAA 28118131 185409 Move to USB Memory Hane CORRE KRNIAA 2411413121 74853 Delete File Path ede data 2Al 1413 KRNTAA 28118131 175747 BESTE rent Size ARBRE Byte KRNTAA 281 18131_1 re ree cc Prey Page Log Channel Bi KAN BH _2A1 184131171944 Next Page gt gt Log Speed Is LD Ll F R SSSA Le Ir teeta tin Copyright Reserved Autonics Co Ltd 123 g I 8 Parameter detail setup Autonics USER INFORMATION SETUP User information setting You can set user management check system information firmware upgrade 8 8 124 Move to USER INFORMATION SETUP with KB keys preess key to enter USER INFORMATION SETUP 1234566910 ALARH SETUP La DIGITAL INPUT SETUP COMMUNICATION SETUP RECORD SETUP StoTEM SETUP FILE MEMORY SETUP USER INFORMATION SETUP m Parameter list Parameter Password Password mode Login Admin Administrator log in Change Admin Password Change password by administrator User Lock Change user authority Information Check system information Firmware Upgrade Firmware upgrade ere f den S245670 Af wed 15 45 09
32. Mot Found start Date and Time ABBE AYER AR AR AA End Date and Time AAAHHH AA AA AA AA Backup Print Mode Graph You can check saved Backup Data List Backup data list Backup Data is sorted automatically according to the recently occuring order For the information of file selection of backup data list please refer to 8 9 6 Select Print Mode Backup data recording mode setting Copyright Reserved Autonics Co Ltd 131 I 8 Parameter detail setup Autonics 8 9 3 Start Date and Time Start time for data storage OMITA a l es 2e eld bm d234567890NAA a l hec 23882 RECORD BACKUP SETUP ES RECORDO BACKUP SETUP te sus VALUE ates ime Bcor JACKI P sto Backup Data List KANTAR 20110615225126 KRD start Date and Time AREAL ART AR AA A End Date and Time 24008141 AR AR AA Backup Print Hode Graph Backup Set storage start date and time for backup data You can set start date and time Set range is within start date and time to end date and time Set range Date yyyy mm dd Time hh mm ss Factory default 0000 00 00 00 00 00 8 9 4 End Date and Time End time for data storage al te Sf232567890ndlalel LEE ole eh oh es456 789 one Al RE a RECORD BACKUP SETUP ES RECORD BACKUP SETUP MAME gt VALUE sates Time Record Backup Stor Rec Backup Data List KRNIAA2AT1AG15 225126 KRD Backup start Date and Time 0804 81 41 AR AR AA start Dat End Date and Time 2AARATAAT AR AA AA End Dat Backur Pr
33. Please use USB Device as for setting 88 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup During communication if you chaging the communication settings it may cause communication error E Note RS485 communication port of KRN100 is connected for 3 A B SG terminals SG terminal is connectable with shield or SG of converter and you do not need to connect SG terminal To remove noise during RS485 communication use shield cable There are three methods for shield processing l When electric potential occurs between computer and Connects shield cable only for recorder grounded connect shield cable for SG terminal of SG terminal of communication recorder to minimize noise effect not to flow current on module shield cable It is used generally Connects shield for both SG oo When electric optional does not occur between computer terminal of communication and recorder grounded it is effective to minimize noise module and the grounding of influence computer Connects shield for one of SG terminal of communication It can minimize noise effect in case of connecting non module or the grounding of polarity condenser in series computer It is recommended to use SCM US 48T USB RS485 converter or SCM 381 RS232C RS485 converter for RS485 communication between PC and KRN100 If using the non grounded converter between FG and SG it may cause damage to KRN100 and communication
34. break mn A de 823456 76901 rm rue 12 27 28 INPUT SETUP CHI S1UI 1 a SAME VALLE Pan 1 AAH Record Method Instant Filter Tyre Moving Filter Counter 1 Burnout Action In case Input Type Input specification is temperature sensor thermocouple RTD set alarm operation and alarm option for break input In case Input Type Input specification is analog voltage current this function does not operate When input break after moving display value downward or upward according to OFF circuit structure 1 max or min value in graph record state it displays BURN Per When input break after moving display value only upward records max value in cale graph record state it displays BURN When input break after moving display value only downward records min value Down Scale in graph record state it displays BURN Setrange OFF Up Scale Down Scale Factory default OFF Note According to circuit structure when thermocouple Thermocouple temperature sensor RTD RTD temperature sensor s A B terminal or voltage input 60mV 200mV input is break it displays Down Scale When RTD RTD temperature sensor s B B terminal input is break it displays Up Scale Copyright Reserved Autonics Co Ltd 71 I 8 Parameter detail setup Autonics 8 2 ALARM SETUP Alarm setting You can set alarm output specification such as alarm operation mode and alarm option by input channel alarm ON OFF delay alarm
35. card Alarm transistor output 6 KRN AT6 2EA channel Transmitter power Transmitter 24VDC power KRN 24V3 4EA output card output 3 channel Communication RS485 USB Ethernet KRN COM 1EA C output card communication channel X 1 Digital input card alarm output card transmitter power output card are connectable up to 4EA as mixed 3 Example of ordering To use universal input 10 channel digital input 4 channel alarm relay output 5 channel and RS485 communication output it is ordered as KRN100 10102 01 0S and connected I O card is as below e KRN100 Recorder 1EA e KRN UI2 Universal input card SEA Universal input card 1EA is 2 channel and 5EA X 2 channel 10 channel e KRN DI6 Digital input card TEA e KRN AR4 Alarm relay output card 2EA e KRN COM Communication output card TEA Copyright Reserved Autonics Co Ltd Autonics 1 Overview 1 4 Part description 1 4 1 Front and side part INTELLIGENT HYBRID RECORDER VINES ENTER LIST AL SET 1b Display part Displays measurement values as trend graph bar graph or digital number 1 8 12 channel Please refer to 7 1 Screen display Recording print part Records measuring value of data by each channel with designated color Channel information part Write the information by each channel Control key Function key Executes parameter setting and recording and special function Function Using this key for starting stop
36. card KRN UI2 Digital input card KRN DI6 LENN N Analog TC RTD XEach channel is isolated and dielectric strength is 500 V Alarm Output NPN Open Alarm Output Collector Relay Contact 12 24VDC 250VAC 3A 1a 30mA Max RESISTIVE LOAD RESISTIVE LOAD USB 2 0 24VDC 80mA Mini B type RS485 A RS485 B FUEL RS485 S G 24VDC 30mA 10 100 Base T RJ45 Ethernet X24V output of 3EA is isolated individually Copyright Reserved Autonics Co Ltd 29 4 Connection Autonics Note Depending on input specification set the jumper pin of universal input card KRN UI2 channel 1 channel 2 as below figure IO Terminal mm direction _ Ch2 Jumper Input specification Input break alarm 0 to 20mA 4 to 20mA Enables only 4 to 20mA TC RTD 60mV 200mV 2V 110 SV 5V 1 to 10V 30 Copyright Reserved Autonics Co Ltd Autonics 5 Installation i 5 Installation 5 1 Installation place Install this unit in place where the below conditions are satisfied Place where ventilation is well To prevent from malfunction and damage by overheating use temperature range 0 to 50 C install this unit where ventilation is well In case
37. digital input function is operating X 3 When digital input operation status is set as Level in RUN mode you cannot operate starting stopping recording with front B key If it set as Edge front key operates starting stopping recording When reservation record Reservation is set and now is reservation recording state digital input function is not available as RUN mode This is available in record stop state by reservation record Set range None Run Memo ListOut Speed Alarm Reset Factory default None Copyright Reserved Autonics Co Ltd 85 I 8 Parameter detail setup Autonics 8 3 3 DI L Reset No Reset alarm number me Eo eaae 78901 lues 223657 Lee aS 23456 789 0NRLAEP med 22 3i 0a a DIGITALIHFUT SETUP S6DI OR DIGITALIHPUT SETUP SADI Hone NAME gt VALUE gt lt MAME gt WAL ALL select OF Card SOU I select DI Card TR SfAL 1 OI 1 Type Alarm Reset OI 1 Tyre TR S 7AL DI 1 Reset Ho E DI 1 Reset Ho TR S57AL 3 OI 1 Status Ed OI 1 Status TR S7AL 4 Ol 2 Type Ol 2 Type TR 8 7AL 5 Ci ate Ci ate E a Select alarm to reset at digital input Set DI L Type Select digital input 1 as forced alarm recet Alarm Reset it is activated Alarm reset is available when alarm option is Alarm latch or Alarm latch and standby sequence and it is not alarm condition Setrange None ALL S AL Factory default 8 3 4 DI L Status Operation status me f den SI 23456 890 med 22
38. installing several KRN100 space each other by panel cut out Place where vibration is not severe If there is too much vibration it may cause malfunction such as print error For more information about vibration please refer to 2 Specification In case of temperature measurement with thermocouple temperature sensor at the place where temperature is fluctuated data error may occur You should warm up this unit over 30 min to acquire accurate data before using it At the place where temperature and humidity is fluctuated excessively recording paper color may be changed Copyright Reserved Autonics Co Ltd 31 5 Installation Autonics 5 2 Installation 5 2 1 Bracket mounting Ist Install KRN100 on the processed panel as panel cut out diagram Mount fixing brackets on upper lower parts lt Panel Thickness 2 to 8mm l RO Fixing bracket 2nd Tighten fixing brackets on upper lower parts to fix on the panel with phillips screwdriver Torque 0 4Nem Philips screwdriver 32 Copyright Reserved Autonics Co Ltd Autonics 5 Installation ff 5 2 2 Additional I O card connection Ist To connect I O card additionally turn OFF the power of KRN 100 Remove the proper slot cover to insert I O card with flat head screwdriver or knife 7 p T G ENT
39. numbers special characters by My KA Ea and keys No Front key Press D key once and English capital letters English small letters and special character virtual keyboard is switching When pressing and holding MZ key screen of Function key is displayed 2 Moves digit to select character of virtual keyboard X 1 Enterable characters are as below e English pepe letters Copyright Reserved Autonics Co Ltd 41 i 6 Display Autonics 6 2 3 Parameter setting display 1234567891010 mj lu 2234567890 wes aasia Ea E INPUT SETUP INPUT SETUP CH3 5cU1 ALARM SETUP NAME gt DIGITAL INPUT SETUP select UT Card COMMUNICATION SETUP Input Set Copy RECORD SETUP LCD Paper Record SYSTEM SETUP Pen Color FILE MEMORY SETUP Sir Record Zone CI LI E LTE il CI LE m Lan Press front key for 3 sec and it enters parameter setting group When entering parameter setting group setable parameter setting groups are displayed At parameter setting group press key to enter parameter setting For more information of parameter detail setup please refer to 8 Parameter detail setup 42 Copyright Reserved Autonics Co Ltd Autonics 7 Operation 7 Operation Screen display m Vic FE Trend graph Ep Par graph ME WY MO WAN I DISPLAY Mo DISPLAY Digital number Special function for record Ca Start Stop recording Parameter Gigs setting group KE gt Parame
40. output relay relay contact etc Move to ALARM SETUP with BE keys press key to enter ALARM SETUP pA Pb 023 45679902 Aa Web ae e INPUT SETUP ae ALARM SETUP EH S1UI a ALARM SETUP NAME gt DIGITAL INPUT SETUP select UI Card COMMUNICATION SETUP Hlarm Set Copy CH Select RECORD SETUP Alarmi Type PY Hi StaTEM SETUP Alarmi Ret CH FILE MEMORY SETUP Alarmi Option a i al ci m Parameter list Factory Select Ul Card Select universal card input CcHO SOUI O o Jr Alarm Set Copy Copy alarm parameter No Select CH SCUI CH Select Alarm 1 Type PV Hi OFF PV Hi PV Lo DV Hi Alarm Type Alarm 1 operation mode Alarm2 DV Lo SBA PEND Type to Alarm4 Type None Alarm Ref Channel Alarm reference None CHO SOUI D channel Alarm Option Alarm 1 option None Latch StBy Lat St Ro Alarm Value Alarm set value F S of INPUT TYPE by channel Alarm Hysteresis Alarm 1 hysteresis F S of INPUT TYPE by channel Alarm 1 ON OFF Delay Alarm 1 ON OFF 0 to 3600 sec Os output delay time Alarm Alarm No Alarm 1 output alarm None SLJAO None number 1 Select Alarm Card Select alarm output Automaticall card y set N O 0NC When connecting Relay type KRN AR4 alarm output card AL1 to AL4 are Alarm Status Relay and transistor N O eN C activated N O output method When connecting transistor type KRN AT6 P N O eN C alarm output card AL1 to AL6 are N O activated N O N C N O
41. pms to User5 pms User1 pms USB to User5 pms USB Factory default None A Caution Be sure that if selecting Default pms file every set value is initialized as factory default Save the current set parameter as Save Set File parameter setting file storage at first and initialize it for the provision User1 pms to User5 pms User1 pms USB to User5 pms USB file is selected all parameter setting information of KRN100 is changed as the set value of the selected parameter save file Set value changing may be also affected to every setting of KRN100 s overall operations Check possible problems occuring on system and change the desired set value 8 7 2 Save Set File Save parameter setting file a ON F458 TAIT A OE Ed Ta on 3456 7 SS eA s FILEHEMORY SETUP ai FILEHEMORY SETUP ey NAME gt MANE gt Load Set File Load Set File sere sert pms save set File save set File Select Memory Status Memory Status pr Memory Clear Clear Memory Clear oe USB LogData Save Disable USB LogData Save ig JPG hiaidh as ats Li LOL le Tafa sero pms Saves current set parameter set value to User1 pms to User5 pms file of inner memory In case of empty file it displays gray Set range None User1 pms to User5 pms User1 pms USB to User5 pms USB Factory default Select Copyright Reserved Autonics Co Ltd 119 I 8 Parameter detail setup Autonics 8 7 3 Memory Status Memory capacity Bal Ea b
42. scale Lower limit scale Lower limit scale 7 2 20 x 2000 1000 10 5 Two Unit ml Te EERE ee ee a INPUT SETUP CHi S1UI 1 lt NAME gt VALUE Low Scale High Scale special Function Two Unit 7GAmnHa Akg cnz ds tebditireetet Reference Channel Nc Ho For compound pressure if input pressure is lower AR atmospheric pressure 0 it displays the degree of a vacuum with mmHg unit If input pressure is higher than or same as atmospheric pressure 0 it displays positive pressure with kg cm unit When using Two Unit function lower limit value is fixed as 760mmHg and kg cm value is able to set within set range 1 to 35 Two Unit limits scale point as O 0 0 0 00 When using Two Unit display unit is automatically changed as mmHg or kg cm The calculation with Record Method Data storage method and Filter type Input digital filter is impossible and ignored due to different type of two unit value e Set range 1 to 35 e Factory default Copyright Reserved Autonics Co Ltd 65 I 8 Parameter detail setup Autonics EO Ex If pressure range is 60mmHg to 3kg cm and pressure transmitter outputs 4 to 20mA for 4mA input it displays 60 mmHg 8mA input is unit changing point For 20mA input it displays 3kg cm 3kg om Unit changing Range QKGI Chae nas 3 point mA 760mmHg to 1kg cm 12 130 2 1kg cm 760mmHg
43. to 5kg cm 6 740 Unit changing point 3 760mmHg to 10kg cm 5 498 _ 760mmHg to 15kg cm 5 031 AmA A 12mA 16mA 20mA a 760mmHg to 20kg cm 4 786 f 2 760mmhHg to 25kg cm 4 635 760mmHg to 30kg cm 4 533 760mmHg to 35kg cm 4 459 EEE 760mmHg E Note 16 X 1 033 Unit changing point X Y 4 4 to 20 mA output interval Max pressure range value Ex For 760 to 3 kg cm itis 3 1 033 Converted value from 760 mmHg to kg cm unit value same unit Y Use pressure 1 033 Ex Use pressure is 0 Y is 1 033 4 a l Output value for zero 4 00mA Set range In case Input Type Input specification is temperature sensor thermocouple RTD None Difference In case Input Type Input specification is analog voltage current Linear Root Square Two Unit Two Unit is activated for current input 0 to 20mA 4 to 20mA Factory default None 66 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 1 13 Reference Channel Reference channel mr Mo 523456789012 fr ru esses Plc Mo 89123456 78910124 5 fr rue 152 Se 35 INPUT SETUP CH1 S1UI 1 a INPUT SETUP CHI S1IUI 1 Hone ae NAME gt NAME gt VALU CHI S1UI 1 Low Scale Low Scale CH amp 1UI 2 Hish Scale Hish Scale CHa seUT 1 special Function special Function CH4 S2UT 2 Two Unit f6emmHg Hka cm Two Unit 7G mmHa 7 CHS SSUI 1 Reference Channel Reference Channel CHE S3U1 2 mi
44. 234567890ndAet 143403 FILEMEMORY SETUP D NAME gt VALUE Load Set File Hone save Set File Select Memory Status d Memory Clear Clear USE Loglata Save Disable fatt fan oto Displays system memory usage in If memory usage is 100 depending the set value of 8 7 6 Memory Save Option Memory storage option new data is overwritten on oldest backup data or it stops saving backup data Display range 0 to 100 Factory default 0 Note Inner system memory of KRN100 is 512 Mbyte and KRN100 supports an external USB memory up to 32 Gbyte Another file to be saved data is created when it is over 100 Mbyte Below table is save time for 100Mbyte data by the number of input channels The number of CH 7 channels 8 channels 9 channels The number of CH 1 channel 2 channels 3 channels 4 channels Approx 33 days 5 channels 6 channels 8 7 4 Memory Clear Delete memory muet ES TRE AE kane FILEMEMORY SETUP MAME gt lt Log File Clear gt Load Set File 10 channels Approx 20 days 11 channels Approx 18 days 12 channels Approx 17 days Save Set File Memory Usage d Memory Status d Memory Clear rav Cancel All Clear USE Loglata Save nantes otic Delete the saved log data on system memory Current saving backup data is not deleted when deleting backup data Set range Cancel All Clear Factory default Clear 120 Copyright Reserved Autonics Co Ltd A
