Home

Installation

1. 11 CONGLOMKB COM Please contact customer service conglomkb com or 1 877 333 0098 for further assistance Operation USING THE SLIDING SINK AND COLANDER The sliding sink C and the colander D can be placed in any location along the track 1 in the sink A The colander D fits inside the sliding sink C for easy storage USING THE CUTTING BOARD Side 1 In Sink Track Side 2 On Counter The specially designed cutting board E can be E placed in the track of the sink A Make sure side 1 faces up so that liquids drain into the sink through the handle The cutting board E can also be used on the counter In this case side 2 should face up so that liquids are caught in the edge trough INSTALLING THE BOTTOM GRID Ensure that the vanishing edge strainer basket F is already in the sink A before placing the bottom grid B The bottom grid B must be positioned with its rubber supports down Tilt the grid up so it is at a slight angle slide it into the sink A and place it so that it is sitting flat on the bottom of the sink 12 Care and Cleaning SINK SLIDING SINK AND COLANDER Your sink is manufactured with the highest grade stainless steel and will provide you many years of enjoyment with the proper care After use always rinse your sink with tap water to dilute and remove deposits Towel dry the sink after use whenever possible
2. flood freezing and normal wear Bends and warping caused by forced connections over tightened fittings and inadequate support during installation This warranty does not extend to commercial and institutional installation or use WARRANTY CLAIM PROCEDURE If a claimable defect occurs or replacement parts are needed please contact our customer service team at customer service conglomkb com or 1 877 333 0098 8 30 am 5 pm EST Monday Friday Before you make your call please ensure that you have Model number or description Proof of sale Details regarding the defect and or part number Name s and address es of the owner and or installer 3 CONGLOMKB COM Please contact customer service conglomkb com or 1 877 333 0098 for further assistance Pre Installation PLANNING INSTALLATION Inspect your unit before proceeding Check the surface for any flaws or damage including dents bends bumps or scuff marks If any damage is noticed do not proceed with installation Please return the unit to place of purchase for an exchange If there are any missing parts please contact the manufacturer for replacements You may choose to install this sink either undermount from below the counter or topmount from above the counter You must install this sink only in counter at least 36 in 914 mm wide with solid surface that has minimum thickness of at least 3 4 in 19 mm Protect the entire surface of t
3. leave mild steel or cast iron pans in your sink for extended periods of time as this can cause corrosion Do not put your cutting board in the dish washer and do not soak Never put your bamboo cutting board in the microwave CONGLOMKB COM Please contact customer service conglomkb com or 1 877 333 0098 for further assistance Service Parts If you are missing parts or if you require replacement parts please call our customer service team at customer service conglomkb com or 1 877 333 0098 8 30 am 5 pm EST Monday Friday Identify the required part s and have the part number s ready Pan Joseon Jooos 14 Imported by Conglom KITCHEN amp BATH St Laurent Qu bec H4S 2C3 1 877 333 0098 customer service conglomkb com www conglomkb com Made in China
4. PRESENZA STAINLESS STEEL wg WORKCENTER SINK INSTALLATION GUIDE AND USER MANUAL Model No QK032 Table of Contents Table of 2 9 Safety 2 Installing the Vanishing Edge Strainer 11 Warranty Operation One Year Limited Warranty 3 Using the Sliding Sink and Colander 12 Warranty Claim 3 Using the Cutting 12 Pre Installation Installing the Bottom Grid 12 Planning Installation a sis oe ee gee LI 4 Care and Cleaning nannnnnnnannnannannnnnnnnnnnnnnnnan 13 Tools Materials Required EEEE atts ap eo EEEE ETA 4 Sink Sliding Sink and 13 Parts 4 Cutting 13 Package Contents 5 Service Parts 33333 333 38333833323333333333333333333 14 Installation Undermount sssesaavsanvdanneedekrke teen 6 Safety Information READ AND SAVE THESE INSTRUGTIONS CAUTION Always wear safety goggles and gloves during installation to prevent personal injury 1 Inspect your unit before proceeding Once you unpack your unit check for chips scratches cracks dents or scuff marks If
