KCU-03 - Kutai Electronics
Contents
1. RESET STATUS O Ethernet KCU 03 SECTION 3 INSTALLATION Disconnect controller power source and follow the below illustrations to complete the installation of KCU 03 Step 1 Remove slot cover from the back of controller Step 3 Tighten the screw KCU 03 Ethernet Module Step 4 Start up the controller and operate through the controller front panel and enter system setting to program corresponding startup settings Remote operation activation The KCU 03 currently supports AMF 10 GCU 100 GCU 3000 ATS 22 ATS 33 ATS 34 and ATS PLC etc controllers The followings are the basic description of operation settings For more detail information please reference from the controller s operation manual AMF 10 amp GCU 100 ITEM DESCRIPTION Allows remote operation GCU 3000 ITEM DESCRIPTION 69 Allows remote operation ATS 22 ITEM DESCRIPTION Allows remote operation ATS 33 ITEM DESCRIPTION Allows remote operation ATS 34 ITEM DESCRIPTION Allows remote operation ATS PLC ITEM DESCRIPTION Communication ON OFF ATS PLC Setting Communication Interface Remark 1 If remote access is programmed to Remote access cancelled or turn OFFATS PLC communi2. gt gt gt gt Connecior 2 1 White Green 2 Green 3 White Orange 4 Blue 5 White Blue 6 Orange 7 White Brown 8 Brown STRAIGHT THROUGH NETWORK CABLE Connector 1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown 5 3 5 3 D D D Connector 2 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown KCU 03 Ethernet Module SECTION 5 STATUS INDICATOR amp TROUBLESHOOTINGS 5 1 Through the KCU 03 LED status indicator user can understand the current operating status STATUS DESCRIPTION KCU 03 communicating with Controller ETHERNET DESCRIPTION Green Network connected Yellow Blinking Data transmitting 5 2 Trouble shootings STATUS CAUSE OF FAILURE TROUBLESHOOTING LED Indicator KCU 03 Do not operate 1 Controller is under AUTO mode Check the status of No transition controller and if the controller is providing a failure signal please proceed to eliminate the cause of failure and reconnect KCU 03 If the problem persists please change KCU 03 or contact the nearest dealer Controller is not under AUTO mode Check the status of controller and if the controller is providing a failure signal please proceed to eliminate the cause of failure and reconnect KCU 03 If the controller is operating normally then please switch the controller to OFF mod
3. 8 155 102 Default Gateway Address 192 168 1 1 Default Subnet Mask 255 255 255 0 Port Address 5254 KCU 03 Ethernet Module Remark 1 Controller Setting Password is null at default setting we strongly recommend user to setup for security and to avoid human operational error If user forgets the security password contact with your local Kutai Electronics distributor or Kutai Electronics to obtain a universal code to login and reset the security password And if user forgets security password IP Gateway Subnet Mask Port Address and other settings contact with your local Kutai Electronics distributor or Kutai Electronics to obtain a universal code to login and reset all program settings to factory setting and re enter all required parameters and settings accordingly Remark 2 KCU 03 MAC Address is combined with 00 43 A3 00 nn nn format with Serial Number e g With KCU 03 Board Serial Number 1234 the MAC Address should be 00 43 A3 00 30 39 Straight Through Network Cable Crossover Network Cable Host Computer Connection Display Straight Through Network Cable must be used for connecting KCU 03 to HUB ROUTER and Crossover Network Cable must be used for connecting KCU 03 to a host computer Please refer to Connection Display CROSSOVER NETWORK CABLE Connector 1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown gt
4. KCU Ethernet Module status LO ee AL WENI LA DIDA HA GA HA LA CU lees LARS KUTAI ELECTRONICS INDUSTRY CO LTD Headguarters No 3 Lane 201 Chien Fu ST Chyan Jenn Dist Kaohsiung TAIWAN Tel 886 7 8121771 Fax 886 7 8121775 URL http www kutai com tw KCU 03 Ethernet Module SECTION 1 INTRODUCTION The KCU 03 is the Ethernet module that is designed to enable the Kutai Electronics genset controllers AMF 10 GCU 100 GCU 3000 to be operated and monitored remotely Via the designated operation software Please reference from KCU 03 software user manual user Can program and change parameter remotely instead of accessing program through the controller in person MAIN CHARACTERISTICS e The KCU 03 software interface is user friendly which makes it easy for user to monitor and change program setting remotely via LAN or WAN e All transmitting are encrypted and decoded with both Primary Key and Session Key e Three time log in failure will initiate automatic KCU 03 disconnection e Abnormal data transmitting over 5 seconds during remote operation also initiate automatic KCU 03 disconnection e KCU 03 is a server device which supports up to 4 users to log in simultaneously e 1 user password can be setup to program or change parameter remotely Please refer to Controller Setting Password e Supports 10 Base T transmitting SECTION 2 DIMENSION
5. cation interface user can only execute monitoring and changing system parameter and unable to execute controller command Remark 2 After Controller Parameter Password been setup on KCU 03 user must log in with such password to change controllers parameter settings SECTION 4 OPERATION For more information on KCU 03 Data link status LED indicator please reference from chapter 5 ES RESET O a Reset Button STATUS Da Status Indicator Connect Port Ethernet KCU 03 To RESET KCU 03 parameter settings please use a pin to insert RESET hole and hold data link indicator LED will turn ON for 4 seconds when indicator LED turns OFF please release the pin from RESET hole For detail default value please read below When installing KCU 03 user must update Default IP Address Default Gateway Address and Default Subnet Address or Port Address to enable connection for setup information pleases contact MIS or internet service provider for assistance For security reason we recommend user to setup or update all three settings such as Login User Name Login User Password and Controller Setting Password DEFAULT PARAMETER SETTING FOR KCU 03 KCU 03 Board Serial Number Non fixed KCU 03 Board Host Name WebModule Login User Name KuTai 1234 Login User Password KuTai pswd Controller Setting Password Default IP Address 192 16
6. e and disconnect power for a few seconds then reconnect If the problem still persists please change KCU 03 or contact the nearest dealer If the Controller is crashed Firstly disconnect power then remove all external module s Reconnect controller power and after eliminate the failure disconnect controller power again and connect KCU 03 to the controller and connect to power If the problem still persists please change KCU 03 or contact the nearest dealer
Download Pdf Manuals
Related Search