MINI-DMX 54 Channels DMX Controller
Contents
1. DOTE LICE III MINI DMX 54 Channels DMX Controller Operating Instructions Read All Instructions Before Use 1 INTRODUCTION Thank you for purchasing Dune Lighting equipment and hope you use it with great pleasure This leaflet aims to help you better understand many facets of the device and avoid any defective manipulation We recommend that you carefully follow the directions below The MINI DMX allows you to control the most of your devices while enabling complete freedom of movement In fact you can control any standard DMX512 line with this compact In addition the device can work under 9V battery Therefore you will not need to seek a power outlet before you install DMX512 controller 2 WARNINGS The device meets all European Union standards and carries the CE mark WARNINGS The adapter is powered by a hazardous voltage Leave the maintenance to skilled personnel Never make any modification in the adapter that is not described in this manual Bad handling may cause electric shock Please observe the following points e The device is powered by 9 Volts DC Never touch the inside of the device Mishandling may cause an electric shock e The unit and the adapter must be installed professionally and safely e Make sure the unit and adapter not receive a shock before e The starting and stopping frequently can damage the device e Do not operate the device the adapter or power cord if your hands are wet e Do not o2. method as provided in the directives has been t ex cut e D signation de l appareil WI xxxyyyy xxx denote 0 executed Designation of equipment Adapter Pour v rification a la conformit a la directive Basse Tension LVD 73 23 EEC modifi e par 93 68 EC les normes suivantes ont ete appiliqu es EN60950 1 2006 Pour verification a la conformite a la directive re lative a la Compatibilite Electromagnetique EMC 2004 108 EC les normes suivantes ont ete appli quees EN55022 2006 A1 2007 EN55024 1998 A1 2001 A2 2003 EN61000 3 2 2006 EN61000 3 3 2008 Les documents techniques suivants sont disponibles pour les instances competentes notice d utilisation rapports de test For verification in accordance with the low voltage directive 73 23 EEC changed by 93 68 EC the fol lowing standards were applied EN60950 1 2006 For verification in accordance with EMC directive 2004 108 EC the following standards were applied EN55022 2006 A1 2007 EN55024 1998 A1 2001 A2 2003 EN61000 3 2 2006 EN61000 3 3 2008 The following technical documentations are available for inspection operating instructions test documents DUNE SAS Markus Butzenlechner Directeur Technique U Miradoux le 10 02 10
3. number of the page which is flashing The display will indicate whether the internal synchronization is active ON or inactive OFF To set the value of ON or OFF press the button B You can change the number of active projector 1 to 9 each projector occupies 6 channels at once using the buttons UP and DOWN Press the SELECT to exit the internal synchronization 6 2 2 Manual operation You can use DMX controller to control the projectors manually using sliders This allows complete freedom of movement and function and adapts best to specific use To select the manual mode press the B The DMX controller will then display the number of page on which he is located between 1 and 9 each page having six channels which makes a total of 54 controllable channels Info The flashing dot shows the projector can be selected by using the buttons UP and DOWN You can then use the sliders to control the DMX512 line that was connected to the device Here is the table showing the Number of channels according to the page Page Controlled channels 1a6 7a12 13a18 19 a 24 25 a 30 31 a 36 37 a 42 43 a 48 49 a 54 O OO N OO OO FW N 6 2 3 Setting a scene To enter the programming mode press A button for 3 seconds The display of PROG indicates a number and blinks rapidly You can select the program number you want to edit by pressing the UP or DOWN The device records
4. up 9 programs 1 9 each containing 50 scenes 1 to 50 The display of SCENES indicates the last scene 00 means that no scene has been recorded for this program When you select the program you can choose the projector which wants to attribute the scene from 1 9 Press button B The display of PROJ will indicate a blinking dot Then select the number with the buttons UP or DOWN When the projector is selected you can adjust the values of the different sliders to program the scene which you want to record When the scene finishes click on INSERT button the scene is recorded The display SCENES increases to 01 If you want to edit a recorded scene select the programming mode Press the INSERT button to activate the selection and select a scene you want to replace with the buttons UP and Down Then press INSERT button again to add this new scene Delete the old selected one by pressing the button of DELETE twice Press the A button for 3 seconds to exit programming mode 6 2 4 Complete erasure of a program To delete an entire program all the scenes in it select the programming mode press 3 seconds on the button A Then select the program with the buttons UP or DOWN Then press the DELETE the message AL will blink in SCENES Click again on DELETE to delete all scenes Press the A button for 3 seconds to exit programming mode 6 2 5 I
