Home

washing machines installation use and maintenance

image

Contents

1. Garments are felted Check the linen washing instructions as well as the program characteristics and if the washing machine use is allowed 37 TILTING MACHINE USE In case the machine is equipped with the tilting system the following instructions must be also observed In this case programs are managed by a remote a control E101102X rev2 A ATTENTION When the machine is tilting or the pneumatic door is opening the user must not stay closed to the machine To control the machine use the suitable remote control OPEN CLOSE LEFT RIGHT UNLOAD ROTATION Always wait for the program end before to action the tilting function The remote control use is switched on or off using the key switch D When the remote control is activated microprocessor of the machine is deactivated The activation of the remote control is signaled by the green light A the LOADING OPERATION only 2 machines owitch on the remote control Press the enabling key below left and the DOOR OPEN key at the same time to open the door When the door is completely opened tilt backward the machine pressing at the same time the enabling key C and the key LOAD UP When the machine loading is finished bring again the machine to the horizontal position pressing at the same time the enabling key C and the key LOAD DOWN Close the door pressing at the same time the enabling key C and the key CLOSE DOOR owit
2. One of the detergent tank from 1 to 8 is finished Replace or fill the relative tank 21 TANK 1 8 FINISHED The display shows POWER FAILURE While a program was running the electrical supply was interrupted When the electrical supply come back the machine wait for 40 while the alarm POWER FAILURE is flashing on the screen Touching START the program resumes from the interruption point POWER FAILURE 33 PROGRAM SET BY THE FACTORY Wash 30 C The machine is delivered with 8 program already Rinses 3 set by the factory These programs can be Spins 3 changed by the user as explain in the relative Max spin speed 1000 RPM paragraph Program description PROGRAM 1 Prewash 40 C Wash 90 C Rinse 3 Spin 4 Max spin speed 1000 RPM PROGRAM 2 Prewash 30 C Wash 60 C Rinses 3 Spins 4 Max spin speed 1000 RPM PROGRAM 3 Prewash 35 C Wash 40 C Rinses 3 Spins 4 Max spin speed 1000 RPM PROGRAM 4 Prewash cold PROGRAM 5 WOOL Prewash cold Wash 30 C Rinses 3 Spins 1 Max spin speed 450 RPM PROGRAM 6 COLD Prewash cold Wash cold Rinses 3 Spins 4 Max spin speed 1000 RPM PROGRAM 7 HOSPITAL Prewash 40 C Wash 90 C Rinses 5 Spins 6 Max spin speed 1000 RPM PROGRAM 8 VERY DIRTY WOOL Prewash cold Wash 30 C 21 E101102X rev2 Rinses 5 Spins 2 Max spin speed 450 RPM NOTE in case of low spin washing machines
3. manual themselves so they must be kept and they must follow the machine in case of sale to another user Attachments and exploded view with spare parts list can be retrieved in IMESA web site restricted area Before to access to the manufacturer technical area be sure that the machine serial number is available A ATTENTION The manufacturer declines any responsibility about possible errors contained in this manual because of printing translation or writing imprecision The manufacturer reserves itself the right to make any necessary modification to the machine without affecting any machine essential characteristic It is forbidden the copying also partially of the text or of the pictures of this manual without any previous manufacturer authorization 2 SAFETY RULES The missing observance of the below safety rules may cause damages to people things and animals The here described machines installation and maintenance must be done by authorized personnel who know the product and in compliance with EU directives of sector Reparation made in a not correct way may be dangerous for the user Before to put in service the machine this instructions must be read with high attention This document must be available to everyone is using the machine The here described machine are addressed to the professional washing of garments and linen it is forbidden any other use of the machine if not previously authorized by the m
4. is not electrically supplied A ATTENTION The air inlet on the machine back and possibly also on the machine upper panel must always kept free Air pass must not be stopped or limited D NA I BE a NE BE v h ME pi 18 LINEN PREPAIRING Machine must be loaded on the base of the serial number plate it must not be loaded with a weight higher than the one written in the technical data sheet or in the serial number plate Before to chose the most suitable program the linen need to be sorted into groups homogeneous for fibers and fabrics in order to have a uniform washing for the whole load Before to put the linen into the washing machine be sure that the linen label is authorizing the machine washing always stick to linen manufacturer indication Here below the meaning of the most common International symbols E101102X rev2 Maximum temperature 70 Mechanical action midle Maximum temperature 60 C Mechanical action soft Maximum temperature 40 C Mechanical action very soft Only hand washing Not washing 19 HOW TO LOAD THE MACHINE AND CLOSE THE DOOR The machine must be loaded following the indication given in the serial number plate The label is stuck on the machine back A ATTENTION Machine must be loaded with linen which is the most homogeneous possible The weight of the loaded linen must not be higher than the one indicated in the technical data sheet and in the s
5. tension different from the one provided please contact the manufacturer A ATTENTION All washing machines are equipped by a speed control operated by an inverter a protection through RCD B kind device must be provided sensitive to average current value A ATTENTION In case the electrical supply come from a diesel generator then the inverter ask for the application of an additional inductor 10 HYDRAULIC CONNECTION LOAD The washing machines are equipped with electrovalve for the cold and hot water loading in 04 07 11 case it is requested the machine is equipped with a third electrovalve for hard water Each water inlet is identified for connection quotes refer to technical data sheet At the beginning of each hydraulic supply a gate valve must be provided to cut the water supply to the machine at any moment in case of emergency or in case of service At the beginning of each water inlet an inspect filter must be provided It is necessary also to control the machine inlet valve filter after a short time of use overall the hydraulic system is old or not used from a long time A ATTENTION All the inlet valve must always be connected If in the supply system it is not available the hot water connect cold water also to the inlet valve called HOT WATER When more washing machine are connected to the same water line the water line must have a diameter sufficient to grand a water flow enough to sup
