Home

20G020-00 E5 User Manual - Diamond Point International

1. 47 Stats LEDS osse ra Bias bet PDAS SAM QE S denn 52 Error codes signaled by board management controller via GED flashes ioci ook e ib on dee x debe me tduk de 52 SMBUS de VICES sankss aces ENS ERU oes Eom doe heste gro 85 PCI Express Root Port Interrupt Mapping for Downstream Devices 85 Getting Started 1 Getting Started This chapter gives an overview of the board and some hints for first installation in a system 1 1 Map of the Board Figure 1 Map of the board front panel S to OT MEN Mikro Elektronik GmbH 18 20G020 00 E5 2014 01 21 Getting Started Figure 2 Map of the board top view with CompactFlash board versions 02G020 00 and 01 CompactFlash Display Port Connectors USB Connectors Heat Sink Ethernet Connectors Battery M12 Connector for Ethernet optional MicroSD Figure 3 Map of the board top view with mSATA disk board versions 02G020 02 and 03 mSATA microSD bottom Display Port Connectors USB Connectors Heat Sink Ethernet d Connectors i Battery M12 Connector for Ethernet optional MEN Mikro Elektronik GmbH 19 20G020 00 E5 2014 01 21 Getting Started CompactPCI Serial Connector P6 Display Port Connectors USB Connectors Ethernet d Connectors i M12 Connector for Ethernet optional MEN Mikro Elektronik GmbH 20 20G020 00 E5 2014 01 21 Getting Star
2. PIC 10 APIC Mode Enabled FACP RTC S4 Wakeup Description Value only for ACPI Enable Disable for S4 Wakeup from RTC Options Enabled Disabled APIC IO APIC Mode Description This item is valid only for WIN2k and WINXP Also a fresh install of the OS must occur when APIC Mode is desired Test the IO ACPI by setting item to Enable The APIC Table will then be pointed to by the RSDT the Local APIC will be initialized and the proper enable bits will be set in ICH4M Options Enabled Disabled Extra Bus Reserved Description Extra Bus reserved for bridges behind PCI E Root Bridge Options Enabled Disabled Active Management Technology Support Intel AMT Support Enabled Intel AMT Setup Prompt Enabled Intel AMT SPI Protected Disabled Intel AMT Password Write Enabled HECI Timeout Enabled AMT Wait Timer Lit Unconfigure ME Disabled Verbose Mebx Output Enabled USB Configure Enabled PET Progress Enabled e Local FW Update Enable Enabled e Local FW Qualifier Always ASF Support Enabled atchdog Support Disabled OS Timer 0 BIOS Timer 0 Intel AMT Support Description Enable disable Intel Active Management Technology BIOS exten sion Note iAMT H W is always enabled This option just controls the BIOS extension execution Options Enabled Disabled MEN Mikro Elektronik GmbH 66 20G020 00 E5 2014 01 21 BIOS Intel AMT Setup Prompt Description Enable or
3. gt Platform Thermal Configuration Shut Down Temperature LIZO CI Throttle on Temperature LSO CI TC LZ T2 LSI TIPS 10 gt CPU Thermal Configuration DTS Enabled Thermal Mode TM1 and TM2 ACPI 3 0 T States Disabled gt Intelligent Power Sharing ntelligent Power Sharing Enabled CPU Turbo Enabled MCH Turbo Enabled Shut Down Temperature Description ACPI Critical Trip Point the point at which the OS will shut down the system Options 70 C 75 C 80 C 85 C 90 C 100 C 110 C 120 C Throttle on Temperature Description Set the CPU temperature point of Throttle on Options 40 C 45 C 50 C 55 C 60 C 65 C 70 C 75 C 80 C 85 C 90 C TC1 TC2 Description Thermal constant TC1 for the ACPI Passive Cooling CPU Throt tle On Formula Cannot be changed TPS Description It represents in 10th of a second how often the OS will read the temperature when Passive Cooling is enabled Cannot be changed MEN Mikro Elektronik GmbH 63 20G020 00 E5 2014 01 21 BIOS DTS Description Enables CPU Digital Thermal Sensor function Out of spec ACPI Thermal Management uses EC reported temperature values and DTS SMM is used to handle Out of Spec condition Options Critical reporting Disabled Enabled Thermal Mode Description Setting this bit enables the thermal control circuit portion of the CPU Intel Thermal Monitor TM1 50 duty cycle TM2 Enhanced Intel Speed Step Options Disabled T
4. 2014 01 21 Functional Description 2 8 2 3 Inserting and Extracting a microSD Card on the Ethernet Rear I O Card The Ethernet rear I O card e g GM1 also offers a microSD card slot To install a microSD card please stick to the following procedure M Power down your system and remove the G20 from the system M Put the board on a flat surface M Insert the microSD card into the slot with the contacts at the top MZ Make sure that it clicks into place properly M For extracting the card push it down and pull it out MEN Mikro Elektronik GmbH 30 20G020 00 E5 2014 01 21 Functional Description 2 8 3 mSATA Disk The G20 is shipped without an mSATA disk installed Please see MEN S website for ordering options 2 8 8 4 Installing an mSATA disk To install an mSATA disk please stick to the following procedure M Power down your system and remove the G20 from the system M Put the board on a flat surface M Insert the mSATA disk carefully in a 30 angle MI Make sure that all the contacts are aligned properly and the card is firmly con nected with the card connector MEN Mikro Elektronik GmbH 31 20G020 00 E5 2014 01 21 Functional Description M Fix the card using two M2 5 x4 screws highlighted in red mSATA microSD bottom Heat Sink MEN Mikro Elektronik GmbH 32 20G020 00 E5 2014 01 21 Functional Description 2 8 4 Serial ATA SATA The serial ATA SATA interface is controlled by the
5. F10 Save and Exit menu TPM Status Description TPM Trusted Platform Module Status Not supported on the Axxx Options Not installed Supervisor Password Description Shows whether a supervisor password has been entered User Password Description Shows whether a user password has been entered Set Supervisor Password Description Enter and confirm the supervisor password under this menu item To delete the password enter an empty password MEN Mikro Elektronik GmbH 73 20G020 00 E5 2014 01 21 MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 TE IOS Power On Password Description Select when the password has to be entered Options Enabled The password has to be entered when the system starts Disabled The password has to be entered when changing to the setup menu User Access Level Description Set the User Access Level Options View Only Access to InsydeH20 Setup allowed but the fields cannot be changed Full Any field can be changed except the Supervisor password Limited Only limited fields can be changed Set User Password Description Enter and confirm the user password under this menu item Clear User Password Description Clear the user password Only possible for a supervisor or user in the access levels full or limited 3 4 Power InsydeH20 Setup Utility Main Advanced Security Power gt Advanced CPU Control gt Platform Power Management gt Break Event ACPI S3 Enabled Wak
6. F9 Setup Defaults F10 Save and Exit On the first BIOS setup configuration this loads safe values for setup which make the board boot up MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 BIOS 3 6 5 Load Custom Defaults If this option is selected the custom defaults that have been saved in a former session with Save Custom Defaults see Chapter 3 6 6 Save Custom Defaults are loaded 3 6 6 Save Custom Defaults Save custom defaults 3 6 7 Discard Changes Discard changes MEN Mikro Elektronik GmbH 84 20G020 00 E5 2014 01 21 Organization of the Board 4 Organization of the Board 4 1 SMBus Devices Table 18 SMBus devices Function SMB Address SMB Address Hex Clock generator 1101 001x OxD2 OxD3 SPD EEPROM 1010 000x OxAO memory channel A SPD EEPROM 1010 010x OxA4 memory channel B Board EEPROM 1001 111x OxAE Protected register 0110 010x Ox6E Temperature sensor 0011 010x Ox3E 1 The first address is for write command the second for read command 4 2 PCI Express Root Port Interrupt Mapping Table 19 PCI Express Root Port Interrupt Mapping for Downstream Devices Port INTA INTB INTC INTD 1 INTA INTB INTC INTD 2 INTB INTC INTD INTA 3 INTC INTD INTA INTB 4 INTD INTA INTB INTC 5 INTA INTB INTC INTD 6 INTB INTC INTD INTA 7 INTC INTD INTA INTB 8 INTD INTA INTB INTC MEN Mikro Ele
7. TA_Tx END 8 6_SATA 6_SA 6_SATA 6_SA 5_SATA 5_SATA 5_SA 5_SA END _Rx TA Rx CND Tx TA Tx END Rx _Rx CND TA_Tx TA_Tx 7 4_SA 4_SATA 4_SATA 4_SATA 3_SATA 3_SATA 3_SA 3_SA TA Rx _Rx END Tx _TX SUE Rx _Rx END TA Tx TA_Tx END 6 Note The signals written in gray are specified in the CompactPCI Serial specification but not supported on this board MEN Mikro Elektronik GmbH 44 20G020 00 E5 2014 01 21 Functional Description LLI LIELELLLI 1 mE NM OE ENDE 07 97 EISE 8 6 PE 6 PE 5 PE T amp PE amp PE 6 PE 6 PE END RxO1 RXO1 GND Tx Tx END Rx00 Rx00 GND TX00 Tx00 7 oF EE gt gt EE gt PE Be gt gt PE ROM 6 5 PE 5 PE SPE 5PE 5PE 5 PE_ 5_PE_ END x01 3x014 GND Tx TX CND Rx00 Rx00 EE TX00 Tx00 3 EXE E BM t CC BSUN 4E EO 4 4 PE 4 PE 4PE 4 PE 4 PE 4PE 4 PE 4 PE END Rx01 2x01 GND D Tx01 END Rx00 Rx00 END Tx00 Tx00 3 anp PE 3 PE_ enp SPE 3PE cnp 3 PE 3 PE_ enp 2 3PE 3 PE 3 PE 8PE 3PE 3 PE 3PE END Rx01 1x014 SE x Tx01 CND Rx00 Rx00 CND Tx00 Tx00 L K J l H G F E D C B A Note The signals written in gray are specified in the CompactPCI Serial specification but not supported on this board MEN Mikro Elektronik GmbH 45 20G020 00 E5 2014 01 21
8. in Power button GA2 GA3 Geographical addressing WAKE_IN in Wake signal IPMB_SDA in out 2C system management bus data IPMB SCL out lC system management bus clock Power 12V in 12 V power supply GND Digital ground STNDBY in Standby voltage SATA x_SATA_Tx out Differential pair of SATA transmit lines port 1 X SATA Tx to port 8 X SATA Rx in Differential pair of SATA receive lines port 1 X SATA Rx to port 8 SGPIO SATA SC out Clock signal SATA SL out Last clock of a bit stream begin a new bit stream on the next clock SATA SDO out Serial data output bit stream SATA SDI in Serial data input bit stream may not be sup ported by all SGPIO devices PCI x PE Rx00 x PE Rx07 out Differential PCI Express receiver lanes 0 to 7 Express x PE Rx00 x PE Rx07 for link 1 and 2 x 1 or x 2 x PE Tx00 x PE Tx07 in Differential PCI Express transmitter lanes 0 x PE Tx00 x PE Tx07 to 7 for link 1 and 2 x 1 or x 2 x PE Rx00 x PE Rx03 out Differential PCI Express receiver lanes 0 to 3 x PE Rx00 x PE Rx03 for link 3 to link 8 x 2 3 to 8 x PE Tx00 x PE Tx03 in Differential PCI Express transmitter lanes 0 x PE Tx00 x PE Tx03 to 3 for link 3 to link 8 x 3 to 8 x PE CLK x PE CLK out Differential 100 MHz reference clock for link 1 to 8 x 1 to 8 PE CLKEH in Presence Detect MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 Functional Description Digital Dis play 1 DD
