Home

Release Notes for V3.2.0.1

1. gt PENTAIR eTA IMPORTANT As part of the upgrade process the ENV VAR settings will be restored to factory default Please make sure to take note on the ENV VAR settings so they can be restored at the end of the upgrade To display the current settings type shmm500 printenv The default settings are listed in the chapter Configuration Settings Step 5 If your ShMM 500 module has the net command defined you can use this command to boot the upgrade kernel and RFS as follows shmm500 run net If it does not you can set the system variables step by step and start the upgrade process setenv bootargs bootargs root dev ram rw console ttyS0 115200 lt enter gt setenv reliable upgrade y lt enter gt tftp 80400000 sentry kernel lt enter gt tftp 81200000 sentry rfs lt enter gt bootm 80400000 81200000 lt enter gt The upgrade kernel and RFS will boot and automatically start the upgrade process This procedure may take several minutes The ShMM will reboot automatically after the upgrade is complete Step 6 Verification of the upgrade After bootup of the system log in as root with empty password shmm500 login root Password To verify the successful upgrade you can verify the version that you are running with the version command version Current Boot mage Name 63998 08175 U Boot 1 1 4 Created Tue Oct 22 13 01 18 2013 mage Type MIPS Linux Firmware uncompressed Data Size 189360 Byt
2. etc rc Preserved ssh_host_dsa_key in etc ssh etc rc Preserved ssh_host_rsa_key in etc ssh etc rc Mounted dev mtdblockl to etc etc rce Setting timezone to UTC etc rce Placed var tmp to ram disk etc rce Setting hostname shmm500 etc re Started syslogd and klogd etc rce Calling etc rc acb HPDL etc readhwaddr Board Hardware Address 0x10 etc netconfig etc hosts updated with shmm500 192 168 0 22 entry etc netconfig Updating etc profile sentry with IP settings etc netconfig Starting bin inetd etc netconfig Starting time synchronization script etc rc acb HPDL Image Name 63998 08175 RFS 3 2 0 1 etc rc acb HPDL Updating etc profile sentry with specific settings etc rc acb HPDL Starting snmpd etc rc acb HPDL Starting httpd etc rc acb HPDL Starting Shelf Manager for carrier type ACB etc rc acb HPDL Command line shelfman sf etc rc acb HPDL Strobing the reliable upgrade WDT lt gt 01 48 33 729 141 Pigeon Point Shelf Manager ver 3 2 0 1 Built on Sep 5 2013 08 13 49 lt gt 01 48 33 790 141 Lock log print buffer at 0x10070010 lt gt 01 48 33 792 141 Pthread lock log print buffer at 0x10074860 lt I gt 01 48 33 802 141 Reading configuration file etc shelfman conf shmm500 login root Password Step 3 Verification of the upgrade After bootup of the system log in as root with empty password shmm500 login root Password To veri
3. 0x00 Board ShMM 500 S N 08026624 DRAM Samsung K4S511633F 128 MB Flash 64 MB In serial Out serial Err serial ADM1060 configuration version 1 5 Net AulX00 ETHERNET Hit any key to stop autoboot 0 Booting image at be080000 mage Name 63998 08175 Kernel Linux 2 4 26 Created 2013 10 22 13 01 18 UTC mage Type MIPS Linux Kernel Image gzip compressed Data Size 879654 Bytes 859 kB Load Address 80100000 Entry Point 802d4040 Verifying Checksum OK Uncompressing Kernel Image OK Loading Ramdisk Image at be440000 mage Name 63998 08175 RES 3 2 0 1 Created 2013 10 22 13 01 18 UTC mage Type MIPS Linux RAMDisk Image gzip compressed Data Size 3918820 Bytes 3 7 MB Load Address 00000000 Entry Point 00000000 Verifying Checksum OK Starting kernel init started BusyBox v1 16 2 2013 09 05 08 20 41 PDT etc rce Mounting filesystems etc rce Mounted proc etc rc Mounted dev pts etc rc Mounted dev mtdblock10 to var upgrade etc rc Mounted tmp etc rce Checking the reliable upgrade watchdog timer inactive etc rc Mounted dev mtdblock0O to var etc rc Mounted dev mtdblockl to etc etc re Setting timezone to UTC etc rc Placed var tmp to ram disk etc rce Setting hostname shmm500 etc rce Started syslogd and klogd etc rce Calling etc rc acb HPDL etc readhwaddr Board Hardware Address 0x10 etc netconfig etc hosts has valid shmm500
4. cecccceeeeeeeeeeeeeeeeeee eee eeeeeaaaaaeeeeeeeeetegenaaaaeeeeeeeeeneaaa 21 5 Resetting the Shelf Manager configuration to the default ValUCS ssseseeeeseeeeeeeees 23 6 Configuring Ethernet Port Bonding on the Shelf Managet cccecccesseeeeeeeeeeeeeeeeeeeeees 26 7 Firmware part number 63998 08175 configuration files cceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaaees 27 8 Revision DSTO sie cect acie gee Seen ceasten eee oe tenwee tana yan Scaoni lt ancaiwee ss aonuenepacaveassacutaasesaueaceansutatos 29 Release Note Pentair Schroff Firmware part number 63998 08175 3 34 October 22 2013 gt PENTAIR eTA 1 Pentair Schroff shelf manager versions The table below shows the Pentair Schroff shelf manager versions please identify your shelf manager type You will need the corresponding RC2 variable later in the upgrade process Photo Type RC2 variable ACB V rc acb HPDL The part number of the ACB V shelf manager is on the label at the rear side of the shelf manager see photo below eas Radial IPMB version p n 21596 292 Pace SHELFIANAGER Bused IPMB version p n 21596 291 cai Serial Fiuriiber Rev ACB IV rc acb HPDL Note If you have this shelf manager in your Zephyr or Ventus shelf please follow the special upgrade instructions The part number of the ACB IV shelf manager is on the label at the rear side of the shelf manager see photo below Sei Radial IPMB vers
5. 184 92 kB 0 18 MB Load Address 0x9FC00000 Entry Point 0x00000000 Current Kernel mage Name 63998 08175 Kernel Linux 2 4 26 Created Tue Oct 22 13 01 18 2013 mage Type MIPS Linux Kernel Image gzip compressed Data Size 879654 Bytes 859 04 kB 0 84 MB Load Address 0x80100000 Entry Point 0x802D4040 Current RFS Image Name 63998 08175 RFS 3 2 0 1 Created Tue Oct 22 13 01 18 2013 Image Type MIPS Linux RAMDisk Image gzip compressed Data Size 3918820 Bytes 3826 97 kB 3 74 MB Load Address 0x00000000 Entry Point 0x00000000 Alternate section not printed Pigeon Point Shelf Manager Command Line Interpreter Pigeon Point Shelf Manager Command Line Interpreter Pigeon Point Shelf Manager ver 3 2 0 1 Pigeon Point and the stylized lighthouse logo are trademarks of Pigeon Point Systems Copyright c 2002 2013 Pigeon Point Systems All rights reserved Build date time Sep 5 2013 08 13 49 Carrier HPDL ACB Carrier subtype 0 subversion 0 Cooling Management Library libcooling acb so Version 3 2 0 1 Carrier Product ID 21596291 Chassis Product ID 11596160 2 Correct RC2 file cat var log messages grep Calling etc rc acb HPDL Jan 22 17 22 13 shmm500 user info etc re Calling etc rc acb HPDL Check with the appropriate setting for your shelf manager from the table Pentair Schroff shelf manager versions at the top of this document Release Note Pentair Schroff Firmware part
6. 192 168 0 22 entry etc netconfig Updating etc profile sentry with IP settings etc netconfig Starting bin inetd etc netconfig Starting time synchronization script etc rc acb HPDL Image Name 63998 08175 RFS 3 2 0 1 Release Note Pentair Schroff Firmware part number 63998 08175 24 34 October 22 2013 Schroff gt PENTAIR Atta etc re etc re etc re etc re etc re lt gt 03 14 12 688 lt gt 03 14 12 699 lt gt 03 14 12 70 lt I gt 03 14 12 71 shmm500 acb HPDL acb HPDL acb HPDL acb HPDL acb HPDL Updating etc profile sentry with specific settings Starting snmpd Starting httpd Starting Shelf Manager for carrier type ACB Command line shelfman sf 118 Pigeon Point Shelf Manager ver 3 2 0 1 Built on Sep 5 2013 08 13 49 118 Lock log print buffer at 0x10070010 118 Pthread lock log print buffer at 0x10074860 118 Reading configuration file etc shelfman conf login root Password Release Note Pentair Schroff Firmware part number 63998 08175 25 34 October 22 2013 gt PENTAIR eTA 6 Configuring Ethernet Port Bonding on the Shelf Manager In the default configuration the shelf manager will assign the RMCP IP address from the shelf FRU data to port 1 ethO on the active shelf manager If the active shelf manager fails or the Ethernet link to port 1 fails a switchover will occur and the RMCP address will be assigned to the port 1 o
7. 80400000 off 0000 count 6144 done shmm500 reset U Boot 1 1 4 Oct 22 2013 09 00 47 CPU Aul550 324 MHz id 0x02 rev 0x00 Board ShMM 500 S N 08026624 DRAM Samsung K4S511633F 128 MB Flash 64 MB xxx Warning bad CRC using default environment In serial Out serial Err serial ADM1060 configuration version 1 5 Net AulX00 ETHERNET Hit any key to stop autoboot 0 shmm500 save Saving Environment to EEPROM shmm500 save Saving Environment to EEPROM shmm500 reset Use the Linux getenv command to display the U boot rc2 environment variable setting getenv rc2 rce2 etc rce acb HPDL Release Note Pentair Schroff Firmware part number 63998 08175 23 34 October 22 2013 gt PENTAIR eTA The shelf manager application stores its configuration files in the etc and var directories You can modify these settings by editing the configuration files If you modify the configuration files incorrectly you can use this procedure to set the configuration files back to their default values 1 Use the setenv command to change the U boot environment variable flash_reset to y 2 Reboot the shelf manager with the reboot command setenv flash_reset y reboot The system is going down NOW Sending SIGTERM to all processes Please stand by while rebooting the system Resetting Integrated Peripherals U Boot 1 1 4 Oct 22 2013 09 00 47 CPU Aul550 324 MHz id 0x02 rev