6. the maximum spin speed is 450 rpm The spin speed is merely indicative and can change according to the machine capacity check the G factor effective value on machine technical sheet 34 OTHER FUNCTION There are a lot of other functions which are available and which are updated very often Enter the manufacturer s website restricted area to download the software updating files and to control the new implemented functions The following instructions are not described in this manual but are available on the web site Configuration of the coin op machine WIZARD to program the machine Pictures personalization Drum movement Program up and download Software and firmware updating USB connection SD unity Remote assistance service Parameter change while a program is running 35 WASHING MACHINE MAINTENANCE Each service must be performer only by qualified personnel Cut any supply to the machine before to proceed with any service Here below the ordinary and extraordinary maintenance operation are listed EACH DAY The machine must be kept clean using neutral detergent Clean the machine external panel in order to eliminate any detergent stain also from the detergent box Door gaskets need to be cleaned Air inlet and exhaust need to be cleaned The drum cleanness condition need to be checked be sure there are no deposits At the end of the working day the door must be le
7. the drum does not turn The alarm is reset when the screen is touched NOTE the message could contain the inverter alarm code Please contact the Authorized Service Center The display shows ALARM 03 heating timeout The maximum time to heat the water is expired The cycle does not stop but the heating steps are skipped I HEATING WDT When the screen is touched the alarm is reset Please contact the Authorized Service Center The display shows ALARM 13 Overheating The water temperature is above 110 C SRM LUNG The heating system is deactivate and the next heating steps are skipped Please contact the Authorized Service Center The display shows Maintenance request 4 MAINTENANCE It is achieved the number of cycles necessary for the maintenance request Please contact the Authorized Service Center 20 TRIPLE UNBALANCE E101102X rev2 04 07 11 DESCRIPTION WHAT IS HAPPEN WHAT TO DO The display shows WDT Zero Motor ZERO MOTOR The maximum time for the door opening is expired please contact the Authorized Service Center The display shows WDT Door closing The maximum time for the door closing is expired please contact the Authorized Service Center 16 DOOR CLOSING WDT The display shows WDT Door opening The maximum time for the door closing is expired please contact the Authorized Service Center DOOR OPENING WDT The display shows TANK 1 FINISHED
8. E101102X rev2 111111 04 07 11 WASHING MACHINES INSTALLATION USE AND MAINTENANCE INSTRUCTIONS IMESA S p A Via degli Olmi 22 31040 Cessalto TV ITALY tel 39 0421 468011 fax 39 0421 468000 www imesa it E101102X rev2 04 07 11 Index deel NIGER OTIC T ONE UT 3 2 AY oy all Ue chs DEIN M A Ed 3 MANUFACTURERRESPONSABIEIIYs uuu a Su u ana uuu aaa aigua Thasa posti 4 A UNPACKING mna mania s ae ad 4 5 INSTAEBEATIONJND JIPEAG ING dti zu Tie ated u Dan aa Su babu rave mu a Danes 5 6 MACHINE IDENTIFICATION uui uu uum pn oti aa rua eT id od Qu uiay aP S aueia aq ya a akad 5 FAN IO E mau aun u Suma Pe UPN ARE Me PRT er eee Pere nee OORT eT ee ua kanaa a maka 5 e GROUND FIXING 5 S EBBECTRICOONNEGTIOI S SS Ui RED ned dis Robe dU 7 TO FY DRAULIC CONNECTION L OAD huuu uuu a Poe PR att 8 11 AYDRAULIC CONNECTION DRAIN DU utei ee 8 12 STEAM CONNECTION acetate 8 13 COMPRESSED AIR CONNECTION a a a a a 9 14 MASCHINE START AND FINAL 9 15 EANGUAGE GEIANGOE ete iore ed u Ds c Dex reist ua aa en
9. P BEFORE nsert a STEP AFTER STEP PRIMA STEP DOPO j SCARICC SCARICC SCARICO On the screen appears the sequence of available steps it is possible to scroll the sequences using the key H Select the step and confirm your selection with OK or touch to exit from this menu Steps added before or after the blue selected steps have default value which can be modified following the previous given instructions It is also possible to insert some blocks before or after the selected step A BLOCK is a prearranged sequence of step it means that it is a complete cycle All the functions described in case of the single step are available also in case of the selection Insert a BLOCK BEFORE Insert a BLOCK AFTER 04 07 11 FREDDO Once a block is selected the parameters of the step forming this block could be modified at will 31 EASY PROG It is a simplified procedure for the construction of a new program To enter in this function select MENU among the home selections On the screen appears Select the function EASY PROG touching the corresponding icon On the screen appears STAI PER USARE EASY PROG RISPONDI ALLE SEGUENTI DOMANDE After this message the questions about the new program configuration will appear on the screen one after the other At each question answer selection one answer among the on
10. Y ala a D 21 34 OTHER FUNCTION OQ Qu siete ua Ta u aska 22 35 WASHING MACHINE MAINTENANCE 22 36 WASHING DEFECTS 22 MACHINE 22 39 SAFE LY DEVICES CONTROL 23 3 SC RAPPING LA u eism u gt E E eee tee 23 40 WARRANTY CONDITIONS a m uu a A u 24 1 INTRODUCTION This manual is addressed to explain industrial washing machine use It is written in compliance with actual EU directives The information here written is addressed to the installer and to the user which must fully understand them before to work on the machine The user manual must always be available to be consulted In case of missing or damaging of the manual ask to the manufacturer for a new copy The manufacturer is not responsible for any consequence coming from a not correct use of the machine because of a misreading or not complete reading of this manual The manufacturer reserves itself the right to modify the here written machine specification or characteristic without any previous notice The pictures of this manual may differ from reality for some detail which could be partially different from the one mounted on the machine Diagram and technical data may be modified without any previous notice The manual and its attachment are part of the