5. any damage is noticed do not install 2 Use this unit only in the manner intended by the manufacturer If you have any questions contact the manufacturer 3 Installation work and plumbing must be done by qualified person s in accordance with all applicable codes and standards 4 Protect the entire surface during installation Warranty ONE YEAR LIMITED WARRANTY Athorough inspection must be made before installation and any damage must be promptly reported We will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation Conglom Kitchen amp Bath warrants this product to be free from defects in materials or workmanship for one 1 year from the date of purchase Proof of purchase original sales receipt from the original consumer purchaser must be made available to Conglom Kitchen amp Bath for all warranty claims This warranty is non transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the manufacturer s instructions It does not apply in the event of product damage due to the use of other than genuine Conglom Kitchen amp Bath replacement parts Replacement parts may be obtained by e mail at customer service conglomkb com or by calling 1 877 333 0098 between 8 30 am 5 00 pm EST installation error abuse misuse or improper care and maintenance whether performed by a plumber cont
6. f the sink Draw a line 2 parallel to the front edge of the counter to indicate how far back the sink should be located from the front of the counter 7 Typical setback is 3 1 2 4 in 89 mm 102 mm from the front of the counter depending on the cabinet structure the counter overhang the type of sink bowl and the deck size Ona piece of cardboard or paper draw a rectangle of the same size as the hole that you will cut out to accomodate the sink As this sink is 31 5 in x 20 5 in 800 mm x 521 mm we recommend that you use a template size of 30 in x 19 in 762 mm x 482 mm with square corners NOTE The flat mating surface of the sink that will touch the underside of your counter is 3 4 in 19 mm wide on all four sides Mark the center point 6 of the sink on the template Cut the template out of the piece of cardboard or paper 30 in 762 mm Ja amp N 3 3 31 2 4in 89 102 mm CUTTING THE COUNTER A CAUTION Always wear safety goggles and gloves when using power tools to prevent personal injury Place the template 8 on the counter with its front 2 parallel to the front of the counter 7 Ensure that it is placed so that the sink will clear all objects and the mounting hardware can be installed Make sure there is a minimum of 3 in 76 2 mm of space underneath on all four sides for the undermount clips E Place a line of tape 9 around the te
7. he product during installation to prevent damage TOOLS MATERIALS REQUIRED Measuring tape Saber saw or Jig saw Plumber s putty ESO Phillips screwdriver PARTS REQUIRED NOT INLCUDED NOTE Plastic Parts not shown to actual size flange 1 Safety gloves CAL Carpenter s square Electric drill with 3 8 in 10 mm drill bit and 1 in 25 4 mm or 3 in 76 2 mm hole saw Wrenches 2 Pipe wrench Silicone sealant LA Pencil Hacksaw Safety goggles mE Connecting Tail pipe 1 nut 1 Teflon tape gt De Supply lines 2 Pre Installation continued PAGKAGE CONTENTS min Bottom grid Prat A Sumessedsk EE o mmy Bamboo cutting board edge strainer Sramerassemy wmemdm 5 CONGLOMKB COM Please contact customer service conglomkb com or 1 877 333 0098 for further assistance Installation UNDERMOUNT INSTALLATION CREATING THE TEMPLATE NOTE Undermount sinks are mounted from below the counter If you are installing a topmount or drop in sink please see topmount installation on page 9 It is highly recommended that undermounting be performed by a professional installer Improper installation will void the warranty Using carpenter s square draw a line 5 from front to back on the bottom of the counter to indicate the location of the center o
8. his sink is 31 5 in x 20 5 in 800 mm x 521 mm the cut line should be 30 3 4 in x 19 3 4 in 781 mm x 501 mm 303 4in gt 781 mm 19 3 4 in 501 mm Corner radius 1 2 in 12 7 mm 9 CONGLOMKB COM Please contact customer service conglomkb com or 1 877 333 0098 for further assistance Installation continued INSTALLING THE SINK NOTE Install the faucet according to the manufacturers instructions before this step Install the vanishing edge strainer according to the instructions before completing this step See page 11 Apply silicone sealant not included around the underside of the lip of the sink A on all four sides Carefully lower the sink A into the counter ensuring that the factory installed topmount clips H do not catch on the counter edges Slide each topmount clip H along the rails so that they are evenly spaced around the sink A Swing the clamps on the topmount clips H and tighten the screws progressively see tightening sequence below until the sink rim is flush with the counter Check the alignment as you tighten so that the front of the sink A is parallel to the front of the counter Adjust and re tighten if necessary Do not over tighten Wipe away any excess sealant with a rag 6 2 4 9 7 10 8 3 5 1 Tightening sequence for clips i Q HES ae SUPPLY LINES NOT INCLUDED The supply lines which co