45. 5 Port Use RS485 communication 90 x Copyright Reserved Autonics Co Ltd Autonics Table of Contents i 8 4 3 Baud Rate Baud rate 4 90 8 4 4 Parity Bit Communication parity bit 91 8 4 5 Stop Bit Communication stop bit 91 8 4 6 Termination Set Terminating resistance 91 8 4 7 Response Wait Time Communication response wait time 08 92 8 4 8 Protocol Communication protocol 92 8 4 9 RS485 Com Write RS485 communication write 92 8 4 10 Ethernet Port Use Ethernet communication rronnrrnnnrrnnnernnnrrnnnnvnnnnnnrr 93 8 4 11 IP Address IP address de nn names descente 95 8 4 12 Subnet Mask Subnet Mask 95 8 4 13 Default Gateway Default gateway rrrnnnrrnrrnnrrrrrnnnrrnrnnnnrrvrnnnrrnrnnnrennnnn 95 8 4 14 Ethernet Com Write Ethernet communication write 96 8 4 15 USB Device Port Use USB communication 96 8 4 16 USB Com Write USB communication write 96 8 5 RECORD SETUP Record setting 97 8 5 1 Record Mode Recode mode 98 8 5 2 Digital Print type 1 line record channel during numeric recording 99 8 5 3 Standard Speed Standard record speed 100 8 5 4 Option Speed Option record Speed ccccccceecceeeeeeeeeeeeceeseeeeeeeeeees 100 8 5 5 Memo Period Digital MEMO period rrrarrnnnnnnnnnnnnnnnnanrnnnnennnnennnnnnnnnennn 101 8 5 6 Divide Zone Recor
46. 85 RH ment E Humidity XIf using this unit at place with high humidity it may cause paper jam Please do not use this unit at place with high humidity TEE Unit weight Approx 1 7 to 2 0kg X 1 For more information of universal input please refer to 2 2 I O card X 2 Environment resistance is rated at no freezing or condensation Copyright Reserved Autonics Co Ltd Autonics 2 Specification 2 2 I O card 22 JPt100Q DPt100Q DPt50Q Cu100Q Cu50Q Supply current 420uA Input Thermoco specific B C W5 E G J K L L Russia N P R S T U uple ation i ron Voltage 60mV 200mV 2V 1 5V 5V 1V 10V nalo i Current 0 00 20 00mA 4 00 20 00mA Voltage V Min 150kQ Universal Input impedance RTD thermocouple voltage mV min 2MQ KRN UI2 input card current 510 Warm up time Min 30 minutes Thermoco Room temperature 25 C 5 C section uple 0 1 F S 1 digit accurac 3 Out of range of room temperature 0 2 F S 1 digit J Analog RTD 500 to 850 C is PV value 0 5 1 digit Thermocouple Below 100 C is 0 3 F S 1 digit ON Max 1V of residual voltage OFF Max 0 1mA Noncontact input Digital leakage current input card ON Max 1kQ OFF Min 100kQ Contact input Outflow current for short Approx 4mA Capacity 250VAC 3A 30VDC 3A 1 Form A resistance load Mechanical Min 50 000 000 operations Life Electrical Min 100 000 operations 3A 250V AC 3A 30
47. Alarm On Delay channel flashes on screen if it is still alarm condition alarm output turns ON Alarm ON channel flashes on screen Even after standby the set time when alarm reset condition alarm ON Alarm OFF Delay channel display is hold if it is still alarm reset condition alarm output turns OFF Alarm ON channel resets the display Alarm Value IN N Time Alarm output with no ON set alarm ON OFF Delay OFF a FY Oo ON Delay ON Delay OFF Delay OFF Delay Alarm output with set ON hud gt MP alarm ON OFF Delay off No alarm output PN Set range 0 to 3600 Factory default Os Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup i 8 2 9 Alarm Alarm No AlarmL output alarm number fel Po 234561890106 lues attest bend 1 a 123256 7890NRA 8 ae a ae ALARM SETUP CH3 S2U1 1 SR ALARM SETUP CH3 S2U Hone NAME gt NAME gt TA S7AL 1 th Hlarmi Option Alarmi Yalue TR STAL 2 A Alarmi Value Alarm Hysteresis TR S TAL 3 441 Hlarmi Hysteresis l Alarmi ON Delay TR S 1AL 4 A Alarmi ON Delay Hlarmi Off Delay TR S TAL 5 441 Alarm Off Delay O Alarm Alarm Ho TR STAL 6 16 n nr Ab Fat mn fun n ote ag Lid Select alarm output number to output alarm in alarm ON If the setting as None and when alarm operation occurs it displays alarm on the screen and records alarm operation mode and alarm occurrence time on recording paper but it does n
48. Autonics Co Ltd Autonics 2 Specification 2 3 Input specification and measuring range passe qe ET a A K CA 200 0 to 1350 0 328 0 to 2462 0 73 2 t0 1623 2 2 to 1623 2 J IC 200 0 to 800 0 328 0 to 1472 0 73 2 to 1073 2 E CR 200 0 to 800 0 328 0 to 1472 0 73 2 to 1073 2 T CC 200 0 to 400 0 328 0 to 752 0 73 2 to 673 2 B PR 100 0 to 1800 0 212 0 to 3272 0 373 2 to 2073 2 R PR 0 0 to 1750 0 32 0 to 3182 0 273 2 to 2023 2 S PR 0 0 to 1750 0 32 0 to 3182 0 273 2 to 2023 2 Thermocouple N NN 200 0 to 1300 0 328 0 to 2372 0 73 2 to 1573 2 C TT x1 0 0 to 2300 0 32 0 to 4172 0 273 2 to 2573 2 G TT xe 0 0 to 2300 0 32 0 to 4172 0 273 2 to 2573 2 L IC 200 0 to 900 0 328 0 to 1652 0 73 2 to 1173 2 L Russian type TC L_R 0 0 to 600 0 32 0 to 1112 0 273 2 to 873 2 U CC 200 0 to 400 0 328 0 to 752 0 73 2 to 673 2 Platinel IT 0 0 to 1350 0 32 0 to 2462 0 273 2 to 1623 2 Cu500Q 200 0 to 200 0 328 0 to 392 0 73 2 to 473 2 Resistance Cu1000Q Cu100 200 0 to 200 0 328 0 to 392 0 73 2 to 473 2 temperature JPt1000 JPt100 200 0 to 600 0 328 0 to 1112 0 73 2 to 873 2 detector RTD CSSS DPt50 200 0 to 600 0 328 0 to 1112 0 73 2 to 873 2 Demon DPt100 200 0 to 850 0 328 0 to 1562 0 73 2 to 1123 2 seam em ne m Analog 5 000 5 000V EE Resolution imv display range depends on the decimal point position Resolution 1 00 10 00V 1V 10V 10mV 0 00 20 00mA 0 20mA Resolution 10uA Curren
49. BRID RECORDER pe Elu bl 23456789 0 Je anm rE 16 28 37 mg e clol e r e 1 2 3 eH ts tk ut Ni fals 6 rc gt ay ea dj Pl KRN10C LIST AL RESET DISPLAY 18 Copyright Reserved Autonics Co Ltd Autonics 1 Overview i 1 4 2 Back side HHH Slot C for connecting communication output card KRN COM Q Slot 7to10 for connecting digital input card KRN DI6 alarm relay output card KRN AR4 alarm transistor output card KRN AT6 transmitter power output card KRN 24V3 You can connect total 4EA by combining digital input card alarm output card and transmitter power output card as below combination example KRN DI6 KRN AR4 KRN AT6 KRN 24V3 Total 4EA 1EA 1EA 1EA 1EA KRN DI6 KRN AR4 KRN AT6 Total 4EA 2EA 1EA 1EA KRN AT6 KRN 24V3 1EA SEA Total 4EA 3 Slot 1 to 6 for connecting universal input card KRN UI2 4 Power connecting part 100 240VAC 50 60Hz X Above back side image is connected every otuput card to help your understand Factory default is only connected with universal input cards Slot1 and 2 Copyright Reserved Autonics Co Ltd 19 1 Overview Autonics 1 4 3 Inside ee a
50. CKUP SETUP a COMMUNICATION SETUP NAHE gt RECORD SETUP Record Backup SYSTEM SETUP Backup Data List File Hot Found FILE MEMORY SETUP start Date and Time HARARE AA AA AA USER INFORMATION SETUP End Date and Time AGRA EGER AG AG AA RECORD BACKUP SETUP Backup Print Mode Graph 1 Cite A m Parameter list Record Backup Backup data record lt Start Backup Data List Backup data list File Not Found Start Date and Time Start time for data storage Date yyyy mm dd Time hh mm ss Dae yy mm aa onas 0000000 End Date and Time End time for data storage Date yyyy mm dd Time hh mm ss Pee preemie nme aatan Backup Print Mode Backup data record mode Ro Grah re Mode Backup data recording mode Graph Digital When printing with backup data the saved data in backup data is accurate but backup data printout may not be same 100 with the real data due to the difference between printing time and backup time Please use backup data as only for reference For printing backup data KRN100 reads saved backup data in memory from beginning to end at first and starts printing If backup data section is long or backup data is saved as low speed record mode reading takes a lot of time Therefore print only for the desired section In graph mode record speed is changed by Standard speed Alarm or Option Speed Backup data is printed with Standard speed Therefore original printout and backup print
51. DIGITAL INPUT SETUP Device Name KRNTAR Recorder COMMUNICATION SETUP BURNS Date Time 2011 06 01 Wed 14 45 24 RECORD SETUP BURM C Date Type vyyy mnedd SYSTEM SETUP summer Time Disable FILE MEMORY SETUP Summer Time Period a ALARM SETUP eC CNAME gt VALUE m Parameter list Device Name Device name Max 16 characters KRN100 Recorder Date 2000y01m01d to 2099y12m 31d Date Time Date Time ai Set as factory default Time 00h 00m 00s to 23h 59m 59s Date Type Date type yyyy mm dd mm dd yy dd mm yy yyyy mm dd Summer Time Summer time Disable Enable Disable Summer Time Period Summer time period 01m 01d 00h to 12m 31d 23h Reservation Type Reservation record Disable Single Repeat Reservation Period Reservation record 2000y 01m 01d to 2099y 12m 31d period Reservation Time Reservation record time 00h 00m 00s to 23h 59m 59s Alarm Sound Alarm sound OFF Min Standard Max 1 channel to 4 channel 25 125 250 Sampling Rate Sampling period 5 channel to 12 channel 125 250 Log Speed Save period 0 to 3600 Backlight LCD backlight brightness OFF Min Standard Max Standard Backlight On Off LCD backlight ON method Temp Always X Shaded parameters are affected by set value of other parameters Please refer to specific descriptions of each parameter Copyright Reserved Autonics Co Ltd 111 g I 8 Parameter detail setup Autonics 8 6 1 Device Name D
52. Ethernet IP Address 192 168 1 2 Ehternet Mac Address Ag ed 48 AA AA AA Slot UIZ Sti S UL SU SAUL S6 UI S6 U1 lt NAME gt LUE Password Enable Login Admin Change Admin Password FR User Lock OFF Information Uisplay 1 j Cu LS Ris i Slot Option Be ra FESE F Check system information of KRN 100 You can firmware version an USB memory capacity communication concerns slot connection status etc Note If connected and displayed card on slot and actaul connected card is inconsists check the connect status of card and re supply power If it is not recognized even though re supplying power please contact our service center Autonics service center 82 32 820 2343 Copyright Reserved Autonics Co Ltd 127 I 8 Parameter detail setup Autonics 8 8 6 Firmware Upgrade Firmware upgrade mn fin 82345678 90 drm rue 7 2 5 USERINFORMAT ION SETUP Password Disable FA NAME gt WALLE Login Admin Change Admin Password User Lock Information Hise play ET Firmware Upgrade Updates KRN100 firmware When upgrading firmware parameters set values are initialized Set range Factory default Automatically set G Note Firmware upgrade Ist Visit our homepage www autonics com to download KRN100 firmware file krn100 fwu 2nd Copy the downloaded firmware file to an USB memory s loot top directory and connect an USB memory to KRN100 3rd Check that firmware is reco
53. High Range Upper limit input value al ee ON 23456 7890 le SORT aml Mb 023456 78900022 ee eet Pees INPUT SETUP EH S1UI a TER I TG mj a e efol e rje BE Input Type med si ki ei mM Nn f a 5 6 biselay Temp Unit t Ao r al als tjul 7 ala Low Range lilly iz sel fl oll pedal aar Set the actual used upper limit input value within for range of Input Type Input specification e Set range Lower limit input value Low Range F S 5 to max input range value In case input range is 0 to 100 C set range is 5 to 100 C e Factory default Set the displayed graph scale value on recording paper and LCD in temperature sensor input type Thermocouple RTD They does not displayed in analog input type You can designate the record range and record specific section as detail graph by these parameters If graph scale range is small resoultion is also lower in proportion to recording range 3 Low Graph Scale Lower limit graph scale value fu 0 Pa Ares a567es 8 el Mu 9234567890 A rnd ne EUT SETE MESE a mlilelcrolelrle pets input Type 5 Ee J ia yer ea B G g o rP afr s yryu 17 8 9 Low Graph Scale HE pg ve Space Fire High Graph scale Within the input range of Input Type Input specification set lower limit graph scale value e Set range Min value of input range to upper limit graph scale value High Graph Scale F S 5 When TC K input range is 200 0 to 1350 C s
54. Instant Filter Counter The number of digital 1 to 128 filter Fe Action Display setting for OFF Up Scale s Dani Scale OFF Shaded parameters are affected by set value of other parameters Please refer to specific descriptions of each parameter Note Range Scale Point Decimal point position Display Temp Unit Display unit Temperature unit Low Range amp Graph Scale Lower limit input value and graph scale value When changing set value of l a High Range amp Graph Scale Upper limit input value and Input Type input type gt graph scale value parameter E Low Scale Analog lower limit scale value High Scale Analog upper limit scale value Special Function Input special function parameters set values are initialized 54 Copyright Reserved Autonics Co Ltd Autonics 8 1 1 8 Parameter detail setup Select UI Card Select universal input card mt PON 3456789 0A lui al D 01234256 78 90NDA ET lue 13 INPUT SETUP CHA S2U1 1 QRS BORN CHA S2U1 1 GR ES NAME gt VALU CHd s2Ul 2 NAME gt VALU CHd s2Ul 2 select Ul Card Ck CH5 S3UI 1 select UI Card Ck CHS S3U1 1 Input Set Copy CHE SSUT 2 Input Set Copy CHE S3SUT 2 LOO Parer Record CHi S4U1 1 LOO Parer Record CHi S4U1 1 Pen Color CHe S4UT 2 Pen Color CHe S4UT 2 Record one CHS S5UT 1 Record one CHY S5UT 1 Select the channel of universal input card KRN UI2 to be set One universal input card has two channels KRN100 automatically searches sl
55. LE 4i Sm i DH D CH 2 850 1 ECE aE EYE ETT Erti er CH 3 8255 H eH Oi CH 4 2524 3 iC HH 74 D CHS badet E CE PH tg irt Hare Tie O cH 6 192 2 EC j de 7 rT FE 11 00 00 OC OPT rTP PE PPE Pe O For the information about alarm abbreviations please refer to 8 2 3 Alarm Type Alarm operation mode For the information about error abbreviations please refer to 11 1 Error message Copyright Reserved Autonics Co Ltd 99 I 8 Parameter detail setup Autonics 8 5 3 Standard Speed Standard record speed fel So 202345678901 lues el Po dll23456 789024 ma sat poas a2 RECORD SETUP ae RECORD SETUP le NAME gt NAME gt Record Mode Record Mode Digital Print Tyre Digital Print Tyre Standard Speed 2 Ann h Standard Speed Option Speed 2 Am h Option Speed Hemo Period Hemo Period PL 1 tri mit Pl ri mate Designate record speed on recording paper Recorder speed is indicated as feed length of recording paper per an hour mm h and it is activated only when Record Mode Record mode is set as Graph Graph Set range 10 20 40 60 120 240mm h Factory default 20mm h 8 5 4 Option Speed Option record speed le Mo ON 2S45R 789 mes aat ml EP ON 234567890NAA ra set apsest ta te RECORD SETUP OR FECOROD SETUP NAME gt VALUE NAME gt Record Mode Graph Record Mode Digital Print Type OnelH Digital Print Type st
56. ON Therefore KRN 100 takes booting time max 20sec and maintains Normally open status In case of RUN mode after booting it maintains use defined output type Normally Open or Normally Closed 82 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 3 DIGITAL INPUT SETUP Digital input setting You can set executing function by digital oe card operation stauts etc Move to DIGITAL INPUT SETUP with KZ ES an KEYS Press key to enter DIGITAL INPUT SETUP id ON 1234567090ND Ten lues tisse a Ba ON 23456 TAS AG PSA INPUT SETUP OIGITALINPUT SETUP STOI le ALARM SETUP NAME gt WALUE gt DIGITAL INPUT SETUP Select DI COMMUNICATION SETUP DI 1 Type None RECORD SETUP DI 1 Reset No mi oroTEM SETUP DI 1 Status a FILEMEMURY SETUP Ul 2 Type None Lit HA Hl E un Far m Parameter list Select DI Card Select digital input card S7DI lt S8DI lt S9DI lt S10DI Automatically set ee None Run Memo ListOut Speed DI L Type Select digital input O None Alarm Reset DI L Status Operation status Edge Level Shaded parameters are affected by set value of other parameters Please refer to specific descriptions of each parameter Copyright Reserved Autonics Co Ltd 83 I 8 Parameter detail setup Autonics 8 3 1 Select DI Card Select digital input card fe im SP 23456 TASMAN med 2562 Pero Pm Sl 23456789 0MNAJEN med 22 30 27 a DIGITALIHFUT SETUP S6DI OR DIGITALIHPUT SE
57. Parity Bit Stop Bit Designate baud rated Set range 2400 4800 9600 19200 38400 unit bps Factory default 9600 90 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup i 8 4 4 Parity Bit Communication parity bit fe em 823456 BSA wep 22 54 08 COMMUNICATION SETUP lt H AHE gt VALUE Modbus Address 1 Hide Port Enable Baud Rate SRA Parity Bit Hone atop Bit Designate communication parity bit Set range None Odd Even Factory default None 8 4 5 Stop Bit Communication stop bit mf Pa SP 23456 788 DMS ueb 22 33 15 a COMMUNICATION SETUP MAME gt Modbus Address Rsd Port Baud Rate Parity Bit Stor Bit Designate communication stop bit Set range 1 2 unit bps Factory default 2 8 4 6 Termination Set Terminating resistance OKIENNA a COMMUNICATION SETUP NAME gt Raga Port Baud Rate Parity Bit stop Bit Termination set Desigante wheter using terminating resistance You do not need to external terminating resistance 1200 because KRN 100 is enable to use terminating resistance by parameter setting Setrange Enable Disable Factory default Disable Copyright Reserved Autonics Co Ltd 91 I 8 Parameter detail setup Autonics 8 4 7 Response Wait Time Communication response wait time fet Fi S1234567890NAAEN lues 22 24 25 COMMUNICATION SETUP lt HAHE gt Baud Rate Parity Bit stop Bit
58. SS To recognize network ID part and host ID part of IP address set 32 bit address allowing to IP packet receiver To enter correct set value whenever press 7 keys it displays inputable subnet mask value is displayed Set range 0 0 0 0 to 255 255 255 255 Factory default 8 4 13 Default Gateway Default gateway mt Pao ON 3458 TAIT Ae me EE el Pm 023456 7 ASA moi 17885 ae te COMMUNICATION SETUP NAME gt VALUE ASde5 Com Write Enable IF Address 197 165 1 a Ethernet Port Disable Subnet Mask 255 255 255 IP Address 192 188 1 2 ca Subnet Hask 255 255 255 6 oe EE Default Gateway 92 168 1 LF HUUT ESS Designate IP address to connect IP router directly Set range 0 0 0 0 to 255 255 255 255 Factory default Copyright Reserved Autonics Co Ltd 95 g I 8 Parameter detail setup Autonics 8 4 14 Ethernet Com Write Ethernet communication write fel MP 2345678901 6 med 22 35 18 COMMUNICATION SETUP ae NAME gt VALUE gt Ethernet Port Disable IP Address 192 168 1 2 Subnet Mask 255 255 255 Default Gateway 192 168 1 Ethernet Com Write D lur Dis ooh set whether changing the set value of KRN100 parameter by Ethernet communication To read the set value of each parameter is available regardless of the communication write enable disable setting Set range Enable Disable Factory default 8 4 15 USB Device Port Use USB communication
59. Speed ei SYSTEM SETUP Option speed 2 AmmH FILEAMEMORY SETUP Hemo Period 15min 3 ALARM SETUP MAME gt VALUE gt Parameter list Record Mode Recode mode Graph Digital Digital Print t 1 li d ch I duri i igi a rint type 1 line record channel during numeric OneCH TwoCH TwoCH recording Standard Speed Standard record speed 10 20 40 60 120 240mm h 20mm h Option Speed Option record speed 10 20 40 60 120 240mm h 20mm h Memo Period Digital memo period Refer to detail descriptions Divide Zone Record zone division None 2 to 12 Standard Period Standard record period 00m01s to 99m99s Option Period Option record period 00m01s to 99m99s Listing Language Language for list output Korea lt English Alarm Speed Alarm record speed Power On Status Record status when power ON Hold Run Stop Run Status List printing at start recording OFF ON List Out Option List record option Standard Option Standard Zone Dot Line Distance Dot line for zone division None to 8 0mm CH Print Dist R d int If h ch rint Distance Record interval for each channe st per graph Start Line Print Start line when starting record ON OFF ON Range Print Time Input range record period Disable 1to 24 hour X Shaded parameters are affected by set value of other parameters Please refer to specific descriptions of each parameter Copyright Reserved Autonics Co Ltd 97 I 8 Par