11. allation or in case of replacing the ground cable must be at least 5 cm longer than the others A ATTENTION 04 07 11 The machine must be connected to an efficient ground system the manufacturer refuse all responsibility in case this connection is not made following the subject regulation in force Before to start any service cut the electric supply to the machine for maintenance refer to the electric diagram inside the machine The electric diagram can be retrieved from manufacturer web site Minimum section for supply cable or ground cables expressed in are the following 1ph 3ph 3ph CAPACITY sosv 24ov 208V 240V 380V 440V Low spin High spin Low spin High spin Low spin High spin Low spin High spin Low spin High spin Low spin High spin Low spin 1ph 3ph 3ph 208V 240V 208V 240V 380V 440V Low spin High spin Low spin High spin Low spin E101102X rev2 1ph 3ph 3ph CAPACITY sosv 24ov 208V 240V 380V 440V High spin E NO 6 Low spin LI Steam or Hot Water heating mm A ATTENTION The minimum sections written in the above tables can be change in function of the cable length For cable longer than 5 mt increase proportionally the section in respect of the additional length A ATTENTION The machine connection must always be done on the base of the serial number label power supplied tension frequency For supplied
12. anufacturer Do not washed linen soaked with substances which are dangerous for the user health like poison or cancerous products Do not approach the machine with combustible or inflammable substances to avoid the risk of fire or explosion Always stick to the washing instructions of the linen label The use of this machine is forbidden to people under 16 years age Not properly done external connection to the machine release the manufacturer from any responsibility IMPORTANT NOTES Working with opened sides is forbidden In order to avoid burnings or accident it is forbidden to remove even temporarily the protection panels and the safety systems It is forbidden to introduce bars sticks or metallic objects inside the drum In case of emergency please refer always the here described procedures Each time the machine is started check always the safety device correct working It is compulsory to know the machine and how its safety devices are working A BURNS DANGERS The machine because of its nature presents burns danger Burns may be caused by A long contact with door during a high temperature program The contact with the fluxing steam parts E101102X rev2 On the machines are fixed the following labels if one of them should be damaged the user must replace it with a new identical one Near the door Machine must always be used by trained personnel and with at least one oth
13. ap electrical and hydraulic connection is at installer charge A ATTENTION Once the steam trap is connected to the machine it must be protected by the supplied iron box see the following picture The supply steam system must be realized following the next diagram Each connection between the system and the equipment must be tightness tested A machine B external system C steam supply system a WR FER pu B 2 C Py A 2 3 4 eT I j rA BU WH i gt F 1 i Direct steam heating System elements are identified as follow 1 washing machine 2 inlet steam valve supplied with the machine 3 filter 04 07 11 4 inlet steam gate valve 5 steam trap 6 check valve 7 flow control 8 exit gate valve A ATTENTION The machine can work with a steam pressure between 0 5bar and 4 5 bar Lower is the steam pressure longer is the heating time 13 COMPRESSED AIR CONNECTION Connection to compressed air is necessary only for some model check the technical data sheet oystem must be performed by qualified personnel in compliance with national and local rules in force Each connection between the system and the equipment must be tightness tested use a leak finder spray if there is any leak it needs to be repaired 14 MASCHINE START AND FINAL TEST Once the machine is installed and all connections are made it must be start
14. ch off the remote control using the key D tiltin UNLOADING OPERATION Switch on the remote control using the key D Press the enabling key below left and the DOOR OPEN key at the same time to open the door When the door opening is completed tilt the machine forward pressing at the same time the enabling key C and the UNLOAD DOWN When the machine is the unloading position press at the same time the enabling key C and 23 04 07 11 the key UNLOAD ROTATION RIGHT and or LEFT When the unload completed bring again the machine in horizontal position pressing at the same time the enabling key C and the key UNLOAD Close the door pressing at the same time the enabling key C and the key CLOSE DOOR Switch off the remote control using the key D 38 SAFETY DEVICES CONTROL Switch on the machine before to start the program always control the perfect safety devices work The user must always follow the procedure in the below table ACTION REACTION the machine must stop and wait for a new start Start a cycle and press STOP the drum must stop and the machine must switch off A ATTENTION When the machine is switch on before to start any program alias control the perfect safety devices work Press the emergency stop button 39 SCRAPPING When the machine life cycle arrives to the end please proceed with the machine scrapping fo
