RM941208L11 _SDC-CF10G 802.11g Compact Flash Module with
Contents
1. NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 The test was performed in HwaYa Shielded Room 3 3 The VCCI Site Registration No is C 2047 Report No RM941208L11 Report Format Version 2 0 5 ADT CORP 4 1 3 TEST PROCEDURE a The EUT was placed 0 4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network LISN Other support units were connected to the power mains through another LISN The two LISNs provide 50 Ohm 50uH of coupling impedance for the measuring instrument b Both lines of the power mains connected to the EUT were checked for maximum conducted interference c The frequency range from 150 kHz to 30 MHz was searched Emission levels under Limit 20dB was not recorded 4 1 4 DEVIATION FROM TEST STANDARD No deviation Report No RM941208L 11 9 Report Format Version 2 0 5 ADT CORP 4 1 5 TEST SETUP Vertical Ground Reference Plane Test Receiver Horizontal Ground Reference Plane Note 1 Support units were connected to second LISN 2 Both of LISNs AMN are 80 cm from EUT and at least 80 cm from other units and other metal planes FOR THE ACTUAL TEST CONFIGURATION PLEASE REFER TO THE RELATED ITEM PHOTOGRAPHS OF THE TEST CONFIGURATION 4 1 6 EUT OPERATING CONDITIONS a Plugge2. EMC TEST REPORT REPORT NO RM941208L11 MODEL NO SDC CF10G RECEIVED Mar 21 2006 TESTED Apr 20 Apr 24 2006 ISSUED Apr 27 2006 APPLICANT Summit Data Communications Inc ADDRESS 26 South Main Street Suite 411 Akron Ohio 44311 United States ISSUED BY Advance Data Technology Corporation LAB ADDRESS No 47 14 Ling Chia Pau Tsuen Linko Hsiang 244 Taipei Hsien Taiwan R O C TEST LOCATION No 19 Hwa Ya 2 Rd Wen Hwa Tsuen Kwei Shan Hsiang Taoyuan Hsien 333 Taiwan R O C This test report consists of 32 pages in total It may be duplicated completely for legal use with the approval of the applicant It should not be reproduced except in full without the written approval of our laboratory The client should not use it to claim product endorsement by CNLA A2LA or any government agency The test results in the report only apply to the tested sample aM ops KARL ZH dh es S xD ze dark N hl 0528 No 2177 01 wi A A y h Report No RM941208L11 1 Report Format Version 2 0 5 3 1 3 2 3 3 3 4 4 1 4 1 1 4 1 2 4 1 3 4 1 4 4 1 5 4 1 6 4 1 7 5 1 5 2 5 3 5 4 5 4 1 5 4 2 5 4 3 5 4 4 5 4 5 5 4 6 5 5 5 5 1 5 5 2 5 5 3 5 5 4 5 5 5 5 5 6 ADT CORP Table of Contents CERTIEICATION ern ermee ennsnrs nen erk ennen ennanannan ern ern ennen 3 SUMMARY OF TEST RESULTS 1 0 cccccccceccceccececececeecacecucecceaeecaceceeeauecaeeceesa
3. CT Criterion A of the applicable class shall apply Performance criteria for transient phenomena applied to transmitters TT Criterion B of the applicable class shall apply Performance criteria for continuous phenomena applied to receivers CR Criterion A of the applicable class shall apply Performance criteria for transient phenomena applied to receivers TR Criterion B of the applicable class shall apply Report No RM941208L11 15 Report Format Version 2 0 5 ADT CORP The phenomena allowed during and after test in each criterion are clearly stated in the following table Performance criteria NOTE 2 Criteria During test After test Shall operate as intended Shall operate as intended May show degradation of performance Shall be no degradation of a Seenotet l performance see note 2 Shall be no loss of function Shall be no loss of function Shall be no unintentional transmissions Shall be no loss of stored data or user programmable functions May show loss of function one or more Functions shall be self recoverable May show degradation of performance Shall operate as intended after see note 1 recovering B No unintentional transmissions Shall be no degradation of performance see note 2 Shall be no loss of stored data or user programmable functions May be loss of function one or more Functions shall be recoverable by