60. T 2011 06 14 11 33 16 TUE t Start Line O CD O O O CO Set range ON OFF Factory default ON 8 5 17 Range Print Time Input range record period fe Fm 23456789 MAVEN med 22 39 20 a RECORD SETUP NAME gt VALUE gt List Out Option standard Dot Line Distance CH Print Distance start Line Print ON Range Print Time It is actiaved when Record Mode Record mode is set as Graph Set record period of High Low Range amp Graph Scale High Low input value and graph scale value Set range Disable 1 to 24hour Factory default Disable Ex O INPUT RANGE OR SCALE 2011 06 14 THU 11 35 27 OE O 5 O CH 1 200 0 1350 0 D CH 2 200 0 1350 0 O D O T D O CH N 20070 1350 0 ap PPT D Note During Range printing the other data except graph is not recorded within pritted range Be sure that if there is too many channel numbers or if Range Print Time interval is too short with low speed various information about channel is not printed at Range print zone 110 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 6 SYSTEM SETUP System setting You can set system parameters of KRN 100 Set the item related system date and time reservation record option etc Move to SYSTEM SETUP with keys press key to enter SYSTEM SETUP DISPLAY 7 Pasero mee med bed km 00123456 7890 me ued 14 49 22 INPUT SETUP AH 3 700 SYSTEM SETUP
61. TE END ree F END BACKUP PRINT NAME gt Record Backue Stor Backup Data List KRMIAA 2A118649 144512 KAD start Date and Time 2411 46 49 14 45 46 End Date and Time 2411 46 49 14 45 56 Backup Print Mode Graph Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup X H Alarm output hysteresis Hysteresis If even one alarm occurs alarm ON icon marks the specified channel to check whether alarm has occurred 1 Record Mode Record mode is Graph lt records alarm sign alarm operation mode and occurrence time on recording paper with the set record color in Pen Color of INPUT SETUP Alarm sign is recorded at alarm set value position O A V oO O 14 00 45 TM Alarm ON in 3 channels O CD O A VA CH1 AL 3 14 00 33 mer 3 alarms ON in 1 channel O OD o CH1 DV LO 13 55 03 s DV Lo Deviation lower limit alarm ON O A CH6 DV HI 13 52 45 gt DV Hi Deviation upper limit alarm ON O CD O CH1 PV LO 13 47 55 OL PV Lo Absolute value lower limit alarm ON O O CH6 PV HI 13 45 21 br PV Hi Absolute value upper limit alarm ON O O P CH1 PEND 13 32 11 P END No recording paper ON S CH1 SBA 13 31 24 lt SBA Input break alarm ON Alarm ON from 1 channel Records alarm sign of corresponding channel s graph Records also alarm and time information at right Alarm ON at the same time Records alarm sign of corresponding channel s graph Records from over 2 channels onl
62. TER TE mli slc ole r cl BE Low Scale A G ea H I o k Lt mjNnj lafl5 B i KN sen neces BITE gg o r afnfsjrful frjefsl To Unit NT L peee L TO EE Reference Channel INE Ho Set scale value for upper limit input value High a e Set range 99999 to 99999 9999 9 to 9999 9 999 99 to 999 99 99 999 to 99 999 9 9999 to 9 9999 Depending on Scale Point setting the range is different e Factory default 62 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup i 8 1 12 Special Function Special function OA OL AE ud INPUT SETUP CH5 S3UI 1 FI NAME gt VALUE gt Low Scale A A High scale 1AA Special Function Two Unit Reference Channel It dispalys the applied measuring value of the set special function Depending on Input Type Input specification appliable special function is different Set range When input type input specification is temperature sensor thermocouple RTD None Difference analog voltage current Linear Root Squre Two Unit Two Unit is displayed when Input Type input specification is set as 0 to 20mA 4 to 20mA Factory default None Below graph s patterns are liner root square for analog input Lower limit input value 5V Upper limit input value 5V Lower limit scale 1000 Upper limit scale 1000 Scale 1000 Root 500 Fa 500 e 1000 Copyright Reserved Autonics Co Ltd 63 i 8 Parameter det
63. TUP SADI NAME gt NAME gt select OF Card SG OI 1 Type OI 1 Type OI 1 Reset Ho OI 1 Reset Ho OI 1 Status OI 1 Status Ul 2 Type Ul 2 Type Select digital input card KRN DI6 to be selected KRN100 searches connected digital input card automatically on slot and recognizes the number of digital input card as soon as power is ON Channel name is as below Set range S DI lt S8DI S9DI S10DI Factory default Automatically set S9DI This means connected digital input card on 9th slot 84 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 3 2 DI L Type Select digital input C mj Po SJ 23456 78804 an aiaa el PP 23456 aoe Me irae is ai VG m DIGITALINPUT SETUP S6DI OR CIGITALIHEUT SETUP S1A0I lt MAME NAME gt select DI Card select DI Card if o me Hone i ao Me heset No Heset No DI 1 Status DI 1 Status nl DIE Type De Type Alarm Reset Min signal Short x1 Icon input Starts Stops recording on STOP RU ST n Executes digital memo Outputs parameter set LI ee ee Executes to record with set each ate option record speed and Standa Option Standard period Option speed rd Option period digital period In case alarm option is aly FORGE alarm latch alarm output is ot he Reset reset by force X 1 At every min signal input width over 0 3 sec it executes the function repeatedly X 2 The appropriate icon is displays on the screen
64. The invisible hand for more convenient world sensors amp controllers Au TONICS Sensors amp Controllers 100mm Hybrid Recorder KRN100 Series USER MANUAL RID RECORDER mm DORE SRE 096 6 C 834 O c 1071 4 c 1308 8 c KRN100 Series Thank you very much for selecting Autonics products For your safety please read the following before using Autonics ii Copyright Reserved Autonics Co Ltd Autonics Preface i Preface Thank you very much for selecting Autonics products Please familiarize yourself with the information contained in the Safety Precautions section before using this product This user manual contains information about the product and its proper use and should be kept in a place where it will be easy to access O Copyright Reserved Autonics Co Ltd iii i User Manual Guide Autonics User Manual Guide This user manual contains information about the product and its proper use and should be kept in a place where it will be easy to access Please familiarize yourself with the information in this manual before using the product This manual provides detailed information on the product s features It does not offer any guarantee concerning matters beyond the scope of this manual This manual may not be edited or reproduced in either part or whole without permission A user manual is provided as part of the product package Visit our home pa
65. Time Protocol ASde5 Com Write Ethernet Port ste Set whether using Ethernet communication If you set Ethernet Port as Enable RS485 Port is changed as Disable automatically Set range Enable Disable Factory default Disable Note You can monitor or set parameter KRN 100 with DAQMaster or the related Modbus program Modbus Poll etc For more information refer to KRN 100 user manual for communication Modbus TCP communication The following is based on Windows XP Ist First of all connect Ethernet slot of KRN 100 communication output card KRN COM and LAN slot of PC with LAN cable Communication output card KRN COM Ethernet port LAN Cable 2nd Execute Start gt Run to check IP address of PC me om vw Help and Support o je Run un Log OFF Autonics Z Turn OFF Computer Copyright Reserved Autonics Co Ltd 93 i 8 Parameter detail setup Autonics 3rd Enter ipconfig at Open in Run dialog box and you can check IP address of PC Type the name of program Folder document or Le Internet resource and Windows will open it For you Open ipconfig ww o C WINDOWS system32 ipconfig exe Windows IP Configuration Ethernet adapter Local Area Connection Connection specific DNS Suffix IP Address 2 2 2 2 Subnet Mask 255 255 2558 Default Gateway 192 168 6 1
66. V DC Alarm transistor NPN Open Collector 12 24VDC 30mA Max output er power Power output for 24 2VDC total 3 channel max 30mAper 1 channel Display Transmitt output transmitter built in over current protection circuit Modbus RTU RS485 Commu Recommended to use shield cable over AWG24 nication Ethernet IEEE802 3 U 10 100 BASE T Modbus TCP output USB Device 4 card USB V2 0 Full Speed Device Control x 1 To change input specification you must turn OFF the power of KRN100 remove universal input card set inner jumper pin Please refer to 4 2 I O card and re connect it Copyright Reserved Autonics Co Ltd 23 i 2 Specification Autonics X 2 Exception range for better accuracy by sensor Accuracy after 30min warm up time R S C G O lt T lt 100 4 0C B No regulation accuracy below 400 C T U 200 lt T lt 100 43 0C 100 lt T lt 400 2 0C Cu50 200 lt T lt 200 1 0C DPt50 200 lt T lt 500 1 5C X 3 RS485 Ethernet communication output are not available at the same time X 4 The front USB Device only for data backup and rear USB device is available only for parameter setting X It is recommended to use shield cable to decrease noise when sensor input cable is longer A Caution If connecting or disconnecting input output card when power is ON it may cause malfunction To connect or disconnect input output card you must turn OFF the power 24 Copyright Reserved
67. ail setup Autonics 1 Difference Deviation It is available to set when Input Type input specification is temperature sensor thermocouple RTD It displays the deviation of Reference Channel Reference channel measuring value Display standard channel measuring value reference channel measuring value Standard channel measuring valve Reference channel measuring valve Display value p e The set channel as analog current voltage of Input Type Input specification is not able to set as Reference Channel reference channel e If there is no set reference channel it displays standard channel measuring value e If any one of reference channel or standard channel is break BURN upper limit value HHHH lower limit value LLLL status it displays as correspond value If you select the channel which is used Difference function as reference channel it displays the value based on calculating actual measuring value not display value of reference channel 2 Linear It applies lower limit scale and upper limit scale to lower limit input value and upper limit input value and displays this values In case lower limit input value 5V Upper limit input value 5V and in case lower limit scale 1000 upper limit scale 1000 if current input value is 2V display value is 400 Display value Input value Lower limit input value x Upper limit scale Low
68. ain airplane combustion apparatus safety device crime disaster prevention equipment etc which may cause damages to human life or property it is required to install fail safe device lt may cause a fire human injury or property loss It must be mounted on panel It may cause electric shock Do not connect inspect or repair this unit when power is ON It may cause electric shock Check input power specification and check power terminal number when wiring power cable It may cause a fire or damage by a fire Lithium battery is used in this product do not disassemble or burn up this unit It may cause an explosion Do not touch the product or connect terminal within 30 sec after turn off the power It may cause electric shock F G terminal should be isolation grounded Grounded wire should be over AWG16 1 25 mm It may cause electric shock Do not insert your finger or object into the vent of this unit lt may cause electric shock or human injury Do not disassemble or modify this unit Please contact us if it is required lt may cause a fire human injury or property loss A Caution This unit shall not be used outdoors It may shorten the life cycle of the product or cause electric shock When wiring power input terminal and measuring input terminal power line should be over AWG 20 0 50mm Terminal screw should be tightened with 0 74 Nem to 0 90 Nem torque Please observe the rated specifications It may caus
69. ame Channel name name None 1 to 6 characters to 6 characters CH 1to12 Input Type Input specification pe ooo to detail descriptions Range Scale Point Decimal point Display Temp Unit Display unit Temperature unit High Low Range amp Graph Scale Upper Lower limit input value and graph scale value Low Scale High Scale Lower limit Upper limit scale value Special Function Special function Two Unit Display the degree of a vacuum static pressure Reference Channel Reference channel U Wu OC sopy right Reserved A Analog 0 0 0 0 00 0 000 0 0000 If special function is two unit 0 0 0 0 00 TC RTD C F K Analog Refer to detail descriptions Low Input range Min graph scale value to upper limit input value Graph scale value High Range Graph Scale F S 5 High Lower limit input value Graph scale value Low Range Graph Scale F S 5 to input range Max graph scale value Low Set the range by set value of scale point BI High Set the range by set value of scale point ES TC RTD None Difference None Analog Linear Square Root Two Unit 1 to 35 None CH J S UH Activates connected universal input 2 channel per one card i 8 Parameter detail setup Autonics Input Bias Error correction 999 9 to 999 9 CS Span Gradient adjustment 0 100 to 5 000 BE Record Method Data storage method Instant Average Minimum Maximum
70. ameter detail setup Autonics 8 5 1 Record Mode Recode mode LIM 123456 789 0A lues 22 37 a RECORD SETUP E NAME gt YALUE gt Record Mode Digital Print Type OneCH standard speed Anim h Option Speed 2 Anna Memo Period Ihaur re Set record mode to record display value on recording paper KRN100 supports Graph and Digital record modes 1 Graph Records display value as graph type on recording paper It records current time hh mm ss display value by channel in set Memo Period Digital memo record period DH 11 06 16 AL 13 10 00 DH r 11 06 16 AL 12 10 00 00000000 2 Digital Records display value as numeric on recording paper It records current time hh mm ss display value by channel in set Standard Period Print Record period and also records current date Year Month Day and time in every 00 00 00 You can record digital memo manually by front key press key for 3 sec or digital input terminal ot CHANGE DAY 11 06 1600 00 00 S CH 1 125 5 CH 2 203 3 o L O IcH 3 320 2 gt PL CH 4 512 6 o 41 06 16 OE Records every 00 00 00 o CH 5 452 1 CH 6 825 0 Cc AL 00 10 00 gt S is summer time O 4 CHANGE DAY 11 06 15 00 00 00 S o CH 1 125 5 CH 2 203 3 c DH CH 3 3202 T CH 4 512 6 0 11 06 15 O CH 5 452 4 AL CH 6 825 0 AL M23 50 00 oe e Digital memo Manual O
71. andard Speed Amm h standard Speed Option Speed Amm h Option Speed Hemo Period Hemo Period Pl 11 tdi LE Pl 11 tdi So Designate option record speed Recorder speed is indicated as feed length of recording paper per an hour mm h and it is activated only when Record Mode Record mode is set as Graph Graph After setting DI Type Select digital input 1 as Speed select either Standard Speed standard record speed Option Speed option record speed by digital input When changing the set value of Standard Speed Standard record speed the set value of Option Speed Pption record speed is also changed as same as the set value of Standard Speed Option Speed should not be lower than Standard Speed Set range 10 20 40 60 120 240 mm h Factory default 20mm h 100 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 5 5 Memo Period Digital memo period le Ma 123456 7890 Lu el Ma 123456 7890 Luis RECORD SETUP i FECORD SETUP NAME gt VALUE NAME gt Record Mode Graph Record Mode Digital Print Tyre OneCH Digital Print Tyre Standard Speed 2 Ann h Standard Speed Option Speed Amm h Option Speed 16hour Memo Period Memo Period hour Pl 1 tri Eat far Pl 11 tri mate Designate record period unit min for digital memo current time current value by channel Digital memo time is recorded at right time You can record digital memo manually by pressing key for 3 s
72. aying 72X64 Large unit How to register user unit image Ist Make 3 sizes images file type bmp using image tools 2nd Double click the arrow area as below figure and select the desired image files Download KRN100 User Image User Unit Position woo SmallUnit 32x10 Middle Unitf32x121 Big Unit 72x64 m h Image Data Download Status Look in 1e Desktop gt GF BES 91x28 B My Documents 4 My Computer My Recent Guy Network Places Documents CDKRN100_USB Serial Drivers Na Alb Nc File name E My Nemo Files of type Bitmap File bmp 138 Copyright Reserved Autonics Co Ltd Autonics 9 DAQMaster 3rd Select image files by type and size click Download to download user images Download KRN100 User Image User Unit Position Small Unit 32x10 serg mith Middle Unitf32x121 mah Big Uniti 72x64 m h Data Download Status 9 3 3 Boot logo image setting You can set boot logo image to display during KRN100 booting After making 320x120 size image with image tools and download it Download KRNTOO User Image Autonics Sensors amp Controllers KANT OO Po Copyright Reserved Autonics Co Ltd 139 i 9 DAQMaster Autonics 9 3 4 Backup data checking function This function is output downloaded backup data by DAQMater or an USB memory Ist Execute Data Anal At taskbar click Start Program DAQMaster DataAnal or at
73. below figure Press OK E key or Cancel BE key DISPLAY e Cancel Moves to upper parameter after not saving the setting e OK Moves to upper parameter after saving the setting 1234566910 E INPUT SETUP ALARM SETUP DIGITAL INPUT SETUP COMMUNICATION SETUP RECORD SETUP SYSTEM SETUP ot 5 FILE MEMORY SETUP E HE Pk Hl kd Copyright Reserved Autonics Co Ltd 49 i 7 Operation Autonics 7 3 2 Parameter RUN mode AT 3 sec X Dot parameters may or may not appear depending on the other parameter setting INPUT SETUP D ALARM SETUP DIGITAL INPUT ea COMMUNICATION FEED SETUP SETUP input setting alarm setting GEES digital input setting VIE com setting Select UI Card Select Ul Channel Select DI Card universal input card universal input digital input card preg select select select Input Set Copy Alarm Set Copy DI Type input parameter copy alarm digital input select copy parameter RS485 Port RS485 com use LCD Paper Record display and record measuring value Alarm type alarm operation Baud Rate DI _ Reset No i com speed reset alarm number mode Alarm Ref Channel me Pen Color alarm reference DIL Status Parity Bit record color i channel 1 operation status i com parity bit Alarm Option alarm option Stop Bit Record Zone com stop bit record zone Termination Set terminating resistance