8. DHCP server additional addresses returned by the DHCP server were not used The NTP client can use up to six separate addresses which may be important in some use cases In the Get Sensor Reading response reserved flags were not set to 1 as the IPMI specification requires The clia utility could crash if the CARRIER environment variable was not defined Startup script etc rc common was corrected to start hpiSubagent only after openhpid is started Both these utilities are now started only if U Boot variable openhpi is set to y DHCP client did not bring up network interface before using it Release Note Pentair Schroff Firmware part number 63998 08175 33 34 October 22 2013 gt PENTAIR eTA For previous releases please see the Pigeon Point firmware release notes Release Note Pentair Schroff Firmware part number 63998 08175 34 34 October 22 2013
9. FRU ID files included in firmware version 63998 08175 Chassis P N FRU File name Chassis description 11596 007 11596007HBBIN bin 2slot push pull cooling bused IPMB node node AC 11596 010 11596010HBBIN bin Sslot push cooling bused IPMB Triple Repl Mesh DC 11596 012 11596012HBBIN bin Sslot push cooling bused IPMB Triple Repl Mesh DC 11596 090 11596090HEBIN bin 2slot push pull cooling bused IPMB Hub Hub DC 11596 100 11596100HBBIN bin 14slot pull cooling bused IPMB Dual Star DC 11596 101 11596101HBBIN bin 14slot pull cooling rad IPMB Dual Star DC 11596 102 11596102HBBIN bin 14slot pull cooling bused IPMB Full Mesh DC Release Note Pentair Schroff Firmware part number 63998 08175 6 34 October 22 2013 gt PENTAIR 11596 103 11596 107 11596 150 11596 151 11596 152 11596 153 11596 160 11596 161 11596 300 11596 301 11596 302 11596 303 11990 060 11990 100 11990 101 11990 102 11990 103 11990 200 11990 600 11990 601 11990 604 11990 605 Release Note Pentair Schroff Firmware part number 63998 08175 7 34 11596103HBBIN bin 11596107HBBIN bin 11596150HEBIN bin 11596151HEBIN bin 11596152HDBIN bin 11596153HDBIN bin 11596160HDBIN bin 11596161HDBIN bin 11596300HCBIN bin 11596301HBBIN bin 11596302HBBIN bin 11596303HBBIN bin 11990060HABIN bin 11990100HCBIN bin 11990101HCBIN bin 11990102HABIN bin 11990103HABIN bin 11990200HABIN bin 11990600HABIN bin 11990601 HABIN bin 11990604HABIN bin 11990605HABI
10. Shelf Manager Command Line Interpreter Pigeon Point Shelf Manager ver 3 2 0 1 Pigeon Point and the stylized lighthouse logo are trademarks of Pigeon Point Systems Copyright c 2002 2013 Pigeon Point Systems All rights reserved Build date time Sep 5 2013 08 13 49 Carrier HPDL ACB Carrier subtype 0 subversion 0 Cooling Management Library libcooling acb so Version 3 2 0 1 Carrier Product ID 21596291 Chassis Product ID 11596160 In case the new firmware version appears in the alternate section and the old version in the current section the watchdog timer has expired and reset the firmware version to the version before the upgrade You can use the command rupgrade_tool sR to flip the firmware version the shelf manager will boot For the necessary FRU File update and additional settings please proceed to the chapter Updating FRU data files Release Note Pentair Schroff Firmware part number 63998 08175 14 34 October 22 2013 gt PENTAIR eTA 3 2 TFTP Upgrade Procedure An overview of the procedure is as follows Download the 63998 08175 rfs and 63998 08175 kernel images and place them on your network reachable TFTP server The 63998 08175 rfs image includes the u boot bin sentry shmm500 kernel and sentry shmm500 rfs images inside this special boot image TFTP boot the upgrade kernel and RFS images on your ShMM 500 Once booted the upgrade script will automatically update your SAMM 500 us
11. Shelf Manager access only to the FRU information of the corresponding physical Shelf Manager FRU and its subsidiary FRUs if any with read only access to the cached copy of the Shelf FRU Information IPMC 20h FRU 254 2 8 0 2 New and Changed Features for This Release 1 This release is based on an update of Monterey Linux that includes the following specific change 1 ShMM 500 ShMM 1500 The supported Common Flash Interface CFI Extended Query Table minor version number has been increased to 9 2 The directory tmp is now mounted at startup via the file system tmpfs which allows allocating up to the half of the physical memory for temporary files This can be useful for IntegralHP FUMI upgrades that need to store the Shelf Manager firmware image in a temporary directory during the upgrade and fail if there is not enough space available there 3 Support has been added for four levels of versioning in the headers of RFS images that are used for the Shelf Manager upgrades including FUMI based Shelf Manager upgrades via IntegralHPI Bug Fixes 1 Test results returned by the Diagnostic Initiator for the ShMM diagnostics could have random contents in some cases 2 The HPDL Driver for generic PMBus devices could incorrectly set parameters supplied via the IPMI settable sensor interface to the device if these parameters were represented in PMBus Linear format on the device 2 8 0 1 Bug Fixes 1 When the configuration variable NO_MO_M1
12. U Boot 1 1 4 Oct 22 2013 09 00 47 CPU Aul550 324 MHz id 0x02 rev 0x00 Board ShMM 500 S N 08026624 DRAM Samsung K4S511633F 128 MB Flash 64 MB In serial Out serial Err serial ADM1060 configuration version 1 5 Net Au1lX00 ETHERNET Hit any key to stop autoboot 0 Booting image at be080000 mage Name 63998 08175 Kernel Linux 2 4 26 Created 2013 10 22 13 01 18 UTC mage Type MIPS Linux Kernel Image gzip compressed Data Size 879654 Bytes 859 kB Load Address 80100000 Entry Point 802d4040 Verifying Checksum OK Uncompressing Kernel Image OK Loading Ramdisk Image at be440000 mage Name 63998 08175 RFS 3 2 0 1 Created 2013 10 22 13 01 18 UTC mage Type MIPS Linux RAMDisk Image gzip compressed Data Size 3918820 Bytes 3 7 MB Load Address 00000000 Entry Point 00000000 Verifying Checksum OK Starting kernel init started BusyBox v1 16 2 2013 09 05 08 20 41 PDT Release Note Pentair Schroff Firmware part number 63998 08175 12 34 October 22 2013 gt PENTAIR eTA etc rc Mounting filesystems etc rce Mounted proc etc rce Mounted dev pts etc re Mounted dev mtdblock10 to var upgrade etc rc Mounted tmp etc rce Checking the reliable upgrade watchdog timer activated etc rc Mounted dev mtdblock0O to var etc rce Strobing the reliable upgrade WDT etc rce dev mtdblockl appears to be empty restoring from factory etc
13. configuration digest file This is done to avoid unnecessary writes to the etc filesystem that may reduce free space 26 In case of multiple E Keying link choices with different extensions the c1 ia utility could display the list of enabled links incorrectly 27 Theclia sensordata t command displayed sensors in the Initial Update state 28 The clia terminate command produced an error message if an alias Ethernet interface was configured as an RMCP capable interface 2 8 2 1 New and Changed Features for This Release Added the setseltime script that will set the SEL time in an ATCA board from the Shelf Manger s time 2 8 2 New and Changed Features for This Release 1 This release is based on an update of Monterey Linux that includes the following specific changes 2 Abugin the JFFS2 file system driver that could cause corruption of data written to a file on a flash partition which is almost full has been fixed 3 Counters for the number of bytes received or transmitted over IPMB are now available to user mode programs and interactive users via the following files in the directory proc sys dev ipmb in text format ipmb_receive_bytes_a ipmb_receive_bytes_b ipmb_transmit_bytes_a ipmb_transmit_bytes_b 4 Support for using secure shell identity file in SCP mode has been added to the rupgrade_tool utility The identity file name can be specified using the proto scp serverip dir user id_file port option 5 Processed sensor th
14. fan trays PEMs and SAP gt Chapter 3 3 b SSH into the backup shelf manager IP 192 168 1 3 user root no password c Set the rc2 variable to etc rc acb HPDL gt Chapter 3 4 d Terminate the ssh connection with exit e On the shelf manager in slot 0x10 set the rc2 variable to etc rc acb HPDL gt Chapter 3 4 f Reboot both shelf managers simultaneously gt Chapter 3 5 Example 3 Zephyr or Ventus shelf with one shelf manager and serial connection or SSH connection to the console interface 1 Set the rc2 variable to etc rc acb4 gt Chapter 3 4 2 Install the firmware gt Chapter 3 1 3 Install the FRU files in the shelf manager and shelf and DSAP gt Chapter 3 3 Note Do not install FRU files in the fan trays ISAP or PEMS 4 setthe rc2 variable to etc rc acb HPDL gt Chapter 3 4 5 reboot the shelf manager gt Chapter 3 5 Example 4 Zephyr or Ventus shelf with two shelf managers and serial connection or SSH connection to the console interface of the active shelf manager in 0x10 1 Programming the firmware and the shelf manager FRU file on the shelf manager in slot 0x10 a Set the rc2 variable to etc rc acb4 gt Chapter 3 4 b Connect to the active shelf manager in slot 0x10 and install the firmware gt Chapter 3 1 c Doa clia switchover to switch back to 0x10 d Install the shelf manager FRU file on 0x10 gt Chapter 3 3 e Reboot the shelf manager using the reboot command 2 Programming the firmw