4. MODEL NO SDC CF10G POWER SUPPLY 3 3Vdc from host equipment MODULATION TYPE CCK DQPSK DBPSK for DSSS 64QAM 16QAM QPSK BPSK for OFDM MODULATION TECHNOLOGY DSSS OFDM TRANSFER RATE 802 11b 11 5 5 2 1 Mbps 802 119 54 48 36 24 18 12 9 6Mbps NUMBER OF CHANNEL 13 OPERATING FREQUENCY 2400 2483 5MHz ANTENNA TYPE Refer to Note 1 as below O PORTS NA DATA CABLE NA NOTE 1 There are 3 antennas provided to this EUT The information about those antennas as below table TYPE OF ANTENNA ANTENNA NO MODEL NAME TYPE GAIN CONNECTOR 1 Dipole 2 2dBi UFL 2 VMT Dipole 2 2dBi UFL 3 MX3 Printed OdBi UFL Test Mode Test Condition A Antenna 2 Dipole antenna with 2 2dBi B Antenna 3 Printed antenna with OdBi After pre test for each type of antenna and chosen the antenna 2 amp 3 for test There are two test results presented in the report please refer to list as below The platform 1 Mobile Data Terminals MDTs 2 Vehicle Mounted Devices VMDs The EUT operates in the 2 4GHz frequency range lets you connect IEEE 802 11g or IEEE 802 11b devices to the network With its high speed data transmissions of up to 54Mbps The above EUT information was declared by the manufacturer and for more detailed features description please refer to the manufacturer s specifications or User s Manual Report No RM9
5. Dag al Tut Report No RM941208L11 11 Report Format Version 2 0 5 ADT CORP INPUT POWER 6dB SYSTEM ee BANDWIDTH 7 ENVIRONMENTAL 25deg C 60 RH CONDITIONS 991hPa PHASE nes TEST MODE A TESTED BY Kent Chen Corr Reading Value Value Emission Limit Level Factor dB uV dB uV dB uV dB ap A ap A ap Av QP AV METSANE EHRE SEN EEE TE 21 0 287 0 10 setz gt 1 39 27 gt 16082 0 62 EN ear os asar lasso sooo 4000 irao 5 4246 037 404 40 81 56 00 46 00 15 19 6 11 520 051 3966 40 17 60 00 50 00 1983 REMARKS 1 Q P and AV are abbreviations of quasi peak and average individually 2 The Quasi peak reading value also meets average limit and measurement with the average detector is unnecessary 3 The emission levels of other frequencies were very low against the limit 4 Margin value Emission level Limit value 5 Correction factor Insertion loss Cable loss 6 Emission Level Correction Factor Reading Value dBuY 110 Peak Reading 100 QP Limit eer AN Limit Dag al nis 1 00 10 00 30 00 MHz Report No RM941208L 11 12 Report Format Version 2 0 5 ADT CORP INPUT POWER 6dB SYSTEM ee BANDWIDTH Mis ENVIRONMENTAL 25deg C 60 RH CONDITIONS 991hP
6. Wang TECHNICAL ACCEPTANCE Da e fe u DATE Apr 27 2006 Responsible for EMC David Liu APPROVEDBY _ ne DATE Apr 27 2006 Clark Lin Deputy Manager Report No RM941208L 11 3 Report Format Version 2 0 5 2 SUMMARY OF TEST RESULTS ADT CORP After estimating all the combination of every test mode the result shown as below is the worst case The EUT has been tested according to the following specifications EMISSION Standard Test Type Result Remarks EN 55022 1998 A1 2000 A2 2003 Class B Meets Class B Limit Conducted Test PASS Minimum passing margin is 14 34dB at 4 309MHz Radiated Test NA Not Applicable NOTE The information of measurement uncertainty is available upon the customer s