74. com tr HM USA Autonics USA Inc Tel 1 847 680 8160 Fax 1 847 680 8155 E mail sales autonicsusa net E Vietnam Autonics Vietnam Representative Office Tel 84 8 3771 2662 Fax 84 8 3771 2663 E mail vietnam autonics com AEP E 0120A 20130911
75. d zone division 103 8 5 7 Standard Period Standard record period cccceecccseeeeceeeeeeeeeeeeeeees 104 8 5 8 Option Period Option record period 104 8 5 9 Listing Language Language for list output 105 8 5 10 Alarm Speed Alarm record speed 106 8 5 11 Power On Status Record status when power ON 106 8 5 12 Run Status List printing at start recording 107 8 5 13 List Out Option List record option 108 8 5 14 Zone Dot Line Distance Dot line for zone division 109 8 5 15 CH Print Distance Record interval for each channel graph 109 8 5 16 Start Line Print Start line when starting record 110 8 5 17 Range Print Time Input range record period rrrarrrrrnnnrrnnnnrrnnnnnnnnnenn 110 8 6 SYSTEM SETUP System setting 111 8 6 1 Device Name Device name 112 8 6 2 Date Time Date Time ss 112 8 6 3 Date Type Date type 112 8 6 4 Summer Time Summer time 113 8 6 5 Summer Time Period Summer time period rrrnrrrnrnnnrrerrnnnnrevrnnnrennnnn 113 8 6 6 Reservation Type Reservation record cccceecccceeeeeseeeeesseeeeeeeeesaeees 114 8 6 7 Reservation Period Reservation record period 115 8 6 8 Reservation Time Reservation record time ccccecceseeeceeeeeeeeeeeeeaes 115 8 6 9 Alarm Sound Alarm sound 116 8 6 10 Sampling Rate Sampling period
76. dk i on LL Flat head screwdriver L i No L EE as Rza U 2nd Insert I O card to the proper slot and turn ON the power of KRN100 E NSSS SS I O card Copyright Reserved Autonics Co Ltd 33 5 Installation Autonics 5 3 USB to Serial driver Install USB to serial driver which is applied for KRN100 sereis and connect DAQMaster and you can set parameter setting It is available only when communication output card KRN COM is connected Supporing OS for USB to Serial driver is Windows XP 32 64bit Windows 7 32 64bit 5 3 1 Driver installation Ist Visit our homepage www autonics com and downlaod KRN100 USB Serial Drivers Unzip this file to the desired folder 2nd Connect KRN100 USB port of communication output card KRN COM and PC USB port with USB cable A Mini 5P 1 5m EE sor output card KRN100 COM USB port USB A mini 5P cable 1 5m 3rd Found New Hardware Wizard appears Select Install from a list or specific location Advanced and click Next gt Welcome to the Found New Hardware Wizard This wizard helps you install software for KAN TOO USB to Serial If pour hardware came with an installation CD 32 or floppy disk insert it now What do yo
77. dld Heh AYnkld Ben Reservation Type Repeat Pesel Start Time Reservation Period 2HAAkyAlnAld 2Ad3v1 imad End Time Reservation Time AAhkAnb s K hAknAks Alarm sound OFF Designate reservation record time When Reservation Type Reservation record is set as Repeat Repeat ON OFF or Single Single ON OFF it is activated to designate Start Time Start time and End Time End time Set range 0 00 00 to 23 59 59 Factory default Note If reservation record Reservation record is set and during reservation recording digital input is not available as RUN mode In stopping recording status by reservation record it is available Copyright Reserved Autonics Co Ltd 115 g I 8 Parameter detail setup Autonics 8 6 9 Alarm Sound Alarm sound STSTEM SETUP NAME gt VALUE summer Time Period HEmald AAR AYp ld ARR DRETARA med 22045050 a Reservation Type Repeat Reservation Period lt H8dv41mdld 2443 11m24d Reservation Time AAhdAma s 22h mdds Alarm Sound Designate Alarm Sound alarm sound level when alarm operation turns ON Setrange OFF Min Standard Max Factory default OFF 8 6 10 Sampling Rate Sampling period mi Pin M2345 BPA M NE wed 22 40 23 a SV STEM SETUP HAME gt VALUE gt Reservation Type Repeat Reservation Period lt H8dv41mdld 2Ad3y 1m24d Reservation Time HAhhhmihs 22 hA NAAS Alarm Sound OFF sampling Rate Designat
78. does not operate normally Therefore please take proper measure to prevent malfunction of KRN100 system before starting firmware upgrade After completing firmware upgrade you must turn OFF and ON the power of KRN100 to operate normally In process of firmware upgrade when power turns OFF firmware upgrade is not complete When power turns ON again KRN100 operates with previous firmware version Try firmware upgrade again After completing firmware upgrade and OFF ON the power if KRN100 displays booting screen and does not operate normally it may have damage to the inner firmware during firmware upgrade It is required to repair Please contact our service center Autonics service center 82 32 820 2343 Copyright Reserved Autonics Co Ltd 129 I 8 Parameter detail setup Autonics 8 9 RECORD BACKUP SETUP Backup data record setting Record Backup creates file when power ON regardless of starting stopping record and saves the data to inner system memory An USB memory storage is available Enable by the set according the set record mode This parameter is useful to print the desired time data with backup data or check data by computer with DAQMaster dedicated software Therefore backup data set function is for printing the saved backup data at inner system memory and an USB memory Move to RECORD BACKUP SETUP with KB E keys press key to enter RECORD BACKUP SETUP BORA 8 2345678900 AE EE DIGITAL nr SETUP RECORD BA
79. e sampling rate Sampling period of measuring value Set range may be different by the number of connected universal input card KRN UI6 Setrange When connecting 1 to 2 universal input card KRN UI2 25 125 250ms When connecting 3 to 6 universal input card KRN UI2 125 lt 250ms Factory default 125ms Note Min sampling period for TC R U S T sensors is 50ms 116 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 6 11 Log Speed Save period fe f den 23456789 NMSNEN med 22443151 a SYSTEM SETUP NAME gt VALUE Reservation Period 2AAAyAlnAld 2943 11m28d Reservation Time AAhABNAksS 22 hA NAAS Alarm Sound OFF sameling Rate 120m5 Log speed Designate the save period of measured data by universal input card KRN UI2 to system memory The recorded data on recording paper is also recorded by save period For example 3 sec save period records every 3 sec data but it does not record during 3 sec of data which are changed Set range 0 to 3600 Factory default 1s Note If save period is set longer the relation between graph data and alarm ON data is lower because of the occuring alarm record in the middle of save period during recording When setting as Os for Log Speed save period recording operates normally but the data does not saved at inner external memory If no recording paper P END alarm occurs there is no designated data and backup data is not rec
80. e shorten the life cycle of the product and cause a fire Copyright Reserved Autonics Co Ltd Autonics Safety Precautions i Do not use the load over the rated switch capacity value of relay contact part It may cause insulation failure contact melt contact failure relay broken fire etc When connecting magnet contact as load of relay contact output connect surge absorber on coil part of contact It may cause malfunction In cleaning the unit do not use water or organic solvent And use dry cloth It may cause electric shock or a fire Do not use this unit in place where there is flammable explosive gas humidity direct light radiant heat vibration or impact lt may cause a fire or explosion Do not inflow dust or wire dregs into the unit lt may cause a fire or malfunction Wire properly after checking the terminal polarity It may cause a fire or explosion Wire properly after checking the terminal polarity when connecting temperature sensor It may cause malfunction Connection should be followed as connection diagram of this manual Before power ON check the connection correct It may cause a fire Do not touch terminal during dielectric or insulation resistance test It may cause electric shock It is recommended to use insulation transformer and noise filter power in case of too much noise from power Attach noise filter on the grounded panel etc Wire between noise fil
81. ec or using digital input terminal DI 2 Set range Recording record speed and record channel set range of digital memo period is limited Factory default 2hour If digital memo period is set as 60 min and record start time is 09 20 first record time is 10 00 not 10 20 Digital record time is 10 00 11 00 12 00 13 00 record end time If digital memo period is set as 10 min and record start time is 09 23 first record time is 09 30 not 09 33 Digital record time is 09 30 09 40 09 50 10 00 record end time Note Depending on record speed and the number of record channels memo period setting time is limited Record speed unit mm h Digital memo period setting time when record channel is 1 to 2CH E pe pe Jon fo dd owe up ron Digital memo period setting time when record channel is 3 to 4CH sat inn ue Pons nfs fe ie fr Jw fiw arr X x X wo Copyright Reserved Autonics Co Ltd 101 8 Parameter detail setup Autonics Digital memo period setting time when record channel is 5 to 6CH fo fom Jon one ae fe ue Pror ou re pur Digital memo period setting time when record channel is 7 to 8CH SE poe fo ow one ae eus pre ru Pw oro Digital memo period setting time when record channel is 9 to 10CH Digital memo period setting time when record channel is 11 to 12CH 102 Copyright Reserved Autonics Co Ltd
82. ed data of system memory as data backup function when run out of recording paper KRN 100 improves convenience by parameter setting data transmittion through RS485 and Ethernet communication USB device is only for parameter setting and backup data logger function It also adopts slot type input output card to connect option card up to 12 channels It supports several communication types of course and graphic user interface GUI with graphic display for easire and convenient use Combines functions of paper recorder and paperless recorder Enables to print the saved data of inner memory when run out of recording paper Data logger function Inner data backup with an USB memory High legibility and setting convenient by graph LCD 25ms high sampling 240mm h high speed record function 100mm paper record Selectable 6 kinds of record color Supports system memory and external memory data backup storage Supports several input up to 12 channel with slot type input card Enables to select several option card with slot type output card Supports several communication RS485 Ethernet to transfer real time data Enables to set parameter with USB DeviceX1 Space saving for installation with compact design Rear length 168mm Supports total 27 kinds of input sensor Enables to order several type input card weight voltage current frequency potential meter etc Copyright Reserved Autonics Co L
83. eding recording paper Backup data print icon Flashes during backup data printing Digital mode icon Marks it for digital record mode Graph mode icon Marks it for graph record mode Record memory status Marks it storage capacity of record memory in icon digital mode or graph mode No recording paper Marks it for no recording paper Please replace icon 1 new recording paper 38 Copyright Reserved Autonics Co Ltd Autonics 6 Display Name Desorption USB communication Marks icon during Modbus RTU icon communication using USB Ethernet Marks l icon during ModBus TCP communication using Ethernet RS485 communication Marks ek icon during Modbus RTU communication using RS485 Marks the below icon according to input function Digital input DI icon Digital input DI memo Marks it when digital memo of digital input or front is input in recording status Digital input DI alarm Marks it when alarm reset signal of digital input Digital input DI start Marks it when start record signal of digital input Digital input Dl stop Marks it when stop record signal of digital input Digital input DI LIST Marks it when LIST output signal of digital input Digital input Dl record Marks it when changing record speed signal of Marks it for unlock status User general user lock Marks it for user general user lock status icon Marks it for administrator and general user lock Administrator loc
84. ensor is 50ms Recording period in 10 20 40 60 120 240mm h graph mode 1 to 3 600 sec Storage period Storage interval time to inner log file is 1 sec User purchased recognizes max 32GB USB memory enables to use cable up to 1 5m Record color Record zone Input special function Input digital filter Function Reservation set Summer time Delay alarm Record speed change Data storage Backup data record etc 2 500VAC 50 60Hz for 1 min power terminal and case Dielectric X USB Device and Ethernet are excepted Vibration strength Vibration strength 10 to 60Hz 4 9m s2 in X Y Z axes for each 1time for convey and storage a Operating vibration 10 to 60 1m s in X Y Z axes for each 10 min and operating vibration Insulated resistance Min 20MQ at 500VDC megger 2KV the square wave noise pulse width 1us by the noise simulator Within 2min year Enables to use up to 2100 year Ink Enables to normal print with going and returning printing max 5 times Mechanism cartridge within 7 days after opening the unit Copyright Reserved Autonics Co Ltd 21 2 Specification Autonics 22 Ink dry Max 15 minutes time Recording paper 113mm X 9m It shall be used indoor Altitude Max 2 000m Pollution Degree2 Installation environment Installation category Il Temperat gt 0 to 50 C Storage 20 to 60 C without ink cartridge ure Environ 35 to 85 RH Storage 35 to
85. er Lock mY x 2 Space al Le bse EE Ge 1 LL mim mim A RIS ig aG Change the previous password Changing password is able only when login status as administrator Set range 4 digit number Factory default 126 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 8 4 User Lock Change user authority ml PP ON 23456789 0M Mens USERTMFORMATION SETUP Admin Model a WALUE gt Password Enable NAME gt Login Admin Change Admin Password GK User Lock Information Display Er Cu fo fan LA Ris te User general user mode has three levels for function set authority Setable parameter by function set authority is as below Lock1 Lock2 DIGITAL INPUT ALARM SETUP INPUT SETUP RECORD SETUP SYSTEM SETUP i COMMUNICATION SETUP RECORD BACKUP DATA FILEMEMORY SETUP Enables to check and change set value A Enables to check set value X Disable to check and change set value Set range OFF LOCK1 LOCK2 LOCK3 Factory default OFF 2 Note Regardless of User Lock change user authority setting User general user mode cannot change firmware upgrade the set file initialize password mode disable functions 8 8 5 Information Check system information mfe You 2345678900 AMM lues casses a USERINFORMATION SETUP Admin Model cf fal Ym Sl 234567890 ie Me era c lt INFORMATION SETUP gt gt ae NAME gt VALUE
86. er limit scale Upper limit input value Lower limit input value Lower limit scale 7 400 x 2000 1000 10 3 Root In case voltage current input type this mode is used when input value is calculated by Root V for the desired display value Differential pressure signal of differential pressure flow meter is calculated Root V for the to be measured flux This function is used to measure flux by input value In case lower limit input value 5V upper limit input value 5V and in case lower limit scale 1000 upper limit scale 1000 if current input value is 2V display value is approx 673 32 Display value Input value Lower limit input value ae a EX Upper limit scale Lower limit scale Upper limit input value Lower limit input value Lower limit scale 7 673 32 10 X 2000 1000 64 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup i 4 Square In case of voltage current input type this mode is used when input value is calculated by square for the desired display value Reverse of Root flux signal is calculated by square for differential pressure signal In case lower limit range 5V upper limit range 5V and in case lower limit scale 1000 upper limit scale 1000 if current input value is 2V display value is 20 Display value Input value Lower limit input value Upper limit input value Lower limit input value x Upper limit
87. error by electric potential of between ground during long distance communication For using terminating resistance turn ON only terminal resistance of recoder on end of connected communication line Enables to set using terminating resistance in communication set function and also turn ON terminal resistance of connected communication to PC Copyright Reserved Autonics Co Ltd 89 I 8 Parameter detail setup Autonics 8 4 1 Modbus Address Communication address mle Fi S1234567890NAAEN ue 22 23 ar COMMUNICATION SETUP a MAME gt Modbus Address Rsd Port Baud Rate Parity Bit atop Bit Designate communication address The designated communication address is able to apply to RS485 USB Device also Ethernet communication However duplicated communication address setting in same communication line does not allow Set range 1 to 127 Factory default 1 8 4 2 RS485 Port Use RS485 communication le fm dl 23256789 URAN med 22 25 88 F COMMUNICATION SETUP NAME gt VALUE gt Modbus Address 1 Ragas Port Baud Rate EAA Parity Bit Hone atop Bit 2 Set whether using RS485 communication If you set RS485 Ports set value as Enable Ethernet Port s set value is changed Disable automatically Set range Enable Disable Factory default Enable 8 4 3 Baud Rate Baud rate fe E SASE TEONA med 22 sa aa a COMMUNICATION SETUP NAME gt Modbus Address Rsd Port Baud Rate