15. gt Download of FRU data to Fan Tray 2 sh fru_update 20 5 lt Fan Tray FRU file name gt Download of FRU data to PEM A sh fru_update 20 6 lt PEM FRU file name gt Download of FRU data to PEM B sh fru_update 20 7 lt PEM FRU file name gt Download of FRU data to the SAP sh fru_update 20 8 lt SAP FRU file name gt Release Note Pentair Schroff Firmware part number 63998 08175 19 34 October 22 2013 gt PENTAIR eTA Shelf Manager FRU file update In a system with only one Shelf Manager please consult the user manual of the shelf to determine the shelf manager address locations 10 and 12 Download of FRU data to the Shelf Manager in 0x10 sh fru update 10 0 lt Shelf Manager FRU file name gt Download of FRU data to the Shelf Manager in 0x12 sh fru update 12 0 lt Shelf Manager FRU file name gt Note The upgrade process of the shelf manager may take several minutes 3 4 Setting the environmental variable rc2 After successful upgrade set the RC2 environment variable and reboot the system setenv rc2 etc rc acb HPDL Please make sure that the rc2 variable is set correctly A common problem that causes the Shelf Manager to not work properly is to set the rc2 variable incorrectly You must set the rc2 variable on both shelf managers to the same value e g etc rc acb HPDL You can check the setting with getenv rc2 After setting the variable reboot the shelf manager If one of the shelf mana
16. in the tmp directory on the FTP server A single command is executed on the active Shelf Manager to upgrade the FLASH images This command will download the FLASH images using FTP copy them into the alternate FLASH memory configure the Shelf Manager for a provisional boot and reboot the Shelf Manager If all goes well the reliable upgrade watchdog timer will be reset after Linux boots and the provisional FLASH memory will be configured as the current FLASH memory If the upgrade fails the original FLASH memory will be configured as the current FLASH memory and the Shelf Manager will reboot In the example below 192 168 0 7 is the TCP IP address of the FTP server You will need to substitute the TCP IP address of your FTP server In the example tmp is the directory on the FTP server that contains the new FLASH images You will need to substitute the directory name on your FTP server that contains the FLASH images In the example ftp is a valid userid on the FTP server and ftppw is the password for the userid You will need to substitute both ftp and ftppw for a valid userid and password on your FTP server This is an example of the Reliable Upgrade command rupgrade tool s v d k 63998 08175 shmm500 kernel r 63998 08175 shmm500 rfs u 63998 08175 u boot proto ftp 192 168 0 7 tmp ftp ftppw hook erase Note This command is on a single line This is an example of the Reliable Upgrade command a
17. rw nfsroot serverip rootpath addip setenv bootargs bootargs ip ipaddr serverip gatewayip netmas k hostname ipdevice addmisc setenv bootargs bootargs quiet console S console baudrate reli able upgrade reliable upgrade Release Note Pentair Schroff Firmware part number 63998 08175 27 34 October 22 2013 gt PENTAIR eTA nfs tftpboot 80800000 bootfile run nfsargs addip addmisc bootm bootcmd run ramargs addmisc bootm kernel start rfs_start console ttys0 quiet quiet ipdevice eth0 ipldevice ethl ipladdr 192 168 1 2 gatewayip 192 168 0 1 rmcpaddr 192 168 0 2 hostname shmm500 flash_reset n password reset n logging ram time zone UTC rc_ifconfig n start_rc2_ daemons y reliable upgrade y re2 etc rc acb HPDL stdin serial stdout serial stderr serial ethaddr 00 50 c2 4a 17 e4 ethladdr 00 50 c2 4a 17 e5 serial 08005937 kernel start 0xb b00000 rfs_start 0xbfc40000 ethact AulX00 ETHERNET bootdelay old 3 post_normal bootdelay 3 Environment size 1201 3067 bytes Release Note Pentair Schroff Firmware part number 63998 08175 28 34 October 22 2013 SchrofF gt PENTAIR Mancen TEA 8 Revision History 3 2 0 1 New and Changed Features for This Release 1 2 3 15 16 Abnormal signal handling and diagnostic output in the utility has been improved The utility has been enhanced to allow reads and writes of up to 256 byte
18. the use of this range for external addresses When Shelf Manager is terminated via the CLI command terminate each disabling of a network interface is accompanied by clearing of its IP address This prevents duplication of that IP address in the network when the Shelf Manager is later restarted on the same ShMM In HPDL support has been added for volatile devices These are devices that can dynamically appear and disappear or be powered on and off while the FRU that owns them stays active The Shelf Manager monitors the presence of devices described with the qualifier VOLATILE in the HPDL description and configures them dynamically when they become present The Redundancy and CPLD State Sensor in the Shelf Manager now detects and reports a double ACTIVE state when both Shelf Managers consider themselves active This state can occur only as a result of a hardware malfunction CLI commands now report an intelligent RTM that is an RTM that implements a local management controller specifically an MMC as an IRTM instead of as AMC 15 CLI command sensordata now shows symbolic names for the active states of the Redundancy and CPLD State and Reboot Reason sensors A new configuration variable PET_OEM_WITH_SEVERITY_STRINGS controls whether severity strings are included in Platform Event Traps in OEM plain text and multi variable formats Redundancy information exchanged between the active and backup Shelf Managers over the Software Redu
19. 55 255 0 The command clia setlanconfig 1 subnet_mask 255 255 255 128 will set Subnet Mask of the Subnet Mask to 255 255 255 128 You need to substitute 255 255 255 128 in the example for the Subnet Mask of your network You can use the command ping 192 168 0 6 to test the network connection to the FTP server You need to substitute 192 168 0 6 in the command for the IP address of the FTP server on your network The example below shows a successful ping test ping c 2 192 168 0 6 PING 192 168 0 6 192 168 0 6 56 data bytes 64 bytes from 192 168 0 6 icmp seq 0 ttl 64 time 1 5 ms 64 bytes from 192 168 0 6 icmp seq 1 ttl 64 time 1 9 ms 192 168 0 6 ping statistics 2 packets transmitted 2 packets received 0 packet loss round trip min avg max 1 5 1 7 1 9 ms Connect a serial console cable to from a terminal or PC running a terminal emulator Hypercom Minicom Hyperterminal etc to the console port of the Shelf Manager Set the terminal or emulator to 115200 N 8 1 115200 baud no parity 8 bits per character 1 stop bit STEP 2 Upgrade Process Put the three Reliable Upgrade FLASH images 63998 08175 shmm500 kernel 63998 08175 shmm500 rfs 63998 08175 u boot on a FTP server that is on the same network as the Shelf Managers Release Note Pentair Schroff Firmware part number 63998 08175 10 34 October 22 2013 gt PENTAIR e For this example the Reliable Upgrade FLASH images were put
20. MC based FRUs In order to get a list of supported FRU numbers and associated FRU types for your specific shelf type use the commands clia fru lt IPMC gt lt FRU ID gt Description 10 0 Shelf Manager in slot 0x10 12 0 Shelf Manager in slot 0x12 20 1 Shelf SEEPROM 1 20 2 Shelf SEEPROM 2 20 3 SAP Examples sh var nvdata fru_update 20 1 var nvdata 11596101HABIN bin Writes Shelf FRU data of the shelf with part number 11596 101 into FRU_data SEEPROM 1 and restores the variables listed in Table 1 sh var nvdata fru_update 20 3 var nvdata 21596132ABBIN bin Writes Fan Tray FRU data into the FRU_data SEEPROM of the left Fan Tray Fan Tray 0 and restores the variables listed in Table 1 Complete update The example below shows the complete update of the FRU files in the shelf and on the shelf managers in a 14 or 16 slot Pentair Schroff ATCA shelf In order to get a list of supported FRU numbers and associated FRU types for your specific shelf type use the command clia fru Change to the var nvdata directory cd var nvdata Shelf FRU file update Download of FRU data to shelf SEEPROM 1 sh fru_update 20 1 lt Shelf FRU file name gt Download of FRU data to shelf SEEPROM 2 sh fru_update 20 2 lt Shelf FRU file name gt Download of FRU data to Fan Tray 0 sh fru_update 20 3 lt Fan Tray FRU file name gt Download of FRU data to Fan Tray 1 sh fru_update 20 4 lt Fan Tray FRU file name
21. N bin Schroff AivanceaTCA 14slot pull cooling rad IPMB Full Mesh DC 2slot push pull cooling bused IPMB node node DC 14slot pull cooling bused IPMB Dual Star DC 14slot pull cooling rad IPMB Dual Star DC 14slot pull cooling bused IPMB Full Mesh DC 14slot pull cooling rad IPMB Full Mesh DC 6slot push pull cooling bused IPMB Triple Repl Mesh DC 6slot push pull cooling rad IPMB Triple Repl Mesh DC 14slot push cooling bused IPMB Dual Star DC 14slot push cooling rad IPMB Dual Star DC 14slot push cooling bused IPMB Full Mesh DC 14slot push cooling rad IPMB Full Mesh DC 6slot push pull cooling bused IPMB Triple Repl Mesh AC 14slot 400W 40G push pull cooling bused IPMB Dual Star DC 14slot 400W 40G push pull cooling radial IPMB Dual Star DC 14slot 400W 40G push pull cooling bused IPMB Dual Dual Star DC 14slot 400W 40G push pull cooling radial IPMB Dual Dual Star DC 6slot 450W 40G push pull cooling bused IPMB Triple Repl Mesh AC DC 14slot 300W 40G pull cooling bused IPMB Dual Star DC 14slot 300W 40G pull cooling radial IPMB Dual Star DC 14slot 300W 40G pull cooling bused IPMB Dual Star AC 14slot 300W 40G pull cooling radial IPMB Dual Star AC October 22 2013 gt PENTAIR etA 3 Upgrading the Shelf Manager to release 3 2 0 1 There are two ways of upgrading the Shelf Manager firmware 1 TFTP Upgrade Procedure Yo