15. crease the end spin speed VELOCITA CENTRIFUGA FINALE Once the wished value is reached confirm it touching OK When the end spin speed is confirmed example 500 rpm also the middle spin speeds are set The middle spin speed is half of the end spin speed The next question refer to the number of rinses QUANTI RISCIACQUI Change the rinse number using the incon and Setting the number of rinse is set also the total number of spin To confirm the number of rinses example 3 touch The last question refer to the drum load E101102X rev2 gt HOME CARICO CESTELLO In this step is possible to configure a program for half load or full load example full load Setting the drum load it is set also the detergent and water level Once the drum load is selected confirm touching the icon OK The screen shows SALVA O DESCRIPTION 04 07 11 The program procedure with EASY WASH is now completed The program can be start immediately touching START in this case the program will not be saved A program delayed start can also be selected touching the CLOCK icon see the procedure in the relative paragraph In this case the program will start at the fixed time but it will not be saved To save the program touch the icon SAVE and follow the saving procedure For updates on the function and for more information please see the online
16. d dhol e vc eue Doe Sut Saa do d hes va the du u amupa sa 9 16 REMOTE ASSISTANCE SERVICE 10 TZ WASHING MAGHRINE USE L uu u eee eto teehee pd onn eu u ox ret leo dl eie u ees S tede ee 10 TO LINEN PREPARING ean tenuis c ex Soma hocce dete uwa gaya Sud oe au Leaves me ge Rr 11 19 HOW TO LOAD THE MACHINE AND CLOSE THE DOQOR menn meer retra reai 12 20 DOOR MANUAL OPENING DOS edat e deca ot 12 2 MACHINE SMVO A ON u ERR u uu 12 22 SEE PAM A PR OGRA 13 23 PREFERRED PROGRAM LIST d Etats 13 24 DEED STAR tbt cart testa 13 25 PIROGRANEXEGL FTDION uzman maina a Taasisi bag 14 26 PROGRAM PAUSE uu chuya s uuu ka dh eine UMP DE LE UMS Eier MUS 14 27 RAPIDAADVANGEP ir uu mun huk a E E 14 29 END OF WORKING DAY u uQ us usia Qani inu saa 15 LN ROCIODME 15 SU GPEROGRAMIMODIEIGATION uz ee Rut uu cui in G anual a Sasam kasus aa payaa aaa 15 j EAS FROG PRENNENT 17 92 SE EF DIAGNOSTICS manra cn tte Gasp masana Gh asna aliens 19 33 PROGRAM SET BY THE FACTOR
17. documentation 32 SELF DIAGNOSTICS The computer supply a complete diagnostics both in case of not correct working and in case of simple reports The following table refer to a list of messages which could appear on the screen It is suggested to contact the authorized service center in case one of the following messages would appear WHAT IS HAPPEN WHAT TO DO The display shows ALARM 01 Motor overheating The machine stops a buzzer is activated for 15 seconds MOTOR OVERHEATING When the screen is touched the alarm is reset and the door opens A motor overheating occurred wait until the motor cool down and start again the cycle If the alarm appears often please contact the authorized service center The display shows ALARM 02 Door open The machine stops a buzzer is activated for 15 seconds DOOR OPEN When the screen is touched the alarm is reset and the door opens The door opens while the washing program was running please contact the authorized service center The display shows ALARM 03 Temperature probe following the kind of temperature probe the displayed temperature passed from 237 C to 0 C The machine do not stop but all the heating step are skipped When the screen is touched the alarm is reset Temperature probe is damaged contact the authorized service center TEMPERATURE PROBE E101102X rev2 04 07 11 DESCRIPTION WHAT IS HAPPEN WHAT TO DO The display s
18. ed following the provided instructions Each machine part must be tested start a program and check at least one complete program The machine must be fully loaded and in case of high spin machines the unbalance end switch position must be controlled 15 LANGUAGE CHANGE When the machine is switched on for the first time interface language could be different from the one wished by the user The following procedure explains how to change the interface language Touch the icon MENU of the home page Ld PROGRAMMI PREFERITI APRI OBLO The display shows E101102X rev2 Touch the icon PARAMETERS the display shows G PASSWORD s Boao ver 1 26 ZAUJU HZUI 7 2 9 Digit the code 111111 and the display shows HOME UTENTE LINGUA MODIFICA Touch the icon MODIFICA and scroll the menu of the available languages using the keys and gt gt When the whished language appears on the screen confirm touching the icon OK Exit the configuration menu touching the icon HOME as many time as necessary to reach the home page 16 REMOTE ACTIVATION In case of models equipped with the remote assistance system the connection to the service server must be activated In order to do it check the instructions sent with the machine ASSISTANCE SERVICE 17 WASHING MACHINE USE Some machine parts must be known before to use the machine for the first time The following
19. educe to 10mm Room temperature bust be between 5 C and 40 C The room where the machine is installed need to have a sufficient air recycle A ATTENTION DO not use or stock near the machine petrol oil or any other inflammable stuff Fire or explosion may be caused A ATTENTION In case of tilting machine machine element may be in movement during the linen loading and unloading operation Refer to the technical data sheet to control the overall dimension of the parts in movement during the different position 6 MACHINE IDENTIFICATION The machine is identified by a sticker with the machine serial number model together with other information i e power and technical characteristics The label is stuck on the machine back Be sure that any supply electric hydraulic steam and compressed air matches with the label data Spare parts and or servicing need the correct model individuation Warranty automatically expires if the sticker is damaged removed missing or not readable In one of these condition installation and servicing operation may be difficult because of the machine cannot be correctly identified 7 NOISE The air noise produced by the machine gives an acoustic pressure continued and weighted of level A below 72 dB 8 GROUND FIXING High spin washing machine with capacity up to 23Kg do not need any ground fixing Machines are supplied with rubber feed which need to be screwed to the threaded