request IMMUNITY EN 301 489 1 V1 5 1 EN 301 489 17 V1 2 1 Standard Test Type Result Remarks EN 61000 4 2 1995 Electrostatic discharge PASS Meets the requirements of A1 1998 A2 2001 immunity test Performance Criterion A Radiated radio frequency EN 61000 4 3 2002 Meets th ts of electromagnetic field immunity PASS en A1 2002 test Performance Criterion A NOTE Please refer to Item 3 3 for more detailed description Report No RM941208L11 Report Format Version 2 0 5 ADT CORP 3 GENERAL INFORMATION 3 1 GENERAL DESCRIPTION OF EUT SDC CF10G 802 11g Compact Flash Module with Antenna AOI Connectors
7. 1792 6 11 922 053 3947 4000 60 00 50 00 20 00 7 13375 057 40 24 4081 60 00 50 00 1919 REMARKS 1 Q P and AV are abbreviations of quasi peak and average individually 2 The Quasi peak reading value also meets average limit and measurement with the average detector is unnecessary 3 The emission levels of other frequencies were very low against the limit 4 Margin value Emission level Limit value 5 Correction factor Insertion loss Cable loss 6 Emission Level Correction Factor Reading Value dBuy 110 Peak Reading QP Limit oe AY Limit Dag al 100 90 80 Report No RM941208L 11 14 Report Format Version 2 0 5 5 IMMUNITY TEST 5 1 GENERAL DESCRIPTION ADT CORP EN 301 489 1 V1 5 1 2004 11 EN 301 489 17 V1 2 1 2002 08 Product Standard EN 61000 4 2 Basic Standard Specification and EN 61000 4 3 Performance Criterion required Electrostatic Discharge ESD 8kV air discharge 4kV Contact discharge Performance Criterion B AM 1kHz Performance Criterion A Radio Frequency Electromagnetic Field Susceptibility Test RS 80 1000 MHz 1400 2000 MHz 3V m 80 5 2 GENERAL PERFORMANCE CRITERIA DESCRIPTION The Requirement of Performance Criteria Performance criteria for continuous phenomena applied to transmitters
8. 2 2 22 222222 nn En 20 RADIATED RADIO FREQUENCY ELECTROMAGNETIC FIELD IMMUNITY TEST RS 23 TEST SPECIFICATION ss ee naar a Stal 23 TESTINSTRUMENT veneensnnsnnen ern ernernennennansan ennen nennen 23 TEST PROCEDURE aaaaanananannnnanannnnnnnninnnanannnnnninnn aranan ara nann anaran Anaan Anan Anana a nnana n aranan ann 24 DEVIATION FROM TEST STANDARD 24 TEST SETUR nen ern ern E E A Ea EA aa A aaa erkennen 25 TEST Sg ESE 26 PHOTOGRAPHS OF THE TEST CONEIGURATION eeen 28 INFORMATION ON THE TESTING LABORATORIES nennen eenden 32 Report No RM941208L 11 2 Report Format Version 2 0 5 ADT CORP 1 CERTIFICATION PRODUCT SDC CF10G 802 11g Compact Flash Module with Antenna Connectors MODEL SDC CF10G BRAND Summit TESTED Apr 20 Apr 24 2006 APPLICANT Summit Data Communications Inc TEST SAMPLE ENGINEERING SAMPLE STANDARDs EN 301 489 1 V1 5 1 2004 11 EN 301 489 17 V1 2 1 2002 08 EN 55022 1998 A1 2000 A2 2003 Class B EN 61000 4 2 1995 A1 1998 A2 2001 EN 61000 4 3 2002 A1 2002 The above equipment have been tested by Advance Data Technology Corporation and found compliance with the requirement of the above standards The test record data evaluation amp Equipment Under Test EUT configurations represented herein are true and accurate accounts of the measurements of the sample s EMC characteristics under the conditions specified in this report 7 PREPARED BY DATE Apr 27 2006 essie
