Home

WRC-1000 Wireless Routing Center

1. Figure 4 14 DHCP Lease Table User s Manual Configuration for Bridge Mode A bridge connects two or more LANs and it bases the forwarding decision on the MAC address In Bridge mode filters forwarding and routing do not apply To set up the bridge mode perform the procedures below Part 1 Enable bridging function Go to the WAN configuration page and select the Bridging option in the WAN LAN Relation field and then click Apply to commit the changes WAN Configuration This page configures the WAN interface General WAN LAN Relation NAT Routing Bridging Figure 4 15 Enabling Bridging Part 2 LAN configuration Inthe General gt Protocol field select Manual Config or DHCP Client as required DHCP Client Select this option if your network already has a DHCP server that assigns IP to this bridge If enabled no further configuration is needed since the DHCP server will pass the required IP information Click Apply to submit your changes NOTE After registering the setting your configuring computer may lose connection to the Wireless Routing Center To reconnect you will need to make sure the computer uses an IP address in the same subnet as the Wireless Routing Center 4 16 Configuration for Bridge Mode LAN Configuration This page configures the LAN interface It also applies on Wireless LAN interface General MAC Address 00 90 96 1D 12 45 Protocol Manual Config DHCP Client
2. Leave the other items in the default setting x Name and Protocol Assign a name and protocol for the client Type a friendly name and protocol for the client Friendly name WRC A 0004P Protocol RADIUS bal Figure B 1 Add Client window Click Next Appendix B 5 Set Client address Enter the IP address of the access point and RADIUS server In this example 192 168 10 1 is set Set Shared secret Enter the password for communication between the access point and the RADIUS server In this example my shared secret is set Leave the other items in the default setting Add RADIUS Client xi Client Information Specify information regarding the client Client address IP or DNS fi 92 168 10 1 Verify Client Vendor JRapius Standard T Client must always send the signature attribute in the request Shared secret Confirm shared secret lt Back Cancel Figure B 2 Add RADIUS Client window Click Finish Step 2 Setting Remote Access Policies 1 Select Remote Access Policies in the Tree window and click the right mouse button 2 Select New Remote Access Policy from the menu B 7 User s Manual 3 Set Policy friendly name In this example WRC 1000AP is set Add Remote Access Policy xj Policy Name Specify a friendly name for the policy 4 Remote Access Policy is a set of actions which can be applied to a group of users meeting certain conditions
3. Set a value in the Time out field In this example set 5 Wireless LAN Security Configuration This page configures the Wireless LAN Security interface 802 1x 802 1 O Not Used Used WEP Key Distribution O Disable Enable Key Length O B4bits 128bits Disable Enable IP Address Port Shared Secret Time out EC 192 168 10 10 1812 ecccccccccecces 5 RADIUS Servers 2 0 0 0 0 1812 5 3 0 0 0 0 1812 s 4 0 0 0 0 1812 5 Access Control MAC Address Access Control Disable Enable Comma separation Ex 11 22 33 44 55 66 aa bb cc dd ee ff i Allow List Apply Figure B 7 Setting the 802 1x and RADIUS groups window B 11 User s Manual Wireless LAN station The following provides the setting procedure for the Wireless LAN station Step 1 Certificate issuance and installation First have the certificate organization issue a certificate and store it in the local computer 1 Temporarily have the station join the wired LAN network 2 Start the Internet Explorer and connect to the following URL http the CA s IPaddress certsrv Then install the certificate according to instructions on the screen Microsoft Certificate Services Microsoft Internet Explorer File Edit View Favorites Tools Help Qa x A CD search se ravortes Aui O R Address 2 http 192 168 10 10jcertsrvi Microsoft Certificate Service Welcome You use this web site to req
4. ceeeecceeceeeeeeeeeeneeeeeeeseeeneseeeeeseeseeseeeeeseeeeeseeneees 2 2 BACK AE AE A EE E N E E E susuceereresseneccrees 2 2 INdiCatorS nesauesinnnnana na ARN ATAA ENN 2 3 Front FANG es sccatnoe seuvaxecenncaveaxe a E S E 2 3 CED INdICAlO Sianas ieaiaia an EE EE AA 2 4 6S 1 1 o eee E ee A E E E aESE 2 5 Screws for wall mount ccceceeeeseseeeeeeseeeeeseeeeesneeeeesesesenseeeeeeneenees 2 5 AC adapter and power cord sccceceeeceeseeeeeeeseeeeeseeeeesneneeeeeseeeeeeeees 2 6 xi Chapter 3 Setup MOUntiNG soriana eaea a ees AA ai edaceh tt nc AAAA 3 2 Vertical MOUNTING c 3 2 Florizontal MOUNTING ccccssssastccee evs arn a acces hiaecd ee 3 3 Wall MOUMtMNG ess a 3 4 AG Ce 0 ena nce ie Sn Soe onsen ae aaa aae SES aoe eee 3 4 Connecting the Wireless Routing Center ccssssseereeeeesees 3 5 Setting up the Ethernet Wireless LAN client sssseeees 3 7 Setting up Ethernet Client ce eeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeetaaeeeees 3 7 Setting up Wireless client 20 eeceeececeeeeeeeeeeeeeeaeeeeecaeeeeeeeeeeeeaeeeees 3 11 Checking Connection with the Wireless Routing Center 3 12 Chapter 4 Web Configuration Accessing Web Configuration Page ssscccssecssseeesseeesseeeeees 4 2 To enable your settings ccccceseeseeeeeeeseeeeeeeeeeesneeeeeeeeensneceeeeeeeneees 4 7 Viewing System Overview and 1OG essseeeceeeeeseeeeeeeeeeesneeeeeeeeenenees 4 7 O
5. Figure 4 16 Bridge Mode DHCP Client Manual Config If enabled manually enter the IP address its subnet mask and default gateway in IP Address Subnet Mask Default Gateway fields NOTE To reconnect after committing this setting you will need to make sure the computer uses an IP address in the same subnet as the manually entered IP LAN Configuration This page configures the LAN interface It also applies on Wireless LAN interface General MAC Address 00 90 96 2C 76 BC Protocol Manual Config DHCP Client IP Address 192 168 10 1 i Subnet Mask 255 255 255 0 Default Gateway 192 168 10 1 Apply Cancel Figure 4 17 Bridge Mode Manual Config User s Manual Wireless LAN Configuration The Wireless Routing Center implements Access Point capability which connects wireless clients to a wired LAN It allows wireless nodes to access network resources and share the broadband Internet connection With the default values the router Access Point can be easily associated by a wireless client We suggest that you customize the wireless settings to prevent unauthorized association NOTE One Wireless Routing Center can accommodate multiple computers However optimal LAN operation can be maintained with up to 10 computers Wireless LAN Configuration This page configures the Wireless LAN interface Craneo Dov Figure 4 18 Wireless LAN Configuration Basic Access Point Nam
6. tions are terminals forexample comput ers with a wireless LAN card installed that can communicate with acommon access point but are in a position where the signals from one cannot reach the other If hidden terminals try to contact the access point at the same time their trans missions cannot be properly received and retries will result thereby degrading LAN operation IEEE 802 1x A standard for verifying users on a LAN Transmissions from unverified users are blocked Only verified users are allowed to transmit on the LAN Glossary 2 TEEE802 11b TEEE802 11 A wireless LAN standard that enables data trans mission at a speed of 11 Mbps and a wave length of 2 4GHz Devices can be located up to 100 meters from the access point infrastructure mode When the LAN transmissions are made through an access point IP address Internet Protocol Address is a unique 32 bit addresses assigned to each node on networks that use IP ISP Internet Service Provider is acom pany that provides server computers for connection to the Internet L local IP address A local Internet Proto col Address is a unique 32 bit addresses assigned to each node on a LAN using the TCP IP standard LAN A Local Area Network is acom puter network limited to the immediate area usually the same building or floor of a building MAC address The Media Access Control address is your computer s unique hardware number that identifies itonaL
7. 13 seconds Wireless LAN Interface Access Point Name WRC 1000_AP SSID WRC_Network Channel ID 10 BSSID 00 90 96 2 73 3a Figure 4 8 Overview Configuration Filter Log If filter feature is enabled you can click the Log link in Status menu to display the filter activity log See Viewing Filter Log for more information on log category Activity Log This page displays router log i Time Category Possible reason Source MAC Destination MAC SourcelP Destination IP Protocol Source_Port Type Dest_PoriCode Figure 4 9 Activity Log Configuration for NAT Routing Mode Configuration for NAT Routing Mode Before you configure your Wireless Routing Center you must decide whether to configure the Wireless Routing Center as a router or as a bridge This section describes only how to set up the Wireless Routing Center as a router For instruc tions on bridge configuration refer to the section Configuration for Bridge Mode in this chapter When operating as a router the Wireless Routing Center communicates with your ISP through the WAN port Depending on the connection type offered by your ISP you may get the WAN IP address by one of the following means DHCP Client In this connection type your router acts as a DHCP client and requests IP information from the DHCP server on the ISP side Select this option if your ISP assigns you a dynamic IP addre
8. IV Microsoft Encrypted Authentication version 2 MS CHAP v2 IV Microsoft Encrypted Authentication MS CHAP T Encrypted Authentication CHAP I Unencrypted Authentication PAP SPAP Unauthenticated Access r Allow remote PPP clients to connect without negotiating any authentication method Cancel Apply Figure B 6 Edit Dial in Profile window ClickOK Click Finish Access point The following is the setting procedure for the access point Step 1 Setting the 802 1x function at the access point Make settings for the 802 1x function The following procedure is to enable the 802 1x function The other settings of the Wireless LAN page is omitted 1 Open the default page on the Web B 10 Appendix B 2 Select the Wireless LAN Security page 3 802 1x group Select Used in the 802 1x field Select the Enable radio button in the WEP Key Distribution field Select the 128bits radio button in the Key Length field 4 RADIUS group Select the 1 Enable radio button inthe RADIUS Servers field Set a value in the IP Address field Enter the IP address of the RADIUS server In this example set 192 168 10 10 Set a value in the Port field In this example set 1812 Set a value in the Shared Secret field Shared secret is a password for communication between the access point and the RADIUS server In this example set my shared secret The characters you enter in this field will be displayed as
9. NOILWHNDIANOZ aaM User s Manual 3 Ifrequired in the MAC Address field enter your network adapter s MAC address in the format of xx xx xXx XX XxX xx Otherwise keep the default values This field allows you to copy a network adapter s MAC address to the WAN port of the Wireless Routing Center Some ISPs use the MAC address of the NIC which was connected to the Cable ADSL modem for static mapping This would give you the same IP address each time the Cable ADSL modem requests an IP address for the Ethernet port If this is the case this feature removes the need of asking your ISP to change the registered MAC address You can still use the same IP you were given for the router s WAN port 4 Inthe Host Name field you can supply a host name for the Wireless Routing Center if this is required by your ISP Some ISPs only respond to a DHCP request with a valid Host Name If a host name is not necessary for your ISP leave it blank Part 2 Configuring protocol settings Proceed to the section corresponding to the connection type you selected above gt DHCP Client If DHCP Client is your option no other configuration is needed Click Apply to end your WAN settings After the connection to ISP is established the information provided by your ISP will be displayed in the DHCP client group WAN Configuration This page configures the WAN interface General WAN LAN Relation NAT Routing Bridging Protocol DHCP
10. Up to 12 entries are allowed For example to allow or prohibit local computers 192 168 10 140 192 168 10 150 to use ping service using UDP port 53 IP Start IP End Port Start Port End 192 168 10 140 192 168 10 150 53 53 4 24 Filters Filter Scenario of the Wireless Routing Center When setting up your filter policies note the filter scenario used by the router When Filter Type is Listed Block If all filters are disabled No filter rule is specified to block any packet All packets can pass through the WAN port Defaults If any filter is enabled only the packets matching the specified rule are blocked other packets can pass through the WAN port When Filter Type is Listed Pass If all filters are disabled No filter rule is specified to allow any packet to pass All packets are blocked If any filter is enabled Only the packets matching the specified rule can pass other packets are blocked Filters Configuration This page configures LAN filters The LAN machines blocked by the filters will not be able to communicate through the WAN but will be able to communicate with each other and with the router itself General Figure 4 21 Filters Configuration 4 25 WEB CONFIGURATION User s Manual Viewing Filter Log When the filter feature is enabled the router will keep a record of the packets discarded To view the firewall ac
11. in the Max Idle Time box If your Internet account is billed based on the amount of time of your Internet connection you can reduce charges by enabling this option Enter an idle time value best suited for your network MTU MRU Allows you to adjust the Maximum Transmission Receive Unit in bytes for the WAN interface You may need to adjust the values to a smaller size if the servers of your ISP do not support full size frame packets Packets larger than the specified values will be fragmented which could hurt performance It s better not to modify the MTU MRU settings unless your ISP advises you to NOILWHNDIANOD aaM After you finish the WAN settings click Apply to submit your changes User s Manual WAN Configuration This page configures the WAN interface General WANI LAN Relation NAT Routing Bridging Protocol DHCP Client PPPoE Client Manual Config MAC Address 00 90 96 1d 12 44 Host Name PPPoE Client PPPoE Connection Status Down Username l Password l Authentication Mode O Auto O PAP CHAP Fomnection Mode 5 eae Demand Max Idle Time 5 min MTU 11454 MRU 11454 Figure 4 11 WAN Configuration PPPoE Client gt Manual Config If Manual Config is your option configure these fields as required by your ISP IP Address Subnet Mask Enter the fixed IP address and subnet mask given by your ISP The default values are 0 0 0 0 0 0 0 0 Default Gateway The IP address of the de