20. ens which can appear If the MOTOR label is selected the following screen appears Here it is possible to select the motor kind turning rhythm and pause and the rotation speed expressed in RPM 04 07 11 STEP 005 CARICO Livello Temperatura Exit Sx Pausa Dx 00 20 00 10 00 20 If the LEVEL label is selected the following screen appears Here it is possible to select the water level expressed in centimeters and the loading safety time WDT NOTE if the water level is 0 the LOADING TIME lose its meaning of Watch Dog Timer and assume the value of valve activation time STEP 005 CARICO Temperatura Exit At the same screen it is possible to choose the kind of electrovalve to active during the loading step COLD HOT or the BALANCE LOADING In the last case the step starts loading 1cm cold water and the hot and cold water one after the other until the fixed level is reached When the selected label is TEMPERATURE the following screen appears Here it is possible to fix the water temperature using the icons e STEP 005 CARICO Motore Livello Temperatura When the modification are completed touch the icons EXIT The display shows E101102X rev2 STEP 005 CARICO Motore Livello Temperatura Here it is possible to confirm or not the modifications All the above described functions are available also in case of nsert a STE
21. er operator in the room READ CAREFULLY THE INSTRUCTION FOR OPERATING IN CASE OF BLACK OUT AND INFORM ALL THE USERS ABOUT THEM A ELECTROCUTION DANGER Any service on the electrical parts must by operated only by qualified personnel Before to work on the machine cut off the electrical supply Power and controlled circuits can be modified only by manutfacturer personnel on the contrary the warranty condition empire On the electric board the here below warning label was stuck If this label should be damaged or unstuck it needs to be replaced by an identical one 400V A OPERATOR PSYCHO PHYSICAL CONDITIONS People using the machine must be in a perfect psycho physical condition during the working cycle the user must always assume a vertical posture in front of the machine Suddenly or not controlled movement must be 04 07 11 avoided because of the risks of dangerous knocks against the washer chassis i e during the dryer unloading The other people in the laundry room do not have to distract the operator who is working on the dryer While working the operator does not have to be distracted by TV radio or any source of distraction A ILLUMINAZIONE LIGHTING In the room where the machine is installed the lighting must be at least of 300 500 lux intensity unpleasant flashing must be avoided A ATTENTION These instructions do not cover all possible risks User must always pay high attention and r
22. erial number sticker Before to load the linen be sure that the drum is completely empty When the machine is loaded close the door A ATTENTION Be sure that no linen parts are taken between the door and the machine front panel while the door is going to be closed In case of machine without door handle just press the door against the machine until it is locked In case of machine with handle or motorized door lock the door must just drawn close the machine front in this way the closing pin enter in the correct position on the machine front When the machine is started the computer will give the command to lock the door 20 DOOR MANUAL OPENING While the cycle is running it could be possible to open the door manually without the use of the unlock key on the machine touch screen A ATTENZIONE Before to open manually the door cut the electricity supply from the main switch In case of machine without handle Open the below front panel In order to open the door pull down the string with ring on the left side 04 07 11 In case of machine with motorized locking take off the cover see the picture and insert a socket box wrench 4mm Turn right the wrench until the door opens A ATTENTION Before to supply electricity to the machine all the protections must be mounted again in the Original position 21 MACHINE SWITCH ON Turn the machine main switch in position on In case of steam heated mach
23. es on the list and confirm touching OK The selected answer correspond to the one with the focused icon the blurred icons correspond to the not selected icons The program questions sequence can be interrupted at any time touching HOME E101102X rev2 It also possible to go back to previous program step touching the icon BACK The first question ask for the necessity or not of a DESIDERI IL PRELAVAGGIO prewash cycle Select the wished icon example Prewash yes and confirm with OK Now appears the second question referring to the washing cycle temperature Set point temperature is written at the center example 40 use icons on the side to increase or decrease the temperature Confirm the value touching When the washed temperature is set prewash temperature is also set if prewash was requested in the previous step Temperature of prewash is set at the half of the washing temperature Example 20 C SCEGLI LA TEMPERATURA DI LAVAGGIO When the chosen temperature is confirmed it is asked to select the kind of washing mechanical action in our example MEDIUM The selected mechanical action impacts on prewash wash and rinse cycles because it determines the drum speed 04 07 11 SCEGLI IL MODO LAVAGGIO Confirm the selection touching The following question refer to the end spin speed Using the icons WV and A it is possible to increase or de
24. espect carefully the rules 3 MANUFACTURER RESPONSABILITY The instructions written in this manual are not replacing but completing the duties deriving from the safety and accident prevention laws With reference to what is written in this manual the manufacture is not responsible for a use of the machine against the safety and accident prevention laws in force correct machine installation missing of periodical and programmed maintenance not observance or not correct observance of this manual instructions electrical supply fault not authorized modification of the machine use of the machine by not authorized personnel 4 UNPACKING The machine must be controlled at the delivery moment any external or inside damage dues to the transport must be reported immediately to the forwarder The machine must be completely unpacked next to the installation position The packing material must not be spread on the environment but must be collect in the appropriate collecting place as per the environmental directives Using a monkey spanner take off the bolts fixing the machine to the pallet A ATTENTION Check the technical data sheet which is sent together with the machine documents to control E101102X rev2 the net and gross weight check if they meet the data of the available lifting means A ATTENTION The pallet must not be used as a normal machine support Always take dow