9. ip of the sink Faucet hole 7 CONGLOMKB COM Please contact customer service conglomkb com or 1 877 333 0098 for further assistance Installation continued INSTALLING THE SINK NOTE Install the faucet according to the manufacturers instructions before this step Install the vanishing edge strainer according to the instructions before completing this step See page 11 Putthe threaded inserts on the bolts of the undermount clips J loosely in the holes that you drilled for them in the underside of the counter Ensure that the clamps of the undermount clips J are turned so that they do not interfere with the placement of the sink Place a small bead of silicone sealant not included around the upper lip of the sink Carefully place the sink A into its location under the counter lining up the pencil marks on the lip of the sink that you made when you tested the fit of the sink Carefully rotate the clamps of the undermount clips J over the clamp bar on the sink A and gently tighten the bolts see tightening sequence below of the undermount clips J working from side to side to fasten the sink A firmly Recheck the alignment visually from above Wipe away any excess silicone and for best results allow the bond to rest undisturbed for 8 hours or overnight Install the counter as directed by the manufacturer and install all other plumbing as requ
10. ired 3 5 1 Tightening sequence for clips SUPPLY LINES NOT INCLUDED The supply lines which connect the faucet to the household water system are not supplied with this unit They need to be purchased separately Follow the supply line manufacturer s instructions for proper installation Installation continued TOPMOUNT INSTALLATION CREATING THE TEMPLATE CUTTING THE GOUNTER NOTE Topmount sinks are dropped into the counter from above If you are PN yere ped erd n d installing an undermount sink please see undermount installation 9p p jury on page 6 Using an electric drill with a 1 in 25 4 mm hole saw Place the sink A upside down on the counter Center the carefully drill four holes 3 inside the cut line sink A on the counter so that it is parallel to the front of the counter ensuring that it will not interfere with the inside structure of the cabinet or the counter It must clear the overhang of the counter and the front inside face of the cabinet Trace the outline of the sink A with a pencil Insert the sink A into the cut out in the counter to test the fit Make adjustments to the cut out if necessary Use saber saw or jig saw to cut along the cut line 2 Place a support underneath the cut out portion of the counter to prevent it from falling during cutting Draw a new line 2 3 8 in 9 5 mm inside the first line 1 This will be the cut line As t
11. mplate and trace the template onto the tape with a pencil Double check the location of the cut line before removing the template Use a saber saw jig saw to cut along the cut line Place a support underneath the cut out portion of the counter to prevent it from falling during cutting ETE Installation continued DRILLING THE HOLES FOR THE UNDERMOUNT CLIPS A CAUTION Always wear safety goggles and gloves when using power tools to prevent personal injury the underside of the counter mark the location of the ten holes 5 for the undermount clips J These holes should be equally spaced around the perimeter of the cut out with three on each side 2 and 4 and two on each side 1 and 3 They should be set back from the cut out opening by 1 1 4 in 32 mm Using an electric drill with a 3 8 in 10 mm drill bit drill each hole so that it is 3 8 in 10 mm in diameter and 5 8 in 15 8 mm deep TESTING THE FIT OF THE SINK Place the sink A underneath the cut out in the counter to test its fit Ensure that the reveal is equal on sides 1 and 3 when viewed from above There should also be at least 4 10 in 11 mm of deck revealed on side 2 to accomodate the slide of the cutting board E Make adjustments to the cutout if necessary When you are satisfied with the location of the sink A mark the location of the edge of the counter cut out on at least two sides of the l