9. 00 E5 2014 01 21 DENEN Functional Description 2 14 Reset Button The G20 is equipped with a reset button which is recessed within the front panel and requires a tool e g paper clip to be pressed preventing the button from being inadvertently activated 2 15 Status LEDs The G20 provides four status LEDs at the front panel which are controlled by the board controller using SMBus commands Table 16 Status LEDs LED No Color Name 1 e Board Status LED 2 e Hotswap LED 3 e User LED 4 e User LED 2 15 1 Status LED The yellow status LED shows board status messages The LED is controlled by a GPIO pin of the board controller It is switched on when the BIOS starts switched off when the board is switched off and flashing when the board is in stand by S3 status During normal operation the LED can be switched on and off using the MEN driver forthe board controller See MEN s website for further information In case of a board failure the LED displays the following error messages Table 17 Error codes signaled by board management controller via LED flashes Number of Flashes Error V3 3A failure Input voltage failure External power supply failure CPU too hot aj AJ N BIOS timeout gt 5 Internal Board Error MEN Mikro Elektronik GmbH 52 20G020 00 E5 2014 01 21 amp Functional Description 2 15 2 Hot Swap LED After sys
10. 85 4 2 PCI Express Root Port Interrupt Mapping 85 JJ EEE E Pu qub ERES OI TE do NP E p 86 SJ Lithium Battery ooa daret emm rere pet aed pedes 86 6 Appendix 4 5 vesc e ES p CR ERE PUMP SUE PEE SEE RE MES 88 6 1 Literature and Web Resources 0 0 0 0 eee eene 88 6 1 CompactPCI Serial 2e bene rh br ER Rb Red 88 GS CPU GT tan DO iod 88 ol DU 88 O L4 USB user iio xdv Ome Sienna hd 88 6 15 Bthet et isse Uer RETE PIT bak de 88 Oo PD Adios Sorores oE ion Puy E RED NOR ra op 89 LT PCTEXPICSS anean ea e es e edda 89 6 2 Finding out the Product s Article Number Revision and Seal Numbers uu u9e Gane P ea pa oa tas eas mie oShs sape 89 MEN Mikro Elektronik GmbH 15 Figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 Map of the board front panel essor Rm Map of the board top view with CompactFlash board versions 02G020 00 and 01 lisse Map of the board top view with mSATA disk board versions 02G020 02 and 03 0 0 ee eee Map of the board top view with Ethernet rear I O card CompactPCI Serial backplane with filling order Position of battery on the CompactFlash adapter on the G20 board versions 00 and 301 s aec oe o inh godess dads Position of battery on the mSATA adapter on the G20 board versions 02 and 03 250 spa skr
11. DVMT 5 0 that the Internal Graphics Device will use Options 128 MB 256 MB MEN Mikro Elektronik GmbH 65 20G020 00 E5 2014 01 21 BIOS USB Configuration Sub menu Setup Warning Disabling USB devices or ports may cause your system to not enter setup and to prevent reenabling of USB devices or ports USB Legacy Enabled EC 3 Enabled EGIL 2 Enabled Pre Port Control Disabled USB RMH Mode Enabled USB Legacy Description If this menu item is enabled it is possible to boot from USB devices and use a USB keyboard under DOS Cannot be changed Options Enabled EHCI 1 2 Description Enable Disable EHCI 1 2 Options Enabled Disabled Pre Port Control Description Enable Disable the per port disable control override Options Enabled Disabled USB RMH Mode Description Enable Disable the PCH USB Rate Matching Hubs Mode Options Enabled Disabled MEN Mikro Elektronik GmbH 66 20G020 00 E5 2014 01 21 BIOS Chipset Configuration Setup warning Setting items on this screen to incorrect values may cause your system to malfunction PCI Latency Timer 32 VT d Enabled PCI Latency Timer Description Value to be programmed into PCI Latency Timer Register Options 32 64 96 128 160 192 224 248 VT d Description Check to enable VT d function on MCH Options Enabled Disabled MEN Mikro ElektronikGmbH rer 67 20G020 00 E5 2014 01 21 BIOS ACPI Table Feature Control FACP RIC S4 Wakeup Enabled
12. Description 2 Functional Description The following describes the individual functions of the board and their configuration on the board There is no detailed description of the individual controller chips and the CPU They can be obtained from the data sheets or data books of the semiconductor manufacturer concerned Chapter 6 1 Literature and Web Resources on page 88 2 1 Power Supply The G20 board is supplied with 12V only The voltage range is 9 V up to 16 V absolute maximum voltage The voltage is monitored within these borders The G20 board can optionally be supplied with 5V 5 3 standby voltage 2 2 Board Supervision The G20 provides an intelligent board management controller BMC with the following main features Board power sequencing control Voltage supervision System watchdog Software reset functionality Error state logging Power mode settings SMBus communication with main CPU The watchdog device monitors the board on operating system level If enabled the watchdog must be triggered by application software If the trigger is overdue the watchdog initiates a board reset and this way can put the system back into operation when the software hangs The watchdog uses a configurable time interval or is disabled Settings are made through BIOS or via an MEN software driver MEN provides a dedicated software driver for the board controller For a detailed description of the functionality of t
13. Disabled PCIE Break Event Description If Enabled PCI Express master activity will cause BM STS to be set and will cause a break from C3 C4 Options Enabled Disabled PCI Break Event Description If Enabled PCI master activity will cause BM STS to be set and will cause a break from C3 C4 Options Enabled Disabled EHCI Break Event Description If Enabled EHCI master activity will cause BM STS to be set and will cause a break from C3 C4 Options Enabled Disabled UHCI Break Event Description If Enabled UHCI master activity will cause BM STS to be set and will cause a break from C3 C4 Options Enabled Disabled HDA Break Event Description If Enabled Intel High Definition Audio master activity will cause BM STS to be set and will cause a break from C3 C4 Options Enabled Disabled MEN Mikro Elektronik GmbH 78 20G020 00 E5 2014 01 21 BIOS ACPI S3 Description Enable Disable ACPI S1 S3 Sleep state Options Enabled Disabled Wake on PME Description Determines the action taken when the system power is off and a PCI Power Management Enable wake up event occurs Options Enabled Disabled Auto Wake on S5 Description Auto wake on S5 By Day of Month or Fixed time of every day Options Disabled By every day By day of month MEN Mikro Elektronik GmbH 79 20G020 00 E5 2014 01 21 BIOS 3 5 Boot InsydeH20 Setup Utility Rev 3 5 Main Advanced Security Power Boot Exit UEFI Boot Enabled Quick Boot En
14. Ethernet on M12 connector instead of two interfaces on RJ45 Rear I O Ethernet Upto eight Gigabit Ethernet interfaces on the backplane using rear I O card e g GM1 Operating Temperature e 0 60 C Depends on board configuration CPU mezzanines hard disk Minimum 40 C all processors Cooling Concept Also available with conduction cooling in MEN CCA frame Please note that some of these options may only be available for large volumes Please ask our sales staff for more information For available standard configurations see online data sheet MEN Mikro Elektronik GmbH 8 20G020 00 E5 2014 01 21 Product Safety Product Safety A A Lithium Battery This board contains a lithium battery There is a danger of explosion if the battery is incorrectly replaced See Chapter 5 Maintenance on page 86 Electrostatic Discharge ESD Computer boards and components contain electrostatic sensitive devices Electrostatic discharge ESD can damage components To protect the board and other components against damage from static electricity you should follow some precautions whenever you work on your computer Power down and unplug your computer system when working on the inside Hold components by the edges and try not to touch the IC chips leads or cir cuitry Use a grounded wrist strap before handling computer components Place components on a grounded antistatic pad or on the bag that came with
15. LLL RHunctional Description Pin Assignment of Connector P5 Connector type of P5 72 pin Airmax VS 4 pair right angle header 6 rows 2 walls Table 14 Pin assignment of CompactPCI Serial P5 connector MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 E 3 7PE 7_PE_ 7_PE_ 6PE 6PE 6PE 5PE SPE SPE LK CLKE CLK CLK CLKEF CLK CLK CLKE CLK CLK CLKEF 4 PE 4PE 4PE 3PE 3PE 3PE 2PE 2PE 2PE tPE 1PE 1PE lt CLKEH CLK CLK CLKE CLK CLK CLKE CLK CLK CLKE CLK CLK PE SPE E SFE DM CU SPE MN EON 4 PE 8 PE 8 PE_ 8 PE_ SPE 8 PE_ 8PE 8PE GND EM Fikse gt Vo LEER VV LL 3 JE rE MENS PE eo PE Bu CF EE 2 Mee xb Mee 7_PE_ 7_PE_ 7_PE_ 7_PE_ ENS GE no T GND moo moo OND 7x00 Txo0 L K J l H G F E D C B A Note The signals written in gray are specified in the CompactPCI Serial specifica tion but not supported on this board Functional Description Table 15 Signal mnemonics of CompactPCI Serial rear connectors Signal Direction Function Compact PS ON out Power supply control signal PCI Serial PRST in Push button reset PWR_FAIL in Power supply fail RST out Reset signal SYSEN System slot identification connected to ground at the system slot PWRBTN
16. MEN Mikro Elektronik GmbH 26 20G020 00 E5 2014 01 21 Functional Description 2 7 Memory The standard board versions provide a memory configuration suitable for many applications However memory on the G20 can also be configured for your needs For standard memory sizes and ordering options please see MEN s website 2 7 1 DRAM System Memory The board provides 4 GB on board soldered DDR3 double data rate SDRAM The memory bus is 2x72 bits wide dual channel and operates with up to 1066 MHz 2 72 Boot Flash The G20 has an 64 Mbit SPI Serial Flash implemented as on board Flash for BIOS data 2 7 3 EEPROM The board has a 2 kbit serial EEPROM for factory data MEN Mikro Elektronik GmbH 27 20G020 00 E5 2014 01 21 Functional Description 2 8 Mass Storage The G20 offers the possibility to connect an mSATA disk CompactFlash on the older board versions 02G020 00 and 02G020 01 and a microSD card on a small adapter card in the heat sink area which is assembled by standard The slots are controlled via one USB port from the chipset 2 8 1 CompactFlash Board Versions 00 and 01 Even with CompactFlash the board needs only one slot in the system 2 8 1 1 Inserting and Extracting a CompactFlash Card The G20 supports standard CompactFlash cards For CompactFlash cards available from MEN see MEN S website The G20 is shipped without a CompactFlash card installed To install CompactFlash please stick to
17. OS Timer Watchdog Timer Description Fixed values that cannot be changed PCI Express Configuration PCI Express Clock Gating Enabled DMI Link ASPM Control LOsL1 PCEN Bpress Root Port I PCI Express Root Port 1 Enabled Automatic ASPM Auto URR Disabled FER Disabled NFER Disabled CER Disabled CTO Default SEFE Disabled SENFE Disabled SEGE Disabled PME Interrupt Disabled PIE SC I Disabled Hot Plug Disabled gt PCI Express Root Port gt PCI Express Root Port gt PCI Express Root Port gt PCI Express Root Port gt PCI Express Root Port gt PCI Express Root Port SPEIL Express Root Port PCI Express Clock Gating Description Options Enabled Disabled DMI Link ASPM Control Description Options LOsL1 Disabled LOs OO O OF WP MEN Mikro Elektronik GmbH 70 20G020 00 E5 2014 01 21 BIOS PCI Express Root Port 1 2 3 4 5 6 Description If PCI Express Root Port 1 is disabled PCI Express Root Ports 2 to 6 will also be disabled Options Enabled Disabled Automatic ASPM Description Automatically enables ASPM based on reported capabilities and known issues Options Disabled Auto LOs L1 LOsL1 URR Description Enable or disable PCI Express Unsupported Request Reporting Options Enabled Disabled FER Description Enable or disable PCI Express Device Fatal Error Reporting Options Enabled Disabled NFER Description Enable or disable Device Non Fatal Error Report