22. SchrofFf gt PENTAIR eTA Release Notes Pentair Schroff firmware part number 63998 08175 Based on Pigeon Point Systems PPS firmware release V3 2 0 1 for ShMM 500 Release Date August 22 2013 Release History Release date Pentair Schroff FW P N PPS version December 14 2006 63998 04652 V2 3 2 April 26 2007 63998 04660 V2 4 2 January 18 2008 63998 04664 V2 5 1 July 28 2008 63998 08152 V2 5 3 January 29 2010 63998 08160 V2 6 4 4 September 14 2010 63998 08161 P4 V2 7 0 4 October 7 2010 63998 08162 V2 7 1 July 1 2011 63998 08165 V2 7 4 January 19 2012 63998 08170 V2 8 1 June 6 2012 63998 08171 V2 8 2 1 June 29 2012 63998 08172 V2 8 3 October 22 2013 63998 08175 V3 2 0 1 Introduction The firmware package 63998 08175 zip contains Firmware release 3 2 0 1 for the ShMM 500 The PPS supplied RFS image has been modified by Pentair Schroff to adapt the firmware to Pentair Schroff ATCA shelves The kernel image has not been modified and is identical to the PPS kernel image The U boot environment has been modified to reflect the necessary non volatile system settings for this firmware running on Pentair Schroff shelf managers The Pentair Schroff part number for this firmware release is 63998 08175 Important Notice The flash memory device on the SAMM 500 has gone to end of life status SAMM 500s produced after November 1 2012 will contain a new version of the fla
23. T 221 Goodbye rupgrade tool copying 63998 08175 shmm500 rfs from 10 183 7 176 tmp to tmp using ftp protocol 220 FileZilla Server version 0 9 36 beta 220 written by Tim Kosse Tim Kosse gmx de 220 Please visit http sourceforge net projects filezilla USER ftp 331 Password required for ftp PASS KKK 230 Logged on TYPE I 200 Type set to I PASV 227 Entering Passive Mode 10 183 7 176 11 2 RETR tmp 63998 08175 shmm500 rfs 150 Connection accepted 226 Transfer OK QUIT 221 Goodbye rupgrade_ tool invoking scripts step4v u 63998 08175 u boot k 63998 08175 shmm500 kernel r 63998 08175 shmm500 rfs proto ftp 10 183 7 176 tmp ftp ftp hook erase rupgrade_ tool copying 63998 08175 u boot from tmp to dev mtdchar8 using cp protocol rupgrade_ tool copying 63998 08175 shmm500 kernel from tmp to dev mtdchar7 using cp protocol rupgrade tool copying 63998 08175 shmm500 rfs from tmp to dev mtdchar9 using cp protocol rupgrade tool invoking scripts step4h erase etc upgrade step4hshm Stopping Shelf Manager Done etc upgrade step4hshm Cleaning new var partition Done Cleaning new etc partition Done etc upgrade step4hshm Copying etc ssh keys Done 4 4 4 etc upgrade step4hshm 4 4 etc upgrade step4hshm Upgrade complete rupgrade tool image s copy OK rupgrade_ tool watchdog started rupgrade_ tool selected provisional flash rupgrade_ tool reboot Restarting system
24. UG_2_8 1 _20111207 pdf Example 1 Shelf with one shelf manager and serial connection or SSH connection to the console interface 1 Install the firmware gt Chapter 3 1 2 Install the FRU files gt Chapter 3 3 3 set the rc2 variable to etc rc acb HPDL gt Chapter 3 4 4 reboot the shelf manager gt Chapter 3 5 Example 2 Shelf with two shelf managers and serial connection or SSH connection to the console interface of the active shelf manager in 0x10 1 Programming the firmware and the shelf manager FRU file on the shelf manager in slot 0x10 a Connect to the active shelf manager in slot 0x10 and install the firmware gt Chapter 3 1 b Do a clia switchover to switch back to 0x10 c Install the shelf manager FRU file on 0x10 gt Chapter 3 3 d Reboot the shelf manager using the reboot command 2 Programming the firmware and the shelf manager FRU file on the shelf manager in slot 0x12 a Connect to the active shelf manager in slot 0x12 and install the firmware gt Chapter 3 1 b Do a clia switchover to switch back to 0x12 c Install the shelf manager FRU file on 0x12 gt Chapter 3 3 d Reboot the shelf manager using the reboot command 3 Install the FRU files in the shelf and set the correct rc2 variable Release Note Pentair Schroff Firmware part number 63998 08175 8 34 October 22 2013 gt PENTAIR eTA a Connect to the shelf manager in slot 0x10 and install the FRU files for the shelf
25. _EVENT_AT_STARTUP was TRUE there could be a missing M6 gt M1 event on the physical Shelf Management Controller ShMC after a switchover This variable was first introduced in Release Note Pentair Schroff Firmware part number 63998 08175 32 34 October 22 2013 2 8 N oO SchrofF PENTAIR AivanceaTCA release 2 8 0 and its default value is FALSE therefore only customers who specifically chose this behavior were affected by this bug Network interfaces could be configured incorrectly in the USE_DHCP TRUE configuration if channel parameters were not initialized or had a zero IP address New and Changed Features for This Release 11 12 This release is based on an update of Monterey Linux that includes the following specific changes e ShMM 500 ShMM 1500 Support has been added in the kernel for S29GL S Spansion Flash devices e ShMM 500 SAMM 1500 The kernel level implementation of ShMM runtime self tests has been modified to prevent CPU starvation for other tasks while the tests are running e ShMM 500 ShMM 1500 U Boot has been modified to automatically switch over to the other Flash bank in the case of a CRC error in the kernel or RFS image in the current Flash bank e ShMM 1500 The kernel has been modified to allow IP addresses in the range 127 x x x to be used for external communications Previously all such addresses could be used only on the loopback interface The ShMM 500 already allows
26. and switchover this parameter overrides the behavior described in the previous item and causes the newly active Shelf Manager to re read the Chassis HPDL description after the switchover The output of the CLI command sensordata for the state mask has been changed to avoid confusion with the sensor status flags In the output of the CLI command alarm info the sensor type and sensor number have been swapped to conform better to the format of SEL entries shown by the sel command Anew configuration variable WATCHDOG_TIMEOUT has been introduced it specifies the ShMM watchdog timeout interval in seconds The performance of the CLI commands fru and board has been improved Anew configuration parameter ALLOWED_CIPHER_SUITES has been implemented this parameter specifies a bit mask of the IPMI 2 0 cipher suites that are allowed for use by a LAN client of the Shelf Manager The default value is OxFFFFFFFF 1 decimal which indicates that all supported cipher suites can be used In order to prevent the bit bang 12C driver from unnecessarily yielding the processor to another process the sysctl variable dev mo i2c scl_high_waitcount was added to the driver This variable sets the time in microseconds that the driver waits for the I2C signal SCL to transition high before giving up the processor to another process The default value of this variable is 5 If the variable is set to 0 the driver will check SCL once and then immediately yield the p
27. are and the shelf manager FRU file on the shelf manager in slot 0x12 a Set the rc2 variable to etc rc acb4 gt Chapter 3 4 b Connect to the active shelf manager in slot 0x12 and install the firmware gt Chapter 3 1 c Do a clia switchover to switch back to 0x12 d Install the shelf manager FRU file on 0x12 gt Chapter 3 3 e Reboot the shelf manager using the reboot command 3 Install the FRU files in the shelf and set the correct rc2 variable a Connect to the shelf manager in slot 0x10 and install the FRU files for the shelf and DSAP Note Do not install FRU files in the fan trays ISAP or PEMS gt Chapter 3 3 b SSH into the backup shelf manager IP 192 168 1 3 user root no password c Set the rc2 variable to etc rc acb HPDL gt Chapter 3 4 d Terminate the ssh connection with exit e On the shelf manager in slot 0x10 set the rc2 variable to etc rc acb HPDL gt Chapter 3 4 f Reboot both shelf managers simultaneously gt Chapter 3 5 Release Note Pentair Schroff Firmware part number 63998 08175 9 34 October 22 2013 Schroff gt PENTAIR Ait CA 3 1 Reliable Upgrade Procedure The Reliable Upgrade procedure will copy the new firmware flash images from an FTP server on your network to RAM on the ShMM 500 and then copy the images to flash memory STEP 1 Network settings In order to retrieve the new firmware images the Shelf Manager needs a network connection to your FTP server If this already
28. aster only 12C bus showing addresses of all devices present on the bus and for repeating operations with a new c option and measuring the elapsed time 27 ShMM inventory attributes serial number hardware revision part number and manufacturing date have been made available in the FRU Information format the corresponding FRU information is accessible at the Shelf Manager physical IPMB address FRU ID 254 28 The handling of the FRU Information for the logical Shelf Manager IPMB 20h FRU 0 has been changed Now this FRU information is read only and automatically generated 29 The handler of the Set Fan Policy command has been reworked to allow zero as a site number 30 Anew CLI command variable has been implemented to access HPDL variables 31 The clia utility has been enhanced to support non root user restrictions via a list of allowed commands from the file letc clia conf 32 Read only SNMP variables representing the following FRU Information fields have been implemented Product Asset Tag Product FRU File ID and Board FRU File ID These variables are defined for ATCA boards PEMs fan trays power supplies and dedicated Shelf Managers 33 The maximum possible FRU ID for a logical Shelf Manager in an HPDL configuration has been increased from 16 to 32 34 The performance of the firmware firewall implementation in the Shelf Manager during Shelf Manager startup has been improved 35 The bus number for the master only 12C multi
