Manual - FAST.Eu
Contents
1. Write down the serial number found on the rating label of the range hood in the space below It is essential that you store this user s manual in a safe place so that you can use it in the future If you intend to sell the appliance give it to another owner or if you move always make sure that the user s manual is attached to the appliance so that the new owner can also learn about the operation of the appliance and the relevant warnings SERIAL NUMBER Important safety instructions e This appliance is designed for household use only e Before connecting the power cord plug make sure the voltage stated on the rating label of the appliance corresponds to the voltage in your wall socket Connect the power cord plug to a power socket with a voltage of 220 240 V 50 Hz e Only use a properly grounded power socket The appliance may only be connected to a properly grounded power socket e All electrical connections must be performed by a qualified electrician e Installation performed by an unqualified person may cause incorrect operation damage to the appliance create a fire hazard or cause injury to persons e Neither the manufacturer nor the vendor take responsibility for damages cause by incorrect or unprofessional installation connection or operation Tampering with the appliance by an unqualified person will void the customer s right to a warranty repair e Do not expose the power cord to excessive pressure or loads do not place2. has not been damaged and that the package includes all the items described in this user s manual If the appliance was damaged during transport contact authorised service centre Do not use a damaged appliance under any circumstances IMPORTANT Ensure that children do not play with the packaging material Dimensions of the appliance 262 Min 620 Max 1000 IMPORTANT Before installing or using the appliance please first read all instructions and check that the voltage and frequency values on the rating label correspond to the voltage and frequency in your electricity grid We recommend that the appliance be connected by a service technician or another gualified person in compliance with local codes and regulations Before starting the installation e Check that the purchased appliance has the correct dimensions corresponding to the chosen installation location Furthermore ensure that there is an electrical power socket available that will remain accessible even after the range hood is installed e Before installing the range hood check that all necessary masonry work is complete e Have all electrical connections performed by a qualified person e Werecommend that you remove the aluminium filters before installing the range hood EN 5 Copyright O 2012 Fast CR a s Revision 04 2012 e Check that there are no packaging materials or other materials e g user s manual warranty card or bags with screws
3. heavy objects on it it must not be tangled and it must not be stepped on Do not locate the power cord in or on heat sources such as stoves heating or other generators of heat Otherwise this may damage the power cord or create a fire hazard e Only connect the power cord plug to a power socket after the entire installation is completed e The power plug serves as a disconnection device and for this reason the power socket must remain easily accessible for the event of a dangerous situation unless it is connected into a terminal box e Do not touch the lights if the appliance has been running for some time Lights heat up during operation and may cause burns e This appliance is designed for fume extraction during standard domestic use Do not use the appliance for purposes other than those for which it was designed Otherwise you expose yourself to the risk of a dangerous situation and voiding the warranty Follow the instructions for installation and ventilation with the exception of when a fire stove is used Do not use the flamb cooking method under the range hood Regularly replace the filters in the range hood Otherwise this presents a fire hazard Only use filters suitable for use with the range hood The manufacturer or distributor will recommend the suitable filter type e Do not use the appliance without the aluminium filter inserted Do not take out the filters while the appliance is on e Regularly clean the appliance to pre