12. properly configure the network settings of your Ethernet or wireless client com puter As the Wireless Routing Center is configured with the default IP address of 192 168 10 1 and subnet mask of 255 255 255 0 and its DHCP server is enabled by default you can configure your computer s TCP IP settings as one of the following 1 To use dynamic IP Set your computer to be DHCP client to accept the dynamic IP from the router 2 To use static IP Set the IP address as 192 168 10 x x is between 2 and 254 subnet mask as 255 255 255 0 and the gateway as 192 168 10 1 to be on the same subnet with the router This section describes how to configure your computer to be a DHCP client for initial connection to the Wireless Routing Center If you have modified the Wireless Routing Center s network setting your LAN Wireless LAN clients should make appropriate changes in order to make a successful connection Setting up Ethernet client To access the Wireless Routing Center via Ethernet make sure your computer is equipped with an Ethernet network card and has an appropriate network card driver and TCP IP installed NOTES 1 If TCP IP protocol is not installed on your computer refer to Windows documentation for installation instructions 2 For initial verification connect only one computer directly to an Ethernet port on the Wireless Routing Center not through a hub Connecting more than one computer may cause setting errors For Windows
13. Client PPPoE Client Manual Config MAC Address 00 90 96 1d 12 44 Host Name DHCP Client IP Address Subnet Mask 0 0 0 0 0 0 0 0 Default Gateway DNS Servers WINS Servers 0 0 0 0 Domain Name Figure 4 10 WAN Configuration DHCP Client 4 10 Configuration for NAT Routing Mode gt PPPoE Client If PPPoE Client is your option configure these fields as required by your ISP PPPoE Connection Status This item is not configured It displays whether the connection is up or down Username Password Enter the user name and password provided by your ISP for logging onto the Internet Authentication Mode Usually you should select Auto When Auto is selected the Wireless Routing Center automatically determines whether the mode is PAP or CHAP and makes the connection If a connection cannot be made with the Auto setting check with your ISP and set either PAP or CHAP Connection Mode Select Keep Alive or Connect on Demand Keep Alive This feature will keep your PPPoE enabled Internet connection always open This is done by sending echo requests periodically to the ISP to prevent the connection from being terminated by the ISP Connect on Demand If enabled the router will trigger a PPP session for connection to the Internet if any client computer on your LAN sends a request for Internet access However the router automatically disconnects the PPP session after the WAN connection has been idle for the amount of time specified
14. License required for indoor use Use with outdoor installations not allowed E necessaria la concessione ministeriale anche per I uso interno Verificare con i rivenditori la procedura da seguire L uso per installazione in esterni non e permessa Nederland License required for outdoor installations Check with reseller for procedure to follow Licentie verplicht voor gebruik met buitenantennes Neem contact op met verkoper voor juiste procedure USA Federal Communications Commission FCC This device complies with Part 15 of FCC Rules Operation of the devices in a Wireless LAN System is subject to the following two conditions This device may not cause harmful interference This device must accept any interference that may cause undesired operation TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the TOSHIBA Wireless Routing Center WRC 1000 or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA The correction of interference caused by such unauthorized modification substitu tion or attachment will be the responsibility of the user CAUTION Exposure to Radio Frequency Radiation The radiated output power of the TOSHIBA Wireless Routing Center WRC 1000 is far below the FCC radio frequency exposure limits Nevertheless the TOSHIBA Wireless Routing Center WRC 1000 shall be used in such a manner that the po
15. TOSHIBA WRC Finder MAC Address IPAddess SSID Chamet Click Search to find Access Points Figure 4 2 WRC_FIND EXE 2 Follow the steps below to find Wireless Routing Center 1 A dialog box will be displayed asking you if you want to search for Wireless Routing Centers TOSHIBA WRC Finder File F Help H Search Exit Search Click Search to find Access Points Figure 4 3 Confirmation window 2 Ifyou click No WRC Finder will do nothing At this point you can still continue by clicking Search 3 Ifyou click Yes the Wireless Routing Center search will begin In about five seconds a list of Wireless Routing Centers will be displayed 4 3 User s Manual 4 When the WRC Finder locates a Wireless Routing Center the following information will be displayed Access Point Name Wireless LAN s Access Point Name MAC Address Access Point s MAC Address IP Address WRC 1000 s IP Address SSID SSID Channel The channel that is being used TOSHIBA WRC Finder File E Help H Access Point Name MAC Address IP Address WAC 1000_4P 00 90 96 25 9b 4b 192 168 10 1 WARC Network 10 2457 MHz Click Access to view modify selected AP s setting Figure 4 4 WRC information 5 If no Wireless Routing Center is found the Confirm dialog box is displayed again 3 Open the Web Configuration page Double click the Wireless Routing Center you want to set The Web browser will st
16. XP 1 From the Start menu point to Connect To and then click Show all connections 3 7 dag SETUP User s Manual 2 Right click the Local Area Connection icon and then click Proper ties 3 Inthe General window highlight Internet Protocol TCP IP and then click Properties 4 Enable Obtain an IP address automatically and then click OK Internet Protocol TCP IP Properties General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain DNS server address automatically Use the following DNS server addresses Figure 3 8 Obtain an IP address automatically Checking Renew IP Address under Windows XP The following steps help you verify that your network adapter gets an IP address within the DHCP IP pool range 192 168 10 100 192 168 10 150 by default of the Wireless Routing Center If not you may need to renew the IP information 1 Click Run from the Start menu to open the Run dialog box 2 Type cmd in the dialog box and then click OK 3 At the prompt type ipconfig to see the IP information from DHCP server 4 If you want to get a new IP address type ipconfig release to release the previous IP address and then type ipconfig renew to get a new one 3 8 Setting up the Ethernet Wireless LAN client For Windows 2000 1 Fromthe Start menu
17. as a connection point between a network and the Internet and serves as an agent for computers in the network Proxy server can refer to either a computer or to a software server R RADIUS A verification system for client server dial up connections It verifies the user making a dial up con nection to the access server Rejectunspecified networkname A function that restricts access to the LAN to terminals that have the same network name as that of the access points router A device or software pack age that handles the connection be tween 2 or more networks Routers spend all their time looking at the destination addresses of the packets passing through them and deciding which route to send them on routing Determining the path for a packet to travel and managing the trans mission of the packet routing table A table containing rout ing information such as network ad dress the next relay router and hop count Glossary 3 AYVSSO1 GLOSSARY static routing S static routing A routing system in which routes are set manually subnet mask Determine what subnet an IP address belongs to switching hub A multiport bridge that receives data packets compares the address to an address table and relays the data to the proper port T TCP IP Transmission Control Proto col Internet Protocol are protocols data transmission over the Internet TCP Transmission Control Protocol is a protocol
18. communicate If WEP is disabled If WEP is disabled the Authentication Mode is automatically set to Open WEP Key Type and WEP Keys For flexibility you can enter the WEP keys in either ASCII or Hexadecimal format Select a format and then enter the key values in the WEP keys 1 4 fields All four fields need to be entered Note that when using Hexadecimal format only digits 0 9 and letters A F a f are allowed Valid key length for each encryption type is as below HEX Format ASCII Format Q E S 64 bit 10 hexadecimal digits 5 ASCII characters 5 cm 128 bit 26 hexadecimal digits 13 ASCII characters gt z fej zZ Aside from entering your WEP keys you should select one of the four keys to encrypt the data before being transmitted The AP always transmits data encrypted using this WEP key The key number 1 2 3 4 is also transmitted The receiving station will use the key number to determine which key to use for decryption If the key value does not match with the transmitting station the decryption will fail To ensure successful decryption have your wireless stations set identical key tables NOTE All Wireless Stations must use identical encryption algorithm level and Key values same key position in its key table to ensure successful data transmission 4 21 User s Manual Access Control MAC Address Access Control The Wireless Routing Center also supports authentication based on the MAC address of a wireless cli
19. handbook and the Canadian Electrical Code Part II C 1 9 Xianaday User s Manual The following illustrations show the plug shapes for the U S A and Canada the United Kingdom Australia and Europe USA and Canada United Kingdom a Oo UL approved BS approved 5 CSA approved a Australia Europe lt AS approved Approved by the appropriate agency C 2 Glossary The terms in this glossary cover the topics discussed in this manual 10Base T 100Base TX Two standards for Ethernet data transmission speeds 10Base T transmits at 1OMbps and 100Base TX transmits at 100Mbps A access point name The access point name is used to identify a device access point in a wireless LAN environment ADSL Asymmetric Digital Subscriber Line is a modem technology that en ables high speed data communications over existing phone lines A splitter enables simultaneous transmission of voice fax and digital data bridge A bridge connects LANs They also improve efficiency of transmission within a LAN A basic bridge has ports connected to two or more otherwise separate LANs Packets received on one port may be retransmitted on another port A bridge will not start re transmis sion until it has received the complete packet Therefore stations on either side of a bridge may be transmitting simulta neously without causing collisions C channel The channel is the radio frequency us
20. if the Wireless Routing Center s default of 192 168 10 1 is used If you want to configure the IP address refer to the Setting up the Ethernet Wireless LAN client section in Chapter 3 Setup for more information 5 5 SNILOOHS31ENOY L User s Manual A IP Configuration Iof xi r Ethernet Adapter Information Intel 8255x based Integrated Fas 7 Intel 8255 based Integrated Fast Ett Adapter Address Toshiba Wireless LAN Card IP Address PPP Adapter rov Subnet Mask 255 255 255 0 Default Gateway 192 168 10 1 Release Renew Release All Renew All More Info gt gt Figure 5 2 Checking the TCP IP setting Cause 4 There are incorrect network settings on the computers Remedy Following the steps below to make sure the computers can communi cate with each other Check the domain name and network sharing settings 1 To open the command prompt click Start point to Programs and Accessories If you are using Window Me click MS DOS Prompt If you are using Window 2000 click Command Prompt If you are using Windows XP click Start point to All Pro grams Accessories and click Command Prompt to open the Command Prompt 2 Enter a ping command and the IP address Example C ping 192 168 10 100 Press Enter To confirm the IP address of the opposite computer refer to Cause 4 above 5 6 Application problems 3 The following message for example indicates proper communica
21. respective fields NOTE Normally the Administration Configuration Page displays the set values It is a good idea to check these values periodically to make sure they have not been changed To verify the current time refer to the Overview Page gt Management Setup Username and Password For administration security specify the Username and Password and re enter the password for confirmation This setting limits web based manager access to users with the correct credentials By default the user name is admin and the password is password NOTE These are to authorize access to the Web Configuration Page of the Wireless Routing Center They are different from the user name and password used to access an Internet Service Provider 4 30 Administration Configuration WAN Management Available only in NAT Routing Mode If available this item is disabled by default That is any external access from the WAN port will be rejected If this option is enabled a WAN Port field is displayed with the default value of 80 If required you may enter another port number used for external WAN access If WAN Management is enabled using a port other than 80 the router s HTTP service Web Configuration Utility will be accessible via the router s WAN port IP address followed by a colon and the non 80 port http lt WAN IP address gt lt non 80 port gt For example if 1234 is entered the router will be accessible at http 203 1 2 3
22. the following 1 Make sure your computer is equipped with a Wireless LAN adapter and has an appropriate Wireless LAN card driver utility and TCP IP installed 2 Set the Wireless LAN client to obtain a dynamic IP address from the Wireless Routing Center The procedures are the same as described above The only difference is that you are configuring the TCP IP associated with your Wireless LAN card 3 11 SETUP User s Manual 3 Verify that your Wireless LAN setting is identical to the router s default wireless settings Checking Connection with the Wireless Routing Center You can use the Ping command to verify whether or not your Ethernet Wireless client is connected to the Wireless Routing Center To execute ping command open a DOS window and ping the IP address of the Wireless Routing Center at the DOS prompt For example ping 192 168 10 1 If the following response occurs Reply from 192 168 10 1 bytes 32 time 100ms TTL 255 Then the connection between the Wireless Routing Center and the network is OK If you get a failed ping with the response of Request time out Then the connection has not been made Verify your network setting are correct For Ethernet client also check the cable between the Wireless Routing Center and the computer Chapter 4 Web Configuration After you have configured your system as described in Chapter 3 Setup you can proceed with the initial configuration described in this chapt