5. mplementation of a program To run a program press the A button Use the UP or DOWN to select the desired program The program runs automatically and cyclically from the first to the last scene To stop a running program press the A button again If you use the sliders cross and stand you can adjust the internal synchronization between the projectors and adjust the brake time between scenes During the execution of the program you can still manually control the projectors even if these projectors are controlled in the program When the program is activated press the B and select the projector with buttons UP or DOWN As to altering the value of a slider take control of the projector that will no longer be dependent on the program If you use the buttons UP or DOWN you can control multiple projectors Press the B button to select another program To deactivate the manual control of the projectors press the B button twice When display a in the display of PROJ Press the UP or DOWN to see if more projectors are still in manual control D claration de conformit Declaration of conformity DUNE SAS Lieu dit Nicouleau 32340 Miradoux FRANCE Ce produit est conforme aux exigences relatives aux directives CE The product is conform with the basic requirements of the relevant EC directives A conformity assess Une m thode conforme d valuation aux directives a ment
6. perate the unit or unplug it immediately when 1 There is any visible damage on the device the adapter or power cord 2 A defect arises from falling or similar accident or you have a doubt about the state of the device or power supply 3 Malfunctions occur e Always use a qualified technician for repair e Do not unplug by pulling directly on the cord e We disclaim any responsibility for damage or injury resulting if the device are used for purposes of other than for which they were designed if they are not properly connected used or are not repaired by an authorized person e Keep the device and the power supply away from children e Use the original packaging to transport the device e For safety reasons never change inside of the device or power adapter 3 SPECIFICATIONS Power supply DC 9V or Battery 9V Type 6LR61 Consumption 0 7W 59mA Number of channels 54 Number of channels per page 6 Standard control DMX512 Dimensions L x x h mm 200 x 125 x 45 Weight g 1 kg Operating temperature 10 C to 50 C 4 CONTENTS OF PACKAGING 1x MINI DMX 1x Power supply 9 V 1x Manual 5 PRODUCT OVERVIEW DEE INSERT DELETE A B 6 6 o 6 DOWN SELECT mMmiNni DMH 1 6 7 1 INSERT DELETE AB UP DOWN SELECT 2 1 2 3 4 5 6 3 SCENES 4 PROG 5 PROJ 6 INPUT 7 OUTPUT 8 9V DC 9 Battery External 10 9 V Battery emm _ STAND CROSS 10 Con
7. trol Buttons Slider Control Viewing Scene Viewing Program Display projector XLR 3 Pin Female Connection DMX Output XLR 3 Pin Male Connection DMX Input Connection Power Supply Power Selector Battery Hatch Type of Battery 9 V 6LR61 6 USE OF PROCEEDS Switching on the product In the case of use on mains Connect the power supply sector Connect the power supply to the unit by the 9V DC input Place the power button on the position External benne DE External In the case of use on battery Insert a 9V battery 6LR61 in the space provided for this purpose Place the power button on the heading Battery DUNE o FES Pa ea LA i External The device will then be connected to a line containing the DMX512 compatible projectors Use of product 6 2 1 Setting up and configuration Once the controller turned on a self test will be conducted which will enable it to deliver all functions to zero When self test is complete you will get the following screen According to the type of effect of light connected to the DMX controller you can synchronize a projector to another For example you have multiple scenes came from same type of projectors which connected in cascade and want a sweeping effect chain a time of transition CROSS is active Slider No 2 To activate the internal synchronization of the projectors press and hold the SELECT button 2 seconds The display of PROJ indicates a
Download Pdf Manuals
Related Search