25. ft open to air the inside Atthe end of the day cut any supply energy or water to the machine EACH THREE MONTHS Check the efficiency of the drum belts and the drum clearing be sure that there are no deposit on the drum surface Check the drain valve cleaning Check the inlet valve and the corresponding filter cleaning 22 04 07 11 EACH YEAR The authorized service center must be contacted to Clean the machine inside Check the wiring contacts efficiency Ceck the teightness and the integrity of the rubber parts Grease the mechanical parts the one which ask for this treatment Clean the motor air inlet A ATTENTION In case of tilting machines before to start any maintenance be sure that the air circuit is completely release and that the pneumatic action mechanism cannot move even in case of no electricity supply In case of maintenance in no rest position of some parts be sure that the pneumatic action mechanisms are mechanically locked 36 WASHING DEFECTS In case the washing results is not satisfactory please check the following table PROBLEM Possible SOLUTION Check if the program ends with a spin Garments are still It is possible that some wet unbalance error occurred load correctly the linen and start a spin Garments have visible marks from the drum Check the spin speed maybe it is too high Check spin speed and the temperature of the used cycle
26. generic pictures are resuming the possible configuration 04 07 11 Point 1 detergent box access door In the lower capacity machines the three compartment prewash P wash W softner S are marked by the rubber cover inside E101102X rev2 In the higher capacity machines are available four carafes to load powder or liquid detergents Detergent loading moments and opening of detergent corresponding valve can be programmed Point 2 computer display Point 3 USB door A type Point 4 emergency stop button A ATTENTION When the emergency stop button is pressed the electrical supply to machine control is cut The display switch off and the cycle is automatically interrupted the turning drum is stopping because of inertia and the tank is emptied Emergency stop button must be pressed only in case of danger When the emergency situation is finished the stop button need to be turned right to be armed again The display switch one and the cycle stand by waiting for the START Point 5 machine door hole In the following paragraphs are described the different kind of locking system which could equipping the different models Point 6 main switch 04 07 11 kx E ES e E a serena art aaa 8 When the main switch is in position P the machine is electrically supplied When the main switch is in position O the machine
27. holes on the machine E101102X rev2 base A wrong adjusting of the feeds may cause strong vibration of the machine external structures The machine must be installed in a perfect level on a floor without any elastic reaction High spin washing machine starting from 30 kg Capacity must be fixed on the ground using four Fischer wall plugs and making them pass through the holes on the machine base Machines need to be installed in a perfect level on a floor without any elastic reaction A ATTENTION Do not insert any elastic stuff between the machine base and the floor Low spin washing machines must be ground fixed Starting from 30 Kg capacity low spin washing machines are supplied with an iron frame The frame must be let into a concrete base which is opportunely anchored to the floor Before to anchor the machine to the base be sure that the concrete set well to the ground and very important be sure that the frame is perfectly in level Place the machine in the suitable anchor holes and close all the bolts To control frame and concrete base dimension check the machine technical sheet Up to 23Kg capacity the washing machine are supplied with iron anchor screw iron anchor screw Tools necessary for installation are Hammer or electro pneumatic drill Hammer Pump for cleaning Brush Dynamometrical spanner Please follow the below described procedure Make a concrete base which
28. hows ALARM 04 Load timeout The machine stops a buzzer is activated for 15 seconds 4 LOAD WDT When the screen is touched the alarm is reset and the door opens The maximum time fixed for water loading is expired Control if the water taps are opened the filters are clean and there are no water leakage If the alarm appears often please contact the Authorized Service Center The display shows ALLARM 05 drain timeout The machine stops a buzzer is activated for 15 seconds 5 DRAIN WDT When the screen is touched the alarm IS reset and the door opens The maximum time to drain the water is expired Check if the drain system is clean If the alarm appears often please contact the Authorized Service Center If a payment input is longer than 6 second the display shows 11 111 5 COIN BLOCKED ALLARME 06 Coin blocked The alarm stays until the payment system is unblocked When the payment system works again correctly the main screen appear During the spin cycle the drum was gone out of balance CINE A balancing cycle starts and the machine attempt again the spin During the same spin more unbalance occurs the spin cycle is left and the program pass to the next cycle If the problem occurs often be sure that the drum is correctly load nominal capacity homogeneity of the load The display shows ALARM 09 Inverter Lock INVERTER LOCK A inverter lock occurred The cycle is not interrupted but
29. ine open the steam gate valve To limit water hammering cases the valve must be open slowly passing from the close position to open position in 1 minute time The emergency stop button must be in rest position control that the emergency stop was not activated during the transport or before the machine was switched off last time Before to start the machine always check the safety system refer to the related paragraph E101102X rev2 When the machine is switched on the software version as well as its release date appear on the screen for a while The software loading could ask for a minute time more or less The request of machine loading appears on the screen CARICA LA MACCHINA E CHIUDI L OBLO Load the machine as requested in the relative paragraph and close the door following the previous given instruction 22 SELECT A PROGRAM When the machine is loaded and the door is closed the main MENU screen appears PROGRAMS PREFERRED Touching the icon PROGRAMS list appears the programs PROGRAMMA 1 PROGRAMMA 2 PROGRAMMA 3 gt HOME It is possible to scroll down the program list using the bar on the right side Otherwise it is possible to go ahead line by line touching the arrows on the right side Once the wished program appears on the screen 04 07 11 touch it the line background will become blue example program 3 PROGRAMMA 1 PROGRAMMA 2 PROGRAMMA3 HOME O