9. 41208L11 5 Report Format Version 2 0 5 3 2 DESCRIPTION OF TEST MODE The EUT was tested under following conditions CONDITION CONFIGURATION 1 Transmission 2 Standby There are two test results presented in the report please refer to list as below TEST MODE TEST CONDITION A Antenna 2 Dipole antenna with 2 2dBi B Antenna 3 Printed antenna with OdBi 3 3 GENERAL DESCRIPTION OF APPLIED STANDARD The EUT is a RF product According to the specifications of the manufacturer it must comply with the requirements of the following standards EN 301 489 1 V1 5 1 2004 11 EN 301 489 17 V1 2 1 2002 08 EN 55022 1998 A1 2000 A2 2003 Class B Conducted Emission Test EN 61000 4 2 1995 A1 1998 A2 2001 EN 61000 4 3 2002 A1 2002 According to clause 7 1 table 2 and clause 7 2 table 3 of EN 301 489 1 V1 5 1 2004 11 all test items have been performed and recorded as per the above standards Report No RM941208L 11 6 Report Format Version 2 0 5 ADT CORP 3 4 DESCRIPTION OF SUPPORT UNIT The EUT has been tested as an independent unit together with other necessary accessories or support units The following support units or accessories were used to form a representative test configuration during the tests NO PRODUCT BRAND MODELNO SERIAL NO FCC ID NOTEBOOK COMPUTER DELL PPOSL 3616274224 E2K24CLNS WIRELESS 2 BROADBAND BUFFALO WBR G54 140704443144
10. 55 FCC DoC Approved ROUTER NO SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS NOTE 1 All power cords of the above support units are non shielded 1 8m 2 Item 2 acted as communication partners to transfer data 3 5 CONFIGURATION OF SYSTEM UNDER TEST Test Table Wireless Router Kept in a remote area Report No RM941208L11 7 Report Format Version 2 0 5 4 EMISSION TEST 4 1 CONDUCTED EMISSION MEASUREMENT 4 1 1 LIMITS OF CONDUCTED EMISSION MEASUREMENT Class A dBuV 015 05 790 66 60 56 4 60 60 50 0 50 5 0 5 0 30 0 NOTE 3 1 The lower limit shall apply at the transition frequencies 9 ADT CORP FREQUENCY MHz Class B dBuV 66 56 56 46 2 The limit decreases in line with the logarithm of the frequency in the range of 0 15 to 0 50 MHz 3 All emanations from a class A B digital device or system including any network of conductors and apparatus connected thereto shall not exceed the level of field strengths specified above 4 1 2 TEST INSTRUMENTS DESCRIPTION amp MANUFACTURER MODEL NO SERIAL NO CALIBRATED UNTIL Test Receiver ROHDE amp SCHWARZ ESCS30 100288 Nov 02 2006 RF signal cable 5D FB Cable HYCO3 Jan 06 2007 Woken 01 LISN ESH2 Z5 100100 Jan 09 2007 ROHDE amp SCHWARZ nn LISN ROHDE amp SCHWARZ ESH3 Z5 100311 Jan 22 2007 Software ADT ADT_Cond_V3 NA NA
11. Hz 1000 MHz 1400 MHz 2000 MHz Field Strength 3 V m Modulation 1 kHz Sine Wave 80 AM Modulation Frequency Step 1 of preceding frequency value Polarity of Antenna Horizontal and Vertical Test Distance 3m Antenna Height 1 5m Dwell Time at least 3 seconds 5 5 2 TEST INSTRUMENT DESCRIPTION amp MANUFACTURER MODEL NO SERIAL NO CALIBRATED UNTIL Boonton RF Power Meter 4232A 01 02 107402 Nov 20 2006 R amp S Signal Generator SMLO3 101499 Nov 20 2006 AR ELECTRIC FIELD SENSOR FP 6001 307198 Mar 19 2007 Software ADT_RS_V450 NA NA NOTE 1 The test was performed in Hwa Ya RS Room 2 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA Report No RM941208L11 23 Report Format Version 2 0 5 5 5 3 TEST PROCEDURE The test procedure was in accordance with EN 61000 4 3 a The testing was performed in a fully anechoic chamber The transmit antenna was located at a distance of 3 meters from the EUT The frequency range is swept from 80 MHz to 1000 MHz 1400 MHz to 2000 MHz with the signal 80 amplitude modulated with a 1kHz sinewave The rate of sweep did not exceed 1 5 x 10 decade s Where the frequency range is swept incrementally the step size was 1 of preceding frequency value The dwell time at each frequency shall be not less than the time necessary for the EUT to be able to