18. connectors at front panel Optionally two DVI HDMI ports via external adapter One DisplayPort at CPCI S 0 rear connector instead of one interface at the front Optionally SDVO or DVI HDMI port MEN Mikro Elektronik GmbH 4 20G020 00 E5 2014 01 21 Technical Data I O USB Two USB 2 0 host ports via Series A connector at front panel Eight USB 2 0 host ports via CPCI S 0 rear connector Two USB 2 0 host ports for connection of the rear I O card EHCI implementation Data rates up to 480 Mbit s Ethernet Two 10 100 1000Base T Ethernet channels at the front RJ45 connectors at front panel Ethernet controllers are connected by two x1 PCIeQ links Two onboard LEDs to signal LAN link activity status and connection speed SGPIO lines Accessible via CPCI S 0 rear connector Front Connections Two DisplayPort Two USB 2 0 Series A Two Ethernet RJ45 Rear I O 6SATA 1 DisplayPort 8 USB 5 PCI Express x1 links 2 PEG x8 links SGPIO PCI Express Two x8 PCI Express graphics links via CPCI S 0 rear connector e Five x1 PCIeQ links via CPCI S 0 rear connector Two x1 PCIeQ links to connect local 1000Base T Ethernet controllers e One x1 PCIeQG link via for connection of the rear I O card e PCIeQ 1 x support Data rate 250 MB s 2 5 Gbit s per lane Miscellaneous Real time clock with GoldCap backup battery buffered Power supervision and watchdog Temperature m
19. the following procedure M Power down your system and remove the G20 from the system M Put the board on a flat surface M Lift the CompactFlash holding bracket Heat Sink rs Aa M Insert the CompactFlash card carefully as indicated by the arrow on top of the card M Make sure that all the contacts are aligned properly and the card is firmly con nected with the card connector M Push the CompactFlash holding bracket back down until it clicks into place M Observe manufacturer notes on usage of CompactFlash cards MEN Mikro Elektronik GmbH 28 20G020 00 E5 2014 01 21 Functional Description 2 8 2 microSD Card The G20 provides an onboard microSD card slot on the bottom side of the mSATA adapter card in the heat sink area The slot is ready to use The G20 is shipped without a microSD card installed Please see MEN s website for ordering options do 2 8 2 1 Inserting and Extracting a microSD Card on the mSATA Adapter The microSD card has to be installed before the mS ATA disk as it is difficult to access it afterwards To install a microSD card please stick to the following procedure M Power down your system and remove the G20 from the system M Put the board on a flat surface M Insert the microSD card into the slot with the contacts at the top MI Make sure that it clicks into place properly M For extracting the card push it down and pull it out MEN Mikro Elektronik GmbH 29 20G020 00 E5
20. the publication Conditions for Use Field of Application The correct function of MEN products in mission critical and life critical applications is limited to the environmental specification given for each product in the technical user manual The correct function of MEN products under extended environmental conditions is limited to the individual requirement specification and subsequent validation documents for each product for the applicable use case and has to be agreed upon in writing by MEN and the customer Should the customer purchase or use MEN products for any unintended or unauthorized application the customer shall indemnify and hold MEN and its officers employees subsidiaries affiliates and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim or personal injury or death associated with such unintended or unauthorized use even if such claim alleges that MEN was negligent regarding the design or manufacture of the part In no case is MEN liable for the correct function of the technical installation where MEN products are a part of Trademarks All products or services mentioned in this publication are identified by the trademarks service marks or product names as designated by the companies which market those products The trademarks and registered trademarks are held by the companies producing them Inquiries concerning such trademarks
21. 20G020 00 E5 2014 01 21 G20 3U CompactPCI Serial Intel Core i7 CPU Board Men G20 3U CompactPCI Serial Intel Core i7 CPU Board G20 3U CompactPCl Serial Intel Core i7 CPU Board The G20 is a versatile 4HP 3U single board computer supporting a multitude of modern serial interfaces according to the CompactPCI Serial standard It is thus perfectly suited for data intensive applications which require high computing power The CPU card is equipped with Intel s Core i7 processor running at up to 3 2 GHz maximum turbo frequency and offering multi core architecture from Intel amp with full 64 bit support The G20 supports the Intel amp Active Management technology which makes it possible to access the board via the network even when it is in soft off or standby state The memory configuration of the G20 includes a state of the art fast DDR3 DRAM which is soldered to the board to guarantee optimum shock and vibration resistance An mSATA disk connected via a SATA channel and a microSD card device which is connected via a USB interface offer nearly unlimited space for user applications The board delivers an excellent graphics performance Two DisplayPort interfaces are accessible at the board front Using an external adapter two HDMI or two DVI ports can also be realized In addition the standard front I O comprises two PCIeQ driven Gigabit Ethernet and two USB 2 0 ports Serial interfaces at the rear I O
22. 3 CONFIGI 12 LANE 3 11 GND 10 LANE 3 9 LANE 2 8 GND 7 LANE 2 6 LANE 1 5 GND 4 LANE 1 3 LANE O 2 1 20 POWER 19 GND LANE 0 MEN Mikro Elektronik GmbH 34 20G020 00 E5 2014 01 21 Functional Description Table 4 Signal mnemonics of 20 pin DisplayPort connector Signal Direction Function GND Ground AUX AUX in out Bi directional half duplex auxiliary channels for device management and device control CONFIG1 CON Connected to Ground FIG2 HOTPLUG in Hot Plug Detect LANE 3 0 out Main Link data lanes LANE 3 0 POWER out Power for connector 3 3 V 500 mA RETURN PWR Return for Power 2 9 2 Rear I O The G20 provides a digital display interface on CompactPCI Serial connector P2 See Chapter 2 13 CompactPCI Serial on page 40 MEN Mikro Elektronik GmbH 35 20G020 00 E5 2014 01 21 Functional Description 2 10 USB Interfaces The G20 provides fourteen USB 2 0 ports controlled by the QM57 platform controller hub Two USB interfaces are routed to standard front panel connectors eight can be accessed on the CompactPCI Serial rear I O connectors and two are led to the board to board connector for the Ethernet rear I O adapter card e g GM1 The remaining two interfaces are used for connection of the mSATA disk CompactFlash on board versions 00 and 01 and the microSD card The USB interfaces support EHCI and UHCI 2 10 1 Front Pane
23. DRAM PEG x8 L va USB 2 0 EET 7 sam Ld 4 3 Gb es lt P gt USB 2 0 Cd retos DIEN GE 10 100 1000Base T USB 2 0 A Ethernet PCle x1 O S USB 2 0 Ooo TN 1000 se ko ER MENS TT COO NN USB 2 0 DisplayPort HDMI E 18820 P gt DisplayPort HDMI Controller Hub Connectors DisplayPort HDMI mSATA USB to SATA FPGA Board to Board EI USB 2 0 Connector USB 2 0 for Ethernet Rear I O Card PCle x1 SFF 8485 SGPIO MEN Mikro Elektronik GmbH 3 20G020 00 E5 2014 01 21 Technical Data Technical Data CPU Intel Core 17 610E 2 53 GHz processor core frequency 3 2 GHz maximum turbo frequency 1066 MHz system bus frequency Chipset QM57 Platform Controller Hub PCH Memory 4 MB L3 cache integrated in 17 processor Up to 4 GB SDRAM system memory Soldered DDR3 with ECC support Up to 1066 MHz memory bus frequency 64 Mbits boot Flash Serial EEPROM 2 KB for factory settings mSATA disk slot Connected via one USB to SATA bridge One microSD card slot Via USB Mass Storage Serial ATA SATA Six channels via rear I O SATA Revision 2 x support Transfer rates up to 300 MB s 3 Gbit s RAID level 0 1 5 10 support Hot plug together with G501 Graphics ntegrated in QM57 chipset 45nm Hi K process graphics 5 75th generation Maximum resolution 2560x1600 DisplayPort 1920x1200 HDMI DVI Two DisplayPort
24. Disabled A Port 1 HotPlug Disabled Spin Up Disabled A Port 2 HotPlug Disabled Spin Up Disabled A Por 3 k er Disabled Spin Up Disabled A Port 4 HotPlug Disabled Spin Up Disabled A Port 5 HotPlug Disabled Spin Up Disabled erial ATA Port 0 Not Installed erial ATA Port 1 Not Installed erial ATA Port 2 Not Installed erial ATA Port 3 Not Installed erial ATA Port 4 Not Installed erial ATA Port 5 Not Installed IDE Controller Description Enables or disables the IDE controllers Options Enabled Disabled HDC Configure as Description Set hard disk controller configure type Options IDE RAID AHCI AHCI RAID SALP Description Enable Disable AHCI RAID Support Aggressive Link Power Man agement SALP in AHCI Host Capability Register Bit 26 Options Enabled Disabled SGPIO Interface Description Switch for starting on or stopping off the SGPIO interface Options On Off SATA Port 0 1 2 3 4 5 Hot Plug Description Enable disable Hot Plug Options Enabled Disabled MEN Mikro Elektronik GmbH 6l 20G020 00 E5 2014 01 21 BIOS SATA Port 0 1 2 3 4 5 Spin Up Description On an edge detect from 0 to 1 the PCH starts a COMRESET ini tialization sequence to the device Options Enabled Disabled Serial ATA Port 0 1 2 3 4 5 Description Not installed You can make no changes here MEN Mikro Elektronik GmbH 62 20G020 00 E5 2014 01 21 BIOS Thermal Configuration Sub menu
25. IOD as rose nr esse E RUE ERU ERST UND RES OS 26 25 Reale lime Clock 4 42 were RUE Ya RR URECS UR 26 2 5 Processor COTG S Deo tque qub preti A BO ae sjabtya sjedee 26 2 6 1 Thermal Considerations osos eR reme 26 2 Memoari s avendo rt dons ah qe den eee ee dl eed gee one EA id 27 2 L1 DRAM System Memory 44 22 doen a oae era 27 2212 JBOOLB GSIY us eoh antag avn t ode eben ivo ba prese need 2 27 20 9 EPROM 5 piti piti rip ine ntes a EE EE 27 2 8 Mass Storage cec ew uoi d cand HER ERGO ede rene Ree bea 6 g 28 2 8 1 CompactFlash Board Versions 00 and 01 28 2 5 2 microSD Cards as scho PRU REGIS abet caves amon 29 283 uMSADADISES44 dex ORE DES T QUERER AT SG S 2 8 4 Serial ATA SATA 0 eee eens 33 29 Graphi Sessa saaeaneber save ina Gare beaa baade bade eee 34 2900 DEP POL iesopoke inibi teo engene 34 2 02 Rear VOsi rupier epe RR Re RI Rr 35 2 10 4S B INEA CES 5 omo porpadeptedrt adve pau eb seder demens ete 36 2 10 1 Front Panel Connection lsseleeee sess 36 2 10 2 Rear I O Connection CompactPCI Serial 36 2 10 3 Ethernet Rear I O Card Connection 36 2 11 Ethernet Interfaces uoce ot Re RIPE Aaa kue 37 2111 Front Panel Connection oio c LE IE Pre 37 2 11 2 Rear I O Connection CompactPCI Serial 38 2 12 PCT BXDI6SS 253b meh ken ok de eden Skeide 39 2 19 ASC ial oiu paused a eee ded 10833 9209 eRe S ACRIOR Hos 39 2 12 2 Implementat