23. tion Check the network settings of the computers C ping 192 168 10 100 Pinging 192 168 10 100 with 32 bytes of data Reply from 192 168 10 100 bytes 32 time lt 10ms TTL 128 Reply from 192 168 10 100 bytes 32 time lt 10ms TTL 128 Reply from 192 168 10 100 bytes 32 time lt 10ms TTL 128 Reply from 192 168 10 100 bytes 32 time lt 10ms TTL 128 4 The following message for example indicates improper commu nication Check other items of Wireless LAN troubleshooting C ping 192 168 10 100 Pinging 192 168 10 100 with 32 bytes of data Request timed out Request timed out Request timed out Request timed out 5 If you want to configure IP address refer to the Setting up the Ethernet Wireless LAN client section in Chapter 3 Setup for more information Application problems Some network applications do not work Cause Remedy The Wireless Routing Center uses NAT to convert the IP addresses and port numbers in the headers of packets in communication between LAN and WAN Therefore applications that use IP addresses and port numbers kept in the data part of packets may not work as expected due to differences between the packet header and packet data in terms of IP addresses and port numbers Applications using a protocol other than TCP UDP might not operate properly due to non conversion of port numbers by NAT because there is no port number in the header These applications do not operate normally with the Wireless
24. to establish a connection between two computers It the includes error correction for packet transmission Compare UDP U UDP User Datagram Protocol is part of the TCP IP suite of protocols UDP is a connectionless protocol for data trans mission that does not acknowledge whether packets are received or not It enables faster performance but there is no assurance of an accurate transmis sion UPnP Universal Plug and Play is de signed to support zero configuration It allows Windows XP to automatically configure the Router for various Inter net applications such as Windows Messenger Glossary 4 W WAN Wide Area Network covers a larger area than a LAN See also LAN WEP key See encryption wireless LAN access point A terminal on a wireless LAN or an interface be tween a wireless LAN and a wired LAN wireless LAN PC A personal comput er connected to a LAN through radio communication wired LAN PC A personal connected to an Ethernet LAN by cable Index A AC adapter 2 6 3 4 AC Power Cord and Connectors C 1 Administration configuration 4 30 management setup 4 30 system clock 4 30 Bridge mode 4 16 Browser 4 2 C Configuration 4 1 features list 1 3 overview page 4 5 4 6 retrieve 4 33 save 4 33 WEB configuration page 4 2 D DC IN jack 2 2 Defaults load default switch 2 2 restore 4 33 values A 1 DHCP 1 2 E Encryption 4 21 Ethernet features 1 1 F Filters log
25. to the IP address of the LAN s Wireless Routing Center If DHCP server is enabled enter the fields below DHCP Lease Time Specify the time that a network device can lease a private IP address before the DHCP server reassigns the IP address Configuration for NAT Routing Mode IP Pool Range Specify the starting and ending IP address of the IP address pool Whenever a network device requests an Internet session the router will allocate an unused IP address from this pool and lease it to the device for a specified amount of time LAN Configuration This page configures the LAN interface It also applies on Wireless LAN interface General MAC Address 00 90 96 1D 12 45 Manual Config IP Address 192 168 10 1 Subnet Mask 255 255 255 0 DHCP Server Service Enabled Disabled DHCP Lease Time 72 hour s IP Pool Range 192 168 10 100 192 168 10 150 Figure 4 13 LAN Configuration in Router Mode Viewing Current DHCP Assignments When the DHCP server function is enabled for your LAN the Wireless Routing Center keeps a record of any computer either Ethernet or Wireless node that has leased an IP from the specified IP pool The DHCP lease table is displayed under Overview gt LAN Interface LAN Interface MAC Address 00 90 96 1D 12 45 IP Address Subnet Mask 192 168 10 1 255 255 255 0 DHCP Server Enabled MAC Address P Address Expires In Active DHCP Leases 00 c0 d0 20 4f61 192 168 10 100 33 seconds
26. top positions SYSTEM INDICATORS Figure 2 1 Front left and top of the Wireless Routing Center System The system indicators provide LEDs for monitoring the indicators Power Wireless LAN LINK Wireless LAN ACT WAN Ethernet 1 Ethernet 2 Ethernet 3 and Ethernet 4 2 1 YNO L GNVHS IHL THe GRAND Tour User s Manual Bottom and right Figure 2 2 shows the Wireless Routing Center s bottom and right sides RUBBER PADS Figure 2 2 The bottom and right sides of the Wireless Routing Center Notches Use these notches to hang the Wireless Routing Center from screws in a wall Rubber pads Use these pads to horizontal mount the Wireless Routing Center Lay it on a flat surface with the pad side down Mounting hole Fit pin on the stand into mounting hole to use the Wireless Routing Center in an upright position Back Figure 2 3 shows the Wireless Routing Center s back side 5VDC On OrF Loan DEFAULT Se LAN ports 1 4 WAN port Figure 2 3 The back side of the Wireless Routing Center 2 2 5VDC oC DC IN 5V Indicators Power connector CAUTION Always use the correct AC adapter to avoid the risk of fire or damage to your Wireless Routing Center The current rating for the Wireless Routing Center is 2 0 amperes On Off b LAN ports 1 4 LAN WAN port WAN Load Default INIT Power switch An integrated four port 10 100BaseT switch pro
27. 1234 where 203 1 2 3 indicates the WAN port s IP address If WAN Management is enabled using standard port 80 no suffix is required If WAN Management is enabled using port 80 your publicly accessible Web server if any on the LAN side should use a non 80 HTTP port You will need to use the Forwarding feature to shift external HTTP requests to the non 80 port number used by the Web server on the LAN side WAN Port Ping Reply Available only in NAT Routing Mode If available this setting determines if an external host will get a reply when trying to ping the IP address of your WAN port It is disabled by default WRC Finder Function Via WAN Available only in NAT Routing Mode If enabled the current settings for Wireless Routing Centers will be displayed when a WAN computer launches this function UPnP Available only in NAT Routing Mode It allows Windows XP to automati cally configure the Router for various Internet applications such as Windows Messenger If available it is enabled by default NetBIOS Communication Available only in NAT Routing Mode Port numbers 137 139 and 445 that are used by NetBIOS will be open It is disabled by default 4 31 NOILVHNDIANOD aaM User s Manual Report Log to TFTP Server Available only in NAT Routing Mode If available it specifies whether to report the firewall event log to your TFTP server If enabled aLAN TFTP Server field is present for you to specify the IP address of the T
28. 2 11 Standard on Wireless LANs Revision B as defined and approved by the Institute of Electrical and Electronics Engineers The Wireless Fidelity WiFi certification as defined by the WECA Wireless Ethernet Compatibility Alliance Wireless LAN and your Health Wireless LAN products like other radio devices emit radio frequency electromag netic energy The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations TOSHIBA believes Wireless LAN is safe for use by consumers These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature In some situations or environments the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organization These situations may for example include Using the Wireless LAN equipment on board of aeroplanes or Inany other environment where the risk of interference to other devices or services is perceived or identified as harmful If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment e
29. 4 26 X3QN rules 4 23 types 4 24 Finder See WRC finder Firmware upgrade 4 32 Forwarding 4 26 Indicators icons 2 3 LED table 2 4 location 2 1 Initialize switch See Defaults load default switch L LAN client set up Ethernet 3 7 wireless 3 11 configuration 3 7 connections 3 5 DHCP settings 3 7 IP settings 3 7 ports 2 2 Log 4 7 Mounting horizontal 3 3 vertical 3 2 wall 3 4 Index 1 INDEX User s Manual N Ethernet 5 1 forgotten password 5 8 NAT routing mode 4 9 Linux 5 8 LAN configuration 4 13 power 5 1 WAN configuration 4 9 Wireless LAN 5 3 P U Password 4 5 4 11 User name 4 11 Ping 3 12 Ports 2 2 W Power switch 2 2 WAN R connection 3 5 port 2 2 Reboot 4 33 WRC Finder 4 2 Router features 1 2 Wireless LAN See also Security Routing configuration 4 29 configuration 4 18 S advanced 4 19 basic 4 18 Security 1 3 features list 1 3 802 1x B 1 Configuration Example B 5 Function B 2 Overview B 1 WEP Key B 2 Features list 1 3 Wireless LAN 4 19 802 1x 4 20 access control 4 22 RADIUS Server 4 22 WEP 4 20 Stand 2 5 Startup 3 7 System configuration 4 32 firmware upgrade 4 32 user configurations 4 33 System requirements 1 1 T Troubleshooting 5 1 application problems 5 7 configuration window 5 1 Index 2
30. 5 0 Default Gateway 192 168 10 1 If the TCP IP protocol has not been installed or if the correct IP address has not been set read the manuals for your computer and LAN card and set them accordingly If you want to configure the IP address refer to the Setting up the Ethernet Wireless LAN client section in Chapter 3 Setup for more information Wireless LAN Windows 2000 1 Click Start point to Programs Accessories and click Command Prompt to open the Command Prompt window 2 Enter ipconfig and press Enter 3 Check the values for the IP address and subnet mask IP address 192 168 10 100 192 168 10 150 Subnet Mask 255 255 255 0 Default Gateway 192 168 10 1 If the TCP IP protocol has not been installed or if the correct IP address has not been set read the manuals for your computer and LAN card and set them accordingly If you want to configure the IP address refer to the Setting up the Ethernet Wireless LAN client section in Chapter 3 Setup for more information Windows 98 Me 1 Click Start and Run then enter winipcfg in the input box 2 Check the values for the IP address and subnet mask in the winipcfg dialog box In an ordinary small scale LAN environment the subnet mask is set to 255 255 255 0 In this case confirm that the first three sets of digits of the IP address of the Wireless LAN station are the same as those of the IP address of the Wireless Routing Center It corresponds to 192 168 10 x
31. 8 10 1 and the subnet mask is 255 255 255 0 Note that if you change the private IP address and apply the changes the computer from which you configure the router will lose commu nication to the router To reconnect you will need to renew the IP address of the computer or change to an IP address compatible with the new LAN port IP address 2 Inthe DHCP Server gt Service field select whether to enable DHCP service on the LAN port Wes CONFIGURATION User s Manual 4 14 The Wireless Routing Center implements a built in DHCP Dynamic Host Configuration Protocol server on its LAN interface which dynamically assigns IP addresses to DHCP clients on the LAN Wireless LAN The DHCP server also provides a default gateway the router s LAN IP address and DNS addresses for DHCP clients to access the Internet The DHCP function spares you the hassle of manually assigning a fixed IP address to each computer on the LAN Wireless LAN If your network already has a DHCP server do not enable this function DHCP server is enabled by default NOTE Only one DHCP server can run on one LAN If you decide to enable DHCP on this router remember to disable the DHCP function of the other device If you disable DHCP no further configuration is required for the Wireless Routing Center Click Apply to submit your changes If you enable DHCP proceed to the next step NOTE Set the DNS Server IP address of the computer connected to the LAN port
32. AN MAC address filtering Ensures that only computers that are registered with the device will be allowed access either to the Internet or to a wired LAN routing table medium reservation Reserving the access point for a specific terminal and notification to other terminals not to call It is used to avoid the hidden termi nal problem N NAT Network Address Translation enables multiple users to simultaneous ly share a single global IP address When a computer accesses the Internet the NAT function uses a table to con vert global and local IP addresses and ports network name A network name identi fies groups communicating with each other over a Wireless LAN P port The port port number is used to determine which application should handle a TCP or UDP packet port forwarding Connects a local IP address and port number to a global address When a client computer issues a request to the Internet the request goes through the device which uses the NAT table to connect the client s local address and port number to a global address The reply is received by the device which relays it to the client computer PPP PPP is a protocol to authenticate computers communicating with each other in a network such as a personal computer connected by phone line to a server PPPoE Point to Point Protocol over Ethernet protocol A set of rules used for trans mitting data Proxy server A proxy server acts
33. Analogous to rules you can apply to incoming mail in an e mail application you can specify a set of conditions that must be matched for the Remote Access Policy to apply You can then specify actions to be taken when the conditions are met Policy friendly name waca 0004P lt Back Cancel Figure B 3 Add Remote Access Policy window Click Next 4 Add a Conditions by pressing the Add button This example defines that this policy should be used when Client Friendly Name is WRC 1000AP Various conditions are available For details refer to Windows 2000 online Help Add Remote Access Policy x Conditions Determine the conditions to match Specify the conditions to match Conditions Client Friendly Name matches WRC 10004P Figure B 4 Add a Conditions window Click Next Appendix B 5 Select Grant remote access permission Add Remote Access Policy Figure B 5 Select Grant remote access permission Click Next B 9 User s Manual 6 Click the Edit Profile button and select the Authentication tab Place a check mark in the Extensible Authentication Protocol check box Select Smart Card or other Certificate for the EAP type Edit Dial in Profile 2 xi Dial in Constraints IP Multilink Authentication Encryption Advanced Check the authentication methods which are allowed for this connection Smart Card or other Certificate x Configure