12. ION Same as 4 1 6 Report No RM941208L11 16 Report Format Version 2 0 5 5 4 1 TEST SPECIFICATION Basic Standard EN 61000 4 2 Discharge Impedance 330 ohm 150 pF 5 4 2 TEST INSTRUMENT 5 4 ELECTROSTATIC DISCHARGE IMMUNITY TEST ESD Discharge Voltage Air Discharge 2 4 8 kV Direct Contact Discharge 2 4 kV Direct Indirect Polarity Positive amp Negative Number of Discharge Minimum 20 times at each test point Discharge Mode Single Discharge Discharge Period 1 second minimum ADT CORP DESCRIPTION amp MANUFACTURER MODEL NO SERIAL NO CALIBRATED UNTIL Thermo ESD Simulator MZ 15 EC 0310225 Sep 29 2006 ELECTROSTATIC DISCHARGE ESD 30C 1003 12 Jul 10 2006 NOISEKEN ELECTRONIC ESS 2000 ESS0382041 Jan 10 2007 DISCHARGE SIMULATOR traceable to NML ROC and NIST USA NOTE 1 The test was performed in Hwa Ya ESD Room No 2 2 The calibration interval of the above test instruments is 12 months and the calibrations are Report No RM941208L 11 17 Report Format Version 2 0 5 ADT CORP 5 4 3 TEST PROCEDURE a Electrostatic discharges were applied only to those points and surfaces of the EUT that are accessible to users during normal operation b The test was performed with at least ten single discharges on the pre selected points in the most sensitive polarity c The time interval between two successive single discharges was at leas
13. a PHASE ee TEST MODE B TESTED BY Kent Chen evel Factor E uvi dB uV dB uV dB AV QP av QP AV QP AV HH 0 170 ele 72 ar 44 82 64 98 54 98 20 16 az zl ozs oto EE EE EECH 58 98 48 98 Fa 1000 ore asss Toast 5600 4000 lirs 5 3719 035 4044 4079 56 00 46 00 1521 6 11449 044 40 23 40 67 60 00 50 00 19 33 REMARKS 1 Q P and AV are abbreviations of quasi peak and average individually 2 The Quasi peak reading value also meets average limit and measurement with the average detector is unnecessary 3 The emission levels of other frequencies were very low against the limit 4 Margin value Emission level Limit value 5 Correction factor Insertion loss Cable loss 6 Emission Level Correction Factor Reading Value Peak Reading QP Limit Pe AN Limit Dag al Report No RM941208L 11 13 Report Format Version 2 0 5 ADT CORP INPUT POWER 6dB SYSTEM ee BANDWIDTH 7 ENVIRONMENTAL 25deg C 60 RH CONDITIONS 991hPa PHASE Line 2 TEST MODE B TESTED BY _ Kent Chen Ben evel Factor dB uV dB uvy dB uvy dB AV JQP AV QP Av QP AV son aenema stent tense NEMEN CEA MCE ENE EN 56 00 46 00 Fa 3009 oa faso lassa 3600 4000 i666 5 4535 038 3770 38 08 56 00 a6 00
14. d EUT in notebook system and placed on the testing table b Prepared the wireless broadband router and placed it outside of testing area to act as communication partner for EUT c The communication partner sent data to EUT by command PING Report No RM941208L 11 10 Report Format Version 2 0 5 4 1 7 TEST RESULTS ADT CORP INPUT POWER 6dB 230V H kH SYSTEM a BANDWIDTH 7 ENVIRONMENTAL 25deg C 60 RH PHASE Line 1 CONDITIONS 991hPa S Ge TEST MODE A TESTED BY Kent Chen Corr Factor Reading Value emission Limit Level dB BH JE WI Le WI dE Proms ose nen nn niee 2 0291 010 4135 4145 6051 5051 1906 _3 2098 021 38 95 3916 56 00 46 00 1684 _4 4309 037 4129 41 66 56 00 4600 1434 5 11941 046 3277 3323 60 00 50 00 26 77 6 13 625 056 3435 3491 60 00 50 00 25 09 REMARKS 1 Q P and AV are abbreviations of quasi peak and average individually 2 The Quasi peak reading value also meets average limit and measurement with the average detector is unnecessary 3 The emission levels of other frequencies were very low against the limit 4 Margin value Emission level 5 Correction factor Insertion loss Cable loss 6 Emission Level Correction Factor Reading Value dBuy 110 Limit value Peak Reading Fa QP Limit ag Lal AN Limit