4. using the range hood without an air exhaust it is necessary to use a carbon filter The carbon filter is not included Contact your vendor or an authorised service centre to purchase this filter e Before installing or replacing the carbon filter check that the appliance is turned off and disconnected from the power socket or that the respective circuit breaker is turned off e tis necessary to replace the carbon filter regularly every 3 5 months depending on how much the appliance is used e Never wash the carbon filter in water unless the manufacturer states otherwise e Aluminium filters must always be installed even when the carbon filter is not installed Do not use the appliance without the aluminium filter installed Replacing the carbon filter 1 For the correct operation of the appliance it is necessary to install a carbon filter The number and type depends on the model 2 Place the carbon filter on the motor outlets and turn it in the clockwise direction 3 Toremove the carbon filter turn it in the anticlockwise direction Ventilation To ensure proper ventilation leave windows closed while the appliance is turned on WARNING Pay increased attention if you are using the appliance together with another appliance that uses air or fuel for its operation e g heating fan fan etc or that uses gas coal or wood as its operation may negatively affect the performance of the range hood because it expels air out of the
5. your local retailer when buying an equivalent new product The correct disposal of this product will help save valuable natural resources and help in preventing the potential negative impact on the environment and human health which could be caused as a result of improper liquidation of waste Please ask your local authorities or the nearest waste collection centre for further details The improper disposal of this type of waste may fall subject to national regulations for fines For business entities in the European Union If you wish to dispose of an electrical or electronic device request the necessary information from your seller or supplier Disposal in other countries outside the European Union If you wish to dispose of this product request the necessary information about the correct disposal method from local government departments or from your seller This product meets all the basic EU regulation requirements that relate to it Changes to the text design and technical specifications may occur without prior notice and we reserve the right to make these changes EN 18 Copyright 2012 Fast R a s Revision 04 2012
6. M0d w LO 60 OL 30 L 0 SI LO v abeyJon Er 05 vs 8b Sly o er zr Er ap 242 9SION SEZ SoZ 061 08L sol DEZ soz 007 OZ HUILA anss id m 067 SLL 00 OLE St soz OLE 097 y U1 Moy Aly m SZL S6 OLL 041 06 DEl 071 SZL M 19MO4 o 90 90 60 ZL 90 90 60 90 Y aBerjon SE by Sy Ov Er L 6 SE 9 ap ana 3sl0N SSL 08L 091 091 OSL OLL SSL OEL Oz Hu anss id m 017 SSL 061 057 061 007 OEZ 081 y U1 Moy Aly m OLI 08 08 SEL OL 071 06 SOL M 42M0q so 90 90 L so so 90 so v aBe3jon 9019 Did L0S9 Ad SOv6 Ad 8029 82d oops aq 2 79 934 Zoss 334 sov9 Dad lad mad t to change is subjec d data i tone All the here ment NOTE EN 17 Revision 04 2012 Copyright O 2012 Fast CR a s INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS Dispose of packaging material at a public waste disposal site DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES CE The meaning of the symbol on the product its accessory or packaging indicates that this product shall not be treated as household waste Please dispose of this product at your applicable collection point for the recycling of electrical amp electronic equipment waste Alternatively in some states of the European Union or other European states you may return your products to
7. RANGE HOOD USER S MANUAL PHILCO ES Samous for Quality the World Over PEW 67101X PEW 97101X Dear customer Thank you for buying a PHILCO brand product So that your appliance serves you well please read all the instructions in this users manual CONTENTS PART 1 IMPORTANT SAFETY INSTRUCTIONS 000000000000000000 0000000000000000 00000000000000 naen s nn ssa nenen ene nne nnnnenn 2 PART 2 DESCRIPTION OF THE APPLIANCE 000000000000000000000000000 000000000000 a 0000 Rss nn sos sn n s naen eeno 4 PART 3 INSTALLATION e s0sssosnsonono nooo sos RR 065945965586 a5anga598 5 UNPACKING as otroci dana o 5 Dimensions of the appliance Placement Installation Carbon ile aaa rail No 12 Ventilaci n anio sicario 12 PART 4 OPERATION Operating tips PART 5 MAINTENANCE AND CLEANING 0c0000000000000 0000000000000000 00000000000000 ee nen one eea ene nane anane co s ass 14 Changing a light bulb Cleaning PART 6 BEFORE YOU CALL THE SERVICE CENTRE 00000000000000000000000 0000000000000000 00000000 0n0n0eene nne nanenennenanene 16 PART 7 TECHNICAL SPECIFICATIONS 0000600000000000 000000000 0000000000000000 00000000000000 0ne anane ne ane nne nean anane annanenanane 17 EN 1 Copyright 2012 Fast R a s Revision 04 2012 PART 1 IMPORTANT SAFETY INSTRUCTIONS Recommendation Carefully read these instructions before installing and operating this range hood