34. FTP server All the filter logs are sent to the TFTP server although only 32 entries are displayed in the Activity Log window see Status gt Log NOTE This function is supported only if the IP address of the TFTP server and that of the Wireless Routing Center are in the same subnet Administration Configuration This page is for administration Management Setup A Q 5 A 5 S 5 7 H Figure 4 24 Administration Configuration System Configuration gt Firmware Upgrade This option allows you to upgrade the Wireless Routing Center with new firmware After upgrading your customized configurations will still be effective Upgrading does not revert to the default settings To upgrade download the firmware file to your host computer and follow the steps below 1 Inthe Locate New Firmware field click Browse to locate the firmware file 2 Click Upgrade A message will be displayed advising you to wait a few minutes You will return to the Administration page when the process is complete 4 32 System Configuration NOTE Do not interrupt the upgrade process You could damage your Wireless Routing Center After the upgrade is complete you can see the new firmware version in the Cur rent Firmware version field gt User Configurations Save Current Configurations Allows you to save your customized settings to the Wireless Routing Center Once your router is proper
35. IP Address DMZ setting allows a local computer to be exposed to the Internet If you specify a DMZ host all virtual service requests not specified in the Forwarding table are forwarded to the DMZ host 4 26 Forwarding TCP Port Forwards In the first Start and End fields define the port range for the incoming TCP service you want to forward In the IP Address field enter the IP address of the virtual server to which packets are forwarded The Start End fields on the right side define the port range for the TCP service on the virtual server For example the setting below allows access on virtual server 192 168 10 210 using FTP service Start End IP Address Start End 20 21 192 168 10 210 20 21 UDP Port Forwards The configuration is the same as setting TCP Port Forwards only that the entry applies to UDP service When the router gets outside TCP UDP requests destined for the WAN port it determines whether the services are allowed according to your forwarding settings For example if you do not specify FTP virtual service in the Forwarding table incoming FTP requests identified by port number in packets are blocked or otherwise sent to the DMZ host if specified On the other hand if an FTP forward ing entry has been set up the FTP requests will be forwarded to the specified computer NOTE If you set multiple forwarding entries they will be used in order from the first entry In the example below incoming FTP requests wi
36. Mode Authentication Mode MAC Address Access Control NAT Routing mode DHCP Client 192 168 10 1 255 255 255 0 enable 72 hours 192 168 10 100 192 168 10 150 WRC 1000_AP WRC_Network 10 disable 100 2346 2346 1 and 2 Mbps 1 2 5 5 and 11 Mbps Not Used disable Open disable A 1 Appenpix A User s Manual Filters Filter Type MAC Filters IP Filters TCP Port Filters UDP Port Filters Administration System Clock set by Username Password WAN Management WAN Port Ping Reply WRC Finder Function Via WAN UPnP Function NetBIOS Communication ReportLog to TFTP Server A 2 Listed Block disable disable disable disable Manual Setup admin password disable disable disable enable disable disable 802 1x Appendix B Overview The 802 1x function restricts the connection of unauthorized stations by authenti cating each station The 802 1x function has the following advantages in security and administration Security Administration NOTES 1 The function makes authentication during station connec tion and permits only the station that has passed the authentication to communicate This function makes it difficult for an unauthorized station to get in the network Because the function dynamically distributes the WEP key the Encryption WEP key does not need to be set at each station Although several authentication methods are available the WEP key cannot be
37. Routing Center If you know their port numbers however they might be usable by registering the port numbers using Port Forwarding For details see the Forwarding section in Chapter 4 SNILOOHS318NOY TROUBLESHOOTING User s Manual Forgotten password Password to go to the Wireless Routing Center s Configuration window Set the Wireless Routing Center to the defaults Refer to the Appendix A Default values Default setting pC UserName Password Administrator Account password Password to access Internet Service Provider Call the customer support office of your Internet Service Provider Question Can the Wireless Routing Center be used with Linux TOSHIBA confirmed the operation of the Wireless Routing Center with Linux using TCP IP but offers no guarantee of operation It is outside the scope of support 5 8 Default values Appendix A Y XIGNaddy The table below lists all the Wireless Routing Center s default values Values that are not listed are blank To reset the Wireless Routing Center refer to the Load Default item in Chapter 2 The Grand Tour WAN WAWN LAN Relation Protocol LAN IP Address Subnet Mask DHCP Server Service DHCP Lease Time IP Pool Range Wireless LAN Access Point Name Network Name Channel ID Do not broadcast SSID Beacon Interval RTS Threshold Fragmentation Threshold Basic Rate Supported Rate Wireless LAN Security 802 1x WEP
38. TOSHIBA Wireless Routing Center WRC 1000 User s Manual R10UM020801 Copyright 2001 2002 by TOSHIBA Corporation All rights reserved Under the copyright laws this manual cannot be reproduced in any form without the prior written permission of TOSHIBA No patent liability is assumed with respect to the use of the information contained herein TOSHIBA Wireless Routing Center WRC 1000 User s Manual First edition August 2002 Disclaimer This manual has been validated and reviewed for accuracy The instructions and descriptions it contains are accurate for the TOSHIBA Wireless Routing Center WRC 1000 User s Manual at the time of this manual s production However succeeding devices and manuals are subject to change without notice TOSHIBA assumes no liability for damages incurred directly or indirectly from errors omissions or discrepancies between the device and the manual Trademarks Microsoft Windows NetMeeting and Windows Messenger are registered trademarks of Microsoft Corporation Ethernet is a registered trademark of Xerox Corporation is a Certification Mark of the Wireless Ethernet Compatibility cerrmiep Alliance Inc Adobe and Adobe Acrobat are registered trademarks of Adobe Systems Incorpo rated Other trademarks and registered trademarks not listed above may be used in this manual FCC information Product Name TOSHIBA Wireless Routing Center WRC 1000 Model number PA3227 FCC n
39. an automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz enabling you to use the Wireless Routing Center in almost any country region CAUTION Always use the correct AC adapter to avoid the risk of fire or damage to your Wireless Routing Center The current rating for the Wireless Routing Center is 2 0 amperes Figure 2 7 The AC adapter and power cord 2 6 Chapter 3 Setup This chapter describes how to position your Wireless Routing Center for wireless data exchange and how to connect cables The figure below shows an example of connections in a LAN and a LAN connec tion to the Internet Internet Service Home Office Provider Cable ADSL Wireless Routing Modem Center Server Desktop PC Wireless LAN Client PC Wireless LAN Client PC Wireless LAN Client PC Figure 3 1 Network connections 3 1 User s Manual Mounting The Wireless Routing Center can be used either vertically or horizontally on a desk or hung on a wall NOTES 1 Place the device close to a power outlet if possible 2 Avoid placing the device in places where people may walk on the cables Also keep it away from direct sunshine or heat sources 3 Place the device on a flat and stable stand Vertical mounting wees TO install the Wireless Routing Center upright on a desk use the stand provided as a
40. anager to open the Device Manager window 3 From the Network Adapters item double click TOSHIBA Wireless LAN Card to open the TOSHIBA Wireless LAN Card Properties dialog box 4 Ifthe message This device is working properly is shown in the item Device Status it indicates that the driver has been installed and is operating 5 3 SNILOOHS318NOY L TROUBLESHOOTING User s Manual Cause 2 Remedy Cause 3 Remedy 5 4 The settings of Wireless LAN stations are different from those of the Wireless Routing Center Make sure the following settings are the same on the Wireless LAN stations and the Wireless Routing Center SSID Network Name Basic rate not higher than the communication rate of the Wireless LAN PC cards in the Wireless LAN stations WEP mode disable 64 bits 128 bits WEP key settings correspond between devices when Encryption is enabled Access Control enable disable MAC Address of Wireless LAN PC card correctly registered if Access Control is enabled TCP IP has not been set or has been improperly set at one or more of the computers Confirm that the IP address has been correctly set Windows XP 1 Click Start point to All Programs Accessories and click Command Prompt to open the Command Prompt window Enter ipconfig and press Enter Check the values for the IP address and subnet mask IP address 192 168 10 100 192 168 10 150 Subnet Mask 255 255 25
41. art and display the selected Wireless Routing Center s Web Configura tion Page A Password input window will also be displayed If the Password input window does not appear see the section Configuration window in Chapter 5 Troubleshooting Accessing Web Configuration Page After connecting to the Wireless Routing Center you will be prompted to enter username and password Leave the username admin and enter the default password of password Connect to 192 168 10 1 A Wireless Routing Center User name admin Password eocccece Remember my password Figure 4 5 Password window After you login the Overview Configuration page of the Wireless Routing Center will be displayed From this point on the Wireless Routing Center will act as a Web server sending HTML pages forms on your request You can click the menu options at the left side to start your configuration task 4 5 User s Manual i Wireless Routing Center Microsoft Internet Explorer File Edit View Favorites Tools Help O O DAG Psa germ Sun O 8 2 E Address http 192 168 10 1f Status This page displays summary for the router status Click the button to update Update o Overview f 4 ares Bee l Configuration E WAN Byte cee SystemTime 2020729 2333408 e Wireless LAN e Filters e Forwardin lt Go NAT Rown OOO Administration System Paa ccs ee Fas MAC Address Wireless LAN Inte
42. ause 2 Remedy 5 2 If you have forgotten the local IP address reset to the defaults Refer to the Appendix A Default values Note that not only the IP address but all settings will be reset The local IP address set in the personal computer may differ from that of the Wireless Routing Center Confirm that the local IP address of the computer is in the same subnet as the local IP address of the Wireless Routing Center To confirm the local IP address of the computer follow the steps below Windows XP 2000 1 Click Start and Run Enter cmd to open the Command Prompt window WwW N Enter ipconfig and press Enter Check the values for the IP address and subnet mask IP address 192 168 10 100 192 168 10 150 Subnet Mask 255 255 255 0 Default Gateway 192 168 10 1 Windows 98 Me 1 Click Start and Run then enter winipcfg in the input box 2 In the IP Configuration window check the network adapter that you want to use A IP Configuration m E r Ethemet Adapter Information Intel 8255x based Integrated Fas 7 Intel 8255x based Integrated Fast Eth Adapter Address Toshiba Wireless LAN Card IP Address PPP Adapter oroo Subnet Mask 255 255 255 0 Default Gateway 192 168 10 1 Release Renew Release All Renew All More Info gt gt Figure 5 1 Checking Ethernet adapter information Wireless LAN 3 Check the values for the IP address and subnet mask in the w
43. click Configure Q WRC_Network Preferred networks Automatically connect to available networks in the order listed below WRC_Network Move up Move down Add Remove Properties Learn about setting up wireless network configuration Figure B 9 Wireless Network Connection Properties window B 13 User s Manual 2 Select the Authentication tab Place a check mark in the Enable network access control using IEEE 802 1x check box Select Smart Card or other Certificate in the EAP type field Click Properties 4 Wireless Network Connection Properties PS General Wireless Networks Authentication Advanced Select this option to provide authenticated network access for wired and wireless Ethemet networks Enable network access control using IEEE 802 1 EAP type Smart Card or other Certificate v C Authenticate as guest when user or computer information is unavailable Figure B 10 Authentication tab B 14 Appendix B 3 Select the Use a certificate on this computer radio button Place a check mark inthe Validate server certificate check box Select a reliable certificate authority from the Trusted root certifi cate authority combo box In this example select the certificate authority which was installed in Win dows 2000 Server Smart Card or other Certificate Properties mR When connecting O Use my smart card Use a certificate on
44. define the Filter rules based on the LAN computer s MAC address IP address or the protocol type of the data packet Each filter type is described below NOTE Based on the OSI reference model MAC Filters have higher priority than IP Filters while IP Filters have higher priority than Port Filters MAC Filters Specifies the MAC address of the LAN computer from which packets are allowed or prohibited to pass through the WAN port Up to 12 entries are allowed IP Filters Specifies the range of IP addresses of the LAN computers from which packets are allowed or prohibited to pass through the WAN port You may enter the same address in both IP Start and IP End fields to define a single IP address Up to 5 entries are allowed TCP Port Filters Allows or prohibits LAN computers in the specified IP range to use TCP based service in the specified port range through the WAN port You may enter the same address in both IP Start and IP End fields to define a single IP address Up to 12 entries are allowed For example to allow or prohibit a local computer 192 168 10 210 to use FTP service using TCP port 20 and 21 IP Start IP End Port Start Port End 192 168 10 210 192 168 10 210 20 21 UDP Port Filters Allows or prohibits LAN computers in the specified IP range to use UDP based service in the specified port range through the WAN port You may enter the same address in both IP Start and IP End fields to define a single IP address