29. ding is enabled If Ethernet bonding is enabled on the shelf manager the Base Interface switch on both switch blades needs to have the same subnet The shelf manager commands clia setlanconfig and clia getlanconfig are used to configure and display the RMCP IP address for the shelf manager For more information on this and other possible Ethernet configurations see section 3 4 in the PPS Shelf Manager Users Guide Release Note Pentair Schroff Firmware part number 63998 08175 26 34 October 22 2013 gt PENTAIR eTA 7 Firmware part number 63998 08175 configuration files The configuration file etc shelfman conf contains all PPS default configuration variables for the Shelf Manager Variables that have been modified for Firmware version 63998 08175 are stored in the additional configuration files etc shelfman conf ACB HPDL The content of the custom specific configuration file is listed below cat etc shelfman conf ACB HPDL etc shelfman conf ACB HPDL Created by MGT 4 February 2008 Modified by MGT 3 December 2008 added static IP assignment for USB COOLING MANAGEMENT acb Schroff cooling algorithm CARRIER _OPTIONS NEBS TACH MASK 0x0F Enables NEBS cool
30. duct Info Area Mfg Date Time Board Info Area Product Version Product Info Area Asset Tag Product Info Area IP address OEM record Shelf Manager IP Connection Gateway OEM record Shelf Manager IP Connection Netmask OEM record Shelf Manager IP Connection Internal Use Area Complete FRU ID file update Syntax sh lt path gt fru_update lt IPMC gt lt FRU ID gt lt path gt lt filename gt lt path gt Location of the FRU files default var nvdata lt filename gt Name of the FRU file Example 11596401HABIN bin 11596401 Shelf or FRU part number HA Revision of the FRU data file BIN Identification for a FRU data file bin Format of FRU data file The table below lists valid values for lt IPMC gt and lt FRU ID gt for a 14 or 16 slot Pentair Schroff shelf with managed FRUs In order to get a list of supported FRU numbers and associated FRU types for your specific shelf type use the commands clia fru lt IPMC gt lt FRU ID gt Description 10 0 Shelf Manager in slot 0x10 12 0 Shelf Manager in slot 0x12 20 1 Shelf SEEPROM 1 20 2 Shelf SEEPROM 2 20 3 Fan Tray 0 20 4 Fan Tray 1 20 5 Fan Tray 2 20 6 PEM 0 20 7 PEM 1 20 8 SAP Release Note Pentair Schroff Firmware part number 63998 08175 18 34 October 22 2013 gt PENTAIR Ieta The table below lists valid values for lt IPMC gt and lt FRU ID gt for a 6 14 or 16 slot Pentair Schroff shelf with IP
31. e from a multi byte response of a PMBus command was handled incorrectly 18 The implementation of the command Get Power Level in the Shelf Manager did not return the completion code Invalid data in request for an invalid power type in the request 19 During initial startup prior to the Shelf FRU Information being found CLI commands could show IPMCs that were not actually present in the shelf to be present and in the M4 Normal Hot Swap state 20 Amemory leak was possible on the active Shelf Manager as a result of software termination of the backup Shelf Manager via the CLI command terminate and subsequent restart of the backup Shelf Manager 21 This release is based on an update of Monterey Linux that includes the following specific changes a rupgrade_tool and U boot incorrectly referred to the flash halves based on the ADM1060 PLBx_EN INVOP reading b rupgrade_tool could crash if an incorrect port number was specified 22 The Shelf Manager API has been enhanced to support changes in Chassis Board and Product Info Areas of FRU Information 23 The maximum possible FRU ID for a logical Shelf Manager in an HPDL configuration has been increased from 16 to 32 24 Aretry has been added to the presence check operation for logical Shelf Manager FRUs in an HPDL configuration as a workaround for a potential misreading 25 The SNMP daemon now sends output to the system log instead of to a separate file and uses the tmp directory for the
32. en in the table FRU ID Files below The FRU files are shipped with this release and are stored on the ShMM 500 in the var nvdata directory Note It is possible to run the existing shelf managers and shelf in non HPDL mode with V3 2 0 1 firmware Because new shelf manager and shelf designs will only be supported in HPDL mode we recommend that shelf managers are run in HPDL mode The Linux command getenv rc2 will show how the shelf manager is configured If the result is rc acb HPDL then the shelf manager is configured to run in HPDL mode Pentair Schroff Firmware part number 63998 08175 2 34 October 22 2013 gt PENTAIR eTA CONTENT 1 Pentair Schroff shelf manager versions scciesessincececvincastsatciureceincevasVeecencseieeereseveenesiwearersvaees 4 2 Preparations ssieinesi a E E E e eee E E eee 6 3 Upgrading the Shelf Manager to release 3 2 0 1 nsnssssnsennrnnereserrenerrnrressrrrrnrrnnnrssrrrrnrnn 8 3 1 Reliable Upgrade Procedure cceeeeececcneee eee eeeeeneaeeeeeeeeeeeeeaaaaaaeeeeeeeesenesaaaeeeeenes 10 3 2 TFTP Upgrade Procedure a ote cacteeie cei ew ho eanewaeiie es 15 So Updating FRU data fil Sirisiri eirinen E AERE 18 3 4 Setting the environmental Variable rC2 sssssseesneesseerrrrrrtrtssrrrtrrnrnrsserrrrnrnnnneserennee 20 3 5 Restart the SY SUC oa oes ac ose ce az gee cacenececeeagcasancubsacoeendaaidussteneedeeocausenvenneeieeaies 20 4 Special tests for HPDL Upgrade
33. es 184 92 kB 0 18 MB Load Address 0x9FC00000 Entry Point 0x00000000 Current Kernel mage Name 63998 08175 Kernel Linux 2 4 26 Created Tue Oct 22 13 01 18 2013 mage Type MIPS Linux Kernel Image gzip compressed Data Size 879654 Bytes 859 04 kB 0 84 MB Load Address 0x80100000 Entry Point 0x802D4040 Current RFS mage Name 63998 08175 RFS 3 2 0 1 Created Tue Oct 22 13 01 18 2013 mage Type MIPS Linux RAMDisk Image gzip compressed Data Size 3918820 Bytes 3826 97 kB 3 74 MB Release Note Pentair Schroff Firmware part number 63998 08175 16 34 October 22 2013 gt PENTAIR eTA Load Address 0x00000000 Entry Point 0x00000000 Alternate Boot mage Name 63998 08174 U Boot 1 1 4 Created Fri Jun 29 17 20 06 2012 mage Type MIPS Linux Firmware uncompressed Data Size 189104 Bytes 184 67 kB 0 18 MB Load Address 0x9FC00000 Entry Point 0x00000000 Alternate Kernel mage Name 63998 08174 Kernel Linux 2 4 26 Created Fri Jun 29 17 20 06 2012 mage Type MIPS Linux Kernel Image gzip compressed Data Size 879448 Bytes 858 84 kB 0 84 MB Load Address 0x80100000 Entry Point 0x802D4040 Alternate RFS mage Name 63998 08174 RFS 3 1 1 Created Fri Jun 29 17 20 06 2012 mage Type MIPS Linux RAMDisk Image gzip compressed Data Size 3856029 Bytes 3765 65 kB 3 68 MB Load Address 0x00000000 Entry Point 0x00000000 Pigeon Point Shelf Manager Command Line Interpre
34. exists through the Base Interface hub then no further network configuration is required If your Base Interface hubs are not connected to a network you can use the RJ 45 connector on the front panel of the Shelf Manager to connect to the FTP server on your network If you need to use the front panel Ethernet connector you need to set the jumpers on the Shelf Manager to route the primary Ethernet port to the front panel When the jumpers are on the pins towards the front panel the Ethernet is connected to the front panel connector See the Shelf User Manual for details of the jumper setting You need to configure the IP Address that the Shelf Manager will use on the network to access the FTP server The command clia setlanconfig 1 ip 192 168 0 2 will set the IP Address of the active Shelf Manager to 192 168 0 2 The active Shelf Manager is the one with the green LED illuminated and not blinking You need to substitute 192 168 0 2 in the example for your desired IP Address If your Shelf Manager is on a different network than your FTP server then you need to configure the Default Gateway The command clia setlanconfig 1 dft_gw_ip 192 168 0 1 will set the IP Address of the Default Gateway to 192 168 0 1 You need to substitute 192 168 0 1 in the example for the IP Address of the Default Gateway on your network If you use subnets on your network then you need to change the Subnet Mask from the default value of 255 2
35. fy the successful upgrade you can verify the version that you are running with the version command version Current Boot mage Name 63998 08175 U Boot 1 1 4 Created Tue Oct 22 13 01 18 2013 mage Type MIPS Linux Firmware uncompressed Data Size 189360 Bytes 184 92 kB 0 18 MB Load Address 0x9FC00000 Entry Point 0x00000000 Current Kernel mage Name 63998 08175 Kernel Linux 2 4 26 Created Tue Oct 22 13 01 18 2013 mage Type MIPS Linux Kernel Image gzip compressed Data Size 879654 Bytes 859 04 kB 0 84 MB Load Address 0x80100000 Entry Point 0x802D4040 Release Note Pentair Schroff Firmware part number 63998 08175 13 34 October 22 2013 gt PENTAIR ieta Current RFS Image Name 63998 08175 RFS 3 2 0 1 Created Tue Oct 22 13 01 18 2013 Image Type MIPS Linux RAMDisk Image gzip compressed Data Size 3918820 Bytes 3826 97 kB 3 74 MB Load Address 0x00000000 Entry Point 0x00000000 Alternate Kernel Image Name 63998 08174 Kernel Linux 2 4 26 Created Fri Jun 29 17 20 06 2012 Image Type MIPS Linux Kernel Image gzip compressed Data Size 879448 Bytes 858 84 kB 0 84 MB Load Address 0x80100000 Entry Point 0x802D4040 Alternate RFS Image Name 63998 08174 RFS 3 1 1 Created Fri Jun 29 17 20 06 2012 Image Type MIPS Linux RAMDisk Image gzip compressed Data Size 3856029 Bytes 3765 65 kB 3 68 MB Load Address 0x00000000 Entry Point 0x00000000 Pigeon Point