12. nnect the faucet to the household water system are not supplied with this unit They need to be purchased separately Follow the supply line manufacturer s instructions for proper installation Installation continued INSTALLING THE VANISHING EDGE STRAINER NOTE If you are installing a garbage disposer not supplied do not install the strainer You will need to purchase from Conglom Kitchen amp Bath an adaptor This will replace the flange from your garbage disposer Install the garbage disposer according to the manufacturer s installation instructions replacing the flange for the adaptor Apply a small amount of plumber s putty not included in the notch around the drain hole of the sink Connect the upper strainer body G2 and the strainer ring G3 and insert them into the drain hole from the top of the sink Connect the strainer gasket G4 and lower strainer body G5 and insert them into the drain hole from underneath the sink Insert the strainer screw G1 through the entire assembly from the upper strainer body G2 to the lower strainer body G5 Tighten with 1 Q Not supplied a Phillips screwdriver Connect the plastic flange 1 and tail pipe 2 and thread the connecting nut 3 through the tail pipe and flange up to the lower 2 strainer body G5 Lock the connecting nut by hand NOTE 3 O Not supplied The plastic flange 1 tail pipe 2 and connecting nut 3 are not supplied
13. ractor service provider or member of the purchaser s household The warranty excludes damage due to aggressive air or water conditions harsh or abrasive cleaners and or materials Under no circumstance shall we be held liable for personal injury or property damage resulting from improper installation or use of this product We will not be held liable for inconvenience caused by loss of use of this product costs incurred for labour or materials removal and installation of replacement units or any other incidental or consequential damages Costs relating to obtaining access for repair or replacement are the responsibility of the user Our obligation shall be limited to the repair or replacement of a unit at our discretion that may prove by our sole examination to be defective under normal use and service during the warranty period Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty These non warrantable items include but are not limited to Improper installation not in accordance with manufacturer s instructions Dents and or scratches incurred during shipping handling or installation Change in colour or finish due to chemical usage Damage caused by failure to follow care and cleaning guidelines including damage caused by the use of abrasive cleaners Alterations made to the unit by the purchaser or installer Damage caused by accidental impact fire
14. to prevent water spots Should water spots occur clean with a mild solution of vinegar and water followed by a thorough rinse Use liquid soap a general household cleaner or a weak solution of vinegar and water for regular cleaning Only use plastic scouring pads recommended for use in stainless steel sinks and only use them in the bowl of the sink Scrub in the direction of the grain original polish lines CUTTING BOARD Before using your new bamboo cutting board oil with mineral oil Apply oil to your cutting board with a cotton cloth Rub in thoroughly Let board sit for approximately 15 20 minutes before removing excess oil Then apply oil once a month for light usage and up to once a week for boards that are used more often After each use wash your bamboo cutting board with a mild dish detergent and warm water Wipe board dry immediately after use Sanitize your board after coming in contact with raw meat by using a solution of vinegar or hydrogen peroxide and water or a bleach dilution Be sure to rinse board thoroughly Do not allow any food detergent soap or grease to dry or sit for extended periods of time on the surface of the sink Never use abrasive cleaning products as they will dull and scratch the finish Do not use scouring pads on the deck as they will dull the mirror finish Never use steel wool pads as they will leave iron particles on the sink which will cause corrosion Never

Installation

Contents

Download Pdf Manuals

Related Search

Related Contents