15. e test Report No RM941208L 11 26 Report Format Version 2 0 5 ADT CORP ENVIRONMENTAL 125 deg C 52 RH INPUT POWER 230Vac 50 Hz CONDITIONS 994 hPa SYSTEM TEST MODE B TESTED BY Kent Chen Frequency Begs MHz Polarity Azimuth Strength Observation Test Result 80 1000 PASS 80 1000 PASS 80 1000 PASS 80 1000 PASS 1400 2000 PASS 1400 2000 PASS 1400 2000 PASS 1400 2000 PASS NOTE There was no change compared with the initial operation during the test No unintentional response was found during the test Report No RM941208L 11 27 Report Format Version 2 0 5 ES 6 PHOTOGRAPHS OF THE TEST CONFIGURATION Conducted Emission Test Test Mode A 941208L11 Report No RM941208L11 28 Report Format Version 2 0 5 94120811 Test Mode B ADT CORP Report No RM941208L11 29 Report Format Version 2 0 5 ADT CORP ESD Test Test Mode A Test Mode B Report No RM941208L11 30 Report Format Version 2 0 5 ADT CORP RS Test Test Mode A 941208L 11 Test Mode B Report No RM941208L11 31 Report Format Version 2 0 5 ADT CORP 7 INFORMATION ON THE TESTING LABORATORIES We ADT Corp were founded in 1988 to provide our best service in EMC Radio Telecom and Safety consultation Our laboratorie
16. eecueeaueeaeesaes 4 GENERAL INFORMATION 5 GENERAL DESCRIPTION OEEUT enerverend 5 GENERAL DESCRIPTION OF APPLIED STANDARD 6 DESCRIPTION OF SUPPORT UNITA 7 CONFIGURATION OF SYSTEM UNDER TEST 2 0cccecccecceeececececcueecesececeaeecueeneeeaeesaes 7 EMISSION TEST EE 8 CONDUCTED EMISSION MEAGUREMENT eenneeneneneeneenenenenn ennn 8 LIMITS OF CONDUCTED EMISSION MEASUREMENT ccccecceeceeeecececeeceeeneeaeeeas 8 TEST INSTRUMENTS ann eneneneeneensenennsnnen sen eeneensensensnnrn ern ernennennanannan ern ern ennen 8 TEST PROCEDURE aanaaaanananannnnnnnnananannrnnnnninannnnrni annann nanara n nana a ArAnA A AAPA DADANA ARER anana anann 9 DEVIATION FROM TEST STANDARD 9 TEST EE 10 EUT OPERATING CONDITIONS ccc ccccccccceccecececceeecececeeueeceeeaeeeaeeceeeaeesaeeceteaeesaneeaees 10 EE Ee 11 IMMUNITTWTEST E arn een ennen enansan naderen nennen 15 GENERAL DESCRIPTION c cccccecceeececcceeceeececeaeecaeeceeeaeecueeceeeaeecaeecueeaeeseeeaeesaeesneeaeeeas 15 GENERAL PERFORMANCE CRITERIA DESCRIPTION nennen eenen 15 EUT OPERATING CONDITION rrn r rnrn nnne rennarar enren r errereen 16 ELECTROSTATIC DISCHARGE IMMUNITY TEST ED 17 TEST SPECIFICATION n nnenenanan nanan n a a a aa 17 TEST INSTRUMENT ccc0cccecccceccsccccrscocecesccccccsveccteceeccercesedcducuctsssescacceceucsveusnssevecesseceeces 17 TEST PROGED URE 0 0 taten beenen na na nee a ee a R niie 18 DEVIATION FROM TEST STANDARD 18 TEST SE HEEN 19 TESTRESUEISEE
17. ical coupling plane meer 0 5mm Isolation Support ESD Generator 470k H X4 Nearest Wall Horizontal coupling plane Ground Reference Plane For the actual test configuration please refer to the related item Photographs of the Test Configuration NOTE TABLE TOP EQUIPMENT The configuration consisted of a wooden table 0 8 meters high standing on the Ground Reference Plane The GRP consisted of a sheet of aluminum at least 0 25mm thick and 2 5 meters square connected to the protective grounding system A Horizontal Coupling Plane 1 6m x 0 8m was placed on the table and attached to the GRP by means of a cable with 940kQ total impedance The equipment under