26. M1 TM2 TM1 and TM2 ACPI 3 0 T States Description Enable or disable ACPI 3 0 T States Options Disabled Enabled Intelligent Power Sharing Description Intelligent Power Sharing configuration menu Note DTS must be enabled for Power Sharing to function Options Disabled Enabled CPU Turbo Description Enable or disable CPU Turbo Options Disabled Enabled MCH Turbo Description Enable or disable MCH Turbo Options Disabled Enabled MEN Mikro Elektronik GmbH 64 20G020 00 E5 2014 01 21 BIOS Video Configuration Sub menu PEG Force X1 Disabled Render Standby Enabled Render Thermal Throttling Enabled IGD Device2 Functionl Enabled IGD DVMT Pre Allocated 32MB IGD DVMT Total Gfx Mem 256MB PEG Force X1 Description When this option is enabled the PEG port is reduced to a x1 link Options Enabled Disabled Render Standby Description Check to enable render standby support Options Enabled Disabled Render Thermal Throttling Description This feature is applicable for Graphic SKUs only Options Enabled Disabled IGD Device2 Function1 Description Enable Disable function 1 of the internal graphics device by set ting item to the desired value IGD DVMT Pre Allocated Description Select DVMT5 0 Pre Allocated Fixed Graphics Memory size used by the Internal Graphics Device Options 32 MB 64 MB 128 MB 256 MB 96 MB 160 MB 224 MB 352 MB IGD DVMT Total Gfx Mem Description Select the size of
27. P 00 1 DDP 03 out Differential pairs of digital display interface 1 DDP 00 1 DDP 03 data lines DDP AUX DDP AUX in out Auxiliary channels for device management and device control DDPC HPD in Digital display interface hot plug detect 2 13 4 Ethernet Rear I O Card The eight Ethernet interfaces defined in the CompactPCI Serial standard on the P6 connector are not implemented directly on the G20 but on a special mezzanine board This way the number of Ethernet interfaces can be varied as required Two cards with 4 or 8 Ethernet interfaces are already available See MEN s website for ordering information The Ethernet rear I O card is connected to the G20 using a 40 pin connector leading two USB ports and one PCI Express interface to the card 2 13 4 1 Installing the Rear I O Card on the G20 The mounting material needed for the installation is included in the delivery of the adapter card It contains three screws for fixing the module and the gap pads required for thermally connecting the Ethernet controllers to the heat sink of the G20 Removing the mSATA Adapter Board For installing the rear I O card e g the GM1 on the G20 you have to remove the adapter board with the mSATA disk and the microSD card Carry out the following steps M Power down your system and remove the G20 from the system M Put the board on a flat surface MEN Mikro Elektronik GmbH 48 20G020 00 E5 2014 01 21 Functional Descr
28. abled Quiet Boot Enabled PXE Boot to LAN Disabled ACPI Selection ACPI 3 0 USB Boot Enabled Fast Boot Disabled gt EFI gt Legacy F1 Help N Select Item F5 F6 Change Values F9 Setup Defaults Esc Exit lt gt Select Menu Enter Select gt Sub F10 Save and Exit UEFI Boot Description Options Quick Boot Description Options Quiet Boot Description Options MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 menu Enable Disable UEFI Boot Function Enabled Disabled Allows InsydeH20 to skip certain tests while booting This will decrease the time needed to boot the system Enabled Disabled Disables or enables booting in Text Mode Enabled Disabled BIOS PXE Boot to LAN Description Disables or enables PXE boot to LAN Options Enabled Disabled ACPI Selection Description Select booting to Acpi3 0 Acpi1 0B Options Acpi3 0 Acpi1 0B USB Boot Description Disables or enables booting to USB boot devices Options Enabled Disabled Fast Boot Description Disables or enables Fast Boot function Options Enabled Disabled EFI Sub Menu EFI ACPI PNPOA03 0 Pci 1D10 Usb 0 0 Usb 1 0 HD Partl SigD808A4A4 EFI Boot Menu Description Selects the boot order for U EFI boot media In the example a USB memory device was detected as U EFI boot medium MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 BIOS Legacy Sub Menu Boot Device Priority gt Normal Boot Menu Normal Advance N
29. ae hoe de Sein Pha IRE dS Labels giving the product s article number revision and Serial number 23 2225 d06 dao doe eda Phas RU Sas ea E RETE Tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 Table 13 Table 14 Table 15 Table 16 Table 17 Table 18 Table 19 MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 Processor core options OD G20 50 5 95 25 0 8us dot m ane sen noi 26 DisplayPort adapters for the G20 sss sasessasae ser mehr deg oe 34 Pin assignment of 20 pin DisplayPort connector 34 Signal mnemonics of 20 pin DisplayPort connector 35 Pin assignment of USB front panel connectors 36 Signal mnemonics of USB front panel connectors 36 Signal mnemonics of Ethernet front panel connectors 2d Pin assignment and status LEDs of 8 pin RJ45 Ethernet front panel connectors LANT LAN2 4 err mr RRRPRE ARS E PEERS A 38 Pin assignment of 8 pin M12 Ethernet front panel connector 38 Pin assignment of CompactPCI Serial P1 connector 42 Pin assignment of CompactPCI Serial P2 connector 43 Pin assignment of CompactPCI Serial P3 connector 44 Pin assignment of CompactPCI Serial P4 connector 45 Pin assignment of CompactPCI Serial P5 connector 46 Signal mnemonics of CompactPCI Serial rear connectors
30. and IEC 61000 4 6 conducted disturbances BIOS e InsydeH2OTM UEFI Framework MEN Mikro Elektronik GmbH 6 20G020 00 E5 2014 01 21 Technical Data Intel Active Management Technology Out of Band OOB Access Power off Access Independent of OS status Power status control Keyboard Video Mouse KVM Viewer VNC compatible IDE Redirect Serial over LAN Manageability Engine in Chipset Network Filters in Chipset Dedicated Flash Storage Area Software Support Windows amp Linux tested verified with Ubuntu 10 04 kernel 2 6 32 21 32 bit and 64 bit ver sions OpenSuse 11 3 32 bit and 64 bit versions Detailed matrix of supported interfaces under Ubuntu 10 04 and OpenSuse 11 3 VxWorksQ on request QNX on request For more information on supported operating system versions and drivers see online data sheet i MEN Mikro Elektronik GmbH 7 20G020 00 E5 2014 01 21 Configuration Options Configuration Options CPU Intel Core i7 610E 2 53 GHz 4 MB Cache 35 W ntel amp CoreTM 17 620LE 2 GHz 4 MB Cache 25 W Intel Core 17 620UE 1 06 GHz 4 MB Cache 18 W Intel Core 15 520E 2 4 GHz 3 MB Cache 35 W no AMT support e Intel Core 13 330E 2 13 GHz 3 MB Cache 35 W no AMT support Memory System RAM 2GBor4 GB mSATA disk 0 MB up to maximum available microSD card 0 MB up to maximum available I O Ethernet One Gigabit
31. at Start Up Check always External PS Control Description Controls the external Power Supply Options Always on Switched Platform Reset Management Description Enables or blocks the RESET IN signal of the board Options RESET IN is RESET IN is blocked enabled MEN Mikro Elektronik GmbH 58 20G020 00 E5 2014 01 21 BIOS Spread Spectrum Control Description Enable or disable Spread Spectrum Options On Spread Spectrum enabled Off Spread Spectrum disabled MEN Mikro Elektronik GmbH 59 20G020 00 E5 2014 01 21 BIOS Peripheral Configuration Sub menu HD Audio Disabled LAN 1 Enabled Wake on LAN Enable Enabled LAN 2 Enabled HD Audio Description Enable or disable the HD Audio controller Options Disabled The controller is disabled even when there is an audio codec Enabled The controller is enabled independent of the presence of a codec LAN 1 LAN 2 Description Enables or disables the LAN interfaces Options Enabled Disabled Wake on LAN Enable Description Enable or disable integrated LAN to wake the system Options Enabled Disabled MEN Mikro Elektronik GmbH 60 20G020 00 E5 2014 01 21 BIOS IDE Configuration Sub menu ID HD AH SG SA SAT SAT SAT SAT SAT gt S gt S gt S gt S gt S gt S E Controller Enabled C Configure as AHCI CI RAID SALP Enabled PIO Interface 0n TA Port 0 HotPlug Disabled Spin Up
32. book www iol unh edu training ethernet html collection of links to Ethernet information including tutorials FAQs and guides ckp made it com ieee8023 html Connectivity Knowledge Platform at Made IT technology information service with lots of general information on Ethernet 6 1 6 HD Audio Intel High Definition Audio www intel com design chipsets hdaudio htm 6 1 7 PCI Express PCI Special Interest Group WWW pcisig com 6 2 Finding out the Product s Article Number Revision and Serial Number MEN user documentation may describe several different models and or design revisions of the G20 You can find information on the article number the design revision and the serial number on two labels attached to the board Article number Gives the product s family and model This is also MEN s ordering number To be complete it must have 9 characters Revision number Gives the design revision of the product Serial number Unique identification assigned during production If you need support you should communicate these numbers to MEN Figure 8 Labels giving the product s article number revision and serial number Complete article number 02G020 01 00 00 00 Ri 641517 Revision number Serial number MEN Mikro Elektronik GmbH 89 20G020 00 E5 2014 01 21
33. connectors are 8 USB 6 SATA interfaces one DisplayPort or HDMI instead of one interface at the front panel 5 PCI Express x1 links and two PEG x8 links Up to eight Gigabit Ethernet interfaces can be realized using a rear I O adapter board Thermal supervision of the processor and a watchdog for the operating system complete the functionality of the G20 The G20 operates in Windows and Linux environments as well as under real time operating systems that support Intel amp s multi core architecture The InsydeH20TM EFI BIOS was specially designed for embedded system applications The G20 is suited for a wide range of industrial applications e g for monitoring vision and control systems as well as test and measurement Main target markets comprise industrial automation multimedia traffic and transportation aerospace shipbuilding medical engineering and robotics The G20 comes with a tailored passive heat sink within 4 HP height The robust design of the G20 makes the board especially suited for use in rugged environments with regard to shock and vibration according to applicable DIN EN or IEC industry standards The G20 is also ready for coating so that it can be used in humid and dusty environments and has a guaranteed minimum standard availability of 7 years MEN Mikro Elektronik GmbH 2 20G020 00 E5 2014 01 21 Diagram Diagram Front panel connector Rear I O connector H Options DDR3 SDRAM EE ECC DDR3 S