8. RANGE HOOD MAY ONLY BE CONNECTED TO THE ELECTRICAL GRID AFTER THE ENTIRE INSTALLATION IS COMPLETE Supplied accessories depending on the model N A non return exhaust flap must be installed into the air outlet of the range hood unless one is already factory installed Placement ENS Min 65 cm lt 1 Min 75 cm v tt d Install the range hood at a height of at least 65 cm above an electric cooktop or at a height of 75 cm above a gas cooktop EN 6 Copyright 2012 Fast R a s Revision 04 2012 Installation 1 Installation of hanging brackets To hang the range hood it is necessary to first install 2 L shaped hanging brackets which are supplied together with the screws on to the range hood according to the illustration below Then secure the brackets using appropriate M5 x 35 screws into an M5 thread i NS N SS M5 x 35 screws Hanging bracket 2 Installation of the non return exhaust flap Install the non return exhaust flap on to the top part of the range hood using 3 5 x 9 5 screws according to the illustration below EN 7 Copyright 2012 Fast R a s Revision 04 2012 3 Drilling mounting holes Place the installation template against the wall and drill holes in points A B and C using a drill bit with a diameter of 10 mm To install the chimney drill holes using a drill bit with a
9. diameter of 6 mm adhering to the dimensions for the minimum and maximum height For 80 90 cm models drill holes designated at G H WARNING When drilling the mounting holes used for hanging the range hood ensure the holes have the correct diameter If the holes are drilled incorrectly then the correct assembly of the range hood will not be possible 4 Inserting dowels Into the drilled holes A B and C with a diameter of 10 mm insert dowels with a diameter of 10 mm Into the two holes with a diameter of 6 mm insert dowels with a diameter of 6 mm see illustration below For 80 90 cm models into the drilled holes G H insert dowels with a diameter of 10 mm 10mm plastic dowel 6mm plastic dowel D Holes for connecting the exhaust diameter 6 mm E z____ s Holes for hanging the range hood diameter 10 mm E 5 Attaching the chimney plate Drill holes into the wall using a drill bit with a diameter of 6 mm Attach the chimney plate by screwing 3 9 x 22 Ysb screws into the plastic dowels with a diameter of 6 mm Into the drilled holes A B with a diameter of 10 mm with the dowels inserted screw in two 5 5 x 60 Ysb screws The distance between the wall and the head of the screw must be 5 mm 5 5 x 60 Ysb screw 3 9x 22 Ysb screw EN 8 Copyright 2012 Fast R a s Revision 04 2012 6 Hanging the range hood Hang the range hood using the hanging brackets on to the screws in holes A and B see ill
10. egularly replace the carbon filters 2 Use the medium exhaust power level Only use the highest power level when necessary 3 To ensure proper ventilation leave windows closed while the appliance is turned on EN 13 Copyright 2012 Fast R a s Revision 04 2012 PART 5 MAINTENANCE AND CLEANING WARNING Before cleaning regular or other maintenance installation or removal check that the appliance is turned off and disconnected from the power socket or that the respective circuit breaker is turned off Changing a light bulb 1 Open the split extraction plate glass 2 Take off the aluminum filter There are covers on the left and right back edges which can be used for changing the lamps on the edges Take this covers off Disconnect cables of LED lights Push onto light to remove them Remove tape between lamp and product body Remove protective tape of new lamp before placing Oy Gr gt po NOTE Do not hold the light bulb with your bare hands Dirt or sweat from the hand may shorten their lifetime Cleaning e Aluminium filters capture dust and fat from the extracted air e Itis necessary to regularly wash these filters ideally once a month depending on the level of use Wash the filters in water with dishwashing detergent or you may place the filters in a dishwasher and wash them using a gentle program max 60 C e Take out the aluminium filters by pressing the clip e After cleaning allow
11. er is not too dirty without an exhaust ATTENTION Use the range hood together with the stove This will ensure the correct air exhaust We recommend to leave the range hood running a few minutes longer than the stove to ensure that all odours are extracted EN 16 Copyright O 2012 Fast CR a s Revision 04 2012 a Z O rm lt J U LLI O a ol lt J Z T U LL PART 7 ww OZL ww OZ L ww OZ L ww OZL wu OZL ww OSL ww OSL ww OSL 493 9U121P 33 N0 ny ZH OS ZH 0S ZH 0S ZH OS gt ZH OS gt ZH OS ZH OS ZH 0S beyon andul NObZ 077 NOFZ 077 NOKZ OZ NOWE 0ZZ NObZ 0ZZ AOPZ OZZ NObZ OZ AOZ Ozz 19 709 19 gp 9n9 asION ose S9 OSE OZ HUILA aanssaid u OSZ OSZ OSL U WU MOJ aiy m 017 017 017 M 1amod ur L L L v abez oA S ES ves ES ap 9n9 asion OZE STE OLE ozHww sanssald m 0Lb SSY OSY U U Moy Aly m SLL SZL OLL M 14amog gt 80 80 80 v abeyjon 6v ES ss SS 6v zs 8b ap Jana asion 587 SZZ 007 08L 067 Ste soc oz Hua eansseid v SZE 00 005 00 09 005 SEE y U1 MOJ ny m 051 OLL 077 OLL OSL S81 Stl M 1a