30. le 4 4 Slow back per step 1 lt Start again the cycle P Slow advance per step P p Rapid advance per cycle In the middle of the below bar on the screen it is written the percentage of program advance 28 END OF WORKING DAY At the end of the working day the machine must be brought at the end of the cycle and switch off the drum must be cleaned and no linen must be left inside the drum Cut any supply to the machine using the suitable switch knife switch electricity steam compressed air Leave the door open 29 PROGRAM Program function allows to modified the existing program or to create new programs A program is composed by a sequence of steps which can be modified in anyone of their parameters 30 PROGRAM MODIFICATION To modify an existing program starting from the main menu touch the icon MENU the screen shows Touch the icon PROGRAM to enter into the 04 07 11 program area The screen shows NOTE the USB communication icons appears only if a USB key is connected and recognized by the system To change an existing program touch the icon MODIFICATION The screen shows the programs list scroll the list as explained in the paragraph referring to program selection Select the wished program the line background will become blue example PROGRAM 1 1 PROGRAMMA 2 PROGRAMMA 3 When the wished program is selected confirm the choice
31. llowing the country rules keeping separate the metallic the plastic the glass the electric electronic parts The above symbol on the appliance or on the package means that at the end of its life cycle this product must be collected separately from other waste material For this appliance waste separation follow the rules in force in the Country where the machine is installed A correct waste separation avoid dangerous impact on the environment and make easier the material recycling Unlawful disposal may caused application of administrative sanction following the rules in force in the country where the dryer is installed E101102X rev2 04 07 11 A ATTENTION In case the machine should not be more used before the dryer disposal make the door lock out of service to avoid that somebody close himself inside risking his life 40 WARRANTY CONDITIONS For the warranty condition check the manufacturer price list A ATTENTION To benefit of the manufacturer warranty condition the manual instructions must be carefully followed In particular Work always respecting the dryer use limits Maintenance must be always correctly operated The dryer must be used only by well trained personnel Use only original spare parts 24
32. n the machine from the pallet Install the machine has described in the opposite paragraph A ATTENTION The machine must be moved only when it is still fixed on its pallet and in case of forklift truck only by authorized personnel During the transport the high spin washing machines basement and cradle are blocked with locks in order to avoid shock absorber stress A ATTENTION Transport locks need to be removed once the machine is positioned and before it is supplied To take off the transport locks follow the next instructions Pictures indicate the lock type not the machine Remove frontal and rear panels Unscrew the bolts fixing the transport locks Remove the transport locks Mount again the panels in the original position Each panel must be mounted again in the original position before the machine is switched on 04 07 11 When removed the locks need to be kept and used again each time the machine needs to be moved Transport locks are not present in hard mounted machines 5 INSTALLATION AND PLACING Any placing and installation action needs to be made only by qualified personnel and respecting the instructions given in the installation manual To assure a correct machine use and working and to make easier the maintenance a at least 600mm free space need to be left all around the machine In case of installation of machine in line like in a coin op shop the side space can be r
33. nce OK is touched the selection is confirmed and the following information appears on the screen iUUUrpm IU RELAV 4 HOME Touch START PROGRAMMA 3 23 PREFERRED PROGRAM LIST From the main menu touching the icon PREFFERED it is possible to visualize two program lists the last used program list the list of program set as preferred by the user The program selection is done as described in the relative paragraph To set a program as preferred please refer to the on line manual 24 DELAYED START If you want to program a delayed start of a program select the program as described before then touch the icon COUNT The screen shows E101102X rev2 08 30 PARTENZA RITARDATA 08 30 It is possible to fix the starting time using the key and To exit from this menu touch the icon BACK When the wished time is visualized on the screen confirm it touching OK The display shows PARTENZA RITARDATA 00 53 Below the indication of delayed start a countdown is showing how many hours and minutes are missing to the automatic start The countdown can be interrupted at any time touching the icon STOP At the end of the countdown the cycle will start automatically 25 PROGRAM EXECUTION When the program is selected as described in the previous paragraph touch START to start the program The selected program is started In case the machi
34. ne is equipped with motorized locking system the door is locked at the program start this operation ask for some seconds While the operation is in execution the screen shows 21 41 34 PROGRAMMA 1 40 04 07 11 Displayed information enables the user to understand the machine working conditions while the program is running All parameters can be changed while the program is running just touching the relative icon These modifications stay valid only for the running program For more information about this function please refer to online documents A ATTENTION In case of anticipated conclusion of the cycle remember that the linen temperature may be very high A ATTENTION In case of not correct machine working switch off the equipment and call the authorized service centre 26 PROGRAM PAUSE While the program is running it is possible to put it in stand by just touching the icon PAUSE The screen shows rpm 40 21 41 21 PROGRAMMA 1 It is highlighting the soak step and its length Soak can be interrupted and the cycle started again touching the icon START During the soak the cycle can be interrupted at any moment touching STOP 27 RAPID ADVANCE To move fast inside the cycle touch the icon gt gt FFWD While the machine is in standby the screen shows E101102X rev2 PROGRAMMA 1 Here below the symbol meaning 1 4 4 Fast back per cyc