34. disable Intel AMT Setup Prompt to wait for hot key to enter setup Options Enabled Disabled Intel AMT SPI Protected Description Enable or disable Intel AMT SPI write protect Options Enabled Disabled Intel AMT Password Write Description Enable Intel AMT Password Write Password is writeable when Enable is set Options Enabled Disabled HECI Timeout Description Enable or disable HECI Timeout for send read message and wait for initialization Options Auto Manual AMT Wait Timer Description Set timer to wait before sending ASF GET BOOT OPTIONS Options 1 Unconfigure ME Description Unconfigure ME without password Options Enabled Disabled Verbose Mebx Output Description Enable or disable Verbose Mebx Output Options Enabled Disabled USB Configure Description Enable or disable USB Configure function Options Enabled Disabled PET Progress Description User can enable or disable PET events progress to receive PET events or not Options Enabled Disabled Me Local FW Update Enable Description Enable or disable Me Local FW Update Enable function Options Enabled Disabled MEN Mikro Elektronik GmbH 69 20G020 00 E5 2014 01 21 BIOS Me Local FW Qualifier Description Set Me Local FW Qualifier to Options Always Never Restricted ASF Support Description Enable or disable Alert Specification Format Options Enabled Disabled Watchdog Support Description Enable or disable Watchdog timer Options Enabled Disabled
35. ducts 08GM02 html 6 1 1 CompactPCI Serial CompactPCI Serial Specification PICMG CPCI S 0 Revision 1 0 2011 PCI Industrial Computers Manufacturers Group PICMG www picmg org e Introduction to CompactPCI Serial on Wikipedia en wikipedia org wiki CompactPCI Serial 6 1 2 CPU ntel Embedded Processors developer intel com products embedded processors htm 6 1 3 SATA Serial ATA International Organization SATA IO www serialata org 6 1 4 USB USB Universal Serial Bus Specification Revision 1 0 1996 Compaq Digital Equip ment Corporation IBM PC Company Intel Microsoft NEC Northern Telecom www usb org 6 1 5 Ethernet Ethernet in general The Ethernet A Local Area Network Data Link Layer and Physical Layer Specifications Version 2 0 1982 Digital Equipment Corpora tion Intel Corp Xerox Corp ANSIU IEEE 802 3 1996 Information Technology Telecommunications and Information Exchange between Systems Local and Metropolitan Area Networks Specific Requirements Part 3 Carrier Sense Multiple Access with Collision Detection CSMA CD Access Method and Phys ical Layer Specifications 1996 IEEE www ieee org MEN Mikro Elektronik GmbH 88 20G020 00 E5 2014 01 21 Appendix www ethermanage com ethernet links to documents describing Ethernet components media the Auto Negotia tion system multi segment configuration guidelines and information on the Ethernet Configuration Guidelines
36. e on PME Disabled Auto Wake on S5 Disabled f Select Item lt gt Select Menu F1 Help Esc Exit BIOS Rev 3 5 Boot Exit F5 F6 Change Values Enter Select Sub menu F9 Setup Defaults F10 Save and Exit Advanced CPU Control Sub Menu TXT P States IST Boot Performance Mode CMP Support HT Support Use XD Capability VT Support C States Enhanced C States Enable C6 Interrupt Filtering Turbo Mode MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 ips Treni fon C2 mmm ET Disable Enabled Max Performance Auto Auto Enabled Disabled bled bled bled abled c 0 o BIOS TXT Description Enables utilization of additional hardware capabilities provided by Intel Trusted Execution Technology changes require a full power cycle to take effect Options Enabled Disabled P States IST Description Enable processor performance states P States Options Enabled Disabled Boot Performance Mode Description Select the performance state that BIOS will set before OS hand off Options Max Performance Max Battery CMP Support Description Enable or disable core multi processing Options Auto Disabled HT Support Description Enable or disable Hyper Threading Options Auto Disabled Use XD Capability Description Enable or disable XD capability Options Enabled Disabled VT Support Description Enable or disable Vanderpool technolo
37. easurement 2 board status LEDs 2user LEDs Reset button MEN Mikro Elektronik GmbH o 20G020 00 E5 2014 01 21 Technical Data CompactPCI Serial Compliance with CompactPCI Serial PICMG CPCI S 0 Specification System slot Electrical Specifications Supply voltage power consumption 12V 9 16V 45W 5V 5 5 standby voltage optional Mechanical Specifications Dimensions conforming to CompactPCI Serial specification for 3U boards Front panel 4HP with ejector Weight 208 g w o heat sink 398 g with heat sink and mSATA adapter Environmental Specifications Temperature range operation 0 460 C Airflow min 1 5 m s typical power dissipation 29W with Windows XP operating system 1 Gb Ethernet without CPU clock reduction Temperature range storage 40 85 C Relative humidity operation max 9596 non condensing Relative humidity storage max 9596 non condensing Altitude 300 m to 3 000 m Shock 50 m s 30 ms Vibration function 1 m s 5 Hz 150 Hz Vibration lifetime 7 9 m s 5 Hz 150 Hz Conformal coating on request MTBF 435 685h 40 C according to IEC TR 62380 RDF 2000 Safety PCB manufactured with a flammability rating of 94V 0 by UL recognized manu facturers EMC Conforming to EN 55022 radio disturbance IEC 61000 4 2 ESD IEC 61000 4 3 electromagnetic field immunity IEC 61000 4 4 burst IEC 61000 4 5 surge
38. em slot The interfaces are accessible at the following slots see Figure 5 CompactPCI Serial backplane with filling order on page 41 One SATA interface on slot 4 5 6 7 8 and 9 each One USB interface on slot 2 3 4 5 6 7 8 and 9 each One PCI Express x8 link on slot 2 and 3 each One PCI Express x1 link on slot 4 5 6 7 and 8 each Please see the CompactPCI Serial specification PICMG CPCI S 0 for more information MEN Mikro Elektronik GmbH 41 20G020 00 E5 2014 01 21 2 13 3 Pin Assignment of Connector P1 Connector type of P1 Functional Description CompactPCI Serial Connectors P1 P5 72 pin Airmax VS 4 pair right angle header 6 rows 4 walls Table 10 Pin assignment of CompactPCI Serial P1 connector 22200282202 ICPE i AORE 1 PE ape 1EPE SESS A PE EPER Rx03 Rx03 cnp Tx03 Tx03 END Rx02 Rx02 GND Tx02 Tx02 END 2 1PE 1PE Sp eRe Wess MERE 1_PE Sp END Rx01 Rx01 QD Tx01 Tx01 END Rx00 Rx00 END TX00 Tx00 8 SA SA 1 SA SA TA R TA Rx GND TA T TA Tx GND reserved reserved 4 SATA_ SATA_ SATA SATA PWR GAS sL sce OU sbo spi FAIL 3 GND WAKE IPMB_ IPMB SYS reserved GND PRST GND RST PS_ON GND P GND 2 IN SDA SCL EN STND GND 12V 12V GND 12V 12V GND 12V 12V GND BY 12V 1 L K J H G F E D C B A Note The signals written in gray are specified in the CompactPCI Serial
39. facturers and to optimize the usability in CompactPCI Serial systems the order to implement the interfaces is defined PCI Express USB and Ethernet are ascending SATA SAS is descending This means that the first PCI Express link and the first USB and Ethernet ports from the system slot are led to the first peripheral slot the second to the second etc and the first SATA interface to the eighth peripheral slot the second to the seventh etc See Figure 5 CompactPCI Serial backplane with filling order on page 41 MEN Mikro Elektronik GmbH 40 20G020 00 E5 2014 01 21 Functional Description Figure 5 CompactPCI Serial backplane with filling order Fat Pipe Fat Pipe System Perip Perip Perip Perip Perip Perip Perip Perip Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 6 Slot 7 Slot 8 Slot 9 D D bi bi g bi 8 0 B D 0 if il i E E i M 1 T bi 0 0 B 0 if if i if d h CE Hg HB NR h PCI Express 1 2 3 4 5 6 7 8 USB 1 2 3 4 5 6 7 8 Ethernet 1 2 3 4 5 6 7 8 SATA 8 7 6 5 4 3 2 1 2 13 2 Implementation on the G20 The G20 supports 6 SATA interfaces 8 USB 2 0 1 DisplayPort five PCI Express x1 links as well as two PEG x8 PCI Express fat pipe ports on the backplane Please note that slot 9 does not support PCI Express and slots 2 and 3 do not support SATA on a standard 9 slot CompactPCI Serial backplane with the G20 in the syst
40. gy Options Enabled Disabled C States Description Enable processor idle power saving states C States Options Enabled Disabled Enhanced C States Description Enable P State transitions to occur in combination with C States Options Enabled Disabled Enable C6 Description Enables or disables the C6 state Deep Power Down Technol ogy Options Enabled Disabled MEN Mikro Elektronik GmbH 76 20G020 00 E5 2014 01 21 BIOS Interrupt Filtering Description When enabled only the core that is the destination of an interrupt while in C3 C6 will be notified to transition to CO When disabled all cores that are in C3 C6 will be notified to transition to CO regardless of interrupt destination Options Enabled Disabled Turbo Mode Description Enable processor Turbo Mode requires EMTTM enabled too Options Enabled Disabled MEN Mikro Elektronik GmbH 77 20G020 00 E5 2014 01 21 BIOS Platform Power Management Sub Menu PCI Clock Run Enabled PCI Clock Run Description If Enabled the CLKRUN Logic will stop the PCI Clocks Options Enabled Disabled Break Event Sub Menu Storage Break Event Disabled PCIE Break Event Disabled PCI Break Event Disabled EHCI Break Event Disabled UHCI Break Event Disabled HDA Break Event Disabled Storage Break Event Description If Enabled Parallel IDE or Serial ATA master activity will cause BM STS to be set and will cause a break from C3 C4 Options Enabled
41. he CompactPCI Serial connectors See Chapter 2 13 3 CompactPCI Serial Connectors P1 P5 on page 42 for a detailed description of the CompactPCI Serial connectors MEN Mikro Elektronik GmbH 39 20G020 00 E5 2014 01 21 Functional Description 2 13 CompactPCI Serial 2 13 1 General CompactPCI Serial is an independent basic standard designated PICMG CPCI S 0 This standard introduces a completely new connector which enables a high signal density and supports transmission frequencies of 12 Gb s and more CompactPCI Serial is based on the mechanics of CompactPCI so it remains compatible to IEC 1101 but it only supports modern point to point connections This compatibility allows to use all standard 19 system solutions because the dimensions of the backplanes are identical and are fixed in the same way The front panels handles and the well proven hot plug mechanics the switch in the handle also remain the same Only the connector is replaced by a modern type which is able to support the high frequencies The CompactPCI Serial architecture a simple star combined with a complete mesh for Ethernet functions without switches and bridges There is a system slot and up to eight peripheral slots with congruent pin assignments The CompactPCI Serial standard supports a maximum of 2 PCI Express x8 links fat pipe 6 PCI Express x4 8 SATA 8 USB and 8 Ethernet interfaces To guarantee maximum compatibility between different board manu