36. gers is set to a different variable it will constantly reboot signaling that it is not working properly 3 5 Restart the system If you use redundant shelf managers you need to reboot both shelf managers at the same time There are several ways of doing this 1 Power cycle the complete shelf 2 Remove both shelf managers from their slots Wait minimum 5 sec Re insert the shelf managers 3 Push the reset buttons on the front panel of both shelf managers use a ball pen tip or similar within a maximum delay of 3 sec 4 Use the script fru_data_refresh in var nvdata cd var nvdata sh fru_data_refresh Release Note Pentair Schroff Firmware part number 63998 08175 20 34 October 22 2013 gt PENTAIR eTA 4 Special tests for HPDL upgrade With the new HPDL scheme some tests should be done after the upgrade to verify the correct installation of the firmware and the FRU files These tests should be done on both shelf managers in a redundant system 1 Correct version installed and configured use the version command to check for the correct firmware version numbers under current boot current kernel and current rfs All should be 63998 08175 The Pigeon Point Shelf manager version should be 3 2 0 1 The carrier setting should be HPDL ACB version Current Boot mage Name 63998 08175 U Boot 1 1 4 Created Tue Oct 22 13 01 18 2013 mage Type MIPS Linux Firmware uncompressed Data Size 189360 Bytes
37. his procedure to set the U boot environment variables back to their default values 1 Reboot the shelf manager with the reboot command 2 Stop the shelf manager from booting Linux by entering a character on the serial console when Hit any key to stop autoboot is displayed 3 Enter the U boot commands eeprom write 80400000 0 1800 and reset 4 Stop the shelf manager from booting Linux by entering a character on the serial console when the U boot banner is displayed 5 Enter the U boot commands save save and reset set to the correct value for your shelf manager carrier board You must set the rc2 variable on both shelf managers to the same value e g etc rc acb HPDL See section 1 for the correct RC2 value You can check the setting with getenv rc2 After setting the variable reboot the shelf manager If one of the shelf managers is set to a different variable it will constantly reboot signaling that it is not configured properly i Note If you set the U boot environment to the factory default values the rc2 variable may not be U Boot 1 1 4 Oct 22 2013 09 00 47 CPU Au1550 324 MHz id 0x02 rev 0x00 Board ShMM 500 S N 08026624 DRAM Samsung K4S511633F 128 MB Flash 64 MB In serial Out serial Err serial ADM1060 configuration version 1 5 Net AulX00 ETHERNET Hit any key to stop autoboot 0 shmm500 eeprom write 80400000 0 1800 EEPROM 0x50 write addr
38. ing of this signal is re enabled when system shell is started if the CARRIER value is not set to PPS Release Note Pentair Schroff Firmware part number 63998 08175 29 34 October 22 2013 PENTAIR aTa This workaround was implemented for ShMM carriers with a floating CD signal to avoid unexpected console session terminations especially during initial programming b The net snmp build procedure was optimized to reduce binary size and to exclude MIB related warnings in the snmpd log at daemon startup 21 The SNMP daemon now sends output to the system log instead of to a separate file and uses the tmp directory for the configuration digest file This is done to avoid unnecessary writes to the etc filesystem that may reduce free space 22 There is a new configuration parameter ENABLE_RTC_TRICKLE_CHARGER if this parameter is set to TRUE the trickle charge feature of the RTC DS1339 device on the ShMM is enabled 23 The Shelf Manager API has been enhanced to support changes in Chassis Board and Product Info Area of FRU Information 24 New ShMM diagnostics for master only 12C and IPMB buses have been implemented for all supported platforms 25 Recent events from internal Shelf Manager sensors are now not re sent in response to the Set Event Receiver command e g during a switchover if the sensors are in the Initial Update Sensor Reading Unavailable state 26 Support has been added to the utility i2ca for scanning a m
39. ing strategy Uses fan tach mask byte default is OxFF CARRIER _OPTIONS CARRIER_ FRU _LOCATION ADM1026 0 0x2e 2080 USE_TELCO 1 CARRIER OPTIONS IN EX SWITCHOFF 0 FRU_IN ADM1026 1 CARRIER _OPTIONS CARRIER_FRU_LOCATION ADM1026 0 0x2e 2110 IN EX SWITCHOFF 0 CARRIER OPTIONS CARRIER _FRU_LOCATION ADM1026 0 0x2e 2200 AX INTAKE 2 MAX E XHAUST 2 USE TELCO 1 COOLING FAN INCREASE TIMEOUT 60 COOLING FAN DECREASE TIMEOUT 60 FAN LEVEL STEP UP 2 FAN LEVEL STEP DOWN 1 NORMAL STABLE TIME 1800 INITIAL FAN LEVEL 8 MIN FAN LEVEL 3 FAN FULL SPEED DELAY 30 IPMB LINK ISOLATION TIMEOUT 60 REDUNDANCY NET ADAPTER usb0 REDUNDANCY NET ADAPTER2 usbl REDUNDANT IP ADDRESS 192 168 1 2 REDUNDANCY NETMASK 255 255 255 128 REDUNDANCY ENABLED TRUE USE_SECOND CHANNEL TRUE RMCP_NET ADAPTER2 eth1 SWITCHOVER ON HANDLE OPEN TRUE SWITCHOVER TIMEOUT ON BROKEN LINK 1 ALLOW CLEARING CRITICAL ALARM TRUE VERBOSITY OxF HPDL SHPDL The u boot configuration data environment variables is stored in a system EEPROM The default content is listed below getenv baudrate 115200 ipaddr 192 168 0 22 serverip 192 168 0 7 netmask 255 255 255 0 boot file sentry kernel ramdisk sentry rfs rootpath rootfs ramargs setenv bootargs root dev ram rw net tftpboot 80400000 S bootfile tftpboot 81200000 ramdisk run ramargs add misc bootm 80400000 81200000 nfsargs setenv bootargs root dev nfs
40. ing the rupgrade_tool utility and the new 3 2 0 1 kernel and RFS and u boot images stored in the upgrade RFS image It will then reboot For customers with early production F64M128 large capacity SAMM 500 modules an additional step may be performed to reprogram the ADM1060 to enable the larger flash memory Step 1 Rename the kernel and RFS files gt Rename 63998 08175 kernel to sentry kernel gt Rename 63998 08175 rfs to sentry rfs These images need to be placed on a TFTP server machine that is network reachable from the SaMM 500 module Step 2 Power on your ShMM 500 based hardware and interrupt the boot up process by pressing the space bar on the serial port console of the SAMM 500 U Boot 1 1 4 Shmm500 Step 3 Verify the correct name of the download images Make sure that the renamed files of Step 1 correspond to the required file names in u boot Shmm500 printenv bootfile sentry kernel ramdisk sentry rfs Step 4 Make sure that the network settings for your SAMM 500 are such that it can see the TFTP server on your network shmm500 printenv serverip ipaddr netmask gatewayip serverip 192 168 0 7 ipaddr 192 168 0 2 netmask 255 255 0 0 gatewayip 192 168 0 1 If any of these need to be changed do it as follows shmm500 setenv serverip 192 168 0 88 shmm500 saveenv Saving Environment to EEPROM shmm500 Release Note Pentair Schroff Firmware part number 63998 08175 15 34 October 22 2013
41. ion p n 21594 347 Ae e Bused IPMB version p n 21594 346 ek Serial Number Rev ACB III rc acb3 The part number of the ACB III shelf manager is on the label at the rear side of the shelf manager see photo below NEEE Radial IPMB version p n 21593 251 E SHELTLANAGER Bused IPMB version p n 21593 250 RAA PRN Serial Number Rev Release Note Pentair Schroff Firmware part number 63998 08175 4 34 October 22 2013 P PENTAIR meta The following Shelf Manager types originally shipped with ShMM 300 modules but might have been upgraded to ShMM 500 modules by the customer For upgrade instructions please contact your Pentair Schroff service partner ACB III rc acb3e ACB II rc acb2 ACB II with SAMM 500 rc acb2 HPDL SMC 1 rc acb es Release Note Pentair Schroff Firmware part number 63998 08175 5 34 October 22 2013 gt PENTAIR eTA 2 Preparations Firmware files Unzip the file 63998 08175 zip This file contains the following Pre Built images TFTP Upgrade files 63998 08175 kernel Upgrade kernel image for TFTP upgrade 63998 08175 rfs Upgrade RFS image for TFTP upgrade Reliable Upgrade files 63998 08175 shmm500 kernel Upgrade kernel for reliable upgrade 63998 08175 shmm500 rfs Upgrade RFS for reliable upgrade 63998 08175 u boot Upgrade u boot for reliable upgrade Terminal Program Connect a serial console cable to a terminal or PC running a terminal emulator Hypercom Minic
42. n what was the backup shelf manager and is now the new active shelf manager Ethernet port 2 eth1 is not used in the default configuration ShMC site 1 1 2 ce The shelf manager Ethernet ports in a Pentair Schroff shelf are wired according i a to the ATCA site dependent diagram at the left If only a single switch blade is installed in slot 1 and a shelf manager switchover occurs shelf manager 2 will not have network connectivity because its port 1 is wired to Hub slot 2 and port 2 is not used in the default configuration A 1 2 Hub a With V2 7 1 shelf manager firmware it is now possible for the shelf manager to Seana switch from port 1 to port 2 if the Ethernet link on port 1 fails If the shelf is are es manager is using port 2 it will switch from port 2 to port 1 if the Ethernet link 2 4 pair adaptable on port 2 fails The Ethernet bonding driver enslaves shelf manager ports 1 and 2 and monitors the presence of the Ethernet link The shelf manager will move the RMCP address between port 1 and port 2 if only one port has a link To enable Ethernet port bonding execute the Linux command setenv ipdevice bondo and reboot the shelf manager To disable Ethernet port bonding execute the Linux command setenv ipdevice etho and reboot the shelf manager The Linux command ifconfig bondO will show the IP address assigned to either port 1 or port 2 when Ethernet bon