45. distributed in some of those methods If 802 1x is enabled the following conditions apply a 802 1x disabled Wireless LAN clients CANNOT commu nicate with LAN clients connected with the Wireless Routing Center s ethernet ports b 802 1x enabled Wireless LAN clients CAN communicate with LAN clients connected with the Wireless Routing Center s ethernet ports c Wireless LAN clients CAN communicate with each other regardless of which client s 802 1x functions are enabled or disabled B 1 g XIGNAaddy User s Manual 802 1x Function This section explains the 802 1x function more specifically Required Environment a The following environment is required to use the 802 1x function a x w a a d 5 STA AP Access point this product STA Wireless LAN station The 802 1x function needs to be supported even on the station side RADIUS Abbreviation of Remote Authentication Dial In User Service This server authenticates STAs CA Abbreviation of Certificate Authority This sever issues a digital certificate This server is required to use an authentication type that is called EAP TLS Smart Card or othercertificate NOTE The above terms abbreviations are used in the subsequent explanations Authentication and Distribution of WEP Key This section explains authentication re authentication and the distribution of the WEPkey B 2 Appendix B Au
46. e The name used to identify the Access Point SSID Network Name Service Set ID It uniquely identifies the logical network domain name of your Wireless LAN The default value is WRC_Network BSSID Basic Service Set ID It is the MAC address of the Access Point It can be used to identify the AP especially when wireless stations roam among different APs which all share the same SSID 4 18 Wireless LAN Security Channel ID The radio frequency used for communication Available channels vary according to the regulations in your area Select a channel out of the available channels or use the default channel Advanced Do not broadcast SSID An AP will periodically broadcast its SSID to allow the wireless clients to recognize its presence However this creates a security hole since any wireless station with SSID set to any may associate with your AP Enabling this option is recommended in order to have your AP accept only stations whose SSID is the same as its own Beacon Interval Defines the periodic intervals at which the 802 11 Wireless LAN Access Point sends a beacon RTS Threshold Request to send threshold It specifies the packet size beyond which the AP invokes its RTS CTS mechanism Packets that exceed the specified RTS threshold trigger the RTS CTS mechanism Fragmentation Threshold It determines whether packets will be fragmented and at what size On an 802 11 wireless LAN packets that exceed the fragmentation
47. e Selection Lets you select the Web browser s encoding language English or Japanese WAN Interface Information and buttons differ according to whether the router s WAN LAN relation is DHCP Client PPPoE Client or Manual Config PPPoE Client Displays the PPPoE client information The Connect Discon nect buttons let you manually launch terminate your PPPoE session DHCP Client Displays the DHCP client information To update the IP information assigned to the router s WAN port click Release and then click Renew Manual Config Displays the WAN port information you manually specified 4 7 User s Manual Overview Configuration System Language Selection This page displays summary for the router status Click the button to update Update System System Time Firmware Version 2002 07 29 23 34 08 1 05 08 WAN Interface WAN LAN Relation NAT Routing Protocol DHCP Client MAC Address 00 90 96 2 76 f5 IP Address Subnet Mask 0 0 0 0 0 0 0 0 Default Gateway 0 0 0 0 DNS Servers _ WINS Servers Host Name LAN Interface Release MAC Address 00 90 96 2C 76 F4 IP Address Subnet Mask 192 168 10 1 255 255 255 0 DHCP Server Enabled MAC Address IP Address Expires In 00 02 2d 35 d1 df 192 168 10 102 Active DHCP Leases r 7 00 00 00 00 00 00 192 168 10 100 2 days 23 hours 28 minutes 48 seconds 29 minutes 11 seconds 00 00 39 dd 00 ee 192 168 10 101 2 days 23 hours 29 minutes
48. ects your Wireless LAN against eavesdropping WEP is disabled by default If you want to protect your data when it is transferred from one station to another you should enable this security option For security concerns we strongly recommend that you enable the WEP function To enable WEP select 64 bits or 128 bits as the encryption algorithm The higher the number of bits the greater the complexity and the security of the encryption 4 20 Wireless LAN Security Authentication Mode Authentication is a process in which the AP validates whether wireless clients are qualified to access the AP s service A wireless client must be validated before it can associate with an AP The IEEE802 11 defines two types of algorithms in authentication open and shared key With open key the authentication is done through a pseudo process accepting all kinds of requests mainly used in cases where connectivity is more important than security Shared key on the other hand utilizes WEP capability to further verify if the wireless client is authorized to share this AP s resource If the client has the wrong key or no key it will fail authentication and will not be allowed to associate with the AP If WEP is enabled Select your authentication mode Both Open or Shared Both allows the wireless client to use either authentication method The authentication type must be the same on the Access Point and wireless stations to be able to
49. ed to communicate on a wireless LAN Wireless LANs use the frequency band of 2 4 GHz divided into two or more subchannels Usable chan nels are restricted by the regulations in each country Channels 1 to 11 are usable in the United States for example D default gateway A gateway is an inter face between networks The default gateway is the one that is used general ly or when a specific gateway is not designated DHCP Dynamic Host Configuration Protocol automatically sets TCP IP network information such as an IP address in each computer accessing the Internet DNS Domain Name System is an Inter net protocol for mapping host names domain names and aliases to IP ad dresses DNS relay When a DNS client sends a request to a DNS server it does not go directly to a server instead it is routed through a DNS relay The DNS server s reply is also routed through the DNS relay which sends it to the DNS client Glossary 1 AYVSSOT GLOSSARY encryption E encryption The device allows use of data encryption compliant with the TEEE802 11 standard WEP Wired Equivalent Privacy and 128 bit WEP Data encryption protects your data from external access ESSID See network name G global IP address A global IP address is used to identify a computer directly connected to the Internet It is assigned by a public organization such as the Network Information Center H hiddenstation problem Hidden sta
50. ent If this function is enabled the AP will allow association by a client only if that client s MAC address matches an address in the Allow List To enable this function select Enable option and enter the MAC Address of the Wireless LAN card in a Wireless LAN station to be allowed access to the Wireless Routing Center A MAC address must be entered in 12 digits of hexadecimal punctuated by a colon every 2 digits MAC addresses must be separated by a comma Spaces tabs and line feed are ignored Example 11 22 33 44 55 66 aa bb cc dd ee ff RADIUS Server Wireless LAN Security Configuration This page configures the Wireless LAN Security interface 802 1x Access Control ae Figure 4 20 Wireless LAN Radius 4 22 Filters This setting is used to validate wireless stations by RADIUS servers Settings can be made for up to four RADIUS servers Enable Disable Use the radio buttons to disable or enable validation of wireless stations by RADIUS servers IP Address Set the IP address of the RADIUS server Port Set the port number of the RADIUS server Shared Secret Set the shared secret of the RADIUS server The shared secret is a password for communication between the access point and the RADIUS server Time out Set a time out value in seconds A maximum of five packets can be sent in the set interval Filters When your Wireless Routing Center operates as a rou
51. er You can manage the Wireless Routing Center through a Web browser based manager To configure the Wireless Routing Center via Web browser at least one properly configured computer must be connected to the network and reside on the same subnet as the Wireless Routing Center The Wireless Routing Center comes with the default IP address of 192 168 10 1 and subnet mask of 255 255 255 0 The DHCP Server is enabled by default You can also use the TOSHIBA WRC Finder program on the TOSHIBA Wireless Routing Center WRC 1000 Utility CD ROM to open the Wireless Routing Center s Web Configuration page NOTES 1 If data is being transmitted while you are changing settings transmission will be interrupted when you click Apply 2 The DHCP server function is enabled before the Wireless Routing Center is shipped If the LAN has other DHCP servers the DHCP server function of the Wireless Routing Center must be disabled 3 You will need Internet Explorer version 5 0 or higher 4 If your browser is set to allow you to use a Proxy on your LAN you will not be able to display the Wireless Routing Center set up page In this case follow the steps below a Open the Start menu and open the Control Panel NOILWHNDIANOD aaM b Click Network and Internet Connections c Click Internet Options d Select the Connections tab and click LAN Settings e Clear the checkbox for Use a proxy server for your LAN These settings will not apply to dial
52. erations require you to simultaneously use two or more keys We identify such operations by the key top symbols separated by a plus sign For example Ctrl C means you must hold down Ctrl and at the same time press C If three keys are used hold down the first two and at the same time press the third ABC When procedures require an action such as clicking an icon or entering text the icon s name or the text you are to type in is represented in the type face you see to the left Display ABC Names of Windows or icons or text generated by the computer that appears on its display screen is presented in the type face you see to the left Messages Messages are used in this manual to bring important information to your attention Each type of message is identified as shown below CAUTION Pay attention A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment NOTE Please read A note is a hint or advice that helps you make best use of your equipment xvi Chapter 1 Introduction Overview The Wireless Routing Center features a wireless Access Point a four port LAN switch and a WAN port which extend your existing broadband Cable ADSL connection It allows the broadband connection to be shared through either the IEEE 802 11b Access Point feature or the 10 100Base TX Ethernet switch which also eliminates the need for an additional hub or switc
53. erver on your NetWOMk eeeeeeeeeeeeeeeeeeeteeeees 4 27 Routing soiin ana REAA EREA AEA 4 29 Administration Configuration sssssssssnssenunnnnnnnnennnnnunnnunnnnnnnnnnnnnnna 4 30 System Configuration ccccssececeseeeeseeeeeeeseeeeeeeeeeseeeeeeeeeeeeeneeeeeeeas 4 32 xii Chapter 5 Troubleshooting POWO sopraanon naana tected caster cen eee ected Eth nimet n lt eeeeececescensececeeeeeenseececceseys snteeceeseeeseceecesers Configuration WiINGOW ccessccessecesseeeeeseseeeneeeees Wireless LAN scccccessseeeeeeeeensseeeeeeeeensseeeeeeeessenes Application problems c ccccccsseeeeeeeeeeseeeeeeeeenens Forgotten password sccccccssseeeeeeeeseseeeeeeeeeeeseneeeeees CQUUCSHON oc cits sscecesecceettccesetcaset ceceesuecetescecesscesteteedersadses Appendixes Appendix A Default values vii cincitsiiciciccce tances snicntivenvedewwavereddecumicads Appendix B 3 72 gt Ge Appendix C AC Power Cord and Connectors c sscssescssssseeseneees Glossary Index xiii Xiv Preface Congratulations on your purchase of the TOSHIBA Wireless Routing Center WRC 1000 The WRC 1000 provides high speed wireless or wired connection to the Internet and to a Local Area Network This manual tells how to set up and begin using your TOSHIBA Wireless Routing Center WRC 1000 herein referred to as the Wireless Routing Center Manual contents This manual is composed of five chap
54. es pore est Figure 3 10 Obtain an IP address automatically 5 If your network settings is changed you will be prompted with the System Settings Change dialog box Click Yes to restart your computer Setting up the Ethernet Wireless LAN client Checking Renew IP Address under Windows 98 ME The following steps help you verify if your network adapter gets an IP address within the DHCP IP pool range 192 168 10 100 192 168 10 150 by default of the Wireless Routing Center If not you may need to renew the IP information 1 From the Start menu click Run to open the Run dialog box 2 Enter winipcfg in the dialog box and then click OK 3 Select the Ethernet or Wireless LAN adapter from the drop down list to show the IP address If necessary click Release and then Renew to get a new IP address IP Configuration E3 m Ethernet Adapter Information 8255x based Integrated Fasihg Adapter Address 00 00 39 DD 00 EE IP Address 192 168 10 100 SubnetMask 255 255 255 0 Default Gateway 192 168 10 1 Release Renew Release All Renew All More Info gt gt Figure 3 11 Specify an IP Configuration Setting up Wireless client You can also choose to access the Wireless Routing Center via a wireless client whether for configuration purposes or sharing network resources and an Internet connection To get your wireless client connected to the Wireless Routing Center verify
55. fault gateway of the router is the IP that the Wireless Routing Center first contacts to communicate with the Internet The default is 0 0 0 0 DNS Servers Specifies the IP address of the Domain Name Server Your LAN side DHCP clients use the DNS to map a domain name to its corresponding IP address and vice versa Up to three DNS servers are allowed WINS Servers Optional for Windows Internet Names Service Enter the IP addresses of WINS servers if required Domain Name Optional Allows you to supply a host and domain name for the Wireless Routing Center 4 12 Configuration for NAT Routing Mode After you finish the WAN settings click Apply to submit your changes WAN Configuration This page configures the WAN interface General WAN LAN Relation NAT Routing Bridging Protocol DHCP Client PPPoE Client Manual Config MAC Address 00 90 96 1d 12 44 Host Name IP Address 0 0 0 0 i Subnet Mask 0 0 0 0 Default Gateway 0 0 0 0 DNS Servers 0 0 0 0 WINS Servers 0 0 0 0 ig Figure 4 12 WAN Configuration Manual Config LAN Configuration for NAT Routing Mode The Wireless Routing Center communicates with a LAN through a LAN port The LAN configuration page lets you define the private IP address and DHCP server settings over the LAN interface 1 Inthe Manual Config gt IP Address Subnet Mask field enter the IP address and subnet mask for the LAN port The default LAN port IP address is 192 16