42. he driver software please refer to the drivers documentation You can find any driver software and documentation available for download on MEN s website MEN Mikro Elektronik GmbH 24 20G020 00 E5 2014 01 21 do Functional Description 2 3 Intel Active Management Technology AMT G20 boards equipped with an Intel Core i7 processor support Intel Active Management Technology AMT Intel AMT is powered by a separate hardware engine in Intel chipsets which enables e g out of band OOB diagnostics remote control IDE Redirect Serial over LAN SOL agent presence checking and network traffic filtering AMT is supported on the lower front Ethernet interface ETH2 of the G20 For information on how to enable the AMT BIOS extension see Chapter 3 BIOS MEN provides an application note on how to switch on the AMT functionality and log onto the CPU board via VNC afterwards See MEN s website If the supercapacitor and or the battery is empty the G20 loses its complete AMT settings due to Intel s security standards MEN Mikro Elektronik GmbH 25 20G020 00 E5 2014 01 21 Functional Description 2 4 Reset Behavior The G20 can be reset using the reset button on the front panel or the PRST signal on the backplane See also Chapter 2 14 Reset Button on page 52 2 5 Real Time Clock The board includes a real time clock connected to the chipset For data retention during power off the RTC is backed up by a supe
43. ht O 2014 MEN Mikro Elektronik GmbH All rights reserved Germany France USA MEN Mikro Elektronik GmbH MEN Mikro Elektronik SA MEN Micro Inc Neuwieder Strafe 3 7 18 rue Ren Cassin 860 Penllyn Blue Bell Pike 90411 Nuremberg ZA de la Ch telaine Blue Bell PA 19422 Phone 49 911 99 33 5 0 74240 Gaillard Phone 215 542 9575 Fax 49 911 99 33 5 901 Phone 33 0 450 955 312 Fax 215 542 9577 E mail info men de Fax 33 0 450 955 211 E mail sales O menmicro com www men de E mail info men france fr www menmicro com www men france fr MEN Mikro Elektronik GmbH 13 20G020 00 E5 2014 01 21 Contents Contents L Getting Started 5csosos ote y o e re oe eie m Re ae e ke Sa 18 LI Map Or the Boatd 53 ssa asco did ed Hg apud to p pneu 18 1 2 Configuring the Hardware asses eb hme 21 1 3 Integrating the Board into a System 00 22 1 4 Troubleshooting at Start up 0 0 2 eee 23 15 Contignring BIOS 24 hrbrs s boss Skies eae 23 1 6 Installing Operating System Software 0 0000005 23 1 6 1 Installing Windows XP or Windows 7 on USB Devices 23 17 Installing Driver SolbWale cu doro sd deron dero toe td 23 2 Functional Description s one e REC ME E nPSEREFRRE EEG UPS T ER 24 2 Power SUPPLY si oai ewe erri binse diet iodine eae taunts 24 2 2 Board SUDSEVISIOIsg d jaws teas asd gu te tug dud pde etu 24 2 3 Intel Active Management Technology AMT 25 2 4 Reset BeBav
44. ing Options Enabled Disabled CER Description Enable or disable PCI Express Device Correctable Error Report ing Options Enabled Disabled CTO Description Set PCI Express Completion Timer Options Default Disabled 16 55 ms 65 210 ms 260 900 ms 1 3 5 ms SEFE Description Enable or disable Root PCI Express System Error on Fatal Error Options Enabled Disabled SENFE Description Enable or disable Root PCI Express System Error on Non Fatal Error Options Enabled Disabled MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 BIOS SECE Description Enable or disable Root PCI Express System Error on Correctable Error Options Enabled Disabled PME Interrupt Description Enable or disable Root PCI Express PME Interrupt Options Enabled Disabled PME SCI Description Enable or disable PCI Express Hot Plug SCI Options Enabled Disabled Hot Plug Description Enable or disable PCI Express Hot Plug Options Enabled Disabled MEN Mikro Elektronik GmbH 72 20G020 00 E5 2014 01 21 BIOS 3 3 Security InsydeH20 Setup Utility Rev 3 5 Main Advanced Security Power Boot Exit TPM Status Not Installed Supervisor Password Installed Not Installed User Password Installed Not Installed Set Supervisor Password Power on password Disabled User Access level View Only Set User Password Clear User Password F1 Help N Select Item F5 F6 Change Values F9 Setup Defaults Esc Exit lt gt Select Menu Enter Select gt Sub
45. ion on G20 0 eee eee eee eee 39 2 15 CompactPCl Serial 5 php salver EID shad 40 213 4 General uu uc ee dod ares e e e tene e peindre 40 MEN Mikro Elektronik GmbH 14 20G020 00 E5 2014 01 21 20G020 00 E5 2014 01 21 Contents 2 13 2 Implementation on the G20 2 cse ne 41 2 13 3 CompactPCI Serial Connectors P1 P5 42 2 134 Ethernet Rear VO Card oa sd denm eats 48 2 14 Reset BUON erete en PIT he ndund the nde ha edialet ce peeled ap penas 52 2 15 Status LEDS s reser bredt resp p eaters es DEN EEE aes 52 2 15 1 Status LED sac cas rb eR beer ena ses 52 2 15 2 Hot Swap LED iot i prenit PU water peePPPeI we 53 2 155 User TES sanere n Suid np Rude qan bau a 23 3 BIOS qus ex 99 ECRREC ORE FOER RETO CRY EF REEREEKRT OR EE UT ee 54 Sul N S s ui poised tubo teo P ignita dunt basen eee 55 32 Advanced ok hs c e RE Re ee REFER NEMPE 57 5E ces P EE PTE EN DTE 13 Dur Pb 75 JET TEN EE RS 80 20 Fie 83 3 6 1 Exit Saving Changes odes cea Rh 83 3 02 Save Change Without EXit lt 3063 24 saticis snieg satus 83 3 63 Exit Discarding Changes 245 naa iere OR seanse 83 3 6 4 Load Optimal Defaults 1 3251 nee 83 365 Load Custom Defaults 5 532 200 doen odes bake es 84 3 6 6 Save Custom Detaults sica e RR hm ete 84 B00 Discard Cages cio cage ce eran PERCHE erte 84 4 Organization of the Board eeeeeeeeee eere nnn 85 41 SMBUS DEVICES oi cob er TePUrCEPRPO PPM Ye td et auetardrs
46. iption M Loosen and remove the screws highlighted in red fastening the mSATA adapter to the G20 M Remove the adapter taking care not to damage the pins of the board to board connector Installing the GM1 on the G20 M Take the gap pad from the mounting material delivered with the rear I O card and remove the plastic film from one side of the gap pads Mi Press the gap pad onto the Ethernet controller of the GM1 highlighted in red M Remove the plastic film on the other side M Align the board to board connectors of the G20 and the rear I O card and push the card down carefully MEN Mikro Elektronik GmbH 49 20G020 00 E5 2014 01 21 Functional Description M Fasten the rear I O card using the three screws included in the delivery of the card MEN Mikro Elektronik GmbH 50 20G020 00 E5 2014 01 21 Functional Description Installing the GM2 on the G20 M Take the gap pads from the mounting material delivered with the rear I O card and remove the plastic film from one side of the gap pads MI Press the gap pads onto the Ethernet controllers of the GM2 highlighted in red Yoo EN b q M Remove the plastic film on the other side of the pads M Align the board to board connectors of the G20 and the rear I O card and push the card down carefully M Fasten the rear I O card using the three screws included in the delivery of the card MEN Mikro Elektronik GmbH 51 20G020
47. ktronik GmbH 85 20G020 00 E5 2014 01 21 Maintenance 5 Maintenance 5 1 Lithium Battery The board contains a lithium battery There is a danger of explosion if the battery is incorrectly replaced Replace only with the same or equivalent type Manufacturer Renata Type CR2032 Capacity 235 mAh The battery has to be UL listed Used batteries have to be disposed of according to the local regulations concerning the disposal of hazardous waste Figure 6 Position of battery on the CompactFlash adapter on the G20 board versions 00 and 01 CompactFlash Display Port Connectors USB Connectors Heat Sink Ethernet Connectors Battery M12 Connector for Ethernet optional MicroSD MEN Mikro Elektronik GmbH 86 20G020 00 E5 2014 01 21 Maintenance Figure 7 Position of battery on the mSATA adapter on the G20 board versions 02 and 03 mSATA microSD bottom Display Port Connectors USB Connectors Heat Sink Ethernet d Connectors i M12 Connector for Ethernet optional MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 Appendix 6 Appendix c 6 1 Literature and Web Resources G20 data sheet with up to date information and documentation www men de products 02G020 html e GMI data sheet with up to date information and documentation www men de products 08GM01 html e GM2 data sheet with up to date information and documentation www men de pro
48. l Connection Two USB interfaces are accessible at the front panel Connector types 4 pin USB Series A receptacle according to Universal Serial Bus Specification Revision 1 0 Mating connector 4 pin USB Series A plug according to Universal Serial Bus Specification Revi sion 1 0 Table 5 Pin assignment of USB front panel connectors 1 5V 2 USB D 3 USB D 4 GND Table 6 Signal mnemonics of USB front panel connectors Signal Direction Function 5V out 5 V power supply GND Digital ground USB D USB D in out USB lines differential pair 2 10 2 Rear I O Connection CompactPCI Serial Eight USB interfaces are accessible via rear I O in compliance to the CompactPCI Serial standard PICMG CPCI S 0 See Chapter 2 13 CompactPCI Serial on page 40 for rear I O pin assignments 2 10 3 Ethernet Rear I O Card Connection Two USB interfaces are led to the Ethernet rear I O adapter card which is used to realize Ethernet via rear I O and a microSD card interface See Chapter 2 13 4 Ethernet Rear I O Card on page 48 for details on the mezzanine interface MEN Mikro Elektronik GmbH 36 20G020 00 E5 2014 01 21 Functional Description 2 11 Ethernet Interfaces The G20 has two Ethernet interfaces connected to the platform controller hub via two x1 PCI Express PCIe links They are controlled by an Intel 82574L Ethernet controller and an 82577LM Ethernet Controller PHY They suppo
49. llation MEN Mikro Elektronik GmbH 10 20G020 00 E5 2014 01 21 About this Document Conventions This sign marks important notes or warnings concerning proper functionality of the product described in this document You should read them in any case italics Folder file and function names are printed in italics bold Bold type is used for emphasis monospace A monospaced font type is used for hexadecimal numbers listings C function descriptions or wherever appropriate Hexadecimal numbers are preceded by Ox comment Comments embedded into coding examples are shown in green color hyperlink Hyperlinks are printed in blue color The globe will show you where hyperlinks lead directly to the Internet so you can look for the latest information online IRQ Signal names followed by or preceded by a slash indicate that this signal is IRQ either active low or that it becomes active at a falling edge in out Signal directions in signal mnemonics tables generally refer to the corresponding board or component in meaning to the board or component out meaning coming from it Vertical lines on the outer margin signal technical changes to the previous issue of the document MEN Mikro Elektronik GmbH Il 20G020 00 E5 2014 01 21 About this Document Legal Information Changes MEN Mikro Elektronik GmbH MEN reserves the right to make changes without further notice to any products herein Warra