35. need to be well anchored to the floor respect the technical data sheet specification Be sure that the concrete base is well set to the ground the surface need to be perfectly in level Bring down the machine from the pallet and place it in the final position on the concrete base Through the open panels mark on the concrete base the position of the anchor 04 07 11 SCrews Move the machine to make free the area to make the holes Make the holes see the picture where the position is marked and following the data of the next table zi Lj VU e Bi Anchor screw length Fixable object thickness Drill diameter Minimum hole depth Anchor minimum hole Key fixing couple thread Extract the concrete residual from the hole using a brush using a pump make free the hole from the residual dust Place again the machine matching the washing machine base hole with the concrete base holes Introduce the anchor bolts through the washing machine base holes inside the concrete base holes Using a dynamometric spanner close the anchor screw following the data in the above table A ATTENTION Each installed low spin machine must be E101102X rev2 tested with a full load spin max speed and max load to check if There is no vibrations There is no noise There is contact or sliding point between the drum and the outer drum IMPORTANT if one of the above li
36. ply all the machine in case all of them are loading water A minimum pressure of 0 4 atm is necessary to load the water if the supplied pressure is lower the water loading time are longer Maximum water loading pressure is 8 Atm the minimum and maximum values are taking in consideration all the kind of valve mounted on the different machine size 11 HYDRAULIC CONNECTION DRAIN The electric drain valve used are a normally open kind it means that the water is drained in case of black out In case of more washing machines connected to the same drain line it must be enough to allow the correct water flow in case all the machines are draining water at the same time Drain collector must avoid that the water drained by one machine enter in the next one The washing machine drain is for gravity the drain tube must not present sinking or counterslope A 2 slope must be provided to allow a correct water flow The drain system must satisfy the local or national laws and regulation in force 12 STEAM CONNECTION In case of machine steam heated a steam connection must be provided The steam connection must be operated by qualified personnel and must satisfy the local and national rules in force Check that the steam has the same characteristics written in the technical data sheet and that all the system parts are certified E101102X rev2 The steam trap is delivered with the machine but not mounted on the machine the steam tr
37. sted problems occurs then the machine is not correctly installed Check if The concrete base is correctly at level The concrete base is well set to the floor The iron anchor screws are correctly closed 9 ELECTRIC CONNECTION The electrical connection must be realized by qualified personnel and it must comply with the local and national regulation in force A ATTENTION Be sure that the supplied tension matches with the one indicated on the machine label To connect the machine use a H05 VV F cable or superior it must be correctly dimensioned following the data label Install before the machine omnipolar disconnecting device i e a circuit breaker which need to have a contact opening that allows the complete disconnection in case one of the conditions of the over tension lll category is verified This device must comply with the subject regulation in force Check the main switch it must be in position 0 Open the electric supply door Pass the electric supply cable through the cable holder supplied with the machine The cable must be correctly dimensioned check the following table II collegamento dei cavi di alimentazione elettrica deve essere eseguito sul sezionatore di bordo macchina Following the kind of voltage written on the machine label connect the cable to the knife switch contacts following the below instructions iground bolt L1 L2 L3 phase contact N neutral At the inst
38. touching the icon OK The display shows the sequence of step making the program The steps are sorted by line At the same line are described the main characteristics of each step SCARICO SCARICO CARICO DETERGENTI CARICO To change the characteristics of the step nr 5 loading touch the line corresponding to the step The line background become blue and the a new menu is open E101102X rev2 STEP BEFORE it allows to insert a step before the selected one STEP AFTER it allows to insert a step after the selected one DELETE STEP delete the selected step CHANGE STEP it allows to modify the selected step characteristics BLOCK BEFORE it allows to insert a block of step before the selected step BLOCK AFTER it allows to insert a block of steps after the selected step PRIMA The selected function is marked by example CHANGE STEP point Programmable step are DRAIN LOAD COOLING HEATING PREWASH WASH RINSE DETERGENT DISTRIBUTION SPIN GENERIC The single step characteristics appears only if they can be modified In the example the CHANGE STEP option is selected To exit from the modification menu touch BACK To proceed touch the icon OK In the previous example the step n 5 LOADING was selected The steps parameters can be visualized touching the available labels MOTOR LEVEL TEMPERATURE The following pictures shows the scre

Download Pdf Manuals

image

Related Search

Related Contents

DeLonghi PrimaDonna ESAM 6600  Lenovo C72 User's Manual  取扱説明書 - たろうまる  Benutzerhandbuch Flex Tech Topdrive  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.