56. g airports you are encouraged to ask for authorization to use the Wireless LAN device prior to turning on the equipment Regulatory Information The TOSHIBA Wireless Routing Center WRC 1000 must be installed and used in strict accordance with the manufacturer s instructions as described in the user documentation that comes with the product This device complies with the follow ing radio frequency and safety standards Canada Industry Canada IC This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of this device L utilisation de ce dispositif est autoris e seulement aux conditions suivantes 1 il ne doit pas produire de brouillage et 2 l utilisateur du dispositif doit tre pr t accepter tout brouillage radio lectrique re u m me si ce brouillage est susceptible de compromettre le fonctionnement du dispositif The term IC before the equipment certification number only signifies that the Industry Canada technical specifications were met Approval Number 1353A WLL030 To prevent radio interference to the licensed service this device is intended to be operated indoors and away from windows to provide maximum shielding Equip ment or its transmit antenna that is installed outdoors is subject to lice
57. h The integrated DHCP server automatically assigns IP addresses to your LAN devices and with the built in Network Address Translation NAT function your LAN is protected against outside intruders The router can also be configured to filter internal access to the Internet It is designed to provide a reliable Internet access solution for the corporate environment the small office and the home user Package contents Refer to the Quick Start Guide for the Equipment checklist If any of the items is missing contact your dealer System requirements Broadband Internet connection using Cable ADSL modem for Internet connection One computer with 10 100Base T Ethernet card and TCP IP protocol installed for initial setup Internet Explorer 5 0 or higher for Web configuration Requirement for each computer on the LAN TCP IP protocol installed 1 1 NOILONGOULN INTRODUCTION User s Manual Features WAN port features gt One 10 100 Base TX RJ 45 auto sensing and crossover Ethernet WAN port for Broadband connection Cable DSL or direct Ethernet PPPoE PPP over Ethernet Client with Keep Alive Connect On Demand Support PAP and CHAP Authentication DHCP Client MAC Address Cloning Settable and Changeable IP Address LAN port features Four RJ 45 LAN ports for 10 100Base TX auto sensing amp crossover Ethernet Switch LAN connection DHCP Server IP Address setting and c
58. hanging Router features C EE SE SEE SEE SEE SEE SEE S E G NAT Firewall Support Bridge Mode Support IP Filtering IP Forwarding Static Routing DMZ Hosting DNS Forwarding DNS Relay UPnP Support Windows Messenger for Windows XP Features Security features ASCUI HEX Format 64 128 Bit WEP Key for Wireless LAN JEEE 802 1x for Wireless LAN Allow List for Wireless LAN Supports IP packets filtering based on MAC Address IP address port number and protocol VPN Support IPSec Passthrough and PPTP Passthrough Wireless LAN features Fully compatible to IEEE 802 11b standard Direct Sequence Spread Spectrum DSSS technology Seamless roaming within Wireless LAN infrastructure Low power consumption for wireless client via efficient power management Configuration and Management features Configurable through Web Browser via WAN LAN Software Upgradeable DHCP Server function for IP distribution to local network users NTP Manual System Clock Configuration Saving Retrieving Event Logging This device has been tested by TOSHIBA in accordance with UPnP Forum Test Tools and is verified to support UPnP for Windows Messenger for Windows XP NOILONGOULN User s Manual Chapter 2 The Grand Tour This chapter identifies the various components of your Wireless Routing Center Front left and top Figure 2 1 shows the Wireless Routing Center s front left and
59. ication substitution or attachment will be the responsibility of the user FCC conditions This device complies with part 15 of the FCC Rules Operation is subject to the Following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Contact Address TOSHIBA America Information Systems Inc 9740 Irvine Boulevard Irvine California 92618 1697 Telephone 949 583 3000 EU Declaration of Conformity TOSHIBA declares that the product PA3227U PA3227E PA3227A PAWRCO001 conforms to the following Standards Supplementary Information The product complies with the requirements of the Low Voltage Directive 73 23 EEC and the EMC Directive 89 336 EEC This product is carrying the CE Mark in accordance with the related European Directives Responsible for CE Marking is TOSHIBA Europe Hammfelddamm 8 41460 Neuss Germany VCCI Class B Information COPS PAURES EREEREER VCCI OR ILBOC DFABIRRAMHRECT CORBIS KERETA ATIE eSRWELTWETA CORBMNDIUAPTLED a YZEL T A SHSoe VMSe5SHCOFCEMHVET FRA II GE TIELLY RY IRUALTHRSLY Wireless LAN information Wireless Interoperability The TOSHIBA Wireless Routing Center WRC 1000 products are designed to be interoperable with any Wireless LAN product that is based on Direct Sequence Spread Spectrum DSSS radio technology and is compliant to The IEEE 80
60. inipcfg dialog box In an ordinary small scale LAN environment the subnet mask is set to 255 255 255 0 NOTE In the case where the Wireless Routing Center s setting is default the IP address is 192 168 10 1 Subnet Mask is 255 255 255 0 If the TCP IP protocol has not been installed or if the correct IP address has not been set read the manuals for your computer and LAN card and set them accordingly Cause 3 The Configuration window might not be displayed if Proxy Server has been set Remedy Set not to use Proxy Server You can enable it later The user name and password are not accepted despite repeated entries Cause The wrong user name and password have been entered Remedy Ifthe User name and Password was changed in Administrator Account enter those values If you have forgotten them reset to the defaults Refer to the Load Default item in Chapter 2 The Grand Tour Wireless LAN There is no communication between a Wireless LAN station and other computers Cause 1 The functions of Wireless LAN stations have not been correctly installed Remedy Read the manual for your Wireless LAN PC card and check that the driver has been installed and is operating correctly If you are using a TOSHIBA Wireless LAN PC card in a computer running Windows 2000 follow the steps below 1 Click Start point to Control Panel and click System to open the dialog for System Properties 2 Click the Hardware tab then double click Device M
61. land Italy wo Josa o Countries regions that have been approved TOSHIBA Wireless Routing Center WRC 1000 Table of Contents Preface Manual contents ii icccscs cei ciee cece dete sect avs ieiee weed eadeceste i eddee edt Xv CONVENTIONS cccsccsscesseesecencee cee seeeseeeeeeeeeseensenaseaaaaaassaseaaeeaneaesesseesaes XV Abbreviation S sasccdsiessxshcdaiai aca aaivecanes aa inannesnea a UAE XV ICONS anain ani ea E E A a E vaaveboeeasseetenaeiaes oe xvi EE E EE E I E E E E EEO E xvi KEY oprao sess E xvi DISP a nace xvi MESSAGES esrara E ESSE xvi Chapter 1 Introduction VON VOW occ cn cases des cance aoaaa Ea EE Eea eeaeee Eear ee aaaea 1 1 Package contents ssssssunnneennunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnaman nnna 1 1 System requirements cccceeeceeseeeeeeeeeeeeeseeeeeesseeeeeeseeeseseeeeeeseneeeeneees 1 1 Features sarcinis suede cuenesa ediewenedvvveendoenatis 1 2 WAN port features eee eee oea 1 2 LAN port 16 ALUPOS sticccscnsiecendereh evenness EE R EA KESE 1 2 Ro ter featUreSrrrcossrasnie anaa aE EAE RA 1 2 Security featur eS zoas niaaa aiaa REE AAE aE AEEA 1 3 Wireless LAN features ccccceeceeeeeeeeeeeeeeeeeeeaaeeaaeaaecaeeeeeeeeeeeteeeness 1 3 Configuration and Management features cccceeeeeeseeeeeteeeeeenees 1 3 Chapter 2 The Grand Tour Front left and top ceeeeceeeceeeeeeeeeeeeeeeeeeeseeeneeeeeeeseeseeeeneeeseeeeeeseeneeees 2 1 Bottom and right
62. less client is not associated i Link Blinking Wireless client is associated LINK If n clients are associated it blinks n times off for 3 seconds and then repeats the blink pattern If there are more than 10 clients associated n will be 10 Wireless Green Off Wireless LAN interface is not y Ready initialized properly ACT Activity Slowly Wireless LAN interface is initialized blinking properly Quickly Transmitting receiving packets on blinking Wireless LAN interface WAN WAN Green Off Power is off or no broadband Port device is connected Status Slowly Broadband device is connected blinking Quickly Transmitting receiving packets on blinking the WAN port LAN LAN Green Off Power is off or no Ethernet device 1 4 Port is connected Status Slowly Ethernet device is connected blinking Quickly Transmitting receiving packets on blinking the LAN port 2 4 Screws for wall mount Stand A stand lets you install the Wireless Routing Center in an upright position on a desk Figure 2 5 The stand Screws for wall mount Two screws are supplied to secure the Wireless Routing Center to a wall He Figure 2 6 The two screws for wall mount THe GRAND Tour User s Manual AC adapter and power cord The AC adapter converts AC power to DC power and reduces the voltage supplied to the Wireless Routing Center It c
63. lished based on the following scenario All stations support the 802 1x function Windows XP is used The WEP key to be distributed is 128 bits The CA uses Certificate Services of Windows 2000 Server The RADIUS uses Internet Authentication Service of Windows 2000 Server Device configuration The following is the device block diagram WRC 1000 STA Windows 2000 Server Windows 2000 Server Software Windows 2000 Server is used as the OS The RADIUS uses Internet Authentica tion Service The CA uses Certificate Services WRC 1000 STA Software Windows XP is used as the OS Hardware Aradio LAN card with WEP 128 bits is used B 5 g XIaNaddy Appenpix B User s Manual CA Certificate Authority Install Certificate Service in Windows 2000 Server For details on Certificate Service refer to the online Help of Windows 2000 RADIUS server Install Internet Authentication Service in Windows 2000 Server For details on Internet Authentication Service refer to the online Help of Windows 2000 Step 1 Client setting Make client settings in the following procedure 1 2 3 4 B 6 Start Internet authentication service in Administrative Tools Select Client in the Tree window and click the right mouse button Select New Client from the menu Set Friendly name In this example WRC 1000AP is set
64. ll be sent to IP Address 192 168 10 220 not to 192 168 10 210 NOILWHNDIANOD aaM Start End IP Address Start End 20 25 192 168 10 220 20 25 20 21 192 168 10 210 20 21 If you have a Web server on your network If you enable WAN Management allow external access from the WAN port see the Administration Configuration section and want to designate another Web server on your local network perform either of the procedures below to avoid port conflicts 4 27 Wes CONFIGURATION User s Manual Option 1 In the Administration page with WAN Management enabled enter a port number other than 80 for example 1234 and reserve the number 80 for your Web server If any external host wants to access your Web management server through the WAN port it should use the address below http 204 71 200 143 i e the WAN IP address 1234 Option 2 Have WAN Management use the standard port number 80 and your Web server e g 192 168 10 4 use another port number e g 8080 In this case you need to shift the incoming HTTP request destined for local web server to port 8080 of your Web server the forwarding entry may look like this Start End IP Address Start End 8080 8080 192 168 10 4 8080 8080 With the settings above an external host trying to access your local Web server should use an address like this http 204 71 200 143 i e the WAN IP address 8080 If you do not enter the suffix 8080 the external ho
65. ly configured you may wish to save current settings The saved settings can be retrieved easily if required even after you reload factory defaults Retrieve User Configurations If you have loaded factory defaults either via the Load Default button on the back panel or via the Restore button in this group you can restore your last customized settings by clicking the Retrieve button Restore Factory Defaults To restore factory defaults click the Restore button and then wait for a few minutes as the utility prompts You will return to the System configuration page when the process is complete This feature lets you remotely reset the Wireless Routing Center Otherwise the function is the same as resetting via the Load Default button see the Back section in Chapter 2 The Grant Tour gt System Reboot This option allows to you remotely reboot the Wireless Routing Center NOTE Do not reboot the Wireless Routing Center during data transmis sion Rebooting could interrupt data communication System Configuration This page is for system Firmware Upgrade Current Firmware Version 1 05 02 Locate New Firmware Upgrade User Configurations Save Current Configurations Retrieve User Configurations Restore Factory Defaults System Reboot Figure 4 25 System Configuration 4 33 User s Manual 4 34 Chapter 5 Troubleshooting This chapter provides information on restoring your Wireless Routing Center to p
66. mple you want to route the packet destined to the sub network 192 168 100 0 255 255 255 0 to the next hop 192 168 10 10 and there are 3 routers the route is as below Network Address Subnet Mask Gateway Cost Interface 192 168 100 0 255 255 255 0 192 168 10 10 3 LAN After clicking Apply to commit your changes the new route should be added to your routing table Or you can click the Update button on the top to update the routing table Routing Configuration This page configures static routing table Click the button to update Update EKE lt ji lt lt SiS Zaz i lt j lt S z is Figure 4 23 Routing Configuration 4 29 WEB CONFIGURATION User s Manual Administration Configuration gt System Clock Network administrators may want to synchronize date and time among network devices This can be done by synchronizing the local clock to an available NTP server or manually specifying the date and time in the Wireless Routing Center for your network Option 1 Using an existing NTP server 1 Inthe Set by field enable the Network Time Protocol option 2 Inthe NTP Server field enter the IP address of the NTP server 3 Inthe Update Interval field select 1 2 or 7 days 4 In the Time Zone field select a time zone according your geographic location Option 2 Manual setting 1 Inthe Set by field enable the Manual Setup option 2 Type the date and time in their