43. nd the response of the Shelf Manager rupgrade_tool s v k 63998 08175 shmm500 kernel r 63998 08175 shmm500 rfs u 63998 08175 u boot proto ftp 10 183 7 176 tmp ftp ftp hook erase rupgrade_ tool PLB is 6 rupgrade_ tool EEPROM page saved rupgrade tool persistent flash is 0 rupgrade_ tool provisional flash is 1 rupgrade tool copying image s rupgrade_ tool copying 63998 08175 u boot from 10 183 7 176 tmp to tmp using ftp protocol 220 FileZilla Server version 0 9 36 beta 220 written by Tim Kosse Tim Kosse gmx de 220 Please visit http sourceforge net projects filezilla USER ftp 331 Password required for ftp PASS KKKKK 230 Logged on TYPE I 200 Type set to I PASV 227 Entering Passive Mode 10 183 7 176 11 0 RETR tmp 63998 08175 u boot 150 Connection accepted 226 Transfer OK QUIT 221 Goodbye rupgrade_ tool copying 63998 08175 shmm500 kernel from 10 183 7 176 tmp to tmp using ftp protocol 220 FileZilla Server version 0 9 36 beta 220 written by Tim Kosse Tim Kosse gmx de 220 Please visit http sourceforge net projects filezilla USER ftp 331 Password required for ftp PASS KKKKK 230 Logged on TYPE I 200 Type set to I PASV 227 Entering Passive Mode 10 183 7 176 11 1 RETR tmp 63998 08175 shmm500 kernel 150 Connection accepted 226 Transfer OK Release Note Pentair Schroff Firmware part number 63998 08175 11 34 October 22 2013 Schroff gt PENTAIR Ait QUI
44. ndancy Interface can now be sent in compressed form depending on the value of the configuration variable REDUNDANCY_COMPRESSION_THRESHOLD If message size in bytes exceeds this value then message is compressed By default this variable is set to 1 which disables compression If a new configuration variable NO_MO_M1_EVENT_AT_STARTUP is TRUE then the event M0 gt M1 is not sent for a physical Shelf Manager when it is not physically reinserted but just logically restarted the default value is set to FALSE for compatibility A PEM symbolic extension has been added to the Fru Activation Deactivation page of the Web interface so that a user can activate deactivate a PEM by its site number The Linux iftest utility has been added to the Shelf Manager RFS to help with physical network link state diagnostics The RFS Image header now contains the Shelf Manager version In addition an HPl enabled RFS image now contains the HPI version in its header These versions can be seen at U Boot startup and via the imls command Also these version strings are stored in the etc version file Previously this file contained only the build date Bug Fixes 1 2 Cached SDRs in the Shelf Manager were not immediately re read when a subsidiary FRU was removed on a remote IPM Controller this could cause problems in IntegralHPI Only one Network Time Protocol Server IP address was propagated to the NTP client from the list of time servers received from the
45. number 63998 08175 21 34 October 22 2013 gt PENTAIR 3 Correct HPDL data in carrier FRU cat var log messages grep 4 Correct SDR data in carrier FRU cat var log messages grep 5 Correct HPDL data in shelf FRU cat var log messages grep Jan 22 17 24 26 shmm500 daemon 593 bytes 6 Correct SDR data in shelf FRU cat var log messages grep Jan 22 17 24 26 shmm500 daemon 190 bytes Jan 22 17 22 21 shmm500 daemon Jan 22 17 22 21 shmm500 daemon info shelfman 248 Schrof Ff Aivancen TCA HPDL data in the FRU info shelfman 248 HPDL data in the FRU HPDL SDRs in the FRU info shelfman 248 HPDL SDRs in the FRU HPDL Chassis data in the Shelf FRU HPDL Chassis data in HPDL Chassis SDRs in the Shelf FRU info shelfman 248 HPDL Chassis SDRs in 886 bytes 318 bytes the Shelf FRU the Shelf FRU In case of errors or different output from the commands above please check the following The correct FRU files have been installed The correct shelf manager type is set in the RC2 variable Release Note Pentair Schroff Firmware part number 63998 08175 22 34 October 22 2013 gt PENTAIR eTA 5 Resetting the Shelf Manager configuration to the default values The U boot bootloader stores its environment variables in a SEEPROM You can modify these variables with either the U boot or Linux setenv command If you set the environment values incorrectly you can use t
46. om HyperTerminal etc to the serial interface of the Shelf Manager RJ45 connector SERIAL or ShMgr on the SAP Set the terminal or emulator to 115200 N 8 1 115200 baud no parity 8 bits per character 1 stop bit Login user is root with no password FRU ID files The Shelf Manager firmware images contain FRU ID files for the Shelf for most production chassis Important Note This firmware release also contains updated shelf FRU data files These FRU data files are stored in the var nvdata directory of the SAMM 500 The installation procedure of the FRU data files is described below Please make sure to install these FRU data files after installing the new firmware image two letters representing the major and minor revision level and BIN bin indicating that the contents are binary Shelf and shelf manager FRU ID files that are revision HA and higher support running the shelf managers in HPDL mode The FRU ID files for the fan tray PEM or SAP do not contain HPDL and may have a revision level lower than HA i Note The FRU ID file name is comprised if the top assembly part number without the Note If the FRU ID files that are already installed in your shelf or shelf manager are the same revision as those in the table below they do not need to be upgraded You can use the shelf manager command clia fruinfo to find the existing FRU ID file revision level in the FRU Programmer File ID field
47. ould crash when assigning power to a FRU after a switchover initiated by an SNMP request 9 The Shelf Manager did not remove SDRs from its local cache for an IPMC in state M7 after a timer initiated hot swap transition from M7 to MO for that IPMC or after a Set FRU Extracted request for that IPMC This caused undesirable issues in the IntegralHPI server the resource names were not set properly if communication with that IPMC was later recovered Release Note Pentair Schroff Firmware part number 63998 08175 30 34 October 22 2013 PENTAIR eTA ADHCP client restart after a switchover could cause failure of various shelf manager network services e g software redundancy interface or IntegralHP 11 The subnet mask could be set incorrectly on a network interface when applying network parameters received over DHCP in the case where the Shelf FRU Information had a zero filled secondary IP Connection record 12 The DHCP client did not bring up network interfaces itself assuming it was done by the Shelf Manager initialization 13 The clia fruinfo command could work incorrectly with OEM link types 14 HPDL could handle an array of LEDs incorrectly if some LEDs in the array are not defined 15 Shelf Manager termination did not work properly in the REDUNDANCY_ENABLED FALSE mode 16 The Platform Event Trap format was not synchronized via the redundancy interface 17 An HPDL PMBus signal definition for the extraction of a single byt
48. plexer isolation feature has been made configurable 36 Support for GPIO signals and fan control signals has been added to the HPDL ADT7490 driver 37 Anew configuration variable ENABLE_LOCKS_LOGGING has been implemented this variable controls whether the Shelf Manager performs internal monitoring of lock operations and is TRUE by default Setting this variable to FALSE is not recommended but can improve performance of the Shelf Manager 38 For better reliability the Ethernet ARP diagnostic on the ShMM now uses the arping utility instead of the built in kernel test Bug Fixes 1 In the HPDL driver for the ADM1031 the configuration of fan tachometer signals specifically the assignment of the divisor value was implemented incorrectly 2 In HPDL the function SET for VECTOR elements did not work it has been replaced with the PUT function that has the intended functionality 3 The PICMG defined IPMI command Get Fan Policy could work incorrectly in certain operating modes 4 Assigning a power level numbered 16 or larger to a FRU was implemented incorrectly 5 Reading the state of a shelf LED with a hardware restriction could cause an abnormal termination of the Shelf Manager 6 E keying communication links for multi slot boards worked incorrectly for boards spanning 3 or more slots 7 The startup delay and alert startup delay parameters in the Platform Event Filter PEF facility did not work properly 8 The Shelf Manager c