test was installed in a representative system as described in section 7 of EN 61000 4 2 and its cables were placed on the HCP and isolated by an insulating support of 0 5mm thickness A distance of 1 meter minimum was provided between the EUT and the walls of the laboratory and any other metallic structure Report No RM941208L 11 19 Report Format Version 2 0 5 ADT CORP 5 4 6 TEST RESULTS ENVIRONMENTAL 22 deg C 43 RH INPUT POWER 230Vac 50 Hz CONDITIONS 994 hPa SYSTEM i TEST MODE A TESTED BY Kent Chen TEST RESULTS OF DIRECT APPLICATION Discharge Contact ae Level kV Polarity Test Point Air Discharge Test Result 2 4 8 1 NA NOTE PASS Description of test point Please refers t
18. o following pages for representative mark only TEST RESULTS OF INDIRECT APPLICATION Dlecharae Horizontal Vertical g Polarity Test Point Coupling Coupling Test Result Level kV Plane Plane 2 4 4 sides NOTE NOTE PASS Description of test point 1 Front side 2 Rear side 3 Right side 4 Left side NOTE There was no change compared with initial operation during and after the test No unintentional response was found during the test Report No RM941208L 11 20 Report Format Version 2 0 5 ES ADT CORP Report No RM941208L11 21 Report Format Version 2 0 5 ADT CORP ENVIRONMENTAL 22 deg C 43 RH INPUT POWER 230Vac 50 Hz CONDITIONS 994 hPa SYSTEM i TEST MODE B TESTED BY Kent Chen TEST RESULTS OF INDIRECT APPLICATION Dlecharde Horizontal Vertical g Polarity Test Point Coupling Coupling Test Result Level kV Plane Plane 2 4 4 sides NOTE NOTE PASS Description of test point 1 Front side 2 Rear side 3 Right side 4 Left side NOTE There was no change compared with initial operation during and after the test No unintentional response was found during the test Report No RM941208L11 22 Report Format Version 2 0 5 ADT CORP 5 5 RADIATED RADIO FREQUENCY ELECTROMAGNETIC FIELD IMMUNITY TEST RS 5 5 1 TEST SPECIFICATION Basic Standard EN 61000 4 3 Frequency Range 80 M
19. respond The field strength level was 3V m The test was performed with the EUT exposed to both vertically and horizontally polarized fields on each of the four sides 5 5 4 DEVIATION FROM TEST STANDARD No deviation Report No RM941208L 11 24 Report Format Version 2 0 5 ADT CORP 5 5 5 TEST SETUP 3m measurement distance in a Full Anechoic Chamber RF Amplifier RF Generator and control system Monitoring system For the actual test configuration please refer to the related item Photographs of the Test Configuration NOTE TABLETOP EQUIPMENT The EUT installed in a representative system as described in section 7 of EN 61000 4 3 was placed on a non conductive table 0 8 meters in height The system under test was connected to the power and signal wire according to relevant installation instructions Report No RM941208L11 25 Report Format Version 2 0 5 ADT CORP 5 5 6 TEST RESULTS ENVIRONMENTAL 125 deg C 52 RH INPUT POWER 230Vac 50 Hz CONDITIONS 994 hPa SYSTEM TEST MODE A TESTED BY Kent Chen Frequency Geo a MHz Polarity Azimuth Strength Observation Test Result V m 80 1000 PASS 80 1000 PASS 80 1000 PASS 80 1000 PASS 1400 2000 PASS 1400 2000 PASS 1400 2000 PASS 1400 2000 PASS NOTE There was no change compared with the initial operation during the test No unintentional response was found during th