67. n accessory 1 Align the peg on the stand with the hole in the Wireless Routing Center and fit the Wireless Routing Center into the stand SETUP Figure 3 2 Installing the Wireless Routing Center in its vertical stand 3 2 Mounting 2 Set the Wireless Routing Center upright Figure 3 3 The Wireless Routing Center s upright position in a stand Horizontal mounting Four rubber pads protect the back of the Wireless Routing Center Lay it on a flat surface with the pad side down 3 3 SETUP User s Manual Wall mounting To install the Wireless Routing Center on a wall secure it to with two screws provided with the Wireless Routing Center Figure 3 4 Mounting the Wireless Routing Center on a wall AC adapter Follow the steps below to connect the AC adapter 1 Connect the power cord to the AC adapter 2 Connect the AC adapter to the DC IN jack on the back of the Wireless Routing Center 3 Connect the power cord to an electrical outlet 100 to 240 VAC CAUTION Use the adapter supplied with the Wireless Routing Center Connecting the wrong adapter could damage the Wireless Routing Center TOSHIBA assumes no liability for any damage in such case 3 4 Connecting the Wireless Routing Center Follow the order of 1 2 3 as shown in the figure below when you connect the AC adapter Reverse the order when you disconnect dnlas Figure 3 5 C
68. nsing Pour empecher que cet appareil cause du brouillage au service faisant I object d une licence il doit Etre utilise a l interieur et devrait etre place loin des fenetres afin de fournir un ecran de blindage Maximal Si le materiel ou son antenne d emission est installe a l exterieur il doit faire l objet D une license Europe EU Declaration of Conformity This device complies with the essential requirements of the R amp TTE Directive 1999 5 EC with essential test suites as per standards EN 60950 Safety of Information Technology equipment ETS 300 328 Technical requirements for radio equipment ETS 300 826 General EMC requirements for radio equipment Belgi Belgique For outdoor usage only channel 10 2457 MHz and 11 2462 MHz is allowed For private usage outside buildings across public grounds over less than 300m no special registration with IBPT BIPT is required Registration to IBPT BIPT is required for private usage outside buildings across public grounds over more than 300m An IBPT BIPT license is required for public usage outside building For registration and license please contact IBPT BIPT Gebruik buiten gebouw alleen op kanalen 10 2457 MHz en 11 2462 MHz Voor priv gebruik buiten gebouw over publieke groud over afstand kleiner dan 300m geen registratie bij BIPT IBPT nodig voor gebruik over afstand groter dan 300m is wel registratie bij BIPT IBPT nodig Voor publiek gebruik buiten geb
69. onnecting the AC adapter Connecting the Wireless Routing Center Prior to connecting the hardware make sure to power off your Ethernet device Cable ADSL modem and Wireless Routing Center Then follow the steps below to connect the related devices CAUTION The computer must be configured properly before connect ing to a LAN Logging onto a LAN using the computer s default setting could cause a malfunction in LAN operation Check with your LAN administrator regarding set up procedures 3 5 User s Manual 2 4 3 6 Connecting your computer to the LAN port Attach one end of the Ethernet cable with RJ 45 connectors to your hub switch or a computer s Ethernet port and the other end to one of the LAN ports of your Wireless Routing Center Figure 3 6 Connecting the LAN port Connecting Cable ADSL modem to the WAN port Connect the Ethernet cable attaching to your Cable ADSL modem to the WAN port of your Wireless Routing Center Figure 3 7 Connecting the WAN port Connecting the power adapter Connect the single DC output connector of the power adapter to the power jack on the side of the Wireless Routing Center Then connect the supplied power cord to the power adapter and the other end to an AC outlet Turn on the power switch Setting up the Ethernet Wireless LAN client Setting up the Ethernet Wireless LAN client To access the Wireless Routing Center via Ethernet or wireless network you must
70. otice Declaration of Conformity Information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installa tion This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interfer ence will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help WARNING TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this TOSHIBA Wireless Routing Center or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA The correction of interference caused by such unauthorized modif
71. ouwen is licentie van BIPT IBPT verplicht Voor registratie of licentie kunt u contact opnemen met BIPT L utilisation en ext rieur est autoris sur le canal 10 2457 MHz et 11 2462 Mhz Dans le cas d une utilisation priv e ext rieur d un b timent au dessus d un espace public aucun enregistrement n est n cessaire pour une distance de moins de 300m Pour une distance sup rieure 4 300m un enregistrement aupr s de T IBPT est requise Pour une utilisation publique P ext rieur de b timents une licence de Il IBPT est requise Pour les enregistrements et licences veuillez contacter l IBPT Deutschland License required for outdoor installations Check with reseller for procedure to follow Anmeldung im Outdoor Bereich notwendig aber nicht genehmigungspflichtig Bitte mit H ndler die Vorgehensweise abstimmen France Restricted frequency band only channels 10 and 11 2457 MHz and 2462 MHz respectively may be used in France License required for every installation indoor and outdoor installations Please contact ART for procedure to follow Bande de fr quence restreinte seuls les canaux 10 11 2457 et 2462 MHz respectivement doivent tre utilis s en France Toute utilisation qu elle soit int rieure ou ext rieure est soumise autorisation Vous pouvez contacter I Autorit de R gulation des T l communiations http www art telecom fr pour la proc dure a suivre Italia
72. point to Settings and then click Network and Dial up Connections 2 Right click the Local Area Connection icon and then click Properties In the General window highlight Internet Protocol TCP IP and then click Properties 4 Enable Obtain an IP address automatically and then click OK Internet Protocol TCP IP Properties E 2 xl General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings C Use the following IP address IF address Subnet mask Default gateway Obtain DNS server address automatically mC Use the following DNS server addresses Preferred DNS server Alternate DNS server Figure 3 9 Obtain an IP address automatically Checking Renew IP Address under Windows 2000 To check if your network adapter gets an IP address within the DHCP IP pool range 192 168 10 100 192 168 10 150 by default of the Wireless Routing Center follow the related description under the Windows XP section The proce dures are the same 3 9 dnlas User s Manual For Windows 98 ME 1 Click the Start menu point to Settings and click Control Panel 2 Double click the Network icon 3 Inthe Configuration window highlight TCP IP protocol for your NIC and click Properties 4 Inthe IP Address window select Obtain an IP address automati cally Then click OK TCP IP Properti
73. rface 2001 2002 Toshiba Corporation All Rights Reserved Internet Figure 4 6 Configuration window When you make settings with the Web configuration utility fields related to a selected option will be displayed to avoid conflicting setting The utility also displays an error message if you enter an invalid value Viewing system overview and log To enable your settings After you have customized the settings click the Apply button The Wireless Routing Center will begin registering the settings You will be prompted to wait for a few seconds During this process it is important not to turn the Wireless Routing Center OFF or ON The Wireless Routing Center could be damaged APPLY Submitting Settings Committing values done Please wait for 15 Seconds Figure 4 7 Apply changes After the settings have been registered the screen will return to the previous page You can then proceed with other configuration tasks Viewing system overview and log Overview Configuration Clicking the Overview link in the Status menu will display the Overview Configuration page which shows the basic information of your Wireless Routing Center including the system WAN LAN interface and Wireless LAN interface information In addition to the general information this page contains the following elements NOILVHNDIANOD aaM Update button Click the Update button on the top to update the overall status Languag
74. roper working order if there appears to be a problem Refer also to your computer user s manual Power The Power indicator does not light when the power switch is pressed Cause Remedy No power is supplied to the Wireless Routing Center Check the connection of the power cord and AC adapter Ethernet The corresponding Ethernet indicator does not glow when an Ethernet cable is connected Cause Remedy Cause Remedy The cable is not properly connected Refer to the Setting up the Ethernet Wireless LAN client section in Chapter 3 Setup and reconnect the cable The cable is inappropriate Refer to the Setting up the Ethernet Wireless LAN client section in Chapter 3 Setup and make sure you are using the proper cable Configuration window The Configuration window does not open even if the IP address of the Wireless Routing Center is entered in the address box of the browser Cause 1 Remedy The local IP address of the Wireless Routing Center may be wrong The default local IP address is 192 168 10 1 If it has not been changed specify this address If the local IP address has been changed in LAN CONFIGURATION or if a local IP address different from the default address has been set in the Wireless Routing Center because a DHCP server other than the Wireless Routing Center is in the LAN enter the set local IP address in the address box of the browser 5 1 SNILOOHS318NOY L User s Manual C
75. ss each time you log on PPPoE Client Some ISPs use a PPPoE session to connect to their clients If this is the case you should enable this option and finish the PPPoE Client settings The WAN port of the Wireless Routing Center will be assigned a public IP address from your ISP s server Manual Config If your ISP assigns you a fixed IP address you should select this option and manually enter the IP information provided by your ISP The configuration items displayed depend on your connection type Ask your ISP which option applies to you and obtain the information you need for correct configuration After you have done so proceed with the following sections WAN Configuration for NAT Routing Mode Click WAN in the configuration menu to enter the WAN Configuration page and carry out the procedures below Part 1 Configuring general settings 1 Inthe WAN LAN Relation field select the NAT Routing option This option allows the Wireless Routing Center to act as a router and use the built in NAT function to translate your multiple private IP addresses to a single public IP address However only outgoing requests are allowed to pass through the Wireless Routing Center unless you specify otherwise Outside users cannot see your private local IP addresses This protects your home or business network from outside intruders 2 Inthe Protocol field select a protocol type according to the connection type offered by your ISP 4 9
76. st s packets will contain the standard port number 80 and the router will not forward the packets since no forwarding entry matches As a result if a WAN computer tries to access the LAN s WEB server it will be routed to the WRC 1000 Web configuration page instead Forwarding Configuration This page configures port forwarding from WAN interface to LAN interface Requests to the specified WAN port range will be forwarded to the port range of the LAN machine DMZ IP Address Start End P Address Start End TCP Port Forwards 7 i g More Start End P Address Start End UDP Port Forwards E i E l More Figure 4 22 Forwarding Configuration 4 28 Routing Routing If your Wireless Routing Center is connected to more than one router or your network is composed of multiple subnets you may need to set up a static route to determines the data transmitting route The page displays the routing table of the Wireless Routing Center and allows you to set up a maximum of 8 static routing rules To add a new static IP route enter these fields Network Address The destination IP address of the network where data packets are to be sent Subnet Mask The subnet mask of the destination IP address Gateway The IP address of the gateway where data packets are to be sent Cost Hop Count The number of hops number of relay routers to go through Interface The interface through which data is forwarded to the next hop For exa
77. tential for human contact during normal operation is minimized When using this device a certain separation distance between antenna and nearby persons has to be kept to ensure RF exposure compliance The distance between the antennas and the user should not less than 20cm Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information Using this equipment in Japan In Japan the frequency bandwidth of 2 400 2 483 5MHz for second generation low power data communication systems such as this equipment overlaps that of mobile object identification systems premises radio station and specified low power radio station 1 Sticker Please put the following sticker on devices incorporating this product In the frequency bandwidth of this equipment industrial device scientific device medical device like microwave oven licensed premises radio station and non licensed specified low power radio station for mobile object identification system RF ID that is used in product line of factories Other Radio Stations are used Please make sure before using this equipment that no Other Radio Stations are used in the neighborhood In case that RF interference occurs to Other Radio Stations from this equipment please change promptly the frequency for use place to use or stop emitting Radio Please contact TOSHIBA Direct PC if you have a problem such as interference from this eq
78. ter the built in NAT function provides your LAN with Internet access via the single public IP of the WAN port That means all network devices are allowed to access the Internet Therefore network security becomes an important issue and system administrators may need to build access controls to protect the network Filters serve as a basic security measure for your network When the filter function is enabled the Wireless Routing Center inspects all data packets received from the LAN and determines if packets are allowed to pass through the WAN port Whether a packet is allowed to pass through depends on whether it matches your filter rules and whether your filter type is Listed Pass or Listed Block Specifying IP Filter Rules NOILWHNDIINOD aaM NOTE If you make a mistake in Filter Rules you might not be able to access the Internet If you are going to specify your filter rules follow the procedures below 1 Inthe General gt Filter Type field select the action Listed Block or Listed Pass to be performed on the IP packets matching your filter rules 2 Inthe four filter types select whether to enable or disable each filter 3 Ifa filter is enabled enter the criteria in the fields provided Click More to add more criteria if required See the next section for more information 4 Click Apply to register your changes 4 23 WEB CONFIGURATION User s Manual Filter Types When setting up filter rules you can