49. reshold values are made available via the SNMP interface 6 Anew configuration variable DHCP_SPECIAL_CLIENT_ID_FORMAT has been defined that specifies whether a specific customer defined DHCP Client ID format is to be used default is FALSE Bug Fixes 1 The utility clia crashed on the command line clia setfanlevel all Release Note Pentair Schroff Firmware part number 63998 08175 31 34 October 22 2013 PENTAIR aTa 2 In the IPMB logging mode with the log verbosity mask having the bitmask 40h set pairs of packets sent received almost at the same time could be displayed in an incorrect order 3 In HPDL based systems fan tray FRUs could be unable to respond to ATCA fan tray related commands Get Fan Speed Properties Get Fan Level Set Fan Level for a small amount of time after FRU creation 4 The SNMP interface could report incorrect values of FRU Information related variables after a board replacement Cached values related to the old board were not erased when the board was removed 2 8 1 New and Changed Features for This Release This release is based on an update of Monterey Linux that includes the following specific changes e ShMM 1500 To support the new Flash type Spansion S29GL S recent modifications in U Boot flash timings were revised and improved e ShMM 500 ShMM 1500 Support for retrieving an image from an FTP server using a nonstandard server port number has been added to the r
50. rocessor to another process When operated with the default behavior this update will prevent the driver from relinquishing the processor when the SCL signal transitions high within a few microseconds of the first check thus preventing unnecessary interruptions in the operation of the bit bang 12C interface MAC address using the mac_prefix environment variable This is only needed for PPS manufacturing contexts The ipmb_traced utility has been enhanced to support the use of HPM 2 defined mechanisms to collect IPMI messaging traces via the RMCP protocol The severity level of messages in the system log about the default gateway missing during network configuration has been reduced from error to warning for the benefit of network configurations in which the default gateway is optional A new clause ENTITY in the HPDL FRU definition has been implemented it allows explicit specification of the entity ID and instance for an HPDL defined FRU The data consistency checking algorithm in the HPDL driver for PMBus devices now treats sequential word sized readings that are less than 10 and differ by 1 as acceptable Previously a difference between readings that was within 10 of the smaller value was considered acceptable This release is based on an update of Monterey Linux that includes the following specific change a The getty utility is now configured to ignore the CD Carrier Detect modem control signal on serial port 0 Monitor
51. s Previously reads and writes were limited to 16 bytes In HPDL based systems a new approach to handle isolation of 12C multiplexers has been implemented Now isolation is supported for several multiplexer devices simultaneously using multiple ShMM GPIO lines In HPDL an extended variant of the LOCAL_BUSES statement has been implemented that enables mapping local bus numbers used in the HPDL source file to actual 12C bus numbers In HPDL it is no longer necessary to specify all fan levels in the definition of a FAN_TRAY some levels may be omitted Characteristics of the missing levels are now linearly approximated from the characteristics of their neighboring levels A new configuration variable TURBO_MODE_MIN_MISSING_FAN_TRAYS similar to the variable TURBO_MODE_MIN_FAN_FAILURES has been added It specifies the minimum number of missing inactive fan trays that triggers running the remaining fan trays at their maximum speeds If this parameter is set to 0 this feature of setting fans to their maximum speed due to missing inactive fan trays is disabled entirely The Chassis HPDL description from the active Shelf Manager is now passed to the backup Shelf Manager over the redundancy interface This allows the Shelf Manager to avoid re reading the Chassis HPDL description after a switchover and accelerates re enabling of pseudo radial links after a switchover on pseudo radial systems A new parameter clear hpdl has been added to the CLI comm
52. sh memory device and must use an updated Linux kernel The Linux kernel in version 3 2 0 1 of the shelf manager firmware has been modified so that it will work with the updated flash memory device and will also work with any previous flash memory device The ShMM 500s with the updated flash memory device will be marked with R2 after the serial number 6OOR 333M64F 128R UU Te 8000000 R2 Software Configuration Revision Number MAONI 01849000000 1 MAILARI ONANINANI MI Release Note Pentair Schroff Firmware part number 63998 08175 1 34 October 22 2013 SchrofFf gt PENTAIR AmeTeA Release Note Prior to V2 5 3 the interaction between the shelf manager and the shelf FRUs was hard coded into the shelf manager firmware Starting with Version V2 5 3 the Pentair Schroff shelf manager firmware supports Pigeon Point Systems HPDL Hardware Platform Description Language See Pigeon Point Systems document manager s FRU data and in the shelf FRU data The HPDL records contain the structure device population and definitions of the shelf hardware and behavior of the Pentair Schroff ATCA shelf Therefore as part of the upgrade process of the firmware the FRU files of the shelf manager and the shelf must be upgraded at the same time This requires a complete reboot of both shelf manager s at the same time or a power cycle of the shelf The correct assignment of the FRU files to the corresponding shelf part number is giv
53. ter Pigeon Point Shelf Manager ver 3 2 0 1 Pigeon Point and the stylized lighthouse logo are trademarks of Pigeon Point Systems Copyright c 2002 2013 Pigeon Point Systems All rights reserved Build date time Sep 5 2013 08 13 49 Carrier HPDL ACB Carrier subtype 0 subversion 0 Cooling Management Library libcooling acb so Version 3 2 0 1 Carrier Product ID 21596291 Chassis Product ID 11596160 In case the new firmware version appears in the alternate section and the old version in the current section the watchdog timer has expired and reset the firmware version to the version before the upgrade You can try the command rupgrade_tool sR to flip the firmware version the shelf manager will boot up For the necessary FRU File update and additional settings please proceed to the chapter Updating FRU data files Release Note Pentair Schroff Firmware part number 63998 08175 17 34 October 22 2013 gt PENTAIR eta 3 3 Updating FRU data files var nvdata fru_update to update FRU ID files This script saves shelf specific data like serial i Do not use the CLI command clia frudataw to update the FRU ID files Instead use the script numbers and manufacturing date A complete list of saved data is listed in table below Saved variables Variable Name Area Info Serial number Board Info Area Serial number Chassis Info Area Serial number Pro
54. u can use the TFTP Upgrade Procedure which is started from the U Boot environment of the Shelf Manager and retrieves the files from a TFTP server on your network 2 Reliable Upgrade Procedure You can also use the Reliable Upgrade Procedure This procedure will copy the new firmware flash images from an FTP server on your network to RAM on the ShMM 500 and then copy the new firmware images to flash memory Note We strongly recommend that you use the Reliable Upgrade Procedure instead of the TFTP Upgrade Procedure because it will leave the shelf manager in operating condition if the firmware upgrade fails The firmware upgrade procedure must be executed for both shelf managers in a redundant system Please make sure that both shelf managers are updated to the same firmware revision and configuration Below are four examples of the required steps to upgrade your shelf The first two examples shown below are for Pentair Schroff shelf with managed FRUs The second two examples are for Pentair Schroff shelf with IPMC based FRUs These procedures work on the factory default shelf configuration when a shelf is shipped from Pentair Schroff manufacturing Before updating deployment shelf in the field we recommend to test the procedure in your laboratory and to adapt the procedure to your specific environment if necessary For further information regarding the firmware upgrade process please see the Pigeon Point Systems user guide ShelfManager
55. upgrade_tool utility 2 Support has been added for the new style of E Keying related to 40 Gigabit Ethernet backplane links that is defined in the latest drafts of PICMG 3 1 R2 This revision is not yet adopted so it is possible that there will be further changes in the hardware platform management aspects of it prior to adoption 3 Anew configuration variable HPDL_NETWORK_ELEMENT_ID_EEPROM_OFFSET has been added This variable specifies an offset to the Network Element ID data structure in Shelf FRU Information EEPROMs it is applicable only to HPDL based systems and only if the Shelf FRU Information is configured to be retrieved from shelf level EEPROMs 4 The Shelf Manager API Application Programming Interface has been enhanced to be able to retrieve information on active E Keying links and text identifiers for FRUs Bug Fixes 1 The HPDL Driver for generic PMBus devices could incorrectly return cached FRU data for a PSU that has been extracted and is not currently installed in the shelf 2 The HPDL based Shelf Manager operating in Backup mode attempted to access Shelf FRU Information sources to verify their presence this check should be done only on the Active Shelf Manager 3 CLI commands fruinfo frudata and frudataw were incorrectly enabled on the backup Shelf Manager allowing them to attempt accesses to FRU information on non intelligent FRUs managed by the logical active Shelf Manager Access rules have been fixed to allow backup

Release Notes for V3.2.0.1

Contents

Download Pdf Manuals

Related Search

Related Contents