50. ls on the G20 s BIOS in Chapter 3 BIOS on page 54 1 6 Installing Operating System Software The board supports Windows Linux VxWorks on request and QNX on request By standard no operating system is installed on the board Please refer to the respective manufacturers documentation on how to install operating system software You can find any software available on MEN s website 1 6 1 Installing Windows XP or Windows 7 on USB Devices The CompactFlash on board versions 00 and 01 and the microSD card of the G20 is connected via USB A standard Windows operating system like Windows XP Professional or Windows 7 Ultimate does not support direct installation on USB memory devices There are three possible solutions Install the operating system on the mSATA disk of the G20 on board versions 02 and 03 Add a hard drive SATA mSATA on a peripheral board or side card Switch to an Embedded Windows like Windows Embedded Standard or Win dows Embedded Standard 7 These Embedded Windows operating systems sup port being installed on and booted from a USB device Linux supports booting from a USB device without problems 1 7 Installing Driver Software For a detailed description on how to install driver software please refer to the respective documentation You can find any driver software and documentation available for download on MEN s website MEN Mikro Elektronik GmbH 23 20G020 00 E5 2014 01 21 Functional
51. nty Guarantee Liability MEN makes no warranty representation or guarantee of any kind regarding the suitability of its products for any particular purpose nor does MEN assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability including without limitation consequential or incidental damages TO THE EXTENT APPLICABLE SPECIFICALLY EXCLUDED ARE ANY IMPLIED WARRANTIES ARISING BY OPERATION OF LAW CUSTOM OR USAGE INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE OR USE In no event shall MEN be liable for more than the contract price for the products in question If buyer does not notify MEN in writing within the foregoing warranty period MEN shall have no liability or obligation to buyer hereunder The publication is provided on the terms and understanding that 1 MEN is not responsible for the results of any actions taken on the basis of information in the publication nor for any error in or omission from the publication and 2 MEN is not engaged in rendering technical or other advice or services MEN expressly disclaims all and any liability and responsibility to any person whether a reader of the publication or not in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance whether wholly or partially on the whole or any part of the contents of
52. ooting an operating system and running pre boot applications This product line is the next generation of PC BIOS technology The gt character in front of a menu item means that a sub menu is available An x in front of a menu item means that there is a configuration option which needs to be activated through a higher configuration option before being accessible MEN Mikro Elektronik GmbH 54 20G020 00 E5 2014 01 21 BIOS 3 1 Main InsydeH20 Setup Utility Rev 3 5 Main Advanced Security Power Boot Exit InsydeH20 Version Axxx BIOS V 1 xx Processor Type Intel Core i7 610E 2 53GHz System Bus Speed 1066 MHz System Memory Speed 1067 MHz Cache RAM 1024kB Total Memory 4096MB Intel ME Version 6 1 10 1052 MEN EC Version PIC 1 3 1 2 SODIMM 0 2048MB SODIMM 1 1024MB Language English System Time hh mm ss System Date mm dd yyyy F1 Help N Select Item F5 F6 Change Values F9 Setup Defaults Esc Exit lt gt Select Menu Enter Select Sub F10 Save and Exit menu InsydeH20 Version MEN Board Processor Type System Bus Speed System Memory Speed Cache RAM Total Memory Intel ME Version MEN EC Version SODIMM 0 SODIMM 1 Description You cannot change any values in these fields They are only for information Language Description Select the default language Options English MEN Mikro Elektronik GmbH 55 20G020 00 E5 2014 01 21 System Time BIOS Description Change the internal clock Options Sys
53. ormal Advance gt Boot Type Order KingstonDataTraveler G3 Floppy Drive Hard Disk Drive CD DVD ROM Drive USB Others gt USB KingstonDataTraveler G3 Normal Boot Menu Description Selects the type of boot order Options Normal Sub menu Boot Type Order Under this menu option it is possible to select the boot order of device groups e g Hard Disk before Floppy Drive Sub menu USB Under this menu option it is possible to select the boot order of single devices within a device group e g USB HDD before SATA HDD Advance Under this menu option there are no device groups The single devices are listed and can be moved to select the boot order e g SATA HDD1 USB Floppy USB DVD DRIVE SATA HDD2 MEN Mikro Elektronik GmbH 82 20G020 00 E5 2014 01 21 3 6 Exit InsydeH20 Setup Utility Main Advanced Security Power Boot Exit Exit Saving Changes Save Change Without Exit Exit Discarding Changes Load Optimal Defaults Load Custom Defaults Save Custom Defaults Discard Changes F1 Help N Select Item F5 F6 Change Values Esc Exit gt Select Menu Enter Select Sub menu 3 6 1 Exit Saving Changes Exit system setup and save your changes 3 6 2 Save Change Without Exit Save your changes without exiting the system 3 6 3 Exit Discarding Changes Exit system setup without saving your changes 3 6 4 Load Optimal Defaults If this option is selected a verified factory setup is loaded BIOS Rev 3 5
54. platform controller hub and provides six SATA channels In compliance with the CompactPCI Serial standard these interfaces are led to CompactPCI Serial rear I O connector P3 The interface is compliant to the SATA generation 2 3 0 Gb s specification and can be run in AHCI and RAID mode See Chapter 2 13 CompactPCI Serial on page 40 for the rear I O pin assignment MEN Mikro Elektronik GmbH 33 20G020 00 E5 2014 01 21 Functional Description 2 9 Graphics The graphics subsystem is part of the CPU and supports the following features 45nm Hi K process graphics e 5 75th generation Maximum resolution 2560x1600 DisplayPort 1920x1200 HDMI DVI 2 9 1 Display Port Two DisplayPort interfaces can be accessed at the front panel Using adapters two DVI or two HDMI interfaces are also possible MEN offers a DisplayPort to DVI D Adapter as an accessory See MEN s website for ordering information In the following table you can find a list of adapters that have also been tested and can be used with the G20 Table 2 DisplayPort adapters for the G20 Manufacturer Ordering Number ACTEBIS 1444334 ROHS CONRAD 971726 62 ROHS HP FH973AT ROHS JJ COMPUTER AVC 123 0 2M ROHS Connector types 20 pin DisplayPort receptacle Mating connector 20 pin DisplayPort plug Table 3 Pin assignment of 20 pin DisplayPort connector RETURN PWR 18 HOTPLUG 17 AUX 16 GND 15 AUX 14 CONFIG2 1
55. rcapacitor The supercapacitor gives an autonomy of approx 14 hours when fully loaded The RTC can generate interrupt requests to the chipset The RTC has an accuracy of approximately 1 7 seconds day 11 minutes year at 25 C For retention of time date data after a power off of more than 8 10 hours the RTC is also backed by a battery Note The battery is not available if you use an Ethernet rear I O card e g GM1 on the G20 For ordering options please see MEN s website 2 6 The G20 can be equipped with different types of Intel Core 17 15 or 13 processors The following table gives a performance overview Processor Core Table 1 Processor core options on G20 AN Processor Type Core Frequency Power Class L2 Cache AMT Support Intel Core i7 610E 2 58 GHz 35W 4 MB yes Intel Core i7 620LE 2 GHz 25W 4 MB yes Intel Core i7 620UE 1 06 GHz 18W 4 MB yes Intel Core i5 520E 2 4 GHz 35W 3 MB no Intel Core i3 330E 2 13 GHz 35 W 3 MB no 2 6 1 Thermal Considerations A suitable heat sink is provided to meet thermal requirements For special requirements a larger heat sink is also available on request Please contact MEN sales for more information Please note that if you use any other heat sink than that supplied by MEN or no heat sink at all warranty on functionality and reliability of the G20 may cease If you have any questions or problems regarding thermal behavior please contact MEN
56. rt 10 Mbits s up to 1000 Mbits s as well as full duplex operation and autonegotiation The unique MAC address is set at the factory and should not be changed Any attempt to change this address may create node or bus contention and thereby render the board inoperable The MAC addresses on G20 are LANI Ox 00 CO 3A 05 8x xx 0x 00 CO 3A 05 Bx xx LAN2 Ox 00 CO 3A 05 Cx xx Ox 00 CO 3A 05 Fx xx where 00 CO 3A is the MEN vendor code 05 is the MEN product code The last four digits depend on the interface and the serial number of the product The serial number is added to the offset for example for LANI Serial number 0042 Ox xx xx 0x8000 0x002A Ox 80 2A See Chapter 6 2 Finding out the Product s Article Number Revision and Serial Number on page 89 2 11 1 Front Panel Connection Two standard RJ45 connectors are available at the front panel There are two status LEDs for each channel at the front panel The pin assignment corresponds to the Ethernet specification IEEE802 3 Table 7 Signal mnemonics of Ethernet front panel connectors Signal Direction Function BI Dx in out Differential pairs of data lines for 1000Base T RX in Differential pair of receive data lines for 10 100Base T TX out Differential pair of transmit data lines for 10 100Base T MEN Mikro Elektronik GmbH 37 20G020 00 E5 2014 01 21 Functional Description Connection via RJ45 Connectors Connector type
57. s Modular 8 8 pin mounting jack according to FCC68 Mating connector Modular 8 8 pin plug according to FCC68 Table 8 Pin assignment and status LEDs of 8 pin RJ45 Ethernet front panel connectors LAN1 LAN2 1000Base T 10 100Base T 1 BI DA TX On Link up L 2 BI DA TX Off Link down 3 BI DB RX 4 BI DC On Transmit or receive activity 5 BI DC Off No transmit or receive A 6 BI DB RX activity B Blinking Transmit or receive BI DD i activity 8 BI DD Connection via M12 Connector optional An 8 pin M12 connector can be implemented as an option In this case only one Gigabit Ethernet connection can be used Table 9 Pin assignment of 8 pin M12 Ethernet front panel connector 1000Base T 10 100Base T 1 BI DC 2 BI DD 3 BI DD TN 4 BI DA TX GB 5 BI DB RX Auc BD TX 7 BI DC 8 BI DB RX 2 11 2 Rear I O Connection CompactPCI Serial The CompactPCI Serial standard defines up to eight Ethernet interfaces at the rear To achieve more flexibility these interfaces are not implemented directly on the G20 but on a small adapter card e g the GM1 which is equipped with the CompactPCI Serial connector P6 Two cards with 4 or 8 Ethernet interfaces are already available See MEN S website for ordering information or Chapter 2 13 4 Ethernet Rear I O Card on page 48 MEN Mikro Elektronik GmbH 38 20G020 00 E5 2014 01 21 Functional De