79. ters three appendixes and an index Chapter 1 Introduction is an overview of the device s features and capabilities Chapter 2 The Grand Tour describes devices and components Chapter 3 Setup tells how to connect and setup your LAN devices Chapter 4 Web Configuration tells how to configure the Wireless Routing Center via Web browser Chapter 5 Troubleshooting suggests courses of action if the device doesn t seem to be working properly Appendix A lists all default settings Appendix B describes the 802 1x function Appendix C describes the power cord and connectors The Index quickly directs you to the information contained in this manual Conventions This manual uses the following formats to describe identify and highlight terms and operating procedures Abbreviations On first appearance and whenever necessary for clarity abbreviations are enclosed in parentheses following their definition For example Read Only Memory ROM Acronyms are also defined in the Glossary XV User s Manual Icons Icons identify ports dials and other parts of your Wireless Routing Center The indicator panel also uses icons to identify the components it is providing informa tion on Keys The keyboard keys are used in the text to describe many computer operations A distinctive typeface identifies the key top symbols as they appear on the keyboard For example Enter identifies the Enter key Key operation Some op
80. thentication Authentication starts when a radio LAN station connects to the access point When the station connects the access point issues a request to start authentica tion for that station Although the station that has received the request starts the authentication procedure the access point transfers all messages related to the authentication to the RADIUS server That is the authentication itself is performed between the station and RADIUS server While the authentication procedure is performed the station cannot join the network When the station passes the authentication the RADIUS server reports to the access point The access point will then allow the station to join the network The following shows the authentication procedure successful example Authentication procedure successful example RADIUS i 1 The station connects to the access point 2 A request to start authentication is sent from the access point to the station The authentication procedure is performed between the station and RADIUS server 4 The RADIUS server reports to the access point that the station has passed the authentication 5 The access point reports to the station that the station has passed the authentication g XIGNAaddy Appenpix B User s Manual The access point permits the station to communicate At this point the WEP key can be distributed Whether the WEP key can be dis
81. this computer Validate server certificate C Connect only if server name ends with Trusted root certificate authority TEST CA v C Use a different user name for the connection Figure B 11 Properties window Check items Check whether authentication ended successfully as follows Check the Windows 2000 Server system log for source name IAS Check the status of the radio LAN adaptor on the Windows XP network control panel B 15 User s Manual Appendix C AC Power Cord and Connectors The power cord s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country region in which it is used All cords must meet the following specifications Length Wire size Current rating Voltagerating Certification agencies U S and Canada Europe Austria Belgium France United Kingdom Australia Japan Minimum 1 8 meters 5 9 ft Minimum0 75 mm Minimum 2 5 amperes 125 or250 VAC depending on country region s power standards UL listed and CSA certified No 18 AWG Type SVT or SPT 2 two conductor OVE Italy IMQ CEBEC The Netherlands KEMA UTE Germany VDE BSI AS DENANHO In Europe power cords must be VDE type HOS VVH2 F and two conductor For the United States and Canada plug configuration must be a 2 15P 250 V or 1 15P 125 V as designated in the U S National Electrical code
82. threshold are fragmented into smaller units suitable for the circuit size On the other hand packets smaller than the wireless station s should be used to connect to your Access Point Basic Rate Specifies the basic rate the wireless stations should use to connect to your Access Point Supported Rate Allows the AP to automatically adjust the transfer speed to the rates you specified Wireless LAN Security The Wireless Routing Center provides three types of wireless communication security JEEE802 1x WEP Wired Equivalent Privacy Access Control The combination of these three features provides a high level of security for Wireless LAN transmissions For details of IEEE802 1x functions refer to Appendix B 802 x NOILWHNDIANOD aaM User s Manual Wireless LAN Security Configuration This page configures the Wireless LAN Security interface Cancel Figure 4 19 Wireless LAN Security 802 1x 802 1x Specify whether to use the 802 1x function The options are Not Used and Used Wep Key Distribution Specify whether to dynamically distribute the WEP key This radio button will appear when the 802 1x function is used Key Length Specify the length of the WEP key to be distributed This radio button will appear when the 802 1x function is used WEP WEP Mode WEP Wired Equivalent Privacy is an authentication algorithm that encrypts your data and prot
83. tivity log go to Status gt Log Activity Log is displayed with a maximum of 32 entries Click the Update button to refresh the log with newly reported data The log types are defined below Category Possible reason 1 Blocked packets from WAN side by DoS Deny of Service protection mechanism 2 Blocked packets from LAN side by MAC IP TCP UDP filter Forwarding This page allows you to configure the Forwarding and DMZ De Militarized Zone features Unlike Filter which governs outgoing traffic Forwarding is used to provide external access to your local computers This is commonly used when you have publicly accessible virtual servers on your local network By default forwarding entry is empty and any external access to your LAN is blocked Once you define a forwarding entry incoming packets identified by port number that match your Forwarding criteria will be forwarded to the port range of the specified local computer Otherwise packets are blocked Forwarding protects your network from hazardous packets However if you designate a DMZ sever incoming packets that do not match the forwarding criteria will be redirected to the DMZ IP address Forwarding has a higher priority than DMZ NOTE The wrong Port Forwarding setting could allow unauthorized access to the LAN Please be careful when you make Port Forwarding settings Setting Up Forwarding Entries To set up your forwarding entries enter the following fields DMZ
84. tributed depends on the authentication type 6 The station can joint the network Authentication type Several types of authentication are prepared The radio LAN station and RADIUS server need to predetermine which type of authentication to use mutually If different types of authentication are set the authentication procedure cannot be performed and the authentication of the station fails Whether the WEP key can be distributed depends on the authentication type The following lists the typical types of authentication Name Description MD5 Challenge Authentication method using the user name and password In this type of authentication the WEP key cannot be distributed EAP TLS Authentication method using a digital certificate It may be represented by Smart Card or other certificate To use this type of authentication the certificate needs to be obtained from the CA and stored in each station In this type of authentication the WEP key can be distrib uted Distribution of WEP key When authentication ends successfully the access point distributes the WEP key to the station Whether the WEP key can be distributed depends on the authenti cation type The WEP key is created at random by the access point B 4 Appendix B Configuration Example This section explains how to establish the 802 1x environment giving specific examples Configuration Example The environment is estab
85. uest a certificate for your web browser e mail client or other secure program Once you acquire a certificate you will be able to securely identify yourself to other people over the web sign your e mail messages encrypt your e mail messages and more depending upon the type of certificate you request Select atask ORetrieve the CA certificate or certificate revocation list Request a certificate Check on a pending certificate Internet Figure B 8 Certificate Installation NOTES 1 To issue a certificate from the certificate authority and install it Certificate Service Web Enrollment Support needs to have been installed in the certificate authority B 12 Appendix B 2 The above example issues and installs a certificate through the network You can also download the certificate into a file and install it from media such as a floppy disk For more information refer to the online Help of the certificate authority Step 2 Setting the 802 1x function in the Wireless LAN station Next set the 802 1x function The following procedure is to enable the 802 1x function The other settings for the radio LAN network are omitted For details on each item refer to the online Help of Windows XP 1 Open Wireless Network Connection Properties 4 Wireless Network Connection Properties PIS General Wireless Networks Authentication Advanced Available networks To connect to an available network
86. uipment to Other Radio Stations 2 Indication The indication shown below appears on this equipment 1 2 3 2 4 DS4 oe 4 1 2 4 This equipment uses a frequency of 2 4 GHz 2 DS This equipment uses DS SS modulation 3 4 The interference range of this equipment is less than 40 m 4 mm am mam This equipment uses a frequency bandwidth from 2 400 MHz to 2 483 5 MHz It is possible to avoid the band of mobile object identification systems 3 TOSHIBA Direct PC Monday Friday 10 00 17 00 Toll Free Tel 0120 13 1100 Direct Dial 03 3457 5916 FAX 03 5444 9450 Device Authorization This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval and it belongs to the device class of radio equipment of low power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan The Name of the radio equipment WLL032 TELECOM ENGINEERING CENTER Approval Number 0 1INYDA1271 01GZA1144 The following restrictions apply Do not disassemble or modify the device Donot install the embedded wireless module into other device Approved Countries regions for use This equipment is approved to the radio standard by the countries regions listed in the table below CAUTION Do not use this equipment except in the countries regions in the following table France Germany Greece Iceland Ire
87. up or VPN connections f Click OK 4 1 WEB CONFIGURATION User s Manual Accessing Web Configuration Page NOTE Connect the computer running WRC Finder to the Wireless Routing Center by cable You should not use a wireless connection The computer running WRC Finder must be on the same subnet as the Wireless Routing Center in order to display the Wireless Routing Centers in a list If you want to change a setting in a Wireless Routing Center double click the Wireless Routing Center you want to change Your Web browser will start and display that Wireless Routing Center s Web Confirmation Page 1 NOTE If you know the IP address of the Wireless Routing Center you want to set you can enter http 2222222 in your Web browser and go directly to the Web Confirmation Page specifies the IP address of the Wireless Routing Center The default value is 192 168 10 1 about blank Microsoft Internet Explorer File Edit View Favorites Tools Help x a Ay Search sie Favorites Media Kiz lt A 2 Address http 192 168 10 1 Figure 4 1 Web Browser Follow the steps below to start TOSHIBA WRC Finder 1 Load the TOSHIBA Wireless Routing Center WRC 1000 Utility CD ROM in the set up computer 2 Use Windows Explorer to locate and copy the file WRC_FIND exe to the computer s hard disk Accessing Web Configuration Page 3 Double click the copied file WRC_FIND exe to start the WRC Finder
88. verview Configuration ccccccccceeeeeeeeeeeeeeeeeeaeeeeeeaeeeeseeeeeessaaeesseas 4 7 IMG F LOG E A A E E A T E 4 8 Configuration for NAT Routing Mode ssssssnnnnnnnnunnnenunnnnnnnnnnnnnnn 4 9 WAN Configuration for NAT Routing Mode n se 4 9 LAN Configuration for NAT Routing Mode cccccesseeeseeeteneees 4 13 Configuration for Bridge Mode ccsseccseeeeeeeseeeseeeeeseneeeneeees 4 16 Wireless LAN Configuration ssssssssennneunnnnunnnnnnnnnnunnnnnnnnnnnnnnnnnnna 4 18 BASIC siese S E vn pdedliinesenedsaeeees cane 4 18 POVAN OO ssiccctstactsdenccctede wyccteciiasindiactissensterceteitenitnectieds puccettiasieas 4 19 Wireless LAN Security ccesscceeeeeeeeeeeeeeseneeeeneeeeeesneeeeenseneeeneees 4 19 O28 NK acediinics ce sapDbahices E E a O 4 20 WEP marenea aai aA A aa EAE S raaa EEEE AESA 4 20 ACCESS Control sesinin e aa 4 22 RADIUS Sefvet sccecccettuctancecpeavasstitcevecel ba becdeneens se dieceledintiacueee chansabters 4 22 FANON Sass deceteseeeece cei reset ide Sevetsentwuc decid vsenta deed sheaubnueusssuvseucoddcsiuessbeoudeeev sy 4 23 Specifying IP Filter Rules 0 ee eeeceecceeeeeeeeeeeeeeneeeeeeaeeeeeeeeeeeeeeeees 4 23 Filter TYPOS ici vee tienes ies een aiviideenoatien lineal EAA 4 24 Forwarding scecieeceecsccceecinececteeseannticteecuduactecierennnsuscdiereuaueccwedewetns 4 26 Setting Up Forwarding Entries 0 cccccceeeeeseeeeeceeeeseneeeeenaeeeseneees 4 26 If you have a Web s
89. vides four RJ 45 ports for connection to a hub switch or NIC equipped computer in your network The LAN ports support Auto MDIX feature which eliminates the need for crossover cables One RJ 45 port provides connection for a Cable ADSL modem The WAN port also supports Auto MDIX which eliminates the need for crossover cables To reset the Wireless Routing Center to factory defaults insert a straightened paper clip into the Load Default hole to press the button Keep pressing and turn the Wireless Routing Center off and on Wait for at least five seconds before you release the button Then wait for the Wireless Routing Center to finish booting If you want to restore your customized settings after loading defaults refer to the System Configuration tion Indicators Front Panel section in Chapter 4 Web Configuration for more informa The following illustration shows the front panel of the Wireless Routing Center o Power p LAN LINK ACT WAN 1 2 3 4 Wire _ess LAN WAN LAN 1 2 3 4 Figure 2 4 The indicators HNO GNVHS IHL THE GRAND Tour User s Manual LED Indicators The Wireless Routing Center is equipped with eight LEDs on the front panel as described in the table below Table 2 1 Indicator conditions LEDs Function Color Status Description Power Green Off No power is supplied to the unit 9 Solid Power is supplied to the unit Wireless Green Off l Wire

WRC-1000 Wireless Routing Center

Contents

Download Pdf Manuals

Related Search

Related Contents