20. s are accredited and approved by the following approval agencies according to ISO IEC 17025 USA FCC UL A2LA Germany TUV Rheinland Japan VCCI Norway NEMKO Canada INDUSTRY CANADA CSA R O C CNLA BSMI DGT Netherlands Telefication Singapore PSB GOST ASIA MOU Russia CERTIS MOU Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site www adt com tw index 5 phtml If you have any comments please feel free to contact us at the following Linko EMC RF Lab Hsin Chu EMC RF Lab Tel 886 2 26052180 Tel 886 3 5935343 Fax 886 2 26052943 Fax 886 3 5935342 Hwa Ya EMC RF Safety Telecom Lab Linko RF Lab Tel 886 3 3183232 Tel 886 3 3270910 Fax 886 3 3185050 Fax 886 3 3270892 Web Site www adt com tw The address and road map of all our labs can be found in our web site also Report No RM941208L 11 32 Report Format Version 2 0 5
21. t 1 second d The ESD generator was held perpendicularly to the surface to which the discharge was applied and the return cable was at least 0 2 meters from the EUT e Contact discharges were applied to the non insulating coating with the pointed tip of the generator penetrating the coating and contacting the conducting substrate f Air discharges were applied with the round discharge tip of the discharge electrode approaching the EUT as fast as possible without causing mechanical damage to touch the EUT After each discharge the ESD generator was removed from the EUT and re triggered for a new single discharge The test was repeated until all discharges were complete g Atleast ten single discharges in the most sensitive polarity were applied to the Horizontal Coupling Plane at points on each side of the EUT The ESD generator was positioned vertically at a distance of 0 1 meters from the EUT with the discharge electrode touching the HCP h Atleast ten single discharges in the most sensitive polarity were applied to the center of one vertical edge of the Vertical Coupling Plane in sufficiently different positions that the four faces of the EUT were completely illuminated The VCP dimensions 0 5m x 0 5m was placed vertically to and 0 1 meters from the EUT 5 4 4 DEVIATION FROM TEST STANDARD No deviation Report No RM941208L 11 18 Report Format Version 2 0 5 ADT CORP 5 4 5 TEST SETUP w fr Vert
22. the operator c Shall operate as intended after recovering Shall be no degradation of performance see note 2 NOTE 1 Degradation of performance during the test is understood as a degradation to a level not below a minimum performance level specified by the manufacturer for the use of the apparatus as intended In some cases the specified minimum performance level may be replaced by a permissible degradation of performance If the minimum performance level or the permissible performance degradation is not specified by the manufacturer then either of these may be derived from the product description and documentation including leaflets and advertising and what the user may reasonably expect from the apparatus if used as intended No degradation of performance after the test is understood as no degradation below a minimum performance level specified by the manufacturer for the use of the apparatus as intended In some cases the specified minimum performance level may be replaced by a permissible degradation of performance After the test no change of actual operating data or user retrievable data is allowed If the minimum performance level or the permissible performance degradation is not specified by the manufacturer then either of these may be derived from the product description and documentation including leaflets and advertising and what the user may reasonably expect form the apparatus if used as intended 5 3 EUT OPERATING CONDIT
Download Pdf Manuals
Related Search