88. et range is 200 0 to 1272 5 C e Factory default 200 0 Copyright Reserved Autonics Co Ltd 59 i 8 Parameter detail setup Autonics 4 High Graph Scale Upper limit graph scale value Den 2 a asser etais LC ke 923456789000 rm rr tar 15 5 INPUT SETUP RESTE a mlilslc olelrlel nput Tyre Meet tiki EIRE ES Ranse Scale Point a mole tatals riul 7 el al Low Graph Scale 200 i aap bel EG High Graph Scale Within the input range of Input Type Input specification set upper limit graph scale value nee does not displayed in analog input type Set range Lower limit graph scale value Low Graph Scale F S 5 to Max value of input range When TC K input range is 200 0 to 1350 C set range is 122 5 to 1350 C e Factory default 1350 0 60 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup i 8 1 11 Low Scale High Scale Lower limit Upper limit scale value This function is for set the desired display value based on measuring value It is applied to analog voltage current input type only As below figure for example measuring input value are a and b and the desired display value are A and B In this case about the input a and b it displays a A b B as linearly A B ea steam no ne se ni B Display Display B Display value value value lt a P i a b A Input value D Display lt a
89. eters from external upper system PC and graph panel etc or transmitting the data to external devices by RS485 Ethernet or USB Device communication It is recommended to use our dedicated software program DAQMaster for monitoring If you want to develop monitoring program not using our DAQMaster program or to use the related Modbus program please refer to user manual for communication Visit our homepage www autonics com to download DAQMaster program and user manual for communication Move to COMMUNICATION SETUP with KE keys press key to enter COMMUNICATION SETUP D 012345678008 LS les Le Bd 823456 789 02 wed 15 47 12 E la Hi D COMMUNICATION SETUP lt NAME gt lt VALUE RS485 Port Address Baud Rate SAHA Parity Bit Hane Stop Bit 2 m Parameter list Parity Bit Communication parity bit Stop Bit Communication stop bit o Wait Time Communication response wait Protocol Communication protocol RS485 Com Write RS485 communication write Ethernet Port Use Ethernet communication Default Gateway Default gateway 0 0 0 0 to 255 255 255 255 Ethernet Com Write Ethernet communication write Enable Disable USB Device Port Use USB communication USB Com Write USB communication write G Note KRN100 does not supports RS485 port Ethernet port at the same time for preventing system overload If you change one as Enable the other is changed Disable automatically In case USB Device it is able t
90. evice name le 0234568901 ek bees 8 STSTEM SETUP NAME gt VALUE Device Name KRNIAR Recorder Date Time 2A11A6 15 Wedd 22 44 34 Date Type Ti dd summer Time Disable SUNNE Time Period aa Designate user defined KRN100 name lt supports up to 16 characeters with English capital letters English small letters and special letter Set range 16 characters Factory default KRN100 Recorder 8 6 2 Date Time Date Time 04 Mu bl 23456 EET Fl med 22540 ml Po 234567800185 ut D SYSTEM SETUP Se SYSTEM SETUP NAME gt VALUE gt diket Date Time Device Hame KAN TAR Recorder Date Time BEITE aT Ene Cee Date Ei 67 15 Date Type Tim dd Time gr dh 53 summer Time Disable Summer Time Period Er Desigante system date and time of KRN 100 When you set the date the day of week is automatically set and time is displayed in 24 hours format Based on set date and time it records and saves the data Setrange Date 2000y01m01d to 2099y12m31d Time 00h00m00s to 23h59m59s Factory default Set as factory default 8 6 3 Date Type Date type fe Fm RAA med 22441107 a SYSTEM SETUP NAME gt VALUE Device Ham KAN TAR Recorder E Date Time SUC a aa di Af Date Type eal dd summer Time SUNNEFr Time Period Set KRN100 system date display method on the screen and record method on the recording paper You can select one display method among yyyy year mm month dd day mm month dd day yy year
91. flashes When there is parameter setting error card recognition error etc this error message flashes twice and KRN100 returns to previous screen m Eo 23456780 MAAE f re sat ea sa 20 KAW TBA Message Inner Memory Internal Memory 0 error Check or Reboot I CHE Access As above screen if excess error message for inner system memory Read Write occurs frequently please contact our service center 150 Copyright Reserved Autonics Co Ltd Autonics 11 Troubleshooting i O Copyright Reserved Autonics Co Ltd 151 Autonics Sensors amp Controllers Distributor E Major products Photoelectric sensors Fiber optic sensors Door sensors Door side sensors Area sensors Proximity sensors Pressure sensors Rotary encoders Connectors Sockets Temperature controllers Temperature Humidity transducers SSR Power controllers Counters Timers Panel meters Tachometer Pulse Rate meters Display units Sensor controllers Switching mode power supplies Control switches Lamps Buzzers I O Terminal Blocks amp Cables Stepper motors drivers motion controllers Graphic Logic panels Field network devices Laser marking system Fiber CO Nd YAG Laser welding soldering system Recorders Indicators Converters Controllers Thyristor units Pressure transmitters Temperature transmitters E Any proposal for a product improvement and development Product Gautonics com
92. fo P 23456 BSA we 22 35 28 a COMMUNICATION SETUP NAME gt VALUE gt IP Address 192 168 1 2 subnet Mask 269 295 255 Default Gateway 192 168 1 Ethernet Com Write Enable USB Device Port Set whether using USBcommunication USB communication is available regardless of RS485 Port or Ethernet Port setting Set range Enable Disable Factory default Enable 8 4 16 USB Com Write USB communication write ml Po SM 25456 BAIT wep 22055031 a COMMUNICATION SETUP NAME gt VALUE gt subnet Mask 200 200 200 Default Gateway 192 168 1 Ethernet Com Write Enable USB Device Port Enable USB Com Write Set whether changing the set value of KRN100 parameter by USB communication To read the set value of each parameter is available regardless of the communication write enable disable setting Set range Enable Disable Factory default Enable 96 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 5 RECORD SETUP Record setting You can set record mode record speed record language and digital memo etc Depending on record mode Digital Graph below parameters are changed Move to RECORD SETUP with KE keys press key to enter RECORD SETUP 173456 78910010 719 f le Mu OM 23456 789 024 ler wet 155 2e te INPUT SETUP RECORD SETUP DIGITAL INPUT SETUP Record Mode COMMUNICATION SETUP Digital Print Type OneCH RECORD SETUP standard
93. g channel min set range is limited as below 01m 00s to 99m 59s 02m 00s to 99m 59s Factory default 8 5 8 Option Period Option record period Mon Sf 2345678902 fel 10 der s r r 123456789012 NeW 10 aaraa RECORD SETUP ae a H ANE gt VALUE gt LU Hemo Period Option Period Divide fone es Standard Period 2AnAAs Period Option Period ms Listing Language ri TU When Record Mode Record mode is set as Digital set record period for current time hh mm ss and measuring value by channel min sec through digital input Speed set Set range 00m 01s to 99m 59s Depending on the number of recording channel min set range is limited as below 01m 00s to 99m 59s 02m 00s to 99m 59s 03m 00s to 99m 59s Factory default 104 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 5 9 Listing Language Language for list output fe Fm SP 23456789 MAVEN med 22 36 11 a RECORD SETUP MAME gt Hemo Period Divide fone standard Period Option Period Listing Language rh TU O PRINT MODE DIGITAL 2011 06 14 THU 11 35 27 o SPEEDTSTANDARD 240 ALARM 240 OPTION 240mm H INPUT LO_RNG LO_SC UNIT TAG HILRNG HI_SC FILT English TC K 200 0 CH 1 1350 0 TC K 200 0 11 35 27 OSSI ES Secale BA 200 0 1350 0 200 0 0000000 Set range English Korea Factory default English Copyright Reserved Auto
94. ge www autonics com to download a copy The manual s content may vary depending on changes to the product s software and other unforeseen developments within Autonics and is subject to change without prior notice We contrived to describe this manual more easily and correctly However if there are any corrections or questions please notify us these on our homepage iv O Copyright Reserved Autonics Co Ltd Autonics User Manual Symbols i User Manual Symbols Symbol Description VG Note Supplementary information for a particular feature A Warning Failure to follow instructions can result in serious injury or death Caution Failure to follow instructions can lead to a minor injury or product damage EX An example of the concerned feature s use X1 Annotation mark O Copyright Reserved Autonics Co Ltd V i Safety Precautions Autonics Safety Precautions vi Following these safety precautions will ensure the safe and proper use of the product and help prevent accidents and minimize hazards Safety precautions are categorized as Warnings and Cautions as defined below Cases that may cause serious injury or fatal accident if instructions are not followed A Caution Cases that may cause minor injury or product damage if Caution instructions are not followed A Warning In case of using this unit with machinery Ex nuclear power control medical equipment ship vehicle tr
95. gh Scale Upper limit scale value is 0 00 If changing gradient adjustment value as 0 500 1 000 or 1 500 display value by each changed gradient adjustment value is below Same wo 4000 foo fo 4000 oo 1000 10000000 wo 68 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup i Display value Gradient adjustment 8 1 16 Record Method Data storage method fe f den 8 23456789 02 14015 20 65 a INPUT SETUP CH1 31481 1 MAME gt Two Unit Reference Channel Input Bias Pan Record Method Set storage method for measured data by channel to inner external memory Display and print method is Record Method Instant Instant value Saves measuring value by every record period Log Speed Average Average value Saves averaged measuring value during record period Log Speed Minimum Min value Saves min measuring value during record period Log Speed Maximum Max value Saves max measuring value during record period Log Speed Set range Instant Average Minimum Maximum Factory default Instant 8 1 17 Filter Type Input digital filter me f den 923456 789 00 eA VE an rue 17224 ta a INPUT SETUP CHi S1UI 1 NAME gt VALUE gt SPAM 1 ABH Record Method Instant Filter Type Filter Counter Burnout Action In some applications the fluctuating measuring input causes the display value to fluctuate In this case accurate display record
96. gnized on USERINFORMATION SETUP Firmware Upgrade menu fe Pm SP 23456789 Olea mo 16122126 a USERINFORMATION SETUP User Mo K 3 NAME gt Login Admin Change Admin Password User Lock Information Firmware Update 1201104216 Mew 4th Check currrent version s date and to be upgraded version s date Select Upgrade button and it starts firmware upgrade CIRR E 23456789 Olea 14018 23236 a USER KANTAA Upgrade gt Current Version VERT 1AA Upgrade Version 24114214 Cancel Upgrade Before processing warning message appears Select OK ml Pa Wi 25456789 e Tr s EENID pan Marrning 1112 System is Stor and Upgrade Start o Ce EEE kd 128 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 5th After completing firmware upgrade below message appears Turn OFF the power and turn ON it again a kia Sf 23456 789 AM ETE KRNTB Message gt Warning 111 gt Upgrade Success Plase Reboot 6th At first booting after upgrade initialize and delete every parameter set file Inner default set file User1 pms to User5 pms to consider firmware version information print and compatibility with previous parameter setting 234961091011 KAN THA Firmware Update Success vB THe 1 gt Warrning gt Parameter is all Reset A Caution During firmware upgrade alarm output digital input and log file save etc functions
97. hardware devices installed a on your computer Use the Device Maqager to change the properties of any device Device Manager Drivers Driver Signing lets you make sure that installed drivers are compatible with Windows Windows Update lets you set up how Windows connects to Windows Update for drivers Hardware Profiles 2 Hardware profiles provide a way for you to set up and store different hardware configurations Hardware Profiles E2E3 Device Manager File Action View Help lt FO m F8 ET A lt A AUTONICS AS6DA v Computer sa Disk drives 32 Display adapters 2 DVD CD ROM drives gj Human Interface Devices IDE ATA ATAPI controllers 10 Keyboards Mice and other pointing devices H Monitors x BB Network adapters INY Ports COM amp LPT Sf Communications Port COM1 ommunications Po OM KRN100 USB To Serial Converter COM3 9 Printer Por L Processors Sound video and game controllers 2 System devices Universal Serial Bus controllers O Copyright Reserved Autonics Co Ltd Autonics 6 Display i 6 Display 6 1 Initial booting screen Below booting screens are initially displayed when power is supplied to KRN100 These screens progresses initial settings for KRN 100 to operate normally and checks inner system memory If there is no error for inner system memory booting is finished and KRN100 operates normally Screen for p
98. iginal backup data is saved as Digital mode Backup Print Mode displays digital To print with Graph mode Select Print Mode set as Graph Graph mode s record speed follows the set record speed of graph mode in current record setup How to select record backup file Ist Move to RECORD BACKUP SETUP parameter setting group DIGITAL SETUP COMMUNICATION SETUP RECORD SETUP SiSTEH SETUP FILEMEMORY SETUP USER INFORMATION SETUP RECORD BACKUP SETUP 2nd In Backup Data List press key and system memory and the saved backup data in USB are also display If backup data is not designated or does not exist it displays File Not Found A TP D E Eh rei 1e 25020 Ol FRE 23456 18901 mea Ro THU ta 22 26 RECORD BACKUP SETUP o MAME gt y Record Backup Backup Data List Sann 2 Internal 6 EFE lt USB Memory ih 1 15 KRM TAR 28181229 184287 USB Hot Found KRM TAR 7A181229175823 Start Date and Tine 2014 1229 19 42 47 End Date and Time 2414 1229 16 43 37 Backup Print Mode Graph KARM TAA 28181229 1 75544 KANT AA 281812291 75331 KANT AA 28142291 fod 3rd Select the desired file in Basckup Data List and press key and menu is displayed Marked files displays currently saving file om 2945678 910 Mn rai 18 05 26 Seem elete File File Infomation es lt lt Prey Page KRNIAA 2A1A1229 179 Next Page gt gt KRNIAA 2A181229 175 Up Directory KRNIAA 28141229 179 Into Directory KAN TAA 28191229 1798 ile Co
99. imal point In case Input Type Input specification is temperature sensor thermocouple RTD set wheter to display decimal point to measuring value In case analog voltage current set decimal point position of Low Scale Lower limit scalevalue High Scale Upper limit scale value Set range In case Input Type Input specification is temperature sensor thermocouple RTD 0 0 0 In case analog current voltage 0 0 0 0 00 0 000 0 0000 Factory default 0 0 YF Note If you want high accuracy display select 0 O decimal point If you want to stable accuracy display select 0 no dicimal point Copyright Reserved Autonics Co Ltd 57 I 8 Parameter detail setup Autonics 8 1 9 Display Temp Unit Display unit Temperature unit In case Input Type Input specification is temperature sensor thermocouple RTD temperature unit is activated In case analog current voltage display unit is actiaved le Mo 912345678901 oo med 25 39 00 INPUT SETUP CH3 S2U1 1 Fy NAME gt VALUE Tag Name Tasse LE INPUT SETUP Feks FI NAME gt Tag Name Input Type Ranae Scale Point Diselav Tene Unit Low Range CH Input Type TC Hange Scale Point H Display Teme Unit ee Low Hange 2 Ar Fr Setrange In case Input Type Input specification is temperature sensor thermocouple RTD C F K In case analog Refer to below table Factory default C Set range in case analog curren
100. int Mode Backup Set storage end date and time for backup data You can set end date and time Set range is within start date and time to end date and time Set range Date yyyy mm dd Time hh mm ss Factory default 0000 00 00 00 00 00 8 9 5 Backup Print Mode Backup data record mode da L on 923456 78902 l ueo 23 56 03 a RECORD BACKUP SETUP NAME gt VALUE Backup Data List KRMIAG 281 18615 225126 KAO start Date and Time 24008141 AR AR AA End Date and Time ARAB AA AR OG ai Backup Print Mode select Print Mode rach You can check record mode of current saved backup data 132 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup i 8 9 6 Select Print Mode Backup data recording mode setting Fe aN nn FREE fet ire RECORD BACKUP SETUP le MANE gt VALUE Backup Data List KEHI0d_201109615 27516 KAD Start Date and Time 2004 01 01 AR AR End Date and Time 2004 01 41 AR AR AA Backur Print Mode HET Select Print Mode It is able to print with different record mode from original backup data s record mode Set range Graph Digital Factory default Graph G Note To print with different record mode from original backup data s record mode it records with the set record speed in case record mode is Graph or the set record period in case record mode is set as Digital from record mode Digital or Graph on current record setup For example in case or
101. ion when alarm ON You can set up to 4 operations by each channel and alarm operations are as below Alarm set value 90 C If display value is same or a TE higher than alarm set value A A 907 PVI00C alarm output turns ON Alarm set value 90 C If display value is same or lower than alarm set value alarm output turns ON Alarm set value If the deviation between 10 C display value and the OFF y H TON display value of reference A PVT1OG Reference Reference PV 1000 channel is same or higher PV 110 channel PV 90 C than alarm set value alarm output turns ON If the deviation between Alarm set value Alarm set value 10 C display value and the display value of reference ON Hy OFF A channel is same or lower Reference PV 110 PV 90 C Reference channel channel PV 100 C By 100 than alarm set value alarm output turns ON In case input is not connected or input cable is break during controlling alarm output turns ON You can check whether input cable is break by external contact of alarm output using buzzer or other devices In case of no recording paper during recording record operation stops and this alarm output turns ON Measuring value is saved at system memory automatically Alarm is automatically cleared when recording paper is replaced in case of general alarm P END BACKUP PRINT window is activated and it is available to output backup data OR