12. inside the appliance These need to be taken out and kept for possible use in the future e Werecommend that you disconnect and move to the side freely standing or built in stoves so that you have easier access to the rear wall or ceiling If this is not possible place protective material on to the work area cooktop or stove This will prevent damaging these surfaces e Select an even surface for the necessary assembly of the range hood Cover the surface with a protective material and place all parts of the range hood and fastening elements on to it e tis necessary that a qualified technician inspects the suitability of the supplied fastening material and other components for the specific wall ceiling type The wall ceiling must be sufficiently strong to hold the weight of the range hood e Donotattach this range hood to a wall or cabinet furniture by tiling plastering and do not glue it on using silicone glue The appliance is designed to only be installed on a wall ceiling e We recommend that always two people perform the installation of the appliance If your range hood is designed to be mounted to the ceiling adhere to the following instructions 1 The range hood must only be suspended on ceiling beams or on load bearing ceiling beam connections 2 Donot suspend the range hood on false ceilings 3 The ceiling must have a load bearing capacity of at least 40 kg 4 The ceiling thickness must be at least 30 mm IMPORTANT THE
13. o dispose ofthem in an environmentally conscientious manner according to regulations in force During transport adhere to the symbols of the cardboard box When carrying the appliance hold it by the respective handles NOTE We recommend that you keep the original packaging at least for the duration of the warranty period for the event of repair or refund and transport to the authorised service centre Adhere to the symbols on the cardboard box If you do not have the original cardboard box adhere to the following instructions a Donot place any items on the appliance that could damage the appliance during transport b Protect the appliance against impacts falls etc c Wrap the appliance e g in bubble wrap which will protect the appliance from damage NOTE The carbon filter is not included NOTE If the building is equipped with a heat recovery system system it is necessary to setup the appliance for internal air circulation without an exhaust In that case it is necessary to purchase the carbon filter EN 3 Copyright 2012 Fast R a s Revision 04 2012 PART 2 DESCRIPTION OF THE APPLIANCE 1 Inner chimney 2 External chimney 3 Control panel 4 Lighting 5 Filter 6 Tempered glass EN 4 Copyright 2012 Fast R a s Revision 04 2012 PART 3 INSTALLATION Unpacking e After unpacking remove all packaging and advertising labels from the appliance Check that the appliance
14. room This warning does not apply if you installed the appliance without an exhaust out of the room EN 12 Copyright 2012 Fast R a s Revision 04 2012 PART 4 OPERATION Remove the protective foil from the control panel Exhaust power selection This range hood is eguipped with 5 levels of exhaust power Select the power level based on the use of the stove and the amount steam that the pots emit To turn on the motor press the button and to set the exhaust power level press the or button Press the button to increase the exhaust power and the button to reduce the exhaust power Automatic timer TIMER All models with a remote control are equipped with an automatic timer Press and hold the button at the set exhaust power level for at least 2 seconds and the automatic timer function will be turned on for a period of 15 minutes When the function is turned on the respective symbol will appear on the display and the motor will turn off automatically after 15 minutes NOTE Use the range hood together with the stove This will ensure the correct air exhaust We recommend to leave the range hood running a few minutes longer than the stove to ensure that all odours are extracted Lighting The range hood is equipped with lighting Press the button with the light symbol to turn on the lights Press the button again to turn the lights off Operating tips 1 Regularly clean the aluminium filters and r