58. scription 2 12 PCI Express 2 12 4 General PCI Express PCIe succeeds PCI and AGP and offers higher data transfer rates As opposed to the PCI bus PCIe is no parallel bus but a serial point to point connection Data is transferred using so called lanes with each lane consisting of a line pair for transmission and a second pair for reception Individual components are connected using switches PCIe supports full duplex operation and uses a clock rate of 1 25 GHz DDR This results in a data rate of max 250 MB s per lane in each direction The standard PCI bus with 32 bits 33 MHz only allows a maximum of 133 MB s If you use only one lane you speak of a PCIe x1 link You can couple several lanes to increase the data rate e g x2 with 2 lanes up to a x32 link using 32 lanes In addition PCIe supports hot plug for instance to exchange defect expansion boards during operation In terms of software most operating systems can handle PCI Express boards just as well as the old PCI 2 12 2 Implementation on G20 On G20 the two Gigabit Ethernet channels are permanently connected via two PCIe x links Another five x1 links are available for use via rear I O One x1 link is led to the board to board connector for the Ethernet rear I O card See Chapter 2 13 4 Ethernet Rear I O Card on page 48 The platform controller hub of the G20 provides two additional PCI Express links over the PEG PCI Express Graphics ports which are also led to t
59. should be made directly to those companies Conformity MEN products are no ready made products for end users They are tested according to the standards given in the Technical Data and thus enable you to achieve certification of the product according to the standards applicable in your field of application MEN Mikro Elektronik GmbH 12 20G020 00 E5 2014 01 21 About this Document RoHS Since July 1 2006 all MEN standard products comply with RoHS legislation Since January 2005 the SMD and manual soldering processes at MEN have already been completely lead free Between June 2004 and June 30 2006 MEN s selected component suppliers have changed delivery to RoHS compliant parts During this period any change and status was traceable through the MEN ERP system and the boards gradually became RoHS compliant WEEE Application The WEEE directive does not apply to fixed industrial plants and tools The compliance is the responsibility of the company which puts the product on the market as defined in the directive components and sub assemblies are not subject to product compliance In other words Since MEN does not deliver ready made products to end users the WEEE directive is not applicable for MEN Users are nevertheless recommended to properly recycle all electronic boards which have passed their life cycle Nevertheless MEN is registered as a manufacturer in Germany The registration number can be provided on request Copyrig
60. specification but not supported on this board MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 DEMENS Functional Description Pin Assignment of Connectors P2 P3 and P4 Connector type of P2 P3 P4 96 pin Airmax VS 4 pair right angle header 8 rows 2 walls Table 11 Pin assignment of CompactPCI Serial P2 connector es aea EEE A ime sue GND ME ND 8 1_ppp_ 1P dos ve 1 DDP 1D ge ip GND Ml uius GND NE CND o2 IDP o2 CNP DNUS 7 2PE 2 PE 2PE 2 PE_ 2_PE_ 2 PE_ 2 PE_ 2 PE Fx07 Fx07 EAS Txo Dore DO Pxos noc ERO Txos Txos RM 2 PE 2_PE_ opa Pee 2 PE_ 2 PE_ 2_PE_ 2 PE_ CND Rx05 Rx05 END Tx05 Tx05 CND Rx04 Rx04 END Tx04 Tx04 5 2PE 2 PE_ 2_PE_ 2_PE_ PPE 2 PE_ 2 PE_ 2 PE_ Hx03 Rxo3 MERO Txos Txog RO Rxo2 Rxozr ODE Txo2 Txoz eee 4 Ope Spe ape 2 _PE_ ape 2 PE_ PE PIPE CND Axot rxo1 MGODI Txo Txor MOADE Roo Rxoo MOADE Txoo Too 1PE 1_PE_ 1_PE_ 1_PE_ 1PE 1_PE_ 1PE 1PE Fx07 Fx07 A Txo7 7x07 EO Rxos rxos RS Txos Txost BS gt 1PE 1PE 1PE 1PE 1PE 1PE 1PE 1PE CEND Rx05 Rx05 END Tx05 Tx05 CND Rx04 Rx04 END Tx04 Tx04 1 L K J H G F E D C B A MEN Mikro Elektronik GmbH 43 20G020 00 E5 2014 01 21 Functional Description 8 SA 8 SATA 8 SATA 8 SATA 7 SATA 7 SATA 7 SA 7 SA TA Rx _Rx END Tx _TX CND Rx _Rx END TA Tx
61. st when installing the G20 in a system for the first time and with minimum configuration M M M M M M M Power down the system Remove all boards from the CompactPCI system Insert the G20 into the system slot of your CompactPCI Serial system making sure that the CompactPCI Serial connectors are properly aligned Note The system slot of every CompactPCI Serial system is marked by a tri angle on the backplane and or at the front panel It also has red guide rails Connect a USB keyboard and mouse to the USB connectors at the front panel Connect a display to the Display Port connector at the front panel MEN offers a DisplayPort to DVI D Adapter as an accessory See MEN s web site for ordering information Power up the system You can start up the BIOS setup menu by hitting the lt F2 gt key see Chapter 3 BIOS on page 54 Now you can make configurations in BIOS see Chapter 3 BIOS on page 54 Observe the installation instructions for the respective software MEN Mikro Elektronik GmbH 22 20G020 00 E5 2014 01 21 Getting Started 1 4 Troubleshooting at Start up If you have any problems at start up of the G20 you can start the board with UEFI default settings for troubleshooting Please refer to Chapter 3 BIOS on page 54 1 5 Configuring BIOS The G20 is equipped with an InsydeH2O UEFI framework Normally you won t need to make any changes in the BIOS setup If you do however you find further detai
62. ted Configuring the Hardware You should check your hardware requirements before installing the board in a system since most modifications are difficult or even impossible to do when the board is mounted in a system The following check list gives an overview on what you might want to configure M CompactFlash board versions 00 and 01 The board is shipped without a CompactFlash card You should check your needs and install a suitable CompactFlash card Refer to Chapter 2 8 1 1 Inserting and Extracting a CompactFlash Card on page 28 for details on the IDE interface microSD card The board is shipped without a microSD card You should check your needs and install a suitable microSD card SS Refer to Chapter 2 8 2 microSD Card on page 29 mSATA board versions 02 and 03 The board is shipped without an mSATA disk You should check your needs and install a suitable mSATA disk SS Refer to Chapter 2 8 3 mSATA Disk on page 31 M Ethernet via rear I O according to CompactPCI Serial The G20 offers the possibility to realize a different number of Ethernet ports at the rear via a special adapter card In that case no CompactFlash or mSATA can be used and no battery is available to buffer the real time clock SS See Chapter 2 13 4 Ethernet Rear I O Card on page 48 MEN Mikro Elektronik GmbH 21 20G020 00 E5 2014 01 21 Getting Started e 1 3 Integrating the Board into a System You can use the following check li
63. tem Date hh Hours Valid range from O to 23 mm Minutes Valid range from 0 to 59 SS Seconds Valid range from 0 to 59 Description Change the date Options MEN Mikro Elektronik GmbH 20G020 00 E5 2014 01 21 mm Month Valid range from 1 to 12 dd Day Valid range from 1 to 31 yyyy X Year Valid range from 2000 to 2099 BIOS 3 2 Advanced InsydeH20 Setup Utility Rev 3 5 F1 Help TV Select Item F5 F6 Change Values F9 Setup Defaults Esc Exit lt gt Select Menu Enter Select gt Sub F10 Save and Exit menu MEN Mikro Elektronik GmbH 0000 57 20G020 00 E5 2014 01 21 BIOS Boot Configuration Sub menu NumLock 0n Power Supply Type AT Watchdog Off PWRON after PWR Fail On ATX PWRGD Failure Mode Check at Start Up External PS Control Switched Platform Reset Management RESET IN is enabled Spread Spectrum Control On Numlock Description Selects power on state for Numlock Options On Off Power Supply Type Description Selects the type of power supply Options AT ATX Watchdog Description Enables or disables the Axxx Watchdog Options Off 10 min 1 min 15 min 2 min 20 min 5 min 30 min PWRON after PWR Fail Description Sets the system power status when power returns to the system from a power failure situation Options On Off Former State ATX PWRGD Failure Mode Description Determines the system behavior in case of a failure at the ATX power good signal Options Check
64. tem shutdown or if the system is in S4 or in S5 state the hot swap LED lights continuously If the system is plugged into the system slot and in SO state or in S3 state the board controller ignores the hot swap switch If the hot swap switch is closed while the hot swap sequence is in progress the board controller stops flashing the hot swap LED and no longer waits for system shutdown If the hot swap switch is closed after system shutdown the board controller initiates Power Resume If the hot swap switch is open during power up the board controller delays the power up sequence and lights the hot swap LED until the hot swap switch is closed 2 15 3 User LEDs The user LEDs can be switched on and off using the MEN driver for the board controller See MEN s website for further information MEN Mikro Elektronik GmbH 53 20G020 00 E5 2014 01 21 BIOS The G20 is equipped with an InsydeH2O setup utility from Insyde Software InsydeH2O is Insyde Software s firmware product line designed to replace traditional PC BIOS It is an implementation of the Intel s Platform Innovation Framework for UEFI EFI The UEFI EFI specification defines a new model for the interface between operating systems and platform firmware This interface consists of data tables that contain platform related information plus boot and runtime service calls that are available to the operating system and its loader Together these provide a standard environment for b
65. the component whenever the components are separated from the system Store the board only in its original ESD protected packaging Retain the original packaging in case you need to return the board to MEN for repair MEN Mikro Elektronik GmbH 9 20G020 00 E5 2014 01 21 About this Document About this Document This user manual is intended only for system developers and integrators it is not intended for end users It describes the hardware functions of the board connection of peripheral devices and integration into a system It also provides additional information for special applications and configurations of the board The manual does not include detailed information on individual components data sheets etc A list of literature is given in the appendix History Issue Comments Date E1 First issue 2010 12 08 E2 Added description of AMT functionality new board 2011 11 17 versions 02 and 03 with mSATA disk GM1 instal lation DisplayPort adapter examples pin assign ment of CompactPCI Serial rear connectors E3 Clarified description of Ethernet rear I O card cor 2012 03 09 rected front panel drawing clarified description of CompactPCI Serial backplane E4 Update removed peripheral slot option modified 2012 10 26 Chapter 2 3 Intel Active Management cosmetics E5 Removed 8 GB DRAM option added Ethernet port 2014 01 21 number for AMT added RTC accuracy corrected screw type for mSATA insta

20G020-00 E5 User Manual - Diamond Point International

Contents

Download Pdf Manuals

Related Search

Related Contents