102. is disable This function is able to make display value stable by input digital filter Input digital filter uses moving average method Moving Average Filter It does not affet to display period but display value may be different with input value Set range None Moving Factory default None Copyright Reserved Autonics Co Ltd 69 I 8 Parameter detail setup Autonics 8 1 18 Filter Counter The number of digital filter me f den I 23456 7890 LS we 17 27 53 FRUA a INPUT SETUP CH1 S1U1 1 YA NAME gt Record Method Filter Type Filter Counter Burnout Action Designate the number of sampling which apply to digital filter When you set Filter Type Input digital filter this parameter is activated Set range 1 to 128 Factory default When the set value of input digital filter is 4 it does moving average input sampling values for 0 1 sec 100ms and displays this value 25ms i S1 S2 S3 S4 55 56 S7 S8 S9 Sn Sampling value Di D2 D3 D4 D5 D6 D7 D8 Dn Display value D1 S1 S1 S2 S1 52 53 D2 7 eS 4 Display values of D1 D2 D3 is the initial operation before averaging 4 sampling values S1 S2 S3 S4 S2 S3 S4 S5 4 D5 4 4 S3 S4 S5 S6 S4 S5 S6 S7 6 p7 4 4 S5 S6 S7 S8 rn EE 70 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 1 19 Burnout Action Display setting for
103. ithin 10 of upper limit input range it is removed automatically Prints HH In case Input Type is temperature sensor thermocouple RTD if input value is lower than lower limit range this error message flashes If input value is within lower limit range it is removed automatically In case Input Type is analog current voltage if input value is lower than over 10 of lower limit input range this error message flashes If input value is within 10 of lower limit input range it is removed automatically Prints LL In case Input Type is analog current voltage if input value is higher than below 10 of upper limit input range _H is displayed with current value to notify that current value is higher than upper limit input range Ex When upper limit input range is 100 and current value is 102 it displays as 102_H In case Input Type is analog current voltage if input value is lower than below 10 of lower limit input range L is displayed with current value to notify that current value is lower than lower limit input range Ex When lower limit input range is 0 and current value is 1 it displays as 1_L If input is break this error message flashes When input is connected it is removed automatically Prints BH display value by break is High or BL display value by break is Low Refer to 8 1 19 Burnout Action Display setting for break If universal input card is not connected this error message
104. k icon a status setting during digital input DI Displays data capacity of internal memory as bar Inner and external graph When an USB memory is connected it USB memory capacity displays data capacity of an USB memory as bar icon graph If used memory capacity is over 90 of total capacity it flashes 2011 02 07 Displays current date and time In summer time MON 15 17 34 Date Time display season S mark is also displayed at front of year X 1 If there is no recording paper EN icon flashes After replacing recording paper P END BACKUP PRINT screen as below is activated i TT Backup data recording function by P END is same as RECORD BACKUP Backup Data List cannot be changed Copyright Reserved Autonics Co Ltd 39 5 Display Autonics me Bd OY 23456789 00 c ri ta aes 22 PEND BACKUP PRINT A Record Backup Stor Backup Data List KRMIAR2AIAGAY 144512 KRO Start Date and Time 2011 86 49 14 45 46 End Date and Time 2011 0649 14 46 50 Backup Print Mode Graph Starting print by P END Backup it prints the data but backup data file date file name and backup record starting line 40 Copyright Reserved Autonics Co Ltd Autonics 6 Display 6 2 2 Virtual keyboard You can enter set value with vertual keyboard Supports only English letters for entering character Virtual keyboard is activated when set value is input You can enter English letters
105. larmi Ret CH Hlarmi Option Alarmi Value Hlarmi Hysteresis n CIEL LL Set the interval between alarm output ON and OFF If PV is over or below alarm output SV output turns ON and it sets OFF time by hysteresis settings When input value is changed near SV alarm output is often Set hysteresis and it can be prevent from often alarm output Set range 0 0 to 9999 9 Decimal point position is different by the set decimal point position of input Factory default 0 0 The below graph is when Alarm Type Alarm operation mode is set as absolute value upper limit alarm Alarm Value Alarm 1 set value is set as 200 and Alarm Hysteresis Alarm hysteresis is set as 10 Temperature PV 200 C Alarmi hysteresis 190 C gt Time Alarm ON ouput OF dh kl Copyright Reserved Autonics Co Ltd 79 8 Parameter detail setup Autonics 8 2 8 80 Alarm ON OFF Delay Alarmi1 ON OFF output delay time alles ag nd bed PPO 23456 TOS A I rn 13 26 04 ALARM SETUP CHI S1UI 1 Fame ALARM SETUP CHI S1UI 1 te NAME gt MAME gt Alarm Option Alarm Oetion Alarm Value Alarmi Value Alarmi Hysteresis Alarm Hysteresis Alarmi ON Delay Alarm ON Delay Alarmi Off Delay Alarmi Off Delay Set delay time unit sec to prevent alarm malfunction by wrong input from external disturbance and noise Item Description gt Even after standby the set time when alarm ON condition alarm ON
106. m Ci FF mim Ci PT In case Input Type Input specification is temperature sensor thermocouple RTD set Special Function special function as Difference to set reference channel Set range None CHO S0OUI O Factory default 8 1 14 Input Bias Error correction me i SI 23456789 000 farm rue raea me ro 923456789010 AE mm io 18 46 INPUT SETUP CH1 S10I 1 E AE E mj ejc o E F c WE High Scale 198 9 DRE RS a A o rlafrfs rjul 7 8 a Reference Channel None ei Yl zl see fp ol Le This function is for error correction from input thermocouple RTD voltage current not from this recorder When temperature sensor cannot be installed near measured subject there may be the temperature deviation between temperature sensor area and measured subject area This function calculates and corrects this errors Several kinds of temperature sensor has specified grade High accuracy type is high price and ordinary product is generally used To correct input by measuring error from each helps more accurate temperature measurement For using this error correction function you should accurately measure the deviation from input part at first If this deviation is not correct the error may be higher Set range 9999 to 9999 999 9 to 999 9 99 99 to 99 99 9 999 to 9 999 lt gt 0 9999 to 0 9999 Depending on the set scale point range is different Factory default 0 0 In case actual temperature is 80
107. n List record option Even if you print the parameter set information with max record speed 240mm h it takes a lot of time It takes approx 40 minutes for 12 channels Be sure that for printing the list 3 Manual feed FEED In record STOP state press front key for over 3 sec record state icon is changed to FEED icon and you can feed recording paper manually To tear recording paper use this manual feed function at first 4 Digital memo Digital Memo Press for over 3 sec during recording status digital input icon changes to NE memo icon It records current time hh mm ss and display value of each channel as digital number on recording paper It also displays M which means the recording by memo at front of current time 48 Copyright Reserved Autonics Co Ltd Autonics 7 Operation i 7 3 Parameter setting group 7 3 1 Parameter setting The setting order of KRN100 basic parameters is as below For more information of detail setup of each parameter please refer to 8 Parameter detail setup SYSTEM INPUT ALARM DIGITAL INPUT SETUP SETUP gt SETUP gt SETUP COMMUNICATION ea RECORD es FILE MEMORY USER INFORMATION SETUP SETUP SETUP SETUP To enter parameter setting group Press key for 3 sec To move among setting group To move the setting a FEED J DISPLAY To move upper parameter after setting Press MM key and Function key is activated which is placed at bottom right as
108. ndby sequence or when current temperature is out of alarm operation range At the next alarm output ON alarm output operates normally Alarm Type AlarmL 1 operation mode PV Lo Absolute value lower limit alarm Alarm Value AlarmL set value 90 Alarm Hysteresis Alarm hysteresis 5 Alarm Option Alarm option StBy Standby sequence O Copyright Reserved Autonics Co Ltd 77 i 8 Parameter detail setup Autonics 8 2 6 78 Temperature ON renee eee feces a Power ON Hysteresis Alarm Value 90C a ae g No alarm output operation Time Alarm output operation lt When power is ON it is alarm condition and it is ignored From second alarm conditions it operates as standard alarm AlarmL Value AlarmL set value m Po 123456 rao Ae us ALARM SETUP gs HAME gt Alarm Set Copy CH Select Alarm Tyee PY Hi Alarmi Ret CH Alarni Option None DORE Space o le LL _ F F Set alarm set value based on alarm output operation mode it executes alarm operation Set range Using set input from Input Type Input specification within display range Factory default Alarm1 value 1350 0 Alarm2 Value to Alarm4 Value Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup i 8 2 7 Alarm Hysteresis Alarm hysteresis fe im S45 RTOS NANT med 22 26 54 a ALARM SETUP CH3 S2U1 1 NAME gt Alarm Tyee A
109. nected Device Tag Name 11 10 20 BE 4 3 Set Value 10 2 DAQ List R W Unit Present Value 3 Present Vale R c Set Yalue 3 Set Value Heating MV 3 Heating MY Cooling MY 3 Cooling MV R R R Heater Current M 3 Heater Current Monitoring R R R Note Visit our homepage www autonics com to download DAQMaster user manual This KRN 100 user manual describes only for dedicated KRN 100 functions For more information about DAQMaster please refer to DAQMaster user manual Copyright Reserved Autonics Co Ltd 135 i 9 DAQMaster Autonics 9 2 Features DAQMaster has the following features Supports multiple device DAQMaster is able to simultaneously monitor multiple devices and set parameters of the devices The units with different addresses in a single device are connectable at the same time In Modbus RTU communication several RS232 port are available Device scan In case multiple units with different addresses are connected together use unit scan function to automatically search for units Convenient user interface User can arrange windows attributes and project screens etc to monitor the data as convenient When saving the project set screen is also saved Project management You can save the setting of monitoring for added device and data selection of I O source etc as the project When loading the project this file has the saved setting status You can al
110. ng value display 44 Delo Ghane GVVING EEE 46 7 2 Special operation for record 48 T3 Parameter setting group iii 49 7 3 1 Parameter setting 49 132 PArAME LCR nn a eue re 50 8 Parameter detail setup hhv 53 8 1 INPUT SETUP INBUTSOtINQ eeseeoe 53 8 1 1 Select Ul Card Select universal input card 55 8 1 2 Input Set Copy Copy input parameter rrrnnnnnnnrrranernnnernnnevnnrrraennnnennn 55 8 1 3 LCD Paper Record Display and record measuring value 56 8 1 4 Pen Color Record COO ecrire aa ia 56 8 1 5 Record Zone Record zone 56 8 1 6 Tag Name Channel name 57 8 1 7 Input Type Input specification 0 0 0 cece cecccceeeeceeeeeeeeeseeeese essa eeeeeeeseeeenes 57 8 1 8 Range Scale Point Decimal point 57 8 1 9 Display Temp Unit Display unit Temperature unit 58 8 1 10 High Low Range amp Graph Scale Upper Lower limit input value and graph scale value 59 8 1 11 Low Scale High Scale Lower limit Upper limit scale value 61 8 1 12 Special Function Special function rrarernnrernnnernnrrranernarennanennnrnrnnennanennn 63 8 1 13 Reference Channel Reference channel 67 8 1 14 Input Bias Error correction 67 8 1 15 Span Gradient adjustment rrronnrrnrnnnrrrrrnnnrerrnnnrrrnnnnnrernnnnrrnrnnnnnnnnnnnnen 68 8 1 16 Record Method Data storage method 69 8 1 17 Filter Type Input digital filter
111. nics Co Ltd Autonics 8 Parameter detail setup i 8 1 6 Tag Name Channel name fel Ea 223456789018 lu sorted Ped bie 925456789011 le Hi io ta se INPUT SETUP CHA SSUT 1 le a mg Bee ee Input Set Copy 5 HJrfJ KJLYHPN 4 5 61 rn Color p gol rf alafsjrful frfelfe Record Zone Mg ll Jel Tag Name Designate channel name with virtual keyboard You can enter max 6 characters with English capital letters English small letters and speical characters Set range 1 to 6 characters Factory default CH 1 to CH 12 Channel number by slot E Note Some special character may be printed in low quality due to low print resolution 8 1 7 Input Type Input specification me io 23456789 0 wed EEE INPUT SETUP CHS S2UI 1 TC NAME gt VAL LCD Parer Record TC L Russia OK Pio S1234567890NAAET lues 22 16 44 INPUT SETUP CH5 SaUT 1 ae MAME gt LOO Parer Record Pen Color Record Zone Tag Hame Input Tyre Pen Color TC H Record one TC P Tag Name TE A Input Type Set input specification of channel Set input speicfication is total 27 such as thermocouple RTD voltage and current For more details please refer to 2 3 Input specification and measuring range For jumper pin setting of universal input card KRN UI2 by inpust specification refer to 4 2 I O card Set range Refer to 2 3 Input specification and measuring range Factory default TC K 8 1 8 Range Scale Point Dec
112. nics Co Ltd 105 I 8 Parameter detail setup Autonics 8 5 10 Alarm Speed Alarm record speed fe Fm 23456789 Aah med 22 36 17 a RECORD SETUP NAME gt VALUE gt Divide fone 1 standard Period Option Period Listing Language English Alarm Speed 2 Arnim h BAM Far Lie D Set record speed for alarm cause and details when alarm occurs It is actiaved when Record Mode Record mode is set as Graph You cannot set Alarm Speed Alarm record speed as below Standard Speed Standard record speed If you change Standard Speed Alarm Speed is changed as the same set value automatically When alarm occurs record progresses with set Alarm Speed When alarm is reset it returns to Standard Speed Set range 10 20 40 60 120 240mm h Note Factory default 20mm h If alarm and digital input occur at the same time digital input is ignored and it records with the set value of Alarm Speed Alarm record speed When alarm is reset it returns to Standard Speed Standard record speed In graph mode record speed is change by Standard speed Alarm and Option Speed Backup data is printable only with Standard speed Therefore original graph mode printout and backup graph mode printout may be different 8 5 11 Power On Status Record status when power ON OR AE us 8 RECORD SETUP Fy MAME gt VALUE standard Period ae Option Period Listing Language English Alarm Speed 2 Arm h Power On Status Cl pr
113. o set Enable Disable regardless of RS485 or Ethernet setting Copyright Reserved Autonics Co Ltd 87 8 Parameter detail setup Autonics Interface Compliance with EIA Compliance with USB Application standard RS485 V2 0 1 units 31 units l l Max connection number of occupations 1 units address 1 to 127 per a unit Single cable within Communication Max 1Km 100m Single cable within distance 1 Below 9600bps Recommended over 1 5m CAT5E Communication Half Duplex Full Duplex method Communication synchronization Asynchronous Asynchronous Asynchronous method Communication 2400 4800 9600 19200 10 100Mbps 12Mbps Full Speed speed 38400bps Communication nn 51099 ms response wait time Stop Bit 1 2 bit Modbus RTU Modbus TCP Modbus RTU x 1 When connecting through the network such as network hub HUB and gateway etc there is no distance limit but it is recommaned to use min network Please use communication cables which is satisfied the below conditions Shield Twist Pair over AWG24 characteristic impedance RS485 communication 100Q capacity component 50pF m cable length max 1km Ethernet communication Over CAT5E cable max length 100m USB Device communication Single cable built in ferrite core within 1 5m E Note USB Device communication may cause recognition error by external noise and environment during connecting PC If there is error please re connect this
114. on alarm output is OFF If it is an alarm condition alarm output is ON and maintains ON status Alarm output HOLD Latch 1 Alarm latch Standby First alarm condition is ignored and from second alarm condition sequence standard alarm operates If it is an alarm condition it operates both alarm latch and standby Alarm latch S 7 o sequence When power is supplied and it is an alarm condition this first and standby S h alarm condition is ignored and from the second alarm condition alarm sequence latch operates X 1 In case Alarml Type Alarm operation mode is SBA Input break alarm or P END No recording paper alarm you can only select Latch Alarm latch X 2 Condition of re applied standby sequence Power ON changing the set alarm temperature forced alarm reset Set range None Latch SitBy La st Factory default None G Note In case for input break alarm SBA no recording paper alarm P END standby sequence or alarm latch and standby sequence option does not operates and you cannot set it In case of alarm by alarm latch to reset alarm output press key for 3 sec at not alarm condition use alarm reset function by digital input or turn OFF the power and ON To reset alarm output by digital input DI L Type Select digital input 1 from DIGITAL INPUT SETUP is should be set as Alarm Reset Reset alarm output is available only when alarm option is set as alarm latch or alarm latch and sta
115. or dd day mm month yy year Set range yyyy mm dd dd mm yy mm dd yy Factory default yyyy mm dd B 112 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 6 4 Summer Time Summer time OT AE ud SYSTEM SETUP MAME gt VALUE Device Mame KANTEA Recorder ime Date T 2911 96 15 Wedd 22 41 17 Date Tyre Time dd Summer Time summer Time Period AknBAd AAR Heed AAR mg Fete Eu EE i Le This function is for applying summer time daylight saving time in specific contries and regions When you set Summer Time it adds current time and 1 hour and displays S mark in front of the date and time on LCD screen or in front of the date on recording paper Set range Disable Enable Factory default Disable 8 6 5 Summer Time Period Summer time period we ee oh es45e7 age ur ere PS 123456 7890 ur STSTEM SETUP En od SETUP ai MAME gt VALUE gt METTE Device Name KRNIAA Recorder rder Date Time 2411 46 15 led 22 41 24 Start DateTime BE 31 aye Date Type sy mn dd End Date Time 9 1 A mdd summer Time Enable able Summer Time Period Heme eh Aknkkd Bah Etat Fat mfa EE mifa LG ote 1 D Li Designate summer time daylight saving time period When Summer Time is set as Enable it is activated Designate Start date Time and End Date Time Set range 01m01d 00h to 12m31d 23h Factory default Note When changing summer time it crea