15. the aluminium filters to dry thoroughly before reinstalling them e Wipe the outer surface of the range hood with a clean damp wiping cloth lightly dipped in water with a small amount of dishwashing detergent Then wipe dry e Avoid electrical parts coming into contact with water or another liquid e For cleaning you can also use special agents for the maintenance and cleaning of INOX surfaces applies only for models with an INOX surface treatment Cleaning the aluminium filters The aluminium filters need to be cleaned when C appears on the display depending on the model Clean the filters according to the above mentioned instructions and after reinstalling them press and hold down the fan button for 3 seconds until the C symbol depending on the model disappears from the display The symbol E depending on the model will appear on the display which means that the appliance is ready for operation EN 14 Copyright 2012 Fast R a s Revision 04 2012 If you wish to use the appliance without clearing the C symbol depending on the model press the fan button to start extraction for 1 second then the C symbol depending on the model will appear again and the motor will continue running NOTE The C symbol depending on the model appears on the display after approximately 60 hours of operation WARNING For cleaning do not use petrol benzene thinners or any other solvents coarse cleaning agents steel
16. ustration below 7 Tightening screws After hanging the range hood tighten the screws to secure the range hood in place You can use the M5 x 40 Ysb screws to fully stabilise the range hood NOTE You can use M5 screws to achieve full stability EN 9 Copyright 2012 Fast R a s Revision 04 2012 8 Tightening the hanging screws In point C see illustration below tighten the 5 5 x 60 Ysb hanging screws to ensure that it is hung safely 9 Installation of the aluminium duct tube Attach the flexible aluminium duct tube on to the air exhaust in the top part of the range hood and insert the other end into the exhaust opening in the wall Check that the connection is secure even at full power EN 10 Copyright 2012 Fast R a s Revision 04 2012 10 Installation of the outer chimney Insert the inner chimney into the outer chimney Seat the chimneys on to the base with the motor and slide downwards Check that the connection between the body and the base with the motor is secure Outer chimney 11 Installation of the inner chimney Pull the inner chimney out of the outer chimney and secure to the plate using 3 5 x 9 5 screws 3 5 x 9 5 screw Inner chimney After completing the installation check that the range hood is correctly installed and works properly EN 11 Copyright O 2012 Fast CR a s Revision 04 2012 Carbon filter If you are
17. vent a dangerous situation from occurring e Before cleaning replacing filters moving or any other maintenance turn off the appliance and pull out the power plug from the power socket or turn off the respective circuit breaker e If you are using another gas or natural gas appliance in the room at the same time the fumes from this appliance must be spatially isolated e Ifa chimney is connected to the exhaust of the range hood use pipes with a diameter of 150 or 120 mm The pipe connection should be as short as possible EN 2 Copyright 2012 Fast R a s Revision 04 2012 e Keep packaging materials out of children s reach They could suffer injury or suffocation e Children must be supervised to ensure that they do not play with the appliance If the power cord is damaged stop using the appliance Have the power cord replaced at an authorised service centre or by another qualified person Under no circumstances should you replace the power cord yourself To ensure safety use a fuse with a maximum rating of 6 A WARNING This appliance must not be used by persons including children with physical or mental impairments or by inexperienced persons unless properly trained or schooled in the safe use of the appliance or unless they have been properly supervised by a qualified person who will be responsible for their safety Attention when transporting or carrying The packaging materials are from recyclable materials s
18. wool or any sponges with steel wool WARNING You may put the aluminium filters in a dishwasher The colour of the aluminium filters may change after several washes This is normal EN 15 Copyright 2012 Fast R a s Revision 04 2012 PART 6 BEFORE YOU CALL THE SERVICE CENTRE If the appliance is not working as it should check the following recommendations for resolving the most common problems If the problem persists or it is not included in the table below turn off the appliance and disconnect it from the power socket and contact an authorised service centre Problem Solution The range hood is not working Check that the power plug is properly inserted in a properly grounded power socket with the parameters 220 240 V 50 Hz Check that the motor power switch is in the On position The lights are not working Check that the power plug is properly inserted in a properly grounded power socket with the parameters 220 240 V 50 Hz Check that the motor power switch is in the On position Check whether the light bulb or fluorescent tube is broken Exhaust power is weak Check whether the aluminium filters are dirty Check the air outlet it should be open Check whether the carbon filter is not too dirty The range hood does not extract Check whether the aluminium filters are dirty the air directly out for models Check whether the carbon filt
Download Pdf Manuals
Related Search