116. orded 8 6 12 Backlight LCD backlight brightness mt ae Ren Fos A eee SYSTEM SETUP E NAME gt VALUE Reservation Time HARAS 27 hAfAkS Alarm Sound sampling Rate Log Speed Backlisht Lak rs Designate LCD backlight brightness as 4 levels Setrange OFF Min Standard Max Factory default Standard 8 6 13 Backlight On Off LCD backlight ON method fe Pm 234567 BSW MANSY med 22 48 07 a sta EM SETUP NAME gt Alarm Sound OFF sampling Rate 125m Log Speed 5 Back ight standard Backlight On Off Designate LCD backlight ON method If you set as Always it maintins ON status as Temp it maintains only for 30 sec when key is input Set range Always Temp Factory default Temp Copyright Reserved Autonics Co Ltd 117 8 Parameter detail setup Autonics 8 7 FILE MEMORY SETUP File Memory setting You can set the parameter about parameter set file and storage data Move to FILEMEMORY SETUP with BBZ keys press key to enter FILE MEMORY SETUP 234587890 Ah M t o ml Ta dl23456 7890 et M l HO a DIGITAL INPUT SETUP 20 FILEMEMORY SETUP COMMUNICATION SETUP T C NAME gt VALUE RECORD SETUP BUENSC Load set File sta TEM SETUP save set File select FILEAMEMORY SETUP BURN C Memory Status q3 USER INFORMATION SETUP Memory Clear Clear RECORD BACKUP SETUP USB LogData Save Disable Fart an ets on m Parameter list None Default pm
117. osed of each alarm output channel from the set alarm output card in Select Alarm Card Select alarm output card You can use alarm output as relay output or transistor output by inserting the desired alarm output card Relay output KRN AR4 transistor output KRN AT6 Set Alarm Alarm output ae Description occur Transistor Normally In normal status it is open OFF eontacrOpen OFF Open If alarm occurs it is closed ON Contact Close Transistor ON Bi Contact Close Transistor ON Normally In normal status it is closed Closed If alarm occurs it is open Contact Open OFF This function displays as Alarm _ Status and it is connected relay or transistor Type s output card information One card for relay has 4 outputs Alarm 1 Status to Alarm 4 Status for transistor has 6 outputs Alarm 1 Status to Alarm 6 Status Relay output card KRN AR4 is connectable up to 3 and transistor output card KRN AT6 is connectable up to 2 at Slot7 to 10 Alarm output turns ON or OFF by total 4 alarm conditions and relay transistor output are able to output by max 48 alarm conditions However every relay output and transistor output condition is OR operation Among several alarm conditions connected one alarm output even one alarm condition is met output must turn ON Set range N O N C Factory default N O G Note Relay and transistor type output is basically fixed as Normally Opened method and H W when power is
118. ot output alarm There are two alarm output types Transistor and Relay output KRN recognizes automatically the connected type and displays it In this parameter transistor output type is displayed as TR SL_JAL L J and Relay output type is displayed as RELAY S JAL D These parameter s meaning is as below SLI The number of module connected SLOT AL L Alarm output channel number Number in parenthesis LJ the number of designated alarm as output in the specified channel Set range None O SOAO Q 0O Factory default None 8 2 10 Select Alarm Card Select alarm output card en OY o Ol 23456789 NLA TUE 171617 a ALARH SETUP CH1 51UI 1 NAME gt select Alarm Card Sok select Alarm Card Hlarm Status Hlarm 1 Status Alarm z Status Alarm z Status Alarm 3 Status Alarm 3 Status LL 4 Li E LLI 4 Select alarm output card KRN AR4 KRN AT6 to set output type Normally Open Normally Closed of alarm output In front of output card name relay or transistor abbreviation is displayed for easy to know connected module type when selecting output card Copyright Reserved Autonics Co Ltd 81 8 Parameter detail setup Autonics 8 2 11 Alarm L_ Status Relay and transistor output method fet Pio S1234567890NAAEN web 22 28 33 ALARM SETLP CH3 SEUT 1 E MAME gt Hlarmd Alarm No select Hlarm Card Hlarmi 1 Status Alarm Status n Set alarm output method Normally Open Normally Cl
119. ot connected universal input card KRN UI2 and displays as channel as soon as power is ON Channel name form is as below Channel Slot card CH S Ul number number input CHO06 S3UI 2 It means 6th channel and 2nd input of 3rd slot connected universal input card Input Set Copy Copy input parameter MAME VALUE select Ul Card select UI Card Input Set Copy CH Select Alarm Set Copy LCD Parer Record Hlarmi Tyee Pen Color Alarmi Ret CH Record fone Alarmi Option fm Pl rh 5 You do not need to repeat the setting of same parameter for each channel KRN100 copies set values of the set completed channel to other channels Copyable parameters are as following Range Scale point Decimal point Low Scale Lower limit scale High Scale Upper scale Special Function Special function Two Unit Display the degree of a vacuum static Reference Chanel Reference channel pressure Input Bias Error correction Span Gradient adjustment Record Method Data storage method Filter Type Input digital filter Filter Counter The number of digital filter Burnout Action Display setting for break High Range amp Graph Scale Upper limit input value and Low Range amp Graph Scale Lower limit input value and graph scale value graph scale value Set range None CHO SHQUI Factory default CH Select Copyright Reserved Autonics Co Ltd 55 I 8 Parameter detail setup Autonics 8 1 3 LCD Paper Record Di
120. out in graph mode may be different 130 Copyright Reserved Autonics Co Ltd Autonics 8 9 1 8 9 2 8 Parameter detail setup Record Backup Backup data record mle Pio 923456789011 E RECORD BACKUP SETUP NAME gt Record Backup Stop Backup Data List File Hot Found start Date and Time ABBE HAAA AR AR AA End Date and Time ARREARS AR AA AA Backup Print Mode Graph Designate whether recording saved backup data item Description O o O Not printing the designated backup data on Backup Data List it returns to RUN op mode Records the designated backup data on Backup Data List from start date and time to end date and time and returns to RUN mode At RUN mode the icon for record changes as and flashes KRN100 reads backup data to the end and starts recording Depending on backup data file size reading time may take longer When starting printing by Record Backup function starts recording as below figure DATE 11 09 17 11 42 26 11 09 17 13 12 34 Backup data start and end point FILE NAME KRN100 20110917 114226 K RD t gt Backup data file name E tte ttt RECORD BACKUP START Backup data start line Set range Start Stop Factory default Stop Backup Data List Backup data list fe Pm 234567890 NAM ned 23 54 13 a RECORD BACKUP SETUP NAME gt Record Backup sto Backup Data List File
121. pe None 8 2 4 Alarm Ref Channel AlarmL reference channel m M ON 23456 7690 eS os EN fae M ON 23458 789 eS ee re ALARM SETUP CH1 51UI 1 SM ALARM SETUP CHI SIUI 1 ho Select BE NAME gt VALUE gt NAME gt YALU CHI S1UI 1 select UI Card CHI STUT 1 select UT Card CH CHE STUT E Alarm Set Copy CH Select Alarm Set Copy CHS S2UT 1 Hlarmi Tyee OV Lo Hlarmi Tyee CH4 SeUT 2 Alarm Ref CH Alarm Ref CH CHS S3UI 1 Alarm Option Hone Alarm Option CHE S3UI 2 i Gi Fr D n T oy Designate reference channel which is standard of deviation upper limit alarm DV Hi or deviation lower limit alarm DV Lo If display value of relevant channel is lower than the display value of set reference channel deviation upper limit alarm or deviation lower limit alarm turns ON This parameter is activated when Alarm Type Alarm operation mode is set as deviation upper limit alarm DV Hi or deviation lower limit alarm DV Lo Set range None CHO SCUI G Factory default 76 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 2 5 Alarm Option AlarmL option aa M 801 23456789 1014 Ea n 11536588 ALARM SETUP CHI S1UI 1 le NAME gt VALUE select UI Card CHI STUI 1 Alarm Set Copy CH Select Alarm Tyee OY Lo Alarmi Ret CH Hone Alarm Option n FEF Set alarm output by alarm operation Standard If it is an alarm condition alarm output is ON If it is a clear alarm alarm conditi
122. per should be replaced Present recording paper lefts only 330mm from terminal mark Recording paper s terminal mark red star shape is displayed When power ON after booting screen KRN100 does not change normal operation screen SD card of inner KRN100 has problem Please contact our service center USB memory s file system supports only FAT16 and FAT32 Format as FAT16 or USB memory is not recognized FAT 32 If partitions of an USB memory are divided KRN100 recognizes only first partition Check communication line connection and Cannot connect communication by Ethernet reset it as following 8 4 COMMUNICATION SETUP Communication setting Check communication line s A B signal Cannot connect communication by RS485 polarity is connected correctly Reset it as communication following 8 4 COMMUNICATION SETUP Communication setting Copyright Reserved Autonics Co Ltd 149 11 Troubleshooting Autonics 11 1 Error message Displays error messages on screen and print data when error occurs Error message Description In case Input Type is temperature sensor thermocouple RTD if input value is higher than upper limit range this error message flashes If input value is within upper limit range it is removed automatically In case Input Type is analog current voltage if input value is higher than over 10 of upper limit input range this error message flashes If input value is w
123. ph left and digital number right 4 channels are displayed per one screen To switch channel please refer to 7 1 2 Channel switch Bar graph ME o 223456690185 TUE 14 53 08 Displays input measuring value of each channel as bar graph left and digital number right You can easily check present measuring value within the set display range as level 4 channels are displayed per one screen To switch channel please refer to 7 1 2 Channel switch Copyright Reserved Autonics Co Ltd Autonics 7 Operation 3 Digital number Displays input measuring value of each channel as digital number Digital number display is divided as 1 channel digital number 8 channels digital number 12 channels digital number e Display of 1 channel digital number Displays 1 channel per 1 screen with big font size It has high visibility ret Pan OM 234567 89101110 Af TUE 14 11 54 CH CH 2 TC K 241 8 C e Display of 8 channels digital number Displays 8 channels per 1 screen 2011 62 61 TUE 14 11 54 BURN c 36 0 BURN c 28 8 C e Display of 12 channels digital number Displays 12 channels all channels per 1 screen E 2616 69 45 263 153 2 C LE G EC G Copyright Reserved Autonics Co Ltd 45 7 Operation Autonics 7 1 2 Channel switch It displays measuring value of all input channels by switching channel of display types You can set channel switch mode as a
124. ping recording changing input characters on virtual keyboard status and displaying Function key Press this key for 3 sec in stop state ink cartridge moves to the center Use this to replace ink cartridge Using this key for going out from parameter setting group or setting manual channel switch mode It also executes to release auto channel switch mode and printer list output 3 sec function Using this key for moving parameter in setting mode increasing digit value setting auto channel switch mode and manual feed function by pressing over 3 sec in stop state Using this key for moving parameter in setting mode setting manual channel switch mode and forced alarm reset 3 sec EED OFT Using this key for moving parameter in setting mode decreasing digit value changing display mode and executing manual digital memo 3 sec in recording state Using this key for entering setting mode 3 sec and set value change ENTER oe mode USB Host Connects an USB memory It recognizes max 32Gbyte and if using cable it is available up to 1 5m Copyright Reserved Autonics Co Ltd 17 i 1 Overview Autonics E Note Function key Use this key to enter virtual keyboard in parameter setting Press gt stop key and Function key appears on lower screen as below figure Press Ka AN ME F _ gt 4 ES KE or key as below Function key it operates the appropriate Function key s operation INTELLIGENT HY
125. pyright Reserved Autonics Co Ltd 133 i 8 Parameter detail setup Autonics 4th In menu screen select Select File and press key and S is displayed in front of backup data Select currently saving file it displays only Press key to operate Function key and press key to enter and it selected File Information Checkes Backup Data information Prev Page Next Page Moves page If there are lots of files Up Directory Moves parent folder Into Directory Enter the folder dth You can check save time information of the selected Backup Data RECORD BACKUP SETUP NAME gt Record Backup Backup Data List start Date and Time 2414 1229 19 42 47 End Date and Time 0141229 18 A3 37 Backup Print Mode Moves parent folder Ist Press key in selected file to activate selected screen Select Up Directory and it moves to parent folder Poy 2345678910 A rut 18 55 38 SRE Delete File Internal 5 1 11 File Infomation KRN AR 2A1A1229 188 lt lt Prey Page AMI est Page gt gt RENT AA 24141229 1 Up Directory KERNI GH AA 181279 174 Into Directory KRMN AR 26141279 179eSelect File ecord Backup Memory Ope Internal 3 1 12 USE Memory d 1 12 CIE USB Mot Found TRET MATET 3rd To move desired date folder press key at the selected folder and menu screen is activated Select Into Directory in this menu it moves to inner folder Hove to USB Memory Delete File cfa File Infomation ARE lt l
126. rogressing initial setting Autonics Sensors amp Controllers KRN100 Alarm Out Init Screen for checking error of inner system memory Autonics Sensors amp Controllers Memory Cheking 000 If there are lots of log data files booting time may take a long time Delete log data file For more information refer to 8 7 4 Memory Clear Delete memory Screen for error of inner system memory SO Card Checking 777 Above this figure if there is error of inner system memory KRN 100 cannot operate normally Please contact us Autonics service center 82 32 820 2343 Copyright Reserved Autonics Co Ltd 37 i 6 Display Autonics 6 2 Screen layout Screen layout is divided as two upper screen for status display lower screen for measuring value display virtual keyboard display parameter display INTELLIGENT HYBRID RECORDER Status display Measuring value display Virtual keyboard display Parameter setting display amp i gt i A EKTE KRN100 LIST M ALRESET FEED DISPLAY 6 2 1 Status display Upper screen displays recorder status and information of recorder as icon ala 3 l 4 dsle 8 Name Desorption Marks if for starting recording measuring value of Record start icon recordable channels Record stop icon Stops recording measuring value Flashes during list recording Flashes during reservation recording FEED icon Flashes during fe
127. s User1 pms User2 pms User3 pms User4 pms User5 pms Load Set File Open parameter setting file User1 pms USB User2 pms USB User3 pms USB User4 pms USB User5 pms USB None Default pms User1 pms User2 pms User3 pms User4 pms User5 pms Save Set File Save parameter setting file User1 pms USB User2 pms USB User3 pms USB User4 pms USB User5 pms USB Memory Status Memory capacity 0 to 100 display range 0 Memory Clear Delete memory Cancel Aller Clear Disable Stop USB Memory Copy Move Move Copy data USB Copy Move 118 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 7 1 Load Set File Open parameter setting file w bm 623456890186 l es sas fele Um bl 23456 7890NAAEP her erasia FILEHEMORY SETUP ES FILEHEMORY SETUP shane FA NAME gt WALUE gt MANE gt One Load Set File Load Set File Default pms Save Set File Select Save Set File ged Memory Status d Memory Status Jed Memory Clear Clear Memory Clear ae USB LogData Save Disable USB LogData Save Dose Le Matte a Dot io mim Matte Dot io User pms Applies set value of saved parameter set file When applying this set backup data user unit and booting logo are not changed None Default pms file is activated and if there is User1 pms to User5 pms User1 pms USB to User5 pms USB file parameter set save file it is activated Set range None Defaultpms User1
128. so construct project list for convenient project file management Monitoring data log It logs the data during monitoring and is able to save it as one of DAQMaster data file ddf or CSV file csv You can load the saved CSV file in Microsoft Excel directly You can also designate file name storage rules and storage folders for easy file management Data analysis You can analyze data file ddf with DAQMaster s data analysis function as spread or graph You can save the analysis as rtf txt html or csv file on spread Modbus map table reporting output It can output the registered Modbus device address map as report You can save the report for Modbus map table as HTML file html or PDF file pdf Supports multi language It supports Korean English Japanese and Simplified Chinese To add a different language modify the files in the Lang folder rename and save it Supports script You can designate each other different I O process by device using Lua script language 136 Copyright Reserved Autonics Co Ltd Autonics 9 DAQMaster 9 3 Dedicated KRN100 functions Among DAQMaster s functions there are dedicated KRN 100 functions during communicating with DAQMaster Property I x KRNIOO gt gt 1 General Device Name KRMIOO Unit Address 1 Model Repeat Interval 1000 msec Frame Time 40 msec Unit Mame version ES Print Control amp Status Mounting Slot INPUT SETUP
129. splay and record measuring value INPUT SETUP NAME gt VALUE select UT Card CH3 s2U1 1 Input Set Copy CH Select LOO Parer Record Pen Color 3 Black Record Zone Hone Set whether to record measuring value If you set ON KRN100 displays and records measuring value on LCD screen and recording paper If you set OFF KRN100 does not display and record measuring value on LCD screen and recording paper Setrange ON OFF Factory default ON 8 1 4 Pen Color Record color DKHA E a INPUT SETUP CH 51UI NAME gt VALUE gt select UI Card CHI STUT 1 Input Set Copy CH Select LOO Parer Record Pen Color Record one Designate record color when recordingmeasuring value Setrange 1 Violet 2 Red 3 Black 4 Green 5 Blue 6 Brown Factory default Automatically set 8 1 5 Record Zone Record zone fun S45 TAMIA INPUT SETUP CHS S2UT HAE gt VALU Select UI Card CHS S2UI 1 Input Set Copy CH Select LOO Parer Record ON Pen Color 3 Black Record Zone In case record mode is graph mode you can select record zone for to graph measuring value when recording Set range is set accoridng to the set value of 8 5 6 Divide Zone Record zone division from RECORD SETUP If the set is None record zone is full width 100mm of recording paper Set range None 1 Zonen n set value of Divide Zone Record zone division Factory default None 56 Copyright Reserved Auto
130. t 4 00 20 00mA 4 20mA Resolution 10uA x 1 C TT Same temperature sensor type as existing W5 TT X 2 G TT Same temperature sensor type as existing W TT x 3 Russian type L type temperature sensor is divided from general purpose L type Note When changing input type to voltage over 2V or current set the jumper pin of KRN UI2 universal input card lts factory default is tempeature sensor input Copyright Reserved Autonics Co Ltd 25 I 2 Specification Autonics 26 O Copyright Reserved Autonics Co Ltd Autonics 3 Dimensions 3 Dimensions 1 KRN100 gt E E E E B TT E B X Back side dimension is with installed I O cards to every slot 2 Panel cut out Min 175 1385 Vv X Use panel which is 2 to 8mm thickness Min 175 O Copyright Reserved Autonics Co Ltd 27 i 4 Connection Autonics 4 Connection 4 1 KRN100 This figure is back side of KRN100 04000 00 0S model JUUOOOOUUUOO BOYAPT gd I sauce 50 60Hz 55VA Slot Description Connects universal input card KRN UI2 Connect digital input card KRN DI6 alarm output card KRN AR4 KRN AT6 and transmitter power output card KRN 24V3 Connects communication output card KRN COM 28 Copyright Reserved Autonics Co Ltd Autonics 4 Connection 4 2 I O card Universal input
131. t Prey Page d Next Page gt gt Ue Directory Record Backup Memory Ope Internal 6 1 15 USB Memory A 1 12 KANT HA 26101220113709 USB Not Found KANT BARA 228 992 746 KAM AA 28141220 A92611 KAM AA 28141220 892139 KAM AA 24141220 A91622 TE AR LL FRF sere fe 134 Copyright Reserved Autonics Co Ltd Autonics 9 DAQMaster 9 DAQMaster 9 1 Overview DAQMaster is integrated device management program and is able to utilize for temperature controller product line meter product line counter product line and recorder product line etc DAQMaster provides graph user interface GUI for easy and convenient integrated several products parameter setting and data monitoring ronal gJ DAQMaster File View Run Tool Windows Help BESO 0 0 wm Poe e x ao setvaue o ve cron Type G E N Description it i Create Date Runtime UI a a ee ee ee gt Modify Date 20 Creation Fa FT Grid Grid 1 10 2010 3 35 39 PM i STE s a Revision Fin Panel 3_Present Value Version vendor ONICS ME Line Graph Line Graph Product Name TK4 Ne PRE NEVE ARES en I JE Ne E RS Major Revision H 5 40 15 SI 5 35 00 15 35 5 35 20 15 35 30 15 35 4 ob Bar Graph Bar Graph Time hh mm ss on oo Fin Panel 3_5et Value Device r 1 Runtime Screen Library sno 1 35172380 pauoddns Address Status COM1 Connected ModBus Master Connected d T TK4 AUTONICS 1 EA 3 TK 4M B4RR Con
132. t voltage W mass fr SN EE SC EE we oe we bla f a mo wee fe ume pif ow fa fe fa nm o fue fou fa fae fe p fe ff fer You can use user defined unit image by selecting user defined User0 to User9 unit Please refer to 9 3 2 User unit setting LP Note The unit with multiplier such as kg cm or complicated unit may be printed in low quality due to low print resolution 58 Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 1 10 High Low Range amp Graph Scale Upper Lower limit input value and graph scale value Set the actual used input range Lower limit input value Upper limit input value in analog input If input range becomes small the resoultion also becomes low in proportion to total range Decimal point position is changed by Scale Point Scale decimal point position setting 1 Low Range Lower limit input value mA Po 234567 OMA eataa ee kio Sp 23456 7890 ro io ie INPUT SETUP CH1 5 UT 1 La lt NAME gt VALUE mj ate ciole Fial BEI Input Type Dane biselay Temp Unit me o r afrfsjrfuf frfefal Low Range 58 bn gli lilv zfsee sfo High Range GA AA 5 Fr Set the actual used lower limit input value within input range of Input Type Input specification e Set range Min input range value to upper limit input value High Range F S 5 In case input range is 0 to 100 C set range is 0 to 95 C e Factory default 2
133. tatus List printing at start recording is set as ON O PRINT MODE DIGITAL 2011 06 14 THU 11 35 27 O SPEED STANDARD 240 ALARM 240 OPTION 240mm H O CH INPUT LO RNG LO SC UNIT TAG HILRNG HI SC FILT Records TC K 200 0 CH 1 1350 0 Standard standard DPT100 200 0 parameters only Input specification INPUT channel name TAG lower limit input value LO RNG upper limit input value HI RNG display unit UNIT input digital filter FILT PRINT MODE DIGITAL 2011 06 14 THU 11 35 27 O SPEED STANDARD 240 ALARM 240 OPTION 240mm H O CH INPUT LO_RNG LO_SC UNIT O TAG HILRNG HI_SC FILT ALM1 VALUE RELAY ALK2 VALUE O ALM3 VALUE RELAY ALK4 VALUE O 1 TC K 200 0 Records O CH 1 1350 0 0 DV Lo None None standard O None None None 2 TC K 200 0 parameters and a CH 3 1350 0 0 O DV Lo 1000 0 None None None O None None None None parameters O NETWORK 485 DISABLE USB DE ENABLE E_NET DISABLE option Input specification INPUT channel name TAG lower limit input value LO RNG upper limit input value HI RNG display unit UNIT input digital filter FILT alarm mode ALM alarm set value VALUE alarm number RELAY communication interface NETWORK USB E NET Set range Standard Option Factory default Standard Note List is printed with max record speed 240mm h Depending on the number of channel it may take long time Therefore be sure this when prin
134. td 13 1 Overview Autonics 1 2 Component and sold separately 1 2 1 Component MIT PPT HAAD NSG CEE Recording Ink cartridge lea paper lea pr gr at PA i Loy mm KRN100 Fixing bracket 2ea User manual VG Note Before using KRN 100 check the component If any component is left out or damaged contact our company or seller Autonics service center 82 32 820 2343 1 2 2 Accessory 1 I O card Universal input card Alarm output card KRN UI2 KRN DI6 KRN AT6 Alarm output card Transmitter power Communication output KRN AR4 output card KRN 24V3 card KRN COM 2 Communication converter SCM 381 RS232C RS485 converter SCM US48I USB RS485 converter Appearances of SCM 38I RS232C to RS485 converter and SCM US48I USB to RS485 converter are same 14 Copyright Reserved Autonics Co Ltd Autonics 1 Overview 1 3 Ordering information 1 Ordering information 0000 060 oo 02 2eme RUBAN o CK xae8 CETTE 10 10 channel KRN UI2 X 5EA fo None fo Nome fo fn o fn C SE FePowervotage 0 roozaovac soon Copyright Reserved Autonics Co Ltd 15 1 Overview Autonics 16 2 I O card model name Max Function and number of Type Model name connectable channel card Universal input d KRN UI2 Universal input 2 channel 6EA 1 to 6 car Digital input card KRN DI6 Digital input 6 channel Alarm relay output 4 KRN AR4 3EA channel Alarm output
135. ter output part and power terminal of the product should be short as possible It may cause damage to the product malfunction by surge etc Before connecting temperature sensor thermocouple RTD and analog voltage current input set jumper pin of universal input card as input type It may cause damage and malfunction to this unit Do not connect or separate input output card when the product power is ON It may cause serious damage Do not open the cover or insert your finger during operation It may cause electric shock Do not control with alarm output or measure data during firmware upgrade Alarm output contact input data measurement etc do not operate normally Therefore this unit does not operate as intended Check the complete message for firmware upgrade and turn OFF to ON the power If do not turn OFF to ON the power it does not operate normally All parameter set value is initialized after firmware upgrade It may not operate as same way with before upgrade operation Use voltage output of transmitter power output card only for transmitter power It may cause damage to output module The specifications and dimensions of this manual are subject to change without any notice Copyright Reserved Autonics Co Ltd vii i Safety Precautions Autonics viii Copyright Reserved Autonics Co Ltd Autonics Table of Contents i Table of Contents FC Ce EEE EEE lil SEG EE LR NG PEER EE IV
136. ter setting information output 3 ES Manual feed When stop recording 35 INPUT SETUP oO ooo o o er KE ALARM SETUP T DIGITAL INPUT SETUP HCOMMUNICATION SETUP RECORD SETUP SYSTEM SETUP wpa HFILE MEMORY SETUP DISPLAY ET gt USER INFORMATION SETUP RECORD BACKUP SETUP lt 4 Function key L SENS XOK a EN Cancel CR Copyright Reserved Autonics Co Ltd 43 Autonics 7 Operation 7 1 7 1 1 Screen display Measuring value display KRN100 displays measuring value as trend graph bar graph and digital number display 1 channel 8 channels 12 channels You can select one by 44 ME key Trend graph OA OLA PE ye CHI 214 2 C ite pe 130 jt CH 3 58 IT ar NT DISPLAY DISPLAY Digital number 12 channels Bar graph RTE NE mY co 23456789 0 IRA ease Jru 14 51 55 184 6 6 CH NONE 1 CHI BURN x o CH 1 515 2 C CHE NONE 12 CH 35 4 CHO NONE gn CH 2 24 9 C BURN C CHIA NONE 3 CH3 29 8 c 94 5 C CHI NONE vi 4 CHa 34 5 C CHI NONE m CH 4 50 0 Digital number 8 channels Digital number 1 channel om AY 12345578 90 1l amp fs an 1 EE ele Kb 81234556 789018 les 12183787 om BURN fir BURN c CH1 CH 1 TC K hug 74 5 C EP 36 0 o Eh 29 3 c A BURN C qe ch 50 0 fits 28 8 C BURN C Displays input measuring value of each channel as trend gra
137. tes new backup data Copyright Reserved Autonics Co Ltd 113 I 8 Parameter detail setup Autonics 8 6 6 Reservation Type Reservation record OA OL AE ude SYSTEM SETUP NAME gt summer Time Period Reservation Type Reservation Period Reservation Time Alarm sound This function is to set reservation time At the set time it starts stops recording automatically You can select reservation record either Repeat Repeat ON OFF or Single Single ON OFF When selecting reservation record Reservation Period Reservation record period and Reservation Time Reservation record time are activated When reservation record is set icon flashes with recording or m stop recording icon icon tuns OFF when reservation setting is Disable Set range Disable Repeat Single Factory default Disable 1 Repeat Repeat ON OFF From start recording date to end recording date it records data at from the set start time to the set end time End time must be later than Start time Reservation Period Reservation record period setting Start Date 2011 1 1 End Date 2011 1 3 Reservation Time Reservation record time setting Start Time 12 00 00 End Time 23 59 59 12h00m00s 23h59m59s 12h00m00s 23h59m59s 12h00m00s 23h59m59s y Y y y y Time 2011y01m01d 2011y01m02d 2011y01m03d It records data every at from 12 00 00 to 23 59 59 in from 1 Jan 2011 to 3 Jan 2011
138. ting the list 108 O Copyright Reserved Autonics Co Ltd Autonics 8 Parameter detail setup 8 5 14 Zone Dot Line Distance Dot line for zone division ur PS hese 789 01 Aer aan ue EE RECORD SETUP ad NAME gt Power On Status Aun status List Out Option fone Dot Line Distance Ann CH Print Distance ed Ann 1 mim E 1 a Li Designate present absence and interval of dot line at right to divide zone when zone is set Dot line for zone division is printed in violet Set range None to 8 0mm Set with 0 8mm interval Factory default 4 0mm G Set the interval between i dots 8 5 15 CH Print Distance Record interval for each channel graph ml Po Sp 23456789 one Aah lue SE RECORD SETUP FY NAME gt Power On Status Aun status List Out Option Dot Line Distance CH Print Distance MENE too Bin il Designate the interval for printing channel number of each graph as below figure It is activated when Record Mode Record mode is set as Graph Set range No Print to 100 0mm Set by 10mm interval Factory default 20 0mm HOMO eg 0000000 Copyright Reserved Autonics Co Ltd 109 I 8 Parameter detail setup Autonics 8 5 16 Start Line Print Start line when starting record ur fe Mon 123456 BSA med 22 25 21 a RECORD SETUP MAME gt Run Status List Out Option Dot Line Distance Aram CH Print Distance TAR rar Start Line Print MT O RECORD STAR
139. u want the wizard to do Install the software automatically Recommended 8 Install from a list or specific location Advanced Click Next to continue 34 Copyright Reserved Autonics Co Ltd Autonics 5 Installation 4th Select Search for the best driver in these locations and check Include this locationin the search Click Browse and select the folder which has KRN100 USB Serial Drivers and click OK Found New Hardware Wizard Browse For Folder Please choose your search and installation options Select the Folder that contains drivers for your hardware E Desktop au reat 4 B My Documents Use the check boxes below to limit or expand the default search which includes local p My Computer a My Network Places Search removable media floppy CD ROM Li Drive Include this location in the search KRN100_USB Serial Drivers Search for the best driver in these locations paths and removable media The best driver found will be installed JEW TOILE C Documents and Settings utonics Desktop KRN v Don t search will choose the driver to install Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware To view any subfolders click a plus sign above Sth If hardware compatibility message appears click Continue Anyway and it processes the next
140. up data record 131 8 9 2 Backup Data List Backup data list orrrrrnnrnnnnnnrrrnnrrrrnnrrnrnnrernnnrrvnnnennnn 131 8 9 3 Start Date and Time Start time for data storage 132 8 9 4 End Date and Time End time for data storage 132 8 9 5 Backup Print Mode Backup data record mode 132 8 9 6 Select Print Mode Backup data recording mode setting 133 9 ECU AS TET nana dead naan one AA 135 9 1 OVErvieW ccccccccceecccceneecceeeeceaececeueessaacessaucesseaeeeseueesseaeeeseaeeesssesseeessuaeessageenss 135 9 2 EE gt tit Mii ASAE 136 9 3 Dedicated KRN100 functions rannrnnnnnrornnnnvnnnnrvnnnnnvnnnnvnnannnnnannnnnannrnnannennnnee 137 93 1 RECON BECK une eee ankre ete 137 932 NTN 138 9 3 3 Boot logo image setting 139 9 3 4 Backup data Checking function 140 TO ELLE 1 LE LOS PS NS 143 10 1 Ink cartridge replacement ss 143 102 Recording paper F DIACEMENE asesinan 144 11 Troubleshooting axranrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnenn 149 11 1 16 UNS SS EEE 150 XII Copyright Reserved Autonics Co Ltd Autonics 1 Overview 1 Overview 1 1 Feature of KRN 100 KRN100 is 100mm hybrid recorder with dot It combines functions of paper recorder and paperless recorder by saving function with an USB memory the world s first and by adopting Trend graph Bar graph digital number display function through graphic LCD KRN100 enables to print the sav
141. uto channel switch or manual channel switch 7 1 2 1 Auto channel switch A screen displays 4 channels and automatically switches other screens by 3 sec period 1 Trend graph 1 to 4 channel Ce PRAT g esaseragone MESEN 1 43 ry CH B U R H g 24 6 C 3 sec 3 sec 9 to 12 channel 5 to 8 channel OM END AS PE m F 23456 789 0 0 eS ees ni H AGA g 47 48 LE CHE C ten 36 0 CHI g CH 11 C ilio 79 0 c 2 Bar graph OMERE H CH A 24 6 C 31 9 C O a amp 3 sec 3 sec 9 to 12 channel 5 to 8 channel m RATE co 5 TUE 14 58 28 a eH 23 456789 100 el Aale ti i BURN HW T BURN 30 0 a BURN C C tie BURN C 9 1 C 46 Copyright Reserved Autonics Co Ltd Autonics 7 Operation 3 Digital number 1 channel 1 channel mA Pe 81234568 ag RT darts CH1 CH 1 112 5 C 3 sec 3 sec 12 channel 2 channel me 175 23456789 0 E fa Po 234567890112 DAS rois CH12 CH 12 10 CH2 GH 2 TC L_ 31 3 C 4 Digital number 8 channels 1 8 channel 9 12 channel m Bhs 067A MLA ee JIS DIT 23456700 orm VIS ct 49 5 LE BURN c cH BURN amp mz 22 7 c EB 36 03 aq 35 pie BURN ME 27 8 c dr BURN c CHIT 42 9 amp ar 50 0 27 2 C HER 43 4 5 Digital number 12 channels 1 12 channel a oh oi 23456789 0M non 14 92 87 CHI FAA CHT BURN E 23 8 C 27 8 C 2o T OG BURN D
142. utonics 8 Parameter detail setup 8 7 5 USB LogData Save USB storage function fe Fm 23456789 LAN we 17 10 11 a FILEMEMORY SETUP NAME gt Load Set File save Set File Memory Status Memory Clear USE Loglata Save alert otic Set whether to save backup data which is saved on system on an USB memory When selecting Enable to saving data to an USB memory it also saves data to system memory at the same time A connected USB memory at left side USB Slot KRN100 starts to save It takes check time for storage free space approx 10 to 60 sec depending on memory capacity The data is saved as KRN100_20100815 year month day 091050 hour min sec KRD file name and if main set is changed or backup data capacity is over 100MByte it creates new file Set range Disable Enable Factory default Disable X Main set is as follwoings Sampling Rate Sampling period Display Temp Unit Display Temperature unit Input Type Input specification Range Scale Point Decimal point Special Function Special function High Low Range amp Graph Scale High Low input value and graph scale value Low Scale High Scale Lower Upper limit scale value Alarm Type Alarml1 operation mode Alarm Alarm No Alarml output alarm number Record Mode Record mode Divide Zone Record zone division Standard Speed Standard record speed Memo Period Digital memo period Log Speed Save period Summer Time Summer time
143. y time information at right Over 2 alarms ON from 1 Records alarm sign and CH1 AL the number of alarm channel 14 00 33 form lf alarm occurs at digital memo time memo information includes alarm information Therefore as below figure alarm sign alarm information time information is not recorded and is replaced as digital memo m 11 06 16 AL 13 10 00 r 11 06 16 AL 12 10 00 0000000 Absolute value upper limit alarm Aa Absolute value lower limit alarm iy 4 Beviaton owerimitaiarn 9 T Copyright Reserved Autonics Co Ltd 75 i 8 Parameter detail setup Autonics 2 Record Mode Record mode is Digital It records alarm ON channel data information alarm abbreviation time with the set record color of corresponding channel In front of ON time as below A is marked to mean the data by alarm O CH1 BURN SB I A 12 00 00 O au gt After alarm recording if it maintains same alarm or alarm is cleared it does not record the relevant data In case of record by digital memo it prints alarm abbreviation of occurring alarm as below abbreviation 1 Absolute value upper imitam PH Deviatoniowerimtalam DL input reak ahamm SB Norecor ng paper PE It is used when printing 2 channels in one line 7 Several alarm ON Setrange OFF PV Hi PV Lo DV Hi DV Lo SBA PEND Factory default Alarm1 Type PV Hi Alarm2 Type to Alarm4 Ty

Download Pdf Manuals

Related Search

Related Contents

Samsung 2243SNX Computer Monitor User Manual  le Manuel d`utilisation Turfline  Télécharger    ElectroPrep™ System User`s Manual  Etat des lieux de la médecine générale au 1er Janvier 2013  Lumens Technology DC166 User's Manual  R-898 Operation  DA-2003P - BC Group International Inc.  Hampton Bay THD339414.2a Installation Guide  

Copyright © All rights reserved. Failed to retrieve file